Feedback
Contents
Status and configuration
View cluster node information
ProcedureView hardware status
Procedure
Table 2 Hardware status field descriptions Field Description Platform Type Displays the model identity of the platform server.
Serial Number Displays the serial number of the platform server.
Processor Speed Displays the processor speed.
CPU Type Displays the type of processor in the platform server.
Memory Displays the total amount of memory in MB.
Object ID Displays the object ID.
OS Version Displays the operating system version.
RAID Details Displays details about the RAID drive, including controller information, logical drive information, and physical device information.
Display network status
ProcedureThe network status information that appears depends on if Network Fault Tolerance is enabled. When Network Fault Tolerance is enabled, Ethernet port 1 automatically takes over network communications if Ethernet port 0 fails. If Network Fault Tolerance is enabled, network status information appears for the network ports Ethernet 0, Ethernet 1, and Bond 0. If Network Fault Tolerance is not enabled, status information appears only for Ethernet 0.
To view the network status, follow this procedure:
Table 3 Network settings field descriptions Field Description Ethernet Details DHCP Disabled for Unified CCX 9.0(1).
Status Indicates whether the port is Up or Down for Ethernet ports 0 and 1.
IP Address Shows the IP address of Ethernet port 0 [and Ethernet port 1 if Network Fault Tolerance (NFT) is enabled].
IP Mask Shows the IP mask of Ethernet port 0 (and Ethernet port 1 if NFT is enabled).
Link Detected Indicates whether an active link exists.
Queue Length Displays the length of the queue.
MTU Displays the maximum transmission unit.
MAC Address Displays the hardware address of the port.
License MAC Displays the license MAC.
Receive Statistics (RX) Displays information on received bytes, packets, and errors, as well as dropped and overrun statistics.
Transmit Statistics (TX) Displays information on transmitted bytes, packets, and errors, as well as dropped, carrier, and collision statistics.
DNS Details Primary Displays the IP address of the primary domain name server.
Secondary Displays the IP address of the secondary domain name server.
Options Displays the configured DNS options.
Domain Displays the domain of the server.
Gateway Displays the IP address of the network gateway on Ethernet port 0.
Verify installed software
Procedure
Table 4 Software packages field descriptions Field Description Partition Versions Displays the software version that is running on the active and inactive partitions.
Installed Software Options Active Version Installed Software Options Displays the versions of installed software options, including Cisco Options Package (COP) patch files that are installed on the active version.
Inactive Version Installed Software Options Displays the versions of installed software options, including COP patch files that are installed on the inactive version.
View system status
Procedure
Table 5 System status field descriptions Field Description Host Name Displays the name of the Cisco MCS host where Cisco Unified Communications Operating System is installed.
Date Displays the date and time based on the continent and region that were specified during operating system installation.
Time Zone Displays the time zone that was chosen during installation.
Locale Displays the language that was chosen during operating system installation.
Product Version Displays the operating system version.
Platform Version Displays the platform version.
License MAC Displays the license MAC.
Uptime Displays system uptime information.
CPU Displays the percentage of CPU capacity that is idle, the percentage that is running system processes, and the percentage that is running user processes.
Memory Displays information about memory usage, including the amount of total memory, free memory, and used memory in KBytes.
Disk/active Displays the amount of total, free, and used disk space on the active disk.
Disk/inactive Displays the amount of total, free, and used disk space on the inactive disk.
Disk/logging Displays the amount of total, free, and disk space that is used for disk logging.
Display registered ports
ProcedureYou can use the IP Preferences window to display a list of registered ports that the system can use. The IP Preferences window contains the following information:
Step 1 From the Cisco Unified Communications Operating System Administration window, choose . The IP Preferences window appears. Records from an active (prior) query may also appear in the window. Step 2 To find all records in the database, ensure the dialog box is empty and go to Step 4. Step 3 To filter or search records, do the following:
- From the first drop-down list box, select a search parameter.
- From the second drop-down list box, select a search pattern.
- Specify the appropriate search text, if applicable.
Note To add additional search criteria, click the + button. When you add criteria, the system searches for a record that matches all criteria that you specify. To remove criteria, click the – button to remove the last added criterion or click the Clear Filter button to remove all added search criteria.
Step 4 Click Find. All matching records appear. You can change the number of items that appear on each page by choosing a different value from the Rows per Page drop-down list box.
The following table contains descriptions of the IP Preferences fields.
Table 6 IP preferences field descriptions Field Description Application Name of the application using (listening on) the port.
Protocol Protocol used on this port (TCP, UDP).
Port Number Numeric port number.
Type Translated Port Traffic destined for this port is forwarded to the port listed in the Port Number column. This field applies to Translated type ports only.
Status Description Brief description of how the port is used.