Table Of Contents
Setting Up an NEC NEAX 2400 Digital PIMG Integration with Cisco Unity
Task List to Create the Integration with the NEC NEAX 2400 PIMG Phone System
Requirements
Programming the NEC NEAX 2400 PIMG Phone System for Integrating with Cisco Unity
Setting Up the Digital PIMG Units
Creating an Integration with the NEC NEAX 2400 Phone System
Setting Up an NEC NEAX 2400 Digital PIMG Integration with Cisco Unity
For detailed instructions for setting up an NEC NEAX 2400 digital PIMG integration with Cisco Unity, see the following sections in this chapter:
•
Task List to Create the Integration with the NEC NEAX 2400 PIMG Phone System
•Requirements
•Programming the NEC NEAX 2400 PIMG Phone System for Integrating with Cisco Unity
•Setting Up the Digital PIMG Units
•Creating an Integration with the NEC NEAX 2400 Phone System
Task List to Create the Integration with the NEC NEAX 2400 PIMG Phone System
Before doing the following tasks to integrate Cisco Unity with the NEC NEAX 2400 phone system by using PIMG units (media gateways), confirm that the Cisco Unity server is ready for the integration by completing the applicable tasks in the applicable Cisco Unity installation guide. If you are installing a new Cisco Unity server by using the applicable Cisco Unity installation guide, you may have already completed some of the following tasks.
1. Review the system and equipment requirements to confirm that all phone system and Cisco Unity server requirements have been met. See the "Requirements" section.
2. Plan how the voice messaging ports will be used by Cisco Unity. See Chapter 2, "Planning How the Voice Messaging Ports Will Be Used by Cisco Unity."
3. Program the NEC NEAX 2400 phone system and extensions. See the "Programming the NEC NEAX 2400 PIMG Phone System for Integrating with Cisco Unity" section.
4. Set up the PIMG units. See the "Setting Up the Digital PIMG Units" section.
5. Create the integration. See the "Creating an Integration with the NEC NEAX 2400 Phone System" section.
Caution Do not edit the phone configuration file (also known as the switch ini file) to customize this integration. If you change the settings in this file, the integration may not function correctly.
6. Test the integration. See Chapter 14, "Testing the Integration."
7. If you have a secondary server for Cisco Unity failover, integrate the secondary server. See Chapter 15, "Integrating a Secondary Server for Cisco Unity Failover with a PIMG Integration."
Requirements
The NEC NEAX 2400 integration supports configurations of the following components:
Phone System
•One of the following NEC NEAX 2400 phone systems:
–IMG
–IMX
–IPX (release 15 or later)
•One or more of the applicable PIMG units. For details, see Chapter 1, "Introduction."
•The voice messaging ports in the phone system connected by digital lines to the ports on the PIMG units.
We recommend that you connect the voice messaging ports on the phone system to the ports on the PIMG units in a planned manner to simplify troubleshooting. For example, the first phone system voice messaging port connects to the first port on the first PIMG unit, the second phone system voice messaging port connects to the second port on the first PIMG unit, and so on.
•The PIMG units connected to the same LAN or WAN that Cisco Unity is connected to.
•If the PIMG units connect to a WAN, the requirements for the WAN network connections are:
–For G.729a codec formatting, a minimum of 32.76 Kbps guaranteed bandwidth for each voice messaging port.
–For G.711 codec formatting, a minimum of 91.56 Kbps guaranteed bandwidth for each voice messaging port.
–No network devices that implement network address translation (NAT).
–A maximum 200 ms one-way network latency.
•The phone system ready for the integration, as described in the documentation for the phone system.
Cisco Unity Server
•Cisco Unity installed and ready for the integration, as described in the applicable Cisco Unity installation guide at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_installation_guides_list.html.
•A license that enables the applicable number of voice messaging ports.
Centralized Voice Messaging
Cisco Unity supports centralized voice messaging by supporting various inter-phone system networking protocols including, for example, proprietary protocols such as Avaya DCS, Nortel MCDN, or Siemens CorNet, and standards-based protocols such as QSIG or DPNSS. For details, see the "Centralized Voice Messaging" section in the "Integrating Cisco Unity with the Phone System" chapter of the Cisco Unity Design Guide Release 5.x at http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudgx.html.
Programming the NEC NEAX 2400 PIMG Phone System for Integrating with Cisco Unity
The following programming instructions are provided as an example only. The specific programming for your phone system may vary depending on its configuration.
Caution In programming the phone system, do not send calls to voice messaging ports in Cisco Unity that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Dialout MWI, do not send calls to it.
To Program the NEC NEAX 2400 Phone System by Using the Command Line Interface
Step 1 Log on to the NEC NEAX 2400 administration terminal and go to the Maintenance Command Menu page.
Step 2 On the Maintenance Command Menu page, enter 14 (Installation).
Step 3 On the Installation Menu page, enter 3 (ASYD) to assign system data.
Step 4 Enter the following settings.
Table 8-1 Assignment of System Data Settings
Field
|
Setting
|
Sys
|
Enter 1.
|
Index
|
Enter 78.
|
Data
|
Enter 0B.
|
Step 5 On the Maintenance Command Menu page, enter 6 (Station Data).
