Contents

• Commands

• acknowledge chassis

• acknowledge fault

• acknowledge server

• acknowledge slot

• activate firmware

• activate firmware (fabric)

• add alertgroups

• add backup action

• add privilege

• associate server

• associate server-pool

• backup sel

• cd

• clear alertgroups

• clear backup action

• clear cores

• clear license

• clear sel

• clear sshkey

• cluster force primary

• cluster lead

• commit-buffer

• connect adapter

• connect bmc

• connect clp

• connect iom

• connect local-mgmt

• connect nxos

• copy

• create adapter

• create backup

• create bios-policy

• create block

• create boot-definition

• create boot-policy

• create cap-qual

• create certreq

• create chassis

• create class chassis-stats

• create class cmc-stats

• create class cpu-env-stats

• create class dimm-stats

• create class ether-error-stats

• create class ether-if-stats

• create class ether-loss-stats

• create class ethernet-port-err-stats

• create class ethernet-port-multicast-stats

• create class ethernet-port-over-under-sized-stats

• create class ethernet-port-stats

• create class ethernet-port-stats-by-size-large-packets

• create class ethernet-port-stats-by-size-small-packets

• create class ether-rx-stats

• create class ether-tx-stats

• create class fan-module-stats

• create class fan-stats

• create class fc-error-stats

• create class fc-if-event-stats

• create class fc-if-fc4-counters

• create class fc-if-frame-stats

• create class fc-port-stats

• create class fc-stats

• create class mb-power-stats

• create class mb-temp-stats

• create class memory-runtime

• create class menlo-dce-port-stats

• create class menlo-eth-error-stats

• create class menlo-eth-stats

• create class menlo-fc-error-stats

• create class menlo-fc-stats

• create class menlo-host-port-stats

• create class menlo-mcpu-error-stats

• create class menlo-mcpu-stats

• create class menlo-net-eg-stats

• create class menlo-net-in-stats

• create class menlo-q-error-stats

• create class menlo-q-stats

• create class processor-runtime

• create class psu-input-stats

• create class psu-stats

• create class system-stats

• create client

• create class vnic-stats

• create cpu

• create data-center

• create default-behavior

• create destination

• create distributed-virtual-switch

• create dns

• create dynamic-vnic-conn

• create dynamic-vnic-conn-policy

• create egress-policy

• create epuser

• create eth-if

• create eth-policy

• create fcoe-if

• create fc-policy

• create folder

• create fw-host-pack

• create fw-mgmt-pack

• create hv-conn

• create import-config

• create initiator

• create interface

• create ipmi-access-profile

• create keyring

• create lan

• create local

• create local-disk-config

• create local-disk-config-policy

• create locale

• create local-user

• create mac-pool

• create mac-security

• create member-port

• create memory

• create ntp-server

• create nwctrl-policy

• create org

• create org-ref

• create pack-image

• create path

• create physical-qual

• create pin-group

• create policy

• create pooling-policy

• create port-channel

• create port-profile (eth-uplink)

• create port-profile (profile-set)

• create processor

• create profile

• create qos-policy

• create role

• create san-image

• create scrub-policy

• create server

• create server-autoconfig-policy

• create server-disc-policy

• create server-inherit-policy

• create server-pool

• create server-qual

• create service-profile

• create slot

• create snmp-trap

• create snmp-user

• create sol-config

• create sol-policy

• create stats-threshold-policy

• create storage

• create threshold-value

• create trustpoint

• create uuid-suffix-pool

• create vcenter

• create vcon

• create vcon-policy

• create vhba

• create vhba-templ

• create virtual-media

• create vlan

• create vlan (port-profile)

• create vnic

• create vnic-egress-policy

• create vnic-templ

• create vsan

• create wwn-pool

• cycle

• decommission chassis

• decommission server

• delete adapter

• delete backup

• delete block

• delete boot-definition

• delete boot-policy

• delete certreq

• delete chassis

• delete class chassis-stats

• delete class cpu-env-stats

• delete class dimm-stats

• delete class ether-error-stats

• delete class ether-if-stats

• delete class ether-loss-stats

• delete class ethernet-port-err-stats

• delete class ethernet-port-multicast-stats

• delete class ethernet-port-over-under-sized-stats

• delete class ethernet-port-stats

• delete class ethernet-port-stats-by-size-large-packets

• delete class ethernet-port-stats-by-size-small-packets

• delete class ether-rx-stats

• delete class ether-tx-stats

• delete client

• delete cpu

• delete data-center

• delete default-behavior

• delete destination

• delete distributed-virtual-switch

• delete dns

• delete dynamic-vnic-conn

• delete dynamic-vnic-conn-policy

• delete egress-policy

• delete epuser

• delete eth-if

• delete eth-policy

• delete fc-policy

• delete folder

• delete image

• delete import-config

• delete initiator

• delete interface

• delete ipmi-access-profile

• delete keyring

• delete lan

• delete local

• delete locale

• delete local-disk-config

• delete local-user

• delete mac-pool

• delete mac-security

• delete member-port

• delete memory

• delete nwctrl-policy

• delete org-ref

• delete path

• delete physical-qual

• delete pin-group

• delete policy

• delete pooling-policy

• delete port-channel

• delete port-profile (profile-set)

• delete processor

• delete qos-policy

• delete role

• delete scrub-policy

• delete server

• delete server-disc-policy

• delete server-pool

• delete server-qual

• delete storage

• delete target

• delete threshold-value

• delete trustpoint

• delete uuid-suffix-pool

• delete vcenter

• delete vcon

• delete vcon-policy

• delete vhba

• delete vlan

• delete vnic

• delete vnic-templ

• delete vsan

• delete wwn-pool

• dir

• disable (distributed-virtual-switch)

• disable cdp

• disable cimxml

• disable core-export-target

• disable http

• disable https

• disable locator-led

• disable snmp

• disable syslog

• disable telnet-server

• disassociate

• discard-buffer

• download image

• enable (distributed-virtual-switch)

• enable cdp

• enable cimxml

• enable cluster

• enable core-export-target

• enable http

• enable https

• enable locator-led

• enable snmp

• enable syslog

• enable telnet-server

• enter adapter

• enter chassis

• enter class cpu-env-stats

• enter class ethernet-port-err-stats

• enter class ethernet-port-multicast-stats

• enter class ethernet-port-over-under-sized-stats

• enter class ethernet-port-stats

• enter class ethernet-port-stats-by-size-large-packets

• enter class ethernet-port-stats-by-size-small-packets

• enter client

• enter data-center

• enter default-behavior

• enter distributed-virtual-switch

• enter dynamic-vnic-conn

• enter dynamic-vnic-conn-policy

• enter eth-policy

• enter fc-policy

• enter folder

• enter memory

• enter nwctrl-policy

• enter policy

• enter processor

• enter qos-policy

• enter storage

• enter threshold-value

• enter vcenter

• enter vcon

• enter vcon-policy

• enter vlan

• enter vlan (port-profile)

• erase configuration

• erase-log-config

• install-license

• ls

• mkdir

• move

• ping

• power

• pwd

• reboot

• recommission chassis

• recover-bios

• remove alertgroups

• remove backup action

• remove privilege

• remove server

• reset

• reset pers-bind

• reset-cmos

• rmdir

• run-script

• save

• scope adapter

• scope backup

• scope block

• scope bmc

• scope boardcontroller

• scope boot-definition

• scope boot-policy

• scope capability

• scope cap-qual

• scope cat-updater

• scope cert-store

• scope chassis

• scope chassis-disc-policy

• scope cimc

• scope class cpu-env-stats

• scope class ethernet-port-err-stats

• scope class ethernet-port-multicast-stats

• scope class ethernet-port-over-under-sized-stats

• scope class ethernet-port-stats

• scope class ethernet-port-stats-by-size-large-packets

• scope class ethernet-port-stats-by-size-small-packets

• scope client

• scope data-center

• scope default-behavior

• scope distributed-virtual-switch

• scope dynamic-vnic-conn

• scope egress-policy

• scope eth-best-effort

• scope eth-classified

• scope eth-policy

• scope eth-server

• scope eth-uplink

• scope extension-key

• scope fabric

• scope fabric-interconnect

• scope fc-policy

• scope fc-uplink

• scope firmware

• scope flow-control

• scope folder

• scope import-config

• scope iom

• scope ipmi-access-profile

• scope ldap

• scope locale

• scope monitoring

• scope nwctrl-policy

• scope org

• scope policy

• scope port-channel

• scope port-profile

• scope profile-set

• scope psu-policy

• scope qos

• scope qos-policy

• scope radius

• scope role

• scope security

• scope server

• scope server-qual

• scope services

• scope snmp-user

• scope system

• scope tacacs

• scope threshold-value

• scope vcenter

• scope vcon-policy

• scope vhba

• scope vhba-templ

• scope virtual-machine

• scope vlan

• scope vm-mgmt

• scope vmware

• scope vnic

• scope vnic-templ

• scope wwn-pool

• send

• send-syslog

• send-test-alert

• set action

• set adaptor-profile

• set adminstate

• set admin-state

• set admin-vcon

• set aes-128

• set agent-policy

• set alertgroups

• set all

• set arch

• set attribute

• set auth

• set authentication console

• set authentication default

• set authport

• set backup action

• set backup clear-on-backup

• set backup destination

• set backup format

• set backup hostname

• set backup interval

• set backup password

• set backup protocol

• set backup remote-path

• set backup user

• set basedn

• set binddn

• set bios-settings-scrub

• set blocksize

• set boot-policy

• set cert

• set certchain

• set certificate

• set cimxml port

• set clear-action

• set cli suppress-field-spillover

• set cli suppress-headers

• set cli table-field-delimiter

• set clock (memory)

• set clock (system)

• set collection-interval

• set community

• set comp-queue count

• set console-redir-config baud-rate

• set console-redir-config console-redir

• set contact

• set contract-id

• set core-export-target path

• set core-export-target port

• set core-export-target server-description

• set core-export-target server-name

• set cos

• set customer-id

• set data-center

• set data-center-folder

• set deescalating

• set default-net

• set descr

• set description

• set descr (vcon-policy)

• set destination org

• set disk-scrub

• set domain-name

• set drop

• set dvs

• set dynamic-eth

• set email

• set enforce-vnic-name

• set enhanced-intel-speedstep-config

• set error-recovery error-detect-timeout

• set error-recovery fcp-error-recovery

• set error-recovery link-down-timeout

• set error-recovery port-down-io-retry-count

• set error-recovery port-down-timeout

• set error-recovery resource-allocation-timeout

• set escalating

• set expiration

• set fabric

• set failover timeout

• set fc-if name

• set fcoe-vlan

• set file size

• set filter

• set firstname

• set flap-interval

• set flow-control-policy

• set folder

• set forged-transmit

• set format

• set from-email

• set host

• set host-fw-policy

• set hostname

• set hostname

• set http port

• set https keyring

• set https port

• set hyper-threading-config

• set identity dynamic-mac

• set identity dynamic-uuid

• set identity dynamic-wwnn

• set identity dynamic-wwpn

• set identity mac-pool

• set identity uuid-suffix-pool

• set identity wwnn-pool

• set identity wwpn-pool

• set intel-turbo-boost-config

• set intel-vt-config

• set intel-vt-directed-io-config

• set interrupt coalescing-time

• set interrupt coalescing-type

• set interrupt count

• set interrupt mode

• set interval-days

• set ipmi-access-profile

• set key (server)

• set key (extension-key)

• set lastname

• set level

• set local-disk-policy

• set lun

• set lv-dimm-support-config

• set mac aging

• set mac-pool

• set maxcap

• set maxcores

• set max-field-size

• set maximum

• set max-ports

• set maxprocs

• set maxsize

• set maxthreads

• set memory-mirroring-mode

• set memory-ras-config

• set mgmt-fw-policy

• set mincap

• set mincores

• set minprocs

• set minthreads

• set mode (eth-uplink)

• set mode (fw-pack)

• set mode (local-disk)

• set model-regex

• set module

• set modulus

• set mtu

• set mtu (eth-best-effort)

• set mtu (vnic)

• set multicast-optimize

• set multicastoptimize (eth-best-effort)

• set name

• set native

• set normal-value

• set numa-config

• set numberofblocks

• set nw-control-policy

• set offload large-receive

• set offload tcp-rx-checksum

• set offload tcp-segment

• set offload tcp-tx-checksum

• set order (device boot order)

• set order (vhba pci scan order)

• set order (vnic relative order)

• set out-of-band

• set password

• set password (snmp-user)

• set path

• set perdiskcap

• set pers-bind

• set phone

• set phone-contact

• set pin-group

• set pool

• set port

• set port io-throttle-count

• set port max-field-size

• set port max-luns

• set port-f-logi retries

• set port-f-logi timeout

• set port-p-logi retries

• set port-p-logi timeout

• set power-budget committed

• set preserve-pooled-values

• set prio

• set privilege

• set priv-password

• set processor-c3-report-config

• set processor-c6-report-config

• set protocol

• set qos-policy

• set qualifier

• set quiet-boot-config

• set rate

• set reboot-on-update

• set receive

• set recv-queue count

• set recv-queue ring-size

• set redundancy

• set regenerate

• set remote-file

• set reply-to-email

• set reporting-interval

• set resume-ac-on-power-loss-config

• set retention-interval

• set retries

• set rootdn

• set rss receivesidescaling

• set scrub-policy

• set scsi-io count

• set scsi-io ring-size

• set send

• set send-periodically

• set server

• set site-id

• set size

• set snmp community

• set sol-policy

• set speed

• set src-templ-name

• set sshkey

• set ssl

• set stats-policy

• set stepping

• set street-address

• set switch-priority

• set syslog console

• set syslog file

• set syslog min-level

• set syslog monitor

• set syslog remote-destination

• set target

• set template

• set template-name

• set throttling

• set timeofday-hour

• set timeofday-minute

• set timeout

• set timezone

• set trans-queue count

• set trans-queue ring-size

• set trustpoint

• set type (backup)

• set type (partition)

• set type (template)

• set units

• set uplink-fail-action

• set user

• set userid

• set user-label

• set uuid-prefix

• set v3privilege

• set vcon

• set vcon-profile

• set version

• set version (snmp-trap)

• set vhba

• set virtual-ip

• set vnic

• set weight

• set width

• set work-queue count

• set work-queue ring-size

• set wwn

• set wwpn-pool

• show activate status

• show adapter

• show assoc

• show audit-logs

• show authentication

• show backup

• show backup (ep-log-policy)

• show bios

• show bmc

• show boot-definition

• show boot-order

• show boot-policy

• show callhome

• show cap-qual

• show cat-updater

• show certreq

• show chassis

• show cimc

• show cimxml

• show class cpu-stats

• show class ethernet-port-err-stats

• show class ethernet-port-multicast-stats

• show class ethernet-port-over-under-sized-stats

• show class ethernet-port-stats

• show class ethernet-port-stats-by-size-large-packets

• show class ethernet-port-stats-by-size-small-packets

• show cli

• show clock (system)

• show cluster

• show connectivity

• show core-export-target

• show cores

• show cpu

• show destination

• show disk

• show distributed-virtual-switch

• show dns

• show download-task

• show dynamic-conn-policy

• show egress-policy

• show environment

• show epuser

• show error-recovery

• show eth-classified

• show eth-if

• show eth-profile

• show eth-uplink

• show event

• show extension-key

• show ext-eth-if

• show ext-ipv6-rss-hash

• show fabric

• show fabric-interconnect

• show fabric-interconnect inventory

• show fabric-interconnect mode

• show failover

• show fan

• show fan-module

• show fault policy

• show fc

• show fc-if

• show fc-profile

• show identity (server)

• show identity (service-profile)

