Cisco Service and Application Module for IP User Guide

SAMI LCP Commands

The following commands, listed in alphabetical order, are introduced or modified for the Cisco SAMI, and are supported at a SAMI LCP console:

•boot eobc: (LCP ROM monitor command)

•clear cde

•clear cores

•clear daughtercard fpga statistics

•confreg (LCP ROM monitor)

•console-select

•debug sami bouncer_svc

•debug sami dc_health

•debug sami ppc_download

•debug sami session_agent

•delete

•dir

•erase ppc-flash

•exception ixp

•hostname

•interface

•ip route

•processor config-register (LCP ROM monitor command)

•processor config-register

•reload

•reload sami processor

•reprogram bootflash

•set cde destindex

•set cde vlan

•show cde

•show cde destindex

•show cde vlan

•show daughtercard fpga statistics

•show daughtercard registers

•show login timeout

•show running-config

•show startup-config

•show tech-support

•show version

•upgrade-rommon

•write

boot eobc:

To boot the SAMI from the image on the supervisor engine, use the boot eobc: ROM-monitor command.

boot eobc:

Syntax Description

This command has no keywords or arguments.

Defaults

No default behavior or values exist.

Command Modes

ROM monitor

Command History

Usage Guidelines

Use the boot eobc: command to boot the SAMI using the image on the supervisor engine.

Examples

The following example shows how to boot the SAMI from the image on the supervisor engine:

rommon 1> boot eobc:

Related Commands

clear cde

To clear the classification and distribution engine (CDE) statistics and interrupt counts, use the clear cde command.

clear cde {interrupt | stats}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

This command clears the statistics and counts that display using the show cde command.

Note This command is for use by trained personnel for troubleshooting purposes only.

Examples

To clear the CDE interrupt counts, enter:

switch# clear cde interrupt

Related Commands

clear cores

To clear all of the core dumps stored in the core file system, use the clear cores command.

clear cores

Syntax Description

This command has no keywords or arguments.

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

To view the list of core files in the core file system, use the dir core command.

To save a copy of a core dump to a remote server before clearing it, use the copy capture command.

To delete a specific core dump file from the core file system, use the delete core command.

Note The SAMI creates a core dump when it experiences a fatal error. Core dump information is for Cisco Technical Assistance Center (TAC) use only. We recommend that you contact TAC for assistance in interpreting information in a core dump.

Examples

To clear all core dumps, enter:

switch# clear cores

Related Commands

clear daughtercard fpga statistics

To clear all field programmable gate array (FPGA) statistics for a SAMI daughter card, use the clear daughtercard fpga statistics command.

clear daughtercard card_number fpga statistics

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

This command clears the statistics displayed by the show daughtercard fpga statistics command.

Examples

To clear all FPGA statistics on SAMI daughter card 1, enter:

switch# clear daughtercard 1 fpga statistics

Related Commands

config-register

To change the configuration register settings of the SAMI LCP, use the config-register command.

config-register value

Syntax Description

Defaults

This command has no default.

Command Modes

Configuration

Command History

Usage Guidelines

The config-register command affects only the configuration register bits that control the boot field and

leaves the remaining bits unaltered.

To configure the SAMI LCP to autoboot the system image identified in the boot environment variable, use the config-register command and set the configuration register to 1.

Examples

The following example sets the boot field in the configuration register to boot the system image identified in the Boot environment variable upon reboot:

switch(config)# config-register 1

Command History

confreg (LCP ROM monitor)

To change the configuration register settings while in ROM monitor mode, use the confreg command in ROM monitor mode.

confreg value

Syntax Description

Defaults

This command has no default.

Command Modes

ROM monitor

Command History

Usage Guidelines

The config-register command affects only the configuration register bits that control the boot field and

leaves the remaining bits unaltered.

