Cisco UCS Manager CLI Configuration Guide, Release 2.1
Configuring Storage-Related Policies
Download this chapter
Configuring Storage-Related PoliciesConfiguring Storage-Related Policies
Download the complete book
Cisco UCS Manager CLI Configuration Guide, Release 2.1Cisco UCS Manager CLI Configuration Guide, Release 2.1 (PDF - 9 MB)
 Feedback

Contents

Configuring Storage-Related Policies

This chapter includes the following sections:

Configuring vHBA Templates

vHBA Template

This template is a policy that defines how a vHBA on a server connects to the SAN. It is also referred to as a vHBA SAN connectivity template.

You need to include this policy in a service profile for it to take effect.

Configuring a vHBA Template

Procedure
     Command or ActionPurpose
    Step 1UCS-A# scope org org-name  

    Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name .

     
    Step 2UCS-A /org # create vhba-templ vhba-templ-name [fabric {a | b}] [fc-if vsan-name]  

    Creates a vHBA template and enters organization vHBA template mode.

     
    Step 3UCS-A /org/vhba-templ # set descr description   (Optional)

    Provides a description for the vHBA template.

     
    Step 4UCS-A /org/vhba-templ # set fabric {a | b}   (Optional)

    Specifies the fabric to use for the vHBA. If you did not specify the fabric when creating the vHBA template in Step 2, then you have the option to specify it with this command.

     
    Step 5UCS-A /org/vhba-templ # set fc-if vsan-name   (Optional)

    Specifies the Fibre Channel interface (named VSAN) to use for the vHBA template. If you did not specify the Fibre Channel interface when creating the vHBA template in Step 2, you have the option to specify it with this command.

     
    Step 6UCS-A /org/vhba-templ # set max-field-size size-num  

    Specifies the maximum size of the Fibre Channel frame payload (in bytes) that the vHBA supports.

     
    Step 7UCS-A /org/vhba-templ # set pin-group group-name  

    Specifies the pin group to use for the vHBA template.

     
    Step 8UCS-A /org/vhba-templ # set qos-policy mac-pool-name  

    Specifies the QoS policy to use for the vHBA template.

     
    Step 9UCS-A /org/vhba-templ # set stats-policy policy-name  

    Specifies the server and server component statistics threshold policy to use for the vHBA template.

     
    Step 10UCS-A /org/vhba-templ # set type {initial-template | updating-template}  

    Specifies the vHBA template update type. If you do not want vHBA instances created from this template to be automatically updated when the template is updated, use theinitial-template keyword; otherwise, use the updating-template keyword to ensure that all vHBA instances are updated when the vHBA template is updated.

     
    Step 11UCS-A /org/vhba-templ # set wwpn-pool pool-name  

    Specifies the WWPN pool to use for the vHBA template.

     
    Step 12UCS-A /org/vhba-templ # commit-buffer  

    Commits the transaction to the system configuration.

     

    The following example configures a vHBA template and commits the transaction: 

    UCS-A# scope org /
UCS-A /org* # create vhba template VhbaTempFoo
UCS-A /org/vhba-templ* # set descr "This is a vHBA template example."
UCS-A /org/vhba-templ* # set fabric a
UCS-A /org/vhba-templ* # set fc-if accounting
UCS-A /org/vhba-templ* # set max-field-size 2112
UCS-A /org/vhba-templ* # set pin-group FcPinGroup12
UCS-A /org/vhba-templ* # set qos-policy policy34foo
UCS-A /org/vhba-templ* # set stats-policy ServStatsPolicy
UCS-A /org/vhba-templ* # set type updating-template
UCS-A /org/vhba-templ* # set wwpn-pool SanPool7
UCS-A /org/vhba-templ* # commit-buffer
UCS-A /org/vhba-templ #

    Deleting a vHBA Template

    Procedure
       Command or ActionPurpose
      Step 1UCS-A# scope org org-name  

      Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name .

       
      Step 2UCS-A /org # delete vhba-templ vhba-templ-name  

      Deletes the specified vHBA template.

