The Radio Resource Management (RRM) software embedded in the controller acts as a built-in RF engineer to consistently provide real-time RF management of your wireless network. RRM enables controllers to continually monitor their associated lightweight access points for traffic load, interference, noise, and coverage.
The table below lists the CLI keyboard shortcuts to help you enter and edit command lines on the controller.
Table 1 CLI Command Keyboard Shortcuts
Action
Description
Keyboard Shortcut
Change
The word at the cursor to lowercase.
Esc I
The word at the cursor to uppercase.
Esc u
Delete
A character to the left of the cursor.
Ctrl-h, Delete, or Backspace
All characters from the cursor to the beginning of the line.
Ctrl-u
All characters from the cursor to the end of the line.
Ctrl-k
All characters from the cursor to the end of the word.
Esc d
The word to the left of the cursor.
Ctrl-w or Esc Backspace
Display MORE output
Exit from MORE output.
q, Q, or Ctrl-C
Next additional screen. The default is one screen. To display more than one screen, enter a number before pressing the Spacebar key.
Spacebar
Next line. The default is one line. To display more than one line, enter the number before pressing the Enter key.
Enter
Enter an Enter or Return key character.
Ctrl-m
Expand the command or abbreviation.
Ctrl-t or Tab
Move the cursor
One character to the left (back).
Ctrl-b or Left Arrow
One character to the right (forward).
Ctrl-f or Right Arrow
One word to the left (back), to the beginning of the current or previous word.
Esc b
One word to the right (forward), to the end of the current or next word.
Esc f
To the beginning of the line.
Ctrl-a
To the end of the line.
Ctrl-e
Redraw the screen at the prompt.
Ctrl-l or Ctrl-r
Return to the EXEC mode from any configuration mode
Ctrl-z
Return to the previous mode or exit from the CLI from Exec mode.
exit command
Transpose a character at the cursor with a character to the left of the cursor.
Ctrl-t
Using the Interactive Help Feature
The question mark (?) character allows you to get the following type of help about the command at the command line. The following table lists the interactive help feature list.
Table 2 Interactive Help Feature List
Command
help
Provides a brief description of the Help feature in any command mode.
? at the command prompt
Lists all commands available for a particular command mode.
partial command?
Provides a list of commands that begin with the character string.
partial command<Tab>
Completes a partial command name.
command ?
Lists the keywords, arguments, or both associated with a command.
command keyword ?
Lists the arguments that are associated with the keyword.
Using the Help Command
Before You Begin
To look up keyboard commands, use the help command at the root level.
help
Help may be requested at any point in a command by entering a question mark ‘?’. If nothing matches, the help list will be empty and you must back up until entering a ‘?’ shows the available options. Two types of help are available
1. Full help is available when you are ready to enter a command argument (for example show ?) and describes each possible argument.
2. Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (for example show pr?).
Examples
Examples
> help
HELP:
Special keys:
DEL, BS... delete previous character
Ctrl-A .... go to beginning of line
Ctrl-E .... go to end of line
Ctrl-F .... go forward one character
Ctrl-B .... go backward one character
Ctrl-D .... delete current character
Ctrl-U, X. delete to beginning of line
Ctrl-K .... delete to end of line
Ctrl-W .... delete previous word
Ctrl-T .... transpose previous character
Ctrl-P .... go to previous line in history buffer
Ctrl-N .... go to next line in history buffer
Ctrl-Z .... return to root command prompt
Tab, <SPACE> command-line completion
Exit .... go to next lower command prompt
? .... list choices
Using the ? command
Before You Begin
To display all of the commands in your current level of the command tree, or to display more information about a particular command, use the ? command.
command name ?
When you enter a command information request, put a space between the command name and ?.
Examples
Examples
This command shows you all the commands and levels available from the root level.
> ?
clear Clear selected configuration elements.
config Configure switch options and settings.
debug Manages system debug options.
help Help
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
ping Send ICMP echo packets to a specified IP address.
reset Reset options.
save Save switch configurations.
show Display switch options and settings.
transfer Transfer a file to or from the switch.
Using the partial? command
Before You Begin
To provide a list of commands that begin with the character string, use the partial command ?.
partial command?
There should be no space between the command and the question mark.
Examples
Examples
This example shows how to provide a command that begin with the character string “ad”:
> controller> config>ad?
The command that matches with the string “ad” is as follows:
advanced
Using the partial command<tab>
Before You Begin
To completes a partial command name, use the partial command<tab> command.
partial command<tab>
There should be no space between the command and <tab>.
Examples
Examples
This example shows how to complete a partial command name that begin with the character string “ad”:
> Controller>config>cert<tab> certificate
Using the command ?
Examples
Examples
To list the keywords, arguments, or both associated with the command, use the command ?.
command ?
There should be space between the command and the question mark.
This example shows how to list the arguments and keyword for the command acl:
> Controller >config acl ?
Information similar to the following appears:
apply Applies the ACL to the data path.
counter Start/Stop the ACL Counters.
create Create a new ACL.
delete Delete an ACL.
rule Configure rules in the ACL.
cpu Configure the CPU Acl Information
command keyword ?
To list the arguments that are associated with the keyword, use the command keyword ?
command keyword ?
Usage Guidelines
There should be space between the keyword and the question mark.
Examples
Examples
This example shows how to display the arguments associated with the keyword cpu:
> controller>config acl cpu ?
Information similar to the following appears:
none None - Disable the CPU ACL
<name> <name> - Name of the CPU ACL