Guest

CiscoWorks Wireless LAN Solution Engine (WLSE)

Supported Devices Table for the CiscoWorks WLSE and WLSE Express, 2.12

Hierarchical Navigation

Downloads

 Feedback

Table Of Contents

Supported Devices Table for the CiscoWorks Wireless LAN Solution Engine 2.12

Network Management—Supported Access Points and Bridges

Radio Management—Supported Access Points, Radios, and WLSM Blades

Radio Management—Supported Client Adaptor Cards

Radio Management—Supported Directional Antennas

Supported Switches

Supported Routers

Supported Access Servers


Supported Devices Table for the CiscoWorks Wireless LAN Solution Engine 2.12

Revised: 2/21/2006

The following sections show the Cisco devices supported when the CiscoWorks Wireless LAN Solution Engine 2.12 was released:

•Network Management—Supported Access Points and Bridges

•Radio Management—Supported Access Points, Radios, and WLSM Blades

•Radio Management—Supported Client Adaptor Cards

•Radio Management—Supported Directional Antennas

•Supported Switches

•Supported Routers

•Supported Access Servers

To see a list of supported firmware versions, select Administration > System > Firmware Supported Versions.

To see a list of devices discovered by the Wireless LAN Solution Engine, select Devices  > Discover > Managed Devices.

Network Management—Supported Access Points and Bridges

The following devices support basic network management features:

Table 1 Supported Access Points and Bridges 

Series
SysObjectID
Supported Firmware Versions
Discovery, Inventory, Faults, Reporting
Configuration
Firmware

Cisco Aironet 350 series access points1

1.3.6.1.4.1.9.1.552

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA

Cisco Aironet 1100 series access points**

1.3.6.1.4.1.9.1.507

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco 1130 series access points

1.3.6.1.4.1.9.1.618

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1210 and 1230 series access points **

1.3.6.1.4.1.9.1.525

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1240 series access points

1.3.6.1.4.1.9.1.685.

12.3(7)JA*

12.3(7)JA*

12.3(7)JA*

Cisco Aironet 1310 Wireless Bridges

1.3.6.1.4.1.9.1.565

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1310 Wireless Bridges (Repeater/Non-root wireless-clients)

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1310 Wireless Bridges (non-root)

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1310 Workgroup Bridge

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1410 Wireless Bridges

1.3.6.1.4.1.9.1.533

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

* Indicates support for incremental versions. Maintenance releases such as JA1, JA2, etc. are always supported.

** 802.11g radios for Series 1100 and 1200 access points are supported only with 12.2(15)JA or later.

1 Cannot be used as a WDS.


Radio Management—Supported Access Points, Radios, and WLSM Blades

The following devices support basic network management, advanced radio management, and intrusion detection features:

Table 2 Radio Management Supported Access Points and Radios 

Feature
Supported AP Models
Supported Radios
Minimum IOS Version Required

Ad-Hoc Network Detection
AP Radio Scan
Assisted Configuration
Auto Re-Site Survey
Client Walkabout
Interference Detection
Location Manager Radio Monitoring
Rogue AP Detection UnregisteredClient Detection1

Cisco Aironet 1100 series access points

.11b, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco 1130 (Cisco IOS) series access points

.11a, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1210 and 1230 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1240 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(7)JA*

Cisco Aironet 350 IOS series access points2

.11b

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

BR1310 (AP-only mode)

.11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

APs registered to a WLSM-WDS:

•Supported on Cisco Catalyst 6500* series switches (see Supported Switches).

•WLSM software release 1.2(*), 1.3(*), and 1.4(*) **

Authentication/Protection Attack Detection

EMF Transmission Detection
Frame Monitoring 3 4
Switchport Tracing/Suppression

IDS XML APIs used by integrators and third party software5

Cisco Aironet 1100 series access points

.11b, .11g

12.3(4)JA*, 12.3(7)JA

Cisco 1130 (Cisco IOS) series access points

.11a, .11g

12.3(4)JA*, 12.3(7)JA

Cisco Aironet 1210 and 1230 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(4)JA*, 12.3(7)JA

Cisco Aironet 1240 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(7)JA*

BR1310 (AP-only mode)

.11g

12.3(4)JA*, 12.3(7)JA

APs registered to a WLSM-WDS:

•Supported on Cisco Catalyst 6500* series switches (see Supported Switches).