       
      Step 3UCS-A /org # commit-buffer  

      Commits the transaction to the system configuration.

       

      The following example deletes the vHBA template named VhbaTempFoo and commits the transaction: 

      UCS-A# scope org /
UCS-A /org # delete vhba template VhbaTempFoo
UCS-A /org* # commit-buffer
UCS-A /org #

      Configuring Fibre Channel Adapter Policies

      Ethernet and Fibre Channel Adapter Policies

      These policies govern the host-side behavior of the adapter, including how the adapter handles traffic. For example, you can use these policies to change default settings for the following:

      • Queues
      • Interrupt handling
      • Performance enhancement
      • RSS hash
      • Failover in an cluster configuration with two fabric interconnects

      Note

      For Fibre Channel adapter policies, the values displayed by Cisco UCS Manager may not match those displayed by applications such as QLogic SANsurfer. For example, the following values may result in an apparent mismatch between SANsurfer and Cisco UCS Manager:

      • Max LUNs Per Target—SANsurfer has a maximum of 256 LUNs and does not display more than that number. Cisco UCS Manager supports a higher maximum number of LUNs.
      • Link Down Timeout—In SANsurfer, you configure the timeout threshold for link down in seconds. In Cisco UCS Manager, you configure this value in milliseconds. Therefore, a value of 5500 ms in Cisco UCS Manager displays as 5s in SANsurfer.
      • Max Data Field Size—SANsurfer has allowed values of 512, 1024, and 2048. Cisco UCS Manager allows you to set values of any size. Therefore, a value of 900 in Cisco UCS Manager displays as 512 in SANsurfer.

      Operating System Specific Adapter Policies

      By default, Cisco UCS provides a set of Ethernet adapter policies and Fibre Channel adapter policies. These policies include the recommended settings for each supported server operating system. Operating systems are sensitive to the settings in these policies. Storage vendors typically require non-default adapter settings. You can find the details of these required settings on the support list provided by those vendors.

      Important:

      We recommend that you use the values in these policies for the applicable operating system. Do not modify any of the values in the default policies unless directed to do so by Cisco Technical Support.

      However, if you are creating an Ethernet adapter policy for a Windows OS (instead of using the default Windows adapter policy), you must use the following formulas to calculate values that work with Windows:

      • Completion Queues = Transmit Queues + Receive Queues
      • Interrupt Count = (Completion Queues + 2) rounded up to nearest power of 2

      For example, if Transmit Queues = 1 and Receive Queues = 8 then:

      • Completion Queues = 1 + 8 = 9
      • Interrupt Count = (9 + 2) rounded up to the nearest power of 2 = 16

      Configuring a Fibre Channel Adapter Policy

      Procedure
         Command or ActionPurpose
        Step 1UCS-A# scope org org-name  

        Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name .

         
        Step 2UCS-A /org # create fc-policy policy-name  

        Creates the specified Fibre Channel adapter policy and enters organization Fibre Channel policy mode.

         
        Step 3UCS-A /org/fc-policy # set descr description   (Optional)

        Provides a description for the policy.

        Note   

        If your description includes spaces, special characters, or punctuation, you must begin and end your description with quotation marks. The quotation marks will not appear in the description field of any show command output.

         
        Step 4UCS-A /org/fc-policy # set error-recovery {fcp-error-recovery {disabled | enabled} | link-down-timeout timeout-msec | port-down-io-retry-count retry-count | port-down-timeout timeout-msec}   (Optional)

        Configures the Fibre Channel error recovery.

         
        Step 5UCS-A /org/fc-policy # set interrupt mode {intx | msi | msi-x}}   (Optional)

        Configures the driver interrupt mode.

         
        Step 6UCS-A /org/fc-policy # set port {io-throttle-count throttle-count | max-luns max-num}   (Optional)

        Configures the Fibre Channel port.

         
        Step 7UCS-A /org/fc-policy # set port-f-logi {retries retry-count | timeout timeout-msec}   (Optional)

        Configures the Fibre Channel port fabric login (FLOGI).

