CleanAir Commands
Download this chapter
CleanAir CommandsCleanAir Commands
 Feedback

CleanAir Commands

ap dot11 24ghz cleanair

To enable CleanAir for detecting 2.4 GHz devices, use the ap dot11 24ghz cleanair command.

ap dot11 24ghz cleanair

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable CleanAir for 2.4 GHz devices 

Controller(config)#ap dot11 24ghz cleanair

ap dot11 24ghz cleanair alarm air-quality

To configure the alarm for the threshold value of air-quality for all 2.4-GHz devices, use the ap dot11 24ghz cleanair alarm air-quality command.

ap dot11 24ghz cleanair alarm air-quality threshold threshold _value

Syntax Description

air-quality

Configures the alarm for the air-quality of 2.4 GHz devices.

threshold threshold _value

Configures the threshold value for air-quality.

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to set the threshold value for the air-quality.

Controller(config)#ap dot11 24ghz cleanair alarm air-quality threshold 50

ap dot11 24ghz cleanair alarm device

To configure the alarm for the 2.4-GHz devices, use the ap dot11 24ghz cleanair alarm device command.

ap dot11 24ghz cleanair alarm device [ bt-discovery | bt-link | canopy | cont-tx | dect-like | inv | jammer | nonstd | superag | tdd-tx | video | wimax-fixed | wimax-mobile | xbox | zigbee ]

Syntax Description

alarm

Configure 2.4 GHz cleanair alarms.
device

Configures the 2.4 GHz cleanair interference devices alarm.

bt-discovery

Bluetooth Discovery.
bt-link

Bluetooth Link.
canopy

Canopy devices.

cont-tx

Continuous Transmitter.

dect-like

Digital Enhanced Cordless Communication (DECT) like phone.

fh

802.11 frequency hopping devices.
inv

Devices using spectrally inverted Wi-Fi signals.

jammer

Jammer.

nonstd

Devices using nonstandard Wi-Fi channels.

superag

802.11 SuperAG devices.

tdd-tx

TDD Transmitter.

video

Video cameras.

wimax-fixed

WiMax Fixed.

wimax-mobile

WiMax Mobile

xbox

Xbox.
zigbee

802.15.4 devices.

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable the alarm to notify interferences from a zigbee device.

Controller(config)#ap dot11 24ghz cleanair alarm device zigbee

ap dot11 24ghz cleanair device

To configure the 2.4-GHz interference devices to report to the controller, use the ap dot11 24ghz cleanair device command.

ap dot11 24ghz cleanair device { bt-discovery | bt-link | canopy | cont-tx | dect-like | inv | jammer | nonstd | superag | tdd-tx | video | wimax-fixed | wimax-mobile | xbox | zigbee }

Syntax Description

bt-discovery

Bluetooth Discovery.
bt-link

Bluetooth Link.
canopy

Canopy devices.

cont-tx

Continuous Transmitter.

dect-like

Digital Enhanced Cordless Communication (DECT) like phone.

fh

802.11 frequency hopping devices.
inv

Devices using spectrally inverted Wi-Fi signals.

jammer

Jammer.

nonstd

Devices using nonstandard Wi-Fi channels.

superag

802.11 SuperAG devices.

tdd-tx

TDD Transmitter.

video

Video cameras.

wimax-fixed

WiMax Fixed.

wimax-mobile

WiMax Mobile

xbox

Xbox.
zigbee

802.15.4 devices.

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable CleanAir to report when a video camera interferes.

Controller(config)#ap dot11 24ghz cleanair device video

ap dot11 24ghz rrm channel cleanair-event

To enable EDRRM for 2.4 GHz devices, use the ap dot11 24ghz rrm channel cleanair-event command. To disable EDRRM, use the no form of the command.

ap dot11 24ghz rrm channel cleanair-event sensitivity { high | low | medium }

no ap dot11 24ghz rrm channel cleanair-event sensitivity { high | low | medium }

Syntax Description

cleanair-event

Enables EDRRM cleanair event-driven RRM parameters

Command Default

None.

Command Modes

Interface configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

None.

This example shows how to set EDRRM sensitivity to low.

Controller#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Controller(config)#ap dot11 24ghz rrm channel cleanair-event sensitivity low

ap dot11 24ghz rrm channel device

To configure persistent non Wi-Fi device avoidance in the 802.11b channel assignment, use the ap dot11 24ghz rrm channel device command. To disable persistent device avoidance, use the no form of the command.

ap dot11 24ghz rrm channel device

no ap dot11 24ghz rrm channel device

Syntax Description

device

Configures persistent non Wi-Fi device avoidance in the 802.11b channel assignment.

