Table Of Contents
Voice Configuration Menu Codes
Voice Configuration Menu Codes
This section contains a quick-reference list of the voice configuration menu options for the Cisco ATA. For information on using the voice configuration menu codes, see "Configuring the Cisco ATA for MGCP."
This section contains the following tables:
•Cisco ATA Voice Menu Codes—Information Options
•Cisco ATA Voice Menu Codes—Configuration Parameters
•Cisco ATA Voice Menu Codes—Software Upgrade
Note # .
Note Cisco ATA refers to both the Cisco ATA 186 and the Cisco ATA 188, unless otherwise stated.
Table A-1 lists codes to return basic Cisco ATA information.
Table A-1 Cisco ATA Voice Menu Codes—Information Options
Option
Voice Menu Code
Description
Build information
123123
Build date of the Cisco ATA software
Review IP address
21
Returns IP address of the Cisco ATA
Review MAC address
24
Returns MAC address of the Cisco ATA
Review network route IP address
22
Returns IP address of the network route
Review subnet mask
23
Returns subnet mask of the network route
Version number
123
Returns version number of the Cisco ATA software
Table A-2 lists configuration codes. For additional information about these parameters, see ""Parameters and Defaults."
Table A-2 Cisco ATA Voice Menu Codes—Configuration Parameters
Option
Voice Menu Code
Description
Audio mode
312
Allows finer control of the audio component to suit certain user applications
Caller ID method
316
Specifies the signal format when generating the Caller ID format to use
CA0orCM0
5
Primary call agent
CA1orCM1
6
Alternate call agent
Connection mode
311
Controls the connection mode of the call signaling protocol
Dynamic Host Configuration Protocol (DHCP)
20
Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network
DNS 1 IP
916
IP address of the primary DNS server
DNS 2 IP
917
IP address of the secondary DNS server
Domain
931
Determines how the domain name portion of the endpoint identifier is constructed.
EPID0or SID0
46
MGCP endpoint ID for line 0 (Phone 1 port)
EPID1or SID1
47
MGCP endpoint ID for line 1 (Phone 2 port)
Static IP address
1
IP address of the Cisco ATA
LBR codec
300
Low-bit-rate codec selection
Media port
202
Specifies which base port the Cisco ATA uses to receive RTP media streams.
MGCPPort
201
The listening port for MGCP messages on the Cisco ATA
MGCP protocol
38
Selects the signaling protocol
MGCPVer
206
MGCP version string
NPrintf address
81
IP address of a host to which all Cisco ATA debug messages are sent
NumTXFrames
35
Sets the default RTP packet size
OpFlags
323
Enables operational features
PrfCodec
36
Specifies the preferred default codec
RetxIntv
203
First retransmission interval
RetxLim
205
Maximum number or times the Cisco ATA retransmits commands
Set password
7387277
Configuration interface password
Signal timers
318
Timeout values controlling the starting or stopping of a signaling event
Static network route address
2
Network router address
Static subnet mask
10
Specifies the subnet mask for the Cisco ATA.
TFTP URL
905
IP address of the TFTP server when TFTP configuration is used
UDP ToS bits
255
Determines the precedence and delay of UDP IP packets
Use TFTP
305
Enables TFTP as configuration method
VLANSetting
324
Enables VLAN ID and 802.1Q priority for Voice Audio IP packet and Signaling IP packet
Table A-3 lists codes used in the software upgrade process. For information about these codes, see "Upgrading the Cisco ATA Signaling Image."
Table A-3 Cisco ATA Voice Menu Codes—Software Upgrade
Option
Voice Menu Code
Description
Upgrade software
100
Used in the software process to enter the IP address of the PC
Upgrade language to English
101
Changes or upgrades the voice prompt language to English when upgrading software
Feedback
Cisco ATA Voice Menu Codes—Information Options