         
        Step 8UCS-A /org/fc-policy # set port-p-logi {retries retry-count | timeout timeout-msec}   (Optional)

        Configures the Fibre Channel port-to-port login (PLOGI).

         
        Step 9UCS-A /org/fc-policy # set recv-queue {count count | ring-size size-num}   (Optional)

        Configures the Fibre Channel receive queue.

         
        Step 10UCS-A /org/fc-policy # set scsi-io {count count | ring-size size-num}   (Optional)

        Configures the Fibre Channel SCSI I/O.

         
        Step 11UCS-A /org/fc-policy # set trans-queue ring-size size-num}   (Optional)

        Configures the Fibre Channel transmit queue.

         
        Step 12UCS-A /org/fc-policy # commit-buffer  

        Commits the transaction to the system configuration.

         

        The following example configures a Fibre Channel adapter policy and commits the transaction: 

        UCS-A# scope org /
UCS-A /org* # create fc-policy FcPolicy42
UCS-A /org/fc-policy* # set descr "This is a Fibre Channel adapter policy example."
UCS-A /org/fc-policy* # set error-recovery error-detect-timeout 2500
UCS-A /org/fc-policy* # set port max-luns 4
UCS-A /org/fc-policy* # set port-f-logi retries 250
UCS-A /org/fc-policy* # set port-p-logi timeout 5000
UCS-A /org/fc-policy* # set recv-queue count 1
UCS-A /org/fc-policy* # set scsi-io ring-size 256
UCS-A /org/fc-policy* # set trans-queue ring-size 256
UCS-A /org/fc-policy* # commit-buffer
UCS-A /org/fc-policy #

        Deleting a Fibre Channel Adapter Policy

        Procedure
           Command or ActionPurpose
          Step 1UCS-A# scope org org-name  

          Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name .

           
          Step 2UCS-A /org # delete fc-policy policy-name  

          Deletes the specified Fibre Channel adapter policy.

           
          Step 3UCS-A /org # commit-buffer  

          Commits the transaction to the system configuration.

           

          The following example deletes the Fibre Channel adapter policy named FcPolicy42 and commits the transaction: 

          UCS-A# scope org /
UCS-A /org # delete fc-policy FcPolicy42
UCS-A /org* # commit-buffer
UCS-A /org #

          Configuring the Default vHBA Behavior Policy

          Default vHBA Behavior Policy

          Default vHBA behavior policy allow you to configure how vHBAs are created for a service profile. You can choose to create vHBAs manually, or you can allow them to be created automatically.

          You can configure the default vHBA behavior policy to define how vHBAs are created. This can be one of the following:

          • None—Cisco UCS Manager does not create default vHBAs for a service profile. All vHBAs must be explicitly created.
          • HW Inherit—If a service profile requires vHBAs and none have been explicitly defined, Cisco UCS Manager creates the required vHBAs based on the adapter installed in the server associated with the service profile.

          Note

          If you do not specify a default behavior policy for vHBAs, none is used by default.

          Configuring a Default vHBA Behavior Policy

          Procedure
             Command or ActionPurpose
            Step 1UCS-A# scope org / 

            Enters the root organization mode.

             
            Step 2UCS-A/org # scope vhba-beh-policy 

            Enters default vHBA behavior policy mode.

             
            Step 3UCS-A/org/vhba-beh-policy # set action {hw-inherit [template_name name] | none} 

            Specifies the default vHBA behavior policy. This can be one of the following:

            • hw-inherit—If a service profile requires vHBAs and none have been explicitly defined, Cisco UCS Manager creates the required vHBAs based on the adapter installed in the server associated with the service profile. If you specify hw-inherit, you can also specify a vHBA template to create the vHBAs.
            • none—Cisco UCS Manager does not create default vHBAs for a service profile. All vHBAs must be explicitly created.
             
            Step 4UCS-A/org/vhba-beh-policy # commit-buffer 

            Commits the transaction to the system configuration.