• show identity mac-addr

• show identity uuid

• show identity wwn

• show license brief

• show license default

• show license file

• show license host-id

• show license usage

• show nwctrl-policy

• show power-budget

• show psu-policy

• show security fsm status

• show sel

• show server actual-boot-order

• show server adapter

• show server adapter identity

• show server adapter inventory

• show server adapter layer2

• show server adapter status

• show server boot-order

• show server cpu

• show server identity

• show snmp-user

• show sshkey

• show stats mb-power-stats

• show vcenter

• show vcon

• show vcon-policy

• show virtual-machine

• ssh

• tail-mgmt-log

• telnet

• terminal length

• terminal monitor

• terminal session-timeout

• terminal width

• top

• traceroute

• up

• update catalog

• update firmware

• where

Commands

---

• acknowledge chassis
• acknowledge fault
• acknowledge server
• acknowledge slot
• activate firmware
• activate firmware (fabric)
• add alertgroups
• add backup action
• add privilege
• associate server
• associate server-pool
• backup sel
• cd
• clear alertgroups
• clear backup action
• clear cores
• clear license
• clear sel
• clear sshkey
• cluster force primary
• cluster lead
• commit-buffer
• connect adapter
• connect bmc
• connect clp
• connect iom
• connect local-mgmt
• connect nxos
• copy
• create adapter
• create backup
• create bios-policy
• create block
• create boot-definition
• create boot-policy
• create cap-qual
• create certreq
• create chassis
• create class chassis-stats
• create class cmc-stats
• create class cpu-env-stats
• create class dimm-stats
• create class ether-error-stats
• create class ether-if-stats
• create class ether-loss-stats
• create class ethernet-port-err-stats
• create class ethernet-port-multicast-stats
• create class ethernet-port-over-under-sized-stats
• create class ethernet-port-stats
• create class ethernet-port-stats-by-size-large-packets
• create class ethernet-port-stats-by-size-small-packets
• create class ether-rx-stats
• create class ether-tx-stats
• create class fan-module-stats
• create class fan-stats
• create class fc-error-stats
• create class fc-if-event-stats
• create class fc-if-fc4-counters
• create class fc-if-frame-stats
• create class fc-port-stats
• create class fc-stats
• create class mb-power-stats
• create class mb-temp-stats
• create class memory-runtime
• create class menlo-dce-port-stats
• create class menlo-eth-error-stats
• create class menlo-eth-stats
• create class menlo-fc-error-stats
• create class menlo-fc-stats
• create class menlo-host-port-stats
• create class menlo-mcpu-error-stats
• create class menlo-mcpu-stats
• create class menlo-net-eg-stats
• create class menlo-net-in-stats
• create class menlo-q-error-stats
• create class menlo-q-stats
• create class processor-runtime
• create class psu-input-stats
• create class psu-stats
• create class system-stats
• create client
• create class vnic-stats
• create cpu
• create data-center
• create default-behavior
• create destination
• create distributed-virtual-switch
• create dns
• create dynamic-vnic-conn
• create dynamic-vnic-conn-policy
• create egress-policy
• create epuser
• create eth-if
• create eth-policy
• create fcoe-if
• create fc-policy
• create folder
• create fw-host-pack
• create fw-mgmt-pack
• create hv-conn
• create import-config
• create initiator
• create interface
• create ipmi-access-profile
• create keyring
• create lan
• create local
• create local-disk-config
• create local-disk-config-policy
• create locale
• create local-user
• create mac-pool
• create mac-security
• create member-port
• create memory
• create ntp-server
• create nwctrl-policy
• create org
• create org-ref
• create pack-image
• create path
• create physical-qual
• create pin-group
• create policy
• create pooling-policy
• create port-channel
• create port-profile (eth-uplink)
• create port-profile (profile-set)
• create processor
• create profile
• create qos-policy
• create role
• create san-image
• create scrub-policy
• create server
• create server-autoconfig-policy
• create server-disc-policy
• create server-inherit-policy
• create server-pool
• create server-qual
• create service-profile
• create slot
• create snmp-trap
• create snmp-user
• create sol-config
• create sol-policy
• create stats-threshold-policy
• create storage
• create threshold-value
• create trustpoint
• create uuid-suffix-pool
• create vcenter
• create vcon
• create vcon-policy
• create vhba
• create vhba-templ
• create virtual-media
• create vlan
• create vlan (port-profile)
• create vnic
• create vnic-egress-policy
• create vnic-templ
• create vsan
• create wwn-pool
• cycle
• decommission chassis
• decommission server
• delete adapter
• delete backup
• delete block
• delete boot-definition
• delete boot-policy
• delete certreq
• delete chassis
• delete class chassis-stats
• delete class cpu-env-stats
• delete class dimm-stats
• delete class ether-error-stats
• delete class ether-if-stats
• delete class ether-loss-stats
• delete class ethernet-port-err-stats
• delete class ethernet-port-multicast-stats
• delete class ethernet-port-over-under-sized-stats
• delete class ethernet-port-stats
• delete class ethernet-port-stats-by-size-large-packets
• delete class ethernet-port-stats-by-size-small-packets
• delete class ether-rx-stats
• delete class ether-tx-stats
• delete client
• delete cpu
• delete data-center
• delete default-behavior
• delete destination
• delete distributed-virtual-switch
• delete dns
• delete dynamic-vnic-conn
• delete dynamic-vnic-conn-policy
• delete egress-policy
• delete epuser
• delete eth-if
• delete eth-policy
• delete fc-policy
• delete folder
• delete image
• delete import-config
• delete initiator
• delete interface
• delete ipmi-access-profile
• delete keyring
• delete lan
• delete local
• delete locale
• delete local-disk-config
• delete local-user
• delete mac-pool
• delete mac-security
• delete member-port
• delete memory
• delete nwctrl-policy
• delete org-ref
• delete path
• delete physical-qual
• delete pin-group
• delete policy
• delete pooling-policy
• delete port-channel
• delete port-profile (profile-set)
• delete processor
• delete qos-policy
• delete role
• delete scrub-policy
• delete server
• delete server-disc-policy
• delete server-pool
• delete server-qual
• delete storage
• delete target
• delete threshold-value
• delete trustpoint
• delete uuid-suffix-pool
• delete vcenter
• delete vcon
• delete vcon-policy
• delete vhba
• delete vlan
• delete vnic
• delete vnic-templ
• delete vsan
• delete wwn-pool
• dir
• disable (distributed-virtual-switch)
• disable cdp
• disable cimxml
• disable core-export-target
• disable http
• disable https
• disable locator-led
• disable snmp
• disable syslog
• disable telnet-server
• disassociate
• discard-buffer
• download image
• enable (distributed-virtual-switch)
• enable cdp
• enable cimxml
• enable cluster
• enable core-export-target
• enable http
• enable https
• enable locator-led
• enable snmp
• enable syslog
• enable telnet-server
• enter adapter
• enter chassis
• enter class cpu-env-stats
• enter class ethernet-port-err-stats
• enter class ethernet-port-multicast-stats
• enter class ethernet-port-over-under-sized-stats
• enter class ethernet-port-stats
• enter class ethernet-port-stats-by-size-large-packets
• enter class ethernet-port-stats-by-size-small-packets
• enter client
• enter data-center
• enter default-behavior
• enter distributed-virtual-switch
• enter dynamic-vnic-conn
• enter dynamic-vnic-conn-policy
• enter eth-policy
• enter fc-policy
• enter folder
• enter memory
• enter nwctrl-policy
• enter policy
• enter processor
• enter qos-policy
• enter storage
• enter threshold-value
• enter vcenter
• enter vcon
• enter vcon-policy
• enter vlan
• enter vlan (port-profile)
• erase configuration
• erase-log-config
• install-license
• ls
• mkdir
• move
• ping
• power
• pwd
• reboot
• recommission chassis
• recover-bios
• remove alertgroups
• remove backup action
• remove privilege
• remove server
• reset
• reset pers-bind
• reset-cmos
• rmdir
• run-script
• save
• scope adapter
• scope backup
• scope block
• scope bmc
• scope boardcontroller
• scope boot-definition
• scope boot-policy
• scope capability
• scope cap-qual
• scope cat-updater
• scope cert-store
• scope chassis
• scope chassis-disc-policy
• scope cimc
• scope class cpu-env-stats
• scope class ethernet-port-err-stats
• scope class ethernet-port-multicast-stats
• scope class ethernet-port-over-under-sized-stats
• scope class ethernet-port-stats
• scope class ethernet-port-stats-by-size-large-packets
• scope class ethernet-port-stats-by-size-small-packets
• scope client
• scope data-center
• scope default-behavior
• scope distributed-virtual-switch
• scope dynamic-vnic-conn
• scope egress-policy
• scope eth-best-effort
• scope eth-classified
• scope eth-policy
• scope eth-server
• scope eth-uplink
• scope extension-key
• scope fabric
• scope fabric-interconnect
• scope fc-policy
• scope fc-uplink
• scope firmware
• scope flow-control
• scope folder
• scope import-config
• scope iom
• scope ipmi-access-profile
• scope ldap
• scope locale
• scope monitoring
• scope nwctrl-policy
• scope org
• scope policy
• scope port-channel
• scope port-profile
• scope profile-set
• scope psu-policy
• scope qos
• scope qos-policy
• scope radius
• scope role
• scope security
• scope server
• scope server-qual
• scope services
• scope snmp-user
• scope system
• scope tacacs
• scope threshold-value
• scope vcenter
• scope vcon-policy
• scope vhba
• scope vhba-templ
• scope virtual-machine
• scope vlan
• scope vm-mgmt
• scope vmware
• scope vnic
• scope vnic-templ
• scope wwn-pool
• send
• send-syslog
• send-test-alert
• set action
• set adaptor-profile
• set adminstate
• set admin-state
• set admin-vcon
• set aes-128
• set agent-policy
• set alertgroups
• set all
• set arch
• set attribute
• set auth
• set authentication console
• set authentication default
• set authport
• set backup action
• set backup clear-on-backup
• set backup destination
• set backup format
• set backup hostname
• set backup interval
• set backup password
• set backup protocol
• set backup remote-path
• set backup user
• set basedn
• set binddn
• set bios-settings-scrub
• set blocksize
• set boot-policy
• set cert
• set certchain
• set certificate
• set cimxml port
• set clear-action
• set cli suppress-field-spillover
• set cli suppress-headers
• set cli table-field-delimiter
• set clock (memory)
• set clock (system)
• set collection-interval
• set community
• set comp-queue count
• set console-redir-config baud-rate
• set console-redir-config console-redir
• set contact
• set contract-id
• set core-export-target path
• set core-export-target port
• set core-export-target server-description
• set core-export-target server-name
• set cos
• set customer-id
• set data-center
• set data-center-folder
• set deescalating
• set default-net
• set descr
• set description
• set descr (vcon-policy)
• set destination org
• set disk-scrub
• set domain-name
• set drop
• set dvs
• set dynamic-eth
• set email
• set enforce-vnic-name
• set enhanced-intel-speedstep-config
• set error-recovery error-detect-timeout
• set error-recovery fcp-error-recovery
• set error-recovery link-down-timeout
• set error-recovery port-down-io-retry-count
• set error-recovery port-down-timeout
• set error-recovery resource-allocation-timeout
• set escalating
• set expiration
• set fabric
• set failover timeout
• set fc-if name
• set fcoe-vlan
• set file size
• set filter
• set firstname
• set flap-interval
• set flow-control-policy
• set folder
• set forged-transmit
• set format
• set from-email
• set host
• set host-fw-policy
• set hostname
• set hostname
• set http port
• set https keyring
• set https port
• set hyper-threading-config
• set identity dynamic-mac
• set identity dynamic-uuid
• set identity dynamic-wwnn
• set identity dynamic-wwpn
• set identity mac-pool
• set identity uuid-suffix-pool
• set identity wwnn-pool
• set identity wwpn-pool
• set intel-turbo-boost-config
• set intel-vt-config
• set intel-vt-directed-io-config
• set interrupt coalescing-time
• set interrupt coalescing-type
• set interrupt count
• set interrupt mode
• set interval-days
• set ipmi-access-profile
• set key (server)
• set key (extension-key)
• set lastname
• set level
• set local-disk-policy
• set lun
• set lv-dimm-support-config
• set mac aging
• set mac-pool
• set maxcap
• set maxcores
• set max-field-size
• set maximum
• set max-ports
• set maxprocs
• set maxsize
• set maxthreads
• set memory-mirroring-mode
• set memory-ras-config
• set mgmt-fw-policy
• set mincap
• set mincores
• set minprocs
• set minthreads
• set mode (eth-uplink)
• set mode (fw-pack)
• set mode (local-disk)
• set model-regex
• set module
• set modulus
• set mtu
• set mtu (eth-best-effort)
• set mtu (vnic)
• set multicast-optimize
• set multicastoptimize (eth-best-effort)
• set name
• set native
• set normal-value
• set numa-config
• set numberofblocks
• set nw-control-policy
• set offload large-receive
• set offload tcp-rx-checksum
• set offload tcp-segment
• set offload tcp-tx-checksum
• set order (device boot order)
• set order (vhba pci scan order)
• set order (vnic relative order)
• set out-of-band
• set password
• set password (snmp-user)
• set path
• set perdiskcap
• set pers-bind
• set phone
• set phone-contact
• set pin-group
• set pool
• set port
• set port io-throttle-count
• set port max-field-size
• set port max-luns
• set port-f-logi retries
• set port-f-logi timeout
• set port-p-logi retries
• set port-p-logi timeout
• set power-budget committed
• set preserve-pooled-values
• set prio
• set privilege
• set priv-password
• set processor-c3-report-config
• set processor-c6-report-config
• set protocol
• set qos-policy
• set qualifier
• set quiet-boot-config
• set rate
• set reboot-on-update
• set receive
• set recv-queue count
• set recv-queue ring-size
• set redundancy
• set regenerate
• set remote-file
• set reply-to-email
• set reporting-interval
• set resume-ac-on-power-loss-config
• set retention-interval
• set retries
• set rootdn
• set rss receivesidescaling
• set scrub-policy
• set scsi-io count
• set scsi-io ring-size
• set send
• set send-periodically
• set server
• set site-id
• set size
• set snmp community
• set sol-policy
• set speed
• set src-templ-name
• set sshkey
• set ssl
• set stats-policy
• set stepping
• set street-address
• set switch-priority
• set syslog console
• set syslog file
• set syslog min-level
• set syslog monitor
• set syslog remote-destination
• set target
• set template
• set template-name
• set throttling
• set timeofday-hour
• set timeofday-minute
• set timeout
• set timezone
• set trans-queue count
• set trans-queue ring-size
• set trustpoint
• set type (backup)
• set type (partition)
• set type (template)
• set units
• set uplink-fail-action
• set user
• set userid
• set user-label
• set uuid-prefix
• set v3privilege
• set vcon
• set vcon-profile
• set version
• set version (snmp-trap)
• set vhba
• set virtual-ip
• set vnic
• set weight
• set width
• set work-queue count
• set work-queue ring-size
• set wwn
• set wwpn-pool
• show activate status
• show adapter
• show assoc
• show audit-logs
• show authentication
• show backup
• show backup (ep-log-policy)
• show bios
• show bmc
• show boot-definition
• show boot-order
• show boot-policy
• show callhome
• show cap-qual
• show cat-updater
• show certreq
• show chassis
• show cimc
• show cimxml
• show class cpu-stats
• show class ethernet-port-err-stats
• show class ethernet-port-multicast-stats
• show class ethernet-port-over-under-sized-stats
• show class ethernet-port-stats
• show class ethernet-port-stats-by-size-large-packets
• show class ethernet-port-stats-by-size-small-packets
• show cli
• show clock (system)
• show cluster
• show connectivity
• show core-export-target
• show cores
• show cpu
• show destination
• show disk
• show distributed-virtual-switch
• show dns
• show download-task
• show dynamic-conn-policy
• show egress-policy
• show environment
• show epuser
• show error-recovery
• show eth-classified
• show eth-if
• show eth-profile
• show eth-uplink
• show event
• show extension-key
• show ext-eth-if
• show ext-ipv6-rss-hash
• show fabric
• show fabric-interconnect
• show fabric-interconnect inventory
• show fabric-interconnect mode
• show failover
• show fan
• show fan-module
• show fault policy
• show fc
• show fc-if
• show fc-profile
• show identity (server)
• show identity (service-profile)
• show identity mac-addr
• show identity uuid
• show identity wwn
• show license brief
• show license default
• show license file
• show license host-id
• show license usage
• show nwctrl-policy
• show power-budget
• show psu-policy
• show security fsm status
• show sel
• show server actual-boot-order
• show server adapter
• show server adapter identity
• show server adapter inventory
• show server adapter layer2
• show server adapter status
• show server boot-order
• show server cpu
• show server identity
• show snmp-user
• show sshkey
• show stats mb-power-stats
• show vcenter
• show vcon
• show vcon-policy
• show virtual-machine
• ssh
• tail-mgmt-log
• telnet
• terminal length
• terminal monitor
• terminal session-timeout
• terminal width
• top
• traceroute
• up
• update catalog
• update firmware
• where

acknowledge chassis

To acknowledge a chassis, use the acknowledge chassis command.

acknowledge chassis id

Syntax Description

id	Chassis identification number. The range of valid values is 1 to 255.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to verify the existence of devices in your network. For example, you can acknowledge a chassis that was recently commissioned, to ensure that it exists.

Examples

This example shows how to acknowledge a chassis:

switch-A# acknowledge chassis 10
switch-A* # commit-buffer
switch-A #                                           

Related Commands

Command	Description
show chassis
show server

acknowledge fault

To acknowledge a fault, use the acknowledge fault command.

acknowledge fault id

Syntax Description

id	Fault identification number. The range of valid values is 0 to 9223372036854775807.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

The following example shows how to acknowledge a fault:

switch-A# acknowledge fault 1
switch-A* # commit-buffer
switch-A #                                           
                                          

Related Commands

Command	Description
show cli
show fault

acknowledge server

To acknowledge a server, use the acknowledge server command.

acknowledge server { chassis-id / blade-id | slot-id }

Syntax Description

chassis-id / blade-id	Chassis and blade identification numbers.
slot-id	Slot identification number. The range of valid values is 1 to 8.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to verify the existence of devices in your network. For example, you can acknowledge a server that was recently commissioned, to ensure that it exists. slot -id is used only in /chassis mode.

