Call Control Profile
Configuration Mode
Call Control
Profile configuration mode defines call-handling rules which can
be combined with other profiles – such as an APN profile
(see the APN Profile Configuration
Mode Commands chapter) – when using the Operator Policy
feature. The call control profile is a key element in the Operator
Policy feature and the profile is not valid until it is associated
with an operator policy (see the associate command
in the Operator Policy
Configuration Mode Commands chapter).
The MME and SGSN each
support a maximum of 1,000 call control profiles; only one profile
can be associated with an operator policy.
By configuring a call
control profile, the operator fine tunes any desired restrictions
or limitations needed to control call handling per subscriber or
for a group of callers across IMSI (International Mobile Subscriber
Identity) ranges.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
IMPORTANT:
The commands or keywords/variables
that are available are dependent on platform type, product version,
and installed license(s).
access-restriction-data
Enables the operator
to assign a failure code to be included in reject messages if the
attach rejection is due to access restriction data (ARD) checking
in the incoming subscriber data (ISD) messages. The operator can
also disable the ARD checking behavior.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
access-restriction-data { eutran-not-allowed | failure-code cause_code | no-check }remove access-restriction-data { failure-code | eutran-not-allowed }
remove
Removes the failure
code setting
or eutran-not-allowed
override setting.
eutran-not-allowed
Overrides the eutran-not-allowed
flag received in ISD/ULA messages from the HLR/HSS received
during the Attach process. The overridden value will be sent to
the RNC during PDP context activation (in RAB Assignment Request
messages) so that the RNC subsequently avoids performing a handover
to E-UTRAN. Configuration of the eutran-not-allowed parameter
is valid only if SRNS relocation first has been configured in Call Control Profile
Configuration Mode via the srns-inter and/or srns-intra commands.
The call-control-profile then must be associated with an operator
policy in Operator Policy Configuration
Mode using the associate command.
Once the operator policy is associated with the call-control-profile,
inclusion of the E-UTRAN Service Handover Information Element in
RAB Assignment Request and Relocation Request RANAP messages must
be enabled. This is done by executing the ranap eutran-service-handover-ie command
in RNC Configuration
Mode.
failure-code cause_code
cause_code:
Enter an integer from 2 through 111; default code is 13 (roaming
not allowed in this location area [LA]).
Refer to the GMM failure
cause codes listed below (from section 10.5.5.14 of the 3GPP TS 124.008
v7.2.0 R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 -MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
no-check
Including this keyword
with the command disables the ARD checking behavior.
Usage:
By default, the SGSN
checks access restriction data (ARD) within incoming insert subscriber
data (ISD) messages. This enables operator to selectively restrict
subscribers in either 3G (UTRAN) or 2G (GERAN). The SGSN ARD checking
behavior occurs during the attach procedure and if a reject occurs,
the SGSN sends the subscriber an Attach Reject message with a configurable
failure cause code.
Example:
For this call control
profile, the following command disables the ARD checking function:
access-restriction-data
no-check
accounting context
Defines the name of
the accounting context and optionally associates a GTPP group with this
call control profile.
Product:
ePDG
S-GW
SAEGW
SGSN
SaMOG
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
accounting context ctxt_name [ aaa-group grp_name ] [ gtpp group grp_name ] remove accounting
context [ aaa-group | gtpp ]
remove
Removes the accounting
configuration from this profile’s configuration.
ctxt_name
Specifies the accounting
context as an alphanumeric string of 1 through 79 characters.
aaa-group grp_name
Configures AAA Group
for MRME .
grp_nameis
a string of 1 to 63 characters (any combination of letters and digits)
to identify the aaa-group created with the aaa-group command
in the Context configuration mode.
gtpp group grp_name
Identifies the GTPP
group, where the GTPP related parameters have been configured in
the GTPP Group Configuration mode, to associate with this call control
profile.
grp_nameis
a string of 1 to 63 characters (any combination of letters and digits)
to identify the GTPP group created with the gtpp group command
in the Context configuration mode.
Usage:
This command can be
used to associate a predefined GTPP server group - including all
its associated configuration - with a specific call control profile.
The GTPP group would have been defined with the gtpp group command
(see the Context Configuration
Mode Commands chapter).
If the GTPP group
is not specified, then a default GTPP group in the accounting context will
be used.
If this command is
not specified, use the name of the accounting context configured
in the SGSN service configuration mode (for 3G) or the GPRS service
configuration mode (for 2G), either will automatically use a “default” GTPP
group generated in that accounting context.
If the accounting
context is specified in the GPRS service or SGSN service and in
a call control profile, the priority is given to the accounting
context of the call control profile.
Example:
For this call control
profile, the following command identifies an accounting context
called
acctng1 and
associates a GTPP server group named
roamers with
defined charging gateway accounting functionality.
accounting context
acctng1 gtpp group roamers
accounting mode
Configures the mode
to be used for accounting – GTPP (default), RADIUS/Diameter
or None.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
accounting mode { gtpp | none | radius-diameter }remove accounting mode
remove
Removes the accounting
mode.
gtpp
Specifies that GTPP
accounting is performed. This is the default method.
none
Specifies that no accounting
will be performed for the call control profile.
radius-diameter
Specifies that RADIUS/Diameter
will be performed for the call control profile.
Usage:
Use this command to
specify the accounting mode for a call control profile. For additional information
on accounting mode and its relationship to operator policy, refer
to the System Administration
Guide.
Example:
The following command
specifies that RADIUS/Diameter accounting will be used
for the call control profile:
accounting mode radius-diameter
accounting stop-trigger
Configures the trigger
point for accounting stop CDR. Default is on session deletion request.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
accounting stop-trigger
customdefault accounting stop-trigger
default
Accounting stop CDR
triggered once Delete Session/Delete Bearer Request is
received at S-GW.
custom
Accounting stop CDR
triggered once Delete Session/Delete Bearer Response is
received at S-GW.
Usage:
Use this command to
specify the trigger point for accounting stop CDR for a call control
profile.
Example:
The following command
specifies that accounting stop trigger would be at response of session
deletion:
accounting stop-trigger custom
allocate-ptmsi-signature
Enables or disables
the allocation of a P-TMSI (Packet Temporary Mobile Subscriber Identity)
signature.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no | default ] allocate-ptmsi-signature
no
Disables the allocation
of the P-TMSI signature.
default
Resets the configuration
value to the default, which is to allocate the P-TMSI signature.
Usage:
Use this command to
enable or disable the allocation of the P-TMSI signature.
apn-restriction
Enables the APN restriction
feature and configures the instruction for the SGSN on the action
to take when an APN restriction value is received from the GGSN
during an Update PDP Context procedure.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
apn-restriction update-policy
deactivate restrictiondefault apn-restriction
default
Creates a default
APN restriction configuration.
update-policy deactivate restriction
Specifies one of the
two restriction types to define the appropriate action if the APN
restriction value received conflicts with the stored value:
-
least-restrictive set
the least restrictive value applicable when there are no already
active PDP context(s).
-
most-restrictive sets
the most stringent restriction required by any already active PDP
context(s).
Usage:
When this feature is
enabled, the SGSN will send the maximum APN restriction value in every
CPC Request message sent to the GGSN. The SGSN expects to receive
an APN restriction value in each PDP Context received from the GGSN.
The SGSN stores and compares received APN restriction values to
check for conflicts. In the case of a conflict, the SGSN rejects the
PDP Context with appropriate messages and error codes to the MS.
If an APN restriction
value is not assigned by the GGSN, the SGSN assumes the value of “1” (least
restrictive) to allow APN restriction rules will be possible when
valid values are assigned for new PDP Context(s) from the same MS.
Example:
The following command
applies the lowest level of APN restrictions:
apn-restriction update-policy
deactivate least-restrictive
associate
Associates various
MME -specific lists and databases with this call control profile. On an SGSN, this command
can be used to associate some of these MME-related items to GPRS
and/or SGSN services in support of S4 functionality.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
associate { ho-restrict-list list_name | hss-peer-service service_name [ s13-interface | s6a-interface | s13-prime-interface | s6d-interface ] | tai-mgmt-db tai-db_name }remove associate { ho-restrict-list | hss-peer-service [ s13-interface | s6a-interface | s13-prime-interface | s6d-interface ] | tai-mgmt-db }
remove
Remove the specified
association definition from the call control profile.
ho-restrict-list list_name
MME
only.
Identifies the handover
restriction list that should be associated with this call control
profile.
list_name is
a string of 1 to 64 characters (any combination of letters and digits).
hss-peer-service service_name
Associates a home
subscriber server (HSS) peer service with this call control profile.
service_name is
an existing HSS peer service expressed as a string of 1 to 63 characters
(any combination of letters and digits).
[ s13-interface | s6a-interface | s13-prime-interface | s6d-interface ]
Optionally, identify
the interface to be associated with the HSS service in this call
control profile.
The s13-interface and
the s6a-interface options
apply to the MME only.
The s13-prime-interface and s6d-interface options
apply to the SGSN only.
The s6d-interface is
used by the SGSN to communicate with the HSS. It is a Diameter-based
interface which supports location management, subscriber data handling
, authentication , and fault recovery procedures.
The s13-prime-interface is
used by the SGSN to communicate with the equiprement identity register
(EIR). It is a Diameter-based interface which performs the mobile
equipment (ME) identity check procedure.
IMPORTANT:
The s13-prime-interface can
only be used if an s6d-interface is
configured.
tai-mgmt-db tai-db_name
Identifies the tracking
area identifier (TAI) database that should be associated with this
call control profile.
tai-db_name is
a string of 1 to 64 characters (any combination of letters and digits).
This configuration overrides
the S-GW selection and TAI list assignment functionality for a call
that uses an operator policy associated with this call control profile.
The TAI management object provides a TAI list for calls and provides
S-GW selection functionality if a DNS is not configured for S-GW
discovery for this operator policy or if a DNS discovery fails.
If a TAI management database
is associated with a call-control-profile, and if DNS is used for
S-GW lookups, then the DNS configuration for S-GW lookups must also
be configured within the same call-control-profile using the dns-sgw command
in the call-control-profile configuration mode.
On the S4-SGSN, use
this option to associate a locally configured S-GW address for the RAI
address for selection if operators wish to bypass DNS resolution
of RAI FQDN. This option is valid only after the following commands
have been executed on the S4-SGSN:
-
The
tai-mgmt-db command
in
LTE Policy Configuration
Mode
-
The
tai-mgmt-obj command
in
LTE TAI Management
Database Configuration Mode.
-
The
tai and
sgw-address commands
in
LTE TAI Management
Object Configuration Mode.
Usage:
Use this command to
associate handover restriction lists, HSS service (and interfaces),
and a TAI database with the call control profile. This ensures that
the information is available for application when a Request is received.
Repeat the command as
needed to associate each feature.
Example:
Link HO restriction
list named
HOrestrict1 with
this call control profile:
associate ho-restrict-list HOrestrict1
The following command
associates this SaMOG call control profile with an accounting policy
called acct1:
attach access-type
Defines attach-related
configuration parameters for this call control profile based on
the access-type (GPRS, UMTS, or both) and location area list.
IMPORTANT:
SGSN only: Before
using this command, ensure that the appropriate location area code
(LAC) information has been defined via the location-area-list command.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
attach access-type { gprs | umts } { all | location-area-list
instance list_id } { failure-code code | user-device-release { before-r99 failure
code code | r99-or-later
failure code code } } default attach access-type { eps | gprs | umts } { all | location-area-list
instance list_id } { failure-code | user-device-release { before-r99
failure code | r99-or-later failure code }
default
Restores the default
values for the for the specified parameter.
access-type type
Defines the type of
access to be allowed or restricted.
all
Instructs the SGSN
or MME to apply the command action to all location area lists. Location area
lists should already have been created with the location-area-list command.
The location area list consists of one or more LACs, location area codes,
where the MS is when placing the call.
location-area-list
instance list_id
Instructs the SGSN
to apply the command action to a specific location area list. Location area
lists should already have been created with the location-area-list command.
The location area list consists of one or more LACs, location area codes,
where the MS is when placing the call.
Using this keyword
with either the allow or restrict keywords
enables you to configure with more granularity.
list_id:
Enter an integer between 1 and 5.
failure-code code
Specify a GMM failure
cause code to identify the reason an attach did not occur. This
GMM cause code will be sent in the reject message to the MS.
Default: 14.
fail-code:
Enter an integer from 2 to 111. Refer to the GMM failure cause codes
listed below (from section 10.5.5.14 of the 3GPP TS 124.008 v7.2.0
R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 -MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
Note:
It is mandatory to enable the command attach restrict
access-type gprs all so that the failure code is saved
after a re-boot. The attach access-type gprs all failure-code
< code > command and the attach restrict access-type
gprs all command work together and have to be enabled together.
user-device-release { before-r99 | r99-or-later } failure-code code
Default: disabled
Enables the SGSN to
reject an Attach procedure based on the detected 3GPP release version of
the MS equipment and selectively send a failure cause code in the
reject message. The SGSN uses the following procedure to implement
this configuration:
-
When Attach Request
is received, the SGSN checks the subscriber’s IMSI and
current location information.
-
Based on the IMSI,
an operator policy and call control profile are found that relate
to this Attach Request.
-
Profile is checked
for access limitations.
- Attach Request is
checked to see if the revision indicator bit is set
-
if not, then the configured
common failure code for reject is sent;
-
if set, then the 3GPP
release level is verified and action is taken based on the configuration
of this parameter
One of the following
options must be selected and completed:
-
before-r99:
Indicates the MS would be a 3GPP release prior to R99 and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
-
r99-or-later :
Indicates the MS would be a 3GPP Release 99 or later and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
Usage:
Once the IMSI of an
incoming call is known and matched with a specific operator policy, according
to the filter definition of the mcc command,
then the associated call control profile is selected to determine
how the incoming call is handled.
By default, all attaches
are allowed. If no access limitations are needed, do not use the attach command.
IMPORTANT:
Before using this
command, ensure that the appropriate LAC information has been defined with
the location-area-list command.
Use this command to
define attach limitations for the call control profile.
Use this command to
fine-tune the attach configuration specifying which calls/subscribers can
attach and which calls are restricted from attaching and what failure
code is included in the Reject message.
Attachment restrictions
can be based on any one or combination of the options, such as location
area code or access type. It is even possible to restrict all attaches.
The command can be
repeated using different keyword values to further fine-tune the attachment
configuration.
Related Commands
- Use the attach restrict command
to restrict attaches.
- Use the attach allow command
to re-enable restrictions after an attach restrict command
has been used.
Example:
The following example
sets all restrictions for access-type gprs and specified release
version to the default setting.
default attach access-type
gprs all user-device-release before-r99 failure-code
attach allow
Configures the system
to re-enable attaches that were previously restricted using the attach restrict command..
IMPORTANT:
SGSN only: Before
using this command, ensure that the appropriate location area code
(LAC) information has been defined via the location-area-list command.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no ] attach
allow access-type { eps | gprs | umts } location-area-list
instance list_id
no
Deletes the specified
attach configuration.
allow
Enables attaches in
the configuration after an attach restrict command
has been used.
access-type type
Defines the type of
access to be allowed.
location-area-list
instance list_id
Instructs the SGSN
to apply the command action to a specific location area list. Location area
lists should already have been created with the location-area-list command.
The location area list consists of one or more LACs, location area codes,
where the MS is when placing the call.
list_id:
Enter an integer between 1 and 5.
Usage:
Once the IMSI of an
incoming call is known and matched with a specific operator policy, according
to the filter definition of the mcc command,
then the associated call control profile is selected to determine
how the incoming call is handled.
By default, all attaches
are allowed. If no access limitations are needed, then do not use
the attach command.
IMPORTANT:
Before using this
command, ensure that the appropriate LAC information has been defined with
the location-area-list command.
Use this command to
define attach limitations for the call control profile.
Use this command to
fine-tune the attach configuration specifying which calls/subscribers can
attach and which calls are restricted from attaching and what failure
code is included in the Reject message.
Attachment restrictions
can be based on any one or combination of the options, such as location
area code or access type. It is even possible to restrict all attaches.
The command can be
repeated using different keyword values to further fine-tune the attachment
configuration.
Related Commands
- Use the attach access-type command
to define the type of access to restrict or allow.
- Use the attach restrict command
to restrict attaches.
Example:
For calls under the
purview of this call control profile, the following command allows attaches
of
all subscribers
using the GPRS access type.
attach allow access-type
gprs all
attach imei-query-type
Defines device Attach
limitations for this call control profile if an IMEI is not already
present in the Attach Request.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
attach imei-query-type { imei | imei-sv | none } [ verify-equipment-identity [ allow-on-eca-timeout | deny-greylisted | deny-unknown | verify-emergency ] + ] remove attach imei-query-type
remove
Deletes the specified
attach configuration.
imei-query-type { imei | imei-sv | none }
Configures system behavior
during Attach procedures if an IMEI is not already present in the
Attach Request.
-
imei: Specifies
that the system is required to query the UE for its International
Mobile Equipment Identity (IMEI).
-
imei-sv: Specifies
that the system is required to query the UE for its International
Mobile Equipment Identity - Software Version (IMEI-SV).
-
none: Specifies
that the system does not need to query for IMEI or IMEI-SV.
verify-equipment-identity [ allow-on-eca-timeout | deny-greylisted | deny-unknown | verify-emergency ]
Specifies that the identification
(IMEI or IMEI-SV) of the UE is to be performed by the Equipment
Identity Register (EIR) over the S13 interface.
-
allow-on-eca-timeout:
Configures the MME to allow equipment that has timed-out on ECA
during the attach procedure.
-
deny-greylisted:
Configures the MME to deny grey-listed equipment during the attach
procedure.
-
deny-unknown:
Configures the MME to deny unknown equipment during the attach procedure.
-
verify-emergency:
Configures the MME to ignore the IMEI validation of the equipment
during the attach procedure in emergency cases. This keyword is
only supported in release 12.2 and higher.
Usage:
Configures system
settings related to the UE Attach procedure for the specified call control
profile
The command can be
repeated using different keyword values to further fine-tune the attachment
configuration.
Example:
The following command
configures the system to query the UE for its IMEI and to verify the
UE equipment identity with an Equipment
attach imei-query-type
imei verify-equipment-identity
attach restrict
Configures the system
to restrict attaches based on access type and location areas (either all
or specified location area list) for this call control profile.
IMPORTANT:
SGSN only: Before
using this command, ensure that the appropriate location area code
(LAC) information has been defined via the location-area-list command.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no ] attach
restrict access-type { eps [ emm-cause-code code | imsi-attach-fail [ emm-cause-code code ] | voice-unsupported [ emm-cause-code code ] ] | gprs | umts } { all | location-area-list
instance list_id }
no
Deletes the specified
attach configuration.
access-type type
Defines the type of
access to be allowed or restricted.
emm-cause-code code
Specifies the EPS Mobility
Management (EMM) cause code to return to the UE:
-
eps-service-disallowed
-
eps-service-not-allowed-in-this-plmn
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
The default cause code
is no-suitable-cell-in-tracking-area.
IMPORTANT:
The tracking-area-not-allowed cause
code is not supported for the MME.
IMPORTANT:
The roaming-not-allowed-in-this-tracking-area and tracking-area-not-allowed cause
codes are not applicable for use with the imsi-attach-fail or voice-unsupported keywords.
imsi-attach-fail
Directs the MME to restrict
EPS attach when IMSI attach fails. If the policy is configured, all
IMSI failures will result in a EPS restriction.
The default cause code
for calls rejected for imsi-attach-fail is no-suitable-cell-in-tracking-area.
voice-unsupported
Directs the MME to restrict
EPS attach when voice is not supported, such as when Voice over
IMS is not supported and the UE does not support Circuit Switched
Fall Back (CSFB).
This setting is applicable
when all of the following conditions apply:
- The UE is voice-centric
as determined in the UE usage setting of the Voice Domain and UE
Settings IE sent in the request.
- The UE does not support
CSFB as determined in the EMM Combined procedures Capability bit
of the MS Network Capability IE sent in the request, OR if CSFB
is not supported on the MME as determined by the SGs service not
being associated with the MME service.
- Voice over IMS is not
supported in the network as defined by the network-feature-support-ie
ims-voice-over-ps command.
The default cause code
for calls rejected for voice-unsupported is no-suitable-cell-in-tracking-area.
all
Instructs the system
to apply the command action to all location area lists. Location
area lists should already have been created with the location-area-list command.
The location area list consists of one or more LACs, location area codes,
where the MS is when placing the call.
location-area-list
instance list_id
Instructs the SGSN
to apply the command action to a specific location area list. Location area
lists should already have been created with the location-area-list command.
The location area list consists of one or more LACs, location area codes,
where the MS is when placing the call.
