Cisco UCS Manager CLI Configuration Guide, Release 1.4
Managing the Chassis
Download this chapter
Managing the ChassisManaging the Chassis
Download the complete book
Cisco UCS Manager CLI Configuration Guide, Release 1.4Cisco UCS Manager CLI Configuration Guide, Release 1.4 (PDF - 7 MB)
 Feedback

Managing the Chassis

This chapter includes the following sections:

Guidelines for Removing and Decommissioning Chassis

Consider the following guidelines when deciding whether to remove or decommission a chassis using Cisco UCS Manager:

Decommissioning a Chassis

Decommissioning is performed when a chassis is physically present and connected but you want to temporarily remove it from the configuration. Because it is expected that a decommissioned chassis will be eventually recommissioned, a portion of the chassis' information is retained by Cisco UCS Manager for future use.

Removing a Chassis

Removing is performed when you physically remove a chassis from the system. Once the physical removal of the chassis is completed, the configuration for that chassis can be removed in Cisco UCS Manager.


Note

You cannot remove a chassis from Cisco UCS Manager if it is physically present and connected.

If you need to add a removed chassis back to the configuration, it must be reconnected and then rediscovered. During rediscovery Cisco UCS Manager will assign the chassis a new ID that may be different from ID that it held before.

Acknowledging a Chassis

Perform the following procedure if you increase or decrease the number of links that connect the chassis to the fabric interconnect. Acknowledging the chassis ensures that Cisco UCS Manager is aware of the change in the number of links and that traffics flows along all available links.

After you enable or disable a port on a fabric interconnect, wait for at least 1 minute before you reacknowledge the chassis. If you reacknowledge the chassis too soon, the pinning of server traffic from the chassis may not be updated with the changes to the port that you enabled or disabled.

Procedure
     Command or ActionPurpose
    Step 1UCS-A# acknowledge chassis chassis-num  

    Acknowledges the specified chassis.

     
    Step 2UCS-A# commit-buffer  

    Commits the transaction to the system configuration.

     

    The following example acknowledges chassis 2 and commits the transaction: 

    UCS-A# acknowledge chassis 2
UCS-A* # commit-buffer
UCS-A #

    Decommissioning a Chassis

    Procedure
       Command or ActionPurpose
      Step 1UCS-A# decommission chassis chassis-num  

      Decommissions the specified chassis.

       
      Step 2UCS-A# commit-buffer  

      Commits the transaction to the system configuration.

       

      The decommission may take several minutes to complete.

      The following example decommissions chassis 2 and commits the transaction:

      UCS-A# decommission chassis 2
UCS-A* # commit-buffer
UCS-A # show chassis

Chassis:
    Chassis    Overall Status           Admin State
    ---------- ------------------------ -----------
             1 Operable                 Acknowledged
             2 Accessibility Problem    Decommission
UCS-A #

      Removing a Chassis

      Before You Begin

      Physically remove the chassis before performing the following procedure.

      Procedure
         Command or ActionPurpose
        Step 1UCS-A# remove chassis chassis-num  

        Removes the specified chassis.

         
        Step 2UCS-A# commit-buffer  

        Commits the transaction to the system configuration.

         

        The removal may take several minutes to complete.

        The following example removes chassis 2 and commits the transaction:

        UCS-A# remove chassis 2
UCS-A* # commit-buffer
UCS-A #

        Recommissioning a Chassis

        This procedure returns the chassis to the configuration and applies the chassis discovery policy to the chassis. After this procedure, you can access the chassis and any servers in it.

        Before You Begin

        Collect the following information about the chassis to be recommissioned:

        • Vendor name
        • Model name
        • Serial number
        Procedure
           Command or ActionPurpose
          Step 1UCS-A# recommission chassis vendor-name model-name serial-num  

          Recommissions the specified chassis.

           
          Step 2UCS-A# commit-buffer  

          Commits the transaction to the system configuration.

           

          The following example recommissions a Cisco UCS 5108 chassis and commits the transaction:

          UCS-A# show chassis

Chassis:
    Chassis    Overall Status           Admin State
    ---------- ------------------------ -----------
             1 Accessibility Problem    Decommission

UCS-A# recommission chassis "Cisco Systems Inc" "Cisco UCS 5108" FOX1252GNNN
UCS-A* # commit-buffer
UCS-A #

          Renumbering a Chassis


          Note

          Chassis renumbering is supported in Cisco UCS Manager 1.4(2) and later releases. You cannot renumber a chassis in a prior release.

          Before You Begin

          If you are swapping IDs between chassis, you must first decommission both chassis and then wait for the chassis decommission FSM to complete before proceeding with the renumbering steps.

          Procedure
             Command or ActionPurpose
            Step 1UCS-A# show chassis inventory 

            Displays information about your chassis.

             
            Step 2Verify that the chassis inventory does not include the following: 
            • The chassis you want to renumber
            • A chassis with the number you want to use

            If either of these chassis are listed in the chassis inventory, decommission those chassis. You must wait until the decommission FSM is complete and the chassis are not listed in the chassis inventory before continuing. This might take several minutes.

            To see which chassis have been decommissioned, issue the show chassis decommissioned command.

             
            Step 3UCS-A# recommission chassis vendor-name model-name serial-num [chassis-num]  

            Recommissions and renumbers the specified chassis.

             
            Step 4UCS-A# commit-buffer  

            Commits the transaction to the system configuration.