Examples

The following example shows how to acknowledge a server in /chassis mode:

switch-A# scope chassis 1
switch-A /chassis # acknowledge server 2
switch-A /chassis* # commit-buffer                                          
switch-A /chassis #                                          

Related Commands

Command	Description
show chassis
show server

acknowledge slot

To acknowledge a slot, use the acknowledge slot command.

acknowledge slot { chassis-id / blade-id | slot-id }

Syntax Description

chassis-id / blade-id	Sever identification number.
slot-id	Slot identification number. The range of valid values is 1 to 8.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to verify the existence of devices in your network. For example, you can acknowledge a chassis that was recently commissioned using slot -id , to ensure that it exists. slot -id is used only in /chassis mode.

Examples

The following example shows how to acknowledge a slot in /chassis mode:

switch-A# scope chassis 1
switch-A /chassis # acknowledge slot 1 
switch-A /chassis* # commit-buffer                                         
switch-A /chassis #                                           

Related Commands

Command	Description
show server
show slot

activate firmware

To activate firmware for a device, use the activate firmware command.

activate firmware version [ignorecompcheck] [set-startup-only] +

Syntax Description

version	Firmware version.
ignorecompcheck	(Optional) Ignores the results of the compatability check.
set-startup-only	(Optional) Activates the firmware only on next startup.

Command Default

None

Command Modes

Board controller (/chassis/system/boardcontroller)

Input output module (/chassis/iom)

System (/system)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use the ignorecompcheck keyword to ignore the results of the automatic compatability check when you activate the firmware.

Use the set-startup-only keyword to activate the specified Input output module (IOM) firmware version only on the next startup of the IOM. The system will not restart at this time. This keyword is available only in the IOM command mode.

Examples

The following example shows how to activate a specific version of system software, ignoring the compatibility check:

switch-A# scope system
switch-A /system # activate firmware 3.0 ignorecompcheck
switch-A /system* # commit-buffer
switch-A /system # 

Related Commands

Command	Description
show firmware
show version

activate firmware (fabric)

To activate kernal or system firmware on a fabric interconnect, use the activate firmware command.

activate firmware { kernel-version kernel-version | system-version system-version } [ignorecompcheck] [force] +

Syntax Description

kernel-version	Specifies switch kernel firmware.
kernel-version	Kernel firmware version.
system-version	Specifies switch system firmware.
system-version	System firmware version.
ignorecompcheck	(Optional) Ignores the results of the compatability check.
force	(Optional) Forces the upgrade.

Command Default

None

Command Modes

Fabric interconnect (/fabric)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use the ignorecompcheck keyword to ignore the results of the automatic compatability check when you activate the firmware.

Examples

The following example shows how to activate a specific version of kernal software on fabric interconnect A, ignoring the compatibility check:

switch-A# scope fabric a
switch-A /fabric # activate firmware kernel-version 3.0 ignorecompcheck
switch-A /fabric* # commit-buffer
switch-A /fabric # 

Related Commands

Command	Description
show firmware
show version

add alertgroups

To add more alert groups to a Call Home profile, use the add alertgroups command.

add alertgroups [ ciscotac ] [ diagnostic ] [ environmental ] [ inventory ] [ license ] [ lifecycle ] [ linecard ] [ supervisor ] [ syslogport ] [ system ] [ test ] +

Syntax Description

ciscotac	Specifies the Cisco Technical Assistance Center (TAC) alert group.
diagnostic	Specifies the diagnostic alert group.
environmental	Specifies the environmental alert group.
inventory	Specifies the inventory alert group.
license	Specifies the license alert group.
lifecycle	Specifies the lifecycle alert group.
linecard	Specifies the line card alert group.
supervisor	Specifies the supervisor alert group.
syslogport	Specifies the syslog port alert group.
system	Specifies the system alert group.
test	Specifies the test alert group.

Command Default

None

Command Modes

Profile (/monitoring/callhome/profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to add more predefined Call Home alert groups to an existing alert group list within a Call Home profile.

Examples

This example shows how to add diagnostic and license alert groups to an existing Call Home profile:

switch-A# scope monitoring
switch-A /monitoring # scope callhome                                                                        
switch-A /monitoring/callhome # scope profile profileOne 
switch-A /monitoring/callhome/profile # add alertgroups diagnostic license 
switch-A /monitoring/callhome/profile* # commit-buffer
switch-A /monitoring/callhome/profile #                                                                       

Related Commands

Command	Description
remove alertgroups
set alertgroups

add backup action

To add an additional action or actions that will trigger a backup of the system event log, use the add backup actioncommand.

add backup action [log-full] [none] [on-change-of-association] [on-clear] [timer]

Syntax Description

log-full	Specifies that the log is backed up when it is full.
none	Specifies no action.
on-change-of-association	Specifies that the log is backed up when the server changes associations.
on-clear	Specifies that the log is backed up when it is cleared.
timer	Specifies that the log is backed up at an interval.

Command Default

None

Command Modes

Endpoint log policy (/org/ep-log-policy)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Use this command to add an additional action or actions that will trigger a backup of the system event log. Previously configured actions are retained.

Examples

This example shows how to add an action to trigger a backup of the system event log when the log is full:

switch-A# scope org
switch-A /org # scope ep-log-policy sel
switch-A /org/ep-log-policy # add backup action log-full
switch-A /org/ep-log-policy* # commit-buffer
switch-A /org/ep-log-policy # 

Related Commands

Command	Description
remove backup action
set backup action
show backup

add privilege

To add privileges, use the add privilege command.

add privilege { aaa | admin | ext-lan-config | ext-lan-policy | ext-lan-qos | ext-lan-security | ext-san-config | ext-san-policy | ext-san-qos | ext-san-security | fault | service-profile-config | service-profile-config-policy | service-profile-network | service-profile-network-policy | service-profile-qos | service-profile-qos-policy | service-profile-security | service-profile-security-policy | service-profile-server | service-profile-server-policy | service-profile-storage | service-profile-storage-policy | operations | server-equipment | server-maintenance | server-policy | server-security | pod-config | pod-policy | pod-qos | pod-security | read-only } +

Syntax Description

aaa	Specifies AAA privileges.
admin	Specifies admin privileges.
ext-lan-config	Specifies external LAN configuration priveleges.
ext-lan-policy	Specifies external LAN policy privileges.
ext-lan-qos	Specifies external LAN QoS privileges.
ext-lan-security	Specifies external LAN security privileges.
ext-san-config	Specifies external SAN configuration privileges.
ext-san-policy	Specifies external SAN policy privileges.
ext-san-qos	Specifies external SAN QoS privileges.
ext-san-security	Specifies external SAN security privileges.
fault	Specifies fault privileges.
service-profile-config	Specifies service profile configuration privileges.
service-profile-config-policy	Specifies service profile configuration policy privileges.
service-profile-network	Specifies service profile network privileges.
service-profile-network-policy	Specifies service profile network policy privileges.
service-profile-qos	Specifies service profile QoS privileges.
service-profile-qos-policy	Specifies service profile QoS policy privileges.
service-profile-security	Specifies service profile security privileges.
service-profile-security-policy	Specifies service profile security policy privileges.
service-profile-server	Specifies service profile server privileges.
service-profile-server-policy	Specifies service profile server policy privileges.
service-profile-storage	Specifies service profile storage privileges.
service-profile-storage-policy	Specifies service profile storage policy privileges.
operations	Specifies operations privileges.
server-equipment	Specifies server equipment privileges.
server-maintenance	Specifies server maintenance privileges.
server-policy	Specifies server policy privileges.
server-security	Specifies server security privileges.
pod-config	Specifies pod configuration privileges.
pod-policy	Specifies pod policy privileges.
pod-qos	Specifies pod QoS privileges.
pod-security	Specifies pod security privileges.
read-only	Specifies read-only privileges.

Command Default

None

Command Modes

Role (/security/role)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to add privileges:

switch-A # scope security
switch-A /security # scope role role1
switch-A /security/role # add privilege ext-san-config ext-san-policy ext-san-qos ext-san-security 
switch-A /security/role* # commit-buffer
switch-A /security/role # 

associate server

To associate a server, use the associate server command.

associate server chassis-id/blade-id

Syntax Description

chassis-id/blade-id

Chassis and blade identification numbers. The range of valid values is 1 to 4294967295.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to associate a server:

switch-A# scope org 1
switch-A /org # scope service-profile 1                                          
switch-A /org/service-profile # associate server 1 
switch-A /org/service-profile* # commit-buffer
switch-A /org/service-profile #                                          

Related Commands

Command	Description
show assoc
show server

associate server-pool

To associate a server pool with a service profile, use the associate server-pool command.

associate server-pool server-pool [name]

Syntax Description

server-pool	Server pool name. The range of valid values is 1 to 16.
name	(Optional) Qualifier. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to associate a server pool:

switch-A# scope org 1
switch-A /org # scope service-profile 1                                             
switch-A /org/service-profile # associate server-pool 1 
switch-A /org/service-profile* # commit-buffer
switch-A /org/service-profile #                                             

Related Commands

Command	Description
show assoc
show server

backup sel

To back up the system event log (SEL), use the backup sel command.

backup sel server-id

Syntax Description

server-id

Specifies the chassis number and server number in the format A/B.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to back up the system event log (SEL) for a server. When entering this command in the command mode of the specific server (/chassis/server), do not enter the server-id .

Examples

This example shows how to back up the SEL for server 4 in chassis 2:

switch-A# backup sel 2/4
switch-A* # commit-buffer
switch-A# 

Related Commands

Command	Description

cd

To change directories, use the cd command in local management command mode.

cd { workspace: | [path] | volatile: | [path] | | [path] }

Syntax Description

workspace:	Specifies the workspace (flash) directory.
volatile:	Specifies the volatile directory.
path	Absolute or relative path.

Command Default

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.1(1)	This command was modified. The bootflash: keyword is replaced by the workspace: keyword.

Usage Guidelines

This command is available on the local management port command line. Use the connect local-mgmt command to connect to that command line.

This command operates on either the workspace (FLASH) or volatile (RAM) file system. To specify the file system, include the workspace: or volatile: keyword in the path. If the file system is not specified, the current working file system is assumed.

Examples

This example shows how to change directories:

switch-A# connect local-mgmt a
Cisco UCS 6100 Series Fabric Interconnect

TAC support: http://www.cisco.com/tac

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of 
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html

switch-A(local-mgmt)# cd volatile:/temp
Pubs-A(local-mgmt)# pwd
volatile:temp
switch-A(local-mgmt)# 

clear alertgroups

To clear all selected alert groups in a Call Home profile, use the clear alertgroups command.

clear alertgroups

This command has no arguments or keywords.

Command Default

None

Command Modes

Profile (/monitoring/callhome/profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to clear any previously configured alert group list within the Call Home profile.

Examples

This example shows how to clear alert groups in a Call Home profile:

switch-A# scope monitoring
switch-A /monitoring # scope callhome
switch-A /monitoring/callhome # scope profile profileOne 
switch-A /monitoring/callhome/profile # clear alertgroups
switch-A /monitoring/callhome/profile* # commit-buffer  
switch-A /monitoring/callhome/profile #

Related Commands

Command	Description
set alertgroups
show policy
show profile

clear backup action

To clear all selected actions that will trigger a backup of the system event log, use the clear backup actioncommand.

clear backup action

This command has no arguments or keywords.

Command Default

None

Command Modes

Endpoint log policy (/org/ep-log-policy)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Use this command to delete any previously configured list of actions that will trigger a backup of the system event log.

Examples

This example shows how to clear all selected actions that will trigger a backup of the system event log:

switch-A# scope org
switch-A /org # scope ep-log-policy sel
switch-A /org/ep-log-policy # clear backup action
switch-A /org/ep-log-policy* # commit-buffer
switch-A /org/ep-log-policy # 

Related Commands

Command	Description
set backup action
show backup

clear cores

To clear core files, use the clear cores command.

clear cores

This command has no arguments or keywords.

Command Default

None

Command Modes

Sysdebug (/monitoring/sysdebug)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Core files are records of core dumps. Use the clear cores command to clear information out of core dump records.

Examples

This example shows how to clear core files:

switch-A# scope monitoring
switch-A /monitoring # scope sysdebug                                       
switch-A /monitoring/sysdebug # clear cores
switch-A /monitoring/sysdebug # commit-buffer
switch-A /monitoring/sysdebug #                                        

Related Commands

Command	Description
show alert-groups
show cores

clear license

To remove a license, use the clear license command in local management command mode.

clear license license-file-name [force]

Syntax Description

license-file-name	The name of a license file.
force	(Optional)

Command Default

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to remove a license in local management command mode.

This command can be executed only on local fabric interconnect and only by the user admin.

This command is available on the local management port command line. Use the connect local-mgmt command to connect to that command line.

Examples

This example shows how to remove a license:

switch-A# connect local-mgmt a
Cisco UCS 6100 Series Fabric Interconnect

TAC support: http://www.cisco.com/tac

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of 
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html

switch-A(local-mgmt)#  clear license FibreChannel.lic
Clearing license FibreChannel.lic:
SERVER this_host ANY
VENDOR cisco
Enter yes (yes is the default) to continue with the license update.
Do you want to continue? (y/n) y
Clearing license ..done

switch-A(local-mgmt)# 

Related Commands

Command	Description
connect local-mgmt
show license brief

clear sel

To clear the contents of the system event log (SEL), use the clear sel command.

clear sel

This command has no arguments or keywords.

Command Default

None

Command Modes

Server (/chassis/server)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to clear the contents of the system event log (SEL).

Examples

This example shows how to clear the contents of the SEL:

switch-A# scope server 2/4
switch-A /chassis/server # clear sel
switch-A /chassis/server* # commit-buffer
switch-A /chassis/server #

Related Commands

Command	Description
show sel

clear sshkey

To clear from cache the SSH public key of a remote host, use the clear sshkey command in local management mode.

clear sshkey host-name

Syntax Description

host-name

Host name or IP address. Specify the IP address in the format A.B.C.D.

Command Default

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to clear from cache the SSH public key of a remote host that supports SSH.

This command is available on the local management port command line. Use the connect local-mgmt command to connect to that command line.

Examples

This example shows how to clear the SSH public key of a remote host:

switch-A # connect local-mgmt a
Cisco UCS 6100 Series Fabric Interconnect

TAC support: http://www.cisco.com/tac

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of 
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html

switch-A(local-mgmt)# clear sshkey 192.0.2.111
switch-A(local-mgmt)# 

Related Commands

Command	Description
connect local-mgmt

cluster force primary

To force a cluster to be the primary cluster, use the cluster force primary command.

cluster force primary

Command Default

This command has no arguments or keywords.

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The cluster commands are switch-specific local management commands. You have to execute a connect local-mgmt command to connect to the management port.

Examples

This example shows how to force a cluster to be the primary cluster:

switch-A# connect local-mgmt
Nexus 5000 Switch                                       
Cisco UCS 6100 Series Fabric Interconnect 

TAC support: http://www.cisco.com/tac 

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license. 
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html 
switch-A# cluster force primary
switch-A#                                    

Related Commands

Command	Description
show cluster
show file

cluster lead

To designate a cluster leader, use the cluster lead command.

cluster lead [ a | b ]

Syntax Description

a	Specifies switch A.
b	Specifies switch B.

Command Default

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The cluster commands are switch-specific local management commands. You must first execute a connect local-mgmt command to connect to the management port.

Examples

This example shows how to designate a cluster leader:

switch-A# connect local-mgmt
Nexus 5000 Switch                                       
Cisco UCS 6100 Series Fabric Interconnect 

TAC support: http://www.cisco.com/tac 

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license. 
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html 
switch-A# cluster lead b
switch-A#                                    

Related Commands

Command	Description
show cluster
show files

commit-buffer

To save or verify configuration changes, use the commit-buffer command.

commit-buffer [verify-only]

Syntax Description

verify-only

(Optional) Specifies verification only.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to execute all pending configuration changes. While any configuration commands are pending, an asterisk (*) appears before the command prompt. When you enter the commit-buffer command, the pending commands are committed and the asterisk disappears.

Examples

This example shows how to save configuration changes:

switch-A# create org 3
switch-A /org* # commit-buffer
switch-A /org #                                          
                                          

Related Commands

Command	Description
discard-buffer
show configuration pending

connect adapter

To connect to an adapter, use the connect adapter command.

connect adapter chassis-id/server-id/adapter-id

Syntax Description

chassis-id/server-id/adapter-id

Adapter identification number.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to connect to an adapter:

switch-A# connect adapter 1/1/1
adapter 1/1 #                                          
                                          

connect bmc

To connect to the BMC (Baseboard Management Controller), use the connect bmc command.

connect bmc chassis-id/blade-id

Syntax Description

chassis-id/blade-id

Chassis and blade identification numbers.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

The following example shows how to connect to the Baseboard Management Controller:

switch-A# connect bmc 1/1
Trying 127.5.1.1...                                          
Connected to 127.5.1.1.   
Escape character is '^]'.

