Table Of Contents
Cisco IOS Commands for Access Points
and Bridgesaccounting (SSID configuration mode)
authentication network-eap (SSID configuration mode)
authentication open (SSID configuration mode)
authentication shared (SSID configuration mode)
bridge-group block-unknown-source
bridge-group spanning-disabled
bridge-group subscriber-loop-control
clear ip proxy-mobile subnet-map
group (local server configuration mode)
guest-mode (SSID configuration mode)
infrastructure-ssid (SSID configuration mode)
ip proxy-mobile (SSID configuration mode)
match (class-map configuration)
max-associations (SSID configuration mode)
nas (local server configuration mode)
show dot11 statistics client-traffic
show interfaces dot11radio aaa
show interfaces dot11radio statistics
show ip proxy-mobile aaa requests
show ip proxy-mobile registration
show ip proxy-mobile subnet-map
show radius local-server statistics
snmp-server enable traps envmon temperature
user (local server configuration mode)
vlan (SSID configuration mode)
Cisco IOS Commands for Access Points
and Bridges
This chapter lists and describes Cisco IOS commands in Cisco IOS Release 12.2(11)JA that you use to configure and manage your access point, bridge, and wireless LAN. The commands are listed alphabetically. Refer to "List of Supported Cisco IOS Commands," for a complete list of IOS commands supported by access points and bridges.
accounting (SSID configuration mode)
Use the accounting SSID configuration mode command to enable RADIUS accounting for the radio interface (for the specified SSID). Use the no form of the command to disable accounting.
[no] accounting list-name
Syntax Description
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
You create accounting lists using the aaa accounting command. These lists indirectly reference the server where the accounting information is stored.
Examples
This example shows how to enable RADIUS accounting and set the RADIUS server name:
AP(config-if-ssid)# accounting radius1This example shows how to disable RADIUS accounting:
AP(config-if-ssid)# no accountingRelated Commands
antenna
Use the antenna configuration interface command to configure the radio receive or transmit antenna settings. Use the no form of this command to reset the receive antenna to defaults.
[no] antenna {receive | transmit} {diversity | left | right}
Syntax Description
Defaults
The default antenna configuration is diversity.
Command Modes
Configuration interface
Command History
Examples
This example shows how to specify the right receive antenna option:
AP(config-if)# antenna receive rightThis example shows how to set the receive antenna option to defaults:
AP(config-if)# no antenna receiveRelated Commands
Configures the radio transmit antenna settings
show running-config
Displays the current access point operating configuration
authentication client
Use the authentication client configuration interface command to configure a LEAP username and password that the access point uses when authenticating to the network as a repeater.
authentication client username username password password
Syntax Description
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Examples
This example shows how to configure the LEAP username and password that the repeater uses to authenticate to the network:
AP(config-if-ssid)# authentication client username ap-north password buckeyeRelated Commands
Specifies the SSID and enters the SSID configuration mode
show running-config
Displays the current access point operating configuration
authentication key-management
Use the authentication key-management SSID configuration mode command to configure the radio interface (for the specified SSID) to support authenticated key management. Cisco Centralized Key Management (CCKM) and Wi-Fi Protected Access (WPA) are the key management types supported on the access point.
authentication key-management { cckm | wpa } [ optional ]
Note
This command is not supported on bridges.
Syntax Description
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
Use this command to enable authenticated key management for client devices. To enable authenticated key management, you must enable a cipher suite using the encryption mode cipher command. To support WPA on a wireless LAN where 802.1x-based authentication is not available, you must use the wpa-psk command to configure a pre-shared key for the SSID.
Examples
This example shows how to enable CCKM for an SSID:
AP(config-if-ssid)# authentication key-management cckmRelated Commands
Specifies a cipher suite
Specifies the SSID and enters SSID configuration mode
Specifies a pre-shared key for an SSID
authentication network-eap (SSID configuration mode)
Use the authentication network-eap SSID configuration mode command to configure the radio interface (for the specified SSID) to support network-EAP authentication with optional MAC address authentication. Use the no form of the command to disable network-eap authentication for the SSID.
[no] authentication
network-eap list-name
[mac-address list-name]
Note
Syntax Description
list-name
Specifies the list name for EAP authentication
mac-address list-name
Specifies the list name for MAC authentication
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
Use this command to authenticate clients using the network EAP method, with optional MAC address screening. You define list names for MAC addresses and EAP using the aaa authentication login command. These lists define the authentication methods activated when a user logs in and indirectly identify the location where the authentication information is stored.
Examples
This example shows how to set the authentication to open for devices on a specified address list:
AP(config-if-ssid)# authentication network-eap list1This example shows how to reset the authentication to default values:
AP(config-if-ssid)# no authentication network-eapRelated Commands
authentication open (SSID configuration mode)
Use the authentication open SSID configuration mode command to configure the radio interface (for the specified SSID) to support open authentication and optionally MAC address authentication or EAP authentication. Use the no form of the command to disable open authentication for the SSID.
[no] authentication open
[mac-address list-name [alternate] ]
[eap list-name]
Note
Syntax Description
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
Use this command to authenticate clients using the open method, with optional MAC address or EAP screenings. If you use the alternate keyword, the client must pass either the MAC address or EAP authentication. Otherwise, the client must pass both authentications. You define list names for MAC addresses and EAP using the aaa authentication login command. These lists define the authentication methods activated when a user logs in and indirectly identify the location where the authentication information is stored.
Examples
This example shows how to enable open authentication with MAC address restrictions:
AP(config-if-ssid)# authentication open mac-address mac-list1This example shows how to disable open authentication for the SSID:
AP(config-if-ssid)# no authentication openRelated Commands
Specifies shared key authentication
Specifies network EAP authentication
Specifies the SSID and enters the SSID configuration mode
authentication shared (SSID configuration mode)
Use the authentication shared SSID configuration mode command to configure the radio interface (for the specified SSID) to support shared authentication with optional MAC address authentication and EAP authentication. Use the no form of the command to disable shared authentication for the SSID.
[no] authentication shared
[mac-address list-name]
[eap list-name]
Note
Syntax Description
mac-address list-name
Specifies the list name for MAC authentication
eap list-name
Specifies the list name for EAP authentication
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
Use this command to authenticate clients using the shared method, with optional MAC address or EAP screenings. You define list names for MAC addresses and EAP using the aaa authentication login command. These lists define the authentication methods activated when a user logs in and indirectly identify the location where the authentication information is stored.
Examples
This example shows how to set the authentication to shared for devices on a MAC address list:
AP(config-if-ssid)# authentication shared mac-address mac-list1This example shows how to reset the authentication to default values:
AP(config-if-ssid)# no authentication sharedRelated Commands
beacon
Use the beacon configuration interface command to specify how often the beacon contains a Delivery Traffic Indicator Message (DTIM). Use the no form of this command to reset the beacon interval to defaults.
[no] beacon {period Kms | dtim-period count}
Syntax Description
Defaults
The default period is 100.
The default dtim-period is 2.
Command Modes
Configuration interface
Command History
Usage Guidelines
Clients normally wake up each time a beacon is sent to check for pending packets. Longer beacon periods let the client sleep longer and preserve power. Shorter beacon periods reduce the delay in receiving packets.
Controlling the DTIM period has a similar power-saving result. Increasing the DTIM period count lets clients sleep longer, but delays the delivery of multicast packets. Because multicast packets are buffered, large DTIM period counts can cause a buffer overflow.
Examples
This example shows how to specify a beacon period of 15 Kms (15.36 milliseconds):
AP(config-if)# beacon period 15This example shows how to set the beacon parameter to defaults:
AP(config-if)# no beaconRelated Commands
bridge aging-time
Use the bridge aging-time global configuration command to configure the length of time that a dynamic entry can remain in the bridge table from the time the entry is created or last updated.
bridge group aging-time seconds
Note
Syntax Description
Defaults
The default aging time is 300 seconds.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the aging time for bridge group 1:
bridge(config)# bridge 1 aging-time 500Related Commands
bridge forward-time
Use the bridge forward-time global configuration command to configure the forward delay interval on the bridge.
bridge group aging-time seconds
Note
Syntax Description
Defaults
The default forward time is 30 seconds.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the forward time for bridge group 2:
bridge(config)# bridge 2 forward-time 60Related Commands
bridge hello-time
Use the bridge hello-time global configuration command to configure the interval between hello bridge protocol data units (BPDUs).
bridge group hello-time seconds
Note
Syntax Description
Defaults
The default hello time is 2 seconds.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the hello time for bridge group 1:
bridge(config)# bridge 1 hello-time 15Related Commands
bridge max-age
Use the bridge max-age global configuration command to configure the interval that the bridge waits to hear BPDUs from the spanning tree root. If the bridge does not hear BPDUs from the spanning tree root within this specified interval, it assumes that the network has changed and recomputes the spanning-tree topology.
bridge group max-age seconds
Note
Syntax Description
group
Specifies the bridge group
seconds
Specifies the max-age interval in seconds (enter a value between 10 and 200 seconds)
Defaults
The default max-age is 15 seconds.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the max age for bridge group 1:
bridge(config)# bridge 1 max-age 20Related Commands
bridge priority
Use the bridge priority global configuration command to configure the spanning tree priority for the bridge. STP uses the bridge priority to select the spanning tree root. The lower the priority, the more likely it is that the bridge will become the spanning tree root.