             

            This example shows how to set the default vHBA behavior policy to hw-inherit. 

            UCS-A # scope org /
UCS-A/org # scope vhba-beh-policy
UCS-A/org/vhba-beh-policy # set action hw-inherit
UCS-A/org/vhba-beh-policy* # commit-buffer
UCS-A/org/vhba-beh-policy #

            Configuring SAN Connectivity Policies

            LAN and SAN Connectivity Policies

            Connectivity policies determine the connections and the network communication resources between the server and the LAN or SAN on the network. These policies use pools to assign MAC addresses, WWNs, and WWPNs to servers and to identify the vNICs and vHBAs that the servers use to communicate with the network.


            Note

            We do not recommend that you use static IDs in connectivity policies, because these policies are included in service profiles and service profile templates and can be, used to configure multiple servers.

            Privileges Required for LAN and SAN Connectivity Policies

            Connectivity policies enable users without network or storage privileges to create and modify service profiles and service profile templates with network and storage connections. However, users must have the appropriate network and storage privileges to create connectivity policies.

            Privileges Required to Create Connectivity Policies

            Connectivity policies require the same privileges as other network and storage configurations. For example, you must have at least one of the following privileges to create connectivity policies:

            • admin—Can create LAN and SAN connectivity policies
            • ls-server—Can create LAN and SAN connectivity policies
            • ls-network—Can create LAN connectivity policies
            • ls-storage—Can create SAN connectivity policies

            Privileges Required to Add Connectivity Policies to Service Profiles

            After the connectivity policies have been created, a user with ls-compute privileges can include them in a service profile or service profile template. However, a user with only ls-compute privileges cannot create connectivity policies.

            Interactions between Service Profiles and Connectivity Policies

            You can configure the LAN and SAN connectivity for a service profile through either of the following methods:

            • LAN and SAN connectivity policies that are referenced in the service profile
            • Local vNICs and vHBAs that are created in the service profile
            • Local vNICs and a SAN connectivity policy
            • Local vHBAs and a LAN connectivity policy

            Cisco UCS maintains mutual exclusivity between connectivity policies and local vNIC and vHBA configuration in the service profile. You cannot have a combination of connectivity policies and locally created vNICs or vHBAs. When you include a LAN connectivity policy in a service profile, all existing vNIC configuration is erased, and when you include a SAN connectivity policy, all existing vHBA configuration in that service profile is erased.

            Creating a SAN Connectivity Policy

            Procedure
               Command or ActionPurpose
              Step 1UCS-A# scope org org-name 

              Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

               
              Step 2UCS-A /org # create san-connectivity-policy policy-name  

              Creates the specified SAN connectivity policy, and enters organization network control policy mode.

              This name can be between 1 and 16 alphanumeric characters. You cannot use spaces or any special characters other than - (hyphen), _ (underscore), : (colon), and . (period), and you cannot change this name after the object has been saved.

               
              Step 3UCS-A /org/lan-connectivity-policy # set descr policy-name   (Optional)

              Adds a description to the policy. We recommend that you include information about where and how the policy should be used.

              Enter up to 256 characters. You can use any characters or spaces except ` (accent mark), \ (backslash), ^ (carat), " (double quote), = (equal sign), > (greater than), < (less than), or ' (single quote).

               
              Step 4UCS-A /org/service-profile # set identity {dynamic-uuid {uuid | derived} | dynamic-wwnn {wwnn | derived} | uuid-pool pool-name | wwnn-pool pool-name}  

              Specifies how the server acquires a UUID or WWNN. You can do one of the following:

              • Create a unique UUID in the form nnnnnnnn-nnnn-nnnn-nnnnnnnnnnnn
              • Derive the UUID from the one burned into the hardware at manufacture
              • Use a UUID pool
              • Create a unique WWNN in the form hh : hh : hh : hh : hh : hh : hh : hh
              • Derive the WWNN from one burned into the hardware at manufacture
              • Use a WWNN pool
               
              Step 5UCS-A /org/lan-connectivity-policy # commit-buffer  

              Commits the transaction to the system configuration.