Using this keyword
with either the allow or restrict keywords
enables you to configure with more granularity.
list_id:
Enter an integer between 1 and 5.
IMPORTANT:
This keyword only applies
to the SGSN.
Usage:
Once the IMSI of an
incoming call is known and matched with a specific operator policy, according
to the filter definition of the mcc command,
then the associated call control profile is selected to determine
how the incoming call is handled.
By default, all attaches
are allowed. If no access limitations are needed, then do not use
the attach command.
IMPORTANT:
Before using this
command, ensure that the appropriate LAC information has been defined with
the location-area-list command.
Use this command to
restrict attaches for the call control profile.
Use this command to
fine-tune the attach configuration specifying which calls/subscribers can
attach and which calls are restricted from attaching and what failure
code is included in the Reject message.
Attachment restrictions
can be based on any one or combination of the options, such as location
area code or access type. It is even possible to restrict all attaches.
The command can be
repeated using different keyword values to further fine-tune the attachment
configuration.
Related Commands
- Use the attach access-type command
to define the type of access to restrict or allow. The command attach
restrict access-type gprs all has to be enabled
, if the command attach access-type gprs all failure-code
< code > is used to define a failure code. The failure
code is saved after a re-boot only when the command attach restrict
access-type gprs all is enabled.
- Use the attach allow command
to re-enable restrictions after an attach restrict command
has been used.
Example:
For calls under the
purview of this call control profile, the following command restricts
the attaches of
all subscribers
using the GPRS access type.
attach restrict access-type
gprs all
To change the attach
restriction to only restrict attaches of GPRS subscribers from specified LACs
included in location area list #2 and include failure-code
45 as the reject cause. This configuration requires two CLI commands:
attach restrict access-type
gprs location-area-list instance 2
attach access-type
gprs location-area-list instance 2 failure-code 45
In the case of a dual-access
SGSN, it is possible to also add a second definition to restrict attaches
of UMTS subscribers within the LACs included in location area list #3.
attach restrict access-type
UMTS location-area-list instance 3
Change the configuration
to allow attaches for GPRS access for all previously restricted LACs
- note that GPRS attaches would still be limited:
no attach restrict
access-type gprs all
Restrict (deny) all
GPRS attach requests (coming from any location area) and assign
a single failure code for the reject messages. This is a two command
process:
attach restrict access-type
gprs all
attach access-type grps
all failure-code 22
authenticate all-events
Allows the operator
to quickly define authentication procedures, based on limited parameters, for
all types of events.
Privilege:
Security Administrator, Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate all-events [ access-type { gprs | umts } | frequency frequency [ access-type { gprs | umts } ] ][ no | remove ] authenticate
all-events [ access-type { gprs | umts } ]
no
Disables the specified
authentication configuration in the call control profile.
remove
Removes the specified
authentication configuration from the call control profile configuration
file.
access-type type
One of the following
must be selected to identify the type of network access if the access-type keyword
is included in the command:
The access-type keyword
can be included with any of the other three keywords available with
the authenticate
all-events command.
frequency frequency
This keyword defines
1-in-N selective authentication for all types
of subscriber events. If the frequency is set for 12, then
the service skips authentication for the first 11 events and authenticates
on the 12th event.
frequency must
be an integer from 1 to 16.
Usage:
By default, authentication
is not performed for any subscriber events. Use this command
to enable authentication for all types of events at one time, such
as but not limited to: Activate Requests, Attach
Requests, Detach Requests, Service-Requests.
IMPORTANT:
For the SGSN, in releases 15.0
and forward, the authentication on activation functionality has
been removed so the SGSN will not authenticate on Activate Requests.
Example:
The following command
configures all authentication for all subscriber events to occur every
tenth time a specific type of event occurs (for example
every tenth time an Attach Request is received):
authenticate all-events
frequency 10
The following command
configures authentication for all Detach Requests and RAUs to occur
if the UE access-type is UMTS:
authenticate all-events
access-type umts
authenticate attach
Allows the operator
to define authentication for Attach procedures.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate attach
access-type { gprs | umts }authenticate attach
attach-type { combined | gprs-only } [ access-type { gprs | umts } | frequency frequency ] authenticate attach
frequency frequency [ access-type { gprs | umts } ]authenticate attach
inter-rat [ access-type { gprs | umts } | attach-type { combined | gprs-only } [ access-type { gprs | umts } | frequency frequency ] | frequency frequency [ access-type { gprs | umts } ][ no | remove ] authenticate
attach [ access-type { gprs | umts } | attach-type { combined | gprs-only } | inter-rat | attach-type { combined | gprs-only } ] [ access-type { gprs | umts } ] ]
no
Disables the defined
authentication procedures configured for Attach Requests from the
call control profile.
remove
Deletes the defined
authentication procedures for Attach Requests from the call control profile
configuration file.
access-type type
One of the following
must be selected to identify the type of network access if the access-type keyword
is included in the command:
attach-type
This keyword configures
the Attach authentication based on the type of attach requested. The attach-type must
be one of the following options:
-
combined:
Authenticates combined GPRS/IMSI Attaches.
-
gprs-only:
Authenticates GRPS Attaches only.
frequency frequency
This keyword defines
1-in-N selective authentication for this type of subscriber event
- Attach Request. If the frequency is set for 12, then the service
skips authentication for the first 11 events and authenticates on
the twelfth event.
frequency must
be an integer from 1 to 16.
inter-rat
Enables/disables
authentication for Inter-RAT Attaches.
Usage:
Authentication for
Attach is disabled by default. This command enables/disables authentication
for an Attach with a local P-TMSI or Attaches with an IMSI, which
will be authenticated to acquire the CK (cipher key) and the IK
(integrity key).
Example:
The following command
configures authentication to occur after every tenth attach event
for GPRS access.
authenticate attach
frequency 10 access-type gprs
The following command
disables authentication for Inter-RAT Attaches, use:
no authenticate attach
inter-rat
authenticate detach
Allows the operator
to enable and define authentication for Detach procedures.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate detach [ access-type
umts ] [ no | remove ] authenticate
detach [ access-type umts ]
no
Disables the defined
authentication procedures configured for Detach Requests from the
call control profile.
remove
Deletes the defined
authentication procedures for Detach Requests from the call control profile
configuration file.
access-type umts
Optionally, identifies
the type of network access if the access-type umts keywords
are included in the command. By default, access-type UMTS is assumed.
Usage:
Authentication for
Detach procedures is disabled by default. This command enables/disables
authentication for a Detach Request and allows the operator to limit
authentication based on the MS/UE access-type.
Example:
The following command
configures detach authentication to occur only for UMTS attached subscribers:
authenticate detach
access-type umts
The following command
disables authentication for all Detach Requests, use:
no authenticate detach
authenticate on-first-vector
Allows the operator
to enable the SGSN to begin MS authentication immediately after
receiving the first vector from the HLR.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate on-first-vectorremove authenticate
on-first-vector
remove
Removes the authenticate
on-first-vector definition from the configuration file and resets
the default behavior so that the SGSN waits to receive all vectors
before beginning authentication towards the MS.
Usage:
After an initial attach
request, some end devices restart themselves after waiting for the PDP
to be established. In such cases, the SGSN restarts and a large
number of end devices repeat their attempts to attach. The attach
requests flood the radio network, and if the devices timeout before
the PDP is established then they continue to retry, thus even more
traffic is generated.
To avoid the high traffic
levels during PDP establishment, the SGSN has been modified to reduce
the attach time, as much as possible, so that the devices can attach
and discontinue sending requests. The current enhancement is intended
to reduce the time needed to retrieve vectors over the GR interface
by allowing the operator to configure the SGSN to start authentication
towards the MS as soon as it receives the first vector from the
AuC/HLR. With the new command included in the configuration,
the SGSN begins the MS authentication process immediately after
receiving the first vector from the HLR while the SAI continues
in parallel.
Example:
Use the following
command to configure the SGSN to begin MS authentication immediately after
receiving the first vector from the AuC/HLR:
authenticate on-first-vector
Use the following
command to reset the default behavior, so that the SGSN waits to
receive all vectors requested in the SAI from the AuC/HLR
before begining authentication towards the MS:
remove authenticate
on-first-vector
authenticate rau
Enables or disables
and fine tunes authentication procedures for routing area updates
(RAUs)
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate rau [ access-type { gprs | umts } | frequency frequency [ access { gprs | umts } ] | periodicity duration [ access { gprs | umts } ] | update-type { combined-update | imsi-combined-update | periodic | ra-update } [ access-type { gprs | umts } | frequency frequency | periodicity duration | with { foreign-ptmsi | inter-rat-local-ptmsi | local-ptmsi } [ access-type { gprs | umts } | frequency frequency | periodicity duration ] no authenticate rau [ access-type { grps | umts } | update-type { combined-update | imsi-combined-update | periodic | ra-update } [ access-type { gprs | umts } | with { foreign-ptmsi | inter-rat-local-ptmsi | local-ptmsi } [ access-type { gprs | umts } ] remove authenticate
rau [ access-type { gprs | umts } | periodicity [ access { gprs | umts } ] | update-type { combined-update | imsi-combined-update | periodic | ra-update } [ access-type { gprs | umts } | periodicity | with { foreign-ptmsi | inter-rat-local-ptmsi | local-ptmsi } [ access-type { gprs | umts } | periodicity ] ]
no
Disables authentication
for the RAUs specified in the configuration for the call control profile.
remove
Deletes the authentication
configuration for the RAUs from the call control profile in the configuration
file.
access-type type
One of the following
must be selected to identify the type of network access if the access-type keyword
is included in the command:
The access-type keyword
can be included with any of the other keywords available with the authenticate rau command.
frequency frequency
Defines 1-in-N selective
authentication for RAU events. If the frequency is set for 12, then the
SGSN skips authentication for the first 11 events and authenticates
on the twelfth event.
frequency must
be an integer from 1 to 16.
periodicity duration
Defines the length
of time (number of minutes) that authentication can be skipped.
duration:
Must be an integer from 1 to 10800.
update-type
Defines the type of
RAU Request. Select one of the following:
-
combined-update [ access-type | with
inter-rat-local-ptmsi ]
-
imsi-combined-update [ access-type | with
inter-rat-local-ptmsi ]
-
periodic [ access-type | frequency | periodicity ]
-
ra-update [ access-type | with
inter-rat-local-ptmsi ]
Usage:
By default, authentication
is not performed for routing area updates (RAUs). Use this command
to enable/disable authentication and to fine tune the authentication
procedure based on frequency, periods for skipping authentication
and the various types of routing area updates.
Example:
The following command
configures RAU authentication to occur after every tenth event for GPRS
access.
authenticate rau frequency
10 access-type gprs
The following command
disables authentication for RAUs based on the combined IMSI with
foreign P-TMSIs, use:
no authenticate rau
imsi-combined-update with foreign-ptmsi
The following command
deletes all authentication configuration from the call control profile for
all RAUs using GPRS access-type:
remove authenticate
rau access-type gprs
authenticate service-request
Enables or disables
and fine-tunes authentication procedures for Service Requests.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate service-request [ frequency frequency | periodicity duration | service-type { data | page-response | signaling } [ frequency frequency | periodicity duration ] ]no authenticate service-request [ service-type { data | page-response | signaling } ] remove authenticate
service-request [ periodicity | service-type { data | page-response | signaling } [ periodicity ] ]
no
Disables authentication
for the Service Requests specified in the configuration for the
call control profile.
remove
Deletes the authentication
configuration for Service Requests from the call control profile
in the configuration file.
frequency frequency
Defines 1-in-N selective
authentication for this type of subscriber event - Service Request.
If the frequency is set for 12, then the service skips authentication
for the first 11 events and authenticates on the twelfth event.
frequency must
be an integer from 1 to 16.
periodicity duration
Defines the length
of time (number of minutes) that authentication can be skipped.
duration:
Must be an integer from 1 to 10800.
signaling-type
Defines the type of
service being requested by the Service Request. Select one of the following:
Usage:
By default, authentication
is not performed for Service Requests. Use this command to enable/disable
authentication and to fine-tune the authentication procedure based
on frequency and periods for skipping authentication and the various
types of service. Repeat the commands as needed to configure criteria
for all service types.
Example:
The following command
configures authentication Service Requests for data service to only occur
every 5 minutes:
authenticate service-request
service-type data periodicity 5
authenticate sms
Enables or disables
and fine tunes authentication procedures for Short Message Service
(SMS).
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate sms [ access-type { gprs | umts } | frequency frequency [ access-type { gprs
umts } ] | sms-type { mo-sms | mt-sms } [ access-type { gprs | umts } | frequency frequency ] ][ no | remove ] authenticate
sms [ access-type { gprs | umts } | sms-type { mo-sms | mt-sms } [ access-type { gprs umts } ] ]
no
Disables authentication
for the SMS Requests specified in the configuration for the call control
profile.
remove
Deletes the authentication
configuration for SMS Requests from the call control profile in the
configuration file.
access-type type
One of the following
must be selected to identify the type of network access if the access-type keyword
is included in the command:
The access-type keyword
can be included with any of the other keywords available with the authenticate sms command.
frequency frequency
Defines 1-in-N selective
authentication for SMS Requests. If the frequency is set for 12, then
the SGSN skips authentication for the first 11 events and authenticates
on the twelfth event.
frequency must
be an integer from 1 to 16.
sms-type
Enables authentication
for the following SMS types:
-
mo-sms:
mobile-originated SMS
-
mt-sms: mobile-terminated SMS
Usage:
By default, authentication
is not performed for short message service (SMS). Use this command
to enable/disable authentication and to fine-tune the authentication
procedure based on MS/UE access type and the frequency
for the selected SMS type. Repeat the commands as needed to configure
criteria for all service types.
Example:
The following command
configures MO-SMS authentication to occur every fifth request:
authenticate sms sms-type
mo-sms frequency 5
authenticate tau
Allows the operator
to enable/disable and fine-tune authentication for the tracking
area update (TAU) procedures.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
authenticate tau [ freqency frequency | inter-rat | periodicity interval ] no authenticate tau
inter-rat
no
Disables the TAU authentication
procedures specified in the call control profile configuration.
frequency frequency
Defines 1-in-N selective
authentication for this type of subscriber event - a tracking area update
for an inter-RAT Attach. If the frequency is set for 12, the MME
skips authentication for the first 11 events and authenticates on
the twelfth event.
frequency must
be an integer from 1 to 16.
inter-rat
Enables authentication
for TAU procedures for inter-RAT Attaches.
periodicity duration
Defines the length
of time (number of minutes) that authentication can be skipped.
duration:
Must be an integer from 1 to 10800.
Usage:
Authentication for
TAU procedures is disabled by default. This command enables/disables authentication
for a inter-RAT TAU procedures and allows the operator to limit
authentication based on the frequency of the events or elapsed intervals
between the events.
Example:
The following command
configures TAU authentication to occur when there is 15 minutes between
inter-RAT Attaches:
authenticate tau periodicity 15
The following command
disables authentication for all TAU Inter-RAT Attaches, use:
no authenticate tau
cc
Defines the charging
characteristics to be applied for CDR generation when the handling rules
are applied via the Operator Policy feature.
Product:
MME
SAEGW
S-GW
SGSN
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
cc { behavior-bit
no-records bit_value | local-value
behavior bit_value profile index_bit | prefer { hlr-hss-value | local-value } }no cc behavior-bit no-recordsremove cc { behavior-bit
no-records | local-value | prefer }
no
Disables the no records
generation behavior-bit configuration for this call control profile.
remove
Removes the specified
charging characteristic configuration from this profile.
behavior-bit no-records bit_value
Default: disabled
Specifies the charging
characteristic behavior bit. no-records instructs
the system not to generate any accounting records regardless of what
may be configured elsewhere.
bit_value is
an integer from 1 through 12.
local-value behavior bit_value profile index_bit
Defaults: bit_value = 0x0,
index_bit = 8
Sets the local value
of the behavior bits and profile index for the charging characteristics when
the HLR/HSS does not provide values for these parameters.
bit_value is
a hexadecimal value between 0x0 and 0xFFF.
index_bit is
an integer value from 1 through 15.
Setting the profile
index bis selects different charging trigger profiles to be used
with the call control profile. Some of the index values are predefined
according to 3GPP standard:
If the HLR/HSS
provides the charging characteristics with behavior bits and profile
index and the operator prefers to ignore the HLR/HSS values,
then also configure
the prefer local-value keyword.
prefer { hlr-hss-value | local-value }
Default: hlr-hss-value
Specifies a preference
for using charging characteristics settings received from HLR or HSS,
or those set by the SGSN or MME locally with the local-value behavior command.
-
hlr-hss-value sets
the call control profile to use charging characteristics settings
received from HLR or HSS. This is the default preference.
-
local-value sets
the call control profile to use charging characteristics settings
from the SGSN or MME only. If no charging characteristics are received
from the HLR/HSS then local values will be applied.
Usage:
Use this command to
set the behavior for charging characteristic comings from either
an HLR/HSS or locally from an MME/SGSN.
These charging characteristics
parameters can also be set within an APN profile with the commands
of the APN Profile configuration mode. For generation of M-CDRs,
the parameters configured in this mode, Call Control Profile configuration
mode, will prevail but for generation of S-CDRs the parameters configured
in the APN Profile configuration mode will prevail.
The 12 behavior bits
(of the local-value
behavior keyword) can be used to enable or disable CDR
generation.
Example:
The following command
specifies a rule not to generate charging records (CDRs) and sets the
charging characteristics behavior bit to
2:
cc behavior-bit no-records 2
check-zone-code
Enables or disables
the zone code checking mechanism.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no | remove ] check-zone-code
no
Included with the
command, this keyword disables the mechanism.
remove
Included with the
command, this keyword causes the removal of the current check-zone-code configuration
and returns to the SGSN to the default where zone-code checking
is enabled.
Usage:
Use this command to
enable/disable the zone-code checking function.
Example:
Disable checking of
the zone code:
no check-zone-code
ciphering-algorithm-gprs
Defines the order
of preference of the ciphering algorithms.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
ciphering-algorithm-gprs
priority priority
algorithmremove ciphering-algorithm-gprs
priority priority
remove
Delete the priority
definition.
priority priority
Sets the order in
which the algorithm will be selected for use.
priority is
an integer from 1 to 4.
algorithm
Identifies the ciphering
algorithm to be used.
algorithm is
one of the following: gea0, gea1,
gea2, gea3.
Usage:
Define the order in
which the ciphering algorithms are chosen for use. The command can be
repeated to provide multiple definitions -- multiple priorities.
Example:
Define gea1 as the
third priority algorithm:
ciphering-algorithm-gprs
priority 3 gea1
csfb
Configures circuit-switched
fallback options. CSFB is the mechanism to move a subscriber from
LTE to a legacy technology to obtain circuit switched voice or short message.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
csfb { policy { not-allowed | not-preferred | sms-only | suppress-call-reject } | sms-only }remove csfb { policy | sms-only }
remove csfb { policy | sms-only }
sms-only:
Removes the SMS-only restriction allowing the UE to request voice
and short message service (SMS) support for circuit-switched fallback
(CSFB).
policy: Removes
the configured policy.
policy { not-allowed | not-preferred | sms-only | suppress-call-reject }
not-allowed:
Specifies that the CSFB function is not allowed for both voice and
SMS.
not-preferred:
Specifies that the MME returns a “not-preferred” response
for CSFB services. The MME does not enforce this and a voice centric
is allowed to make CSFB calls on a not-preferred case if it chooses
to do so.
sms-only:
Specifies that the CSFB function only supports SMS.
suppress-call-reject:
Configures the MME to ignore a paging request for an SMS-only CS
call for an attached UE and suppress the paging reject. This allows
the MME to process SGs CS call SMS-only paging requests for Ultra Card
users where the same MSISDN is allocated to different IMSIs. By
default the MME will reject the paging request with a cause: SGSAP_SGS_CAUSE_MOBILE_TERMINATING_CSFB_REJECTED_BY_USER
sms-only
Specifies that the
circuit-switched fallback function only supports SMS.
IMPORTANT:
This is a legacy keyword
that remains to support earlier versions of the code. It operates identically
to the policy sms-only keyword.
Usage:
Use this command to
restrict the circuit-switched fallback function to SMS only or no support
for either voice or SMS.
Example:
The following command
enforces the SMS-only functionality for UEs requesting circuit-switched
fallback:
csfb policy sms-only
description
Allows you to enter
a relevant descriptive string.
Product:
MME
SAEGW
S-GW
SGSN
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
description descriptionno description
description
Enter an alphanumeric
string of 1 to 100 characters. The string may include spaces, punctuation,
and case-sensitive letters if the string is enclosed in double quotation
marks ( “ ).
no
Removes the description
from the call control profile.