The radio and Ethernet interfaces and the native VLAN on the bridge are assigned to bridge group 1 by default. When you enable STP and assign a priority on bridge group 1, STP is enabled on the radio and Ethernet interfaces and on the primary VLAN, and those interfaces adopt the priority assigned to bridge group 1. You can create bridge groups for sub-interfaces and assign different STP settings to those bridge groups.
bridge group priority priority
Note
Syntax Description
group
Specifies the bridge group to be configured
priority
Specifies the STP priority for the bridge
Defaults
The default bridge priority is 32768.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the priority for the bridge:
bridge(config-if)# bridge 1 priority 900Related Commands
bridge protocol ieee
Use the bridge number protocol ieee global configuration command to enable Spanning Tree Protocol (STP) on the bridge. STP is enabled for all interfaces assigned to the bridge group that you specify in the command.
The radio and Ethernet interfaces and the native VLAN on the bridge are assigned to bridge group 1 by default. When you enable STP and assign a priority on bridge group 1, STP is enabled on the radio and Ethernet interfaces and on the primary VLAN, and those interfaces adopt the priority assigned to bridge group 1. You can create bridge groups for sub-interfaces and assign different STP settings to those bridge groups.
bridge number protocol ieee
Note
Syntax Description
Defaults
STP is disabled by default.
Command Modes
Global configuration
Command History
Examples
This example shows how to enable STP for bridge group 1:
bridge(config)# bridge 1 protocol ieeeRelated Commands
bridge-group block-unknown-source
Use the bridge-group block-unknown-source configuration interface command to block traffic from unknown MAC addresses on a specific interface. Use the no form of the command to disable unknown source blocking on a specific interface.
For STP to function properly, block-unknown-source must be disabled for interfaces participating in STP.
bridge-group group block-unknown-source
Syntax Description
Defaults
When you enable STP on an interface, block unknown source is disabled by default.
Command Modes
Configuration interface
Command History
Examples
This example shows how to disable block unknown source for bridge group 2:
bridge(config-if)# no bridge-group 2 block-unknown-sourceRelated Commands
bridge-group path-cost
Use the bridge-group path-cost configuration interface command to configure the path cost for the bridge Ethernet and radio interfaces. Spanning Tree Protocol (STP) uses the path cost to calculate the shortest distance from the bridge to the spanning tree root.
bridge-group group path-cost cost
Note
Syntax Description
Defaults
The default path cost for the Ethernet interface is 19, and the default path cost for the radio interface is 33.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure the path cost for bridge group 2:
bridge(config-if)# bridge-group 2 path-cost 25Related Commands
bridge-group port-protected
Use the bridge-group port-protected configuration interface command to enable protected port for public secure mode configuration. In IOS, there is no exchange of unicast, broadcast, or multicast traffic between protected ports.
bridge-group bridge-group
port-protectedSyntax Description
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Examples
This example shows how to enable protected port for bridge group 71:
AP(config-if)# bridge-group 71 port-protectedRelated Commands
bridge-group priority
Use the bridge-group priority configuration interface command to configure the spanning tree priority for the bridge Ethernet and radio interfaces. Spanning Tree Protocol (STP) uses the interface priority to select the root interface on the bridge.
The radio and Ethernet interfaces and the native VLAN on the bridge are assigned to bridge group 1 by default. When you enable STP and assign a priority on bridge group 1, STP is enabled on the radio and Ethernet interfaces and on the primary VLAN, and those interfaces adopt the priority assigned to bridge group 1. You can create bridge groups for sub-interfaces and assign different STP settings to those bridge groups.
bridge-group group priority priority
Syntax Description
group
Specifies the bridge group to be configured
priority
Specifies the STP priority for the bridge group
Defaults
The default priority for both the Ethernet and radio interfaces is 128.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure the priority for an interface on bridge group 2:
bridge(config-if)# bridge-group 2 priority 150Related Commands
bridge-group spanning-disabled
Use the bridge-group spanning-disabled configuration interface command to disable Spanning Tree Protocol (STP) on a specific interface. Use the no form of the command to enable STP on a specific interface.
For STP to function properly, spanning-disabled must be disabled for interfaces participating in STP.
bridge-group group spanning-disabled
Syntax Description
Defaults
STP is disabled by default.
Command Modes
Configuration interface
Command History
Examples
This example shows how to disable STP for bridge group 2:
bridge(config-if)# bridge-group 2 spanning-disabledRelated Commands
bridge-group subscriber-loop-control
Use the bridge-group subscriber-loop-control configuration interface command to enable loop control on virtual circuits associated with a bridge group. Use the no form of the command to disable loop control on virtual circuits associated with a bridge group.
For Spanning Tree Protocol (STP) to function properly, subscriber-loop-control must be disabled for interfaces participating in STP.
bridge-group group subscriber-loop-control
Syntax Description
Defaults
When you enable STP for an interface, subscriber loop control is disabled by default.
Command Modes
Configuration interface
Command History
Examples
This example shows how to disable subscriber loop control for bridge group 2:
bridge(config-if)# no bridge-group 2 subscriber-loop-controlRelated Commands
bridge-group unicast-flooding
Use the bridge-group unicast-flooding configuration interface command to enable unicast flooding for a specific interface. Use the no form of the command to disable unicast flooding for a specific interface.
bridge-group group unicast-flooding
Syntax Description
Defaults
Unicast flooding is disabled by default.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure unicast flooding for bridge group 2:
bridge(config-if)# bridge-group 2 unicast-floodingRelated Commands
broadcast-key
Use the broadcast-key configuration interface command to configure the time interval between rotations of the broadcast encryption key used for clients. Use the no form of the command to disable broadcast key rotation.
[no] broadcast-key
[vlan vlan-id]
[change secs]
[ membership-termination ]
[ capability-change ]
Note
Syntax Description
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure vlan10 to support broadcast key encryption with a 5-minute key rotation interval:
AP(config-if)# broadcast-key vlan 10 change 300This example shows how to disable broadcast key rotation:
AP(config-if)# no broadcast-keycca
Use the cca configuration interface command to configure the clear channel assessment (CCA) noise floor level for the bridge radio. The value you enter is used as an absolute value of dBm.
cca number
Note
Syntax Description
number
Specifies the radio noise floor in dBm. Enter a number from -60 to 0. Zero configures the radio to use a received validate frame as the CCA indication.
Defaults
The default CCA level is -62 dBm.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure the CCA level for the bridge radio:
bridge(config-if)# cca 50channel
Use the channel configuration interface command to set the radio channel frequency. Use the no form of this command to reset the channel frequency to defaults.
[no] channel {number | frequency | least-congested}
Syntax Description
number
Specifies a channel number. For a list of channels for the 2.4-GHz radio, see Table 2-1. For a list of channels for the 5-GHz radio, see Table 2-2.
Note
frequency
Specifies the center frequency for the radio channel. For a list of center frequencies for the 2.4-GHz access point radio, see Table 2-1. For a list of center frequencies for the 5-GHz access point radio, see Table 2-2. For a list of center frequencies for the 5-GHz bridge radio, see Table 2-3.
Note
least-congested
Enables or disables the scanning for a least busy radio channel to communicate with the client adapter
Note
Note
Defaults
The default channel is least-congested.
Command Modes
Configuration interface
Command History
Examples
This example shows how to set the access point radio to channel 10 with a center frequency of 2457.
AP(config-if)# channel 2457This example shows how to set the access point to scan for the least-congested radio channel.
AP(config-if)# channel least-congestedThis example shows how to set the frequency to the default setting:
AP(config-if)# no channelRelated Commands
show controllers dot11radio
Displays the radio controller information and status
class-map
Use the class-map global configuration command to create a class map to be used for matching packets to the class whose name you specify and to enter class-map configuration mode. Use the no form of this command to delete an existing class map and return to global configuration mode.
[no] class-map name
Syntax Description
Defaults
This command has no defaults, and there is not a default class map.