Examples

The following example sets the boot field in the configuration register to boot the system image identified in the Boot environment variable upon reboot:

rommon 1># confreg 1

Related Commands

console-select

To configure a SAMI powerPC (PPC) on daughter card 1 to be accessible from the console port on the SAMI front panel, use the console-select db1 command.

console-select {db1 processor_number | db2 processor_number}

Syntax Description

Defaults

Daughter card 1—Console 3 is connected to the daughter card 1 console port on the SAMI front panel.

Daughter card 2—Console 6 is connected to the daughter card 2 console port on the SAMI front panel.

Command Modes

Configuration

Command History

Usage Guidelines

Use this command to configure one of the three PPCs on daughter card 1 of a SAMI to be accessible externally using the daughter card console port on the SAMI front panel.

By default, PPC 3 can be accessed by console port for db1 and PPC 6 can be accessed by console port of db2. After a different PPC is configured to be accessible from the console port on the SAMI front panel using the console-select commands, the newly configured PPC will continue to be accessible across router reloads.

Examples

To configure the PPC4 on daughter card 1 to be accessible from the daughter 1 console port on the SAMI front panel, enter:

switch(config)# console-select db1 4

debug sami bouncer_svc

To display information on bouncer svc daemon processing, use the debug sami bouncer_svc command in privileged EXEC mode. To disable debugging output, use the no form of this command.

debug sami bouncer {errors | events | packets}

no debug sami bouncer {errors | events | packets}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the debug sami bouncer_svc command to view bouncer svc daemon debugging information.

Examples

The following example shows events that occur during bouncer svc daemon processing.

switch# debug sami bouncer_svc events

debug sami dc_health

To display information on sami cd health daemon processing, use the debug sami dc_health command in privileged EXEC mode. To disable debugging output, use the no form of this command.

debug sami dc_health {errors | events}

no debug sami dc_health {errors | events}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the debug sami dc_health command to view sami cd health daemon debugging information.

Examples

The following example shows events that occur during sami cd health processing.

switch# debug sami dc_health events

debug sami ppc_download

To display information on ppc download daemon processing, use the debug sami ppc_download command in privileged EXEC mode. To disable debugging output, use the no form of this command.

debug sami ppc_download {errors | events}

no debug sami ppc_download {errors | events}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the debug sami ppc_download command to view ppc download daemon debugging information.

Examples

The following example shows errors that occur during ppc download daemon processing.

switch# debug sami ppc_download errors

debug sami session_agent

To display information on session agent daemon processing, use the debug sami session_agent command in privileged EXEC mode. To disable debugging output, use the no form of this command.

debug sami session-agent {errors | events | packets}

no debug sami session-agent {errors | events | packets}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the debug sami session-agent command to view session agent daemon debugging information.

Examples

The following example shows errors that occur during session agent processing.

switch# debug sami session_agent errors

delete

To delete a specific file in the LCP file system, use the delete command.

delete {core:filename | disk0:[path/]filename | image:filename | volatile:filename}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

To delete a specific file from the LCP file system, use the delete command.

If you do not specify a filename with the file system keyword, the SAMI LCP prompts you for a filename.

To display the list of files that reside in a file system, use the dir sami# command.

Examples

The following example shows how to delete a file named "0x401_VSH_LOG.25256.TAR.GZ" from the core file system:

switch# delete core:0x401_VSH_LOG.25256.TAR.GZ

Related Commands

dir

To list files in the various file systems on the LCP, use the dir command.

dir {core: | disk0: | image: | volatile}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the dir command to list the files in the various file systems on the SAMI LCP.

To delete a file from a file system, use the delete command. To delete all core dumps, use the clear cores command.

Examples

The following example shows how to display the contents of the disk0 file system:

switch# dir disk0:

Related Commands

erase ppc-flash

To erase the ROM monitor area of a SAMI powerPC (PPC) boot flash and program ROM monitor using the default image in the SAMI software bundle, use the erase ppc-flash command.

erase ppc-flash [image_name:] {ppc_number | all-ppc}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use the erase ppc-flash command to erase the ROM monitor area of the PPC boot flash and program ROM monitor using the default image in the SAMI software bundle.