Usage:
Define information
that identifies this particularly call control profile.
Example:
description “call-control-profile
handling incoming from CallTell”
diameter-result-code-mapping
Maps an EMM (EPS
Mobility Management) NAS (Network Access Server) cause code to a
Diameter result code.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
diameter-result-code-mapping
s6a diameter_result_code mme-emm-cause mme_emm_error_coderemove diameter-result-code-mapping
s6a diameter_result_code
remove diameter-result-code-mapping
s6a diameter_result_code
Removes the mapping
for the specified Diameter result code.
s6a diameter_result_code
Specifies the Diameter
result code to which the EMM NAS cause code is mapped.
diameter_result_code:
Specify one of the supported Diameter result codes:
-
diameter-authorization-rejected -
s6a result code 5003. Default mapped EMM code: “No suitable
cells in tracking area.”
-
diameter-error-other -
miscellaneous s6a error result code. Default mapped EMM code: “Network
failure.”
-
diameter-error-rat-not-allowed -
s6a result code 5421. Default mapped EMM code: “No suitable
cells in tracking area.”
-
diameter-error-roaming-not-allowed -
s6a result code 5004. Default mapped EMM code: “PLMN not
allowed.”
-
diameter-error-user-unknown -
s6a result code 5001/5030. Default mapped EMM code: “EPS
Service and non-EPS services not allowed.”
-
diameter-invalid-avp-value -
s6a result code 5004. Default mapped EMM code: “Network
failure.”
-
diameter-unable-to-comply -
s6a result code 5012. Default mapped EMM code: “Network
failure.”
-
diameter-unknown-eps-subscription -
s6a result code 5420. Default mapped EMM code: “No suitable
cells in tracking area.”
-
diameter-unsupported-feature -
s6a result code 5011. Default mapped EMM code: “Network
failure.”
mme-emm-cause mme_emm_error_code
Specifies the EMM NAS
cause code to be mapped to the Diameter result code.
mme_emm_error_code:
Specify one of the supported EMM NAS error codes:
-
eps-non-eps-not-allowed:
Specifies that the EMM NAS cause code #8 “EPS
services and non-EPS services not allowed” is to be mapped to
the specified Diameter result code.
-
network-failure:
Specifies that the EMM NAS cause code #17 “Network
failure” is to be mapped to the specified Diameter result
code.
-
no-suitable-cell-in-tracking-area:
Specifies that the EMM NAS cause code #15 “No
suitable cells in tracking area” is to be mapped to the specified
Diameter result code.
-
plmn-not-allowed:
Specifies that the EMM NAS cause code #11 “PLMN
not allowed” is to be mapped to the specified Diameter
result code.
-
roaming-not-allowed-in-this-tracking-area: Specifies
that the EMM NAS cause code #13 “Roaming not allowed
in this tracking area” is to be mapped to the specified
Diameter result code.
-
tracking-area-not-allowed:
Specifies that the EMM NAS cause code #12 “Tracking
area not allowed” is to be mapped to the specified Diameter
result code.
Usage:
Use this command to
map a selected EMM NAS cause code to a specific Diameter result code.
Example:
The following command
maps the EMM NAS cause code “Roaming not allowed in this tracking
area” to the Diameter result code “S6a Diameter
error RAT not allowed”:
diameter-result-code-mapping
s6a diameter-error-rat-not-allowed mme-emm-cause roaming-not-allowed-in-this-tracking-area
direct-tunnel
Allows direct tunneling
if direct tunneling is supported by the destination node.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
direct-tunnel attempt-when-permittedremove direct-tunnel
remove
Removes the configured
setting from the call control profile.
attempt-when-permitted
Enables direct tunneling
if the destination node allows it. Default: disabled.
Usage:
Use this command to
enable the Direct-Tunnel feature.
To ensure that direct
tunnel is fully configured for support by the SGSN, check the settings for
direct-tunnel in
-
the APN profile -- from
the Exec mode, use command:
show apn-profile <profile_name> all
-
the RNC (radio network
controller) configuration -- from the Exec mode, use command:
iups-service <service_name> all
IMPORTANT:
Direct tunneling must
be enabled at both of these two points to allow direct tunneling
for the MS/UE.
Example:
The following command
sets the configuration to instruct the SGSN to attempt to setup
a direct tunnel if permitted at the destination node:
direct-tunnel attempt-when-permitted
dns-ggsn
Defines the context
to be used to do DNS lookup for GGSNs.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
dns-ggsn context ctxt_nameno dns-ggsn context ctxt_name
no
Removes the dns-ggsn
configuration from this call control profile.
context ctxt_name
Specifies the context
to be used to do DNS lookup for GGSNs as an alphanumeric string
of 1 through 64 characters.
Usage:
Use this command to
define the context to be used to do DNS lookup to find the GGSN address.
dns-sgsn
Identifies the context
to be used to do DNS to find an SGSN address.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no ] dns-sgsn
context ctxt_name
no
Removes the dns-sgsn
configuration from this call control profile.
context ctxt_name
Identify the context
where the DNS client is configured to send the DNS query to get
the peer SGSN address.
context_name:
Enter a string of 1 to 79 alphanumeric characters to identify the
context.
This configuration
would override any similar configuration for dns-sgsn context in
the SGTP service configuration.
Usage:
Use this command to
configure the context ID for the SGSN address that will be used
to do the DNS lookup.
Example:
Configure context
sgsn1 for
DNS lookup:
dns-sgsn context sgsn1
dns-pgw
Defines the context
to be used to do DNS lookup for P-GWs.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] dns-pgw
context ctxt_name
remove
Deletes this definition
from the call control profile.
context ctxt_name
Specifies the context
to be used to do DNS lookup for P-GWs as an alphanumeric string
of 1 through 64 characters.
On the S4-SGSN, if the
interface selected for a UE is S4 and if there is no DNS-PGW context
configured under a call control profile, then by default the system
will look for the DNS client in the context where the eGTP service
is defined. If the interface selected for a UE is Gn-Gp and if there
is no dns-pgw context configured
in a call control profile, then by default the S4-SGSN will look
for the DNS client in the context where the SGTP service is configured
for selecting a co-located PGW/GGSN if:
-
the UE is EPC capable
and,
-
apn-resolve-dns-query
snaptr is configured in an APN profile using APN Profile Configuration
Mode.
If the dns-pgw context is
deleted with the remove option,
the S4-SGSN chooses the DNS client from the context where the eGTP
service is configured.
Usage:
Use this command to
configure the context ID for the DNS lookup.
dns-sgw
Defines the context
to be used to do DNS lookup for S-GWs.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] dns-sgw
context ctxt_name
remove
Deletes this definition
from the call control profile.
context ctxt_name
Specifies the context
to be used to do DNS lookup for S-GWs as an alphanumeric string
of 1 through 64 characters.
This command must be
used to configure DNS client settings when using dynamic S-GW selection
where the tai-mgmt-db has been associated with a call-control-profile.
On
the S4-SGSN, this specifies the name of the context where the DNS
client is configured that will be used for DNS resolution of S-GWs.
If
dns-sgw context is
not specified, the S4-SGSN uses the DNS client configured in the
context where the eGTP service is configured to query the S-GW DNS
address.
Usage:
Use this command to
configure the context ID for the DNS lookup.
encryption-algorithm-lte
Defines the priorities
for using the encryption algorithms.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
encryption-algorithm-lte
priority1 128-eea { 0 | 1 | 2 } priority2
128-eea { 0 | 1 | 2 } priority3
128-eea { 0 | 1 | 2 }remove encryption-algorithm-lte
remove
Deletes the priorities
definition from the call control profile configuration.
priority1 128-eea { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eea to
define the algorithm being given first priority.
priority2 128-eea { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eea to
define the algorithm being given second priority.
priority3 128-eea { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eea to
define the algorithm being given third priority.
Usage:
Set the order or priority
in which the MME will select a 128-EEA algorithm for use. All three
priorities must be set or the definition is invalid. The command
can be re-entered to change the priorities without removing the
configuration.
Example:
Configure 128-EEA2
as first priority encryption algorithm:
encryption-algorithm-lte
priority1 128-eea 2 priority2 128-eea 0 priority3 128-eea 1
encryption-algorithm-umts
Defines the priorities
for using the encryption algorithms.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
encryption-algorithm-umts { uea0 | uea1 | uea2 } [ then-uea# | then-uea# ] no encryption-algorithm-lte
no
Deletes the priorities
definition from the call control profile configuration.
{ uea0 | uea1 | uea2 }
Enter one of the three
options to define the first priority algorithm.
[ then-uea# | then-uea# ]
If a second algorithm
is to be included as an option, give it second priority. Enter 0,
1, or 2 at the end of then-uea to
define the algorithm being given second priority.
then-uea#
If a third algorithm
is to be included as an option, give it third priority. Enter 0,
1, or 2 at the end of then-uea to
define the algorithm being given third priority.
Usage:
Set the order or priority
in which the SGSN will select a UEA algorithm for use. It is not necessary
to define priorities for all three priority levels. The command
can be re-entered to change the priorities without removing the
configuration.
Example:
Configure algorithm
UEA2 as the first priority encryption algorithm with no others to
be considered:
encryption-algorithm-umts uea2
end
Exits the current
configuration mode and returns to the Exec mode.
Privilege:
Security Administrator,
Administrator
Usage:
Use this command to
return to the Exec mode.
equivalent-plmn
Configures the definition
for an equivalent public land mobile network identifier (PLMN ID)
and the preferred radio access technology (RAT). This is a of PLMNs
which should be considered by the mobile as equivalent to the visited
PLMN for cell reselection and network selection. When configured,
the equivalent PLMN list will be sent to the UE in NAS ATTACH ACCEPT / TAU
ACCEPT messages (up to 15 PLMNs in each message).
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
equivalent-plmn radio-access-technology { 2G | 3g | 4g | any } plmnid
mcc mcc_number mnc mnc_number priority priorityno equivalent-plmn
radio-access-technology { 2G | 3g | any } plmnid
mccmcc_number mnc mnc_number
no
Removes the equivalent-PLMN
configuration from this call control profile.
radio-access-technology { 2G | 3g | 4g | any }
Identify the RAT type
of the equivalent PLMN:
plmnid mcc mcc_number mnc mnc_number
-
mcc: Specifies
the mobile country code (MCC) portion of the PLMN ID. The number
can be any integer between 100 and 999.
-
mnc: Specifies
the mobile network code (MNC) portion of the PLMN ID. The number
can be any 2- or 3-digit integer between 00 and 999.
priority priority
Enter an integer between
1 and 15 with the highest priority assigned to the integer of the lowest
numeric value.
Usage:
Use the command to
identify an ‘equivalent PLMN’ and assign it a
priority to define the preferred equivalent PLMN to be used. This
command can be entered multiple times to set priorities of usage.
Example:
The following command
sets up a secondary equivalent PLMN definition that allows for any RAT
with a PLMN ID of MCC121.MNC767:
equivalent-plmn radio_access_technology
any plmnid mcc 121 mnc 767 priority 2
exit
Exits the current
mode and returns to the parent configuration mode.
Privilege:
Security Administrator,
Administrator
Usage:
Use this command to
return to the parent configuration mode.
gmm information-in-messages
Provides the configuration
to include the information in messages for the GPRS mobility management
(GMM) parameters.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
gmm information-in-messages
access-type { { gprs | umts } [ network-name { full-text name | short-text name } | [ send-after { attach | rau } ] }[ default | no ] gmm { information-in-messages
access-type { gprs | umts }
no
Disables the GMM configuration
from this call control profile.
default
Sets up a GMM configuration
with system default values.
access-type
Must select one of
the following options:
-
gprs - General
Packet Radio Service network
-
umts - Universal
Mobile Telecommunications System network
After selecting the
access-type, an additional parameter can be configured:
-
network-name:
identifies the network name in either short text or full text.
-
send-after:
configures the information in message to send after attachment or
Routing Area Update (RAU).
network-name { full-text name | short-text name }
This keyword provides
the option to add the network name to the message. The network name
will in full text or short text. Possible options are:
-
full-text
name: Indicate
the network name in full text
-
short-text
name: Indicate
the network name in short text
send-after{ attach | rau }
This keyword configures
the information in message to send after attachment or RAU message.
Possible options are:
-
attach:
Information sent after attachment
-
rau: Information
sent after routing area update
Usage:
Use this command to
configure identifying information about the network that will be included
in GMM messages.
Example:
Set default settings
for calls coming from 2.5G networks:
default gmm information-in-messages
access-type gprs
gmm retrieve-equipment-identity
Configures the International
Mobile Equipment Identity (IMEI) or software version (SV) retrieval
and validation procedure.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
gmm retrieve-equipment-identity { imei | imeisv [ unciphered ] [ then-imei ] } [ verify-equipment-identity [ deny-greylisted ] ][ no | default ] gmm
retrieve-equipment-identity
no
Disables the equipment
identity retrieval procedure configured for this call control profile.
default
Sets the default action
for equipment identity retrieval (EIR) procedure:
-
retrieve-equipment-identity:
Default action is disabled - no retrieval of IMEI/IMEI-SV
-
verify-equipment-identity:
Default action is disabled - no verification with Equipment Identity Register
(EIR)
equipment-identity-type
Default: disabled
Indicates the type
of equipment identification, with the possible values:
-
imei: International
Mobile Equipment Identity
-
imeisv:
International Mobile Equipment Identity - Software Version
imei
Indicates the equipment
identity retrieval type to International Mobile Equipment Identity
(IMEI). IMEI is a unique 15-digit number consisting of a TAC (Technical
Approval Code), a FAC (Final Assembly Code), an SNR (Serial Number),
and a check digit.
imeisv [ unciphered ] [ then-imei ]
Indicates the equipment
identity retrieval type to IMEI with software version (SV). IMEI
with SV is a unique 16-digit number consisting of a TAC (Technical
Approval Code), a FAC (Final Assembly Code), an SNR (Serial Number),
and a 2-digit software version number.
-
unciphered:
This optional keyword enables the unciphered retrieval of IMEI-SV.
If this option is enabled the retrieval procedure will get IMEISV
(if auth is still pending, get as part of Authentication and Ciphering
Response otherwise, via explicit Identification Request after Security
Mode Complete).
-
then-imei:
This optional keyword enables the retrieval of software version
number before the IMEI. If this option is enabled the equipment
identity retrieval procedure will get IMEISV on secured link (after
Security mode procedure via explicit GMM Identification Request),
and if MS is not having IMEISV (responded with NO Identity), SGSN
will try to get IMEI.
If no other keyword
is provided, imeisv will get IMEISV on a secured link (after a Security
mode procedure via explicit GMM Identification Request).
verify-equipment-identity [ deny-greylisted ]
Default: disabled
This keyword enables
the equipment identity validation and validates the equipment identity against
the EIR.
-
deny-greylisted:
This keyword fine-tunes the configuration and enables the restriction
to the user having mobile equipment with an IMEI in the EIR grey
list.
Usage:
Use this command to
enable and configure the procedures for mobile equipment identity retrieval
and validation from the EIR identified in the MAP Service Configuration
mode.
Example:
The following command
enables the SGSN to send “check IMEI” messages
to the EIR:
gmm retrieve-equipment-identity
imei verify-equipment-identity
gs-service
Associates the context
of a Gs service interface with this call control profile.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
gs-service gs_srvc_name context ctx_nameno gs-service svc_name
no
Removes/disassociates
the named Gs service from the call control profile.
gs-service gs_srvc_name
Specifies the name
of a specific Gs service for which to display information. gs_srvc_name is
the name of a configured Gs service expressed as an alphanumeric
string of 1 through 63 characters that is case sensitive.
context ctx_name
Specifies the specific
context name where Gs service is configured. If this keyword is omitted,
the named Gs service must exist in the same context as the GPRS/SGSN
service.
ctx_name is
name of the configured context of Gs service expressed as an alphanumeric
string from 1 through 63 characters that is case sensitive.
Usage:
Use this command to
associate a specific Gs service interface with this GPRS service instance.
IMPORTANT:
A Gs service can be
used with multiple SGSN and/or GPRS service.
Example:
The following command
associates a Gs service instance named
stargs1,
which is configured in context named
star_ctx,
with a call control profile:
gs-service stargs1
context star_ctx
gtp send
Configures which information
elements (IE) the SGSN sends in GTP messages. These are required
by the GGSN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
gtp send { imeisv [ derive-imeisv-from-imei ] | ms-timezone | rai [ use-local-plmn [ network-sharing { use-selected-plmn | use-ue-plmn | use-common-plmn } ] ]| rat | uli [ use-local-plmn [ network-sharing { use-selected-plmn | use-ue-plmn | use-common-plmn } ] ]}remove gtp send { imeisv | ms-timezone | rai | rat | uli }no gtp send
remove
Removes the specified
GTP send definition from the system configuration.
no
Disables the specified
GTP send configuration.
imeisv
Instructs the SGSN
to include the IMEISV (International Mobile Equipment Identity with Software
Version) of the mobile when sending GTP messages of the type Create
PDP Context Request.
By default, this function
is disabled.
derive-imeisv-from-imei
This is a filter for
the imeisv keyword.
It allows the operator to configure the SGSN to send IMEI to the
GGSN as IMEI-SV.
This filter instructs
the SGSN to add four 1s (1111) to the final semi-octet of the CPCQ (Create
PDP Context Request) message which enables the SGSN to deduce the
IMEI-SV value from the IMEI. If this filter is used, then IMEI is
also sent as IMEI-SV when the gmm retrieve-equipment-identity command
is configured.
ms-timezone
Instructs the SGSN
to include this IE in GTP messages of the type Create PDP Request
and Update PDP Context Request. This IE specifies the offset between
universal time and local time, where the MS currently resides, in
15-minute steps.
This IE is sent by
default.
rai
Configures the SGSN
to include the Routing Area Identity (RAI) of the SGSN in the following
situations:
-
-
-
2G -> 3G HO (only if
PLMN Id has changed)
-
3G -> 2G HO (only if
PLMN Id has changed)
-
multiple IUPS service
RAU (only if PLMN Id has changed)
-
multiple GPRS service
RAU (only if PLMN Id has changed)
-
3G new SGSN RAU (change
in behavior)
-
3G primary and secondary
PDP activation (change in behavior)
-
2G primary and secondary
PDP activation (change in behavior)
Optionally, this keyword
can be followed with the keyword selection for the PLMN - use-local-plmn.
rat
Specifies which radio
access technology (RAT) is being used by the MS (GERAN, UTRAN, or
GAN). Including this keyword instructs the SGSN to include this
IE when sending GTP messages of the type Create PDP Request and
Update PDP Context Request.
This IE is sent by
default.
uli
Specifies the CGI
(MCC, MNC, etc.) and SAI of the MS where it is registered. Including this
keyword instructs the SGSN to include the IE when sending GTP messages
of the type Create PDP Request and Update PDP Context Request.
This IE is not sent
by default.
Optionally, this keyword
can be followed with the keyword selection for the PLMN - use-local-plmn.
IMPORTANT:
Currently, the next
5 (five) keywords, are only used with parameters rai or uli.
use-local-plmn
This keyword selects
the local PLMN when network is not shared.
network-sharing
This keyword is used
to configure network-sharing.
use-selected-plmn
This keyword selects
the Selected PLMN when network is shared.
use-ue-plmn
This keyword selects
Selected PLMN for supporting UE and Common PLMN for non-supporting
UE when network is shared.
use-common-plmn
This keyword selects
the Common PLMN when network is shared.
Usage:
Use this command to
define a preferred set of information to include when GTP messages are
sent. Repeat this command multiple times to enable or disable multiple
options. This instruction will be implemented when the specific
operator policy and call control profile are applied.
The PLMN value in RAI/ULI
can be selected if 3G network-sharing is enabled.
Example:
The following command
series instructs the SGSN (1) not to send MS’ timezone
IE, and (2) to identify the MS’ radio access technology
info in the GTP messages:
no gtp send ms-timezone
gtp send rat
The next set of commands
provides examples indicating the usage of keywords to select PLMN
values in RAI/ULI.
