Cisco UCS Manager CLI Configuration Guide, Release 1.1(1) - Managing the Servers [Cisco UCS Manager]

Contents
Managing the Servers
Booting a Server
Shutting Down a Server
Power Cycling a Server
Performing a Hard Reset on a Server
Acknowledging a Server
Removing a Server from a Chassis
Decommissioning a Server
Turning On the Locator LED for a Server
Turning Off the Locator LED for a Server
Resetting the CMOS for a Server
Resetting the BMC for a Server
Managing the Servers

This chapter includes the following sections:

Booting a Server

Shutting Down a Server

Power Cycling a Server

Performing a Hard Reset on a Server

Acknowledging a Server

Removing a Server from a Chassis

Decommissioning a Server

Turning On the Locator LED for a Server

Turning Off the Locator LED for a Server

Resetting the CMOS for a Server

Resetting the BMC for a Server
Booting a Server
Before You Begin
Associate a service profile with a server or server pool.

Procedure
Command or Action Purpose

Step 1 UCS-A# scope org org-name
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name.

Step 2 UCS-A /org # scope service-profile profile-name
Enters organization service profile mode for the specified service profile.

Step 3 UCS-A /org/service-profile # power up
Boots the server associated with the service profile.

Step 4 UCS-A /org/service-profile # commit-buffer
Commits the transaction to the system configuration.
The following example boots the server associated with the service profile named ServProf34 and commits the transaction:
UCS-A# scope org /
UCS-A /org* # scope service-profile ServProf34
UCS-A /org/service-profile* # power up
UCS-A /org/service-profile* # commit-buffer
UCS-A /org/service-profile #
Shutting Down a Server
When you use this procedure to shut down a server with an installed operating system, Cisco UCS Manager triggers the OS into a graceful shutdown sequence.

Before You Begin
Associate a service profile with a server or server pool.

Procedure
Command or Action Purpose

Step 1 UCS-A# scope org org-name
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name.

Step 2 UCS-A /org # scope service-profile profile-name
Enters organization service profile mode for the specified service profile.

Step 3 UCS-A /org/service-profile # power down
Shuts down the server associated with the service profile.

Step 4 UCS-A /org/service-profile # commit-buffer
Commits the transaction to the system configuration.
The following example shuts down the server associated with the service profile named ServProf34 and commits the transaction:
UCS-A# scope org /
UCS-A /org # scope service-profile ServProf34
UCS-A /org/service-profile # power down
UCS-A /org/service-profile* # commit-buffer
UCS-A /org/service-profile #
Power Cycling a Server
Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis server mode for the specified server.

Step 2 UCS-A /chassis/server # cycle {cycle-immediate | cycle-wait}
Power cycles the server.

Use the cycle-immediate keyword to immediately begin power cycling the server; use the cycle-wait keyword to schedule the power cycle to begin after all pending management operations have completed.

Step 3 UCS-A# commit-buffer
Commits the transaction to the system configuration.
The following example immediately power cycles server 4 in chassis 2 and commits the transaction:
UCS-A#  scope server 2/4
UCS-A /chassis/server # cycle cycle-immediate
UCS-A /chassis/server* # commit-buffer
UCS-A /chassis/server # 
Performing a Hard Reset on a Server
When you reset a server, Cisco UCS Manager sends a pulse on the reset line. You can choose to gracefully shutdown the operating system. If the operating system does not support a graceful shutdown, the server will be power cycled. The option to have Cisco UCS Manager complete all management operations before it resets the server does not guarantee that these operations will be completed before the server is reset.

Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis server mode for the specified server.

Step 2 UCS-A /chassis/server # reset {hard-reset-immediate | hard-reset-wait}
Performs a hard reset of the server.

Use the hard-reset-immediate keyword to immediately begin hard resetting the server; use the hard-reset-wait keyword to schedule the hard reset to begin after all pending management operations have completed.

Step 3 UCS-A# commit-buffer
Commits the transaction to the system configuration.
The following example performs an immediate hard reset of server 4 in chassis 2 and commits the transaction:
UCS-A#  scope server 2/4
UCS-A /chassis/server # reset hard-reset-immediate
UCS-A /chassis/server* # commit-buffer
UCS-A /chassis/server # 
Acknowledging a Server
Perform the following procedure if you need to have Cisco UCS Manager rediscover the server and all endpoints in the server. For example, you can use this procedure if a server is stuck in an unexpected state, such as the discovery state.