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to specify the name of the class for which you want to create or modify class-map match criteria and to enter class-map configuration mode. In this mode, you can enter one match command to configure the match criterion for this class.
The class-map command and its subcommands are used to define packet classification, marking, and aggregate policing as part of a globally named service policy applied on a per-interface basis.
After you are in quality of service (QoS) class-map configuration mode, these configuration commands are available:
•
•
•
•
•
Only one match criterion per class map is supported. For example, when defining a class map, only one match command can be issued.
Because only one match command per class map is supported, the match-all and match-any keywords function the same.
Only one access control list (ACL) can be configured in a class map. The ACL can have multiple access control entries (ACEs).
Examples
This example shows how to configure the class map called class1. class1 has one match criterion, which is an access list called 103.
AP(config)# access-list 103 permit any any dscp 10AP(config)# class-map class1AP(config-cmap)# match access-group 103AP(config-cmap)# exitThis example shows how to delete the class map class1:
AP(config)# no class-map class1You can verify your settings by entering the show class-map privileged EXEC command.
Related Commands
clear dot11 client
Use the clear dot11 client privileged EXEC command to deauthenticate a radio client with a specified media access control (MAC) address. The client must be directly associated with the access point, not a repeater.
clear dot11 client {mac-address}
Syntax Description
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to deauthenticate a specific radio client:
AP# clear dot11 client 0040.9645.2196You can verify that the client was deauthenticated by entering the following privileged EXEC command:
AP# show dot11 associations 0040.9645.2196Related Commands
Displays the radio association table or optionally displays association statistics or association information about repeaters or clients
clear dot11 hold-list
Use the clear dot11 hold-list privileged EXEC command to reset the MAC, LEAP, and EAP authentications hold list.
clear dot11 hold-list
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear the hold-off list of MAC authentications:
AP# clear dot11 hold-listclear dot11 statistics
Use the clear dot11 statistics privileged EXEC command to reset statistic information for a specific radio interface or for a particular client with a specified MAC address.
clear dot11 statistics
{interface | mac-address}Syntax Description
interface
Specifies a radio interface number
mac-address
Specifies a client MAC address (in xxxx.xxxx.xxxx format)
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear radio statistics for radio interface 0:
AP# clear dot11 statistics dot11radio 0This example shows how to clear radio statistics for the client radio with a MAC address of 0040.9631.81cf:
AP# clear dot11 statistics 0040.9631.81cfYou can verify that the radio interface statistics are reset by entering the following privileged EXEC command:
AP# show dot11 associations statisticsRelated Commands
Displays client traffic statistics
Displays radio interface information
Displays radio interface statistics
clear iapp rogue-ap-list
Use the clear iapp rogue-ap-list privileged EXEC command to clear the list of IAPP rogue access points.
clear iapp rogue-ap-list
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear the IAPP rogue access point list:
AP# clear iapp rogue-ap-listYou can verify that the rogue AP list was deleted by entering the show iapp rogue-ap-list privileged EXEC command.
Related Commands
clear iapp statistics
Use the clear iapp statistics privileged EXEC command to clear all the IAPP statistics.
clear iapp statistics
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear the IAPP statistics:
AP# clear iapp statisticsYou can verify that the IAPP statistics were cleared by entering the following privileged EXEC command:
AP# show iapp statisticsRelated Commands
clear ip proxy-mobile traffic
Use the clear ip proxy-mobile traffic privileged EXEC command to clear all the statistics related to proxy Mobile IP.
clear ip proxy-mobile traffic
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear the proxy-mobile statistics:
AP# clear ip proxy-mobile trafficYou can verify that traffic statistics are cleared by entering the show ip proxy-mobile traffic privileged EXEC command.
Related Commands
clear ip proxy-mobile subnet-map
Use the clear ip proxy-mobile subnet-map privileged EXEC command to clear the proxy Mobile IP subnet map table and obtain a new table from the AAP. If the access point cannot obtain a new table from the AAP, the subnet map table does not change. On an AAP, this command immediately synchronizes its tables with the other AAPs.
clear ip proxy-mobile subnet-map
This command has no arguments or keywords.
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to clear the proxy Mobile IP subnet map:
AP# clear ip proxy-mobile subnet-mapYou can verify that information was deleted by entering the show ip proxy-mobile subnet-map privileged EXEC command.
Related Commands
Displays the subnet map table
Displays information about proxy Mobile IP
Displays proxy Mobile IP statistics, the subnet map table, and all the security associations
concatenation
Use the concatenation configuration interface command to enable packet concatenation on the bridge radio. Using concatenation, the bridge combines multiple packets into one packet to reduce packet overhead and overall latency, and to increase transmission efficiency.
concatenation [ bytes ]
Note
Syntax Description
bytes
(Optional) Specifies a maximum size for concatenated packets in bytes. Enter a value from 1600 to 4000.
Defaults
Concatenation is enabled by default, and the default maximum concatenated packet size is 3500.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure concatenation on the bridge radio:
bridge(config-if)# concatenation 4000countermeasure tkip hold-time
Use the countermeasure tkip hold-time configuration interface command to configure a TKIP MIC failure holdtime. If the access point detects two MIC failures within 60 seconds, it blocks all the TKIP clients on that interface for the holdtime period.
countermeasure tkip hold-time seconds
Syntax Description
seconds
Specifies the length of the TKIP holdtime in seconds (if the holdtime is 0, TKIP MIC failure hold is disabled)
Defaults
TKIP holdtime is enabled by default, and the default holdtime is 60 seconds.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure the TKIP holdtime on the access point radio:
ap(config-if)# countermeasure tkip hold-time 120debug dot11
Use the debug dot11 privileged EXEC command to begin debugging of radio functions. Use the no form of this command to stop the debug operation.
[no] debug dot11
{events | packets | forwarding | mgmt | network-map | syslog | virtual-interface}Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging of all radio-related events:
AP# debug dot11 eventsThis example shows how to begin debugging of radio packets:
AP# debug dot11 packetsThis example shows how to begin debugging of the radio system log:
AP# debug dot11 syslogThis example shows how to stop debugging of all radio related events:
AP# no debug dot11 eventsRelated Commands
show debugging
Displays all debug settings and the debug packet headers
Displays configuration and status information for the radio interface
debug dot11 aaa
Use the debug dot11 aaa privileged EXEC command to begin debugging of dot11 authentication, authorization, and accounting (AAA) operations. Use the no form of this command to stop the debug operation.
[no] debug dot11 aaa
{accounting | dispatcher |
dot1x {all | broadcast-key | process} | rxdata | state-machine | txdata} | mac-authen}Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging of dot11 AAA accounting packets:
AP# debug dot11 aaa accountingThis example shows how to begin debugging of all dot1x AAA packets:
AP# debug dot11 aaa dot1x allRelated Commands
show debugging
Displays all debug settings
Optionally displays all radio clients
debug dot11 dot11radio
Use the debug dot11 dot11radio privileged EXEC command to turn on radio debug options. These options include run RF monitor mode and trace frames received or transmitted on the radio interface. Use the no form of this command to stop the debug operation.
[no] debug dot11 dot11radio interface-number {dump | flash |
monitor {ack | address | beacon | crc | lines | plcp | print | probe | store} |
trace {lines | off | print | store}}Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin dumping of driver event packets to the logging buffer:
AP# debug dot11 dot11radio 0 dumpThis example shows how to begin debugging of the radio firmware:
AP# debug dot11 dot11radio 0 flashThis example shows how to begin monitoring of all 801.11 radio packets:
AP# debug dot11 dot11radio 0 monitorThis example shows how to stop monitoring of all radio packets:
AP# no debug dot11 dot11radio 0 monitorRelated Commands
show debugging
Displays all debug settings and the debug packet headers
Displays configuration and status information for the radio interface
Displays radio interface statistics
debug iapp
Use the debug iapp privileged EXEC command to begin debugging of IAPP operations. Use the no form of this command to stop the debug operation.
[no] debug iapp
{packets | event | error}Syntax Description
packets
Displays IAPP packets sent and received by the access point. Link test packets are not displayed
event
Displays significant IAPP events
error
Displays IAPP software and protocol errors
Defaults
This command has no default setting.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging of IAPP packets:
AP# debug iapp packetThis example shows how to begin debugging of IAPP events:
AP# debug iapp eventsThis example shows how to begin debugging of IAPP errors:
AP# debug iapp errorsRelated Commands
debug ip proxy-mobile
Use the debug ip proxy-mobile privileged EXEC command to begin debugging of proxy Mobile IP activities. If a component is not specified in the command, debugging of all components is activated. Use the no form of this command to stop the debug operation and return to the default configuration.