Examples

To erase the ROM monitor area of the boot flash on PCC 6 and program ROM monitor using the image in the SAMI software bundle, enter:

switch# erase ppc-flash image_name 6

Related Commands

This command has no related commands.

exception ixp

To enable a coredump to be collected from IXP, use the exception ixp command in configuration mode. Use the no form of the command to disable collecting coredump information.

exception ixp IXP-Proc

no exception ixp

Syntax Description

Defaults

none

Command Modes

Configuration

Command History

Usage Guidelines

The coredump gets stored under "crashinfo_collection-XXXXX-YYYY.tar", which resides on LCP "dir:core". The naming convention for the coredump file is as below :-

coredump_proc<Num>- XXXXX-YYYY.gz

where

Num -- Represents either 1 or 2 depending on IXP1 or IXP2 respectively

XXXXX-YYYY-- Represents the timestamp

Caution Collecting IXP coredump will increase reboot time by an average of 4 to 5 minutes.

Examples

To change the hostname of the SAMI LCP from host1 to SAMI1-LCP, enter:

switch(config)# hostname SAMI1-LCP

SAMI_LCP(config)# exception ixp 1

				  exception ixp 2

hostname

To change the hostname of the SAMI LCP, use the hostname command. Use the no form of this command to reset the hostname to the default of switch.

hostname name

no hostname name

Syntax Description

Defaults

The hostname is host1.

Command Modes

Configuration

Command History

Usage Guidelines

By default, the hostname for the SAMI LCP is host1.

The hostname is used for the command line prompts and default configuration filenames. If you establish sessions to multiple devices, the hostname helps you track where you enter commands.

Examples

To change the hostname of the SAMI LCP from host1 to SAMI1-LCP, enter:

switch(config)# hostname SAMI1-LCP

SAMI_LCP(config)# 

Related Commands

This command has no related commands.

interface

To create a bridge-group virtual interface (BVI) or VLAN interface, use the interface command. To remove the interface, use the no form of this command.

interface {bvi group_number | vlan number}

no interface {bvi group_number | vlan number}

Note If a VLAN interface is configured on the LCP, then a sub-interface for the same VLAN should not be configured on the PPCs.

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

Configuration

Command History

Usage Guidelines

Use the interface command to create a BVI or VLAN interface.

When entered, the command prompt changes to (config-if).

Examples

To assign VLAN interface 100 to the Admin context and access interface configuration mode, enter:

switch(config)# interface vlan 100

switch(config-if)#

Related Commands

ip route

To configure a default or static IP route, use the ip route command. Use the no form of this command to remove a default or static IP route from the configuration.

ip route dest_ip_prefix netmask gateway_ip_address

no ip route dest_ip_prefix netmask gateway_ip_address

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

Configuration

Command History

Usage Guidelines

The default route identifies the router IP address to which the SAMI LCP sends all IP packets for which it does not have a route.

Dynamic routing is not supported. You must use static routes for any networks to which the SAMI LCP is not directly connected; for example, use a static route when there is a router between a network and the SAMI LCP.

The SAMI LCP supports up to eight equal cost routes on the same interface for load balancing.

Routes that identify a specific destination address take precedence over the default route.

Examples

To configure a default route, set the IP address and the subnet mask for the route to 0.0.0.0. For example, if the SAMI LCP receives traffic that it does not have a route, it sends the traffic out the interface to the router at 192.168.4.8, enter:

switch(config)# ip route 0.0.0.0 255.255.255.0 192.168.4.8

processor config-register

To change the configuration register settings of a SAMI PPC, use the processor config-register configuration command.

processor {proc_number | all-ppc} config-register value

no processor {proc_number | all-ppc} config-register value

Syntax Description

Defaults

0—The front panel connection rather than the on-the-board connection will make the PPCs automatically load the Cisco software application image upon startup.

Command Modes

Configuration

Command History

Usage Guidelines

You can modify the boot method that a SAMI PPC uses at the next startup by setting the boot field in the software configuration register. The configuration register identifies how the PPC should boot and where the system image is stored. You can modify the boot field to force a PPC to boot a particular system image at startup instead of using the default system image.