•WLSM software release 1.3(*) and 1.4(*) **

Scanning-Only APs

Cisco Aironet 1100 series access points

.11b, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco 1130 (Cisco IOS) series access points

.11a, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1210 and 1230 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(2)JA*, 12.3(4)JA*, 12.3(7)JA*

Cisco Aironet 1240 series (Cisco IOS) access points

.11a, .11b, .11g

12.3(7)JA*

* Indicates support for incremental versions.

** For more information about WLSM Cat6K module software releases, see http://www.cisco.com/cgi-bin/tablebuild.pl/cat6000-modulesw-wlsm.

1 Unregistered Client Detection is supported only on APs configured in scanning-only mode.

2 A Cisco Aironet 350 IOS series access point cannot be used as a WDS or Scanning-Only AP.

3 Frame Monitoring is supported only on APs configured in scanning-only mode

4 Clients do not participate in Frame Monitoring

5 IDS APIs: WLAN Monitor, Active Termination, and Station Alert. WLAN Monitor and Active Termination are supported only on APs configured in scanning-only mode.


Radio Management—Supported Client Adaptor Cards

Table 3 Radio Management Supported Client Adaptor Cards 

Radio Management Feature
Supported Client Adaptors

All Radio Manager, Sites, and IDS features1

AIR-PCI351x (Air350 based client card, B-radio)2

AIR-CB20A3 , AIR-CB21AG4 5

1 Require CCX-V2 or later compliant clients. To check the status of partner client cards, see the CCX partner website at cetifid.http://www.cisco.com/en/US/partners/pr46/pr147/partners_pgm_concept_home.html

2 To allow the client adaptor to participate in the Radio Management feature, the Enable Radio Management Support parameter must be checked. This parameter, which is accessible from the Advanced (Infrastructure) Parameters screen in ACU, is available in:

2 - Windows ACU version 6.2 or later for 350 series client adapters using firmware version 5.30.17 or later

2 - Windows ACU version 6.3 or later for CB20A client adapters using firmware version 5.40.10 or later

3 See Footnote 2.

4 Requires ADU software version 1.1 or later.

5 Includes both 802.11a and 802.11g radios. The 802.11g radio can act like a 802.11b radio (g is a supersede of b), so effectively the AG client can operate in A, B, and G modes.


Radio Management—Supported Directional Antennas

The following directional antennas are supported:

•AIR-ANT1729 2.4 GHz, 6 dBi Patch Ant w/RP-TNC Connector

•AIR-ANT2410 2.4 GHz, 10dBi Yagi Mast Mount Ant. with RP-TNC Connector

•AIR-ANT2012 2.4 GHz, 6.5 dBi Diversity Patch Ant with RP-TNC Connector

•AIR-ANT3549 2.4 GHz, 9 dBi Patch Antenna with RP-TNC Connector

Supported Switches

The WLSE monitors basic MIB-II attributes that are available on all switches. In general, different software versions of these devices will be supported because those attributes are not expected to change.

Note Catalyst Operating System (CatOS) software is not supported for switch port tracing.

Note Switches configured in a clustered setup are not supported.

