Table Of Contents
Service Parameters
Adding a New Service on a Server
Deleting a Service From a Server
Adding a New Service Parameter
Updating a Service Parameter
Deleting a Service Parameter
Service Parameters
Service Parameters for Cisco CallManager Release 3.0 allows you to configure different services on selected servers. You can insert and delete services on a selected server, as well as insert, modify, and delete the service parameters for those services.
The Service Parameters application also provides the following:
•
A list of configured servers in the system
•A list of all configured services on a selected server
Caution Some changes to service parameters may cause system failure. We recommend you do not make any changes to service parameters unless you fully understand the feature that you are changing, or unless the changes are specified by the Cisco Technical Assistance Center (TAC). Read the
"Understanding Service Parameters" section for more detailed service parameter information.
Additional Information
The following list contains additional information related to this section:
•Understanding Service Parameters
Related Procedures
The following list contains procedures related to Service Parameters:
•Adding a New Service on a Server
•Deleting a Service From a Server
•Adding a New Service Parameter
•Updating a Service Parameter
•Deleting a Service Parameter
Adding a New Service on a Server
This section describes how to add a new service on a server.
Before You Begin
The following prerequisite must be met before proceeding with the steps:
•Servers must be configured
Procedure
Step 1 Open Cisco CallManager Administration.
Step 2 Click Service > Service Parameters.
Step 3 Select a pre-configured server from the list of configured servers on the left side of the page. The page refreshes to the server you selected, showing the services already configured on that server.
Step 4 Click New. The page refreshes again.
Step 5 Select a service type to configure on this server from the Service Type drop-down menu.
Step 6 Click Insert to configure the service type. A status message prompts you to wait.
The system loads the service type you selected.
Additional Information
The following list contains additional information related to this procedure:
•Service Parameters
•Understanding Service Parameters
Related Procedures
The following list contains other related procedures:
•Deleting a Service From a Server
•Adding a New Service Parameter
•Updating a Service Parameter
•Deleting a Service Parameter
Deleting a Service From a Server
This section describes how to delete service from a server.
Before You Begin
The following prerequisite must be met before proceeding with the steps. See the "Server" section.
•Servers must be configured
•Service must be present
Procedure
Step 1 Open Cisco CallManager Administration.
Step 2 Click Service > Service Parameters.
Step 3 Select the pre-configured server from which you want to delete a service, from the list of configured servers on the left side of the page. The page refreshes to the server you selected, showing the services already configured on that server.
Step 4 Select the configured service you want to delete. The page refreshes again.
Step 5 Click Delete Service. A message displays stating that you are about to permanently delete this service and that the action cannot be undone.
Step 6 Click OK to continue or Cancel to cancel the deletion.
The service type no longer appears in the drop-down list.
Additional Information
The following list contains additional information related to this procedure:
•Service Parameters
•Understanding Service Parameters
Related Procedures
The following list contains other related procedures:
•Adding a New Service on a Server
•Adding a New Service Parameter
•Updating a Service Parameter
•Deleting a Service Parameter
Adding a New Service Parameter
This section describes how to add a new service parameter.
Before You Begin
The following prerequisites must be met before proceeding with the steps. See the "Server" section.
•Servers must be configured
•Service must be configured
Caution Some changes to service parameters may cause system failure. We recommend you do not make any changes to service parameters unless you fully understand the feature that you are changing, or unless the changes are specified by the Cisco Technical Assistance Center (TAC). Please refer to the
"Understanding Service Parameters" section for more information about service parameters.
Procedure
Step 1 Open Cisco CallManager Administration.
Step 2 Click Service > Service Parameters.
Step 3 Select a pre-configured server from the list of configured servers on the left side of the page. The page refreshes to the list of configured services.
Step 4 Select the service to which you want to add a new parameter. The page refreshes again
Step 5 Enter the service parameter name you want to add in the Param field.
Step 6 Enter the parameter type in the Type field.