The processor config-register command affects only the configuration register bits that control the boot field and leaves the remaining bits unaltered.

Examples

The following example sets the boot field in the configuration register to boot the system image identified in the BOOT environment variable upon reboot for PPC 5:

switch(config)# processor 5 config-register 1

Related Commands

reload

To reload the configuration on the SAMI LCP, use the reload command.

reload

Syntax Description

This command has no keywords or arguments.

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The reload command reboots the SAMI LCP and performs a full power cycle of both the hardware and software. The reset process can take several minutes. Any open connections with the SAMI are dropped after you enter the reload command.

Caution Configuration changes that have not been written to flash memory are lost during a reload. Before reloading, enter the copy running-conf startup-config command to save a copy of the running configuration to the startup configuration in flash memory. If you fail to save your running configuration changes, the SAMI LCP reverts to the last saved version of the startup configuration when restarted.

Examples

To execute a soft reboot, enter:

switch# reload

This command will reboot the system

Save configurations for all the contexts. Save? [yes/no]: [yes]

Related Commands

reload sami processor

To reload a specific SAMI powerPC (PPC), use the reload sami processor command.

reload sami processor {ppc_num | all-ppc}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The reload sami processor command reboots a single SAMI PPC. The reload process can take several minutes. Any open connections with the SAMI PPC are dropped after you enter the reload sami processor command.

Caution Configuration changes that have not been written to flash memory are lost during a reload. Therefore, before reloading, enter the copy running-conf startup-config command to save a copy of the running configuration to the startup configuration in flash memory. If you fail to save your running configuration changes, the PPC reverts to the last saved version of their startup configuration when restarted.

Note This command is not available for distributed Cisco software applications such as the Cisco Content Services Gateway - 2nd Generation.

Examples

To reload processor 4 on a SAMI, enter:

switch# reload sami processor 4

Related Commands

reprogram bootflash

To reprogram the Field Upgradable (FUR) partition of the rommon image on the LCP, use the reprogram bootflash command with the fur-image keyword specified.

reprogram bootflash fur-image

Syntax Description

Command Modes

Command History

Usage Guidelines

The reprogram bootflash command is for use by trained Cisco personnel only. Entering this command may cause unexpected results. Do not attempt to use the reprogram bootflash command without guidance from Cisco support personnel.

Examples

To reprogram the rommon image FUR partition on the image: file system, enter:

switch# reprogram bootflash fur-image

Related Commands

This command has no related commands.

set cde destindex

To set the destination index table from index x to y to one of several options, use the set cde destindex command in EXEC configuration mode. Use the no form of the command to disable this feature.

set cde destindex x [to y] [cp | ixp0 | ixp1 | nitrox | dc1 | dc2 | invalid]

no set cde destindex

Syntax Description

Command Default

The default value is invalid..

Command Modes

Command History

Usage Guidelines

This command is only available with the debug plugin for the LCP.

Examples

Here is an example of the set cde destindex command:

SAMI-slot8# set cde destindex 0 to 4 dc2

dest index 3 lsb 0 - 4 dest dc2

set cde vlan

To configure vlan destinations for packets in a VLAN(s) to one of several options, use the set cde vlan command in privileged EXEC mode.

set cde vlan x [cp | ixp0 | ixp1 | nitrox | dc1 | dc2 | invalid | gtpipdesthash | ipsrchash ]

Syntax Description

Command Default

By default, CDE destinations in enhanced CDE (version 406 onwards) is set to gtpipdesthash. For previous versions of CDE, the CDE destination is set to ixp0 by default.

Command Modes

Command History

Usage Guidelines

Caution This command has a direct impact on the packet processing in SAMI PPC and IXP processors. You should only use this command when directed by Cisco Technical Assistance Center (TAC) engineers.