Table 4 Supported Switches  

Series
Devices Supported
SysObjectID

Cisco Catalyst 1200

1200

1.3.6.1.4.1.9.5.5

Cisco Catalyst 1900

1924

1.3.6.1.4.1.9.5.18

1.3.6.1.4.1.9.5.28

1912

1.3.6.1.4.1.9.5.175

1.3.6.1.4.1.9.5.31

Cisco PGW 2200 Softswitch

2200

1.3.6.1.4.1.9.5.13

Cisco Catalyst 2820

2820

1.3.6.1.4.1.9.5.20

Cisco Catalyst 29001

2980G-A

1.3.6.1.4.1.9.5.51

2980G

1.3.6.1.4.1.9.5.49

2948GL3Dc

1.3.6.1.4.1.9.1.386

2948G

1.3.6.1.4.1.9.5.42

2926

1.3.6.1.4.1.9.5.35

2900

1.3.6.1.4.1.9.5.12

Cisco Catalyst 2900XL2

2908XL

1.3.6.1.4.1.9.1.170

2912XL

1.3.6.1.4.1.9.1.219

2912MFXL

1.3.6.1.4.1.9.1.221

2916MXL

1.3.6.1.4.1.9.1.171

2924XL

1.3.6.1.4.1.9.1.183

2924CXL

1.3.6.1.4.1.9.1.184

2924XLV

1.3.6.1.4.1.9.1.217

2924CXLV

1.3.6.1.4.1.9.1.218

2924MXL

1.3.6.1.4.1.9.1.220

Cisco Catalyst 29503

2950-12

1.3.6.1.4.1.9.1.323

2950-24

1.3.6.1.4.1.9.1.324

2950-24C

1.3.6.1.4.1.9.1.325

2950T

1.3.6.1.4.1.9.1.359

2950-12G

1.3.6.1.4.1.9.1.427

2950-24G

1.3.6.1.4.1.9.1.428

2950-48G

1.3.6.1.4.1.9.1.429

2950-24S

1.3.6.1.4.1.9.1.430

2950-24GDC

1.3.6.1.4.1.9.1.472

Cisco Catalyst 2970

C2970G-24T

1.3.6.1.4.1.9.1.527

C2970G-24TS

1.3.6.1.4.1.9.1.561

Cisco Catalyst 3000 series switches

C3000

1.3.6.1.4.1.9.5.10

1.3.6.1.4.1.9.5.26

C3100

1.3.6.1.4.1.9.5.23

C3200

1.3.6.1.4.1.9.5.15

CPW16

1.3.6.1.4.1.9.5.9

1.3.6.1.4.1.9.5.25

Cisco Catalyst 3500 XL series switches4

3508GXL

1.3.6.1.4.1.9.1.246

3512XL

1.3.6.1.4.1.9.1.247

3524XL,

1.3.6.1.4.1.9.1.248

3548XL

1.3.6.1.4.1.9.1.278

3524PWRXL,

1.3.6.1.4.1.9.1.287

3524PWRXLEn

1.3.6.1.4.1.9.1.515

Cisco Catalyst 3550 series switches5

3550-24

1.3.6.1.4.1.9.1.366

3550-48

1.3.6.1.4.1.9.1.367

3550-12T

1.3.6.1.4.1.9.1.368

3550-12G

1.3.6.1.4.1.9.1.431

3550-24DC

1.3.6.1.4.1.9.1.452

3550-24-MMF

1.3.6.1.4.1.9.1.453

3550-24PWR

1.3.6.1.4.1.9.1.485

3550-24-PWR

1.3.6.1.4.1.9.1.485

Cisco Catalyst 3560 series switches

3560-24PS

1.3.6.1.4.1.9.1.563

356048PS

1.3.6.1.4.1.9.1.564

Cisco Catalyst 3750 series switches

3750

1.3.6.1.4.1.9.1.516

3750-24TS

1.3.6.1.4.1.9.1.511

3750-248TS

1.3.6.1.4.1.9.1.512

3750G-24S

1.3.6.1.4.1.9.1.513

3750G-24T

1.3.6.1.4.1.9.1.514

Cisco Catalyst 3900 series switches

3900

1.3.6.1.4.1.9.5.33

3920

1.3.6.1.4.1.9.5.37

Cisco Catalyst 4000 series switches6

4003

1.3.6.1.4.1.9.5.40

4912G,

1.3.6.1.4.1.9.5.41

4006

1.3.6.1.4.1.9.5.46

4006-SW

1.3.6.1.4.1.9.1.448

4908gL3Dc

1.3.6.1.4.1.9.1.387

4503

1.3.6.1.4.1.9.1.501

Cisco Catalyst 4000 IOS series switches7

4006-SW

1.3.6.1.4.1.9.1.448

4503

1.3.6.1.4.1.9.1.501

4503-SUP

1.3.6.1.4.1.9.5.58

4506

1.3.6.1.4.1.9.1.502

4506-SUP

1.3.6.1.4.1.9.5.59

4507R

1.3.6.1.4.1.9.1.503

Cisco Catalyst 5000 series switches8

5000

1.3.6.1.4.1.9.5.7

5002

1.3.6.1.4.1.9.5.29

Cisco Catalyst 5500 series switches9

5500

1.3.6.1.4.1.9.5.17

5505

1.3.6.1.4.1.9.5.34

5509

1.3.6.1.4.1.9.5.36

Cisco Catalyst 6000* series switches10

6006

1.3.6.1.4.1.9.5.38

6009

1.3.6.1.4.1.9.5.39

Cisco Catalyst 6000* IOS series switches

6006

1.3.6.1.4.1.9.1.280

6009

1.3.6.1.4.1.9.1.281

Cisco Catalyst 6500* series switches

6503

1.3.6.1.4.1.9.5.56

6506

1.3.6.1.4.1.9.5.45

6509

1.3.6.1.4.1.9.5.44

6509SP

1.3.6.1.4.1.9.5.47

6513

1.3.6.1.4.1.9.5.50

Cisco Catalyst 6500* IOS series switches

6506

1.3.6.1.4.1.9.1.28

6509

1.3.6.1.4.1.9.1.283

6509SP

1.3.6.1.4.1.9.1.310

6513

1.3.6.1.4.1.9.1.400

* The Wireless LAN Services Module (WLSM) can be implemented in these switches to provide WDS to the wireless network.The Sys Object ID for the WLSM is 1.3.6.1.4.1.9.1.599.