Command Default

None.

Command Modes

Interface configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

None.

This example shows how to enable PDA.

Controller#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Controller(config)#ap dot11 24ghz rrm channel device

ap dot11 5ghz cleanair

To enable CleanAir for detecting 5GHz devices, use the ap dot11 5ghz cleanair command.

ap dot11 5ghz cleanair

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable CleanAir for 5 -GHz devices.

Controller(config)#ap dot11 5ghz cleanair

ap dot11 5ghz cleanair alarm air-quality

To configure the alarm for the threshold value of air-quality for all 5-GHz devices, use the ap dot11 5ghz cleanair alarm air-quality command.

ap dot11 5ghz cleanair alarm air-quality threshold threshold _value

Syntax Description

air-quality

Configures the alarm for the air-quality of 5 GHz devices.

threshold threshold _value

Configures the threshold value for air-quality.

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to set the threshold value for the air-quality.

Controller(config)#ap dot11 5ghz cleanair alarm air-quality threshold 30

ap dot11 5ghz cleanair alarm device

To configure the alarm for the 5-GHz devices, use the ap dot11 5ghz cleanair alarm device command.

ap dot11 5ghz cleanair alarm device [ canopy | cont-tx | dect-like | inv | jammer | nonstd | radar | superag | tdd-tx | video | wimax-fixed | wimax-mobile ]

Syntax Description

alarm

Configure 2.4 GHz cleanair alarms.
device

Configures the 2.4 GHz cleanair interference devices alarm.

canopy

Canopy devices.

cont-tx

Continuous Transmitter.

dect-like

Digital Enhanced Cordless Communication (DECT) like phone.

inv

Devices using spectrally inverted Wi-Fi signals.

jammer

Jammer.

nonstd

Devices using nonstandard Wi-Fi channels.

radar

Radars.
superag

802.11 SuperAG devices.

tdd-tx

TDD Transmitter.

video

Video cameras.

wimax-fixed

WiMax Fixed.

wimax-mobile

WiMax Mobile

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable the alarm to notify interferences from a radar device.

Controller(config)#ap dot11 5ghz cleanair alarm device radar

ap dot11 5ghz cleanair device

To configure the 5-GHz interference devices to report to the controller, use the ap dot11 5ghz cleanair device command.

ap dot11 5ghz cleanair device { canopy | cont-tx | dect-like | inv | jammer | nonstd | radar | superag | tdd-tx | video | wimax-fixed | wimax-mobile }

Syntax Description

canopy

Canopy devices.

cont-tx

Continuous Transmitter.

dect-like

Digital Enhanced Cordless Communication (DECT) like phone.

inv

Devices using spectrally inverted Wi-Fi signals.

jammer

Jammer.

nonstd

Devices using nonstandard Wi-Fi channels.

radar

Radar.
superag

802.11 SuperAG devices.

tdd-tx

TDD Transmitter.

video

Video cameras.

wimax-fixed

WiMax Fixed.

wimax-mobile

WiMax Mobile

Command Default

Disabled

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Enable CleanAir first to be able to use the other commands within it.

This example shows how to enable CleanAir to report when a video camera interferes.

Controller(config)#ap dot11 5ghz cleanair device video

ap dot11 5ghz rrm channel cleanair-event

To enable EDRRM for 5-GHz devices, use the ap dot11 5ghz rrm channel cleanair-event command. To disable EDRRM, use the no form of the command.

ap dot11 5ghz rrm channel cleanair-event sensitivity { high | low | medium }

no ap dot11 5ghz rrm channel cleanair-event sensitivity { high | low | medium }

Syntax Description

cleanair-event

Enables EDRRM cleanair event-driven RRM parameters

Command Default

None.

Command Modes

Interface configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

None.

This example shows how to set the EDRRM sensitivity to high.

Controller#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Controller(config)#ap dot11 5ghz rrm channel cleanair-event sensitivity high

ap dot11 5ghz rrm channel device

To configure persistent non Wi-Fi device avoidance in the 802.11a channel assignment, , use the ap dot11 5ghz rrm channel device command. To disable PDA, use the no form of the command.

ap dot11 5ghz rrm channel device

no ap dot11 5ghz rrm channel device

Syntax Description

cleanair-event

Configures persistent non Wi-Fi device avoidance in the 802.11a channel assignment.

Command Default

None.

Command Modes

Interface configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

None.

This example shows how to enable PDA for 802.11a devices.