On executing the following
command, ULI is sent and PLMN will be “use-selected-plmn” if network-sharing
is enabled. If network-sharing is not enabled, PLMN will be “use-local-plmn”.
gtp send uli
On executing the following
command, ULI is sent and PLMN will be “use-selected-plmn” if network-sharing
is enabled. If network-sharing is not enabled, PLMN will be “use-local-plmn”.
gtp send uli use-local-plmn
On executing the following
command, ULI is sent and PLMN will be “use-selected-plmn” if network-sharing
is enabled. If network-sharing is not enabled PLMN will be “use-local-plmn”.
gtp send uli use-local-plmn
network-sharing use-selected-plmn
On executing the following
command, ULI is sent and PLMN will be “use-common-plmn” if
network-sharing is enabled. If network-sharing is not enabled PLMN
will be “use-local-plmn”.
gtp send uli use-local-plmn
network-sharing use-common-plmn
gtpp
Enables secondary
GTPP accounting for an S-GW call control profile. By default, secondary
GTPP accounting is disabled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
gtpp secondary-group group_name [ accounting
context ctx_name ]no gtpp secondary-group
no
Disables secondary
GTPP accounting.
secondary-group group_name
Enables secondary
GTPP accounting and specifies a GTPP group name.
group_name must
be an alphanumeric string of 1 through 63 characters.
accounting context ctx_name
Specifies the specific
accounting context to be used for secondary GTPP accounting. If
this keyword is omitted, source context will be used for secondary
GTPP accounting.
ctx_name must
be an alphanumeric string of 1 through 79 characters.
Usage:
Use this command to
enable or disable secondary GTPP accounting for an S-GW call control
profile.
Example:
The following command
enables secondary GTPP accounting for an S-GW call control profile
and specifies a GTPP group named
gtpp-grp1:
gtpp secondary-group
gtpp-grp1
gtpu fast-path
Enables or disables
the network processing unit (NPU) Fast Path support for NPU processing
of GTP-U packets of user sessions at the NPU.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] gtpu
fast-path
remove
Removes the NPU fast
path functionality configuration from the call control profile.
Usage:
Use this command to
enable/disable the NPU processed fast-path feature for
processing of GTP-U data packets received from GGSN/RNC
or P-GW/eNodeB.
This feature enhances the GTP-U packet processing by adding the
ability to fully process and forward the packets through the NPU
itself.
IMPORTANT:
When enabled/disabled,
fast-path processing will be applicable only to new subscriber who establishes
a PDP context after issuing this command (enabling GTP-U fast path).
No existing subscriber session will be affected by this command.
Example:
The following command
enables the NPU fast path processing for all new subscribers’ session
established with this call control profile:
gtpu fast-path
gw-selection
Configures the parameters
controlling the gateway selection process.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] gw-selection { co-location [ weight [ prefer { sgw | pgw } ] ] | pgw weight | sgw
weight | topology [ weight [ prefer { sgw | pgw } ] ] }
remove gw-selection
Deletes the gw-selection
definition from the call control profile.
co-location [ weight [ prefer { sgw | pgw } ] ]
Selects “co-location” as
the determining factor for gateway selection. Collocation should
be configured for both P-GW and S-GW selection for collocation to
function. If a collocated PGW/SGW node cannot be found,
then topologically closest nodes are chosen next. Host names with
both “topon” and “topoff” labels
will be considered in collocation.
weight:
Enables weighted selection if there are multiple co-located pairs.
prefer { pgw | sgw}:
Configures which weight to be used for weighted selection.
pgw weight
Selects PDN-Gateway
as the determining factor for gateway selection.
sgw weight
Selects Serving Gateway
as the determining factor for gateway selection.
topology [ weight [ prefer { sgw | pgw } ] ]
Selects topology as
the determining factor for gateway selection. Topological selection
is done only during initial attach, and not used during S-GW relocation
or additional-pdn-connection.
weight:
Enables weighted selection if there are multiple pairs with the
same degree of topological closeness.
prefer { pgw | sgw}:
Configures which weight to be used for weighted selection.
Usage:
Use this command to
define the criteria for gateway selection.
Selection of a co-located
gateway (GW) node or a topologically closer GW node is based on
string comparison of canonical node names included in two or more
sets of records received in DNS S-NAPTR query result. For comparison,
the canonical node names are derived from the hostnames received
in the DNS records. The hostnames must adhere to the following format:
<topon|topoff>.<single-label-interface-name>.<canonical-node-name>;
Where “topon” or “topoff” is
a prefix of the hostname and indicates whether or not the canonical
node name can be used for topology matching.
The table below lists
the behaviors with various CLI options:
Table 1. CLI Behavior Options
| Option |
Keyword Selected |
Prefix
in Hostname |
Topological Match Nodes Selected |
Comments |
| 1 |
co-location |
topon |
Yes |
Co-located
nodes are selected if available as they are listed before topologically closer
nodes in the DNS records. |
| 2 |
co-location |
topoff |
Yes |
Co-located
nodes are selected if available as they are listed before topologically closer
nodes in the DNS records. |
| 3 |
topology |
topon |
Yes |
Co-located
nodes are selected if available as they are listed before topologically closer
nodes in the DNS records. |
| 4 |
topology |
topoff |
No |
Nodes
with prefix 'topoff' are ignored for topological matching purposes.
If no nodes are present with 'topon' as prefix then nodes are selected
independently based on Order/Priority mentioned in DNS
Records. |
| 5 |
co-location |
neither |
Yes |
Will
strip only the first label from hostname to fetch canonical node
name for topology matching. Co-located nodes are selected if available
as they are listed before topologically closer nodes in the DNS records. |
| 6 |
topology |
neither |
No |
No
co-located node pair listing; topologically closer node listing
used if available (Same behavior as defined for (4). |
Example:
The following command
instructs the MME to determine
gateway selection on the basis of topology:
gw-selection topology
idle-mode-signaling-reduction
Enables or disables
the Idle-Mode-Signaling-Reduction (ISR) feature on the S4-SGSN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] idle-mode-signaling-reduction access-type [ gprs | umts ]
remove
Disables the ISR feature
configuration from this call control profile.
idle-mode-signaling-reduction
Configures ISR for
this call control profile.
access-type
Specifies the network
access type for the ISR feature. Select one of the following options:
-
gprs - General
Packet Radio Service network. Specifies 2G network access support
for the ISR feature.
This
option is only supported for Release 15.0 and beyond.
-
umts - Universal
Mobile Telecommunications System network. Specifies 3G network access
support for the ISR feature.
Usage:
Use
this command to enable or disable the ISR feature on the S4-SGSN.
Note that ISR is supported on the S4-SGSN only.
This command is available
only if the Idle Mode
Signaling Reduction license is enabled on the SGSN.
When 3G ISR is enabled,
operators should set the ISR deactivation timer value sent by the S4-SGSN
to the UE in Attach Accept and Routing Area Update Accept messages.
Use the gmm T3323-timeout command
in SGSN Service Configuration
Mode to set the ISR deactivation timer value.
When 2G ISR is enabled,
operators should set the implicit detach timeout value to use for 2G
ISR. Use the gmm
implicit-detach-timeout command in GPRS Service Configuration
Mode.
Example:
idle-mode-signaling-reduction
access-type umts
integrity-algorithm-lte
Specifies the order
of preference for using an Integrity Algorithm.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
integrity-algorithm-lte
priority1 { 128-eia0 | 128-eia1 | 128-eia2 } priority2
128-eia { 0 | 1 | 2 } priority3
128-eia { 0 | 1 | 2 }remove integrity-algorithm-lte
remove
Deletes the priorities
definition from the call control profile configuration.
priority1 128-eia { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eia to
define the algorithm being given first priority.
priority2 128-eia { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eia to
define the algorithm being given second priority.
priority3 128-eia { 0 | 1 | 2 }
Enter 0, 1, or 2 at
the end of 128-eia to
define the algorithm being given third priority.
Usage:
Set the order or priority
in which the MME will select an integrity algorithm for use. All three
priorities must be set or the definition is invalid. The command
can be re-entered to change the priorities without removing the
configuration.
Example:
Configure 128-EIA0
as first priority integrity algorithm:
integrity-algorithm-lte
priority1 128-eia 0 priority2 128-eia 2 priority3 128-eia 1
integrity-algorithm-umts
Configures the order
of preference for the Integrity Algorithm used for 3G.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
integrity-algorithm-umts type then_ typedefault integrity-algorithm-umts
default
Specifies the default
preference based on system defaults.
type
Creates a configuration
defining an order of preference. Enter one or more of the following options
in the order of preference:
Usage:
Use this command to
determine which integrity algorithm is preferred 3G. This command is
configured in tandem with the algorithm type for encryption-algorithm-umts command.
Example:
default integrity-algorithm-umts
lcs-mo
This command enables/disables
mobile-originating Location Requests by access-type when Location
Services functionality is enabled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
lcs-mo { allow | restrict } access-type { gprs | umts }
allow
Enables mobile-originating
Location Requests. This is the default state when Location Services
are enabled.
Usage:
This command ties
Location Service functionality to a call-control profile by IMSI
so that Location Services can optionally be determined by an operator
policy for incoming calls.
Example:
Use the following
command to disable or disallow mobile-originating Location Requests within
a GPRS network:
lcs-mo restrict access-type GPRS
lcs-mt
This command enables/disables
mobile-terminating Location Requests by access-type when Location
Services functionality is enabled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
lcs-mt { allow | restrict } access-type { gprs | umts }
allow
Enables mobile-terminating
Location Requests. This is the default state when Location Services
are enabled.
Usage:
This command ties
Location Service functionality to a call-control profile by IMSI
so that Location Services can optionally be determined by an operator
policy for incoming calls.
Example:
Use the following
command to disable or disallow mobile-terminating Location Requests within
a UMTS network:
lcs-mt restrict access-type umts
lcs-ni
This command enables/disables
network-initiated Location Requests by access-type when Location
Services functionality is enabled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
lcs-ni { allow | restrict } access-type { gprs | umts }
allow
Enables network-initiated
Location Requests . This is the default state when Location Services
are enabled.
Usage:
This command ties
Location Service functionality to a call-control profile by IMSI
so that Location Services can optionally be determined by an operator
policy for incoming calls.
Example:
Use the following
command to enable or allow network-initiated Location Requests within
a UMTS network if this function has been restricted previously:
lcs-ni allow access-type umts
local-cause-code-mapping
apn-mismatch
Configures the
reject cause code to send to a UE when an APN mismatch occurs.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
apn-mismatch emm-cause-code { eps-service-not-allowed-in-this-plmn | esm-failure
esm-cause-code unknown-apn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
apn-mismatch
remove local-cause-code-mapping
apn-mismatch
Removes the configured
cause code mapping.
apn-mismatch emm-cause-code { eps-service-not-allowed-in-this-plmn | esm-failure
esm-cause-code unknown-apn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when an APN mismatch occurs.
-
eps-service-not-allowed-in-this-plmn
-
esm-failure esm-cause-code
unknown-apn - Default.
For the
esm-failure cause
code only, the
unknown-apn ESM
code is also reported to the UE.
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when an APN mismatch occurs,
such as when an APN is present in the HSS subscription but the HSS
subscription for this IMSI has other APNs present in the subscription.
If a condition is specified
in both the call-control-profile associated with a call, and also the
mme-service, the cause configured for the call-control-profile will
be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “PLMN not allowed” cause code to the
APN mismatch condition:
local-cause-code-mapping
apn-mismatch emm-cause-code plmn-not-allowed
local-cause-code-mapping
apn-not-subscribed
Gives the operator
the option to specify the local cause-code mapping when
the UE-requested APN is not subscribed.
Privilege:
Security Administrator, Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
apn-not-subscribed esm-cause-code
requested-service-option-not-subscribed
remove local-cause-code-mapping
apn-not-subscribed
remove
Deletes the local
cause code mapping from the configuration.
Usage:
The operator can specify
"Requested-Option-Not-Subscribed" cause
code value #33 will be sent in the Reject message when
the PDN Connectivity Request is rejected because no subscription
is found. If the command option is not configured, then
by default the MME uses the cause code value #27 (Unknown
or Missing APN) in standalone PDN Connectivity Reject message
when the UE-requested APN is not subscribed.
The new keyword apn-not-subscribed
is added to specify the local cause-code mapping when the
UE-requested APN is not subscribed for that subscriber. If
cause code mapping for apn-not-subscribed is explicitly
configured with requested-service-option-not-subscribed
in either the Call-Control-Profile or MME-Service
configuration mode, then the new code "Requested-Option-Not-Subscribed" (cause-code #33) will
be sent in the Reject message when the PDN Connectivity Request
is rejected because no subscription is found.
Example:
The following instructs
the MME to use cause code #33 ("Requested-Option-Not-Subscribed") in
place of the default #27 (Unknown or Missing APN):
local-cause-code-mapping
apn-not-subscribed esm-cause-code
requested-service-option-not-subscribed
local-cause-code-mapping
auth-failure
Configures the reject
cause code to send to a UE when an authentication failure occurs.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
auth-failure emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
auth-failure
remove local-cause-code-mapping
auth-failure
Removes the configured
cause code mapping.
auth-failure emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when an authentication failure
occurs.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when an authentication failure
occurs. By default, the MME sends the UE the #3 - Illegal
MS cause code when encountering an authentication failure.
This condition occurs
for TAU and ATTACH procedures in the following cases:
- The Authentication
response from the UE does not match the expected value in the MME.
- Security Mode Reject
is sent by the UE.
- The UE responds to
any identity request with a different type of identity (for example,
the MME could query for IMSI and the UE responds with IMEI).
The following are
not considered
for the authentication failure condition:
- HSS returning a result
code other than SUCCESS.
- HSS not available.
- EIR failures.
- UE not responding to
requests.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “network-failure” cause code to the authentication
failure condition:
local-cause-code-mapping
auth-failure emm-cause-code network-failure
local-cause-code-mapping
congestion
Configures the
reject cause code to send to a UE when a procedure fails due to
a congestion condition.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping congestion emm-cause-code { congestion [ esm-cause-code { congestion | insufficient-resources | service-option-temporarily-out-of-order } ] | eps-service-not-allowed-in-this-plmn | network
failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
congestion
remove local-cause-code-mapping
congestion
Removes the configured
cause code mapping.
congestion emm-cause { congestion [ esm-cause-code { congestion | insufficient-resources | service-option-temporarily-out-of-order } ] | eps-service-not-allowed-in-this-plmn | network
failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a UE requests access
when the system is exceeding any of its congestion control thresholds.
-
congestion -
Default
-
eps-service-not-allowed-in-this-plmn
-
network-failure
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
esm-cause-code { congestion | insufficient-resources | service-option-temporarily-out-of-order }
Specifies the EPS Session
Management (ESM) cause code to return when a UE requests access
when the system is exceeding any of its congestion control thresholds.
-
congestion -
Default
-
insufficient-resources
-
service-option-temporarily-out-of-order
Usage:
Use this command to
configure the cause code returned to a UE when a UE procedure fails due
to a congestion condition on the MME.
To set the cause codes
for situations where a call control profile cannot be attached to
a call (for example new-call restrictions, congestion during new
call attempt, etc.), use the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “network failure” cause code to the congestion
event:
local-cause-code-mapping
congestion emm-cause-code network-failure
local-cause-code-mapping
ctxt-xfer-fail-mme
Configures the reject
cause code to send to a UE when a UE context transfer failure from
a peer MME occurs.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
ctxt-xfer-fail-mme emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
ctxt-xfer-fail-mme
remove local-cause-code-mapping
ctxt-xfer-fail-mme
Removes the configured
cause code mapping.
ctxt-xfer-fail-mme emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a UE context transfer
failure from a peer MME occurs.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when a UE context transfer
failure from a peer MME occurs. By default, the MME sends the UE
the #9 - MS identity
cannot be derived by the network cause code for this condition.
After the peer node
has been identified, the MME sends a Context Request to the peer node.
If the peer node is an MME, and if the context transfer procedure
fails, this condition is detected.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “network-failure” cause code to the context
transfer failure from MME condition:
local-cause-code-mapping
ctxt-xfer-fail-mme emm-cause-code network-failure
local-cause-code-mapping
ctxt-xfer-fail-sgsn
Configures the reject
cause code to send to a UE when a UE context transfer failure from
a peer SGSN occurs.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
ctxt-xfer-fail-sgsn emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
ctxt-xfer-fail-sgsn
remove local-cause-code-mapping
ctxt-xfer-fail-sgsn
Removes the configured
cause code mapping.
ctxt-xfer-fail-sgsn
emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a UE context transfer
failure from a peer SGSN occurs.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when a UE context transfer
failure from a peer SGSN occurs. By default, the MME sends the UE
the #9 - MS identity
cannot be derived by the network cause code when encountering
this condition.
After the peer node
has been identified, the MME sends a Context Request to the peer node.
If the peer node is an SGSN, and if the context transfer procedure
fails, this condition is detected.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “network-failure” cause code to the context
transfer failure from SGSN condition:
local-cause-code-mapping
ctxt-xfer-fail-sgsn emm-cause-code network-failure
local-cause-code-mapping
gw-unreachable
Configures the reject
cause code to send to a UE when a gateway (S-GW or P-GW) does not
respond during an EMM procedure.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
gw-unreachable emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed } [ attach [ tau ] | tau [ attach ] ] | { no-bearers-active tau }
remove local-cause-code-mapping
gw-unreachable [ attach | tau ]
remove local-cause-code-mapping
gw-unreachable [ attach | tau ]
Removes the configured
cause code mapping.
gw-unreachable emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a gateway does not respond.
-
eps-service-not-allowed-in-this-plmn
-
network-failure
-
no-bearers-active
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
[ attach [ tau ] | tau [ attach ] ] | { no-bearers-active
tau }
Optionally, the MME can return
separate cause codes for Attach procedures and TAU procedures. This
capability is available for any of the above EMM cause codes except no-bearers-active,
which can only be defined for TAU procedures.
Usage:
Use this command to
configure the cause code returned to a UE when a gateway (S-GW or P-GW)
does not respond during an EMM procedure.
Defaults:
Prior to StarOS 15.0
MR5, the MME sends the UE the #19 - ESM
Failure cause code when encountering this condition.
In
StarOS 15.0 MR5 and higher releases, the MME sends the UE the #19 - ESM Failure cause
code for Attach procedures, and #40 - NO-EPS-BEARER-CONTEXT-ACTIVATED for
TAU procedures.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “network-failure” cause code to the gateway
unreachable condition:
local-cause-code-mapping
gw-unreachable emm-cause-code network-failure
local-cause-code-mapping
hss-unavailable
Configures the reject
cause code to send to a UE when the HSS does not respond.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
hss-unavailable emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
hss-unavailable
remove local-cause-code-mapping
hss-unavailable
Removes the configured
cause code mapping.
hss-unavailable emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when the HSS does not respond.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when the HSS is unavailable.
By default, the MME sends the UE the #17 - Network
failure cause code when encountering this condition.
This condition is detected
in the following cases:
- HSS resolution fails
in the MME.
- HSS does not respond
in time.
The cause code configured
for this condition will be signaled in TAU and ATTACH REJECT messages.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “tracking-area-not-allowed” cause code
to the HSS unavailable condition:
local-cause-code-mapping
hss-unavailable emm-cause-code tracking-area-not-allowed
local-cause-code-mapping
map-cause-code
Configures the
operator-preferred GMM reject cause code to send to a UE in response
to some failures.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
map-cause-code roaming-not-allowed
gmm-cause-code gmm-cause
remove local-cause-code-mapping
map-cause-code roaming-not-allowed
remove
Removes the specified,
previously configured cause code mapping .
roaming-not-allowed
Instructs the SGSN to
send a different GPRS mobility management (GMM) cause code to a UE
when the UE’s access request is rejected due to map cause ‘roaming
not allowed’. Specify one of the GMM cause codes listed
below.
gmm-cause-code
Specifies the GPRS mobility
management (GMM) cause code to return to a UE in access request
Reject messages. Replacement cause code options include:
-
gprs-serv-and-non-gprs-serv-not-allowed
-
gprs-serv-not-allowed
-
gprs-serv-not-in-this-plmn
-
location-area-not-allowed
-
network-failure
-
no-suitable-cell-in-this-la
-
plmn-not-allowed
-
roaming-not-allowed-in-this-la
Usage:
This command enables
the operator to configure a preferred GMM cause code to return to the
UE when a UE access request is rejected due to map-cause ‘roaming-not-allowed’.
Example:
The following command
maps network-failure as
the GMM cause code to be included in an Access Reject sent to the
UE when the UE is denied due to map-cause ‘roaming-not-allowed’:
local-cause-code-mapping
map-cause-code roaming-not-allowed gmm-cause-code network-failure
local-cause-code-mapping
no-active-bearers
Configures the reject
cause code to send to a UE when the context received from a peer SGSN
(during a TAU procedure) does not contain any active PDP contexts.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
no-active-bearers emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-bearers-active | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
no-active-bearers
remove local-cause-code-mapping
no-active-bearers
Removes the configured
cause code mapping.
no-active-bearers emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-bearers-active | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when no active PDP context exists.