[no] debug ip proxy-mobile
[subnet-map] [agent-disc] [registration]Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging of all proxy-mobile activities:
AP# debug ip proxy-mobileThis example shows how to begin debugging of registration events:AP# debug ip proxy-mobile registrationThis example shows how to stop debugging of registration events:
AP# no debug ip proxy-mobile registrationYou can check debugging information by entering the show debugging privileged EXEC command.
Related Commands
debug radius local-server
Use the debug radius local-server privileged EXEC mode command to control the display of debug messages for the local authenticator.
debug radius local-server {client | error | packets }
Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging for local authenticator errors:
AP# debug radius local-server errorRelated Commands
Enables the access point as a local authenticator
show debugging
Displays all debug settings and the debug packet headers
debug wlccp
Use the debug wlccp privileged EXEC command to enable debugging for devices that interact with the access point that provides wireless domain services (WDS).
debug wlccp
ap { mn | wds-discovery | state }
packet
wds [ state | statistics ]
Note
Syntax Description
Defaults
Debugging is not enabled.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to begin debugging for LEAP-enabled client devices participating in Cisco Centralized Key Management (CCKM):
AP# debug wlccp ap mnRelated Commands
show debugging
Displays all debug settings and the debug packet headers
Displays WLCCP information
distance
Use the distance configuration interface command to specify the distance from a root bridge to the non-root bridge or bridges with which it communicates. The distance setting adjusts the bridge's timeout values to account for the time required for radio signals to travel from bridge to bridge. If more than one non-root bridge communicates with the root bridge, enter the distance from the root bridge to the non-root bridge that is farthest away. You do not need to adjust this setting on non-root bridges.
distance kilometers
Note
Syntax Description
Defaults
In installation mode, the default distance setting is 99 km. In all other modes, such as root and non-root, the default distance setting is 0 km.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure the distance setting for the root bridge radio:
bridge(config-if)# distance 40dot11 adjacent-ap age-timeout
Use the dot11 adjacent-ap age-timeout global configuration command to specify the number of hours an inactive entry remains in the list of adjacent access points.
dot11 adjacent-ap age-timeout hours
Note
Syntax Description
Defaults
The default age-timeout is 24 hours.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure the timeout setting for inactive entries in the adjacent access point list:
AP# dot11 adjacent-ap age-timeout 12Related Commands
dot11 antenna-alignment
Use the dot11 antenna-alignment privileged EXEC command to activate the antenna-alignment tool for an radio interface. Use this tool to test and align the access point antenna with another remote antenna.
dot11 interface-number antenna-alignment [timeout]
Syntax Description
interface-number
Specifies the radio interface number (The 2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.)
timeout
Specifies the duration of the alignment test, in seconds
Defaults
The default alignment timeout is 5 seconds.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
During the antenna alignment test, the radio disassociates from its parent, probes adjacent access points, and records the MAC address and signal strength of responses it receives. After the timeout, the radio reassociates with its parent. Clients connected to the access point through its parent lose their connection for the duration of the test; clients connected to a repeater maintain their connection and can abort the test using the escape sequence (Ctrl key and ^ key).
You display the last 10 results using the show dot11 antenna-alignment command, which lists the MAC address and signal level for the access points that responded to the probe.
Examples
This example shows how to start the antenna-alignment test for radio interface 0:
AP# dot11 dot11radio 0 antenna-alignmentRelated Commands
dot11 carrier busy
Use the dot11 carrier busy privileged exec command to display levels of radio activity on each channel.
dot11 interface-number carrier busy
Syntax Description
interface-number
Specifies the radio interface number (The 2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.)
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
During the carrier busy test, the access point or bridge drops all associations with wireless networking devices for about 4 seconds while it conducts the carrier test and then displays the test results.
You can re-display the carrier busy results using the show dot11 carrier busy command.
Examples
This example shows how to run the carrier busy test for radio interface 0:
AP# dot11 d0 carrier busyThis example shows the carrier busy test results:
Frequency Carrier Busy %--------- --------------5180 05200 25220 275240 55260 15280 05300 35320 2Related Commands
dot11 linktest
Use the dot11 linktest privileged EXEC command to test a radio link between the access point and a client device.
dot11 interface-number linktest
[target mac-address]
[count packet-number]
[interval sec]
[packet-size size]
[rate value]Syntax Description
Defaults
The default target for a root access point is the first client. The default target for a repeater is its parent access point.
The default count specifies that test runs once.
The default interval is 5 seconds.
The default packet-size is 512 bytes.
The default rate is the automatic rate-shifting algorithm.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The link test verifies the radio link between the access point and a client device by sending the client a series of special packets, which the client returns to the access point.
Note
The client adds information to the packets that quantify how well it received the request. Results are displayed as a table of packet statistics, quality, and signal-level information.
If you specify an interval, the test repeats continuously separated by the specified number of seconds. To abort the test, type the escape sequence (Ctrl key and ^ key). Without an interval, the test runs once.
Examples
This example shows how to initiate a radio link test to send 10 packets to client MAC address 0040963181CF on radio interface 0:
AP# dot11 dot11radio 0 linktest target 0040.9631.81CF count 10This example shows how to initiate a radio link test to send 100 packets of 500 bytes to client MAC address 0040963181CF on radio interface 0:
AP# dot11 dot11radio 0 linktest target 0040.9631.81CF packet-size 500 count 100Related Commands
Displays the radio statistics
Displays the radio association table
Displays the radio network map
dot11 meter
Use the dot11 meter privileged EXEC command to measure the performance of packet forwarding. To display the results, use the show dot11 statistics metered-traffic command.
dot11 interface-number meter
Syntax Description
interface-number
Specifies the radio interface number. The 2.4-GHz radio is radio 0. The 5-GHz radio is radio 1.
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to activate the meter tool for radio interface 0:
AP# dot11 dot11radio 0 meterRelated Commands
dot11 extension aironet
Use the dot11 extension aironet configuration interface command to enable or disable Cisco Aironet extensions to the IEEE 802.11b standard. Use the no form of this command to disable the Cisco Aironet extensions.
[no] dot11 extension aironet
Note
Syntax Description
This command has no arguments or keywords.
Defaults
Cisco Aironet extensions are disabled by default.
Command Modes
Configuration interface
Command History
Usage Guidelines
The Cisco Aironet extensions help clients choose the best access point. You must enable these extensions to use advanced features such as Cisco MIC and key hashing. Disable these extensions for non-Cisco clients that misinterpret the extensions.
Examples
This example shows how to enable Cisco Aironet extensions for the radio interface:
AP(config-if)# dot11 extension aironetThis example shows how to disable Cisco Aironet extensions for the radio interface:
AP(config-if)# no dot11 extension aironetRelated Commands
dot11 holdoff-time
Use the dot11 holdoff-time global configuration command to specify the hold-off time for MAC address authentication. Use the no form of the command to reset the parameter to defaults.
[no] dot11 holdoff-time seconds
Syntax Description
Defaults
The default holdoff-time is 0 (disabled).
Command Modes
Global configuration
Command History
Examples
This example shows how to specify a 2-minute hold-off time.
AP(config)# dot11 holdoff-time 120This example shows how reset the hold-off time to defaults.
AP(config)# dot11 no holdoff-timeRelated Commands
show running-config
Displays information on the current running access point configuration
dot11 igmp snooping-helper
Use the dot11 igmp snooping-helper global configuration command to begin sending IGMP Query requests when a new client associates with the access point. Use the no form of this command to disable the IGMP Query requests.
[no] dot11 igmp snooping-helper
Syntax Description
This command has no arguments or keywords.
Defaults
IGMP Query requests are disabled.
Command Modes
Global configuration
Command History
Examples
This example shows how to enable IGMP Query requests:
AP(config)# dot11 igmp snooping-helperThis example shows how to stop or disable the IGMP Query requests:
AP(config)# no dot11 igmp snooping-helper
dot11 network-map
Use the dot11 network-map global configuration command to enable the radio network map feature. When enabled, the access point broadcasts a IAPP GenInfo Request every collection interval. This request solicits information from all Cisco access points in the same Layer 2 domain. Upon receiving a GetInfo Request, the access point sends a unicast IAPP GenInfo Response back to the requester. The access point uses these IAPP GenInfo Responses to build a network-map.
dot11 network-map [collect-interval]
Syntax Description
Defaults
The default collect interval is 5 seconds.
Command Modes
Global configuration
Command History
Examples
This example shows how to generate a radio network map with a collection interval of 30 seconds:
AP(config)# dot11 network-map 30You can verify the network map by using the show dot11 network-map EXEC command.