---

Examples

Here is an example of the set cde vlan command:

SAMI-LCP# set cde vlan 100 ixp1

This can drastically affect the way system behaves.Are you sure? [yes/no] [no] yes

vlan 100 dest ixp1 

SAMI-LCP# set cde vlan 101 gtpipdesthash

This can drastically affect the way system behaves.Are you sure? [yes/no] [no] yes

vlan 101 dest gtpipdesthash 

SAMI-LCP#set cde vlan 102 to 105 ipsrchash

This can drastically affect the way system behaves.Are you sure? [yes/no] [no] yes

vlan 102 - 105 dest ipsrchash

If a vlan in the range is being used by the LCP (proc 0), a warning is issued that the particular vlan is being used by the LCP and that VLAN is dropped from the configuration. The sample output of the command is as follows:

	SAMI-LCP# set cde vlan 7 to 12 ixp1

vlan 7 - 12 dest ixp1 

Warning: vlan 10 is being used by proc 0 and this CLI will not update it.

Please use 'set cde vlan 10' to override.

SAMI-LCP# set cde vlan 10 ixp1

show cde

To display the classification and distribution engine (CDE) register values, use the show cde command.

show cde {all | count | dist | hash index_number | health | interrupts | reg cde_number register | stats {cumulative | stats} | vlan vlan_number} [|] [>]

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

This command is for use by trained Cisco personnel for troubleshooting purposes only. You can also use the show cde vlan command to verify if the CDE is programmed correctly for the subscriber VLAN.

Examples

To display all of the CDE register values, enter:

switch# show cde all

Related Commands

show cde destindex

To display the destination index table for all indices x to y, use the show cde destindex command in EXEC mode.

show cde vlan x [to y]

Syntax Description

There are no arguments or keywords.

Defaults

0 <= x <= y <= 7

Command Modes

EXEC

Command History

Usage Guidelines

Examples

To display destinations for all vlans from x to y enter:

slot8# show cde destindex 0 to 7

Destination index & 0x7 == 0 --> daughter card 2

Destination index & 0x7 == 1 --> daughter card 2

Destination index & 0x7 == 2 --> daughter card 2

Destination index & 0x7 == 3 --> daughter card 2

Destination index & 0x7 == 4 --> daughter card 2

Destination index & 0x7 == 5 --> ixp1

Destination index & 0x7 == 6 --> ixp0

Destination index & 0x7 == 7 --> ixp1

show cde vlan

To display destinations for the specified VLANs, use the show cde vlan command in EXEC mode.

show cde vlan vlan_id [ to vlan_id ]

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Examples

To display destinations for all vlans from x to y enter:

SAMI-LCP# show cde vlan 7 to 12

Vlan 7 --> ixp1 

Vlan 8 --> ixp0 

Vlan 9 --> gtpipdesthash 

Vlan 10 --> ipsrchash

Vlan 11 --> cp

Vlan 12 --> ixp1 

show daughtercard fpga statistics

To display the field programmable gate array (FPGA) statistics for a daughter card on the SAMI, use the show daughtercard fpga statistics command.

show daughtercard card_number fpga statistics

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

If a daughter card number is not specified, the FPGA statistics for both daughter cards will display.

Examples

To display the FPGA statistics for daughter card 2, enter:

switch# show daughtercard 2 fpga statistics

Related Commands

show daughtercard registers

To display the field programmable gate array (FPGA) or complex programmable logic device (CPLD) registers for a daughter card on the SAMI, use the show daughtercard registers command.

show daughtercard card_number [fpga | cpld] registers

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

If a daughter card number is not specified, the FPGA and/or CPLD registers for both daughter cards will display.

Examples

To display the FPGA counters for daughter card 2, enter:

switch# show daughtercard 2 fpga registers

Related Commands

show login timeout

To display the amount of time, a session can remain inactive before it is ended (the login session idle timeout value), use the show login timeout command.

show login timeout

Syntax Description

This command has no keywords or arguments.

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

To configure the login timeout value, use the login timeout command in configuration mode.