Step 6 On the Station Data Commands page, enter 3 (ASTN) to assign the station numbers for the voice messaging ports.
Step 7 On the Station Number Assignment page, enter the extension for the first port that will connect to the PIMG unit.
Caution Confirm that the station number (extension) is not already assigned. Otherwise, the integration will not function correctly.
Step 8 On the Station Data Commands page, enter 2 (ASCL).
Step 9 On the Station Class Data page, assign the applicable station class information to the voice messaging port.
Step 10 On the Station Data Commands page, enter 1 (ASDT).
Step 11 On the Station Data page, in the LENS field, enter the applicable line equipment number for the voice messaging port.
Step 12 On the Station Data Commands page, enter 5 (AKYD).
Step 13 On the Key Data page, select Assignment/Change and press Enter.
Step 14 On the Assignment of Key Data page, enter the following settings to enable the PRIMARY APPEARANCE function on Key 1.
Table 8-2 Assignment of Key Data Settings for Key 1
Field
|
Setting
|
KYN
|
Enter 1.
|
KYI
|
Enter 2.
|
Step 15 Press Esc to move to the next operation.
Step 16 Enter the following settings to enable the MWL SET function on Key 5.
Table 8-3 Assignment of Key Data Settings for Key 5
Field
|
Setting
|
KYN
|
Enter 5.
|
FKI
|
Enter 9.
|
Step 17 Press Esc to move to the next operation.
Step 18 Enter the following settings to enable the MWL CNCL function on Key 6.
Table 8-4 Assignment of Key Data Settings for Key 6
Field
|
Setting
|
KYN
|
Enter 6.
|
FKY
|
Enter 11.
|
Step 19 On the Maintenance Command Menu page, enter 13 (Restriction Data).
Step 20 On the Restriction Data Commands page, enter 2 (ASFC).
Step 21 On the Service Feature Assignment page, enter the following settings.
Table 8-5 Service Feature Assignment Settings
Field
|
Setting
|
TN:1
|
Enter SFI:74.
|
TN:1
|
Enter SFI:82.
|
Step 22 Program each phone to forward calls to the pilot number assigned to the voice messaging ports, based on one of the Cisco Unity call transfer types shown in Table 8-6.
Table 8-6 Call Transfer Types
Transfer Type
|
Usage
|
Release transfer
(blind transfer)
|
Program the phone to forward calls to the pilot number when:
•The extension is busy.
•The call is not answered.
|
Supervised transfer
|
Program the user station to forward calls to the pilot number only when the call is not answered (on the phone system, the number of rings before forwarding must be more than the number of rings to supervise the call). Confirm that call forwarding is disabled when the extension is busy.
|
Setting Up the Digital PIMG Units
Do the following procedures to set up the digital PIMG units that are connected to the NEC NEAX 2400 phone system.
These procedures require that the following tasks have already been completed:
•The phone system is connected to the PIMG units by using digital lines.
•The PIMG units are ready to be connected to the LAN or WAN.
•The PIMG units are connected to a power source.
Fields that are not mentioned in the following procedures must keep their default values. For the default values of all fields, see the manufacturer documentation for the PIMG units.
To Download the PIMG Firmware Update Files for Digital PIMG Units
Step 1 On a Windows workstation with a high-speed Internet connection that will have access to the PIMG units, go to the Voice and Unified Communications Downloads page at http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240.
Note To access the software download page, you must be logged on to Cisco.com as a registered user.
This procedure describes the steps when using Internet Explorer as your web browser. If you are using a different web browser, the steps may differ.
Step 2 In the tree control on the Downloads page, expand Unified Communications Applications > Voice Mail and Unified Messaging > Cisco Unity, and click Cisco Unity Telephony Integration.
Step 3 On the Log In page, enter your user name and password, then click Log In.
Step 4 On the Select a Release page, under Latest Releases, click the most recent release.
Step 5 In the right column, click the version of the firmware for digital PIMG units.
Step 6 On the Download Image page, click Download.
Step 7 On the Supporting Document(s) page, click Agree.
Step 8 In the File Download dialog box, click Save.
Step 9 In the Save As dialog box, browse to the Windows workstation that will have access the PIMG units, browse to a directory where you want to save the file, and click Save.
Step 10 In the Download Complete dialog box, click Open. The window for extracting the PIMG firmware update files appears.
Step 11 Click Extract.
Step 12 In the Extract dialog box, browse to the directory where you want the extracted files, and click Extract.
Step 13 Close the window for the extracting application.
To Set Up the Digital PIMG Units (Firmware Version 6.x)
Step 1 On the Windows workstation, add a temporary route to enable access to the PIMG units.
a. On the Windows Start menu, click Run.
b. Enter cmd, and press Enter. The Command Prompt window appears.
c. At the command prompt, enter route add 10.12.13.74 <IP Address of Workstation>, and press Enter.
For example, if the IP address of the workstation is 198.1.3.25, enter "route add 10.12.13.74<space>198.1.3.25" in the Command Prompt window.
d. Close the Command Prompt window.
Step 2 Connect a PIMG unit to the network.
Step 3 In the web browser, go to http://10.12.13.74.
Step 4 To log in, enter the following case-sensitive settings.
Table 8-7 Login Settings
Field
|
Setting
|
Username
|
Enter admin.
|
Password
|
Enter IpodAdmin.
|
Step 5 Click OK.
Step 6 On the System menu, click Upgrade.
Step 7 On the Upgrade page, click Browse.
Step 8 In the Choose File dialog box, browse to the directory on the Windows workstation that has the extracted PIMG firmware update files.
Step 9 Click Ami<xx>.app (where <xx> is multiple digits), and click Open.
Step 10 On the Upgrade page, click Install File.
Step 11 After the file is installed, a message prompting you to restart the PIMG unit appears. Click Cancel.
Caution Do not restart the PIMG unit until you are instructed to do so later in this procedure, even if the file installation fails. Restarting the PIMG unit at this step may prevent the PIMG unit from functioning correctly.
Step 12 Repeat Step 6 through Step 11 for each of the following files:
•Ami_<xx>.fsh
•Run<xx>FskEcho.dsp
•iNim<xx>.ibt
•iNim<xx>.ilc
•iNim<xx>.iap
Step 13 On the Configuration menu, click Import/Export.
Step 14 On the Import/Export page, click Browse.
Step 15 In the Choose File dialog box, browse to the file DNI_Cfg_Generic.ini.
Step 16 Click DNI_Cfg_Generic.ini, and click Open.
Step 17 On the Import/Export page, click Import File.
Step 18 After the file is imported, a message prompting you to restart the PIMG unit appears. Click OK.
Step 19 In the web browser, go to http://10.12.13.74.
Step 20 To log in, enter the following case-sensitive settings.
Table 8-8 Login Settings
Field
|
Setting
|
Username
|
Enter admin.
|
Password
|
Enter IpodAdmin.
|
Step 21 Click OK.
Step 22 On the System menu, click Password.
Step 23 On the Change Password page, enter the following settings.
Table 8-9 Change Password Page Settings
Field
|
Setting
|
Old Password
|
Enter IpodAdmin.
(This setting is case sensitive.)
|
New Password
|
Enter your new password.
(This setting is case sensitive.)
|
Confirm Password
|
Enter your new password.
(This setting is case sensitive.)
|
Step 24 Click Change.
Step 25 On the Configuration menu, click Routing Table.
Step 26 On the Routing Table page, under Router Configuration, click VoIP Host Groups.
Step 27 Under VoIP Host Groups, enter the following settings for the first VoIP host group.
Table 8-10 First VoIP Host Group Settings
Field
|
Settings
|
Name
|
Accept the default or enter another descriptive name of the VoIP host group.
|
Load-Balanced
|
(Cisco Unity without failover) Click False.
(Cisco Unity with failover configured) Click False.
|
Fault-Tolerant
|
(Cisco Unity without failover) Click False.
(Cisco Unity with failover configured) Click True.
|
Step 28 For Cisco Unity without failover, under Host List, enter the host name or IP address of the Cisco Unity server and the server port in the format <host name or IP address>:<server port>.
For Cisco Unity with failover configured, under Host List, confirm that field contains the host name or IP address of the primary Cisco Unity server and the server port in the format <host name or IP address>:<server port>.
For the server port of the first PIMG unit, enter a value (which is typically 5060) that matches the setting in UTIM of the SIP Port field for the PIMG unit. When you configure more than one PIMG unit, increase this setting by 1 for each successive unit. For example, unit 2 will be 5061, unit 3 will be 5062, and so on. This setting must match the setting in UTIM of the SIP Port field for the PIMG unit.
Step 29 For Cisco Unity without failover, continue to Step 31. For Cisco Unity with failover configured, under Host List, click Add Host.
Step 30 In the second field, enter the host name or IP address of the secondary Cisco Unity server and the server port in the format <host name or IP address>:<server port>.
For the server port of the first PIMG unit, enter a value (which is typically 5060) that matches the setting in UTIM of the SIP Port field for the PIMG unit. When you configure more than one PIMG unit, increase this setting by 1 for each successive unit. For example, unit 2 will be 5061, unit 3 will be 5062, and so on. This setting must match the setting in UTIM of the SIP Port field for the PIMG unit.
Caution Do not add a third host under Host List or a second host group under VoIP Host Groups. Otherwise, failover may not function correctly.
Step 31 Click Submit.
Step 32 Under Router Configuration, click TDM Trunk Groups.
Step 33 Under TDM Trunk Groups, click Add Trunk Group.
Step 34 Under TDM Trunk Groups, enter the following settings for the first TDM trunk group.
Table 8-11 First TDM Trunk Group Settings (Inbound Calls)
Field
|
Settings
|
Name
|
Enter Inbound_PBX_Calls or another unique name.
This TDM trunk group will handle all incoming calls from the phone system.
|
Selection Direction
|
Click Ascending.
|
Selection Mode
|
Click Linear.
|
Port/Channel Content
|
Enter the numbers of the PIMG ports that will handle inbound calls. For example, enter "*" for all PIMG ports, or enter "1-6" for the first six PIMG ports.
|
Step 35 If you will not use CPID manipulation, skip to Step 39. Otherwise, under TDM Trunk Groups, click Add Trunk Group.
Step 36 Enter the following settings for the second TDM trunk group.
Table 8-12 Second TDM Trunk Group Settings (MWIs)
Field
|
Settings
|
Name
|
Enter MWIs or another unique name.
This TDM trunk group will handle outbound MWI calls (where applicable).
|
Selection Direction
|
Click Ascending.
|
Selection Mode
|
Click Cyclic.
|
Port/Channel Content
|
Enter the numbers of the PIMG ports that will MWIs. For example, enter "*" for all PIMG ports, or enter "7,8" for the last two PIMG ports.
|
Step 37 If you will not use CPID manipulation, skip to Step 39. Otherwise, under TDM Trunk Groups, click Add Trunk Group.
Step 38 Enter the following settings for the third TDM trunk group.
Table 8-13 Third TDM Trunk Group Settings (Outbound Calls)
Field
|
Settings
|
Name
|
Enter Outbound_PBX_Calls or another unique name.
This TDM trunk group will handle all outbound calls from Cisco Unity.
|
Selection Direction
|
Click Descending.
|
Selection Mode
|
Click Linear.
|
Port/Channel Content
|
Enter * for all channels in all ports.
Enter the numbers of the PIMG ports that will handle outbound (dialout) calls. For example, enter "*" for all PIMG ports, or enter "7,8" for the last two PIMG ports.
|
Step 39 Click Submit.
Step 40 Under Router Configuration, click Inbound VoIP Rules.
Step 41 Under Inbound VoIP Rules, uncheck the Enabled check box for the default rule.
Step 42 Click Add Rule.
Step 43 If you will not use CPID manipulation, skip to Step 47. Otherwise, under Inbound VoIP Rules, enter the following settings for the first new inbound VoIP rule.
Table 8-14 First New Inbound VoIP Rule Settings (MWIs)
Field
|
Settings
|
Enable
|
Check this check box.
|
Rule Label
|
Enter MWI_Calls or another name.
This inbound VoIP rule will handle all MWI calls from Cisco Unity.
|
Request Type
|
Click Message.
|
Originating VoIP Host Address
|
Enter *.
|
Step 44 Under Inbound VoIP Request Matching, enter the following settings.
Caution The rule that you created in
Step 43 must be selected. Otherwise, any changes you make will apply to another inbound VoIP rule.
Table 8-15 Inbound VoIP Request Matching Settings
Field
|
Settings
|
Calling Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Calling Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Step 45 Under Outbound Routes, enter the following settings.
Caution The rule that you created in
Step 43 must be selected. Otherwise, any changes you make will apply to another rule.
Table 8-16 Outbound Routes Settings
Field
|
Settings
|
Device Selection
|
Outbound Destination
|
Click TDM.
|
Trunk Group
|
Click the name of the TDM trunk group that you created for MWIs in Step 36. For example, click "MWIs."
|
CPID Manipulation
|
Calling Number
|
Enter S.
|
Calling Name
|
Enter S.
|
Called Number
|
Enter D.
|
Called Name
|
Enter D.
|
Redirect Number
|
Enter R.
|
Redirect Name
|
Enter R.
|
Select Primary/Alternate Route
|
Primary
|
Click Primary.
|
Step 46 Under Inbound VoIP Rules, click Add Rule.
Step 47 Under Inbound VoIP Rules, enter the following settings for the second new inbound VoIP rule.
Table 8-17 Second New Inbound VoIP Rule Settings (Outbound Calls)
Field
|
Settings
|
Enable
|
Check this check box.
|
Rule Label
|
Enter Outbound_UC_Calls or another name.
This inbound VoIP rule will handle all outbound calls from Cisco Unity.
|
Request Type
|
Click Call.
|
Originating VoIP Host Address
|
Enter *.
|
Step 48 Under Inbound VoIP Request Matching, enter the following settings.
Caution The rule that you created in
Step 47 must be selected. Otherwise, any changes you make will apply to another rule.
Table 8-18 Inbound VoIP Request Matching Settings
Field
|
Settings
|
Calling Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Calling Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Step 49 Under Outbound Routes, enter the following settings.
Caution The rule that you created in
Step 47 must be selected. Otherwise, any changes you make will apply to another rule.
Table 8-19 Outbound Routes Settings
Field
|
Settings
|
Device Selection
|
Outbound Destination
|
Click TDM.
|
Trunk Group
|
Click the name of the TDM trunk group that you created for outbound calls in Step 38. For example, click "Outbound_PBX_Calls."
|
CPID Manipulation
|
Calling Number
|
Enter S.
|
Calling Name
|
Enter S.
|
Called Number
|
Enter D.
|
Called Name
|
Enter D.
|
Redirect Number
|
Enter R.
|
Redirect Name
|
Enter R.
|
Select Primary/Alternate Route
|
Primary
|
Click Primary.
|
Step 50 Click Submit.
Step 51 Under Router Configuration, click Inbound TDM Rules.
Step 52 Under Inbound TDM Rules, enter the following settings for the first inbound TDM rule.
Table 8-20 First Inbound TDM Rule Settings
Field
|
Settings
|
Enable
|
Check this check box.
|
Rule Label
|
Enter Inbound_Rule_1 or another name.
This inbound TDM rule will handle all incoming calls from the phone system.
|
Request Type
|
Click Call.
|
Trunk Group
|
Click the name of the TDM trunk group that you created for incoming calls from the phone system in Step 34. For example, click "Inbound_PBX_Calls."
|
Step 53 Under Inbound TDM Request Matching, enter the following settings.
Caution The rule that you created in
Step 52 must be selected. Otherwise, any changes you make will apply to another rule.
Table 8-21 Inbound TDM Request Matching Settings
Field
|
Settings
|
Calling Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Calling Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Called Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Number
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Redirect Name
|
Enter the applicable matching rule that will be used. For example, enter "*" for all.
|
Step 54 Under Outbound Routes, enter the following settings.
Caution The rule that you created in
Step 52 must be selected. Otherwise, any changes you make will apply to another rule.
Table 8-22 Outbound Routes Settings
Field
|
Settings
|
Device Selection
|
Outbound Destination
|
Click VoIP.
|
Host Group
|
Click the name of the VoIP host group that you created for Cisco Unity in Step 27.
|
CPID Manipulation
|
Calling Number
|
Enter S.
|
Calling Name
|
Enter S.
|
Called Number
|
Enter D.
|
Called Name
|
Enter D.
|
Redirect Number
|
Enter R.
|
Redirect Name
|
Enter R.
|
Select Primary/Alternate Route
|
Primary
|
Click Primary.
|
Step 55 If you want to create more Inbound TDM rules, under Inbound TDM Rules, click Add Rule. Otherwise, continue to Step 57.
Note that additional Inbound TDM rules are not necessary if you will not use CPID manipulation.
Step 56 Repeat Step 52 through Step 55 for all remaining inbound TDM rules that you want to create.
Step 57 Click Submit.
Step 58 On the Configuration menu, click TDM > Digital.
Step 59 On the Digital Telephony page, in the Telephony Switch Type field, click NEC_NEAX.
Step 60 Click Submit.
Step 61 On the Configuration menu, click TDM > General.
Step 62 On the TDM General Settings page, enter the following settings.
Table 8-23 TDM General Settings Page Settings
Field
|
Settings
|
PCM Coding
|
Click uLaw.
|
Minimum Call Party Delay (ms)
|
Enter 500.
|
Maximum Call Party Delay (ms)
|
Enter 2000.
|
Dial Digit on Time (ms)
|
Enter 100.
|
Dial Inter-Digit Time (ms)
|
Enter 100.
|
Dial Pause Time (ms)
|
Enter 2000.
|
Turn MWI On FAC
|
Leave this field blank.
|
Turn MWI Off FAC
|
Leave this field blank.
|
Outbound Call Connect Timeout (ms)
|
Enter 10000.
|
Wait for Ringback/Connect on Blind Transfer
|
Click Yes.
|
Hunt Group Extension
|
Enter the pilot number of the Cisco Unity voice messaging ports.
|
Step 63 Click Submit.
Step 64 On the Configuration menu, click TDM > Port Enable.
Step 65 On the TDM Port Enabling page, click No for the ports that you want to disable on the PIMG unit.
Step 66 Confirm that Yes is selected for all other ports on the PIMG unit.
Step 67 Click Submit.
Step 68 On the Configuration menu, click VoIP > General.
Step 69 On the VoIP General Settings page, enter the following settings.
Table 8-24 VoIP General Settings Page Settings
Field
|
Setting
|
User-Agent
|
Host and Domain Name
|
Enter the domain name of the PIMG unit.
|
Transport Type
|
Click UDP.
|
Call as Domain Name
|
Click No.
|
Invite Expiration (sec)
|
Enter 120.
|
Server
|
DNS Server Address
|
Enter the IP Address of the Domain Name Server that the PIMG unit will use.
|
Registration Server Address
|
Leave this field blank.
|
Registration Server Port
|
Enter 5060.
|
Registration Expiration (sec)
|
Enter 3600.
|
TCP/UDP
|
UDP/TCP Transports Enabled
|
Click Yes.
|
TCP/UDP Server Port
|
Enter 5060.
|
Proxy
|
Primary Proxy Server Address
|
Leave this field blank.
|
Primary Proxy Server Port
|
Not applicable. Leave the default setting.
|
Backup Proxy Server Address
|
Not applicable. Leave the default setting.
|
Backup Proxy Server Port
|
Not applicable. Leave the default setting.
|
Proxy Query Interval
|
Enter 10.
|
Timing
|
T1 Time (ms)
|
Enter 400.
|
T2 Time (ms)
|
Enter 3000.
|
Monitoring
|
Monitor Call Connections
|
Click No.
|
Step 70 Click Submit.
Step 71 On the Configuration menu, click VoIP > Media.
Step 72 On the VoIP Media Settings page, enter the following settings.
Table 8-25 VoIP Media Settings Page Settings
Field
|
Settings
|
Audio
|
Audio Compression
|
Click the preferred codec for audio compression.
|
RTP Digit Relay Mode
|
Click RFC2833.
|
Signaling Digit Relay Mode
|
Click Off.
|
Voice Activity Detection
|
Click Off.
|
Frame Size
|
Click the applicable setting:
•G.711—20
•G.729AB—10
Caution Failure to use the correct setting will result in recorded messages containing nothing but silence.
|
Frames Per Packet
|
Click the applicable setting:
•G.711—1
•G.729AB—2
Caution Failure to use the correct setting will result in recorded messages containing nothing but silence.
|
Step 73 Click Submit.
Step 74 On the Configuration menu, click VoIP > QOS.
Step 75 On the VoIP QOS Configuration page, enter the following settings.
Table 8-26 VoIP QOS Configurative Page Settings
Field
|
Settings
|
Call Control QOS Byte
|
Enter 104.
|
RTP QOS Byte
|
Enter 184.
|
Step 76 Click Submit.
Step 77 On the Configuration menu, click IP.
Step 78 On the IP Settings page, enter the following settings.
Table 8-27 IP Settings Page Settings
Field
|
Settings
|
Client IP Address
|
Enter the new IP address you want to use for the PIMG unit.
(This is the IP address that you enter in UTIM when you create the integration.)
|
Client Subnet Mask
|
Enter the new subnet mask, if the subnet mask is different from the default IP address.
|
Default Network Gateway Address
|
Enter the IP address of the default network gateway router that the PIMG units will use.
|
BOOTP Enabled
|
Click No.
|
Step 79 Click Submit.
Step 80 On the Configuration menu, click Tone Detection.
Step 81 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn Tone Event field, click Busy and do the following substeps to verify that the tone is correct.
a. From a available phone, call a second phone.
b. Answer the second phone when it rings, and leave both handsets off so that both phones are busy.
c. From a third phone, dial one of the busy phones.
d. Confirm that you hear a busy tone.
e. Hang up the third phone but leave the handsets for the other two phones off.
Step 82 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 81c. from the third phone.
Step 83 Click Learn.
Step 84 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn field, click Error and do the following substeps to verify that the tone is correct.
a. From an available phone, dial an extension that does not exist.
b. Confirm that you hear the reorder or error tone.
c. Hang up the phone.
Step 85 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 84a.
Step 86 Click Learn.
Step 87 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn field, click Ringback and do the following substeps to verify that the tone is correct.
a. From an available phone, dial an extension that does exist.
b. Confirm that you hear the ringback tone.
c. Hang up the phone.
Step 88 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 87a.
Step 89 Click Learn.
Step 90 Click Submit.
Step 91 Hang up the phones that you used in Step 81.
Step 92 On the System menu, click Restart.
Step 93 On the Restart page, click Restart Unit Now.
Step 94 Repeat Step 2 through Step 93 on all remaining PIMG units.
If your Cisco Unity system must have an RTP port range of 16384 to 32767, do the following procedure.
Caution You must set the RTP port range for the PIMG units if your system uses an RTP port range of 16384 to 32767. Otherwise, Cisco Unity will not be able to answer calls, and callers will hear ringing or silence.
Note The default RTP port range for PIMG units is 49000 to 50000. Some Cisco Unity configurations require a different RTP port range.
To Set the RTP Port Range for PIMG Units
Step 1 On a Windows workstation that has access to the PIMG units, open a web browser and browse to the first PIMG unit.
Step 2 Log in to the PIMG unit.
Step 3 On the Configuration menu, click Import/Export.
Step 4 On the Import/Export page, under Export Files, click Export All Settings.
Step 5 In the File Download dialog box, click Save.
Step 6 In the Save As dialog box, browse to the Windows workstation that has access to the PIMG units, browse to a directory where you want to save the file, and click Save.
Step 7 In the Download Complete dialog box, click Open. Notepad opens the file Config.ini that you saved.
Step 8 Locate the line with the following parameter:
Step 9 Change the value of the parameter to 16384 so that the line reads as follows:
Step 10 Locate the line with the following parameter:
Step 11 Change the value of the parameter to 32767 so that the line reads as follows:
Step 12 Save the file, and exit Notepad.
Step 13 On the Configuration menu of the PIMG unit, click Import/Export.
Step 14 On the Import/Export page, under Browse for Import File, click Browse.
Step 15 In the Choose File dialog box, browse to the file Config.ini that you saved.
Step 16 Click Config.ini, and click Open.
Step 17 On the Import/Export page, click Import File.
Step 18 When prompted to restart the PIMG unit, click OK.
Step 19 Repeat this procedure for all remaining PIMG units.
Creating an Integration with the NEC NEAX 2400 Phone System
After ensuring that the NEC NEAX 2400 phone system, the PIMG units, and the Cisco Unity server are ready for the integration, do the following procedures to set up the integration and to enter the port settings.
To Create an Integration
Step 1 If UTIM is not already open, on the Windows Start menu of the Cisco Unity server, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 2 In the left pane of the UTIM window, click Cisco Unity Server.
Step 3 On the Integration menu of the UTIM window, click New. The Telephony Integration Setup Wizard appears.
Step 4 On the Welcome page, click Circuit-switched via Intel PIMG and click Next.
Step 5 On the Name the Phone System Integration page, accept the default name or enter the phone system name to identify this integration, then click Next.
Step 6 On the Enter PIMG Settings page, click Add.
Step 7 In the Add PIMG dialog box, enter the following settings, then click OK.
Table 8-28 Settings for the Add PIMG Dialog Box
Field
|
Setting
|
Display Name
|
Accept the default name or enter another name to identify this PIMG unit.
|
IP Address
|
Enter the IP address of this PIMG unit.
|
SIP Port
|
For the first PIMG unit, enter 5060.
When you configure more than one PIMG unit, increase this setting by 1 for each successive unit. For example, unit 2 will be 5061, unit 3 will be 5062, and so on. This setting must match the server port setting on the VoIP Host Group page of the PIMG unit.
|
Phone Lines (Ports) Connected
|
Enter 8.
If you want to use fewer than eight voice messaging ports, enter the number of ports (or phone lines) that you want to use with this PIMG unit.
|
Step 8 Repeat Step 6 and Step 7 for each remaining PIMG unit that you are connecting to the Cisco Unity server.
You can press the following buttons to modify, delete, or verify the PIMG units that you are connecting to the Cisco Unity server.
Table 8-29 Buttons on the Enter PIMG Settings Page
Field
|
Setting
|
Add
|
Displays the Add PIMG dialog box to add another PIMG unit to the integration.
|
Modify
|
Displays the Modify PIMG dialog box so that you can modify the settings of the selected PIMG unit.
|
Delete
|
Deletes the selected PIMG unit from the integration.
|
Ping Servers
|
Confirms that the IP address is correct for all PIMG units.
|
Licensing
|
Displays a list of the licensed, used, and available voice messaging ports on the Cisco Unity server.
|
Step 9 On the Enter PIMG Settings page, click Next.
Step 10 On the PIMG Integration with the PBX page, click No, the PIMGs Do Not Require a Serial Connection to the PBX, then click Next.
Step 11 On the Configure Cisco Unity SIP Settings page, enter the following settings, then click Next.
Table 8-30 Settings for the Configure Cisco Unity SIP Settings Page
Field
|
Setting
|
Contact Line Name
|
(Cisco Unity without failover) Enter the voice messaging line name that subscribers use to contact Cisco Unity and that Cisco Unity will use to register with the PIMG units.
(Cisco Unity with failover configured) Enter the name the primary Cisco Unity server. This setting must match the Port X Endpoint parameter settings in the PIMG administration. This setting must be the same for both the primary and the secondary Cisco Unity servers.
|
Cisco Unity SIP Port
|
Enter the IP port on Cisco Unity that callers and the SIP server use to connect to voice mail. We recommend using the default setting.
|
Preferred Codec
|
Enter the codec that Cisco Unity will first attempt to use on outgoing calls.
|
Step 12 If other integrations already exist, the Enter Trunk Access Code page appears. Enter the extra digits that Cisco Unity must use to transfer calls through the gateway to extensions on the other phone systems with which it is integrated. Then click Next.
Step 13 On the Reassign Subscribers page, any subscribers whose phone system integration has been deleted and who are not currently assigned to a phone system integration will appear in the list.
If no subscribers appear in the list, click Next and continue to Step 14.
Otherwise, select the subscribers that you want to assign to this phone system integration and click Next. You can use the following selection controls for selecting subscribers.
Table 8-31 Selection Controls for the Reassign Subscribers Page
Selection Control
|
Effect
|
Check All
|
Checks the check boxes for all subscribers in the list.
|
Uncheck All
|
Unchecks the check boxes for all subscribers in the list.
|
Toggle Selected
|
For the subscribers highlighted in the list, toggles between checking and unchecking the check boxes.
If some highlighted subscriber check boxes are checked and others are unchecked, clicking this button will check all the check boxes. Clicking again will uncheck all the check boxes.
|
Step 14 On the Reassign Call Handlers page, any call handlers whose phone system integration has been deleted and that are not currently assigned to a phone system integration will appear in the list.
If no call handlers appear in the list, click Next and continue to Step 15.
Otherwise, select the call handlers that you want to assign to this phone system integration and click Next. You can use the following selection controls for selecting call handlers.
Table 8-32 Selection Controls for the Reassign Call Handlers Page
Selection Control
|
Effect
|
Check All
|
Checks the check boxes for all call handlers in the list.
|
Uncheck All
|
Unchecks the check boxes for all call handlers in the list.
|
Toggle Selected
|
For the call handlers highlighted in the list, toggles between checking and unchecking the check boxes.