             

            The following example decommissions two Cisco UCS 5108 chassis (chassis 7 and 8), switches their IDs, and commits the transaction:

            UCS-A# show chassis inventory

    Chassis    PID       Vendor         Serial (SN) HW Revision
    ------- --------- ---------------   ----------- -------------
          1 N20-C6508 Cisco Systems Inc FOX1252GAAA 0 
          2 N20-C6508 Cisco Systems Inc FOX1252GBBB 0 
          3 N20-C6508 Cisco Systems Inc FOX1252GCCC 0 
          4 N20-C6508 Cisco Systems Inc FOX1252GDDD 0 
          5 N20-C6508 Cisco Systems Inc FOX1252GEEE 0 
          6 N20-C6508 Cisco Systems Inc FOX1252GFFF 0
          7 N20-C6508 Cisco Systems Inc FOX1252GGGG 0
          8 N20-C6508 Cisco Systems Inc FOX1252GHHH 0 
          9 N20-C6508 Cisco Systems Inc FOX1252GIII 0 
         10 N20-C6508 Cisco Systems Inc FOX1252GJJJ 0 
         11 N20-C6508 Cisco Systems Inc FOX1252GKKK 0 
         12 N20-C6508 Cisco Systems Inc FOX1252GLLL 0 
         13 N20-C6508 Cisco Systems Inc FOX1252GMMM 0 
         14 N20-C6508 Cisco Systems Inc FOX1252GNNN 0 

UCS-A# decommission chassis "Cisco Systems Inc" "Cisco UCS 5108" FOX1252GHHH
UCS-A*# commit-buffer
UCS-A# decommission chassis "Cisco Systems Inc" "Cisco UCS 5108" FOX1252GIII
UCS-A*# commit-buffer
UCS-A# show chassis inventory

    Chassis    PID       Vendor         Serial (SN) HW Revision
    ------- --------- ---------------   ----------- -------------
          1 N20-C6508 Cisco Systems Inc FOX1252GAAA 0 
          2 N20-C6508 Cisco Systems Inc FOX1252GBBB 0 
          3 N20-C6508 Cisco Systems Inc FOX1252GCCC 0 
          4 N20-C6508 Cisco Systems Inc FOX1252GDDD 0 
          5 N20-C6508 Cisco Systems Inc FOX1252GEEE 0 
          6 N20-C6508 Cisco Systems Inc FOX1252GFFF 0
          7 N20-C6508 Cisco Systems Inc FOX1252GGGG 0
         10 N20-C6508 Cisco Systems Inc FOX1252GJJJ 0 
         11 N20-C6508 Cisco Systems Inc FOX1252GKKK 0 
         12 N20-C6508 Cisco Systems Inc FOX1252GLLL 0 
         13 N20-C6508 Cisco Systems Inc FOX1252GMMM 0 
         14 N20-C6508 Cisco Systems Inc FOX1252GNNN 0 

UCS-A# show chassis decommissioned

    Chassis    PID       Vendor         Serial (SN) HW Revision
    ------- --------- ---------------   ----------- -------------
          8 N20-C6508 Cisco Systems Inc FOX1252GHHH 0
          9 N20-C6508 Cisco Systems Inc FOX1252GIII 0 

UCS-A# recommission chassis "Cisco Systems Inc" "Cisco UCS 5108" FOX1252GHHH 9
UCS-A* # commit-buffer
UCS-A# recommission chassis "Cisco Systems Inc" "Cisco UCS 5108" FOX1252GIII 8
UCS-A* # commit-buffer
UCS-A # show chassis inventory

    Chassis    PID       Vendor         Serial (SN) HW Revision
    ------- --------- ---------------   ----------- -------------
          1 N20-C6508 Cisco Systems Inc FOX1252GAAA 0 
          2 N20-C6508 Cisco Systems Inc FOX1252GBBB 0 
          3 N20-C6508 Cisco Systems Inc FOX1252GCCC 0 
          4 N20-C6508 Cisco Systems Inc FOX1252GDDD 0 
          5 N20-C6508 Cisco Systems Inc FOX1252GEEE 0 
          6 N20-C6508 Cisco Systems Inc FOX1252GFFF 0
          7 N20-C6508 Cisco Systems Inc FOX1252GGGG 0
          8 N20-C6508 Cisco Systems Inc FOX1252GIII 0 
          9 N20-C6508 Cisco Systems Inc FOX1252GHHH 0 
         10 N20-C6508 Cisco Systems Inc FOX1252GJJJ 0 
         11 N20-C6508 Cisco Systems Inc FOX1252GKKK 0 
         12 N20-C6508 Cisco Systems Inc FOX1252GLLL 0 
         13 N20-C6508 Cisco Systems Inc FOX1252GMMM 0 
         14 N20-C6508 Cisco Systems Inc FOX1252GNNN 0

            Toggling the Locator LED

            Turning On the Locator LED for a Chassis

            Procedure
               Command or ActionPurpose
              Step 1UCS-A# scope chassis chassis-num  

              Enters chassis mode for the specified chassis.

               
              Step 2UCS-A /chassis # enable locator-led  

              Turns on the chassis locator LED.

               
              Step 3UCS-A /chassis # commit-buffer  

              Commits the transaction to the system configuration.

               

              The following example turns on the locator LED for chassis 2 and commits the transaction:

              UCS-A# scope chassis 2
UCS-A /chassis # enable locator-led
UCS-A /chassis* # commit-buffer
UCS-A /chassis #

              Turning Off the Locator LED for a Chassis

              Procedure
                 Command or ActionPurpose
                Step 1UCS-A# scope chassis chassis-num  

                Enters chassis mode for the specified chassis.

                 
                Step 2UCS-A /chassis # disable locator-led  

                Turns off the chassis locator LED.

                 
                Step 3UCS-A /chassis # commit-buffer  

                Commits the transaction to the system configuration.

                 

                The following example turns off the locator LED for chassis 2 and commits the transaction:

                UCS-A# scope chassis 2
UCS-A /chassis # disable locator-led
UCS-A /chassis* # commit-buffer
UCS-A /chassis #