-
eps-service-not-allowed-in-this-plmn
-
network-failure
-
no-bearers-active
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when the context received from
a peer SGSN (during a TAU procedure) does not contain any active
PDP contexts. By default, the MME sends the UE the #40 - No PDP
context activated cause code when encountering this condition.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “plmn-not-allowed” cause code to the
no active bearer condition:
local-cause-code-mapping
no-active-bearers emm-cause-code plmn-not-allowed
local-cause-code-mapping
peer-node-unknown
Configures the reject
cause code to send to a UE when peer node resolution is not successful.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
peer-node-unknown emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
peer-node-unknown
remove local-cause-code-mapping
peer-node-unknown
Removes the configured
cause code mapping.
peer-node-unknown emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when the peer node resolution
is not successful.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when peer node resolution is
not successful. By default, the MME sends the UE the #9 - MS identity
cannot be derived by the network cause code when encountering
this condition.
During processing of
a TAU REQUEST, the resolution of a peer MME that
had allocated the temporary identity that is signaled to the UE
takes several steps in the MME. This resolution can be done based
on DNS or based on local configuration. This condition occurs when
all mechanisms for peer node resolution are done with no success.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “plmn-not-allowed” cause code to the
peer node unknown condition:
local-cause-code-mapping
peer-node-unknown emm-cause-code plmn-not-allowed
local-cause-code-mapping
pgw-selection-failure
Configures the reject
cause code to send to a UE when a failure occurs during P-GW selection.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
pgw-selection-failure emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
pgw-selection-failure
remove local-cause-code-mapping
pgw-selection-failure
Removes the configured
cause code mapping.
pgw-selection-failure
emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a failure occurs during
P-GW selection.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when a failure occurs during
P-GW selection. By default, the MME sends the UE the #17 - Network failure cause
code when encountering this condition.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “plmn-not-allowed” cause code to the
P-GW selection failure condition:
local-cause-code-mapping
pgw-selection-failure emm-cause-code plmn-not-allowed
local-cause-code-mapping
restricted-zone-code
Configures the
reject cause code to send to a UE when a UE requests access to a restricted
zone.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
restricted-zone-code emm-cause-code { eps-service-not-allowed-in-this-plmn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
restricted-zone-code
remove local-cause-code-mapping
restricted-zone-code
Removes the configured
cause code mapping.
restricted-zone-code
emm-cause-code emm_cause_code
Specifies the EPS Mobility
Management (EMM) cause code to return when a UE requests access
to a restricted zone.
emm_cause_code must
be one of the following options:
-
eps-service-not-allowed-in-this-plmn
-
no-suitable-cell-in-tracking-area -
Default.
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when a UE requests access to
a restricted zone.
To set the cause codes
for situations where a call control profile cannot be attached to
a call (for example new-call restrictions, congestion during new
call attempt, etc.), use the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “PLMN not allowed” cause code to the
restricted zone code event:
local-cause-code-mapping
restricted-zone-code emm-cause-code plmn-not-allowed
local-cause-code-mapping
sgw-selection-failure
Configures the reject
cause code to send to a UE when a failure occurs during S-GW selection.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
sgw-selection-failure emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
remove local-cause-code-mapping
sgw-selection-failure
remove local-cause-code-mapping
sgw-selection-failure
Removes the configured
cause code mapping.
sgw-selection-failure
emm-cause-code { eps-service-not-allowed-in-this-plmn | network-failure | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed }
Specifies the EPS Mobility
Management (EMM) cause code to return when a failure occurs during
S-GW selection.
-
eps-service-not-allowed-in-this-plmn
-
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the cause code returned to a UE when a failure occurs during
S-GW selection. By default, the MME sends the UE the #17 - Network failure cause
code when encountering this condition.
If a cause code mapping
is specified in both the call-control-profile associated with a
call, and also the mme-service, the cause configured for the call-control-profile
will be signalled to the UE. See also the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “plmn-not-allowed” cause code to the
S-GW selection failure condition:
local-cause-code-mapping
sgw-selection-failure emm-cause-code plmn-not-allowed
local-cause-code-mapping
vlr-down
Configures the
cause code to send in a ATTACH ACCEPT or TAU ACCEPT to a UE that
attachment to the VLR has failed because a VLR down condition is
present.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
vlr-down emm-cause-code { congestion | cs-domain-unavailable | imsi-unknown-in-hlr | msc-temp-unreachable | network-failure }
remove local-cause-code-mapping
vlr-down
remove local-cause-code-mapping
vlr-down
Removes the configured
cause code mapping.
vlr-down emm-cause-code emm_cause_code
Specifies the EPS Mobility
Management (EMM) cause code to return when a VLR down condition
is present.
emm_cause_code must
be one of the following options:
-
congestion
-
cs-domain-unavailable
-
imsi-unknown-in-hlr
-
msc-temp-unreachable-
Default.
-
network-failure
Usage:
Use this command to
configure the cause code returned to a UE when a VLR down condition
is present.
To set the cause codes
for situations where a call control profile cannot be attached to
a call (for example new-call restrictions, congestion during new
call attempt, etc.), use the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration Mode Commands
chapter.
Example:
The following command
maps the “network failure” EMM cause code to the
VLR down condition:
local-cause-code-mapping
vlr-down emm-cause-code network-failure
local-cause-code-mapping
vlr-unreachable
Configures the
cause code to send in a ATTACH ACCEPT or TAU ACCEPT to a UE that
attachment to the VLR has failed because a VLR unreachable condition
is present.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
local-cause-code-mapping
vlr-unreachable emm-cause-code { congestion | cs-domain-unavailable | imsi-unknown-in-hlr | msc-temp-unreachable | network-failure }
remove local-cause-code-mapping
vlr-unreachable
remove local-cause-code-mapping
vlr-unreachable
Removes the configured
cause code mapping.
vlr-down emm-cause-code emm_cause_code
Specifies the EPS Mobility
Management (EMM) cause code to return when a VLR unreachable condition
is present.
emm_cause_code must
be one of the following options:
-
congestion
-
cs-domain-unavailable
-
imsi-unknown-in-hlr
-
msc-temp-unreachable -
Default.
-
network-failure
Usage:
Use this command to
configure the cause code returned to a UE when a VLR unreachable condition
is present.
To set the cause codes
for situations where a call control profile cannot be attached to
a call (for example new-call restrictions, congestion during new
call attempt, etc.), use the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration Mode Commands
chapter.
Example:
The following command
maps the “network failure” EMM cause code to the
VLR unreachable condition:
local-cause-code-mapping
vlr-unreachable emm-cause-code network-failure
location-area-list
Defines the location
area list to allow or restrict services in the specified location areas
identified by location area code (LAC).
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
location-area-list
instance instance area-code area_code [ area_code * ]no location-area-list
instance instance[ area-code area_code ]
no
If the area-code keyword
is included in the command, then only the specified area code is
removed from the identified list. If the area-code keyword
is not included with the command, the entire list of LACs is removed
from this call control profile.
instance instance
Specifies an identification
for the specific location area list.
instance must
be an integer between 1 and 5.
area-code area_code *
This keyword defines
the location area codes (LACs) to be used by this call control profile as
a determining factor in the handling of incoming calls. Multiple
LACs can be defined in a single location-area-list.
area_code:
Enter an integer between 1 and 65535.
* If
desired, enter multiple LACs separated by a single blank space.
Usage:
Use the command multiple
times to configure multiple LAC lists or to modify the a list.
Example:
The following command
creates a location area list for a single area code:
location-area-list
instance 1 area-code 514
This command creates
a second location area list for with multiple area codes - all separated by
a single blank space:
location-area-list
instance 2 area-code 514 62552 32 1513
The next command corrects
an area code mistake (327 not 32) made in the previous configuration:
location-area-list
instance 1 area-code 514 62552 327 1513
location-reporting
Enable 3G/2G
Location Change Reporting feature on the SGSN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] location-reporting
access-type { gprs | umts }
remove
If the remove keyword
is included in the command, then the location change reporting feature
is disabled.
access-type type
Defines the type of
subscriber access which is to reported for location changes.
Usage:
Use the command multiple
times to configure both types of access types.
This command enables
the 3G/2G Location Change Reporting feature which notifies
the GGSN whenever one of the following changes for a UE:
-
the serving cell global
identity (CGI), or
-
the service area identity
(SAI), or
-
the routing area identity
(RAI).
Example:
The following command
enables location change reporting to a GGSN for 3G subscribers:
location-reporting
access-type umts
This command disables
location change reporting that has been enabled for 2G subscribers:
remove location-reporting
access-type gprs
lte-zone-code
Configures the
enforcement of allowed or restricted zone code lists and associates
an EPS Mobility Management (EMM) cause code to rejected attach attempts.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
lte-zone-code [ allow | restrict } { emm-cause-code { eps-service-not-allowed-in-this-plmn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed ] zone-code-list zc_id +remove lte-zone-code
zone-code-list
remove
Removes the zone code
list from the call control profile.
[ allow | restrict ]
Specifies whether the
zone code list is allowed or restricted.
IMPORTANT:
You can only create
an allowed or restricted list, not both.
emm-cause-code [ eps-service-not-allowed-in-this-plmn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed ]
Optionally, specify
one of the following EMM cause codes to apply when a UE request
is rejected:
eps-service-not-allowed-in-this-plmn
no-suitable-cell-in-tracking-area
plmn-not-allowed
roaming-not-allowed-in-this-tracking-area
tracking-area-not-allowed
zone-code-list zc_id +
Specifies the zone code
in the allowed or restricted list of zone codes. zone_code must
be an integer value from 0 to 65535.
Usage:
Use this command to
create zone code lists that allow or restrict access to UEs managed
by this call control profile.
Example:
The following command
restricts access to zone codes 234 and 456 and returns an EMM cause
code of “tracking area not allowed”:
lte-zone-code restrict
emm-cause-code tracking-area-not-allowed zone-code-list 234 456
map
Configures the optional
extensions to Mobile Application Part (MAP) messages.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] map
message { mo-fwd-sm imsi | update-gprs-location { imeisv | private-extension
access-type } }
remove
IMEI-SV is not included
in the GLU request -- this is the default behavior.
message mo-fwd-sm imsi
Configures the SGSN
to include the IMSI of the originating subscriber in the mobile-originated
SM transfer. This parameter shall be included when the sending entity
(MSC or SGSN) supports mobile number portability (MNP). This IMSI
IE is required in the in MAP-MO-FORWARD-SHORT-MESSAGE in countries
where MNP is deployed.This keyword-set is required. The default
is disabled.
update-gprs-location
Includes a GLU message.
imeisv
Specifies the International
Mobile equipment Identity-Software Version (IMEI-SV) information
to include in the GPRS Location Update (GLU) request message. SGSN
will include IMEI-SV in the message, if available. Default: disabled
private-extension access-type
Includes a specific
access-type private extension in the message.
Usage:
This command configures
optional extensions to MAP messages. The HLR should ignore these
extensions if not supported by the HLR.
Example:
Use the following
command to have the SGSN add GLU extension information to the MAP messages
sent to the HLR.
map message update-gprs-location
private-extension access-type
map-service
Identifies a Mobile
Application Part (MAP) service and the context which contains it
and associates both with the call control profile.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
map-service context ctxt_name service map_srvc_nameno map-service context
no
Disables use of MAP
service with this call control profile.
context ctxt_name
Specifies the name
of the context for the MAP service as an alphanumeric string of
1 through 64 characters.
service map_srvc_name
Specifies the MAP
service name as an alphanumeric string of 1 through 64 characters.
Usage:
Use this command to
enable or disable MAP service with this call control profile.
max-bearers-per-subscriber
Defines the maximum
number of bearers allowed per subscriber.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
max-bearers-per-subscriber numberremove max-bearers-per-subscriber
remove
Deletes the definition
from the call control profile.
number
Identifies the maximum
number of bearers allowed per subscriber as an integer from 1 to 11.
Usage:
Use this command to
set the maximum number of bearers allowed per subscriber.
Example:
Set the maximum to
3:
max-bearers-per-subscriber 3
max-pdns-per-subscriber
Defines the maximum
number of PDNs allowed per subscriber.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
max-pdns-per-subscriber numberremove max-pdns-per-subscriber
remove
Deletes the definition
from the call control profile.
number
Identifies the maximum
number of PDNs allowed per subscriber as an integer from 1 to 11.
Usage:
Use this command to
set the maximum number of PDNs allowed per subscriber.
Example:
Set the maximum to
4:
max-pdns-per-subscriber 4
min-unused-auth-vectors
Configures a specific
minimum number of unused vectors to be maintained by the SGSN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
min-unused-auth-vectors min#_vectorsremove min-unused-auth-vectors
remove
Removes the definition
from the configuration file and restores the default behavior, which does
not use the threshold.
min#_vectors
Enables and defines
a threshold for the minimum number of unused vectors that the SGSN retains
to trigger the initation of a service area identity request (SAI)
.
min#_vectors:
Enter a digit betwen 1 and 4.
Usage:
Vectors are used by
the SGSN for authentication. Use this command to enable a minimum threshold
for unused vector for this call control profile. When the unused
vector count falls below this configured threshold, then an SAI
is initiated to fill the buffer back to 5 or to the most appropriate
number based on the MAP service configuration.
Example:
Enter a command similar
to the following to set a threshold of
3:
min-unused-auth-vectors 3
Use the following command
to disable this function and restore the default behavior, which does
not use a threshold to trigger an SAI:
remove min-unused-auth-vectors
network-feature-support-ie
Configures support
for the IMS Voice over Packet-Switched indication.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
network-feature-support-ie
ims-voice-over-psremove network-feature-support-ie
remove
Disables support for
Voice over PS.
ims-voice-over-ps
Enables support for
Voice over PS in all Tracking Areas.
Usage:
Use this command to
include the “IMS Voice over PS” indication, thereby
indicating support for IMS Voice over PS sessions for all Tracking
Areas.
Example:
The following command
enables support for IMS Voice over PS on the MME:
network-feature-support-ie
ims-voice-over-ps
network-initiated-pdp-activation
Configures the call
control profile to perform two functions: (1) to enable or disable
network-requested PDP context activation (NRPCA) for 3G attachments
and (2) to define a failure cause code for inclusion in NRPCA-related
reject messages.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] network-initiated-pdp-activation { allow
primary | restrict primary | secondary } access type { gprs | umts } { all | location-area-list instance <instance> }network-initiated-pdp-activation
primary access type { gprs | umts } { all | location-area-list
instance <instance> } failure-codecodenetwork-initiated-pdp-activation
secondary access type { gprs | umts } { all | location-area-list
instance <instance> } failure-codecode
remove
Including this keyword
with the command, removes all configured values for the specified configuration.
allow
Allows network-initiated
PDP context activation. This keyword must be followed by other parameters
to indicate the limitations for allowing the NRPCA.
Allow is the default
for NRPCA.
restrict
Restricts network-initiated
PDP context activation. This keyword must be followed by other command
parameters to indicate the limitations for restricting the NRPCA.
primary
Specifies that only
network-initiated primary PDP context activations are to be allowed.
secondary
Specifies that only
network-initiated secondary PDP context activations (NRSPCAs) are
to be allowed.
IMPORTANT:
The secondary keyword
is visible and can be selected. However, NRSPCA functionality is
only supported for Release 15.0 onwards.
all
Configures the SGSN
to allow or to restrict NRPCA for calls within all location areas.
location-area-list
instance instance
Selects a pre-defined
list of location area codes (LACs) and allows/restricts
the NRPCA procedure for calls within the listed area codes.
instance:
Enter a list ID; an integer between 1 and 5.
IMPORTANT:
Before using this
keyword, ensure that the appropriate LAC information has been defined with
the location-area-list command,
also in this configuration mode.
failure-codes code
Enter an integer from
192 to 226 to identify the GTPP failure cause code (from 3GPP TS29.060,
list below) to be included in the reject messages when NRPCA is
restricted. If a failure cause code is not defined, the default
value is 200 (service not supported).
-
-
193 - Invalid message
format
-
-
195 - MS is GPRS Detached
-
196 - MS is not GPRS
Responding
-
-
198 - Version not supported
-
199 - No resources
available
-
200 - Service not supported
-
201 - Mandatory IE
incorrect
-
202 - Mandatory IE
missing
-
203 - Optional IE incorrect
-
-
205 - Roaming restriction
-
206 - P-TMSI Signature
mismatch
-
207 - GPRS connection
suspended
-
208 - Authentication
failure
-
209 - User authentication
failed
-
-
211 - All dynamic PDP
addresses are occupied
-
212 - No memory is
available
-
-
214 - Unknown mandatory
extension header
-
215 - Semantic error
in the TFT operation
-
216 - Syntactic error
in the TFT operation
-
217 - Semantic errors
in packet filter(s)
-
218 - Syntactic errors
in packet filter(s)
-
219 - Missing or unknown
APN
-
220 - Unknown PDP address
or PDP type
-
221 - PDP context without
TFT already activated
-
222 - APN access denied – no
subscription
-
223 - APN Restriction
type incompatibility with currently active PDP Contexts
-
224 - MS MBMS Capabilities
Insufficient
-
225 - Invalid Correlation-ID
-
226 - MBMS Bearer Context
Superseded
Usage:
Use this command to
allow or restrict network-requested PDP context activation (NRPCA)
based on access-type and location areas. NRPCA is used when there
is downlink data at the GGSN for a subscriber, but there is no valid
context for the already-established PDP address so the GGSN initiates
an NRPCA procedure towards the SGSN.
This command can also
be used to define the failure cause code that will be included in activation
reject messages.
These commands can
be repeated to define a unique set of NRPCA parameters for each access-type
and each location area list.
The T3385-timeout and
the max-actv-retransmission timers
configure the retransmission timer and the number of retries for
PDP context activation requests. Both of these timers are set in
the SGSN service configuration mode.
The configuration for
NRPCA can be viewed via the show call-control-profile
full name profile_name. Statistics
associated with NRPCA can be seen via the show gmm-sm statistics output
and via the show
sgtpc statistics verbose output.
Example:
The following command
changes the failure code for Reject messages from 200 (service not supported)
to 205 (roaming restriction) for primary NRPCA for all GRPS access
and all LACs:
network-initiated-pdp-activation
primary access-type gprs all failure-code 205
The following command
enables network-initiated primary PDP context activation for UMTS
calls from the LACs in location-area-list 1:
network-initiated-pdp-activation
allow primary access-type umts location-area-list instance 1
The following command
restricts network-initiated primary PDP context activation for UMTS
calls from the LACs in location-area-list 2:
network-initiated-pdp-activation
restrict primary access-type umts location-area-list instance 2
override-arp-with-ggsn-arp
Enables or disables
the ability of the SGSN to override an Allocation/Retention Priority
(ARP) value with one received from a GGSN. If there is no authorized
Evolved ARP received from the GGSN, by default the SGSN continues
to use the legacy ARP included in the Quality of Service (QoS) Profile
IE.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] override-arp-with-ggsn-arp
remove
Adding the remove keyword
to the command disables the override feature.
Usage:
Enabling this function
on the SGSN will allow the ARP sent by the GGSN, in CPCR / UPCR / UPCQ,
to be applicable as an overriding value.
Example:
Use this command to
configure the SGSN to negotiate the ARP to be used as an overriding value:
override-arp-with-ggsn-arp
pdp-activate access-type
Configures the PDP
context activation option based the type of access technology.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
pdp-activate access-type { grps | umts } { all | location-area-list
instance instance } failure-code failure_codedefault pdp-activate
access-type { grps | umts } { all | location-area-list
instance instance } failure-code code
default
Resets the configuration
to system default values for PDP context activation request.
{ grps | umts }
Specifies the access
technology type for PDP context activation.
-
gprs: Enables
access type as GPRS.
-
umts: Enables
access type as UMTS.
all
Default: allow
Configures the system
to allow the creation of all PDP context activation requests received from
MS.
location-area-list
instance instance
Specifies the location
area instance for which to create a PDP context as an integer from
1 through 5. The value must be an already defined instance of a
location area code (LAC) list created via the location-area-list command.
failure-code code
Specifies the failure
code for PDP context activation as an integer from 8 through 112. Default:
8
Usage:
Use this command to
configure this call control profile to allow GPRS/UMTS
access through PDP context activation request from MS.
Example:
The following command
configures the system to create the PDP context for requests from MS
for GPRS access with location area list instance
2 and failure-code
5:
pdp-activate access-type
gprs location-area-list 2 failure-code 5
pdp-activate allow
Configures the system
to allow the PDP context activation based on the type of access
technology.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no ] pdp-activate
allow access-type { grps | umts } location-area-list
instance instance
no
Removes the configured
permission to create PDP context on request of PDP context activation
from MS for an access type.
access-type { grps | umts }
Specifies the access
technology type for PDP context activation.
-
gprs: Enables
access type as GPRS.
-
umts: Enables
access type as UMTS.
location-area-list
instance instance
Specifies the location
area instance to create PDP context.
instance must
be an integer from 1 through 5. The value must be an already defined
instance of a location area code (LAC) list created via the location-area-list command.