Related Commands
dot11 phone
Use the dot11 phone global configuration command to enable or disable IEEE 802.11 compliance phone support. Use the no form of this command to disable the IEEE 802.11 phone.
[no] dot11 phone
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Usage Guidelines
Enabling IEEE 802.11 compliance phone support adds information to the access point beacons and probe responses. This information helps some 802.11 phones make intelligent choices about the access point to which they should associate. Some phones do not associate with an access point without this additional information.
Examples
This example shows how to enable IEEE 802.11 phone support:
AP(config)# dot11 phoneThis example shows how to stop or disable the IEEE 802.11 phone support:
AP(config)# no dot11 phone
dot11 update-group-key
Use the dot11 update-group-key privileged EXEC command to trigger an update of the WPA group key. When you enter the command, the access point distributes a new WPA group key to authenticated client devices.
dot11 interface-number update-group-key [ vlan vlan-id ]
Syntax Description
interface-number
Specifies the radio interface number (the 2.4-GHz radio is radio 0; the 5-GHz radio is radio 1)
vlan-id
Specifies the VLAN on which the access point sends out the group key update
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to trigger a group key update on VLAN 2:
AP# dot11 dot11radio 0 group-key-update vlan 2Related Commands
Configures the radio interface (for a specified SSID) to support authenticated key management
dot1x client-timeout
Use the dot1x client-timeout configuration interface command to configure the IEEE 802.1x (dot1x) client timeout value.
dot1x client-timeout 1-65555
Syntax Description
Defaults
The default timeout is 10 seconds.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure a 2-minute dot1x client timeout value:
AP(config-if)# dot1x client-timeout 120Related Commands
dot1x reauth-period
Use the dot1x reauth-period configuration interface command to configure the dot1x client- reauthentication period. The no form of the command disables reauthentication.
[no] dot1x reauth-period {1-65555 | server}
Syntax Description
Defaults
The default is disabled.
Command Modes
Configuration interface
Command History
Examples
This example shows how to configure a 2-minute dot1x client-reauthentication period:
AP(config-if)# dot1x reauth-period 120Related Commands
encryption key
Use the encryption key configuration interface command to define a WEP key used for data encryption on the wireless LAN or on a specific virtual LAN (VLAN). Use the no form of the command to remove a specific encryption key.
Note
[no] encryption
[vlan vlan-id ]
key 1-4
size {40bit | 128Bit}
encryption-key
[transmit-key]Syntax Description
vlan vlan-id
Specifies the VLAN number (1 to 4095)
key 1-4
Specifies the number of the key (1 to 4) that is being configured. (A total of four encryption keys can be configured for each VLAN.)
Note
size 40bit
Specifies a 40-bit encryption key
size 128bit
Specifies a 128-bit encryption key
encryption-key
Specifies the value of the encryption key:
•
•
transmit-key
Specifies the key for encrypting transmit data from the access point. Key slot 1 is the default key slot.
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Usage Guidelines
Using security features such as authenticated key management can limit WEP key configurations. Table 2-4 lists WEP key restrictions based on your security configuration.
Examples
This example shows how to configure a 40-bit encryption key with a value of 11aa33bb55 as
WEP key 1 used on VLAN number 1:AP(config-if)# encryption vlan 1 key 1 size 40bit 11aa33bb55 transmit-keyThis example shows how to remove WEP key 1 on VLAN 1:
AP(config-if)# no encryption vlan 1 key 1Related Commands
encryption mode cipher
Use the encryption mode cipher configuration interface command to enable a cipher suite. Cipher suites are sets of encryption algorithms that, like WEP, protect radio communication on your wireless LAN. You must use a cipher suite to enable Wi-Fi Protected Access (WPA) or Cisco Centralized Key Management (CCKM).
Because cipher suites provide the protection of WEP while also allowing use of authenticated key management, we recommend that you enable WEP by using the encryption mode cipher command in the CLI or by using the cipher drop-down menu in the web-browser interface. Cipher suites that contain TKIP provide the best security for your wireless LAN, and cipher suites that contain only WEP are the least secure.
Note
encryption [ vlan vlan ] mode cipher
{ [ ckip | cmic | ckip-cmic | tkip ] }
{ [ wep128 | wep40 ] }Syntax Description
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Usage Guidelines
If you configure your access point to use WPA or CCKM authenticated key management, you must select a cipher suite compatible with the authenticated key management type. Table 2-5 lists the cipher suites that are compatible with WPA and CCKM.
Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for a complete description of WPA and CCKM and instructions for configuring authenticated key management.
Examples
This example sets up a cipher suite for VLAN 22 that enables CKIP, CMIC, and 128-bit WEP.
ap(config-if)# encryption vlan 22 mode cipher ckip-cmic wep128Related Commands
Configures the access point for WEP encryption
Configures the client authentication type for an SSID, including WPA and CCKM authenticated key management
encryption mode wep
Use the encryption mode wep configuration interface command to enable a specific encryption type that is used to communicate on the wireless LAN or on a specific VLAN. When encryption is enabled, all client devices on the wireless LAN or on a VLAN must support the specified encryption methods to communicate with the access point. Use the no form of the command to disable the encryption features on a specific VLAN.
Note
[no] encryption [vlan vlan-id ] mode wep
{mandatory | optional}
{key-hash | mic [key-hash] }Syntax Description
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Examples
This example shows how to specify that encryption key hashing must be used on VLAN number 1:
AP(config-if)# encryption vlan 1 mode wep mandatory key-hashThis example shows how to disable mandatory encryption on VLAN 1:
AP(config-if)# no encryption vlan 1 mode wep mandatoryRelated Commands
fragment-threshold
Use the fragment-threshold configuration interface command to set the size at which packets are fragmented. Use the no form of the command to reset the parameter to defaults.
[no] fragment-threshold 256-2346
Syntax Description
Defaults
The default threshold is 2346 bytes
Command Modes
Configuration interface
Command History
Examples
This example shows how to set the packet fragment threshold size to 1800 bytes:
AP(config-if)# fragment-threshold 1800This example shows how to reset the packet fragment threshold size to defaults:
AP(config-if)# no fragment-thresholdRelated Commands
group (local server configuration mode)
Use the group local server configuration mode command to enter user group configuration mode and configure a user group to which you can assign shared settings. In user group configuration mode you can specify settings for the user group such as VLAN and SSID.
group group
Note
Syntax Description
Defaults
This command has no defaults.
Command Modes
Local server configuration mode
Command History
Examples
This example shows how to create a user group on the local authenticator:
AP(config-radsrv)# group hoosiersRelated Commands
guest-mode (SSID configuration mode)
Use the guest-mode SSID configuration mode command to configure the radio interface (for the specified SSID) to support guest mode. Use the no form of the command to disable the guest mode.
[no] guest-mode
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
The access point can have one guest-mode SSID or none at all. The guest-mode SSID is used in beacon frames and response frames to probe requests that specify the empty or wildcard SSID. If no guest-mode SSID exists, the beacon contains no SSID and probe requests with the wildcard SSID are ignored. Disabling the guest mode makes the networks slightly more secure. Enabling the guest mode helps clients that passively scan (do not transmit) associate with the access point. It also allows clients configured without a SSID to associate.
Examples
This example shows how to set the wireless LAN for the specified SSID into guest mode:
AP(config-if-ssid)# guest-modeThis example shows how to reset the guest-mode parameter to default values:
AP(config-if-ssid)# no guest-modeRelated Commands
Specifies the SSID and enters the SSID configuration mode
show running-config
Displays the current access point operating configuration
iapp standby mac-address
Use the iapp standby mac-address global configuration command to configure an access point to be in standby mode and specify the active access point's MAC address. Use the no form of this command to disable the access point standby mode.
[no] iapp standby mac-address mac-address
Note
Syntax Description
Defaults
This command has no default setting.
Command Modes
Global configuration
Command History
Examples
This example shows how to place the access point in standby mode and indicate the MAC address of the active access point:
AP(config)# iapp standby mac-address 0040.9631.81cfThis example shows how to stop or disable the standby mode:
AP(config)# no iapp standby mac-address 0040.9631.81cf
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
Configures the polling interval in standby mode
Configures the polling timeout value in standby mode
iapp standby poll-frequency
Use the iapp standby poll-frequency global configuration command to configure the standby mode polling interval. Use the no form of this command to clear the access point standby mode poll frequency.