NUOVA-IBMC login:

                                      

connect clp

To connect to DMTF CLP, use the connect clp command.

connect clp

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to connect to DMTF CLP:

switch-A# connect clp
/admin1 CLP ->

connect iom

To connect to an IO module, use the connect iom command.

connect iom id

Syntax Description

id	Chassis identification number. The valid range of values is 1 to 255.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to connect to a IO module:

switch-A# connect iom 1
Attaching to FEX 1 ...                                          
To exit type 'exit', to abort type '$.'  
fex-1#                                        

connect local-mgmt

To connect to the local management port, use the connect local-mgmt command.

connect local-mgmt [ a | b ]

Syntax Description

a	Specifies switch A.
b	Specifies switch B.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

If no switch is specified, a connection will be made to the local management port of the current active switch.

Examples

This example shows how to connect to the local management port of switch B:

switch-A# connect local-mgmt b
Cisco UCS 6100 Series Fabric Interconnect

TAC support: http://www.cisco.com/tac

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of 
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html
switch-B(local-mgmt)#

connect nxos

To connect to the NX-OS, use the connect nxos command.

connect nxos [a | b]

Syntax Description

a	(Optional) Specifies switch A.
b	(Optional) Specifies switch B.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to NXOS:

switch-A-A# connect nxos b
Nexus 5000 Switch                                       
Cisco UCS 6100 Series Fabric Interconnect 

TAC support: http://www.cisco.com/tac 

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license. 
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html 
switch-B#                                   

copy

To copy a file from one directory to another, use the copy command in local management command mode.

copy [from-filesystem:] [from-path] filename [to-filesystem:] to-path [dest-filename]

Syntax Description

from-filesystem:	File system containing the file to be copied. See the Usage Guidelines for valid values.
from-path	Absolute or relative path to the file to be copied.
filename	The name of the source file to be copied.
to-filesystem:	File system to contain the copied file. See the Usage Guidelines for valid values.
to-path	Absolute or relative path to the copied file.
dest-filename	(Optional) The new name for the copied file.

Command Default

None

Command Modes

Local management (local-mgmt)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to copy a file in local management command mode.

If a dest-filename is specified, the copied file is renamed at the destination location.

If no file system is specified, the current working file system is assumed. If no path is specified, the current working directory is assumed.

To specify the file system location, use the appropriate syntax from the following table:

ftp: [ // [ username@ ] server ]

scp: [ // [ username@ ] server ]

sftp: [ // [ username@ ] server ]

tftp: [ //server [ :port ] ]

volatile:

workspace:

Either the source or destination file system must be local; you cannot copy a file from one remote file system to another.

If a remote protocol is specified with no server name, you are prompted to enter the server name.

This command is available on the local management port command line. Use the connect local-mgmt command to connect to that command line.

This command operates on either the workspace (FLASH) or volatile (RAM) file system. To specify the file system, include the workspace: or volatile: keyword in the path. If the file system is not specified, the current working file system is assumed.

You can use the cp command as an alias for this command.

Examples

This example shows how to copy a file from the current working directory to a directory in the volatile file system:

switch-A # connect local-mgmt a
Cisco UCS 6100 Series Fabric Interconnect

TAC support: http://www.cisco.com/tac

Copyright (c) 2009, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software may be covered under the GNU Public
License or the GNU Lesser General Public License. A copy of 
each such license is available at
http://www.gnu.org/licenses/gpl.html and
http://www.gnu.org/licenses/lgpl.html

switch-A(local-mgmt)# copy abcdef.bin volatile:/temp
switch-A(local-mgmt)# 

Related Commands

Command	Description
connect local-mgmt

create adapter

To create an adapter, use the create adapter command.

create adapter

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create an adapter:

switch-A# scope org org3
switch-A /org # scope server-qual sq2                                       
switch-A /org/server-qual # create adapter
switch-A /org/server-qual/adapter* # commit-buffer 
switch-A /org/server-qual/adapter #                                      

Related Commands

Command	Description
show adapter
show chassis

create backup

To create a backup, use the create backup command.

create backup file { all-configuration | logical-configuration | system-configuration | full-state } { disabled | enabled }

Syntax Description

file	Managment file name. Use one of the following keywords for file type: ftp, scp, sftp, or tftp.
all-configuration	Specifies a server, fabric, and system-related configuration backup.
logical-configuration	Specifies a server and fabric backup.
system-configuration	Specifies a system-related configuration backup.
full-state	Specifies a full state backup for disaster recovery.
disabled	Specifies disabled.
enabled	Specifies enabled.

Command Default

None

Command Modes

System (/system)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

No more than one backup can be created and committed.

When you specify disabled, backup functionality is disabled. When you specify enabled, backup functionality is enabled.

Examples

This example shows how to create a backup:

switch-A# scope system
switch-A /system # create backup ftp: full-state enabled                                                            
Password:
switch-A /system/backup* # commit-buffer 
switch-A /system/backup #                                                            

Related Commands

Command	Description
show backup
show image

create bios-policy

To create a BIOS policy, use the create bios-policy command.

create bios-policy policy-name

Syntax Description

policy-name

Policy name. The name can contain up to 16 characters.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to create a BIOS policy and enter org BIOS policy mode.

Examples

The following example shows how to create a BIOS policy and enter org BIOS policy mode:

switch-A# scope org org3
switch-A /org # create bios-policy bios1
switch-A /org/bios-policy* # commit-buffer
switch-A /org/bios-policy #

Related Commands

Command	Description
show bios-policy

create block

To create a block, use the create block command.

IP pool configuration create block from to default-gw subnet-mask

WWN pool, UUID pool, and MAC pool configuration create block from to

Syntax Description

from	From address, identifier, or world-wide name. Specify a MAC address in the format NN:NN:NN:NN:NN:NN. Specify a UUID in the format NNNN-NNNNNNNNNNNN. Specify a WWN in the format HH:HH:HH:HH:HH:HH:HH:HH. Specify an IP address in the format A.B.C.D.
to	To address, identifier, or world-wide name. Specify a MAC address in the format NN:NN:NN:NN:NN:NN. Specify a UUID in the format NNNN-NNNNNNNNNNNN. Specify a WWN in the format HH:HH:HH:HH:HH:HH:HH:HH. Specify an IP address in the format A.B.C.D.
default-gw	Default gateway.
subnet-mask	Subnet mask.

Command Default

None

Command Modes

IP pool (/org/ip-pool)

WWN pool (/org/wwn-pool)

UUID suffix pool (/org/uuid-suffix-pool)

MAC pool (/org/mac-pool)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create addresses, identifiers, and world-wide names.

Use IP pool configuration mode to create IP address blocks. Use WWN pool, UUID pool, and MAC pool configuration mode to create addresses, UUIDs, and WWNs.

Examples

This example shows how to create a block:

switch-A# scope org org3
switch-A /org # scope mac-pool mp1                                                   
switch-A /org/mac-pool # create block 1a:2b:3c:4d:21:31 1b:2a:3c:4d:21:31  
switch-A /org/mac-pool* # commit-buffer
switch-A /org/mac-pool #                                                  

Related Commands

Command	Description
show mac-pool
show pooled

create boot-definition

To create a boot definition, use the create boot-definition command.

create boot-definition

This command has no arguments or keywords.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a boot definition:

switch-A# scope org org3
switch-A /org # scope service-profile sp1                                       
switch-A /org/service-profile # create boot-definition   
switch-A /org/service-profile/boot-definition* # commit-buffer
switch-A /org/service-profile/boot-definition #                                     

Related Commands

Command	Description
show boot-definition
show lan

create boot-policy

To create a boot policy, use the create boot-policy command.

create boot-policy name purpose { operational | utility } *

Syntax Description

name	Policy name. The range of valid values is 1 to 16.
purpose	Specifies the purpose of the policy.
operational	Specifies an operational policy.
utility	Specifies a utility policy.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a boot policy:

switch-A# scope org org3
switch-A /org # create boot-policy boot1                                                   
switch-A /org/boot-policy* #commit-buffer 
switch-A /org/boot-policy #                                                  

Related Commands

Command	Description
show lan
show virtual-media

create cap-qual

To create a capacity qualification, use the create cap-qual command.

create cap-qual { fcoe | non-virtualized-eth-if | non-virtualized-fc-if | path-encap-consolidated | path-encap-virtual | protected-eth-if | protected-fc-if | protected-fcoe | virtualized-eth-if | virtualized-fc-if | virtualized-scsi-if }

Syntax Description

fcoe	Specifies Fibre Channel over Ethernet.
non-virtualized-eth-if	Specifies non-virtualized Ethernet interface.
non-virtualized-fc-if	Specifies non-virtualized Fibre Channel interface.
path-encap-consolidated	Specifies path encapsulation consolidated.
path-encap-virtual	Specifies path encapsulation virtual.
protected-eth-if	Specifies protected Ethernet interface.
protected-fc-if	Specifies protected Fibre Channel interface.
protected-fcoe	Specifies protected Fibre Channel over Ethernet.
virtualized-eth-if	Specifies virtualized Ethernet interface.
virtualized-fc-if	Specifies virtualized Fibre Channel interface.
virtualized-scsi-if	Specifies virtualized SCSI interface.

Command Default

None

Command Modes

Adapter (/org/server-qual/adapter)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Creates an adapter capacity qualification for the specified adapter type and enters organization server qualification adapter mode.

Examples

This example shows how to create a capacity qualification:

switch-A# scope org org3
switch-A /org # scope server-qual sq2
switch-A /org/server-qual # scope adapter 1/1/1
switch-A /org/server-qual/adapter # create cap-qual cq10
switch-A /org/server-qual/adapter* # commit-buffer
switch-A /org/server-qual/adapter # 

Related Commands

Command	Description
show adapter
show server-qual

create certreq

To create a keyring certificate request, use the create certreq command.

create certreq { subject-name name | ip ip-address } + [ password password ]

Syntax Description

subject-name	Specifies subject name.
name	Subject name. The range of valid values is 1 to 16.
ip	Specifies IP address.
ip-address	IP address. The format is A.B.C.D.
password	(Optional) Specifies password.
password	Password. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Keyring (/security/keyring)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Before you create a certreq you must set modulus.

Examples

This example shows how to create a keyring certificate request:

switch-A# scope security
switch-A /security # scope keyring k1                                                
switch-A /security/keyring # create certreq subject-name cr3
switch-A /security/keyring* # commit-buffer 
switch-A /security/keyring #                                                

Related Commands

Command	Description
show certreq
show keyring

create chassis

To create a chassis, use the create chassis command.

create chassis min-id max-id

Syntax Description

min-id	Minimum chassis identification number. The range of valid values is 1 to 255.
max-id	Maximum chassis identification number. The range of valid values is 1 to 255.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Creates a chassis with the specified name, and enters organization chassis mode.

Examples

This example shows how to create a chassis:

switch-A# scope org org3
switch-A /org # scope server-qual sq2                                             
switch-A /org/server-qual # create chassis 2 2
switch-A /org/server-qual/chassis* # commit-buffer 
switch-A /org/server-qual/chassis #                                             

Related Commands

Command	Description
show chassis
show server

create class chassis-stats

To create a chassis statistics class, use the create class chassis-stats command.

create class chassis-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for chassis statistics.

Examples

This example shows how to create a chassis statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy tp10                                       
switch-A /eth-server/stats-threshold-policy # create class chassis-stats
switch-A /eth-server/stats-threshold-policy* # commit-buffer
switch-A /eth-server/stats-threshold-policy #                                       

Related Commands

Command	Description
show chassis
show class

create class cmc-stats

To create a CMC statistics class, use the create class cmc-stats command.

create class cmc-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for CMC statistics.

Examples

This example shows how to create a chassis statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy tp10                                       
switch-A /eth-server/stats-threshold-policy # create class cmc-stats
switch-A /eth-server/stats-threshold-policy* # commit-buffer
switch-A /eth-server/stats-threshold-policy #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class cpu-env-stats

To create the CPU environment statistics class, use the create class cpu-env-stats command.

create class cpu-env-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

When you create the class, you enter organization statistics threshold policy CPU environment class mode. You can then create properties for this class with the create property command in the mode.

Examples

This example shows how to create a CPU environment statistics class:

switch-A# scope org org100
switch-A /org # scope stats-threshold-policy stp100                                       
switch-A /org/stats-threshold-policy # create class cpu-env-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class dimm-stats

To create a DIMM statistics class, use the create class dimm-stats command.

create class dimm-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for DIMMs.

Examples

This example shows how to create a DIMM statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p1                                       
switch-A /org/stats-threshold-policy # create class dimm-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ether-error-stats

To create an Ethernet error statistics class, use the create class ether-error-stats command.

create class ether-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy under Ethernet uplink (/eth-uplink/stats-threshold-policy)

Statistics threshold policy under Ethernet server (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet error statistics.

Examples

This example shows how to create an Ethernet error statistics class:

switch-A# scope eth-uplink
switch-A /eth-uplink # scope stats-threshold-policy p10                                       
switch-A /eth-uplink/stats-threshold-policy # create class ether-error-stats 
switch-A /eth-uplink/stats-threshold-policy* # commit-buffer 
switch-A /eth-uplink/stats-threshold-policy #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ether-if-stats

To create an Ethernet interface statistics class, use the create class ether-if-stats command.

create class ether-if-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet interface statistics.

Examples

This example shows how to create an Ethernet interface statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p1                                       
switch-A /org/stats-threshold-policy # create class ether-if-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ether-loss-stats

To create an Ethernet loss statistics class, use the create class ether-loss-stats command.

create class ether-loss-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy under Ethernet server (/eth-server/stats-threshold-policy)

Statistics threshold policy under Ethernet uplink (/eth-uplink/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet loss statistics.

Examples

This example shows how to create an Ethernet loss statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class ether-loss-stats
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer
switch-A /eth-server/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-err-stats

To create an Ethernet port error statistics class, use the create class ethernet-port-err-stats command.

create class ethernet-port-err-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port error statistics.

Examples

This example shows how to create an Ethernet port error statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-err-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-multicast-stats

To create an Ethernet port multicast statistics class, use the create class ethernet-port-multicast-stats command.

create class ethernet-port-multicast-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port multicast statistics.

Examples

This example shows how to create an Ethernet port multicast statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-multicast-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-over-under-sized-stats

To create an Ethernet port over-under-sized statistics class, use the create class ethernet-port-over-under-sized-stats command.

create class ethernet-port-over-under-sized-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port over-under-sized statistics.

Examples

This example shows how to create an Ethernet port statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-over-under-sized-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-stats

To create an Ethernet port statistics class, use the create class ethernet-port-stats command.

create class ethernet-port-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port statistics.

Examples

This example shows how to create an Ethernet port statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-stats-by-size-large-packets

To create an Ethernet port large packet statistics class, use the create class ethernet-port-stats-by-size-large-packets command.

create class ethernet-port-stats-by-size-large-packets

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port small packet statistics.

Examples

This example shows how to create an Ethernet port large packet statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-stats-by-size-large-packets  
switch-A /org/stats-threshold-policy/class* # commit-buffer
swicth-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ethernet-port-stats-by-size-small-packets

To create an Ethernet port small packet statistics class, use the create class ethernet-port-stats-by-size-small-packets command.

create class ethernet-port-stats-by-size-small-packets

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet port small packet statistics.

Examples

This example shows how to create an Ethernet port small packet statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class ethernet-port-stats-by-size-small-packets  
switch-A /org/stats-threshold-policy/class* # commit-buffer
swicth-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class ether-rx-stats

To create an Ethernet recieve statistics class, use the create class ether-rx-stats command.

create class ether-rx-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy under Ethernet server (/eth-server/stats-threshold-policy)

Statistics threshold policy under Ethernet uplink (/eth-uplink/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet recieve statistics.

Examples

This example shows how to create an Ethernet recieve statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class eth-rx-stats
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer
switch-A /eth-server/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show eth-uplink
show stats-threshold-policy

create class ether-tx-stats

To create an Ethernet transmission statistics class, use the create class ether-tx-stats command.

create class ether-tx-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy under Ethernet uplink (/eth-uplink/stats-threshold-policy)

Statistics threshold policy under Ethernet server (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place a threshold on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Ethernet transmission statistics.

Examples

This example shows how to create an Ethernet transmission statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class eth-tx-stats
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer
switch-A /eth-server/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show eth-uplink
show stats-threshold-policy

create class fan-module-stats

To create a fan module statistics class, use the create class fan-module-stats command.

create class fan-module-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for fan module statistics.

Examples

This example shows how to create a fan module statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class fan-module-stats 
switch-A /eth-server/stats-threshold-policy* # commit-buffer 
switch-A /eth-server/stats-threshold-policy #                                      

Related Commands

Command	Description
show fan-module
show stats-threshold-policy

create class fan-stats

To create a fan statistics class, use the create class fan-stats command.

create class fan-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to place thresholds on statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for fan statistics.

Examples

This example shows how to create a fan statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class fan-stats 
switch-A /eth-server/stats-threshold-policy* # commit-buffer 
switch-A /eth-server/stats-threshold-policy #                                      

Related Commands

Command	Description
show fan-module
show stats-threshold-policy

create class fc-error-stats

To create a Fibre Channel error statistics class, use the create class fc-error-stats command.

create class fc-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy /fc-uplink/stats-threshold-policy

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel error statistics.

Examples

This example shows how to create a Fibre Channel error statistics class:

switch-A# scope fc-uplink
switch-A /org # scope stats-threshold-policy p10                                       
Pubs-A /org/stats-threshold-policy # create class fc-error-stats
Pubs-A /org/stats-threshold-policy/class* # commit-buffer 
Pubs-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class fc-if-event-stats

To create Fibre Channel event statistics, use the create class fc-if-event-stats command.

create class fc-if-event-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel event statistics.

Examples

The following example

switch-A # scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class fc-if-event-stats 
switch-A /org/stats-threshold-policy* # commit-buffer
switch-A /org/stats-threshold-policy #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class fc-if-fc4-counters

To create Fibre Channel counters, use the create class fc-if-fc4-counters command.

create class fc-if-fc4-counters

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel counter statistics.

Examples

This example shows how to create Fibre Channel counters:

switch-A # scope org org3
switch-A /org # switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class fc-if-fc4-stats  
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class fc-if-frame-stats

To create a Fibre Channel frame statistics class, use the create class fc-if-frame-stats command.

create class fc-if-frame-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel frame statistics.

Examples

This example shows how to create a Fibre Channel frame statistics class:

switch-A # scope org org3
switch-A /org # switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class fc-if-frame-stats  
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class fc-port-stats

To create Fibre Channel port statistics class, use the create class fc-port-stats command.

create class fc-port-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel port statistics.

Examples

This example shows how to create a Fibre Channel port statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class fc-port-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show class
show stats-threshold-policy

create class fc-stats

To create a Fibre Channel statistics class, use the create class fc-stats command.

create class fc-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/fc-uplink/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Fibre Channel statistics.

Examples

This example shows how to create a Fibre Channel statistics class:

switch-A# scope fc-uplink
switch-A /fc-uplink # scope stats-threshold-policy p10                                       
switch-A /fc-uplink/stats-threshold-policy # create class fc-stats
switch-A /fc-uplink/stats-threshold-policy/class* # commit-buffer
switch-A /fc-uplink/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show class
show stats-threshold-policy

create class mb-power-stats

To create a mother board power statistics class, use the create class mb-power-stats command.

create class mb-power-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for mother board power statistics.

Examples

This example shows how to create a mother board power statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class mb-power-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                        

Related Commands

Command	Description
show class
show stats-threshold-policy

create class mb-temp-stats

To create a temporary mother board statistics class, use the create class mb-temp-stats command.

create class mb-temp-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Mb statistics.

Examples

This example shows how to create a temporary mother board statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class mb-temp-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show class mb-temp-stats

create class memory-runtime

To create a memory runtime class, use the create class memory-runtime command.

create class memory-runtime

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a memory runtime class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class memory-runtime 
switch-A /org/stats-threshold-policy* # commit-buffer 
switch-A /org/stats-threshold-policy #                                      

Related Commands

Command	Description
show class
show memory

create class menlo-dce-port-stats

To create a Menlo port statistics class, use the create class menlo-dce-port-stats command.

create class menlo-dce-port-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Ethernet port statistics.

Examples

This example shows how to create a Menlo port statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-dce-port-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-eth-error-stats

To create a Menlo Ethernet error statistics class, use the create class menlo-eth-error-stats command.

create class menlo-eth-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Ethernet error statistics.

Examples

This example shows how to create a Menlo Ethernet error statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-eth-error-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-eth-stats

To create a Menlo Ethernet statistics class, use the create class menlo-eth-stats command.

create class menlo-eth-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Ethernet statistics.

Examples

This example shows how to create a Menlo Ethernet statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-eth-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                      

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-fc-error-stats

To create Menlo Fibre Channel error statistics, use the create class menlo-fc-error-stats command.

create class menlo-fc-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Fibre Channel error statistics.

Examples

This example shows how to create Menlo Fibre Channel error statistics:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-fc-error-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-fc-stats

To create Menlo Fibre Channel statistics, use the create class menlo-fc-stats command.

create class menlo-fc-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Fibre Channel statistics.

Examples

This example shows how to create Menlo Fibre Channel statistics:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-fc-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-host-port-stats

To create Menlo host port statistics, use the create class menlo-host-port-stats command.

create class menlo-host-port-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo host port statistics.

Examples

This example shows how to create Menlo host port statistics:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-host-port-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-mcpu-error-stats

To create a Menlo CPU error statistics class, use the create class menlo-mcpu-error-stats command.

create class menlo-mcpu-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo CPU error statistics.

Examples

This example shows how to create a Menlo CPU error statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-mcpu-error-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-mcpu-stats

To create a Menlo CPU statistics class, use the create class menlo-mcpu-stats command.

create class menlo-mcpu-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo CPU statistics.

Examples

This example shows how to create a Menlo CPU statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-mcpu-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                     

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-net-eg-stats

To create a Menlo network egress statistics class, use the create class menlo-net-eg-stats command.

create class menlo-net-eg-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo network egress traffic statistics.

Examples

This example shows how to create a Menlo network egress statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-net-eg-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-net-in-stats

To create a Menlo network ingress statistics class, use the create class menlo-net-in-stats command.

create class menlo-net-in-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo network ingress traffic statistics.

Examples

This example shows how to create a Menlo network ingress statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-net-in-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-q-error-stats

To create a Menlo Qlogic error statistics class, use the create class menlo-q-error-stats command.

create class menlo-q-error-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Qlogic error statistics.

Examples

This example shows how to create a Menlo Qlogic error statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-q-error-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class menlo-q-stats

To create a Menlo Qlogic statistics class, use the create class menlo-q-stats command.

create class menlo-q-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Menlo Qlogic statistics.

Examples

This example shows how to create a Menlo Qlogic statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class menlo-q-stats
switch-A /org/stats-threshold-policy/class* # commit-buffer
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-policy

create class processor-runtime

To create a processor runtime statistics class, use the create class processor-runtime command.

create class processor-runtime

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a processor runtime statistics class:

switch-A# scope org org10
switch-A /org # scope stats-threshold-policy p10                                       
switch-A /org/stats-threshold-policy # create class processor-runtime
switch-A /org/stats-threshold-policy/class* # commit-buffer 
switch-A /org/stats-threshold-policy/class #                                       

Related Commands

Command	Description
show class
show stats-threshold-statistics

create class psu-input-stats

To create a power supply input statistics class, use the create class psu-input-stats command.

create class psu-input-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for power supply input statistics.

Examples

This example shows how to create a power supply input statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class psu-input-stats 
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer  
switch-A /eth-server/stats-threshold-policy/class #                                    

Related Commands

Command	Description
show class
show stats-threshold-policy

create class psu-stats

To create a power supply statistics class, use the create class psu-stats command.

create class psu-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for power supply statistics.

Examples

This example shows how to create power supply statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class psu-stats 
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer  
switch-A /eth-server/stats-threshold-policy/class #                                    

Related Commands

Command	Description
show class
show stats-threshold-policy

create class system-stats

To create a system statistics class, use the create class system-stats command.

create class system-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/eth-server/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for system statistics.

Examples

This example shows how to create a system statistics class:

switch-A# scope eth-server
switch-A /eth-server # scope stats-threshold-policy p10                                       
switch-A /eth-server/stats-threshold-policy # create class system-stats 
switch-A /eth-server/stats-threshold-policy/class* # commit-buffer  
switch-A /eth-server/stats-threshold-policy/class #                                    

Related Commands

Command	Description
show class
show system

create client

To create a client, use the create client command in port-profile mode.

create client client-name

Syntax Description

client-name

The name of the client. A unique set of numbers or letters that identifies the client. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Profile set (/system/vm-mgmt/vmware/profile-set/port-profile)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Creates a client for a port profile. It also enters you into system VM management VMware profile set port profile mode. This command is used along with other commands to configure port profiles.

Examples

This example shows how to create a client:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope profile-set
switch-A /system/vm-mgmt/vmware/profile-set # scope port-profile pp100
switch-A /system/vm-mgmt/vmware/profile-set/port-profile # create client c100
switch-A /system/vm-mgmt/vmware/profile-set/port-profile* # commit-buffer
switch-A /system/vm-mgmt/vmware/profile-set/port-profile #                                      

Related Commands

Command	Description
show port profile
show profile-set

create class vnic-stats

To create a Virtual NIC statistics class, use the create class vnic-stats command.

create class vnic-stats

This command has no arguments or keywords.

Command Default

None

Command Modes

Statistics threshold policy (/org/stats-threshold-policy)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use classes to threshold statistics. For example, you might want to define a threshold on a port that raises a fault if the average number of packets dropped exceeds a certain amount. For this class, you would create thresholds for Virtual NIC statistics.

Examples

This example shows how to create a Virtual NIC statistics class:

switch-A# scope org org3
switch-A /org # scope stats-threshold-policy p1                                       
switch-A /org/stats-threshold-policy # create class vnic-stats 
switch-A /org/stats-threshold-policy/class* # commit-buffer  
switch-A /org/stats-threshold-policy/class #                                    

Related Commands

Command	Description
show class
show vnic-templ

create cpu

To create a CPU qualifier for a server pool policy, use the create cpu command.

create cpu

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command create a CPU qualifier for a server pool policy, and to enter organization CPU mode.

Only one CPU qualifier can be created.

Examples

This example shows how to create a CPU qualifier:

switch# scope org org3
switch /org # scope server-qual sq20
switch /org/server-qual # create cpu
switch /org/server-qual/cpu* # commit-buffer 
switch /org/server-qual/cpu #

Related Commands

Command	Description
show cpu
show server-qual

create data-center

To create a data center, use the create data-center command in vcenter mode. You can also create a data center in folder mode.

create data-center datacenter-name

Syntax Description

datacenter-name

The name of the data center. A unique set of numbers or letters that identifies the data center. The range of valid values is 1 to 16.

Command Default

None

Command Modes

VCenter (/system/vm-mgmt/vmware/vcenter)

Folder (/system/vm-mgmt/vmware/vcenter/folder

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Data center

Examples

This example shows how to create a data center:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope vcenter
switch-A /system/vm-mgmt/vmware/vcenter # create data-center dc10
switch-A /system/vm-mgmt/vmware/vcenter* # commit-buffer
switch-A /system/vm-mgmt/vmware/vcenter #                                      

Related Commands

Command	Description
show data-center
show folder

create default-behavior

To create a default behavior mode, use the create default-behavior command.

create default-behavior { vhba | | vnic }

Syntax Description

vhba	Specifies vHBA default behavior mode.
vnic	Specifies vNIC default behavior mode.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Use this command to create a default behavior, and enter organization default-behavior mode.

hw-inherit sets

Examples

This example shows how to create a vNIC default behavior mode:

switch-A# scope org org10
switch-A /org # scope service-profile sp10 
switch-A /org/service-profile # create default-behavior vnic
switch-A /org/service-profile/default-behavior* # commit-buffer
switch-A /org/service-profile/default-behavior #                                          

Related Commands

Command	Description
show default-behavior
show vnic

create destination

To create an email destination, use the create destination command.

create destination email

Syntax Description

email

Email destination.

Command Default

None

Command Modes

Profile (/monitoring/callhome/profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create an email destination:

switch-A# scope monitoring
switch-A /monitoring # scope callhome                                          
switch-A /monitoring/callhome # scope profile p3
switch-A /monitoring/callhome/profile # create destination home@test.com
switch-A /monitoring/callhome/profile* # commit-buffer 
switch-A /monitoring/callhome/profile #                                          

Related Commands

Command	Description
show callhome
show destination

create distributed-virtual-switch

To create a distributed virtual switch, use the create distributed-virtual-switch command in folder mode.

create distributed-virtual-switch dvs-name

Syntax Description

dvs-name

The name of the switch. A unique set of numbers or letters that identifies the switch. The range of valid values is 1 to 16.

Command Default

• Admin State is disabled

• UUID is 00000000-0000-0000-0000-000000000000

• Extension key is blank

Command Modes

VMware (/system/vm-mgmt/vmware/vcenter/data-center/folder)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Distributed virtual switch

Examples

This example shows how to create a distributed virtual switch:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope vcenter vc10
switch-A /system/vm-mgmt/vmware/vcenter # scope data-center dc10
switch-A /system/vm-mgmt/vmware/vcenter/data-center # scope folder f10
switch-A /system/vm-mgmt/vmware/vcenter/data-center/folder # create distributed-virtual-switch dvs10
switch-A /system/vm-mgmt/vmware/vcenter/data-center/folder* # commit-buffer
switch-A /system/vm-mgmt/vmware/vcenter/data-center/folder #                                      

Related Commands

Command	Description
show distributed-virtual-switch
show folder

create dns

To create a DNS host name , use the create dns command.

create dns name

Syntax Description

name	DNS host name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Services (/system/services)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a DNS host name:

switch-A# scope system
switch-A /system # scope services                                          
switch-A /system/services # create dns dns10  
switch-A /system/services* # commit-buffer
switch-A /system/services #                                        

Related Commands

Command	Description
show dns
show ntp

create dynamic-vnic-conn

To create a dynamic vNIC connection, use the create dynamic-vnic-conn command.

create dynamic-vnic-conn

This command has no arguments or keywords.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

The vNIC connection policy determines how the VN-link connectivity between VMs and dynamic vNICs is configured. This policy is required for Cisco UCS instances that include servers with Cisco M81KR VIC adapters that host VMs and dynamic vNICs.

Each Dynamic vNIC connection policy must include an adapter policy and designate the number of vNICs that can be configured for any server associated with a service profile that includes the policy.

Examples

This example shows how to create a dynamic vNIC connection:

switch-A# scope org org10
switch-A /org # scope service-profile sp10
switch-A /org/service-profile # create dynamic-vnic-conn                                                   
switch-A /org/service-profile* # commit-buffer 
switch-A /org/service-profile #                                                  

Related Commands

Command	Description
show dynamic-vnic-con
show dynamic-vnic-con-policy

create dynamic-vnic-conn-policy

To create a dynamic vNIC connection policy, use the create dynamic-vnic-conn-policy command.

create dynamic-vnic-conn-policy policy-name

Syntax Description

policy-name

The name of the vNIC connection policy. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The vNIC connection policy determines how the VN-link connectivity between VMs and dynamic vNICs is configured. This policy is required for Cisco UCS instances that include servers with Cisco M81KR VIC adapters that host VMs and dynamic vNICs.

Each Dynamic vNIC connection policy must include an adapter policy and designate the number of vNICs that can be configured for any server associated with a service profile that includes the policy.

Examples

This example shows how to create a dynamic VNIC connection policy:

switch-A# scope org org10
switch-A /org # create dynamic-vnic-conn-policy dvcp10                                                   
switch-A /org/dynamic-vnic-conn-policy* # commit-buffer 
switch-A /org/dynamic-vnic-conn-policy #                                                  

Related Commands

Command	Description
show dynamic-vnic-connection-policy
show vnic-templ

create egress-policy

To create an egress policy, use the create data-center command in vcenter mode. You can also create a data center in folder mode.

create egress-policy policy-name

Syntax Description

policy-name

The name of the policy. A unique set of numbers or letters that identifies the policy. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Egress policy (/org/qos-policy/egress-policy)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Data center

Examples

This example shows how to create a data center:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope vcenter
switch-A /system/vm-mgmt/vmware/vcenter # create data-center dc10
switch-A /system/vm-mgmt/vmware/vcenter* # commit-buffer
switch-A /system/vm-mgmt/vmware/vcenter #                                      

Related Commands

Command	Description
show data-center
show folder

create epuser

To create an end-point user, use the create epuser command.

create epuser name

Syntax Description

name	End-point user name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

IPMI access profile (/org/ipmi-access-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Creates the specified endpoint user and enters organization IPMI access profile endpoint user mode.

More than one endpoint user can be created within an IPMI access profile, with each endpoint user having its own password and privileges

Examples

This example shows how to create an end-point user:

switch-A# scope org org10
switch-A /org # scope ipmi-access-profile ap10                                          
switch-A /org/ipmi-access-profile # create epuser user10 
switch-A /org/ipmi-access-profile/epuser* # commit-buffer
switch-A /org/ipmi-access-profile/epuser #                                         

Related Commands

Command	Description
show epuser
show ipmi-access-profile

create eth-if

To create an Ethernet interface, use the create eth-if command.

create eth-if name

Syntax Description

name	Interface name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Virtual NIC (/org/service-profile/vnic)

Virtual NIC template (/org/vnic-templ)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create an Ethernet interface:

switch-A# scope org org10
switch-A /org # scope service-profile sp10                                          
switch-A /org/service-profile # scope vnic vn10 
switch-A /org/service-profile/vnic # create eth-if if10
switch-A /org/service-profile/vnic/eth-if* # commit-buffer
switch-A /org/service-profile/vnic/eth-if #                                         

Related Commands

Command	Description
show eth-profile
show service-profile

create eth-policy

To create an Ethernet policy, use the create eth-policy command.

create eth-policy name

Syntax Description

policy-name

The name of the Ethernet policy. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create Ethernet policy ep100 in org100 mode:

switch-A# scope org org100
switch-A /org # create eth-policy ep100                                          
switch-A /org/eth-policy* # commit-buffer 
switch-A /org/eth-policy #                                         

Related Commands

Command	Description
show eth-policy
show trans-queue

create fcoe-if

To create a FCoE (Fibre Channel over Ethernet) interface, use the create fcoe-if command.

create fcoe-if

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual NIC (/org/service-profile/vnic)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create an FCoE interface:

switch# scope org org3
switch /org # scope service-profile sp1                                       
switch /org/service-profile # scope vnic 
switch /org/service-profile/vnic # create fcoe-if
switch /org/service-profile/vnic* # commit-buffer  
switch /org/service-profile/vnic #                                   

Related Commands

Command	Description
show interface
show vnic

create fc-policy

To create a Fibre Channel policy, use the create fc-policy command.

create fc-policy policy-name

Syntax Description

policy-name

The name of the Fibre Channel policy. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a Fibre Channel policy, and enter organization fc-policy mode.

Examples

This example shows how to create Fibre Channel policy fcp10 in org10 mode:

switch# scope org org10
switch /org # create fc-policy fcp10                                          
switch /org/fc-policy* # commit-buffer 
switch /org/fc-policy #                                          

Related Commands

Command	Description
show fc-policy
show trans-queue

create folder

To create a folder, use the create folder command in vcenter mode. You can also create a folder in data-center mode.

create folder folder-name

Syntax Description

folder-name

The name of the folder. A unique set of numbers or letters that identifies the folder. The range of valid values is 1 to 16.

Command Default

None

Command Modes

VCenter (/system/vm-mgmt/vmware/vcenter)

Folder (/system/vm-mgmt/vmware/vcenter/data-center

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Folder

Examples

This example shows how to create a folder:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope vcenter
switch-A /system/vm-mgmt/vmware/vcenter # create folder folder10
switch-A /system/vm-mgmt/vmware/vcenter* # commit-buffer
switch-A /system/vm-mgmt/vmware/vcenter #                                      

Related Commands

Command	Description
show folder
show vcenter

create fw-host-pack

To create a host pack, use the create fw-host-pack command.

create fw-host-pack name

Syntax Description

name	Pack name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

A pack is a collection of host firwmare images for devices like adapters, HBAs, NICs, and raid controllers.

Use this command to create a host firmware package and enter organization firmware host package mode.

Examples

This example shows how to create a host pack:

switch-A# scope org org3
Pubs-A /org # create fw-host-pack hp4                                          
Pubs-A /org/fw-host-pack* # commit-buffer  
Pubs-A /org/fw-host-pack #                                        

Related Commands

Command	Description
show fw- host-pack
show fw-mgmt-pack

create fw-mgmt-pack

To create a management pack, use the create fw-mgmt-pack command.

create fw-mgmt-pack name

Syntax Description

name	Pack name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

A pack is a collection of host firwmare images for devices like adapters, HBAs, NICs, and raid controllers.

Use this command to create a management firmware package and enter organization firmware management package mode.

Examples

This example shows how to create a management pack:

switch# scope org org3
switch /org # create fw-mgmt-pack mp4                                          
switch /org/fw-host-pack* # commit-buffer  
switch /org/fw-host-pack #                                        

Related Commands

Command	Description
show fw- host-pack
show fw-mgmt-pack

create hv-conn

To create an HV connection, use the create hv-conn command.

create hv-conn protection { none | protected } *

Syntax Description

protection	Specifies that the connection is protected.
none	Specifies no protection.
protected	Specifies protection.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a Hypervisor connection, and enter organization HV connection mode.

Examples

This example shows how to create a HV connection:

switch# scope org org3
switch /org # scope service-profile sp1                                                
switch /org/service-profile # create hv-conn
switch /org/service-profile/hv-conn* # commit-buffer
switch /org/service-profile/hv-conn #                                                

Related Commands

Command	Description
show connectivity
show hv-conn

create import-config

To create a import configuration, use the create import-config command.

create import-config { ftp: | scp: | sftp: | tftp: } { disabled | enabled } { merge | replace }

Syntax Description

ftp:	Specifies File Transfer Protocol.
scp:	Specifies Secure Copy Protocol.
sftp:	Specifies Secure File Transfer Protocol.
tftp:	Specifies Trivial File Transfer Protocol.
disabled	Specifies disabled.
enabled	Specifies enabled.
merge	Specifies merge.
replace	Specifies replace.

Command Default

None

Command Modes

System (/system)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a configuration for importing files, and enter organization import configuration mode.

Examples

This example shows how to create an import configuration:

switch# scope system
switch /system # create import-config ftp: enabled replace                                       
switch /service/import-config* # commit-buffer 
switch /service/import-config #                                   

Related Commands

Command	Description
show image
show import-config

create initiator

To create an initiator, use the create initiator command.

create initiator id

Syntax Description

id	Initiator identification number. The range of valid values is 1 to 16.

Command Default

None

Command Modes

WWN pool (/org/wwn-pool)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a WWN initiator, and enter organization initiator mode.

Examples

This example shows how to create an initiator:

switch-A# scope org org3
switch-A /org # scope wwn-pool wwnpool3                                          
switch-A /org/wwn-pool # create initiator 
switch-A /org/wwn-pool/initiator* # commit-buffer
switch-A /org/wwn-pool/initiator #                                           

Related Commands

Command	Description
show block
show initiator

create interface

To create an interface, use the create interface command.

create interface slot-id port-id

Syntax Description

slot-id	Slot identification number. The range of valid values is 2 to 5.
port-id	Port identification number. The range of valid values is 1 to 40.

Command Default

None

Command Modes

Fabric interconnect under Fibre Channel uplink (/fc-uplink/fabric)

Fabric interconnect under Ethernet server (/eth-server/fabric)

Fabric interconnect under Ethernet uplink (/eth-uplink/fabric)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create an Ethernet or Fibre Channel interface, and enter organization interface mode.

Examples

This example shows how to create an interface:

switch# scope fc-uplink
switch /fc-uplink # scope switch b                                       
switch /fc-uplink/switch # create interface 5 10 
switch /fc-uplink/switch/interface* # commit-buffer
switch /fc-uplink/switch/interface #                                       

Related Commands

Command	Description
show interface
show switch

create ipmi-access-profile

To create an IPMI (Intelligent Platform Management Interface) access profile, use the create ipmi-access-profile command.

create ipmi-access-profile name

Syntax Description

name	IPMI access profile name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create an IPMI access profile, and enter organization IPMI access profile mode.

Examples

This example shows how to create an IPMI access profile:

switch# scope org org3
switch /org # create ipmi-access-profile ipmiProf1                                          
switch /org/ipmi-access-profile* # commit-buffer
switch /org/ipmi-access-profile #                                           

Related Commands

Command	Description
show epuser
show ipmi-access-profile

create keyring

To create a keyring, use the create keyring command.

create keyring name

Syntax Description

name	Keyring name. The name can be up to 16 alphanumeric characters.

Command Default

None

Command Modes

Security (/security)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a keyring to store RSA keys, and enter organization keyring mode.

Examples

This example shows how to create a keyring:

switch# scope security
switch /security # create keyring kr220
switch /security/keyring* # commit-buffer
switch /security/keyring #

Related Commands

Command	Description
show keyring

create lan

To create a LAN, use the create lan command.

create lan

This command has no arguments or keywords.

Command Default

None

Command Modes

Boot policy under organization (/org/boot-policy)

Boot definition under service-profile (/org/service-profile/boot-def)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a LAN, and enter organization lan mode.

Examples

This example shows how to create a LAN:

switch-A# scope org org3
switch-A /org # scope boot-policy bp6                                       
switch-A /org/boot-policy # create lan 
switch-A /org/boot-policy/lan* # commit-buffer
switch-A /org/boot-policy/lan #                                       

Related Commands

Command	Description
show boot-policy
show lan

create local

To create local storage, use the create local command.

create local

Command Default

None

Command Modes

Storage (/org/boot-policy/storage)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create local storage:

switch# scope org org10
switch /org # scope boot-policy bp10                                       
switch /org/boot-policy # scope storage 
switch /org/boot-policy/storage # create local storage10
switch /org/boot-policy/storage* # commit-buffer 
switch /org/boot-policy/storage #                                      

Related Commands

Command	Description
show local
show storage

create local-disk-config

To create a local disk configuration, use the create local-disk-config command.

create local-disk-config

This command has no arguments or keywords.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a local disk configuration, and enter organization local disk configuration mode.

Examples

This example shows how to create a local disk configuration:

switch# scope org org3
switch /org # scope service-profile sp1                                       
switch /org/service-profile # create local-disk-config 
switch /org/service-profile/local-disk-config* # commit-buffer
switch /org/service-profile/local-disk-config #                                      

Related Commands

Command	Description
show local-disk-config
show local-disk-config-policy

create local-disk-config-policy

To create a local disk configuration policy, use the create local-disk-config-policy command.

create local-disk-config-policy name

Syntax Description

name	Local disk configuration policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a local disk configuration policy, and enter organization local disk configuration policy mode.

Examples

This example shows how to create a local disk configuration policy:

switch# scope org org3
switch /org # create local-disk-config-policy ldcp1                                       
switch /org/local-disk-config-policy* # commit-buffer 
Pubs-A /org/local-disk-config-policy #                                       

Related Commands

Command	Description
show local-disk-config
show local-disk-config-policy

create locale

To create a locale, use the create locale command.

create locale name

Syntax Description

name	Locale name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Local user (/security/local-user)

Security (/security)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a locale, and enter organization local user mode.

Examples

This example shows how to create a locale:

switch# scope security
switch /security # scope local-user lu1
switch /security # create locale locale1
switch /security/local-user* # commit-buffer                                          
switch /security/local-user #                                           

Related Commands

Command	Description
show locale
show local-user

create local-user

To create a local user, use the create local-user command.

create local-user name

Syntax Description

name	Local user name. The range of valid values is 1 to 74.

Command Default

None

Command Modes

Security (/security)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a local user, and enter organization local user mode.

Examples

This example shows how to create a local user:

switch# scope security
switch /security # scope local-user lu1
switch /security # create local-user lu2
switch /security/local-user* # commit-buffer                                          
switch /security/local-user #                                           

Related Commands

Command	Description
show locale
show local-user

create mac-pool

To create a MAC address pool, use the create mac-pool command.

create mac-pool name

Syntax Description

name	MAC address pool name. The name can be up to 32 alphanumeric characters.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a block of MAC addresses, and enter organization MAC pool mode.

Examples

This example shows how to create a MAC pool:

switch# scope org org3
switch /org # create mac-pool mp1
switch /org/mac-pool* # commit-buffer
switch /org/mac-pool # 

Related Commands

Command	Description
show block
show pooled

create mac-security

To create MAC security, use the create mac-security command.

create mac-security

This command has no arguments or keywords.

Command Default

None

Command Modes

Port profile (/eth-uplink/port-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create MAC security, and enter organization MAC security mode.

Examples

This example shows how to create MAC security:

switch# scope eth-uplink
switch /eth-uplink # scope port-profile pp1                                       
switch /eth-uplink/port-profile # create mac-security 
switch /eth-uplink/port-profile/mac-security* # commit-buffer
switch /eth-uplink/port-profile/mac-security #                                       

Related Commands

Command	Description
show mac-security
show port-profile

create member-port

To create a member port, use the create member-port command.

create member-port { a | b } slot-id port-id

Syntax Description

a	Specifies port A.
b	Specifies port B.
slot-id	Slot identification number. The range of valid values is 1 to 5.
port-id	Port identification number. The range of valid values is 1 to 40.

Command Default

None

Command Modes

Port channel (/eth-uplink/switch/port-channel)

VSAN under Fibre Channel uplink (/fc-uplink/vsan)

VSAN under fabric interconnect (/fc-uplink/fabric/vsan)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a member port, and enter organization member port mode.

Examples

This example shows how to create a member port:

switch# scope eth-uplink
switch /eth-uplink # scope switch b                                             
switch /eth-uplink/switch # scope port-channel 3  
switch /eth-uplink/switch/port-channel # create member-port 2 4
switch /eth-uplink/switch/port-channel/member-port* # commit-buffer  
switch /eth-uplink/switch/port-channel/member-port #                                         

Related Commands

Command	Description
show member-port
show port-channel

create memory

To create a memory qualifier, use the create memory command.

create memory

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a memory qualifier, and enter organization memory mode.

Examples

This example shows how to create a memory qualifier:

Pubs-A# scope org org3
Pubs-A /org # scope server-qual sq20                                       
Pubs-A /org/server-qual # create memory 
Pubs-A /org/server-qual/memory* # commit-buffer
Pubs-A /org/server-qual/memory #                                       

Related Commands

Command	Description
show memory
show processor

create ntp-server

To create an NTP server, use the create ntp-server command.

create ntp-server name

Syntax Description

name	Server name.

Command Default

None

Command Modes

Services (/system/services)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create an NTP server, and enter organization NTP server mode.

Examples

This example shows how to create an NTP server:

switch-A# scope system
switch-A /system # scope services                                          
switch-A /system/services # create ntp-server ntps1   
switch-A /system/services/ntp-server* # commit-buffer
switch-A /system/services/ntp-server #                                        

Related Commands

Command	Description
show dns
show ntp

create nwctrl-policy

To create a network control policy, use the create nwctrl-policy command.

create nwctrl-policy policy-name

Syntax Description

policy-name

Policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(2)	This command was introduced.

Usage Guidelines

When you create a network control policy, you can use the policy to perform the following tasks:

• Enable CDP

• Set up an uplink fail action

Examples

This example shows how to create a network control policy:

switch-A# scope org org10
switch-A /org # create nwctrl-policy netCtrlP10                                        
switch-A /org/nwctrl-policy* # commit-buffer
switch-A /org/nwctrl-policy #                                      

Related Commands

Command	Description
show nwctrl-policy
show service-policy

create org

To create an org, use the create org command.

create org name

Syntax Description

name	Org name. The range of valid values is 1 to 80.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Organizations are logical entities that you can use to divide up large physical infrastructures into smaller infrastructures.

Use this command to create an organization, and enter organization mode.

Examples

This example shows how to create an org:

Pubs-A# scope org org3
Pubs-A /org # create org org4                                          
Pubs-A /org* # commit-buffer  
Pubs-A /org #                                         

Related Commands

Command	Description
show mac-pool
show org

create org-ref

To create a organization reference, use the create org-ref command.

create org-ref name orgdn domain-name

Syntax Description

name	Organization name. The range of valid values is 1 to 16.
orgdn	Specifies the organization domain name.
domain-name	Domain name.

Command Default

None

Command Modes

Locale (/security/locale)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The create org-ref command creates a an organization reference to a locale. Use this command to create a organization reference, and enter organization organization reference mode.

You can specify more than one org-ref-name and orgdn-name argument on the same command line to reference multiple organizations to the locale, or you can add organizations to the same locale using multiple create org-ref commands.

Examples

This example shows how to create an organization reference to a locale:

switch# scope security
switch /security # scope locale locale1                                             
switch /security/locale # create org-ref or3 orgdn or30   
switch /security/locale/org-ref* # commit-buffer
switch /security/locale/org-ref #                                          

Related Commands

Command	Description
show locale
show org

create pack-image

To create an image pack, use the create pack-image command.

create pack-image hw-vendor hw-model { server-bios | adapter | raid-controller | host-nic | host-hba | host-hba-optionrom } version

Syntax Description

hw-vendor	Hardware vendor.
hw-model	Hardware model number.
server-bios	Specifies the image for the server.
adapter	Specifies the image for the adapter.
raid-controller	Specifies the image for the RAID array.
host-nic	Specifies the image for the host NIC.
host-hba	Specifies the image for the host HBA.
host-hba-optionrom	Specifies the image for the host HBA optional ROM.
version	Hardware version.

Command Default

None

Command Modes

Firmware management package (/org/fw-mgmt-pack)

Firmware host package (/org/fw-host-pack)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

A pack is a collection of host firwmare images.

Use this command to create a pack-image, and enter organization pack image mode.

Keywords found in the create pack-image command are not supported in /org/fw-mgmt-pack mode.

Examples

This example shows how to create an image pack:

switch# scope org org3
switch /org # scope fw-mgmt-pack fmp1                                                
switch /org/fw-mgmt-pack # create pack-image hp 1100 bmc 1.2  
switch /org/fw-mgmt-pack/pack-image* # commit-buffer  
switch /org/fw-mgmt-pack/pack-image #                                             

Related Commands

Command	Description
show fw-host-pack
show fw-mgmt-pack

create path

To create a LAN image path, use the create path command.

create path { primary | secondary }

Syntax Description

primary	Specifies a primary path.
secondary	Specifies specifies a secondary path.

Command Default

None

Command Modes

SAN image under boot-definition/storage (/org/service-profile/boot-def/storage/san-image)

LAN under boot-policy (/org/boot-policy/lan)

LAN under boot-definition /org/service-profile/boot-def/lan

SAN image under boot-policy/storage (/org/boot-policy/storage/san-image)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The LAN image path is the path the vNIC used when booting from an image on a LAN, such as a PXE boot. For each path you can specify the vNIC to use.

Use this command to create a LAN image path, and enter organization path mode.

Examples

This example shows how to create a LAN image path:

switch# scope org org3
switch /org # scope boot-policy boot1                                             
switch /org/boot-policy # scope lan
switch /org/boot-policy/lan # create path primary
switch /org/boot-policy/lan/path* # commit-buffer 
switch /org/boot-policy/lan/path #                                             

Related Commands

Command	Description
show lan
show path

create physical-qual

To create a physical qualifier for a server pool policy, use the create physical-qual command.

create physical-qual

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command create a physical qualifier for a server pool policy, and to enter organization physical qualifier mode.

Examples

This example shows how to create a physical qualifier:

switch# scope org org3
switch /org # scope server-qual sq20
switch /org/server-qual # create physical-qual
switch /org/server-qual/physical-qual* # commit-buffer
switch /org/server-qual/physical-qual #

Related Commands

Command	Description
show physical-qual
show server-qual

create pin-group

To create a pin group, use the create pin-group command.

create pin-group name

Syntax Description

name	Pin group name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Ethernet uplink (/eth-uplink)

Fibre Channel uplink (/fc-uplink)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Pinning in Cisco UCS is only relevant to uplink ports.

When you determine the optimal configuration for pin groups and pinning for an uplink port, consider the estimated bandwidth usage for the servers. If you know that some servers in the system will use a lot of bandwidth, ensure that you pin these servers to different uplink ports.

Use this command to create a pin group, and enter organization pin-group mode.

Examples

This example shows how to create a pin group:

switch# scope eth-uplink
switch /eth-uplink # create pin-group pg110
switch /eth-uplink/pin-group* # commit-buffer  
switch /eth-uplink/pin-group #                                   

Related Commands

Command	Description
show eth-uplink
show pin-group

create policy

To create a policy, use the create policy command.

callhome mode create policy event

flow-control mode create policy name

Syntax Description

event	Select a predefined fault or system event type. See Usage Guidelines for event options.
name	Policy name. The name can be from 1 to 16 characters.

Command Default

None

Command Modes

Callhome (/monitoring/callhome)

Flow control (/eth-uplink/flow-control)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.1(1)	This command was modified to add additional event types for Call Home.

Usage Guidelines

Use this command to create a policy, and enter either organization callhome or organization flow control mode.

In Call Home configuration, use this command to create an instance of a policy for a predefined type of fault or system event. The following list shows the available keywords for Call Home event types:

• association-failed
• chassis-seeprom-error
• configuration-failure
• connectivity-problem
• election-failure
• equipment-inaccessible
• equipment-inoperable
• equipment-problem
• fru-problem
• identity-unestablishable
• link-down
• management-services-failure
• management-services-unresponsive
• power-problem
• thermal-problem
• unspecified
• version-incompatible
• voltage-problem

In Flow Control configuration, use this command to create a named policy.

Examples

This example shows how to create and enable a Call Home policy instance for link-down events:

switch-A# scope monitoring
switch-A /monitoring # scope callhome
switch-A /monitoring/callhome # create policy link-down
switch-A /monitoring/callhome/policy # set admin-state enabled
switch-A /monitoring/callhome/policy* # commit-buffer
switch-A /monitoring/callhome/policy # 

This example shows how to create a named policy for flow control:

switch-A # scope eth-uplink
switch-A /eth-uplink # scope flow-control
switch-A /eth-uplink/flow-control # create policy policy1
switch-A /eth-uplink/flow-control* # commit-buffer
switch-A /eth-uplink/flow-control # 

Related Commands

Command	Description
enter policy
show policy
show stats-threshold-policy

create pooling-policy

To create a pooling policy, use the create pooling-policy command.

create pooling-policy name

Syntax Description

name	Policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Creates a server pooling policy, and enters organization pooling policy mode.

Examples

This example shows how to create a pooling policy:

switch# scope org org3
switch /org # create pooling-policy pp110                                      
switch /org/pooling-policy* # commit-buffer  
switch /org/pooling-policy #                                   

Related Commands

Command	Description
show policy
show pooling-policy

create port-channel

To create a port channel, use the create port-channel command.

create port-channel id

Syntax Description

id	Port identification number. The range of valid values is 1 to 40.

Command Default

None

Command Modes

Fabric interconnect (/eth-uplink/fabric)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Consider using a port channel to make best use of capacity when multiple uplinks are used on a switch.

Use this command to create a port channel, and enter organization port channel mode.

Examples

This example shows how to create a port channel:

switch# scope eth-uplink
switch /eth-uplink # scope switch b                                       
switch /eth-uplink/switch # create port-channel 20
switch /eth-uplink/switch/port-channel* # commit-buffer  
switch /eth-uplink/switch/port-channel #                                   

Related Commands

Command	Description
show port-channel
show switch

create port-profile (eth-uplink)

To create a port profile, use the create port-profile command.

create port-profile name

Syntax Description

name	Port profile name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Ethernet uplink (/eth-uplink)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a port profile, and enter organization port profile mode.

Examples

This example shows how to create a port profile:

switch# scope eth-uplink
switch /eth-uplink # create port-profile pp110                                       
switch /eth-uplink/port-profile* # commit-buffer 
switch /eth-uplink/port-profile # 

Related Commands

Command	Description
show eth-uplink
show port-profile

create port-profile (profile-set)

To create a port profile, use the create port-profile command in profile-set mode.

create port-profile profile-name

Syntax Description

profile-name

The name of the profile. A unique set of numbers or letters that identifies the profile. The range of valid values is 1 to 31.

Command Default

None

Command Modes

Profile set (/system/vm-mgmt/vmware/profile-set)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

The port profile client determines the DVSes to which a port profile is applied. By default, a port profile applies to all DVSes in the vCenter; however, you can use a port profile client to apply a port profile to all DVSes in a specific datacenter or datacenter folder, or to a specific DVS.

create port-profile creates the specified port profile and enters system VM management VMware profile set port profile mode.

Examples

This example shows how to create a port profile:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # create port-profile pp100
switch-A /system/vm-mgmt/vmware* # commit-buffer
switch-A /system/vm-mgmt/vmware #                                      

Related Commands

Command	Description
show
show port profile

create processor

To create a processor qualifier for a server pool policy, use the create processor command.

create processor

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.3(1)	This command was removed.

Usage Guidelines

Use this command create a processor qualifier for a server pool policy, and to enter organization processor mode.

Only one processor qualifier can be created.

Note	In later releases, this command is replaced by the create cpu command.

Examples

This example shows how to create a processor qualifier:

switch# scope org org3
switch /org # scope server-qual sq20
switch /org/server-qual # create processor 
switch /org/server-qual/processor* # commit-buffer  
switch /org/server-qual/processor #

Related Commands

Command	Description
show processor
show server-qual

create profile

To create a profile, use the create profile command.

create profile name

Syntax Description

name	Profile name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Callhome (/monitoring/callhome)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a profile, and enter organization profile mode.

Examples

This example shows how to create a profile:

switch# scope monitoring
switch /monitoring # scope callhome                                       
switch /monitoring/callhome # create profile p210
switch /monitoring/callhome/profile* # commit-buffer  
switch /monitoring/callhome/profile #                                   

Related Commands

Command	Description
show callhome
show profile

create qos-policy

To create a QoS policy, use the create qos-policy command in org mode.

create qos-policy policy-name

Syntax Description

policy-name

The name of the QoS policy. A unique set of numbers or letters that identifies the policy. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to create a QoS policy:

switch-A# scope org                                       
switch-A /org # create qos-policy qp10
switch-A /org* # commit-buffer
switch-A /org #                                      

Related Commands

Command	Description
show egress-policy
show qos-policy

create role

To create a role, use the create role command.

create role name

Syntax Description

name	Role name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Local user (/security/local-user)

Security (/security)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a role, and enter organization role mode.

Examples

This example shows how to create a role:

switch# scope security
switch /security # create role admin                                       
switch /security/role* # commit-buffer 
switch /security/role #                                   

Related Commands

Command	Description
show local-user
show role

create san-image

To create a SAN image, use the create san-image command.

create san-image { primary | secondary }

Syntax Description

primary	Specifies primary image.
secondary	Specifies secondary image.

Command Default

None

Command Modes

Storage (/org/service-profile/boot-def/storage)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Only one SAN image can be created and committed.

Use this command to create a SAN image, and enter organization SAN image mode.

Examples

This example shows how to create a SAN image:

switch#scope org org3
switch /org # scope service-profile sp1
switch /org/service-profile # scope boot-def
switch /org/service-profile/boot-def # scope storage
switch /org/service-profile/boot-def/storage # create san-image primary                                             
switch /org/service-profile/boot-def/storage/san-image* # commit-buffer 
switch /org/service-profile/boot-def/storage/san-image #                                             

Related Commands

Command	Description
show local
show san-image

create scrub-policy

To create a scrub policy, use the create scrub-policy command.

create scrub-policy name

Syntax Description

name	Scrub policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a scrub policy, and enter organization scrub policy mode.

Examples

This example shows how to create a scrub policy:

switch# scope org org100
switch /org # create scrub-policy scrub100 
switch /org/scrub-policy* # commit-buffer                                         
switch /org/scrub-policy #                                           

Related Commands

Command	Description
show server-disc-policy
show scrub-policy

create server

To create a server, use the create server command.

create server { server-name | | chassis-id/slot-id }

Syntax Description

server-name	The name of the server. Valid entries for this value are a name or an IP address. The range of valid values for a name is 1 to 16.
chassis-id/slot-id	Chassis and slot identification numbers.

Command Default

None

Command Modes

VMware management (/system/vm-mgmt)

LDAP (/security/ldap)

TACACS (/security/tacacs)

RADIUS (/security/radius)

Server pool (/org/server-pool)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

This command takes the name argument only in the /org/server-pool mode.

Use this command to create a server, and enter organization server mode.

Examples

This example shows how to create a server:

switch#scope security
switch /security # scope radius                                          
switch /security/radius # create server radius 209.165.200.226 
switch /security/radius/server* # commit-buffer
switch /security/radius/server #                                          

Related Commands

Command	Description
show aaa
show server

create server-autoconfig-policy

To create a server automatice configuration policy, use the create server-autoconfig-policy command.

create server-autoconfig-policy name

Syntax Description

name	Policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The server-autoconfig-policy command is definable only in org /.

Use this command to create a server automatic configuration policy with the specified policy name, and enters organization server automatic configuration policy mode.

Examples

This example shows how to create a server autoconfiguration policy:

switch#scope org org3
switch /org # create server-autoconfig-policy sap110                                          
switch /org/server-autoconfig-policy* # commit-buffer
switch /org/server-autoconfig-policy #                                           

Related Commands

Command	Description
show server-disc-policy
show server-autoconfig-policy

create server-disc-policy

To create a server discovery policy, use the create server-disc-policy command.

create server-disc-policy name

Syntax Description

name	Server discovery policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The server-disc-policy command is definable only in org /.

Use this command to create a server discovery policy, and enter organization server discovery policy mode.

Examples

This example shows how to create a server discovery policy:

switch#scope org org3
switch /org # create server-disc-policy sdp110                                          
switch /org/server-disc-policy* # commit-buffer
switch /org/server-disc-policy #                                           

Related Commands

Command	Description
show server-disc-policy
show server-autoconfig-policy

create server-inherit-policy

To create a server inherit policy, use the create server-inherit-policy command.

create server-inherit-policy name

Syntax Description

name	Policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

The server-inherit-policy command is definable only in org /.

Use this command to create a server inherit policy, and enter organization server inherit policy mode.

Examples

This example shows how to create a server inherit policy:

switch#scope org /
switch /org # create server-inherit-policy sip110                                          
switch /org/server-inherit-policy* # commit-buffer
switch /org/server-inherit-policy #                                           

Related Commands

Command	Description
show server-disc-policy
show server-inherit-policy

create server-pool

To create a server pool, use the create server-pool command.

create server-pool name

Syntax Description

name	Server pool name. The name can be up to 32 alphanumeric characters.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a server pool, and enter organization server pool mode.

Examples

This example shows how to create a server pool:

switch#scope org org3
switch /org # create server-pool sPool10
switch /org/server-pool* # commit-buffer
switch /org/server-pool #

Related Commands

Command	Description
show org
show server-pool

create server-qual

To create a server qualifier, use the create server-qual command.

create server-qual name

Syntax Description

name	Server qualifier name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a server qualifier, and enter organization server qualification mode.

Examples

This example shows how to create a server qualifier:

switch#scope org org3
switch /org # create server-qual sql10                                          
switch /org/server-qual* # commit-buffer 
switch /org/server-qual #                                          

Related Commands

Command	Description
show server-pool
show server-qual

create service-profile

To create a service profile, use the create service-profile command.

create service-profile name [ initial-template | | instance | | updating-template ]

Syntax Description

name	The service profile name. The range of valid values is 1 to 16.
initial-template	Specifies that instances will not automatically update if this template is updated.
instance	Specifies the service profile instance.
updating-template	Specifies that instances will automatically update if this template is updated.

Command Default

None.

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a service profile, and enter service profile mode.

Examples

The following example shows how to create a service profile.

switch# scope org org110
switch /org # create service-profile spEast110                                                   
switch /org/service-profile* # commit-buffer
switch /org/service-profile #                                                    

Related Commands

Command	Description
show ipmi-access-profile
show service-profile

create slot

To create a slot, use the create slot command.

create slot min-id max-id

Syntax Description

min-id	Minimum slot identification number. The range of valid values is 1 to 8.
max-id	Maximum slot identification number. The range of valid values is 1 to 8.

Command Default

None

Command Modes

Chassis (/org/server-qual/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a slot with the specified ID, and enters organization slot mode.

Examples

This example shows how to create a slot:

switch# scope org org10
switch /org # scope server-qual sq10                                             
switch /org/server-qual # scope chassis 1 1
switch /org/server-qual/chassis # create slot 1 1
switch /org/server-qual/chassis/slot* # commit-buffer
switch /org/server-qual/chassis/slot #                                              

Related Commands

Command	Description
show chassis
show slot

create snmp-trap

To create an SNMP trap, use the create snmp-trap command.

create snmp-trap ip-address

Syntax Description

ip-address

Host IP address. Specify the IP address in the format A.B.C.D.

Command Default

None

Command Modes

Monitoring (/monitoring)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You must create an SNMP community before you create an SNMP trap.

Examples

This example shows how to create an SNMP trap:

switch#scope monitoring
switch /monitoring # create snmp-trap 192.0.2.34                                          
switch /monitoring/snmp-trap* # commit-buffer
switch /monitoring/snmp-trap #                                           

Related Commands

Command	Description
show snmp
show snmp-trap

create snmp-user

To create an SNMPv3 user, use the create snmp-user command.

create snmp-useruser-name

Syntax Description

user-name

User name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(2)	This command was introduced.

Examples

This example shows how to create an SNMPv3 user:

switch-A# scope monitoring                                        
switch-A /monitoring # create snmp-user snmpUser10
switch-A /monitoring* # commit-buffer
switch-A /monitoring #                                       

Related Commands

Command	Description
show snmp
show snmp-user

create sol-config

To create a Serial over LAN (SoL) configuration, use the create sol-config command.

create sol-config

This command has no arguments or keywords.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a SoL configuration, and enter organization SoL configuration mode.

Examples

This example shows how to create a SoL configuration:

switch-A# scope org org30
switch-A /org # scope service-profile sp30a                                       
switch-A /org/service-profile # create sol-config
switch-A /org/service-profile/sol-config* # commit-buffer 
switch-A /org/service-profile/sol-config #                                       

Related Commands

Command	Description
show sol-config
show sol-policy

create sol-policy

To create an SoL policy, use the create sol-policy command.

create sol-policy name

Syntax Description

name	SoL policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a SoL policy with the specified name, and enters organization SoL policy mode.