               

              The following example shows how to create a SAN connectivity policy named SanConnect242 and commit the transaction:

              UCS-A# scope org /
UCS-A /org* # create san-connectivity-policy SanConnect242
UCS-A /org/san-connectivity-policy* # set descr "SAN connectivity policy"
UCS-A /org/san-connectivity-policy* # set identity wwnn-pool SanPool7
UCS-A /org/san-connectivity-policy* # commit-buffer
UCS-A /org/san-connectivity-policy #
              What to Do Next

              Add one or more vHBAs and/or initiator groups to this SAN connectivity policy.

              Creating a vHBA for a SAN Connectivity Policy

              If you are continuing from Creating a SAN Connectivity Policy, begin this procedure at Step 3.

              Procedure
                 Command or ActionPurpose
                Step 1UCS-A# scope org org-name 

                Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

                 
                Step 2UCS-A /org # scope san-connectivity-policy policy-name  

                Enters SAN connectivity policy mode for the specified SAN connectivity policy.

                 
                Step 3UCS-A /org/san-connectivity-policy # create vhba vhba-name [fabric {a | b}] [fc-if fc-if-name]  

                Creates a vHBA for the specified SAN connectivity policy and enters vHBA mode.

                This name can be between 1 and 16 alphanumeric characters. You cannot use spaces or any special characters other than - (hyphen), _ (underscore), : (colon), and . (period), and you cannot change this name after the object has been saved.

                 
                Step 4UCS-A /org/san-connectivity-policy/vhba # set adapter-policy policy-name  

                Specifies the adapter policy to use for the vHBA.

                 
                Step 5UCS-A /org/san-connectivity-policy/vhba # set identity {dynamic-wwpn {wwpn | derived} | wwpn-pool wwn-pool-name}  

                Specifies the WWPN for the vHBA.

                You can set the storage identity using one of the following options:

                • Create a unique WWPN in the form hh:hh:hh:hh:hh:hh:hh:hh. You can specify a WWPN in the range from 20:00:00:00:00:00:00:00 to 20:FF:FF:FF:FF:FF:FF:FF or from 50:00:00:00:00:00:00:00 to 5F:FF:FF:FF:FF:FF:FF:FF. If you want the WWPN to be compatible with Cisco MDS Fibre Channel switches, use the WWPN template 20:00:00:25:B5:XX:XX:XX.
                • Derive the WWPN from one burned into the hardware at manufacture.
                • Assign a WWPN from a WWN pool.
                 
                Step 6UCS-A /org/san-connectivity-policy/vhba # set max-field-size size-num  

                Specifies the maximum size of the Fibre Channel frame payload (in bytes) that the vHBA supports.

                Enter an integer between 256 and 2112. The default is 2048.

                 
                Step 7UCS-A /org/san-connectivity-policy/vhba # set order {order-num | unspecified}  

                Specifies the PCI scan order for the vHBA.

                 
                Step 8UCS-A /org/san-connectivity-policy/vhba # set pers-bind {disabled | enabled}  

                Disables or enables persistent binding to Fibre Channel targets.

                 
                Step 9UCS-A /org/san-connectivity-policy/vhba # set pin-group group-name  

                Specifies the SAN pin group to use for the vHBA.

                 
                Step 10UCS-A /org/san-connectivity-policy/vhba # set qos-policy policy-name  

                Specifies the QoS policy to use for the vHBA.

                 
                Step 11UCS-A /org/san-connectivity-policy/vhba # set stats-policy policy-name  

                Specifies the statistics threshold policy to use for the vHBA.

                 
                Step 12UCS-A /org/san-connectivity-policy/vhba # set template-name policy-name  

                Specifies the vHBA template to use for the vHBA. If you choose to use a vHBA template for the vHBA, you must still complete all of the configuration not included in the vHBA template, including Steps 4, 7, and 8.

                 
                Step 13UCS-A /org/san-connectivity-policy/vhba # set vcon {1 | 2 | 3 | 4 | any}  

                Assigns the vHBA to one or all virtual network interface connections.