1 Tested with Software Release 12.0(7)WX5(15a)

2 Tested with Software Release 11.2  (8.5)SA6

3 Tested with Software Release 12.0(5.3)WC(1) and 12.1(9)EA1

4 Tested with Software Release 12.0(5.3)WC(1), 12.0(5.2)XU

5 Tested with Software Release 12.1(6)EA1

6 Tested with Software Release 6.3 (3) and 7.2(2)

7 Tested with Software Release 12.1(12c)EW

8 Tested with Software Release 4.5(3)

9 Tested with Software Release 5.4(1)

10 Tested with Software Releases 6.2(2) and 6.3(1)


Supported Routers

Note The WLSE monitors basic MIB-II attributes that are available on all switches. In general, different software versions of these devices will be supported because those attributes are not expected to change.

Table 5 Supported Routers

Series
Devices Supported
SysObjectID

Cisco 800 series routers

801

1.3.6.1.4.1.9.1.212

802

1.3.6.1.4.1.9.1.213

803

1.3.6.1.4.1.9.1.214

804

1.3.6.1.4.1.9.1.215

804J

1.3.6.1.4.1.9.1.296

805

1.3.6.1.4.1.9.1.245

806

1.3.6.1.4.1.9.1.384

811

1.3.6.1.4.1.9.1.295

813

1.3.6.1.4.1.9.1.396

826

1.3.6.1.4.1.9.1.322

826 QuadV

1.3.6.1.4.1.9.1.321

827

1.3.6.1.4.1.9.1.284

827-H

1.3.6.1.4.1.9.1.446

827 QuadV

1.3.6.1.4.1.9.1.270

828

1.3.6.1.4.1.9.1.382

831

1.3.6.1.4.1.9.1.497

837

1.3.6.1.4.1.9.1.495

Cisco 1700 series routers

1710

1.3.6.1.4.1.9.1.200

1721

1.3.6.1.4.1.9.1.444

1760

1.3.6.1.4.1.9.1.416

Cisco 2600 series routers1

2610

1.3.6.1.4.1.9.1.185

2611

1.3.6.1.4.1.9.1.186

2612

1.3.6.1.4.1.9.1.187

2613

1.3.6.1.4.1.9.1.195

2620

1.3.6.1.4.1.9.1.208

2621

1.3.6.1.4.1.9.1.209

2650

1.3.6.1.4.1.9.1.319

2651

1.3.6.1.4.1.9.1.320

2691

1.3.6.1.4.1.9.1.413

2610XM

1.3.6.1.4.1.9.1.466

2611XM

1.3.6.1.4.1.9.1.467

2620XM

1.3.6.1.4.1.9.1.468

2621XM

1.3.6.1.4.1.9.1.469

2650XM

1.3.6.1.4.1.9.1.470

2651XM

1.3.6.1.4.1.9.1.471

Cisco 3600 series routers2

3620

1.3.6.1.4.1.9.1.122

3640

1.3.6.1.4.1.9.1.110

3660

1.3.6.1.4.1.9.1.205

3661-AC

1.3.6.1.4.1.9.1.338

3661-DC

1.3.6.1.4.1.9.1.339

3662-AC

1.3.6.1.4.1.9.1.340

3662-AC-CO

1.3.6.1.4.1.9.1.342

3662-DC

1.3.6.1.4.1.9.1.341

3662-DC-CO

1.3.6.1.4.1.9.1.343

Cisco 7600 Series. routers

7603

1.3.6.1.4.1.9.1.401

7606

1.3.6.1.4.1.9.1.402

1 Tested with Cisco IOS Software Release 12.2(1)

2 Tested with Cisco IOS Software Release 12.0(5)XK


Supported Access Servers

Table 6 Supported Access Servers

AAA Servers
Version
Supported Protocols for Fault Monitoring

Cisco Secure Access Control Server (ACS)

3.31

LEAP, PEAP, RADIUS, EAP-FAST, and EAP-MD5 servers.

Cisco Access Registrar (CAR)

4.0

RADIUS, LEAP, and EAP-MD5 servers.

1030 WLSE Express Embedded AAA Server

N/A

LEAP, PEAP, or RADIUS servers.

1 The WLSE does not support monitoring of Microsoft PEAP (EAP-MSCHAPv2) protocol setup on any AAA server.