Step 7 Enter a value in the Value field.
Step 8 Click Update. A status message prompts you to wait. The page refreshes and the status message displays results.
The service parameter you added should appear in the list of configured service parameters.
Note If you want to use default settings, click Default. A message displays stating that you are about to permanently delete all the previous settings and replace them with the default settings. Click OK if you wish to use the default settings or Cancel to cancel the operation.
Additional Information
The following list contains additional information related to this procedure:
•Service Parameters
•Understanding Service Parameters
Related Procedures
The following list contains other related procedures:
•Adding a New Service on a Server
•Deleting a Service From a Server
•Updating a Service Parameter
•Deleting a Service Parameter
Updating a Service Parameter
This section describes how to update a service parameter.
Before You Begin
The following prerequisites must be met before proceeding with the steps. See the "Server" section for more information.
•Servers must be configured
•Service must be configured
Caution Some changes to service parameters may cause system failure. We recommend you do not make any changes to service parameters unless you fully understand the feature that you are changing, or unless the changes are specified by the Cisco Technical Assistance Center (TAC). Please refer to the
"Understanding Service Parameters" section for more information about service parameters.
Procedure
Step 1 Click Service > Service Parameters.
Step 2 Select a pre-configured server from the list of configured servers on the left side of the page. The page refreshes to the list of configured services.
Step 3 Select the service to which you want to update a parameter. The page refreshes again.
Step 4 Select the parameter you want to update from the list of configured service parameters.
Note Refer to the "Understanding Service Parameters" section for more information, before updating service parameters.
Step 5 Make the desired changes to the parameter, using the Param, Type and Value fields.
Note A service parameter type can only be changed if added. Default value types cannot be changed.
Step 6 Click Update. A status message prompts you to wait. The page refreshes and the status message displays results.
The service parameter should be updated with your changes.
Note If you want to use default settings, click Default. A message displays stating that you are about to permanently delete all the previous settings and replace them with the default settings. Click OK if you wish to use the default settings or Cancel to cancel the operation.
Additional Information
The following list contains additional information related to this procedure:
•Service Parameters
•Understanding Service Parameters
Related Procedures
The following list contains other related procedures:
•Adding a New Service on a Server
•Deleting a Service From a Server
•Adding a New Service Parameter
•Deleting a Service Parameter
Deleting a Service Parameter
This section describes how to delete a service parameter.
Before You Begin
The following prerequisites must be met before proceeding with the steps. See the "Server" section, and the "Understanding Service Parameters" section section for more information.
•Servers must be configured
•Service must be configured
Caution Some changes to service parameters may cause system failure. We recommend you do not make any changes to service parameters unless you fully understand the feature that you are changing, or unless the changes are specified by the Cisco Technical Assistance Center (TAC). Please refer to the
"Understanding Service Parameters" section for more information about service parameters.
Procedure
Step 1 Open Cisco CallManager Administration.
Step 2 Click Service > Service Parameters.
Step 3 Select a pre-configured server from the list of configured servers on the left side of the page. The page refreshes to the list of configured services.
Step 4 Select the service parameter you want to delete.
Step 5 Click Delete. A message displays stating that you are about to permanently delete this parameter, and that this action cannot be undone.
Step 6 Click OK to continue or Cancel to cancel the deletion.
A status message prompts you to wait. The page refreshes and the status message displays results. The service parameter should have been deleted and should no longer appear in the list of configured service parameters.
Note If you want to use default settings, click Default. A message displays stating that you are about to permanently delete all the previous settings and replace them with the default settings. Click OK if you wish to use the default settings or Cancel to cancel the operation.
Additional Information
The following list contains additional information related to this procedure:
•Service Parameters
•Understanding Service Parameters
Related Procedures
The following list contains other related procedures:
•Adding a New Service on a Server
•Deleting a Service From a Server
•Adding a New Service Parameter
•Updating a Service Parameter
Feedback