Examples

This example shows how to create a SoL policy:

switch-A# scope org org3
switch-A /org # create sol-policy solpol1                                                
switch-A /org/sol-policy* # commit-buffer  
switch-A /org/sol-policy #                           

Related Commands

Command	Description
show org
show sol-policy

create stats-threshold-policy

To create a statistics threshold policy, use the create stats-threshold-policy command.

create stats-threshold-policy name

Syntax Description

name	Policy name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a statistics threshold policy, and enter organization statistics threshold policy mode.

Examples

This example shows how to create a statistics threshold policy:

switch# scope org org10
switch /org # create stats-threshold-policy stp10                                                
switch /org/stats-threshold-policy* # commit-buffer 
switch /org/stats-threshold-policy #                                                

Related Commands

Command	Description
show pooling-policy
show stats-threshold-policy

create storage

To create storage, use the create storage command.

create storage

This command has no arguments or keywords.

Command Default

None

Command Modes

Boot definition (/org/service-profile/boot-def)

Boot policy (/org/boot-policy)

Server qualification (/org/server-qual)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a storage qualification, and enter organization server qualification storage mode.

Examples

This example shows how to create storage:

switch-A# scope org org3
switch-A /org # scope service-profile sp1                                                
switch-A /org/service-profile # scope boot-def bd1  
switch-A /org/service-profile/boot-def # create storage 
switch-A /org/service-profile/boot-def/storage* # commit-buffer 
switch /org/service-profile/boot-def/storage #                                             

Related Commands

Command	Description
show boot-definition
show storage

create threshold-value

To create a threshold value for a property, use the create threshold-value command.

create threshold-value { above-normal | | below-normal } { cleared | | condition | | critical | | info | | major | | minor | | warning }

Syntax Description

above-normal	Sets the value to above normal.
below-normal	Sets the value to below normal.
cleared	Sets the threshold value to cleared.
condition	Sets the threshold value to condition.
critical	Sets the threshold value to critical.
info	Sets the threshold value to info.
major	Sets the threshold value to major.
minor	Sets the threshold value to minor.
warning	Sets the threshold value to warning.

Command Default

None

Command Modes

Ethernet uplink (/eth-uplink/stats-threshold-policy/class/property)

Fibre channel (/fc-uplink/stats-threshold-policy/class/property)

Ethernet server (/eth-server/stats-threshold-policy/class/property)

Organization (/org/stats-threshold-policy/class/property)

Command History

Release	Modification
1.0.1	This command was introduced.

Usage Guidelines

This command creates the specified threshold value for the class property and enters organization statistics threshold policy class property threshold value mode. You must have a class and a property created in order to execute the set threshold-value command. The command is used to set the value of the property you created.

You can configure multiple threshold values for a class property. Before you use this command, use the set normal-value command to set a baseline.

Examples

The following example shows how to set the threshold value for the bytes-rx-delta property in vnic-stats class:

switch-A#scope org org100
switch-A /org # scope stats-threshold-policy stp100                                          
switch-A /org/stats-threshold-policy # scope class vnic-stats
switch-A /org/stats-threshold-policy/class # scope property bytes-rx-delta
switch-A /org/stats-threshold-policy/class/property # create threshold-value above-normal critical
switch-A /org/stats-threshold-policy/class/property* # commit-buffer
switch-A /org/stats-threshold-policy/class/property #                                           

Related Commands

Command	Description
show property
show threshold-value

create trustpoint

To create a trustpoint, use the create trustpoint command.

create trustpoint name

Syntax Description

name	Trustpoint name. The name can be up to 16 alphanumeric characters.

Command Default

None

Command Modes

Security (/security)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to identify the trustpoints that will be used to validate a certificate during Internet Key Exchange (IKE) authentication, and enter organization trustpoint mode.

Examples

This example shows how to create a trustpoint:

switch-A# scope security
switch-A /security # create trustpoint tPoint10
switch-A /security/trustpoint* # commit-buffer
switch-A /security/trustpoint # 

Related Commands

Command	Description
show keyring
show trustpoint

create uuid-suffix-pool

To create a UUID suffix pool, use the create uuid-suffix-pool command.

create uuid-suffix-pool name

Syntax Description

name	UUID suffix pool name. The name can be up to 32 alphanumeric characters.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Creates a UUID suffix pool with the specified name, and enters organization UUID suffix pool mode.

Examples

This example shows how to create a UUID suffix pool:

switch-A# scope org org3                                       
switch-A /org # create uuid-suffix-pool uuidsp1 
switch-A /org/uuid-suffix-pool* # commit-buffer
switch-A /org/uuid-suffix-pool #                                       

Related Commands

Command	Description
show uuid-suffix-pool
show wwn-pool

create vcenter

To create a VCenter, use the create vcenter command in vmware mode.

create vcenter vcenter-name

Syntax Description

vcenter-name

The name of the VCenter. A unique set of numbers or letters that identifies the VCenter. The range of valid values is 1 to 16.

Command Default

None

Command Modes

VMware (/system/vm-mgmt/vmware)

Command History

Release	Modification
1.1(1)	This command was introduced.

Examples

This example shows how to create a VCenter:

switch-A# scope system                                       
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # create vcenter vc10
switch-A /system/vm-mgmt/vmware* # commit-buffer
switch-A /system/vm-mgmt/vmware #                                      

Related Commands

Command	Description
show vcenter
show virtual-machine

create vcon

To create a vCon (virtual network interface connection), use the create vcon command.

create vcon { 1 | | 2 }

Syntax Description

1	Specifies virtual network interface connection 1.
2	Specifies virtual network interface connection 2.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.1(1)	This command was introduced.

Examples

This example shows how to create a vCon:

switch-A# scope org org100                                       
switch-A /org # scope service-profile sp100
switch-A /org/service-profile # create vcon vc100
switch-A /org/service-profile* # commit-buffer
switch-A /org/service-profile #                                      

Related Commands

Command	Description
show service-profile
show vcon

create vcon-policy

To create a vCon policy (vNIC/vHBA placement profile), use the create vcon-policy command.

create vcon-policy policy-name

Syntax Description

policy-name

The name of the policy.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Creates the specified vCon policy and enters organization vcon-policy mode. vCon policies determine the placement and distribution of vNICs and vHBAs between the adapters for a server that has more than one adapter.

policy-name should be a unique set of numbers or letters that identifies the policy. The range of valid values is 1 to 16.

Examples

This example shows how to create a vCon policy:

switch-A# scope org /                                       
switch-A /org # create vcon-policy vcp100
switch-A /org* # commit-buffer
switch-A /org #                                      

Related Commands

Command	Description
show vcon
show vcon-policy

create vhba

To create a virtual HBA vHBA), use the create vhba command.

create vhba name { fabric { a | b } | fc-if fc-if } *

Syntax Description

name	vHBA name. The range of valid values is 1 to 16.
fabric	Specifies a fabric.
a	Specifies fabric A.
b	Specifies fabric B.
fc-if	Specifies a Fibre Channel interface.
interface-name	Interface name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a vHBA, and enter organization virtual HBA mode.

Examples

This example shows how to create a vHBA:

switch-A# scope org org30
switch-A /org # scope service-profile sp10a                                       
switch-A /org/service-profile # create vhba 10a 
switch-A /org/service-profile/vhba* # commit-buffer  
switch-A /org/service-profile/vhba #                                   

Related Commands

Command	Description
show vhba
show vnic

create vhba-templ

To create a vHBA template, use the create vhba-templ command.

create vhba-templ name { fabric { a | b } | fc-if fci-name } *

Syntax Description

name	vHBA template name. The range of valid values is 1 to 16.
fabric	Specifies fabric.
a	Specifies fabric A.
b	Specifies fabric B.
fc-if	Specifies a Fibre Channel interface.
fci-name	Fibre Channel interface name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

A vHBA is a virtualized host bus adapter that is configured on a physical network adapter and appears to be a physical HBA to the operating system of the server. The type of adapter in the system determines how many vHBAs you can create.

Use this command to create a vHBA template, and enter organization virtual HBA template mode.

Examples

This example shows how to create a vHBA template:

switch-A# scope org org10
switch-A /org # create vhba-templ vhbat10                                       
switch-A /org/vhba-templ* # commit-buffer 
switch-A /org/vhba-templ #   
                                 

Related Commands

Command	Description
show fc-if
show vhba-templ

create virtual-media

To create virtual media, use the create virtual-media command.

create virtual-media { read-only | read-write }

Syntax Description

read-only	Specifies read-only virtual media.
read-write	Specifies read and write virtual media.

Command Default

None

Command Modes

Boot policy (/org/boot-policy)

Boot definition (/org/service-profile/boot-def)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create virtual media with the specified name, and enters organization virtual-media mode.

Examples

This example shows how to create virtual media:

switch-A# scope org org3
switch-A /org # scope service-profile sp1                                       
switch-A /org/service-profile # scope boot-def 
switch-A /org/service-profile/boot-definition # create virtual-media read-write
switch-A /org/service-profile/boot-definition/virtual-media* # commit-buffer  
switch-A /org/service-profile/boot-definition/virtual-media #                                   

Related Commands

Command	Description
show storage
show virtual-media

create vlan

To create a VLAN, use the create vlan command.

create vlan name id

Syntax Description

name	VLAN name. The name can contain up to 16 characters.
id	VLAN identification number. The range of valid values is 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Ethernet uplink (/eth-uplink)

Fabric (/eth-uplink/fabric)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a VLAN with the specified name and identifier number and enter vlan mode.

Examples

This example shows how to create a VLAN:

switch-A# scope eth-uplink
switch-A /eth-uplink # create vlan vlan1 10
switch-A /eth-uplink/vlan* # commit-buffer 
switch-A /eth-uplink/vlan # 

Related Commands

Command	Description
show interface
show vlan

create vlan (port-profile)

To create a VLAN for a port profile, use the create vlan command.

create vlan name

Syntax Description

name	VLAN name. The name can contain up to 16 characters.

Command Default

None

Command Modes

Port profile (/system/vm-mgmt/vmware/profile-set/port-profile)

Command History

Release	Modification
1.1(1)	This command was introduced.

Usage Guidelines

Use this command to create a VLAN with the specified name for a port profile and enter vlan mode.

Examples

This example shows how to create a VLAN for a port profile:

switch-A# scope system 
switch-A /system # scope vm-mgmt
switch-A /system/vm-mgmt # scope vmware
switch-A /system/vm-mgmt/vmware # scope profile-set
switch-A /system/vm-mgmt/vmware/profile-set # scope port-profile pp100
switch-A /system/vm-mgmt/vmware/profile-set/port-profile # create vlan v100
switch-A /system/vm-mgmt/vmware/profile-set/port-profile/vlan* # commit-buffer
switch-A /system/vm-mgmt/vmware/profile-set/port-profile/vlan #

Related Commands

Command	Description
show port-profile

create vnic

To create a VNIC (Virtual Network Interface Card), use the create vnic command.

create vnic name { fabric { a | a-b | b | b-a } | eth-if eth-if } *

Syntax Description

name	VNIC template name. The range of valid values is 1 to 16.
fabric	Specifies the fabric switch identification number.
a	Specifies switch A.
a-b	Specifies redundant, with switch A as primary.
b	Specifies switch B.
b-a	Specifies redundant, with switch B as primary.
eth-if	Specifies a Ethernet interface.
eth-if	Ethernet interface name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a vNIC with the specified name, and enters organization virtual NIC mode.

Examples

This example shows how to create a vNIC:

switch-A# scope org org3
switch-A /org # scope service-profile sp1                                       
switch-A /org/service-profile # create vnic vnic110 
switch-A /org/service-profile/vnic* # commit-buffer
switch-A /org/service-profile/vnic #                                       

Related Commands

Command	Description
show interface
show vnic

create vnic-egress-policy

To create a VNIC egress policy, use the create vnic-egress-policy command.

create vnic-egress-policy

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual NIC QoS (/org/vnic-qos)

Command History

Release	Modification
1.0(1)	This command was introduced.

Use this command to create a vNIC egress policy, and enter organization virtual NIC egress policy mode.

Examples

This example shows how to create a vNIC egress policy:

switch-A# scope org org3
switch-A /org # scope vnic-qos vnicq1                                       
switch-A /org/vnic-qos # create vnic-egress-policy 
switch-A /org/vnic-qos* # commit-buffer
switch-A /org/vnic-qos #                                       

Related Commands

Command	Description
show vnic
show vnic-egress-policy

create vnic-templ

To create a VNIC template, use the create vnic-templ command.

create vnic-templ name { fabric { a | a-b | b | b-a } | target { adapter | vm } + | eth-if eth-if } *

Syntax Description

name	vNIC template name. The range of valid values is 1 to 16.
fabric	Specifies the fabric switch identification number.
a	Specifies switch A.
a-b	Specifies redundant, with switch A as primary.
b	Specifies switch B.
b-a	Specifies redundant, with switch B as primary.
target	Specifies the target, either adapter or vm.
adapter	Specifies the adapter.
vm	Specifies the virtual machine.
eth-if	Specifies a Ethernet interface.
eth-if	Ethernet interface name. The range of valid values is 1 to 16.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a vNIC template, and enters organization virtual NIC template mode.

Examples

This example shows how to create a vNIC template:

switch-A# scope org org3
switch-A /org # create vnic-templ vnict1 eth-if 10                                       
switch-A /org/vnic-templ* # commit-buffer 
switch-A /org/vnic-templ #                                       

Related Commands

Command	Description
show eth-if
show vnic-templ

create vsan

To create a VSAN, use the create vsan command.

create vsan name id fcoe-vlan

Syntax Description

name	VSAN name. The range of valid values is 1 to 16.
id	VSAN identification number. The range of valid values is 1 to 4093.
default-2	Specifies default 1.
fcoe-vlan	Fibre Channel over Ethernet VLAN. The range of valid values is 1 to 4093.
default-1	Specifies default 2.

Command Default

None

Command Modes

Fibre Channel uplink (/fc-uplink)

Switch (/fc-uplink/switch)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a VSAN with the specified name, and enters organization VSAN mode.

You can create a named VSAN with IDs from 1 to 4093. VSANs configured on different FCoE VLANs cannot share the same ID.

Examples

This example shows how to create a VSAN:

switch-A# scope fc-uplink
switch-A /fc-uplink # create vsan vs2 6 10                                       
switch-A /fc-uplink/vsan* # commit-buffer 
switch-A /fc-uplink/vsan #                                       

Related Commands

Command	Description
show vif
show vsan

create wwn-pool

To create a WWN (World Wide Name) pool, use the create wwn-pool command.

create wwn-pool name { node-wwn-assignment | port-wwn-assignment }

Syntax Description

name	WWN pool name. The name can be up to 32 alphanumeric characters.
node-wwn-assignment	Specifies world wide node name assignment.
port-wwn-assignment	Specifies world wide node port assignment.

Command Default

None

Command Modes

Organization (/org)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to create a WWN pool with the specified name, and enters organization WWN pool mode.

A WWN pool can include only WWNNs or WWPNs in the 20:xx range. All other WWN ranges are reserved.

Examples

This example shows how to create a WWN pool:

switch-A# scope org org3                                       
switch-A /org # create wwn-pool wwnp1 port-wwn-assignment 
switch-A /org/wwn-pool* # commit-buffer
switch-A /org/wwn-pool #                                       

Related Commands

Command	Description
show mac-pool
show wwn-pool

cycle

To cycle a server, use the cycle command.

cycle { cycle-immediate | cycle-wait }

Syntax Description

cycle-immediate	Specifies cycle immediately.
cycle-wait	Specifies wait to cycle.

Command Default

None

Command Modes

Server (/chassis/server)

Service profile (/org/service-profile)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to cycle a server:

switch-A# scope server 2/4
switch-A /chassis/server # cycle cycle-immediate                                            
switch-A /chassis/server* # commit-buffer 
switch-A /chassis/server #                                             

decommission chassis

To decommission a chassis, use the decommission chassis command.

decommission chassis id

Syntax Description

id	Chassis identification number.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to decommission a chassis:

switch-A# decommission chassis 2
switch-A* # commit-buffer                                          
switch-A #                                           

Related Commands

Command	Description
show chassis
show server

decommission server

To decommission a server, use the decommission server command.

decommission server chassis-id/blade-id

Syntax Description

chassis-id/blade-id

Server chassis and blade identification number.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to decommission a server:

switch-A# decommission server 1 1
switch-A* # commit-buffer                                          
switch-A #                                           

Related Commands

Command	Description
show chassis
show server

delete adapter

To delete the adapter, use the delete adapter command.

delete adapter

This command has no arguments or keywords.

Command Default

None

Command Modes

Server qualification (/org/server-qual)

Command History

Release	Modification