Table Of Contents

G

gateway address (ccn subsystem sip)

gateway port (ccn subsystem sip)

groupname

G

---

gateway address (ccn subsystem sip)

gateway port (ccn subsystem sip)

groupname

gateway address (ccn subsystem sip)

To configure the IP address of the SIP proxy server, use the gateway address command in Cisco Unity Express SIP configuration mode. To remove the address, use the no form of this command.

gateway address ip-address

no gateway address

Syntax Description

ip-address

IP address of the SIP proxy server. The default value is 0.0.0.0.

Defaults

IP address 0.0.0.0

Command Modes

Cisco Unity Express SIP configuration

Command History

Cisco Unity Express Release	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco CallManager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco CallManager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example configures a SIP proxy server address of 10.2.34.1:

se-10-0-0-0> enable

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn subsystem sip

se-10-0-0-0(config-sip)# gateway address 10.2.34.1

se-10-0-0-0(config-sip)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
show ccn subsystem sip	Displays details for the SIP subsystem.

gateway port (ccn subsystem sip)

To configure the UDP or TCP port on the SIP proxy server, use the gateway port command in Cisco Unity Express SIP configuration mode. To remove the port, use the no form of this command.

gateway port port-number

no gateway port

Syntax Description

port-number

UDP or TCP port on the SIP proxy server. The default value is 5060.

Defaults

Port 5060

Command Modes

Cisco Unity Express SIP configuration

Command History

Cisco Unity Express Release	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco CallManager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco CallManager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example configures the SIP proxy server port to 23:

se-10-0-0-0> enable

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn subsystem sip

se-10-0-0-0(config-sip)# gateway port 23

se-10-0-0-0(config-sip)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
show ccn subsystem sip	Displays details for the SIP subsystem.

groupname

To configure a Cisco Unity Express group, use the groupname command in either Cisco Unity Express EXEC mode or configuration mode.

EXEC Mode

groupname name [create | delete | description "description" | fullname display "full-name"]

Configuration Mode

groupname name [create | member username | owner ownername | phonenumber phone-number | phonenumberE164 full-number | privilege privilege-name]

Syntax Description

name	The name of the group.
create	(Optional) Creates a group with no other information.
delete	(Optional) Deletes the group.
description "description"	(Optional) Specifies a description of the group. The description must be enclosed in double quotes ("").
fullname display "full-name"	(Optional) Specifies a long name of the group as it should appear on other telephone displays. The name must be entered in double quotes ("").
member username	(Optional) Associates an existing user as a member of this group. If the username value does not exist, this command will create it with no other information.
owner ownername	(Optional) Specifies the user who owns this group.
phonenumber phone-number	(Optional) Associates an extension or number with this group.
phonenumberE164 full-number	(Optional) Associates a full telephone number and area code with this group.
privilege privilege-name	(Optional) Assigns a privilege to the group.

Command Modes

Cisco Unity Express EXEC
Cisco Unity Express configuration

Command History

Cisco Unity Express Release	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco CallManager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco CallManager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.
2.1	Additional privileges were made available: broadcast, ViewPrivateList, and ManagePublicList.

Usage Guidelines

The EXEC version of the command stores the permitted information in Cisco Unity Express flash memory. If a problem with the disk occurs, this information is available so that the group members may access the group's voice mailbox.

The configuration version of the command is stored in the Cisco Unity Express system configuration file. If a power outage or a system shutdown occurs, the group information can be retrieved.

Several privileges are available:

•Superuser—An administrator, also called a superuser, has the capability, or privilege, of accessing all the configuration and maintenance functions, including the Administration via Telephone (AvT).

•ManagePrompts—The prompt management user has access to the AvT but not to any other administrative functions.

•Broadcast—The broadcast privilege permits the user to send broadcast messages across the network.

•ManagePublicList—The ManagePublicList privilege permits the user to create and modify public distribution lists.

•ViewPrivateList—The ViewPrivateList privilege allows the user to view another user's private distribution lists. The ViewPrivateList user can not modify or delete the private lists.

These privilege levels are assigned to a group, and any member of the group is granted the privilege rights. The software initialization process created an Administrator group from the imported users designated as administrators. Other groups can be created with these privileges. Assign users to an existing group using the CLI commands or the GUI option Configuration > Users.

To display the current list of privileges, use the show privileges command in Cisco Unity Express EXEC mode. Use the show groups privileges command to display the privileges assigned to each group.

Examples

The following example creates the group Sales with two members, one owner, and two privileges:

se-10-0-0-0> enable

se-10-0-0-0# groupname sales fullname display "Sales New York"

se-10-0-0-0# groupname sales description "Sales group in New York branch"

se-10-0-0-0# config t

se-10-0-0-0(config)# groupname sales phonenumber 50120

se-10-0-0-0(config)# groupname sales phonenumberE164 12225550120

se-10-0-0-0(config)# groupname sales member user4

se-10-0-0-0(config)# groupname sales member user5

se-10-0-0-0(config)# groupname sales owner user6

se-10-0-0-0(config)# groupname sales privilege broadcast

se-10-0-0-0(config)# groupname sales privilege ManagePublicList

se-10-0-0-0(config)# exit

Related Commands

Command	Description
show group detail groupname	Displays the configuration details for a specific group.
show groups	Displays a list of configured group names.
show privileges	Displays a list of available privileges.
show users	Displays a list of configured usernames.
username	Configures a Cisco Unity Express user.