Table Of Contents

A

abbreviation (network location id)

application (ccn trigger jtapi)

application (ccn trigger sip)

A

---

abbreviation (network location id)

application (ccn trigger jtapi)

application (ccn trigger sip)

abbreviation (network location id)

To create an alphanumeric abbreviation for a Cisco Unity Express network location, use the abbreviation command in Cisco Unity Express location configuration mode. To delete an abbreviation, use the no form of this command.

abbreviation name

no abbreviation name

Syntax Description

name	Alphanumeric abbreviation for the location that is spoken to a user when the user performs addressing functions in the telephone user interface.

Defaults

The default abbreviation is an empty string.

Command Modes

Cisco Unity Express location configuration

Command History

Release	Modification
2.0	This command was introduced.

Usage Guidelines

You cannot enter more than 5 characters.

Examples

The following example shows an abbreviation for a Birmingham remote voice-mail location:

se-10-0-0-0# config t

se-10-0-0-0(config)# network location id 1

se-10-0-0-0(config-location)# abbreviation bham

se-10-0-0-0(config-location)# end
se-10-0-0-0(config)#

Related Commands

Command	Description
show network locations	Displays the name and abbreviation of the network locations.

application (ccn trigger jtapi)

To specify the name of the application to start when a trigger is entered, use the application command in Cisco Unity Express configuration trigger mode.

application name

Syntax Description

name	Specifies the name of the application to start when the trigger is entered.

Command Modes

CCN configuration trigger mode

Command History

Cisco Unity Express Release	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco CallManager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco CallManager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Usage Guidelines

Use the application command to specify the name of the application to start when the trigger is entered.

Examples

The following example specifies that the myapp application will start when the 1234 trigger is entered.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger jtapi 1234

se-10-0-0-0(config-trigger)# application myapp

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
ccn trigger jtapi phonenumber	Enters CCN trigger configuration mode.
show ccn trigger	Displays the CCN trigger details.

application (ccn trigger sip)

To specify the name of the application to start when a trigger is entered, use the application command in Cisco Unity Express configuration trigger mode.

application name

Syntax Description

name	Specifies the name of the application to start when the trigger is entered.

Command Modes

CCN configuration trigger mode

Command History

Cisco Unity Express Release	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco CallManager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco CallManager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Usage Guidelines

Use the application command to specify the name of the application to start when the trigger is entered.

Examples

The following example specifies that the myapp application will start when the 1234 trigger is entered.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger sip 1234

se-10-0-0-0(config-trigger)# application myapp

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
ccn trigger sip phonenumber	Enters CCN trigger configuration mode.
show ccn trigger	Displays the CCN trigger details.