                 
                Step 14UCS-A /org/san-connectivity-policy/vhba # commit-buffer  

                Commits the transaction to the system configuration.

                 

                The following example shows how to configure a vHBA for a SAN connectivity policy named SanConnect242 and commit the transaction:

                UCS-A# scope org /
UCS-A /org* # scope san-connectivity-policy SanConnect242
UCS-A /org/san-connectivity-policy* # create vhba vhba3 fabric a
UCS-A /org/san-connectivity-policy/vhba* # set adapter-policy AdaptPol2
UCS-A /org/san-connectivity-policy/vhba* # set identity wwpn-pool SanPool7
UCS-A /org/san-connectivity-policy/vhba* # set max-field-size 2112
UCS-A /org/san-connectivity-policy/vhba* # set order 0
UCS-A /org/san-connectivity-policy/vhba* # set pers-bind enabled
UCS-A /org/san-connectivity-policy/vhba* # set pin-group FcPinGroup12
UCS-A /org/san-connectivity-policy/vhba* # set qos-policy QosPol5
UCS-A /org/san-connectivity-policy/vhba* # set stats-policy StatsPol2
UCS-A /org/san-connectivity-policy/vhba* # set template-name SanConnPol3
UCS-A /org/san-connectivity-policy/vhba* # set vcon any
UCS-A /org/san-connectivity-policy/vhba* # commit-buffer
UCS-A /org/san-connectivity-policy/vhba #
                What to Do Next

                If desired, add another vHBA or an initiator group to the SAN connectivity policy. If not, include the policy in a service profile or service profile template.

                Deleting a vHBA from a SAN Connectivity Policy

                Procedure
                   Command or ActionPurpose
                  Step 1UCS-A# scope org org-name 

                  Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

                   
                  Step 2UCS-A /org # scope san-connectivity-policy policy-name  

                  Enters SAN connectivity policy mode for the specified SAN connectivity policy.

                   
                  Step 3UCS-A /org/san-connectivity-policy # delete vHBA vhba-name 

                  Deletes the specified vHBA from the SAN connectivity policy.

                   
                  Step 4UCS-A /org/san-connectivity-policy # commit-buffer  

                  Commits the transaction to the system configuration.

                   

                  The following example shows how to delete a vHBA named vHBA3 from a SAN connectivity policy named SanConnect242 and commit the transaction:

                  UCS-A# scope org /
UCS-A /org # scope san-connectivity-policy SanConnect242
UCS-A /org/san-connectivity-policy # delete vHBA vHBA3
UCS-A /org/san-connectivity-policy* # commit-buffer
UCS-A /org/san-connectivity-policy #

                  Creating an Initiator Group for a SAN Connectivity Policy

                  If you are continuing from Creating a SAN Connectivity Policy, begin this procedure at Step 3.

                  Procedure
                     Command or ActionPurpose
                    Step 1UCS-A# scope org org-name 

                    Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

                     
                    Step 2UCS-A /org # scope san-connectivity-policy policy-name  

                    Enters SAN connectivity policy mode for the specified SAN connectivity policy.

                     
                    Step 3UCS-A /org/san-connectivity-policy # create initiator-group group-name fc 

                    Creates the specified initiator group for Fibre Channel zoning and enters initiator group mode.

                    This name can be between 1 and 16 alphanumeric characters. You cannot use spaces or any special characters other than - (hyphen), _ (underscore), : (colon), and . (period), and you cannot change this name after the object has been saved.

                     
                    Step 4UCS-A /org/san-connectivity-policy/initiator-group # create initiator vhba-name  

                    Creates the specified vHBA initiator in the initiator group.

                    If desired, repeat this step to add a second vHBA initiator to the group.

                     
                    Step 5UCS-A /org/san-connectivity-policy/initiator-group # set storage-connection-policy policy-name  

                    Associates the specified storage connection policy with the SAN connectivity policy.