Usage:
Use this command to
configure this call control profile to allow GPRS/UMTS
access through PDP context activation request from MS.
Example:
The following command
configures the system to allow the PDP context activation for GPRS
access type with location area list instance
2:
pdp-activate allow
access-type gprs location-area-list instance 2
pdp-activate restrict
Configures the system
to restrict the PDP context activation based on the type of access
technology.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no | remove ] { { access-type { gprs | umts } { all | location-area-list
instance instance } } | { pdp-type { all | dual-ipv4v6 | ipv4 | ipv6 | ppp } { access-type { gprs | umts } { all | location-area-list
instance instance } } } | { secondary-activation
access-type { gprs | umts } { all | location-area-list
instance instance } } }
no | remove
Either of these prefixes
removes the previously configured restriction on PDP context activation
and returns the ‘allow’ default.
access-type { grps | umts }
Specifies the access
technology type for which to restrict PDP context activation.
-
gprs: Enables
access type as GPRS.
-
umts: Enables
access type as UMTS.
-
all: Configures
the system to restrict all PDP context activation requests from
the MS.
-
location-area-list
instance instance:
Specifies the location area instance to restrict PDP context activation,
where
list_id must
be an integer from 1 through 5. The value must be an already defined
instance of a location area code (LAC) list created with the
location-area-list command.
pdp-type
Sets the configuration
to restrict PDP activation based on the requested PDP type.
To restrict more than
one type of PDP, the command must be reissued for each PDP type.
-
all: restricts
activation of all types PDP.
-
dual-ipv4v6:
restricts activation when dual-IPv4v6 PDP contexts are requested.
-
ipv4: restricts
activation when IPv4 PDP contexts are requested.
-
ipv6: restricts
activation when IPv6 PDP contexts are requested.
-
ppp: restricts
activation when PPP PDP contexts are requested.
secondary-activation
Restricts the SGSN,
based on the access-type, so that secondary PDP contexts are not created
when receiving the PDP Context Activation Request from the MS.
Usage:
Use this command to
configure this call control profile to restrict PDP context activation requests
from MS.
Example:
The following command
configures the system to restrict the PDP context activation for request
from 2G MS with location area list instance
2:
pdp-activate restrict
access-type gprs location-area-list instance 2
The following command
configures the SGSN to restrict PDP context activation for requests from
3G MS if their PDP-type is IPv4. The second command restricts based
on PDP-type IPv6.
pdp-activate restrict
pdp-type ipv4 access-type umts all
pdp-activate restrict
pdp-type ipv6 access-type umts location-area-list instance 1
pdn-type-override
Configures the MME
or the SGSN to override the requested packet data network (PDN)
type based on the inbound roamer PLMN, and re-assigns the UE to
an IPv4-only or IPv6-only PDN. This override can be applied based
on the type of access technology.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
pdn-type-override
ipv4v6 { ipv4 | ipv6 } [ access-type { eps | grps | umts } ] remove pdn-type-override [ access-type { eps | grps | umts } ]
remove
Removes the configured
PDN type override.
ipv4v6 { ipv4 | ipv6 }
Defines the PDN type
(IPv4 or IPv6) to which UEs should be restricted.
access-type { eps | grps | umts }
Specifies the access
technology type to which the override is applied.
-
eps- enables
PDN override for EPS access type.
-
gprs - enables
PDN override for GPRS access type.
-
umts - enables
PDN override for UMTS access type.
If this keyword is not
included, then all three access types can have the PDN type overridden.
Usage:
Use this command to
configure the call control profile to override the requested packet data
network (PDN) type and re-assign the UE to a different PDN type.
Optionally, it is possible to filter the override based on access
technology.
IMPORTANT:
This call control profile
becomes valid only when it is associated with an operator policy using
the associate command
in the Operator Policy configuration mode.
Example:
The following command
configures the system to override the requested PDN type and assign
a UE to an IPv4-only PDN if the UE’s access technology
is GPRS:
pdn-type-override
ipv4v6 ipv4 access-type gprs
peer-mme
Configures a
peer MME address. S4-SGSN operators can use this command if they
wish to bypass DNS resolution to obtain the MME address.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
peer-mme { mme-groupid <lac val> mme-code <rac value> | tac tac } prefer { fallback-for-dns | local } address { <ipv4_address> | <ipv6_address> } interface { gn [ s3 ] | s3 [ gn ] } remove peer-mme { mme-groupid <lac val> mme-code <rac value> | tac tac } address [ <ipv4_address> | <ipv6_address> [ interface { gn [ s3 ] | s3 [ gn ] } ]
remove
Removes a specified
peer MME from the call control profile. The interface keyword
is optional. If it is not used, the entire interface will be deleted.
mme-groupid <lac val>
Specifies the location
area code value of the peer MME. The MME group ID of the peer MME
maps to the LAC value when GUTI is converted to P-TMSI.
<lac val> must
be an integer from 1 to 65535.
mme-code <rac value>
Specifies the routing
area code value of the peer MME. The MME code of the peer MME maps
to the RAC value when GUTI is converted to P-TMSI.
<rac value> must
be an integer from 0 to 255.
tac tac
Optional. Specifies
the Tracking Area Code (TAC) of the target eNodeB that is used for UTRAN
to E-UTRAN (SGSN to MME) SRNS relocation across the S3 interface.
Valid entries are 1 to 65535. This setting applies only if SRNS
relocation first has been configured via the srns-inter and/or srns-intra commands
in Call Control Profile
Configuration Mode.
prefer { fallback-for-dns | local }
Indicates whether to
use a DNS query to obtain the address or to use a locally configured peer
MME address:
-
fallback-for-dns -
Instructs the SGSN to perform a DNS query to get the IP address
of the peer MME. If the DNS query fails, then the IP address configured
with this command is used.
-
local - Use
the locally configured address for the MME address.
IMPORTANT:
If the prefer command
is used to change an existing peer-mme configuration (with the same
LAC and RAC) from fallback-for-dns to localor from local to fallback-for-dns,
the new setting overwrites the previously configured setting for
all interfaces.
address { ipv4_address | ipv6_address }
Specifies the IP address
of the peer MME. Currently, the IPv6 address option is not supported
on the S4-SGSN.
ipv4 must
be in standard dotted-decimal notation.
interface { gn [ s3 ] | s3 [ gn ] }
Specifies the interface
to use for communication between the SGSN and the peer MME:
-
gn: Use the
Gn interface between the S4-SGSN and the MME in the LTE network.
-
s3: Use the
S3 interface between the S4-SGSN and the MME in the LTE network.
This is the default setting.
Usage:
Use this command to
instruct the S4-SGSN how to determine a peer MME address, via DNS
or local configuration. For a local address, use this command to
configure the peer MME address.
This command also sets
the interface type to be used between the peer MME and the SGSN.
Example:
The following command
configures LAC/RAC
111/22 for
the peer MME and instructs the SGSN to use the MME’s locally
configured IPv4 address of
1.1.1.1 and
an S3 interface between the MME and the SGSN.
peer-mme mme-groupid
111 mme-code 22 prefer local address 1.1.1.1 interface s3
peer-nri-length
Enables the SGSN to
use NRI-FQDN-based DNS resolution for non-local
RAIs when selection of the call control profile is based on the
old-RAI and the PLMN Id of the RNC where the subscriber
originally attached.
The SGSN
also supports RAI based query when NRI based query fails.
Privilege:
Security Administrator, Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
peer-nri-length length [rai-fqdn-fallback]remove peer-nri-length [rai-fqdn-fallback]
remove
Deletes the NRI length
configuration for the non-local RAIs and the SGSN sends
RAI-FQDN-based DNS resolution.
length
This defines the NRI
length for the peer SGSN and enables use of NRI-FQDN-based
DNS resolution for non-local RAIs. This variable
allows for an integer from 1 to 10.
Usage:
IMPORTANT:
- This feature is supported
only for 3G subscribers until Release 15.0.
The command enables
the SGSN to perform DNS query with an NRI when RAU comes from an
SGSN outside the pool. The SGSN uses NRI-FQDN-based
DNS resolution for the non-local RAIs for 3G subscribers
in place of RAI-FQDN-based DNS resolution.
This functionality is
applicable in situations for either inter- or intra-PLMN
when the SGSN has not chosen a local NRI value (configured
with SGSN Service commands) other than local-pool-rai or nb-rai. This
means the RAI (outside pool but intra-PLMN) NRI
length configured here will be applicable even for intra-PLMN
with differently configured NRI lengths (different from
the local pool).
This functionality
is not applicable to call control profiles with an associated MSIN
range as ccprofile selection is not IMSI-based. When
this feature is enabled, the selection of the ccprofile
is based on the old-RAI and the PLMN Id (if configured) of
the RNC where the subscriber
originally attached.
Example:
The
following command is used to configure a peer-nri-length
of
3, with support for RAI based query
when NRI based query fails:
peer-nri-length
3 rai-fqdn-fallback
plmn-protocol
Configures the protocol
supported by the PLMN (Public Land Mobile Network).
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
plmn-protocol plmnid
mcc mcc_num mnc mnc_num { s5-protocol | s8-protocol } { gtp | pmip }remove plmn-protocol
plmnid mcc mcc_num mnc mnc_num
remove
Deletes the definition
from the call control profile configuration.
plmn-id mcc mcc_num mnc mnc_num
Identifies the PLMN
by MCC (mobile country code) and MNC (mobile network code).
mcc_num:
Enter a 3-digit integer from 100-999.
mnc_num:
Enter a 2- or 3-digit integer from 00 to 999.
s5-protocol | s8-protocol
Select which protocol – S5
or S8 – that controls the identified PLMN.
gtp | pmip
Select the protocol variant
- GTP or PMIP - that controls functionality for the identified PLMN.
Usage:
Use this command to
identify a particular PLMN and, at a higher level, its operational characteristics.
Example:
The following command
instructs the MME to use PLMN MCC423.MNC40.GPRS with PMIP under
S8 Protocol:
plmn-protocol plmnid
mcc 423 mnc 40 s8-protocol pmip
prefer subscription-interface
Selects the specified
subscription interface (Gr or S6d) if both interface types are associated
with a call-control-profile. Use of this command requires an S6d
license.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
prefer subscription-interface { hlr | hss
}remove prefer subscription-interface
remove
Removes the preferred
subscription-interface for the call control profile.
hlr
Selects the HLR Gr
interface.
hss
Selects the HSS S6d
interface.
Usage:
Use of this command
requires an S6d license.
The SGSN provides
a mechanism to associate a MAP service with call control profile.
It is possible that both MAP service and HSS peer service are associated
with the call control profile. If the interface preference selected
is “hlr”, the MAP protocol is used to exchange
messages with the HLR. If the interface preference selected is “hss”,
the Diameter-protocol is used to exchange messages with the HSS.
Example:
The following command
specifies that “hss” for S6d is selected as the
subscription-interface:
prefer subscription-interface hss
ptmsi-reallocate
Defines P-TMSI reallocation
for Attach Requests, RAU Request, and Service Requests.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
ptmsi-reallocate { attach | frequency frequency | interval interval | routing-area-update [ update-type ] | service-request [ service-type ] } [ access-type { gprs | umts } ]ptmsi-reallocate routing-area-update [ access-type { gprs | umts } | frequency frequency | update-type { combined-update | imsi-combined-update | periodic | ra-update } [ access-type { gprs | umts } | frequency frequency ] ]ptmsi-reallocate service-request [ frequency frequency | service-type { data | page-response | signaling } [ frequency frequency ] ][ no | remove ] ptmsi-reallocate { attach | frequency | interval | routing-area-update [ update-type { combined-update | imsi-combined-update | periodic | ra-update } [ access-type { gprs | umts } ] ] | service-request [ service-type { data | page-response | signaling } ] } [ access-type { gprs | umts } ]
no
Disables the authentication
procedures configured for the specified P-TMSI reallocation configuration
in the call control profile.
remove
Deletes the defined
authentication procedures for the specified P-TMSI reallocation configuration
from the call control profile configuration file.
attach
Enables/disables
P-TMSI reallocation for Attach with local P-TMSI.
IMPORTANT:
IMSI or inter-SGSN
Attach is not configurable and will always be reallocated.
access-type type
One of the following
must be selected to reallocate on the basis of the type of network access:
This keyword can be
used in combination with other keywords to refine the reallocation configuration.
frequency frequency
Defines frequency of
the reallocation based on the number of messages skipped. If the frequency
is set for 1, then the SGSN skips 1 message and then reallocates
on receipt of the 2nd (alternate) request message, essentially reallocating
the P-TMSI every time. If the frequency is set for 12, then the
SGSN skips reallocation for 12 messages and reallocates on receipt
of the 13th request message. This keyword can be used in combination
with other keywords to refine the reallocation configuration.
frequency must
be an integer from 1 to 50.
By default, frequency
is not defined and, therefore, reallocation is done for every request message
and none are skipped.
interval minutes
Enter an integer between
1 and 1440 to define the time interval (in minutes) for skipping
the service/RAU/attach request message procedure.
routing-area-update [ update-type ]
Enables/disables
P-TMSI reallocation for RAU (routing area update) with local P-TMSI.
To refine the reallocation configuration, include one of the optional
types of updates to limit reallocation:
IMPORTANT:
Inter-SGSN RAU will
always be reallocated.
service-request [ service-type ]
Enables/disables
P-TMSI reallocation for Service Requests. To refine the Service-Request reallocation
configuration, include on of the optional service-types to limit
the reallocation:
Usage:
By default, reallocation
is not enabled. Use this command to enable P-TMSI reallocation for
Attach Requests, RAU Request, and Service Requests. Fine-tune the
reallocation configuration according to frequency, interval, or
access-type.
Example:
The following command
configures the SGSN to perform P-TMSI reallocation upon receiving
2G Attach Requests
ptmsi-reallocate attach
access-type gprs
The following command
configures the SGSN to disable all previously defined P-TMSI reallocations
based on the combined criteria of interval and 3G requests:
no ptmsi-reallocate
interval access-type umts
ptmsi-signature-reallocate
Enables P-TMSI signature
reallocation during Attach/RAU procedures.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
ptmsi-signature-reallocate { attach | frequency frequency | interval interval | ptmsi-reallocation-command | routing-area-update [ update-type ] } [ access-type { gprs | umts } | frequency frequency ]ptmsi-signature-reallocate
routing-area-update [ access-type { gprs | umts } | frequency frequency | update-type { combined-update | imsi-combined-update | periodic | ra-update } ] [ access-type { gprs | umts } | frequency frequency ][ no | remove ] ptmsi-signature-reallocate { attach | frequency | interval | routing-area-update [ update-type { combined-update | imsi-combined-update | periodic | ra-update } ] } [ access-type { gprs | umts } ]
no
Disables the authentication
procedures configured for the specified P-TMSI signature reallocation
configuration in the call control profile.
remove
Deletes the defined
authentication procedures for the specified P-TMSI signature reallocation
configuration from the call control profile configuration file.
attach
Enables/disables
P-TMSI signature reallocation for Attach with local P-TMSI.
access-type type
One of the following
must be selected to reallocate on the basis of the type of network access:
This keyword can be
used in combination with other keywords to refine the reallocation configuration.
frequency frequency
Defines 1-in-N selective
reallocation. If the frequency is set for 12, then the SGSN skips reallocation
for the first 11 messages and reallocates on receipt of the twelfth
request message.
frequency must
be an integer from 1 to 50.
This keyword can be
used in combination with other keywords to refine the reallocation configuration.
interval minutes
Enter an integer between
1 and 1440 to define the time interval (in minutes) for skipping
the service/RAU/attach request message procedure
before performing a P-TMSI signature reallocation.
ptmsi-reallocation-command
Includes P-TMSI signature
reallocation as a part of the P-TMSI reallocation configuration.
routing-area-update [ update-type ]
Enables/disables
P-TMSI signature reallocation for RAU (routing area update) with
local P-TMSI. To refine the reallocation configuration, include
one of the optional types of updates to limit reallocation:
Usage:
By default, P-TMSI
signature reallocation is disabled. This command allows the operator to
configure when the P-TMSI signature is reallocated.
Example:
The following command
configures the SGSN to reallocate the P-TMSI signature for every third
UMTS attach procedure:
ptmsi-signature-reallocate
attach frequency 3 access-type umts
The following command
configures the SGSN to reallocate the P-TMSI signature for every seventh
GPRS periodic RAU procedure:
ptmsi-signature-reallocate
routing-area-update uupdate-type periodic frequency 7 access-type gprs
The following command
removes all configuration instances for reallocating the P-TMSI signature
based on intervals and UMTS access:
remove ptmsi-signature-reallocate
interval access-type umts
qos
Configures the quality
of service (QoS) parameters to be applied.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
qos { gn-gp } qos gn-gp { arp
high-priority priority medium-priority priority | pre-emption { capability { may-trigger-pre-emption | shall-not-trigger-pre-emption } | vulnerability { not-pre-emptable | pre-emptable } qos ue-ambr { max-ul mbr_up max-dl mbr_dl | prefer-as-cap { both-hss-and-local
minimum | local } }remove qos { gn-gp | ue-ambr }
remove
Deletes the configuration
from the call control profile.
gn-gp
Configures Gn-Gp pre-release
8 ARP and pre-emption parameters.
arp
Maps usage of ARP
(allocation/retention policy) high-priority (H) and medium-priority (M):
-
high-priority priority: Enter
an integer from 1 to 13.
-
medium-priority priority: Enter
an integer from 2 to 14.
pre-emption
Defines the pre-emption/vulnerability
criteria for PDP Contexts imported from SGSN on Gn/Gp:
-
capability
-
may-trigger-pre-emption:
PDP Contexts imported from Gn/Gp SGSN may preempt existing
bearers.
-
shall-not-trigger-pre-emption:
PDP Contexts imported from Gn/Gp SGSN shall not preempt
existing bearers.
-
vulnerability
-
not-pre-emptable:
PDP Contexts imported from Gn/Gp SGSN are not vulnerable
to pre-emption.
-
pre-emptable:
PDP Contexts imported from Gn/Gp SGSN are vulnerable to
pre-emption.
ue-ambr
This
keyword enables the operator to configure either the aggregate maximum
bit rate stored on the UE (UE AMBR) or select the preferred uplink
and downlink QoS cap values.
IMPORTANT:
The SGSN only supports
the ue-ambr keyword
beginning in Release 16.
Configures the aggregate
maximum bit rate that will be stored on the UE (user equipment).
-
max-ul mbr-up: Defines
the maximum bit rate for uplink traffic.
mbr-up: Enter
a value from 1 to 1410065408 (Release 16.1 and higher), or 0 to
1410065408.
-
max-dl mbr-down: Defines the
maximum bit rate for downlink traffic.
mbr-down: Enter
a value from 1 to 1410065408 (Release 16.1 and higher), or 0 to
1410065408.
prefer-as-cap both-hss-and-local { local-when-subscription-not-available | minimum | subscription-exceed-reject [ emm-cause-code [ eps-service-disallowed | eps-service-not-allowed-in-this-plmn | no-suitable-cell-in-tracking-area | plmn-not-allowed | roaming-not-allowed-in-this-tracking-area | tracking-area-not-allowed ] ] }
This set of options
is only available on the MME.
Specifies the QoS
cap value to use.
-
local-when-subscription-not-available: Use
the locally configured values if the Home Subscriber Server (HSS)
does not provide QoS bit rate values.
-
minimum:
Use the lower of
either the locally configured QoS bit rate or the HSS-provided QoS
bit rate. This will override the HSS provided values if it is greater
than the locally configured values, or if the HSS does not provide
any values.
-
subscription-exceed-reject:
If the requested QoS bit rate exceeds the locally configured value,
reject the PDN connection.
-
emm-cause-code:
Specifies the EPS Mobility Management (EMM) cause code to return
when the PDN connection is rejected.
-
eps-service-disallowed -
Default
-
eps-service-not-allowed-in-this-plmn
-
no-suitable-cell-in-tracking-area
-
plmn-not-allowed
-
roaming-not-allowed-in-this-tracking-area
-
tracking-area-not-allowed
Usage:
Use this command to
configure the QoS parameters for the call control profile for either the
MME or the SGSN.
On an S4-SGSN, this
command ensures proper QoS parameter mapping between the S4-SGSN
and EPC UEs, SGWs and PGWs:
-
Map EPC ARP parameters
to pre-release 8 ARP (Gn/Gp ARP) used during S4-SGSN-to-Gn
SGSN call handovers.
-
Map ARP parameters
received in a GPRS subscription from the HLR to EPC ARP parameters
if:
-
The S4 interface is
selected for an EPC capable UE, and
-
The UE has only a
GPRS subscription (but no EPS subscription) in the HLR / HSS.
