A workgroup bridge (WGB) is a mode that can be configured on an autonomous IOS access point to provide wireless connectivity to a lightweight access point on behalf of clients that are connected by Ethernet to the WGB access point. A WGB connects a wired network over a single wireless segment by learning the MAC addresses of its wired clients on the Ethernet interface and reporting them to the lightweight access point using Internet Access Point Protocol (IAPP) messaging. The WGB provides wireless access connectivity to wired clients by establishing a single wireless connection to the lightweight access point. The lightweight access point treats the WGB as a wireless client.
A Cisco IOS AP as a WGB using the Cisco IOS 15.2 or later releases support Protected Extensible Authentication Protocol (PEAP) with the controller.
Figure 1. WGB Example
If the lightweight access point fails, the WGB attempts to associate to another access point.
Guidelines and Limitations
The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.
If your access point has two radios, you can configure only one for workgroup bridge mode. This radio is used to connect to the lightweight access point. We recommend that you disable the second radio.
Enable the workgroup bridge mode on the WGB as follows:
On the WGB access point GUI, choose Workgroup Bridge for the role in radio network on the Settings > Network Interfaces page.
On the WGB access point CLI, enter the station-role workgroup-bridge command.
These features are not supported for use with a WGB:
Cisco Centralized Key Management (CCKM)
If a WGB associates to a web-authentication WLAN, the WGB is added to the exclusion list, and all of the WGB wired clients are deleted.
The WGB supports a maximum of 20 wired clients. If you have more than 20 wired clients, use a bridge or another device.
Wired clients connected to the WGB are not authenticated for security. Instead, the WGB is authenticated against the access point to which it associates. Therefore, we recommend that you physically secure the wired side of the WGB.
The DirectStream feature from the controller does not work for clients behind workgroup bridges and the stream is denied.
With Layer 3 roaming, if you plug a wired client into the WGB network after the WGB has roamed to another controller (for example, to a foreign controller), the wired client’s IP address displays only on the anchor controller, not on the foreign controller.
If a wired client does not send traffic for an extended period of time, the WGB removes the client from its bridge table, even if traffic is continuously being sent to the wired client. As a result, the traffic flow to the wired client fails. To avoid the traffic loss, prevent the wired client from being removed from the bridge table by configuring the aging-out timer on the WGB to a large value using the following Cisco IOS commands on the WGB:
bridge bridge-group-number aging-time seconds
where bridge-group-number is a value between 1 and 255, and seconds is a value between 10 and 1,000,000 seconds. We recommend configuring the seconds parameter to a value greater than the wired client’s idle period.
When you delete a WGB record from the controller, all of the WGB wired clients’ records are also deleted.
Wired clients connected to a WGB inherit the WGB’s QoS and AAA override attributes.
These features are not supported for wired clients connected to a WGB:
To enable the WGB to communicate with the lightweight access point, create a WLAN and make sure that Aironet IE is enabled.
The broadcast forwarding toward wired WGB clients works only on the native VLAN. If additional VLANs are configured, only the native VLAN forwards broadcast traffic.
Wired clients behind a WGB cannot connect to a DMZ/Anchor controller. To enable wired clients behind a WGB to connect to an anchor controller in a DMZ, you must enable VLANs in the WGB using the config wgb vlan enable command.
WGB Configuration Example
The following is an example of the configuration of a WGB access point using static WEP with a 40-bit WEP key:
ap# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
ap(config)# dot11 ssid WGB_with_static_WEP
ap(config-ssid)# authentication open
ap(config)# interface dot11Radio 0
ap(config)# station-role workgroup-bridge
ap(config-if)# encry mode wep 40
ap(config-if)# encry key 1 size 40 0 1234567890
ap(config-if)# ssid WGB_with_static_WEP
Verify that the WGB is associated to an access point by entering this command on the WGB:
show dot11 association
Information similar to the following appears:
ap# show dot11 associations
802.11 Client Stations on Dot11Radio0:
SSID [FCVTESTING] :
MAC Address IP address Device Name Parent State
000b.8581.6aee 10.11.12.1 WGB-client map1 - Assoc
Viewing the Status of Workgroup Bridges (GUI)
Choose Monitor > Clients to open the Clients page.
The WGB text box on the right side of the page indicates whether any of the clients on your network are workgroup bridges.
Click the MAC address of the desired client. The Clients > Detail page appears.
The Client Type text box under Client Properties shows “WGB” if this client is a workgroup bridge, and the Number of Wired Client(s) text box shows the number of wired clients that are connected to this WGB.
See the details of any wired clients that are connected to a particular WGB as follows:
Click Back on the Clients > Detail page to return to the Clients page.
Hover your cursor over the blue drop-down arrow for the desired WGB and choose Show Wired Clients. The WGB Wired Clients page appears.
If you want to disable or remove a particular client, hover your cursor over the blue drop-down arrow for the desired client and choose Remove or Disable, respectively.
Click the MAC address of the desired client to see more details for this particular client. The Clients > Detail page appears. The Client Type text box under Client Properties shows “WGB Client,” and the rest of the text boxes on this page provide additional information for this client.
Viewing the Status of Workgroup Bridges (CLI)
See any WGBs on your network by entering this command:
show wgb summary
See the details of any wired clients that are connected to a particular WGB by entering this command:
show wgb detailwgb_mac_address
Debugging WGB Issues (CLI)
Before You Begin
Enable debugging for IAPP messages, errors, and packets by entering these commands:
debug iapp all enable—Enables debugging for IAPP messages.
debug iapp error enable—Enables debugging for IAPP error events.
debug iapp packet enable—Enables debugging for IAPP packets.
Debug an roaming issue by entering this command:
debug mobility handoff enable
Debug an IP assignment issue when DHCP is used by entering these commands:
debug dhcp message enable
debug dhcp packet enable
Debug an IP assignment issue when static IP is used by entering these commands: