Cisco Unity Installation Guide (With IBM Lotus Domino), Release 4.0(2)
Setting Up the Hardware

Table Of Contents

Setting Up the Hardware

Installing Voice Cards

Attaching Peripheral Devices and Connecting the Phone System


Setting Up the Hardware



Note Cisco ICS 7750: If you are installing Cisco Unity in the Cisco ICS 7750, skip this chapter.


In this chapter, you do the following tasks in the order listed:

1. With circuit-switched phone systems only: Install voice cards. See the "Installing Voice Cards" section.

2. Set up the Cisco Unity computer. See the "Attaching Peripheral Devices and Connecting the Phone System" section.

When you are finished with this chapter, return to the Task List for Installing Cisco Unity on a Qualified Server, to continue installing the Cisco Unity system correctly.


Note The tasks in the list reference detailed instructions in the Cisco Unity Installation Guide and in other Cisco Unity documentation. Follow the documentation for a successful installation.


Installing Voice Cards


Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.



Warning Read the installation instructions before connecting the system to the power source.



Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.



Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.



Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.



Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
 · This unit should be mounted at the bottom of the rack if it is the only unit in
  the rack.
 · When mounting this unit in a partially filled rack, load the rack from the
  bottom to the top with the heaviest component at the bottom of the rack.
 · If the rack is provided with stabilizing devices, install the stabilizers before
  mounting or servicing the unit in the rack.



Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages.



Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.



Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.



Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.



Warning This equipment is to be installed and maintained by service personnel only as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel.



Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards.



Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.


To install voice cards


Step 1 If the computer is already on, exit the Cisco Unity software, if applicable, then shut down the computer. For more information, see "Exiting and Starting the Cisco Unity Software and Server."

Step 2 Attach an antistatic wrist strap, and ground yourself to the computer.


Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.


Step 3 Set the switches and jumpers on each card. See "Voice Cards," for information on hardware settings for your cards.

Some cards include hardware settings that indicate which card is first, which is second, and so on. If you are installing more than one card of the same model, keep the cards in order so you can install them in the correct order in Step 4.

If you are installing Intel Dialogic D/120JCT-Euro or D/240PCI-T1 cards, do not do the procedure under "Software Settings" in "Voice Cards," at this time. The Cisco Unity Installation Guide alerts you when to do the procedure later in the installation process.

Step 4 Insert each card firmly into its slot, and fasten each card to the computer backplate with a screw. Note the following considerations, if applicable:

If you are installing more than one card of the same model, and if the cards include a hardware setting that indicates which card is first, second, and so on, install the cards in the order specified by the hardware settings.

If you are installing cards of different models in the same server, install cards of the same model adjacent to one another.

All cards with H.100 bus (also known as CT bus) connectors must be installed in the same computer. If all the cards do not fit in the Cisco Unity computer, then you must install all of them in an expansion chassis.

PCI cards can be put into either 32-bit or 64-bit, 33-MHz PCI slots.


Caution Placing a 33-MHz Intel Dialogic voice card in a physical interface slot in the same logical segment as a 66-MHz PCI or 100-to-133-MHz PCI-X interface card will slow down the card to 33 MHz, degrading performance of the whole platform.

Step 5 If you are installing a PCI expansion chassis: Install the host card in an applicable slot, depending on the platform. Use the required slots with the following platforms:

Dell PowerEdge 4400

Slot 1

Hewlett-Packard DL580G1

Slot 6

Hewlett-Packard DL580G2

Slot 4 to 6

Hewlett-Packard ML570G1

Slot 6

Hewlett-Packard ML570G2

Slot 4 to 6

IBM x Series 232

Slot 4

IBM x Series 342

Slot 4

IBM x Series 345

Slot 3 or 5


For supported platforms that are not listed above, the host card can be installed in any slot. (For the platforms that support using an expansion chassis, refer to Cisco Unity Supported Platforms List, on Cisco.com at http://www.cisco.com/warp/public/cc/pd/unco/un/prodlit/ucutp_st.htm.)

Note that if the slot location of a customer-provided server management card (such as Hewlett-Packard Remote Insight Lights-Out Edition or Dell Remote Assistant Card) conflicts with a required host card slot, the host card takes precedence.

Step 6 If you are installing a PCI expansion chassis: Insert each card firmly into its slot and fasten each card to the computer backplate with a screw.

Step 7 If you are installing multiple voice cards that have H.100 bus connectors, cable the cards together. On each card, connect the cable so the red stripe on the cable corresponds with pin 1 on the card connector. Confirm that the connectors are firmly seated.


Caution If you do not cable cards together as required, the voice card software will not start, and Cisco Unity will not answer calls.

If the cable has more connectors than the computer has voice cards, use the first and last connectors, and leave unused connectors in the middle of the cable. If the end of a cable is allowed to dangle loose, it can act as a radio antenna and pick up noise from the bus.

If you are cabling three or more cards together, connect the first connector on the cable to the first card, the second connector to the second card, and so on.


Attaching Peripheral Devices and Connecting the Phone System

Cisco recommends that you connect the Cisco Unity computer to a dedicated uninterruptible power supply.

A Cisco Unity computer purchased from Cisco is configured for a specific hardware setup. Do not add or change any hardware on the computer, except to add voice cards, memory, a tape drive, an external modem, or a rail kit.

To attach peripheral devices and connect the phone system


Step 1 Place the computer in a dry, cool area that is free of dust. If you are connecting the Cisco Unity computer to the network, place it near a network connection. If you are integrating Cisco Unity with a circuit-switched phone system, place the computer near the phone system.

Step 2 Attach peripheral devices—such as an external modem or a printer—to the computer. Follow the manufacturer installation and test instructions.


Caution Do not attach the network cable to the computer until you have installed Windows 2000 Server Service Pack 3. Service Pack 3 includes the Microsoft Internet Information Services Cumulative Hot Fix Q301625. The Cisco Unity Installation Guide alerts you when to install the service pack and when to connect to the network later in the installation process.

Step 3 If you are integrating Cisco Unity with a circuit-switched phone system: Connect the phone system to the computer as described in the Cisco Unity integration guide for your phone system. (Cisco Unity integration guides are available on Cisco.com at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_configuration_guides_list.html.)

For pinout information, see the section for your voice card(s) in "Voice Cards."

Step 4 If you are installing the Cisco Unity system outside the United States and the computer contains voice cards that came with a ferrite clamp, attach the clamp around the analog phone lines as close to the computer as possible.