Example:
Configure the Gn/Gp
interface ARP priority values:
qos gn-gp arp high-priority
2 medium-priority 3
rau-inter
Defines acceptable
parameters for inter-SGSN routing area updates.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
rau-inter { accept
use-auth-vector | access-type
gprs { all | location-area-list instance instance } { failure-code fail_code | user-device-release { before-r99 | r99-or-later } failure-code fail_code } } | allow
accept access-type gprs location-area-list instance instance | avoid-s12-direct-tunnel| ignore-peer-context-id | peer-sgsn-addr-resolution-failure
failure-code fail_code | restrict
access-type { { gprs | umts } { all | location-area-list
instance instance } }
default rau-inter ( accept
use-auth-vector | access-type { { gprs | umts } { all | location-area-list
instance instance } user-device-release { before-r99 | r99-or-later } failure-code fail_code } } | avoid-s12-direct-tunnel | failure-code fail_code | ignore-peer-context-id | peer-sgsn-addr-resolution-failure
failure-code fail_code }
no rau-inter ( accept
use-auth-vector | allow access-type { gprs | umts } location-area-list
instance instance | ignore-peer-context-id | restrict
access-type { gprs | umts } { all | location-area-list
instance instance } }
remove rau-interavoid-s12-direct-tunnel
no
Including no as part
of the command structure disables the values already configured
for parameters specified in the command.
default
Resets the configuration
of specified parameters to system default values.
remove
remove can
only be used with the avoid-s12-direct-tunnel keyword
to erase a configuration instructing the SGSN to avoid establishment
of a direct tunnel for S12 interfaces.
accept use-auth-vector
Sets the SGSN to accept
using the authorization vector.
allow access-type
Including this keyword
with one of the following options, configures the SGSN to allow MS/UE
with the identified access-type extension to be part of the intra-RAU
procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
avoid-s12-direct-tunnel
Enables the operator
to modify the Call-Control profile default configuration and instructs the
SGSN to avoid establishment of a direct tunnel for S12 interfaces.
This keyword is only
supported for configuration of S12 interfaces.
ignore-peer-context-id
Sets the SGSN to ignore
the peer's context-ID and replace with PDP context-ID information based
on the HLR subscription.
restrict access-type
Including this keyword-set
with one of the following options, configures the SGSN to restrict
MS/UE with the identified access-type extension from the
inter-RAU procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
all
all - adding
this option to the keyword determines that the failure cause code
will be applicable to all location areas.
location-area-list
instance instance
list_id must
be an integer between 1 and 5. The value must be an already defined
instance of a location area code (LAC) list created with the location-area-list command.
failure-code fail-code
Specify a GSM Mobility
Management (GMM) failure cause code to identify the reason an inter
SGSN RAU does not occur. This GMM cause code will be sent in the
reject message to the MS.
fail-code must
be an integer from 2 to 111. Refer to the GMM failure cause codes
listed below (from section 10.5.5.14 of the 3GPP TS 124.008 v7.2.0
R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 -MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
user-device-release { before-r99 | r99-or-later } failure-code code
Default: Disabled
Enables the SGSN to
reject an Inter-RAU procedure based on the detected 3GPP release version
of the MS equipment and selectively send a failure cause code in
the reject message. The SGSN uses the following procedure to implement
this configuration:
-
When Attach Request
is received, the SGSN checks the subscriber’s IMSI and current
location information.
-
Based on the IMSI,
an operator policy and call control profile is found that relates
to this Attach Request.
-
call control profile
is checked for access limitations.
- Attach Request is
checked to see if the revision indicator bit is set
-
if not, then the configured
common failure code for reject is sent;
-
if set, then the 3GPP
release level is verified and action is taken based on the configuration
of this parameter
One of the following
options must be selected and completed:
-
before-r99:
Indicates the MS would be a 3GPP release prior to R99 and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
-
r99-or-later:
Indicates the MS would be a 3GPP Release 99 or later and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
Usage:
Use this command to
configure the restrictions and function of the inter-RAU procedure.
Example:
Configure default
inter-RAU settings for Edge calls from subscribers on location-area-list no.
1:
default rau-inter allow
access-type gprs location-area-list instance 1
rau-inter-plmn
Enables or disables
restriction of all Routing Area Updates (RAUs) occurring between
different PLMNs.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
rau-inter-plmn access-type { all | location-area-list
instance instance } { failure-code fail_code | user-device-release { before-r99 } failure-code fail_code | r99-or-later } { failure-code fail_code } }default rau-inter-plmn
access-type { all | location-area-list instance instance} user-device-release { before-r99
failure-code | r99-or-later failure-code }[ no ] rau-inter-plmn { restrict | allow } access-type { gprs | umts } { all | location-area-list
instance instance }[ no ] rau-inter-plmn { allow
access-type | restrict access-type } { [ all ] failure-code fail_code | location-area-list instance instance }default rau-inter { allow
access-type | restrict access-type } { [ all ] failure-code fail_code | location-area-list instance instance } }
no
Including “no” as
part of the command structure disables the values already configured
for parameters specified in the command.
default
Resets the configuration
of specified parameters to system default values.
allow access-type
Including this keyword-set
with one of the following options, configures the SGSN to allow MS/UE
with the identified access-type extension to be part of the intra-RAU
procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
restrict access-type
Including this keyword-set
with one of the following options, configures the SGSN to restrict
MS/UE with the identified access-type extension from the
inter-RAU procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
all
all - adding
this option to the keyword determines that the failure cause code
will be applicable to all location areas.
location-area-list
instance instance
list_id must
be an integer between 1 and 5. The value must be an already defined
instance of a LAC list created with the location-area-list command.
failure-code fail-code
Specify a GSM Mobility
Management (GMM) failure cause code to identify the reason an inter
SGSN RAU does not occur. This GMM cause code will be sent in the
reject message to the MS.
fail-code must
be an integer from 2 to 111. Refer to the GMM failure cause codes
listed below (from section 10.5.5.14 of the 3GPP TS 124.008 v7.2.0
R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 -MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
user-device-release { before-r99 | r99-or-later } failure-code code
Default: Disabled
Enables the SGSN to
reject an Inter-RAU procedure based on the detected 3GPP release version
of the MS equipment and selectively send a failure cause code in
the reject message. The SGSN uses the following procedure to implement
this configuration:
-
When Attach Request
is received, the SGSN checks the subscriber’s IMSI and
current location information.
-
Based on the IMSI,
an operator policy and call control profile are found that relate
to this Attach Request.
-
The call control profile
is checked for access limitations.
- Attach Request is
checked to see if the revision indicator bit is set
-
if not, then the configured
common failure code for reject is sent;
-
if set, then the 3GPP
release level is verified and action is taken based on the configuration
of this parameter
One of the following
options must be selected and completed:
-
before-r99:
Indicates the MS would be a 3GPP release prior to R99 and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
-
r99-or-later:
Indicates the MS would be a 3GPP Release 99 or later and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
Usage:
Use this command to
configure the restrictions and function of the inter-RAU procedure occurring
across RNCs or BSSs where the PLMN changes. For example:
-
inter-IuPS RAU, where
the two IuPSs have different PLMNs
-
inter-GPRS RAU, where
the two GPRSs have different PLMNs
-
inter-RAT RAU (2G >
3G), where the IuPS/GPRS services have different PLMNs
-
inter-RAT-RAU (3G >
2G), where the IuPS/GPRS services have different PLMNs
Example:
default rau-inter allow
access-type gprs location-area-list instance 1
rau-intra
Defines an acceptable
procedure for intra-SGSN Routing Area Updates (RAUs).
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
rau-intra access-type { all | location-area-list instance instance } { failure-code fail_code | user-device-release { before-r99 } { failure-code fail_code | r99-or-later } { failure-code fail_code } }default rau-intra
access-type { all | location-area-list instance instance} user-device-release { before-r99
failure-code | r99-or-later failure-code }rau-intra { allow
access-type | restrict access-type } { [ all ] failure-code fail_code | location-area-list
instance instance } }no rau-intra { allow
access-type | restrict access-type } { [ all ] failure-code fail_code | location-area-list
instance instance }default rau-intra { allow
access-type | restrict access-type } { [ all ] failure-code fail_code | location-area-list
instance instance } }
no
Including “no” as
part of the command structure disables the values already configured
for parameters specified in the command.
default
Resets the configuration
of specified parameters to system default values.
allow access-type
Including this keyword-set
with one of the following options, configures the SGSN to allow an
MS/UE with the identified access-type extension to be part
of the intra-RAU procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
restrict access-type
Including this keyword-set
with one of the following options, configures the SGSN to restrict
an MS/UE with the identified access-type extension from
the intra-RAU procedure.
-
gprs - General
Packet Radio Service
-
umts - Universal
Mobile Telecommunications System
all
all - adding
this option to the keyword determines that the failure cause code
will be applicable to all location areas.
location-area-list
instance instance
list_id must
be an integer between 1 and 5. The value must be an already defined
instance of a location area code (LAC) list created via the location-area-list command.
failure-code fail-code
Specify a GSM Mobility
Management (GMM) failure cause code to identify the reason an inter
SGSN RAU does not occur. This GMM cause code will be sent in the
reject message to the MS.
fail-code must
be an integer from 2 to 111. Refer to the GMM failure cause codes
listed below (from section 10.5.5.14 of the 3GPP TS 124.008 v7.2.0
R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 -MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
user-device-release { before-r99 | r99-or-later } failure-code code
Default: Disabled
Enables the SGSN to
reject an Intra-RAU procedure based on the detected 3GPP release version
of the MS equipment and selectively send a failure cause code in
the reject message. The SGSN uses the following procedure to implement
this configuration:
-
When Attach Request
is received, the SGSN checks the subscriber’s IMSI and
current location information.
-
Based on the IMSI,
an operator policy and call control profile are found that relate
to this Attach Request.
-
Call control profile
is checked for access limitations.
- Attach Request is
checked to see if the revision indicator bit is set
-
if not, then the configured
common failure code for reject is sent;
-
if set, then the 3GPP
release level is verified and action is taken based on the configuration
of this parameter
One of the following
options must be selected and completed:
-
before-r99:
Indicates the MS would be a 3GPP release prior to R99 and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
-
r99-or-later:
Indicates the MS would be a 3GPP Release 99 or later and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111.
Usage:
Use this command to
configure the restrictions and function of the intra-RAU procedure.
Example:
default rau-intra allow
access-type gprs location-area-list instance 1
re-authenticate
Enables or disables
the re-authentication feature.
This
command is available in releases 8.1 and higher.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
re-authenticate [ access-type { gprs | umts } ]remove re-authenticate
remove
Including this keyword
with the command disables the feature. The feature is disabled by default.
access-type
Defines the type of
access to be allowed or restricted.
If this keyword is
not included, then both access types are allowed by default.
Usage:
Use this command to
enable or disable the re-authentication feature, which instructs
the SGSN to retry authentication with another RAND in situations
where failure of the first authentication has occurred. To address
the introduction of new SIM cards, for security reasons a systematic
"last chance" authentication retry with a fresh Authentication Vector
is needed, particularly in cases where there is an SRES mismatch
at authentication.
regional-subscription-restriction
Allows the operator
to define the cause code for subscriber rejection when it is due
to regional subscription information failure.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] regional-subscription-restriction [ failure-code code | user-device-release { before-r99
failure-code code | r99-or-later
failure-code code } ]
remove
This keyword causes
the configuration to be deleted from the call control profile configuration.
failure-code cause_code
cause_code: Enter
an integer from 2 to 111; default code is 13 (roaming not allowed
in this location area [LA]).
Refer to the GMM failure
cause codes listed below (from section 10.5.5.14 of the 3GPP TS 124.008
v7.2.0 R7):
-
-
-
-
7 - GPRS services
not allowed
-
8 - GPRS services
and non-GPRS services not allowed
-
9 - MSID cannot be
derived by the network
-
-
-
12 - Location Area
not allowed
-
13 - Roaming not allowed
in this location area
-
14 - GPRS services
not allowed in this PLMN
-
15 - No Suitable Cells
In Location Area
-
16 - MSC temporarily
not reachable
-
-
-
-
-
23 - GSM authentication
unacceptable
-
40 - No PDP context
activated
-
48 to 63 - retry upon
entry into a new cell
-
95 - Semantically
incorrect message
-
96 - Invalid mandatory
information
-
97 - Message type
non-existent or not implemented
-
98 - Message type
not compatible with state
-
99 - Information element
non-existent or not implemented
-
100 - Conditional
IE error
-
101 - Message not
compatible with the protocol state
-
111 - Protocol error,
unspecified
user-device-release { before-r99 | r99-or-later } failure-code code
Enables the SGSN to
assign a reject cause code based on the detected 3GPP release version of
the MS equipment.
One of the following
options must be selected and completed:
-
before-r99:
Indicates the MS would be a 3GPP release prior to R99 and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111. Refer to the list above.
-
r99-or-later:
Indicates the MS would be a 3GPP Release 99 or later and an appropriate
failure code should be defined.
failure-code code: Enter
an integer from 2 to 111. Refer to the list above.
Usage:
Use this command to
define GMM reject cause codes when rejection is due to regional subscription
information failure.
Example:
The following command
sets a location area rejection message, code 12 for regional restriction
rejections:
regional-subscription-restriction
failure-code 12
reuse-authentication-triplets
Creates a configuration
entry to enable or disable the reuse of authentication triplets
in the event of a failure.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ no | remove } reuse-authentication-triplets no-limit
no
Disables this configuration
entry and disables reuse of authentication triplets.
remove
This keyword causes
the reuse configuration to be deleted from the call control profile configuration.
This is the default
behavior. Triplets are reused.
no-limit
This keyword enables
reuse triplets as needed.
Usage:
Use this command to
enable reuse of authentication triplets.
Example:
reuse-authentication-triplets
no limit
rfsp-override
Configures RAT frequency
selection priority override parameters for this call control profile.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
rfsp-override { default value | ue-val value new-val value + }remove rfsp-override { default
| ue-val value }
remove
Deletes the rfsp-override
configuration from the call control profile.
default
Restores the default
value assigned.
ue-val value
Assign the UE value
for the RAT frequency selection priority.
value: Enter
an integer from 1 to 256.
new-val value
Assign a new RFSP
Index value.
value: Enter
an integer from 1 to 256.
Multiple UE value/new
value combinations can be configured in a single command.
Usage:
Use this command to
configure the RAT frequency selection priority override parameter.
Multiple UE value/new
value combinations can be configured.
Example:
The following command
resets the specified RFSP Index value (1) to its default value, thereby
removing the RFSP Index override value previously configured:
rfsp-override default 1
rfsp-override ue-settings
Configures the override
of the RAT Frequency Selection Priority (RFSP) of matching subscribers.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] rfsp-override
ue-settings { data-centric ue-voice-domain-preference { cs-voice-only | cs-voice-preferred-ims-ps-voice-secondary | ims-ps-voice-only | ims-ps-voice-preferred-cs-voice-secondary } | voice-centric
ue-voice-domain-preference { cs-voice-only | cs-voice-preferred-ims-ps-voice-secondary | ims-ps-voice-only | ims-ps-voice-preferred-cs-voice-secondary } new-val value }
remove
Deletes the rfsp-override
configuration from the call control profile.
ue-settings value
Assign the UE value
for the RAT frequency selection priority.
data-centric ue-voice-domain-preference
Assign the UE value
for the RAT frequency selection priority for data-centric calls.
-
cs-voice-only:
Circuit switched voice only.
-
cs-voice-preferred-ims-ps-voice-secondary: Circuit
switched voice preferred.
-
ims-ps-voice-only:
IMS Packet switched voice only.
-
ims-ps-voice-preferred-cs-voice-secondary:
IMS Packet switched voice preferred.
voice-centric ue-voice-domain-preference
Assign the UE value
for the RAT frequency selection priority for voice-centric calls.
-
cs-voice-only:
Circuit switched voice only.
-
cs-voice-preferred-ims-ps-voice-secondary: Circuit
switched voice preferred.
-
ims-ps-voice-only:
IMS Packet switched voice only.
-
ims-ps-voice-preferred-cs-voice-secondary:
IMS Packet switched voice preferred.
new-val value
Assign a new RFSP
Index value.
value: Enter
an integer from 1 to 256.
Multiple UE value/new
value combinations can be configured in a single command.
Usage:
Use this command to
assign an RFSP Index for a UE based on the following factors:
- Operator policy (where
IMSI range or PLMN can influence the selected RFSP)
- UE usage setting (voice
centric, data centric)
- Voice domain preference
(CS voice only, CS voice preferred, IMS PS voice preferred, IMS PS
voice only).
To support Radio Resource
Management (RRM) in E-UTRAN, the MME provides the parameter RFSP
Index to an eNodeB across S1. The RFSP Index is used by the eNodeB
to apply specific RRM strategies.
The MME receives the
subscribed RFSP Index from the HSS, then overrides the RFSP Index
for the UE based on the settings defined in this command.
Multiple UE value/new
value combinations can be configured.
Example:
The following command
overrides the RFSP Index value for voice-centric circuit switched calls
to an RFSP Index of 10:
rfsp-override ue-setting
voice-centric voice-domain-pref cs-voice_only new-val 10
s1-reset
Configures the behavior
of user equipment (UE) on S1-reset.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
s1-reset { detach-ue | idle-mode-entry } default s1-reset
default
Reset the profile
configuration to the system default of idle-mode-entry.
detach-ue
Upon S1-reset the
MME will detach the UE.
idle-mode-entry
Upon S1-reset the
MME will move the UE to idle-mode. This is the default setting for
this command.
Usage:
Use this command to
set the MME’s reactions to an S1-reset.
Example:
Configure the MME
to put the UE into idle-mode upon receipt of S1-reset:
s1-reset idle-mode-entry
sctp-down
Configures the behavior
towards UE (user equipment) when Stream Control Transmission Protocol
(SCTP) goes down.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sctp-down { detach-ue | idle-mode-entry } default sctp-down
default
Reset the profile
configuration to the system default when SCTP layer goes down. The default
for this command is idle-mode-entry.
detach-ue
When SCTP goes down,
the MME will detach the UE.
idle-mode-entry
When the SCTP goes
down, the MME will move the UE to idle-mode. This is the default
for this command.
Usage:
Use this command to
set the MME’s reactions when the SCTP goes down.
Example:
Configure the MME
to put the UE into idle-mode when the SCTP layer goes down:
sctp-down idle-mode-entry
sgs-cause-code-mapping
Configures the
EMM reject cause code to send to a UE when an SGs cause code is
received.
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sgs-cause-code-mapping sgs-cause emm-cause-code emm_cause_coderemove sgs-cause-code-mapping sgs-cause
remove sgs-cause-code-mapping sgs-cause
Removes the configured
cause code mapping and returns it to its default value.
sgs-cause-code
Specifies the SGs cause
code received on the SGs interface to which the new cause code should
be mapped.
-
congestion -
Default mapped EMM cause code: #22 Congestion.
-
illegal-me -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
illegal-ms -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
imei-not-accepted -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
imsi-unknown-in-hlr -
Default mapped EMM cause code: #2 IMSI unknown in HSS.
-
imsi-unknown-in-vlr -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
la-not-allowed -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
network-failure -
Default mapped EMM cause code: #17 Network failure.
-
no-suitable-cells-in-la -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
plmn-not-allowed -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
protocol-error -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
roaming-not-allowed-in-la -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
service-not-subscribed -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
service-not-supported -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
-
service-out-of-order -
Default mapped EMM cause code: #16 MSC temporarily unreachable.
emm-cause-code emm_cause_code
Specifies the EPS Mobility
Management (EMM) cause code to return to the UE for the given SGs
cause code.
-
congestion
-
cs-domain-unavailable
-
imsi-unknown-in-hlr
-
msc-temp-unreachable
-
network-failure
Usage:
Use this command to
configure the EMM cause code returned to a UE when an error is reported
via the SGs inteface when attachment to the VLR has failed.
If a condition is specified
in both the call control profile associated with a call and also
the MME service, the cause configured on the call control profile
is signalled to the UE.
IMPORTANT:
EMM cause code #18 “CS
Domain not available” is not mapped to any SGs code but
is returned when SGs service is disallowed by a policy or on unexpected
behavior such as when the MME is unable to send an SGs message to
a VLR.
Related Commands
To set the cause codes
for situations where a call control profile cannot be attached to
a call (for example new-call restrictions, congestion during new
call attempt, etc.), use the local-cause-code-mapping command
in the mme-service configuration mode. This command is described
in the MME Service Configuration
Mode Commands chapter.