If some highlighted call handler check boxes are checked and others are unchecked, clicking this button will check all the check boxes. Clicking again will uncheck all the check boxes.
|
Step 15 On the Completing page, verify the settings you entered, then click Finish.
Step 16 At the prompt to restart the Cisco Unity services, click Yes. The Cisco Unity services restart.
Alternatively, you can restart the Cisco Unity services in UTIM on the Tools menu by clicking Restart Cisco Unity.
To Enter the Voice Messaging Port Settings for the Integration
Step 1 After the Cisco Unity services restart, on the View menu, click Refresh.
Step 2 In the left pane of the UTIM window, expand the phone system integration that you are creating.
Step 3 In the left pane, click the name of the first PIMG unit.
Step 4 In the right pane, click the Ports tab.
Step 5 Enter the settings shown in Table 8-33 for the voice messaging ports.
For best performance, use the first voice messaging ports for incoming calls and the last ports to dial out. This helps minimize the possibility of a collision, in which an incoming call arrives on a port at the same time that Cisco Unity takes the port off-hook to dial out.
Caution In programming the phone system, do not send calls to voice messaging ports in Cisco Unity that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Message Notification, do not send calls to it.
Table 8-33 Settings for the Voice Messaging Ports
Field
|
Considerations
|
Extension
|
Enter the extension for the port as assigned on the phone system.
|
Enabled
|
Check this check box to enable the port. The port is enabled during normal operation.
Uncheck this check box to disable the port. When the port is disabled, calls to the port get a ringing tone but are not answered. Typically, the port is disabled only by the installer during testing.
|
Answer Calls
|
Check this check box to designate the port for answering calls. These calls can be incoming calls from unidentified callers or from subscribers.
|
Message Notification
|
Check this check box to designate the port for notifying subscribers of messages. Assign Message Notification to the least busy ports.
|
Dialout MWI
|
Check this check box to designate the port for turning MWIs on and off. Assign Dialout MWI to the least busy ports.
|
AMIS Delivery
(available with the AMIS licensed feature only)
|
Check this check box to designate the port for making outbound AMIS calls to deliver voice messages from Cisco Unity subscribers to users on another voice messaging system. Cisco Unity supports the Audio Messaging Interchange Specification (AMIS) protocol, which provides an analog mechanism for transferring voice messages between different voice messaging systems.
This setting affects outbound AMIS calls only. All ports are used for incoming AMIS calls.
Because the transmission of outgoing AMIS messages may tie up voice ports for long periods of time, you may want to adjust the schedule on the Network > AMIS > Schedule page so that outgoing AMIS calls are placed during closed hours or at times when Cisco Unity is not processing many calls.
|
TRAP Connection
|
Check this check box so that subscribers can use the phone as a recording and playback device in Cisco Unity web applications and e-mail clients. Assign TRAP Connection to the least busy ports.
|
Step 6 Click Save.
Step 7 Click the SIP Info tab.
Step 8 Uncheck the Register with SIP Server check box and click Save.
Step 9 At the prompt to restart the Cisco Unity services, click No.
Step 10 Repeat Step 3 through Step 9 for all remaining PIMG units.
Step 11 In the left pane, click Properties for the phone system.
Step 12 In the right pane, click the PIMG tab.
Step 13 Click Save.
Step 14 At the prompt to restart the Cisco Unity services, click Yes.
Step 15 After the Cisco Unity services restart, exit UTIM.
Caution Do not edit the phone configuration file (also known as the switch ini file) to customize this integration. If you change the settings in this file, the integration may not function correctly.
If the number of voice messaging ports on the Cisco Unity server is 72 or more, and the Cisco Unity server is running Windows Server 2003 or Exchange is the message store, do the following procedure.
To Adjust the Advanced Settings for 72 or More Voice Messaging Ports
Step 1 On the Cisco Unity server, on the Windows Start menu, click Programs > Cisco Unity > Cisco Unity Tools Depot.
Step 2 In the Tools Depot window, in the left pane, expand Administration Tools and double-click Advanced Settings Tool.
Step 3 If the Cisco Unity server is running Windows Server 2003, do the following substeps. Otherwise, continue to Step 4.
a. In the Cisco Unity Advanced Settings window, in the left pane, click Messaging - 72 or More Voice Ports - Enable Low-Fragmentation Heap.
b. In the New Value drop-down box, click 1 and click Set.
c. When prompted that the value has been set, click OK.
Step 4 If Exchange is the message store, do the following substeps. Otherwise, continue to Step 5.
a. In the Cisco Unity Advanced Settings window, in the left pane, click Messaging - 72 or More Voice Ports - Number of MAPI Sessions Per Exchange Server.
b. In the New Value drop-down box, click the applicable setting, then click Set.
Number of Voice Messaging Ports
|
Setting
|
72 to 83
|
Click 2.
|
84 to 95
|
Click 3.
|
96 to 119
|
Click 4.
|
120 to 143
|
Click 5.
|
144
|
Click 6.
|
c. When prompted that the value has been set, click OK.
Step 5 Close the Tools Depot window.
Step 6 Restart the Cisco Unity server.
