Worldwide [change] |Account |Register |About Cisco
Guest

Hierarchical Navigation

Cisco Network Modules

Release Notes for Cisco Unified SIP Proxy 1.1.2

Downloads

Table Of Contents

Release Notes for Cisco Unified SIP Proxy 1.1.2

Contents

Introduction

System Requirements

Hardware Supported

Software Compatibility

Determining the Software Version

Installation Notes

Limitations and Restrictions

Caveats

Open Caveats

Related Documentation

Obtaining Documentation and Submitting a Service Request


Release Notes for Cisco Unified SIP Proxy 1.1.2

First Published: February 20, 2009
Last Revised: February 19, 2009
OL-18701-01

This document describes the new features, system requirements, and caveats for Cisco Unified SIP Proxy 1.1.2. Use this document in conjunction with the documents listed in the "Related Documentation" section.

Contents

This document includes the following sections:

•Introduction

•System Requirements

•Installation Notes

•Limitations and Restrictions

•Related Documentation

•Obtaining Documentation and Submitting a Service Request

Introduction

Cisco Unified SIP Proxy is designed to help connect and manage SIP networks. The Cisco Unified SIP Proxy module is designed to be an integrated solution in Cisco 3800 Series Integrated Services Routers (Cisco ISRs). The module provides multiple features including name resolution, routing, scalability, and high availability.

System Requirements

Hardware Supported

The Cisco Unified SIP Proxy module runs the NME-522 module. The part number of the Cisco  Unified SIP Proxy module is NME-CUSP-522-K9. The module has 2 GB of RAM and 160 GB HDD. This module installs only on the Cisco 3825 or 3845 ISRs.

Software Compatibility

The Cisco Unified SIP Proxy module requires Cisco IOS Release 12.4(22)T or a later release on the Cisco ISR.

Determining the Software Version

To determine the software version and the license used, perform the following steps:

Step 1 Open a Telnet session.

Step 2 Telnet to the router by entering telnet ip-address.

Step 3 Enter the user ID and password of the router.

Step 4 Enter the following command to enter the command environment:

enable

<router password>

service-module service-engine slot/port session

Step 5 Enter the following command to display the Cisco Unified SIP Proxy software version:

show software versions

Step 6 Enter the following command to enter Cisco Unified SIP Proxy execution mode:

cusp

Step 7 Enter the following command to display the Cisco Unified SIP Proxy software license:

show license

For information about IOS open source licensing, see the Notices section in the About Cisco IOS Release Notes at:

http://www.cisco.com/en/US/docs/ios/12_4/12_4x/12_4xy15/ReleaseNote.html#wp398419

Installation Notes

The software is already loaded at the factory, and you can install or upgrade it using the command:

software install clean ftp://x.x.x/file_name

There are three software files, all of which you should save to the FTP directory. You need to load the .pkg file, the other files are downloaded automatically. See Table 1.

.

Table 1 Software Files

Name
Size

cusp-k9.nme.x.x.pkg

100 KB

cusp-full-k9.nme.x.x.prt1

87 MB

cusp-installer-k9.nme.x.x.prt1

128 KB


Limitations and Restrictions

•This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer, and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute, or use encryption. Importers, exporters, distributors, and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html.

If you require further assistance send an email to export@cisco.com.

•Voice and router functions may co-reside in the same router with Cisco Unified SIP Proxy with two exceptions:

–Cisco Unified SIP Proxy may not co-reside in the same router when Cisco Unified Communications Manager Express (Cisco Unified CME) or Cisco Unified Survivable Remote Site Telephony (Cisco Unified SRST) are configured for SCCP phones.

–Cisco Unified SIP Proxy may not co-reside in the same router with time division multiplex (TDM) gateways or configuration of H.323 dial peers (including Cisco Unified Border Element).

Cisco Unified CME, Cisco Unified SRST, and Cisco Unified Border Element (Cisco UBE) configured for SIP may co-reside in the same router.

Caveats

This section contains only open caveats for Cisco Unified SIP Proxy 1.0.

•Open Caveats

These caveats describe unexpected behavior in Cisco Unified SIP Proxy software releases. Severity 1 caveats are the most serious caveats. Severity 2 caveats are less serious. Severity 3 caveats are moderate caveats, and only selected severity 3 caveats are included in the caveats document.

Note If you have an account on Cisco.com, you can use Bug Toolkit to find caveats of any severity. The Bug Toolkit is at: http://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl

Open Caveats 

CSCsu48446 software install clean command is failing.

Symptom    When attempting to boot after doing a clean install, a message displays that says: "corrupted bzImage detected." The boot then halts.

Conditions   Unknown, occasionally occurs after issuing a "software install clean".

Workaround   Boot the helper image, and reinstall. The blade will now boot. 

CSCsx65091 java.lang.OutOfMemoryError at CUSP when doing show trace log.

Symptom    CLI access to CUSP goes to unresponsive mode when executing show trace log command. 

CSCsw97960 4 NIC support in CARS 1.2.

Symptom    There are 2 symptoms of this bug. The first is that pinging of all elements (TCP/TLS/UDP) will be delayed. Therefore, their status may not be accurately reflected by the show server-group status command. The second is that committing a configuration can cause the CLI to hang for several minutes.

Conditions   Invalid or down TCP elements are listed in server-group configs.

Workaround   Only use UDP or TLS elements in server-group configurations. 

CSCsx10996 CUSP DNS SRV based call routing does not work after CUSP reboot.

Symptom    CUSP DNS SRV based call routing does not work after rebooting CUSP.

Workaround   There are two workarounds. The first is to toggle off, then on the sip dns-srv command. The second is to configure route tables with server-group based routing. 

CSCsx18654 SIP messages originated from wrong Source Interface when SRV is on.

Symptom    When multiple IPs are configured on CUSP, SIP messages source from wrong source ip.

Conditions   CUSP is configured with multiple ip interfaces. 

CSCsx38761 CUSP issue with using SRV entry that points to a device on a NAT 
network.

Symptom    When trying to make a call to the SRV defined device, CUSP cannot establish a connection and issues a 502 message to the calling device.

Conditions   This problem only occurs if the network is of type NAT.

Workaround   Use a different network type, standard, for example. 

CSCsx48124 CUSP is not handling maddr parameter in the request-uri properly.

Symptom    The maddr parameter in the request-uri is not handled properly.

Conditions   CUSP fails to remove the maddr parameter if it is pointing to CUSP on incoming requests. CUSP fails to forward the message based on the maddr address on outgoing requests. 

CSCsx62364 CUSP: Call (INVITE) from 3rd-party IP PBX is not accepted (404 No 
algor).

Symptom    Invites from the Avaya PBX are rejected with a 404 "no matching algorithm found" message.

Conditions   An Avaya PBX is used.

Workaround   Use a different model PBX. 

CSCsx65522 Update on User Portion of Request-URI fails.

Symptom    Normalization on user portion of request-uri fails, NullPointerException is thrown during normalization operation. (This can be seen by looking at the trace.log file)

Conditions   The user portion of the request-uri is empty.

Workaround   Normalize the entire request-uri to add/update the user portion.

Related Documentation

For Cisco Unified SIP Proxy documentation and configuration white papers, see:

http://cisco.com/en/US/products/ps10140/tsd_products_support_model_home.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

This document is to be used in conjunction with the documents listed in the "Related Documentation" section.

CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0812R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2009, Cisco Systems, Inc. All rights reserved.