                    Note   

                    This step assumes that you want to associate an existing storage connection policy to associate with the SAN connectivity policy. If you do, continue with Step 10. If you want to create a local storage definition for this policy instead, continue with Step 6.

                     
                    Step 6UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def # create storage-target wwpn  

                    Creates a storage target endpoint with the specified WWPN, and enters storage target mode.

                     
                    Step 7UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def/storage-target # set target-path {a | b}  

                    Specifies which fabric interconnect is used for communications with the target endpoint.

                     
                    Step 8UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def/storage-target # set target-vsan vsan  

                    Specifies which VSAN is used for communications with the target endpoint.

                     
                    Step 9UCS-A /org/san-connectivity-policy/initiator-group # commit-buffer  

                    Commits the transaction to the system configuration.

                     

                    The following example shows how to configure an initiator group named initGroupZone1 with two initiators for a a SAN connectivity policy named SanConnect242, configure a local storage connection policy definition named scPolicyZone1, and commit the transaction: 

                    UCS-A# scope org /
UCS-A /org* # scope san-connectivity-policy SanConnect242
UCS-A /org/san-connectivity-policy # create initiator-group initGroupZone1 fc
UCS-A /org/san-connectivity-policy/initiator-group* # set zoning-type sist
UCS-A /org/san-connectivity-policy/initiator-group* # create initiator vhba1
UCS-A /org/san-connectivity-policy/initiator-group* # create initiator vhba2
UCS-A /org/san-connectivity-policy/initiator-group* # create storage-connection-def scPolicyZone1
UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def* # create storage-target 
20:10:20:30:40:50:60:70
UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def/storage-target* # set 
target-path a
UCS-A /org/san-connectivity-policy/initiator-group/storage-connection-def/storage-target* # set 
target-vsan default
UCS-A /org/san-connectivity-policy/initiator-group* # commit-buffer
UCS-A /org/san-connectivity-policy/initiator-group #
                    What to Do Next

                    If desired, add another initiator group or a vHBA to the SAN connectivity policy. If not, include the policy in a service profile or service profile template.

                    Deleting an Initiator Group from a SAN Connectivity Policy

                    Procedure
                       Command or ActionPurpose
                      Step 1UCS-A# scope org org-name 

                      Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

                       
                      Step 2UCS-A /org # scope san-connectivity-policy policy-name  

                      Enters SAN connectivity policy mode for the specified SAN connectivity policy.

                       
                      Step 3UCS-A /org/san-connectivity-policy # delete initiator-group group-name 

                      Deletes the specified initiator group from the SAN connectivity policy.

                       
                      Step 4UCS-A /org/san-connectivity-policy # commit-buffer  

                      Commits the transaction to the system configuration.

                       

                      The following example shows how to delete an initiator group named initGroup3 from a SAN connectivity policy named SanConnect242 and commit the transaction:

                      UCS-A# scope org /
UCS-A /org # scope san-connectivity-policy SanConnect242
UCS-A /org/san-connectivity-policy # delete initiator-group initGroup3
UCS-A /org/san-connectivity-policy* # commit-buffer
UCS-A /org/san-connectivity-policy #

                      Deleting a SAN Connectivity Policy

                      If you delete a SAN connectivity policy that is included in a service profile, you will delete all vHBAs from that service profile and disrupt SAN data traffic for the server associated with the service profile.

                      Procedure
                         Command or ActionPurpose
                        Step 1UCS-A# scope org org-name 

                        Enters organization mode for the specified organization. To enter the root organization mode, enter / as the org-name.

                         
                        Step 2UCS-A /org # delete san-connectivity-policy policy-name  

                        Deletes the specified SAN connectivity policy.

                         
                        Step 3UCS-A /org # commit-buffer  

                        Commits the transaction to the system configuration.

                         

                        The following example shows how to delete a SAN connectivity policy named SanConnect52 from the root organization and commit the transaction: 

                        UCS-A# scope org /
UCS-A /org # delete san-connectivity-policy SanConnect52
UCS-A /org* # commit-buffer
UCS-A /org #