Controller#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Controller(config)#ap dot11 5ghz rrm channel device

show ap dot11 24ghz cleanair device type

To display the 2.4 GHz interference devices, use the show ap dot11 24ghz cleanair device type command.

show ap dot11 24ghz cleanair device type { all | bt-discovery | bt-link | canopy | cont-tx | dect-like | fn | inv | jammer | mv-oven | nonstd | persistent | superag | tdd-tx | video | winmax-fixed | wimax-mobile | xbox | zigbee }

Syntax Description

all

Displays all CleanAir Interferers for 2.4GHz band.

bt-discovery

Displays CleanAir Interferers of type BT Discovery for 2.4GHz band.

bt-link

Displays CleanAir Interferers of type BT Link for 2.4GHz band.

canopy

Displays CleanAir Interferers of type Canopy for 2.4GHz band.

cont-tx

Displays CleanAir Interferers of type Continuous TX for 2.4GHz band.

dect-like

Displays CleanAir Interferers of type DECT Like for 2.4GHz band.

fh

Displays CleanAir Interferers of type 802.11FH for 2.4GHz band.

inv

Displays CleanAir Interferers of type WiFi Inverted for 2.4GHz band.

jammer

Displays CleanAir Interferers of type Jammer for 2.4GHz band.

mv-oven

Displays CleanAir Interferers of type MW Oven for 2.4GHz band.

nonstd

Displays CleanAir Interferers of type WiFi Inv. Ch for 2.4GHz band.

persistent

Displays CleanAir Interferers of type Persistent for 2.4GHz band.

superag

Displays CleanAir Interferers of type SuperAG for 2.4GHz band.

tdd-tx

Displays CleanAir Interferers of type TDD Transmit for 2.4GHz band.

video

Displays CleanAir Interferers of type Video Camera for 2.4GHz band.

winmax-fixed

Displays CleanAir Interferers of type WiMax Fixed for 2.4GHz band.

wimax-mobile

Displays CleanAir Interferers of type WiMax Mobile for 2.4GHz band.
xbox

Displays CleanAir Interferers of type Xbox for 2.4GHz band.

zigbee

Displays CleanAir Interferers of type zigbee for 2.4GHz band.

Command Default

None.

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Interference devices will be listed only if there is an interference from any 2.4-GHz devices.

This example shows how to view all the 2.4-GHz interference devices.

Controller#show ap dot11 24ghz cleanair device type all

DC    = Duty Cycle (%)
ISI   = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID

No    ClusterID          DevID  Type           AP Name                 ISI  RSSI  DC   Channel
-------------------------------------------------------------------------------------------------

show ap dot11 5ghz cleanair device type

To display the 5 GHz interference devices, use the show ap dot11 5ghz cleanair device type command.

show ap dot11 5ghz cleanair device type { all | canopy | cont-tx | dect-like | inv | jammer | nonstd | persisten | superag | tdd-tx | video | wimax-fixed | wimax-mobile }

Syntax Description

all

Displays all CleanAir Interferers for 2.4GHz band.

canopy

Displays CleanAir Interferers of type Canopy for 2.4GHz band.

cont-tx

Displays CleanAir Interferers of type Continuous TX for 2.4GHz band.

dect-like

Displays CleanAir Interferers of type DECT Like for 2.4GHz band.

inv

Displays CleanAir Interferers of type WiFi Inverted for 2.4GHz band.

jammer

Displays CleanAir Interferers of type Jammer for 2.4GHz band.

nonstd

Displays CleanAir Interferers of type WiFi Inv. Ch for 2.4GHz band.

persistent

Displays CleanAir Interferers of type Persistent for 2.4GHz band.

superag

Displays CleanAir Interferers of type SuperAG for 2.4GHz band.

tdd-tx

Displays CleanAir Interferers of type TDD Transmit for 2.4GHz band.

video

Displays CleanAir Interferers of type Video Camera for 2.4GHz band.

winmax-fixed

Displays CleanAir Interferers of type WiMax Fixed for 2.4GHz band.

wimax-mobile

Displays CleanAir Interferers of type WiMax Mobile for 2.4GHz band.

Command Default

None

Command Modes

Global configuration.

Command History

Release Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Interference devices will be listed only if there is an interference from any 5 GHz devices.

This example shows how to view all the 5 GHz interference devices.

Controller#show ap dot11 5ghz cleanair device type all

DC    = Duty Cycle (%)
ISI   = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID

No    ClusterID          DevID  Type           AP Name                 ISI  RSSI  DC   Channel
-------------------------------------------------------------------------------------------------