[no] iapp standby poll-frequency sec [mac-address]
Note
Syntax Description
sec
Specifies the standby mode poll frequency in seconds
mac-address
Specifies the MAC address of an access point
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Examples
This example shows how to specify the standby mode poll frequency of 5 minutes:
AP(config)# iapp standby poll-frequency 300This example shows how to stop or disable the standby mode:
AP(config)# no iapp standby mac-address 0040.9631.81cf
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
Places the access point into standby mode and identifies the MAC address of the active access point
Specifies the access point standby mode polling timeout value
iapp standby timeout
Use the iapp standby timeout global configuration command to configure the standby mode polling timeout value. Use the no form of this command to clear the standby mode polling timeout value.
[no] iapp standby timeout sec
Syntax Description
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Examples
This example shows how to specify the standby mode polling timeout of 1 minute:
AP(config)# iapp standby timeout 60This example shows how to clear the standby mode timeout value:
AP(config)# no iapp standby timeout
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
Places the access point into standby mode and identifies the MAC address of the active access point
Specifies the standby mode polling interval
infrastructure-client
Use the infrastructure-client configuration interface command to configure a virtual interface for a workgroup bridge client. Use the no form of the command to disable the workgroup bridge client virtual interface.
[no] infrastructure-client
Syntax Description
This command has no arguments or keywords.
Defaults
The default is infrastructure client disabled.
Command Modes
Configuration interface
Command History
Usage Guidelines
Enable the infrastructure client feature to increase the reliability of multicast messages to workgroup bridges. When enabled, the access point sends directed packets containing the multicasts, which are retried if necessary, to the associated workgroup bridge. Enable only when necessary because it can greatly increase the load on the radio cell.
Examples
This example shows how to configure a virtual interface for a workgroup bridge client.
AP(config-if)# infrastructure-clientThis example shows how to specify that a workgroup bridge client virtual interface is not supported.
AP(config-if)# no infrastructure-clientRelated Commands
show running-config
Displays information on the current running access point configuration
infrastructure-ssid (SSID configuration mode)
Use the infrastructure-ssid command in SSID configuration mode to reserve this SSID for infrastructure associations, such as those from one access point or bridge to another. Use the no form of the command to revert to a normal non-infrastructure SSID.
[ no ] infrastructure-ssid [ optional ]
Syntax Description
optional
Specifies that both infrastructure and mobile client devices are allowed to associate using the SSID
Defaults
This command has no defaults.
Command Modes
SSID configuration interface
Command History
Usage Guidelines
This command controls the SSID that access points and bridges use when associating with one another. A root access point only allows a repeater access point to associate using the infrastructure SSID, and a root bridge only allows a non-root bridge to associate using the infrastructure SSID. Repeater access points and non-root bridges use this SSID to associate with root devices. Configure authentication types and VLANs for an SSID to control the security of access points and bridges.
Examples
This example shows how to reserve the specified SSID for infrastructure associations on the wireless LAN:
AP(config-if-ssid)# infrastructure-ssidThis example shows how to restore the SSID to non-infrastructure associations:
AP(config-if-ssid)# no infrastructure-ssidRelated Commands
interface dot11radio
Use the interface dot11radio global configuration command to place access point into the radio configuration mode.
interface dot11radio interface-number
Syntax Description
interface-number
Specifies the radio interface number (The 2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.)
Defaults
The default radio interface number is 0.
Command Modes
Global configuration
Command History
Examples
This example shows how to place the access point into the radio configuration mode:
AP# interface dot11radio 0Related Commands
ip proxy-mobile
Use the ip proxy-mobile configuration interface command to enable the access point to participate in proxy Mobile IP operations. Use the no form of this command to disable proxy Mobile IP operations on the access point.
[no] ip proxy-mobile
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Examples
This example shows how to enable the proxy Mobile IP interface on the access point.
AP(config-if)# ip proxy-mobileThis example shows how to disable proxy Mobile IP operations on the access point.
AP(config-if)# no ip proxy-mobileRelated Commands
ip proxy-mobile (SSID configuration mode)
Use the ip proxy-mobile SSID configuration mode command to configure the radio interface (for the specified SSID) to support proxy Mobile IP. Use the no form of the command to reset the parameter to the default value.
[no] ip proxy-mobile
Syntax Description
This command has no arguments or keywords.
Defaults
No proxy Mobile IP support is the default setting.
Command Modes
SSID configuration interface
Command History
Examples
This example shows how to enable proxy Mobile IP support on the wireless LAN for the specified SSID:
AP(config-if-ssid)# ip proxy-mobileThis example shows how to disable proxy Mobile IP support:
AP(config-if-ssid)# no ip proxy-mobileRelated Commands
ip proxy-mobile aap
Use the ip proxy-mobile aap global configuration command to specify the IP addresses for the primary and secondary AAPs. Use the no form of this command to clear the primary AAP and secondary AAP addresses.
[no] ip proxy-mobile aap address
[ address2 address3]Syntax Description
address
Specifies the primary AAP IP address
address2
(Optional) Specifies the secondary AAP IP address
address3
(Optional) Specifies a second secondary AAP IP address
Defaults
AAP address information is not defined by default.
Command Modes
Global configuration
Command History
Examples
This example shows how to specify the IP addresses for proxy Mobile IP primary and secondary AAPs:
AP(config)# ip proxy-mobile aap 10.10.9.21 10.10.9.22 10.10.9.23This example shows how to clear out the IP addresses for the proxy Mobile IP AAPs:
AP(config)# no ip proxy-mobile aap
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
Enables and disables proxy Mobile IP and removes the configuration information when disabled
Displays proxy Mobile IP information
ip proxy-mobile enable
Use the ip proxy-mobile enable global configuration command to enable or disable proxy Mobile IP. Use the no form of this command to disable proxy Mobile IP and remove all associated CLIs.
[no] ip proxy-mobile enable
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled by default.
Command Modes
Global configuration
Command History
Examples
This example shows how to enable proxy Mobile IP:
AP(config)# ip proxy-mobile enableThis example shows how to disable proxy Mobile IP and remove all associated CLIs:
AP(config)# no ip proxy-mobile enable
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
ip proxy-mobile pause
Use the ip proxy-mobile pause global configuration command to enable or disable proxy Mobile IP without removing all associated CLIs. Use the no form of this command to re-enable proxy Mobile IP.
[no] ip proxy-mobile pause
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Examples
This example shows how to disable proxy Mobile IP without removing the configuration:
AP(config)# ip proxy-mobile pauseThis example shows how to re-enable proxy Mobile IP:
AP(config)# no ip proxy-mobile pause
Related CommandsYou can verify your settings by entering the show class-map privileged EXEC command.
ip proxy-mobile secure
Use the ip proxy-mobile secure global configuration command to specify the proxy Mobile IP security association information for a range of IP addresses. Use the no form of this command to reset the parameters to default values.
[no] ip proxy-mobile secure
node address-start address-end
spi spi
key {hex | ascii} stringSyntax Description
Defaults
The default key setting is ASCII.
Command Modes
Global configuration
Command History
Examples
This example shows how to configure proxy Mobile IP security association information for an IP address range of 10.9.1.20 to 10.9.1.60 with an ASCII key of 123456789abcd:
AP(config)# ip proxy-mobile secure 10.9.1.20 10.9.1.60 spi 100 key ascii 123456789abcdThis example shows how to reset the proxy Mobile IP security association information to defaults:
AP(config)# no ip proxy-mobile secure
Related Commands
Enables and disables proxy Mobile IP and removes the configuration information when disabled
Displays proxy Mobile IP information
l2-filter bridge-group-acl
Use the l2-filter bridge-group-acl configuration interface command to apply a Layer 2 ACL filter to the bridge group incoming and outgoing packets between the access point and the host (upper layer). Use the no form of the command to disable the Layer 2 ACL filter
[no] l2-filter bridge-group-acl
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Configuration interface
Command History
Examples
This example shows how to apply a Layer 2 ACL filter to the bridge group packets:
AP(config-if)# l2-filter bridge-group-aclThis example shows how to activate a Layer 2 ACL filter:AP(config-if)# no l2-filter bridge-group-aclRelated Commands
led flash
Use the led flash privileged EXEC command to start or stop the blinking of the LED indicators on the access point for a specified number of seconds. Without arguments, this command blinks the LEDs continuously.
led flash [seconds | disable]
Syntax Description
seconds
Specifies the number of seconds (1 to 3600) that the LEDs blink
disable
Stops the blinking of the LEDs
Defaults
The default is continuous blinking of the LEDs.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to blink the access point LEDs for 30 seconds:
AP# led flash 30This example shows how to stop the blinking of the access point LEDs:AP# led flash disableRelated Commands
logging buffered
Use the logging buffered global configuration command to begin logging of messages to an internal buffer. Use the no form of this command to stop logging messages.