Procedure
Command or Action Purpose

Step 1 UCS-A# acknowledge server chassis-num / server-num
Acknowledges the specified server.

Step 2 UCS-A# commit-buffer
Commits the transaction to the system configuration.
The following example acknowledges server 4 in chassis 2 and commits the transaction:
UCS-A#  acknowledge server 2/4
UCS-A* # commit-buffer
UCS-A # 
Removing a Server from a Chassis
Before You Begin
Physically remove the server before performing the following procedure.

Procedure
Command or Action Purpose

Step 1 UCS-A# remove server chassis-num / server-num
Removes the specified server.

Step 2 UCS-A# commit-buffer
Commits the transaction to the system configuration.
The following example removes server 4 in chassis 2 and commits the transaction:
UCS-A#  remove server 2/4
UCS-A* # commit-buffer
UCS-A # 
What to Do Next

If you physically re-install the server, you must re-acknowledge the slot to have Cisco UCS Manager rediscover the server.

For more information, see Acknowledging a Server.
Decommissioning a Server
This procedure removes the server from the configuration. As long as the server physically remains in the Cisco UCS instance, Cisco UCS Manager considers the server to be decommissioned and ignores it.

Procedure
Command or Action Purpose

Step 1 UCS-A# decommission server chassis-num / server-num
Decommissions the specified server.

Step 2 UCS-A# commit-buffer
Commits the transaction to the system configuration.
The following example decommissions server 4 in chassis 2 and commits the transaction:
UCS-A# decommission server 2/4
UCS-A* # commit-buffer
UCS-A # 
Turning On the Locator LED for a Server
Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis server mode for the specified chassis.

Step 2 UCS-A /chassis/server # enable locator-led
Turns on the server locator LED.

Step 3 UCS-A /chassis/server # commit-buffer
Commits the transaction to the system configuration.
The following example turns on the locator LED for server 4 in chassis 2 and commits the transaction:
UCS-A# scope server 2/4
UCS-A /chassis/server # enable  locator-led
UCS-A /chassis/server* # commit-buffer
UCS-A /chassis/server # 
Turning Off the Locator LED for a Server
Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis mode for the specified chassis.

Step 2 UCS-A /chassis/server # disable locator-led
Turns off the server locator LED.

Step 3 UCS-A /chassis/server # commit-buffer
Commits the transaction to the system configuration.
The following example turns off the locator LED for server 4 in chassis 2 and commits the transaction:
UCS-A# scope chassis 2/4
UCS-A /chassis/server # disable  locator-led
UCS-A /chassis/server* # commit-buffer
UCS-A /chassis/server # 
Resetting the CMOS for a Server
On rare occasions, troubleshooting a server may require you to reset the CMOS. This procedure is not part of the normal maintenance of a server.

Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis server mode for the specified chassis.

Step 2 UCS-A /chassis/server # reset-cmos
Resets the CMOS for the server.

Step 3 UCS-A /chassis/server # commit-buffer
Commits the transaction to the system configuration.
The following example resets the CMOS for server 4 in chassis 2 and commits the transaction:
UCS-A# scope server 2/4
UCS-A /chassis/server # reset-cmos
UCS-A /chassis/server* # commit-buffer
UCS-A /chassis/server #  
Resetting the BMC for a Server
On rare occasions, such as an issue with the current running firmware, troubleshooting a server may require you to reset the BMC. This procedure is not part of the normal maintenance of a server. After you reset the BMC, the server boots with the running version of the firmware for that server.

Procedure
Command or Action Purpose

Step 1 UCS-A# scope server chassis-num / server-num
Enters chassis server mode for the specified chassis.

Step 2 UCS-A /chassis/server # scope bmc
Enters chassis server BMC mode

Step 3 UCS-A /chassis/server/bmc # reset
Resets the BMC for the server.

Step 4 UCS-A /chassis/server/bmc # commit-buffer
Commits the transaction to the system configuration.
The following example resets the BMC for server 4 in chassis 2 and commits the transaction:
UCS-A# scope server 2/4
UCS-A /chassis/server # scope bmc
UCS-A /chassis/server/cimc # reset
UCS-A /chassis/server/cimc* # commit-buffer
UCS-A /chassis/server/cimc #  