Example:
The following command
maps the “congestion” EMM cause code to the “network-failure” SGs
cause code:
sgs-cause-code-mapping
network-failure emm-cause-code congestion
sgsn-address
Defines the IP addresses
for peer SGSNs in a static SGSN address table. These configured
addresses can be used if operators wish to bypass DNS.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sgsn-address { nri nri | rac rac-id lac lac_id | rnc_id rnc_id } [ nri nri ] prefer { fallback-for-dns | local } address { ipv4 ip_address | ipv6 ip_address } interface { gn | s16 }no sgsn-address { ipv4 ip_address | ipv6 ip_address } { nri nri | rac rac_id lac lac_id [ nri nri | rnc_id rnc_id } [ interface { gn | s16 } ]
no
Disables the specified
peer-SGSN address configuration.
rac rac_id
Identifies the foreign
routing area code (RAC) of the peer-SGSN address to be configured
in the static peer-SGSN address table. rac_id must
be an integer from 1 to 255.
lac lac_id
Identifies the foreign
location area code (LAC) ID of the peer-SGSN address to be configured
in the static peer-SGSN address table. lac_id must
be an integer from 1 to 65535.
rnc_id rnc_id
Optional. Specifies
the target RNC ID that maps to the address of the peer SGSN via
the S16 interface. The RNC ID is used by the S4-SGSN for inter-SGSN
SRNS relocations. Valid entries are 1 to 65535. This setting only
applies if SRNS relocation has been configured via the srns-inter and/or srns-intra commands
in Call Control Profile
Configuration Mode.
nri nri
Identifies the network
resource identifier stored in the P-TMSI (bit 17 to bit 23). nri must
be an integer from 0 to 63.
IMPORTANT:
Typically, use of this
keyword is optional. However, it must be included in the command when
Flex (SGSN-Pooling) is implemented.
Note:
Look up for peer SGSN
in the local pool can be performed by configuring only the NRI
value, as the NRI value is unique in a pool.
prefer { fallback-for-dns | local }
Indicates the preferred
source of the address to be used.
-
fallback-for-dns -
Instructs the SGSN to perform a DNS query to get the IP address
of the peer-SGSN. If the DNS query fails, then the IP address configured
with this command is used.
-
local -
instructs the system to use the local IP address configured with
this command.
IMPORTANT:
If the prefer command
is used to change an existing sgsn-address configuration (with the
same LAC and RAC) from fallback-for-dns to local or from local to fallback-for-dns,
the new setting overwrites the previously configured setting for
all interfaces.
address { ipv4 ip_address | ipv6 ip_address }
Specifies the IP address
of the peer SGSN. Currently, the IPv6 address option is not supported
on the S4-SGSN.
-
ipv4 ip_address -
specifies a valid address in IPv4 dotted-decimal notation.
-
IMPORTANT:
The ipv6 option
is under development for future use and is not supported in this
release.
interface { gn | s16 }
interface -
optional. Specifies the interface type used for communicating with
the peer SGSN. Must be one of the following:
-
gn specifies
that communication will occur over the Gn interface with a peer
SGSN configured for 2.5G, 3G, or dual access SGSN services.
-
s16 specifies
that communication will occur over the S16 interface with a peer
S4-SGSN.
Usage:
Use this command to
save time by avoiding DNS. This command enables a local mapping by
setting the peer-SGSN IP address to be used for inter-SGSN Attach
and inter-SGSN-RAU. When configured, if the SGSN receives a RAU
or an Attach Request with a P-TMSI and an old-RAI that is not local,
the SGSN consults this table and uses the configured IP address
instead of resolving via DNS. If this table is not configured, then
IP address resolution is done using DNS.
The MCC and MNC of the
RAI are taken from the IMSI range configured in the operator policy
and the LAC and RAC are configured here in the call control profile
configuration mode.
The sgsn-address command
differs from other Call Control Profile configuration mode commands
in the following ways:
-
Within the SGSN’s
call logic, all other configuration elements defined with the other
commands in this mode are used
after the IMSI
is learnt. The configuration defined with this command is part of
the decision logic
prior to the
IMSI being known.
-
With the peer-SGSN address
configured using this
sgsn-address command,
the peer-SGSN-RAI’s MCC/MNC is used as a 5 or
6-digit IMSI and the operator policy and call control profile selection
are completed.
IMPORTANT:
Typically, use of this
command is optional. However, it must be included in the configuration when
Flex (SGSN-Pooling) is implemented if (1) the SGSN functions as
a default SGSN, then configure the local-NRI of other SGSN with
this command; or if (2) another SGSN is offloading, then configure
the NB-RAI/null-NRI of the peer-SGSN with this command.
Example:
Create a local peer-SGSN
address mapping of an RAI with RAC of
123 and LAC
of
4444 and
an
IPv4 address
of
123.11.313.11 for
the peer-SGSN:
sgsn-address rac 123
lac 4444 local address ipv4 123.11.313.11
sgsn-core-nw-interface
This command enables
operators to select the Gn interface or the S4 interface for EPC
capable UEs on the S4-SGSN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sgsn-core-nw-interface { gn | s4 }
sgsn-core-nw-interface { gn | s4 }
Specifies the interface
that EPC-capable UEs will use to communicate wit the packet core gateways
(GGSN/SGW). Selection must be one of:
-
gn: Forces
the SGSN to forcefully select the Gn interface for EPC-capable UEs.
-
s4: Specifies
that the SGSN will use the S4 interface between the S4-SGSN and
packet core gateways (GGSN/SGW). This is the default setting
for EPC-capable UEs.
Usage:
Use this command to
forcefully select the interface that the SGSN will use for EPC-capable
UEs.
This command is available
only if the SGSN S4
Interface license is enabled on the SGSN.
Example:
sgsn-core-nw-interface gn
sgsn-number
Defines the SGSN’s
E.164 number to be used for interactions via the Mobile Application
Part (MAP) protocol. E.164 is an ITU-T recommendation that defines
the international public telecommunication numbering plan used in
public switched telephone networks (PSTN) and some other data networks.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sgsn-number E164_numberno sgsn-number
no
Disables the use of
this configuration definition.
E164_number
Specifies a string
of 1 to 16 digits that serve as the SGSN’s E.164 identification.
Usage:
This command configures
the current SGSN E164 contact number.
The SGSN number configured
for a call control profile is related to the SGSN number configured
in the SGSN service configuration and/or in the GPRS service
configuration. If the SGSN number is not configured as part of the
call control profile configuration, then the SGSN number defined
as part of the SGSN service or GPRS service configuration is used.
When the 3G SGSN supports
multiple PLMNs configured through different IuPS services or when
network sharing is implemented, then it may be required to use different
SGSN numbers for each PLMN. In such cases, configure the per-PLMN
SGSN number in a call control profile. SGSN number definition for
a call control profile allows emulation of a different SGSN to each
HLR per PLMN. SGSN number definitions in the call control profile
also enable the SGSN to use a different SGSN number per operator
when network sharing is implemented.
Example:
Map the E.164 number
198765432123456 for
the SGSN to this call control profile configuration:
sgsn-number 198765432123456
sgtp-service
Identifies the SGTP
service configuration to be used according to this call control profile.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
sgtp-service context ctxt_name service sgtp_service_nameno sgtp-service context
context ctxt_name
Specifies the SGTP
context as an alphanumeric string of 1 through 64 characters.
service sgtp_service_name
Specifies the SGTP
service name as an alphanumeric string of 1 through 64 characters.
no
Disables use of SGTP
service.
Usage:
Use this command to
configure enabling or disabling of SGTP service for this call control profile.
Example:
sgtp-service context
sgtp1 service sgtp-srvc1
sms-mo
Configures how mobile-originated
(MO) short message service (SMS) messages are handled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] sms-mo { { access-type { gprs | umts } { all-location-areas | location-area-list } | allow
access-type { gprs | umts } | restrict
access-type { gprs | umts } }
remove
Deletes the specified
configuration.
access-type type
Access by SMS will
be limited to SMS coming from this network type:
allow
Allow either GPRS
or UMTS type access for SMS.
restrict
Restrict either GPRS
or UMTS type access for SMS.
location-area-list
instance instance
instance must
be an integer between 1 and 5. The value must identify an already
defined location area code (LAC) list created with the location-area-list command.
failure-code code
code: Must
be an integer from 2 to 111.
Usage:
Configure filtering
for SMS-MO messaging.
Example:
sms-mo access-type
gprs all-location-areas failure-code 100
sms-mt
This command configures
how mobile-terminated (MT) short message service (SMS) messages
are handled.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] sms-mt { { access-type { gprs | umts } { all-location-areas | location-area-list } | allow
access-type { gprs | umts } | restrict
access-type { gprs | umts } }
remove
Deletes the specified
configuration.
access-type type
Access by SMS will
be limited to SMS coming from this network type:
allow
Allow either GPRS
or UMTS type access for SMS.
restrict
Restrict either GPRS
or UMTS type access for SMS.
location-area-list
instance instance
instance must
be an integer between 1 and 5. The value must identify an already
defined LAC list created with the location-area-list command.
failure-code code
code: Must
be an integer from 2 to 111.
Usage:
Configure filtering
for SMS-MT messaging.
Example:
sms-mt access-type
gprs all-location-areas failure-code 100
srns-inter
Defines handling parameters
for Inter-SRNS (Serving Radio Network Subsystem) relocation.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
srns-inter ( all failure-code | allow
location-area-list instance instance | location-area-list
instance instance failure-code code | restrict
location-area-list instance instance }no srns-inter { allowlocation-area-list
instance instance | restrictlocation-area-list
instance instance }default srns-inter { all | location-area-list-instance instance }
no
Deletes the inter-SRNS
relocation configuration.
default
Resets the configuration
to default values.
all failure-code code
Define the failure
code that will apply to all inter-SRNS relocations.
code: Must
be an integer from 2 to 111.
allow location-area-list
instance instance
Identify the location
area list Id (LAC Id) that will allow services in the defined location area.
location-area-list
instance instance
instance:
Must be an integer between 1 and 5 that identifies the previously
defined location area list created with the location-area-list command.
restrict location-area-list
instance instance
Identify the location
area list Id (LAC Id) that indicates the location areas where services will
be restricted.
Usage:
This command defines
the operational parameters for inter-SRNS relocation.
Example:
The following command
allows services in areas listed in LAC list #3:
srns-inter allow location-area-list
instance 3
srns-intra
Defines handling parameters
for intra-SRNS (Serving Radio Network Subsystem) relocation.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
srns-intra ( all failure-code | allow
location-area-list instance instance | location-area-list
instance instance failure-code code | restrict location-area-list
instance instance }no srns-intra { allow
location-area-list instance instance | restrictlocation-area-list
instance instance }default srns-intra { all | location-area-list-instance instance }
no
Deletes the intra-SRNS
relocation configuration.
default
Resets the configuration
to default values.
all failure-code code
Define the failure
code that will apply to all intra-SRNS relocations.
code: Must
be an integer from 2 to 111.
allow location-area-list
instance instance
Identify the location
area list Id (LAC Id) that will allow services in the defined location area.
location-area-list
instance instance
instance:
Must be an integer between 1 and 5 that identifies the previously
defined location area list created with the location-area-list command.
restrict location-area-list
instance instance
Identify the location
area list Id (LAC Id) of the target RNC to determine the location
areas where services will be restricted.
Usage:
This command defines
the operational parameters for intra-SRNS relocation.
Example:
The following command
restricts service in areas listed in the LAC list 1:
srns-intra restrict
location-area-list instance 1
srvcc exclude-stnsr-nanpi
Configures the MME
to not include the
Nature of Address and Numbering Plan Indicator (NANPI) in the Session
Transfer Number for Single Radio Voice Call Continuity (STN-SR)
IE on Sv interface in PS to CS requests to the MSC server and Forward Relocation
requests to the peer-SGSN/peer-MME.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] srvcc
exclude-stnsr-nanpi
remove
Deletes this configuration
from the call control profile. This returns the MME to its default configuration
where the NANPI is not included in the STN-SR IE.
Usage:
This command applies
to Release 15.0 MR3 and higher.
In Release 15.0 MR3
and later releases, the encoding of the STN-SR IE on Sv interface now
includes the NANPI from the HSS in PS to CS requests to the MSC
server and Forward Relocation requests to the peer-SGSN/peer-MME.
The value of NANPI sent by the MME is 0x11. This change in behavior
is provided in support of TS 29.280 V10.1.0.
This command provides
an option to maintain backward compatibility. When this command
is issued, the MME excludes the NANPI from these requests, as was
the default in releases prior to 15.0 MR3.
subscriber-control-inactivity
Configures \the
subscriber-control inactivity timer. The system detects inactivity when
no PDP context is activated and starts the timer.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
subscriber-control-inactivity
timeout minutes time detach { immediate | next-connection | reattach-time-period }{ no | default } subscriber-control-inactivity
no
Deletes the timer
configuration.
default
Resets the timer configuration
to the default value of 7 days (10080 minutes).
timeout minutes time[ detach ]
Sets the number of
minutes the SGSN monitors the connection after inactivity has been detected.
When the timer expires, the subscribe will be detached.
time: Enter
an integer from 1 to 20160 (two weeks).
detach [ immediate | next-connection | reattach-time-period ]
Instructs the SGSN
to detach and can be configured to specify when the detach will
occur after inactivity is detected. To fine-tune the detach instruction,
include one of the following with the command:
-
immediate -
Instructs the SGSN to detach immediately after inactivity is detected.
May combine with
reattach-time-period.
-
next-connection -
instructs the SGSN to detach after the next Iu connection after
inactivity is detected.
IMPORTANT:
Supported for 3G SGSNs
only.
-
reattach-time-period period[ action ] - Specify
the number of seconds the SGSN will monitor a new re-attach after
the previous detach was due to inactivity. Also, you can define
the action to be taken regarding new attaches.
period: Enter
an integer from 60 to 3600.
action -
Select an action:
-
-
permit-and-stop-monitoring
Usage:
Use this command to
configure the timeout timer. After this timer times out the subscriber is
detached from the SGSN.
Example:
The following command
instructs the SGSN to monitor the connection for up to
360 minutes
after inactivity is detected, or detach immediately after inactivity
is detected:
subscriber-control-inactivity
timeout minutes 360 detach immediate
super-charger
Enables or disables
the SGSN to work with a super-charged network.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] super-charger
remove
Disables the super-charger
functionality.
Usage:
By enabling the super
charger functionality for 2G or 3G connections controlled by an operator
policy, the SGSN changes the hand-off and location update procedures
to reduce signalling traffic management.
Example:
The following command
enables the super charger feature:
super-charger
tau
Configure parameters
for the tracking area update (TAU) procedure.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
tau { imei-query-type { imei | imei-sv | none } [ verify-equipment-identity [ allow-on-eca-timeout | deny-greylisted | deny-unknown | verify-emergency ] ] | inter-rat
security-ctxt { allow-mapped | native } }remove tau { imei-query-type | inter-rat
security-ctxt }
remove
Deletes this TAU configuration
from the call control profile.
imei-query-type { imei | imei-sv | none }
This keyword set is specific
to the MME.
Sets the IMEI query-type
if an IMEI (International Mobile Equipment Identity) is not already
present.
-
imei: Specifies
that the MME is required to query the UE for its International Mobile
Equipment Identity (IMEI).
-
imei-sv: Specifies
that the MME is required to query the UE for its International Mobile
Equipment Identity - Software Version (IMEI-SV).
-
none: Specifies
that the MME does not need to query for IMEI or IMEI-SV.
verify-equipment-identity [ allow-on-eca-timeout | deny-greylisted | deny-unknown | verify-emergency ]
Specifies that the identification
(IMEI or IMEI-SV) of the UE is to be performed by the Equipment
Identity Register (EIR) over the S13 interface.
-
allow-on-eca-timeout:
Configures the MME to allow equipment that has timed-out on ECA
during the attach procedure.
-
deny-greylisted:
Configures the MME to deny grey-listed equipment during the attach
procedure.
-
deny-unknown:
Configures the MME to deny unknown equipment during the attach procedure.
-
verify-emergency:
Configures the MME to ignore the IMEI validation of the equipment
during the attach procedure in emergency cases. This keyword is
only supported in release 12.2 and higher.
inter-rat security-ctxt { allow-mapped | native }
Configure inter-RAT
parameters for TAU. This keyword provides the operator with the option
of continuing with the mapped context or creating a new native context
after an inter-RAT handover.
-
allow-mapped:
Configures inter-RAT security-context type as mapped. Mapped security
context is allowed after inter-RAT handover. This is the default
value.
-
native: Configures
inter-RAT security-context type as native only. Inter-RAT handover
will always result in a native security context.
Usage:
Use this command to
define tracking area update procedures such as inter-RAT security context
and IMEI query-type.
Example:
The following command
sets the IMEI query type to IMEI-SV:
tau imei-query-type imei-sv
verify-equipment- identity
treat-as-hplmn
Enables or disables
the SGSN to treat an IMSI series as coming from the home PLMN.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
[ remove ] treat-as-hplmn
remove
Deletes this configuration
from the profile. This would disable this function and is the default.
Usage:
Use this command to
enable or disable the SGSN to treat an IMSI series as coming from the
home PLMN.
Example:
The following command
disables previously configured feature:
remove treat-as-hplmn
vplmn-address
Enables/disables
the SGSN to override the VPLMN address-allowed flag.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
vplmn-address { allowed | not-allowed }
remove vplmn-address
remove
Using remove disables
the override behavior and the VPLMN-Address-Allowed flag is interpreted
as it is in the subscription data.
allowed
Using allowed instructs
the SGSN to set the VPLMN-Address-Allowed flag during GGSN seletion
- even if the flag was not received in the subscription data from
the HLR.
not-allowed
Using not-allowed instructs
the SGSN not to set the VPLMN-Address-Allowed flag during GGSN seletion
- even if the flag is received in the subscription data from the
HLR.
Usage:
Use this command to
override the VPLMN-Address-Allowed flag received in subscription data
from HLR during GGSN selection. This flag is used to decide whether
to use the VPLMN-OI received from a roaming subscriber to form the
full-APN. The full-APN is then used in a DNS query to select a GGSN.
This override enables the operator to control selection of a different
GGSN for a roaming subscriber by using/not-using VPLMN-OI
in full-APN.
Example:
The following command
instructs the SGSN to set the VPLMN-Address-Allowed flag during
GGSN selection, even if the flag was not received in subscription
data from the HLR:
vplmn-address allowed
The following command
instructs the SGSN not to set the VPLMN-Address-Allowed flag during
GGSN selection, even if the flag was received in subscription data
from the HLR:
vplmn-address not-allowed
The following command
instructs the SGSN not to override standard behavior regarding the VPLMN-Address-Allowed
flag:
remove vplmn-address
zone-code
Configures a zone
code listing of one or more location area code (LACs) included in
the zone.
Privilege:
Security Administrator,
Administrator
Mode:
Exec > Global Configuration
> Call Control Profile Configuration
configure > call-control-profile profile_name
Entering the above
command sequence results in the following prompt:
[local]host_name(config-call-control-profile-profile_name)#
Syntax
zone-code zc_id location-area-code lac
no zone-code zc_id [ location-area-code lac ]
no
Removes either a specific
LAC from the zone code list. If the location-area-code parameter
is not included in the command, then the entire zone code list definition
is removed from configuration.
zc_id
Identifies an instance
of a zone code list as an integer from 1 to 65535.
An unlimited number
of zone code lists can be configured per call control profile as
the zone code lists are allocated dynamically. A maximum of 10 zone
code lists can be configured per Call Control Profile.
location-area-code lac
Prompts for the location
area-code(s), where the subscribers can roam, that are part of the zone. lac is an
integer from 1 to 65535.
Repeat the command
with this parameter to include up to 100 LACs in the zone code list.
Usage:
IMPORTANT:
While there is no
limit to the number of zone codes that can be created, only 10 LACs
per zone code can be defined.
Use this command to
define zone code restrictions. Regional subscription data at the
home location register (HLR) is used to determine the regional subscription
area in which the subscriber is allowed to roam. The regional subscription
data consists of a list of zone codes. A zone code is comprised
of one or more location areas (identified by a LAC) into which the subscriber
is allowed to roam. Regional subscription data, if present in the
insert subscriber data (ISD) request from the HLR, defines the subscriber's
subscription area for the addressed SGSN. It contains the complete
list (up to 10 zone codes) that apply to a subscriber in the currently visited
PLMN.
During the GPRS Location
Update procedure, the zone code list is received in the ISD request
from the HLR. The zone code list from the HLR is validated against
the configured values in the operator policy. If matched, then the
ISD is allowed to proceed. If not matched, then the ISD response
is that the Network Node Area is Restricted and the GPRS Location Update
procedure fails. If no zone codes are included in the ISD (whether
or not the zone codes are defined in the SGSN configuration), then
checking is not done.
Example:
The following command
defines multiple LACs for zone code 1:
zone-code 1 lac 413
212 113