[no] logging buffered [size] [severity]
Syntax Description
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Examples
This example shows how to begin logging severity 3 messages to an internal 5000-byte buffer:
AP(config)# logging buffered 5000 3This example shows how to stop the message logging:
AP(config)# no logging buffered
Related Commands
show logging
Displays recent logging event headers or complete events
clear logging
Clears logging status count and the trace buffer
match (class-map configuration)
Use the match class-map configuration command to define the match criteria to classify traffic. Use the no form of this command to remove the match criteria.
[no] match {access-group acl-index-or-name |
ip [dscp dscp-list | precedence precedence-list] |
vlan vlan-id}Syntax Description
Note
Defaults
This command has no defaults.
Command Modes
Class-map configuration
Command History
Usage Guidelines
Use the class-map global configuration command to enter the class-map configuration mode. The match command in the class-map configuration mode is used to specify which fields in the incoming packets are examined to classify the packets. Only the IP access group or the MAC access group matching to the Ether Type/Len are supported.
You can use the match ip dscp dscp-list command only in a policy map that is attached to an egress interface.
Only one match command per class map is supported.
For the match ip dscp dscp-list or the match ip precedence ip-precedence-list command, you can enter a mnemonic name for a commonly used value. For example, you can enter the match ip dscp af11 command, which is the same as entering the match ip dscp 10 command. You can enter the match ip precedence critical command, which is the same as entering the match ip precedence 5 command. For a list of supported mnemonics, enter the match ip dscp ? or the match ip precedence ? command to see the command-line help strings.
Examples
This example shows how to create a class map called class2, which matches all the incoming traffic with DSCP values of 10, 11, and 12:
AP(config)# class-map class2AP(config-cmap)# match ip dscp 10 11 12AP(config-cmap)# exitThis example shows how to create a class map called class3, which matches all the incoming traffic with IP-precedence values of 5, 6, and 7:
AP(config)# class-map class3AP(config-cmap)# match ip precedence 5 6 7AP(config-cmap)# exitThis example shows how to delete the IP-precedence match criteria and to classify traffic by vlan:
AP(config)# class-map class2AP(config-cmap)# match ip precedence 5 6 7AP(config-cmap)# no match ip precedenceAP(config-cmap)# match vlan 2AP(config-cmap)# exitYou can verify your settings by entering the show class-map privileged EXEC command.
Related Commands
Creates a class map to be used for matching packets to the class whose name you specify
show class-map
Displays quality of service (QoS) class maps
max-associations (SSID configuration mode)
Use the max-associations SSID configuration mode command to configure the maximun number of associations supported by the radio interface (for the specified SSID). Use the no form of the command to reset the parameter to the default value.
[no] max-associations value
Syntax Description
Defaults
This default maximum is 255.
Command Modes
SSID configuration interface
Command History
Examples
This example shows how to set the maximum number of associations to 5 on the wireless LAN for the specified SSID:
AP(config-if-ssid)# max-associations 5This example shows how to reset the maximum number of associations to the default value:
AP(config-if-ssid)# no max-associationsRelated Commands
nas (local server configuration mode)
Use the nas local server configuration mode command to add an access point to the list of devices that use the local authenticator.
nas ip-address key shared-key
Syntax Description
Defaults
This command has no defaults.
Command Modes
Local server configuration mode
Command History
Examples
This example shows how to add an access point to the list of NAS access points on the local authenticator:
AP(config-radsrv)# nas 10.91.6.158 key 110337Related Commands
packet retries
Use the packet retries configuration interface command to specify the maximum number of attempts to send a packet. Use the no form of the command to reset the parameter to defaults.
[no] packet retries 1-128
Syntax Description
Defaults
The default number of retries is 32.
Command Modes
Configuration interface
Command History
Examples
This example shows how to specify 15 as the maximum number of retries.
AP(config-if)# packet retries 15This example shows how reset the packet retries to defaults.
AP(config-if)# no packet retriesRelated Commands
parent
Use the parent configuration interface command to add a parent to a list of valid parent access points. Use the no form of the command to remove a parent from the list.
[no] parent 1-4 mac-address
Syntax Description
1-4
Specifies the parent root access point number (1 to 4)
mac-address
Specifies the MAC address (in xxxx.xxxx.xxxx format) of a parent access point
Defaults
Repeater access point operation is disabled by default.
Command Modes
Configuration interface
Command History
Usage Guidelines
The parent command adds a parent to the list of valid parent access points. Use this command multiple times to define up to four valid parents. A repeater access point operates best when configured to associate with specific root access points that are connected to the wired LAN.
Examples
This example shows how to set up repeater operation with the parent 1 access point:
AP(config-if)# parent 1 0040.9631.81cfThis example shows how to set up repeater operation with the parent 2 access point:
AP(config-if)# parent 2 0040.9631.81daThis example shows how to remove a parent from the parent list:
AP(config-if)# no parentRelated Commands
parent timeout
Use the parent timeout configuration interface command to define the amount of time to associate with a parent access point. Use the no form of the command to disable the timeout.
[no] parent timeout sec
Syntax Description
sec
Specifies the amount of time the access point attempts to associate with the specified parent access point (0 to 65535 seconds)
Defaults
Parent timeout is disabled by default.
Command Modes
Configuration interface
Command History
Usage Guidelines
The parent timeout defines how long the access point attempts to associate with a parent in the parent list. After the timeout, another acceptable parent is used. You set up the parent list using the parent command. With the timeout disabled, the parent must come from the parent list.
Examples
This example shows how to set up repeater operation with the parent 1 access point with a timeout of 60 seconds:
AP(config-if)# parent timeout 60This example shows how to disable repeater operation:
AP(config-if)# no parentRelated Commands
payload-encapsulation
Use the payload-encapsulation configuration interface command to specify the Ethernet encapsulation type used to format Ethernet data packets that are not formatted using IEEE 802.3 headers. Data packets that are not IEEE 802.3 packets must be reformatted using IEEE 802.1H or RFC1042. Use the no form of the command to reset the parameter to defaults.
[no] payload-encapsulation
{snap | dot1h}Syntax Description
snap
(Optional) Specifies the RFC1042 encapsulation
dot1h
(Optional) Specifies the IEEE 802.1H encapsulation
Defaults
The default payload encapsulation is snap.
Command Modes
Configuration interface
Command History
Examples
This example shows how to specify the use of IEEE 802.1H encapsulation:
AP(config-if)# payload-encapsulation dot1hThis example shows how to reset the parameter to defaults:
AP(config-if)# no payload-encapsulationRelated Commands
power client
Use the power client configuration interface command to configure the maximum power level clients should use for IEEE 802.11b radio transmissions to the access point. The power setting is transmitted to the client device during association with the access point. Use the no form of the command to not specify a power level.
2.4-GHz Radio (dot11radio0)
[no] power client
{1 | 5 | 20 | 30 | 50 | 100} | maximum5-GHz Radio (dot11radio1)
[no] power client
{5 | 10 | 20 | 40} | maximum
Note
Syntax Description
For the 2.4-GHz radio:
1, 5, 20, 30, 50, 100, maximumFor the 5-GHz radio:
5, 10, 20, 40, maximumSpecifies a specific power level in mW. Maximum power is regulated by the regulatory agency in the country of operation and is set during manufacture of the access point and client device.
For a list of maximum power levels allowed in each regulatory domain for the 2.4-GHz radio, see Table 2-6. For a list of maximum power levels allowed in each regulatory domain for the 5-GHz radio, see Table 2-7.
Defaults
The default is no power level specification during association with the client.
Command Modes
Configuration interface
Command History
Usage Guidelines
Use this command to specify the desired transmitter power level for clients. Lower power levels reduce the radio cell size and interference between cells. The client software chooses the actual transmit power level, choosing between the lower of the access point value and the locally configured value. The maximum transmit power is limited according to regulatory region.
Examples
This example shows how to specify a 20-mW power level for client devices associated to the access point radio:
AP(config-if)# power client 20This example shows how to disable power level requests:
AP(config-if)# no power clientRelated Commands
power local
Use the power local configuration interface command to configure the access point radio power level. Use the no form of the command to reset the parameter to defaults.
2.4-GHz Access Point Radio
[no] power local {1 | 5 | 20 | 30 | 50 | 100 | maximum}
5-GHz Access Point Radio
[no] power local {5 | 10 | 20 | 40 | maximum}
5.8-GHz Bridge Radio
[no] power local {12 | 15 | 18 | 21 | 22 | 23 | 24 | maximum}
Syntax Description
For the 2.4-GHz access point radio:
1, 5, 20, 30, 50, 100, or maximumFor the 5-GHz access point radio:
5, 10, 20, 40, or maximumFor the 5.8-GHz bridge radio:
12, 15, 18, 21, 22, 23, 24, or maximumSpecifies access point power setting in mW. Maximum power is regulated by the regulatory agency in the country of operation and is set during manufacture of the access point. For a list of maximum power levels allowed in each regulatory domain for the 2.4-GHz access point radio, see Table 2-6. For a list of maximum power levels allowed in each regulatory domain for the 5-GHz access point radio, see Table 2-7.
