In the
Unified CVP Operations Console, navigate to SNMP > V1/V2c > Community String .
Step 2
Click Add New.
Name the community string.
Select the Devices tab and assign the SNMP community string to a device.
Click Save and Deploy.
Step 3
Create the notification destination and deploy to all of the Unified CVP
devices.
Navigate to SNMP > V1/V2c > Notification Destination.
Complete the fields.
Select the Devices tab and assign the SNMP notification destination to a device.
Click Save and Deploy.
Configure SIP Server Group
SIP Server Groups
are required for Cisco Unified Communications Manager and Gateways.
Procedure
Step 1
In the Unified
CVP Operations Console, navigate to
System > SIP Server
Group .
Step 2
Create a server
group for the Cisco Unified Communications Manager devices:
On the
General tab, click
Add
New.
Fill in the
SRV
Domain Name FQDN field with a value that will also be used in the
Cluster FQDN setting in Enterprise Parameters in Communications Manager. For
example, cucm.cisco.com.
In the
IP
Address/Hostname field, enter an IP address or hostname for the
Unified Communications Manager node.
Click
Add.
Repeat Steps
c and d for each Unified Communications Manager subscriber. Click
Save.
Note
Do not put
the Publisher node in the server group.
SIP server group for Communications Manager is not required
for SCC deployment as there is no direct SIP trunk created from Communications
Manager to CVP in SCC model.
The FQDN should
match the FQDN configured in the Cluster FQDN setting that will be configured in Enterprise Parameters on the Cisco
Unified Communications Manager. See Configure Fully-Qualified Domain Name
Step 3
Create a server
group for the gateway devices:
On the
General tab, click
Add
New.
In the
SRV
Domain Name FQDN field, enter the SRV Domain Name FQDN. For example
vxmlgw.cisco.com.
In the
IP
Address/Hostname field, enter an IP address or hostname for each
gateway.
Click
Add.
Repeat Steps
c and d for the gateway. Click
Save.
Add all VXML
gateways as appropriate for deployment and branches. Adding all VXML gateways
to the server group will load balance calls across all the member server group
gateways.
Step 4
Associate these
server groups to all Unified CVP Call Servers:
On the
Call
Server Deployment tab, move all Unified CVP Call Servers from the
Available list to the
Selected list.
Click
Save
and Deploy.
Configure dialed
number patterns
Dialed number
patterns are required for:
Agent Device
Network VRU
Ringtone
Error
Procedure
Step 1
In the Unified
CVP Operations Console, navigate to
System > Dialed Number
Pattern.
Step 2
For each dialed
number pattern in the table below:
Click Add New.
In the
Dialed Number Pattern field, enter the dialed number
pattern.
In the
Description field, enter a description for the
dialed number pattern.
In the
Dialed Number Pattern Types pane, check the
specified dialed number pattern types.
Click
Save.
Step 3
After you
configure all dialed number patterns, click
Deploy.
Step 4
Click
Deployment Status to make sure that you applied the
configuration.
Dialed number pattern
Description
Dialed number pattern types
91*
Ringtone
Check
Enable Local Static Route.
Route to SIP Server Group and IP Address/Hostname/Server Group
Name are both VXML Gateway (for example, vxmlgw.cisco.com).
Check
Enable Send Calls to Originator.
92*
Error
Check
Enable Local Static Route.
Route to SIP Server Group and IP Address/Hostname/Server Group
Name are both VXML Gateway (for example, vxmlgw.cisco.com).
Check
Enable Send Calls to Originator.
The
agent extension pattern. For example, enter 500* where the range of agent
extensions is 5001 to 500999.
Agent Device. Not applicable to SCC Deployment model.
Check
Enable Local Static Route.
Route to SIP Server Group and IP Address/Hostname/Server Group
Name are both the Unified Communications Manager gateway.
Check
Enable RNA Timeout for Outbound Calls. The timeout
is 15 seconds.
777*
Network VRU Label
Check
Enable Local Static Route.
Route to SIP Server Group and IP Address/Hostname/Server Group
Name are both VXML Gateway (for example vxmlgw.cisco.com).