Examples

To display the login timeout value, enter:

switch# show login timeout

Related Commands

show running-config

To display the running configuration information on the SAMI LCP, use the show running-config command.

show running-config [aaa | access-list | action-list | class-map | context | dhcp | domain | ft | interface | object-group | parameter-map | policy-map | probe | resource-class | role | rserver | serverfarm | sticky] [|] [>]

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The show running-config command is a context-sensitive command.

Use the copy capture command to do the following:

•Save a copy of the running configuration to a file on one or more destination locations.

•Save the running configuration as the startup configuration.

•Save the startup configuration as the running configuration.

Examples

To display the entire running configuration, enter:

switch# show running-config

Related Commands

show startup-config

To display information about the startup configuration on the SAMI LCP, use the show startup-config command.

show startup-config [|] [>]

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

To clear the startup configuration, use the clear startup-config command. To copy the running configuration to the startup configuration, or copy the startup configuration to the running configuration, use the copy running-config command.

Examples

To display information about the startup configuration, enter:

switch# show start-config

Related Commands

show tech-support

To display information that is useful to technical support when reporting a problem with your SAMI LCP, use the show tech-support command.

show tech-support [details] [|] [>]

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The show tech-support command is useful when collecting a large amount of information about your SAMI LCP for troubleshooting purposes with Cisco technical support. The output of this command can be provided to technical support representatives when reporting a problem.

The show tech-support command displays the output of several show commands at once. The output from this command varies depending on your configuration. The default output of the show tech-support command includes the output of the following commands:

•show environment—See the show environment command.

•show hardware—See the show hardware command.

•show interface—See the show interface command.

•show process—See the show processes command.

•show running-config—See the show running-config command.

•show version—See the show version command.

Explicitly set the terminal length command to 0 (zero) to disable autoscrolling and enable manual scrolling. Use the show terminal command to view the configured terminal size. After obtaining the output of this command, reset your terminal length as required.

You can save the output of this command to a file by appending > filename to the show tech-support command. If you save this file, verify that you have sufficient space to do so as each of these files may take about 1.8 MB.

Examples

To display the summary version of the technical support report, enter:

switch# show tech-support

Related Commands

show version

To display the version information of system software that is loaded in flash memory and currently running on the SAMI LCP, use the show version command.

show version| >

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The show version command also displays information related to the following SAMI hardware components:

•Slot number—Slot number that the SAMI LCP occupies on the Cisco 7600 series chassis.

•CPU—Number of CPUs and type and model

•Memory—Total and shared volatile memory

•Flash memory—Total and used flash memory

Use the show version command to verify the software version on the SAMI LCP before and after an upgrade.

Examples

To display the software version information, enter:

switch# show version

upgrade-rommon

To upgrade the ROM monitor of one or more of the SAMI PPCs with a specific ROM monitor image, use the upgrade-rommon command.

upgrade-rommon rommon_image {ppc_num | all-ppc}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

Use this command to upgrade the ROM monitor of one or more of the SAMI PPCs with a specific ROM monitor image.

Examples

To upgrade the ROM monitor image on SAMI PPC 3, enter:

switch# upgrade-rommon image_name 3

Related Commands

This command has no related commands.

write

To manage persistent and nonpersistent configuration information, use the write command.

write {erase | memory [all] | terminal}

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

EXEC

Command History

Usage Guidelines

The different versions of this command require the following user role or feature in your user role:

•write erase—Admin user

•write mem—config-copy feature

•write all—Admin user

To write the running configuration to the startup configuration, you can also use the copy running-config startup-config command. To erase the startup configuration, you can also use the clear startup-config command. To display the running configuration, you can also use the show running-config command.

Examples

To write running configuration to the startup configuration, enter:

switch# write memory

Related Commands

Network Processor Console Command

The following command is supported at the IXP console:

•shutdown

shutdown

To shut down the network processor (IXP) on the SAMI, use the shutdown command.

shutdown

Syntax Description

Defaults

No default behavior or values exist.

Command Modes

Command History

Usage Guidelines

Use this command to shutdown the network processor (IXP) on the SAMI.

Examples

The following examples illustrates how to use the shutdown command.

shutdown