Specifies bridge power setting in dBm. Maximum power is regulated by the regulatory agency in the country of operation and is set during manufacture of the bridge. For a list of maximum power levels allowed in each regulatory domain for the 5.8-GHz bridge radio, see Table 2-8.
Table 2-8 Maximum Power Levels and Antenna Gains
Omnidirectional
Antenna
Antenna
Antenna
Dish
AntennaAmericas (-A)
P2P1
24 dBm
24 dBm
24 dBm
22 dBm
P2MP2
24 dBm
24 dBm
na
1 Point to point.
2 Point to multipoint.
3 A maximum of 13 dBm is allowed, but that setting is not supported by the bridge.
4 On point-to-multipoint links, the remote bridges communicating with the central bridge are allowed to use a maximum power setting of 24 dBm. The central bridge is limited to a maximum power setting of 12 dBm.
Defaults
The default local power level is maximum.
Command Modes
Configuration interface
Command History
Usage Guidelines
Use this command to specify the local transmit power level. Lower power levels reduce the radio cell size and interference between cells. The maximum transmit power is limited by region.
Examples
This example shows how to specify a 20-mW transmit power level for one of the the access point radios:
AP(config-if)# power local 20This example shows how to reset power to defaults on one of the access point radios:
AP(config-if)# no power localRelated Commands
preamble-short
Use the preamble-short configuration interface command to enable short radio preambles. The radio preamble is a selection of data at the head of a packet that contains information that the access point and client devices need when sending and receiving packets. Use the no form of the command to change back to default values.
[no] preamble-short
Note
Syntax Description
This command has no arguments or keywords.
Defaults
The default is short radio preamble.
Command Modes
Configuration interface
Command History
Usage Guidelines
If short radio preambles are enabled, clients may request either short or long preambles and the access point formats packets accordingly. Otherwise, clients are told to use long preambles.
Examples
This example shows how to set the radio packet to use a short preamble.
AP(config-if)# preamble-shortThis example shows how to set the radio packet to use a long preamble.
AP(config-if)# no preamble-shortRelated Commands
radius-server local
Use the radius-server local global configuration command to enable the access point as a local or backup authenticator and to enter configuration mode for the local authenticator.
radius-server local
Note
Defaults
This command has no defaults.
Command Modes
Global configuration
Command History
Examples
This example shows how to enable the access point as a local or backup authenticator:
AP(config)# radius-server localRelated Commands
rts
Use the rts configuration interface command to set the Request-To-Send (RTS) threshold and the number of retries. Use the no form of the command to reset the parameter to defaults.
Access Points
[no] rts
{threshold 0-2347 | retries 1-128}Bridges
[no] rts
{threshold 0-4000 | retries 1-128}Syntax Description
Defaults
The default threshold is 2330 bytes on access points and 4000 bytes on bridges.
The default number of retries is 32.
Command Modes
Configuration interface
Command History
12.2(4)JA
This command was introduced.
12.2(11)JA
This command was modified to support bridges.
Usage Guidelines
On bridges set up in a point-to-point configuration, set the RTS threshold to 4000 on both the root and non-root bridges. If you have multiple bridges set up in a point-to-multipoint configuration, set the RTS threshold to 4000 on the root bridge and to 0 on the non-root bridges.
Examples
This example shows how to set the RTS threshold on a bridge to 4000 bytes:
bridge(config-if)# rts threshold 4000This example shows how to set the RTS retries count to 3:
AP(config-if)# rts retries 3This example shows how to reset the parameter to defaults:
AP(config-if)# no rtsshow controllers dot11radio
Use the show controllers dot11radio privileged EXEC command to display the radio controller status.
show controllers dot11radio interface-number
Syntax Description
interface-number
Specifies the radio interface number. The 2.4-GHz radio is radio 0. The 5-GHz radio is radio 1.
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the radio controller status for radio interface 0:
AP# show controllers dot11radio 0Related Commands
show dot11 adjacent-ap
Use the show dot11 adjacent-ap privileged EXEC command to display the fast, secure roaming list of access points that are adjacent to this access point. The WDS access point builds the adjacent access point list based on data from client devices that support fast, secure roaming. This command works only when you configure your wireless LAN for fast, secure roaming and there are client devices on your wireless LAN that support fast, secure roaming.
show dot11 adjacent-ap
Note
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the adjacent access point list:
AP# show dot11 adjacent-apThis example shows a list of adjacent access points:
Radio Address Channel Age(Hours) SSID-------- ----------------------- ------------ ---------------- ----------0 0007.50d5.8759 1 1 tsunamiThese are descriptions of the list columns:
•
•
•
•
•
Related Commands
Specifies the number of hours an inactive entry remains in the adjacent access point list
show dot11 associations
Use the show dot11 associations privileged EXEC command to display the radio association table, radio association statistics, or to selectively display association information about all repeaters, all clients, a specific client, or basic service clients.
show dot11 associations
[client | repeater | statistics | H.H.H | bss-only | all-client]Syntax Description
Defaults
When parameters are not specified, this command displays the complete radio association table.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the radio association table:
AP# show dot11 associationsThis example shows how to display all client devices associated with the access point:
AP# show dot11 associations clientThis example shows how to display access point radio statistics:
AP# show dot11 associations statisticsRelated Commands
show dot11 carrier busy
Use the show dot11 carrier busy privileged EXEC command to display recent carrier busy test results. You can display test results once using this command. After the display, you must use the dot11 carrier busy command to run the carrier busy test again.
show dot11 carrier busy
Syntax Description
This command has no arguments or keywords.
DefaultsDefaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the carrier busy test results:
AP# show dot11 carrier busyThis example shows the carrier busy test results:
Frequency Carrier Busy %--------- --------------5180 05200 25220 275240 55260 15280 05300 35320 2Related Commands
show dot11 network-map
Use the show dot11 network-map privileged EXEC command to display the radio network map. The radio network map contains information from Cisco access points in the same Layer 2 domain as this access point.
show dot11network-map
Syntax Description
This command has no arguments or keywords.
DefaultsDefaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
This command displays network map information only if you first enable the network map feature with the dot11 network map command.
Examples
This example shows how to display the radio network map:
AP# show dot11 network-mapRelated Commands
show dot11 statistics client-traffic
Use the show dot 11 statistics client-traffic privileged EXEC command to display the radio client traffic statistics.
show dot11 statistics client-traffic
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the radio client traffic statistics:
AP# show dot11 statistics client-trafficRelated Commands
Deauthenticates a client with a specified MAC address
Resets the statistics for a specified radio interface or client device
show environment
Use the show environment EXEC command to display information about the temperature of the bridge radio.
show environment
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
EXEC
Command History
Examples
This example shows how to display temperature information for the bridge radio:
bridge# show environmentEnvironmental StatisticsEnvironmental status as of 00:10:45 UTC Thu Mar 27 2003Data is 3 second(s) old, refresh in 57 second(s)Dot11Radio0 temperature measured at 37(C)Related Commands
show iapp rogue-ap-list
Use the show iapp rogue-ap-list privileged EXEC command to display a list of rogue access points.
show iapp rogue-ap-list
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The list contains an entry for each access point that a client station reported as a possible rogue access point. Each list entry contains the following information:
Rogue AP—MAC address of the reported rogue access point
Count—The number of times the access point was reported
Last Rpt Src—The MAC address of the last client to report the rogue access point
R—The last reason code
Prev Rpt Src—The MAC address of any previous client that reported the rogue access point
R—The previous reason code
Last(Min)—The number of minutes since the last report
1st(Min)—The number of minutes since the access point was first reported as a possible rogue
Name—The name of a Cisco rogue access point
The following reason codes are displayed:
1—The rogue was not running 802.1x
2—Authentication with the rogue timed out
3—Bad user password
4—Authentication challenge failed
Examples
This example shows how to display the list of IAPP rogue access points:
AP# show iapp rogue-ap-listRelated Commands
show iapp standby-parms
Use the show iapp standby-parms privileged EXEC command to display IAPP standby parameters when a standby MAC address is configured. The information displayed includes the standby MAC address, the time-out value, and the poll-frequency value.
show iapp standby-parms
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Privileged EXEC
Command History
Examples
This example shows how to display the IAPP standby parameters:
AP# show iapp standby-parmsRelated Commands
