Contents

• Cisco IOS Software Command Reference
• Password Reset Command
• Session Command
• IP Address Configuration Commands
• CIMC Access Commands
• VLAN Command
• Reload, Reset, Start, Stop, Shutdown Commands
• Statistics and Status Commands
• Boot Commands

Cisco IOS Software Command Reference

---

This chapter lists the Cisco IOS commands used to configure the host router and the E-Series Server.

For details about each command, such as command history, usage guidelines, and examples, see the Cisco IOS Interface and Hardware Component Command Reference at http://www.cisco.com/en/US/docs/ios-xml/ios/interface/command/ir-cr-book.html.

This chapter includes the following sections:

• Password Reset Command
• Session Command
• IP Address Configuration Commands
• CIMC Access Commands
• VLAN Command
• Reload, Reset, Start, Stop, Shutdown Commands
• Statistics and Status Commands
• Boot Commands

Password Reset Command

Commands	Description
ucse slot password-reset {BIOS | BMC}	Resets the BIOS, CIMC, or RAID password. slot—Router slot number in which the E-Series Server is installed. BIOS—Resets the BIOS password. BMC—Resets the CIMC password.

Session Command

Commands

Description

ucse slot session {imc [clear] | host [clear]}

Starts or closes a session with the host E-Series Server or with CIMC. slot—Router slot number in which the E-Series Server is installed. imc—Starts a session with CIMC. imc clear—Clears the existing CIMC session. host—Starts a session with the host E-Series Server. host clear—Clears the host E-Series Server session. Note    If serial-over-LAN is enabled in CIMC, the session host command will not display any output.

IP Address Configuration Commands

Commands	Description
imc ip address ip_address subnet_mask default-gateway gateway_address no imc ip address ip_address subnet_mask default-gateway gateway_address	Configures a static IP address for CIMC and the IP address of the default gateway router that CIMC must use. ip_address —IP address of CIMC. subnet_mask—Subnet mask to append to the IP address; must be in the same subnet as the host router. gateway_address—IP address of the default gateway router.
imc ip address dhcp no imc ip address dhcp	Configures a dynamic IP address for CIMC.

CIMC Access Commands

Commands	Description
imc access-port {dedicated | shared-lom [GE1 | GE2 | GE3 | console | failover [option]} no imc access-port {dedicated | shared-lom [GE1 | GE2 | GE3 | console | failover [option]}	Configures CIMC access through the E-Series Server’s dedicated or shared LOM ports. dedicated—Configures CIMC access using the Management (dedicated) port. shared-lom—Configures CIMC access using one of the following shared LOM ports: GE1 GE2 GE1 console failover option—If you enter failover, you must also enter one of the additional parameters: GE1 GE1 [GE2] | [GE3] [GE2 GE3] GE2 GE2 GE3

VLAN Command

Commands	Description
imc vlan vlan_number no imc vlan	Enters VLAN configuration mode for the specified VLAN.

Reload, Reset, Start, Stop, Shutdown Commands

Commands	Description
ucse slot reload	Gracefully shuts down the E-Series Server and then powers it on. slot—Router slot number in which the E-Series Server is installed.
ucse slot reset	Resets the hardware on the E-Series Server. slot—Router slot number in which the E-Series Server is installed.
ucse slot start	Powers on the E-Series Server. slot—Router slot number in which the E-Series Server is installed.
ucse slot stop	Powers down the E-Series Server immediately. slot—Router slot number in which the E-Series Server is installed.
ucse slot shutdown	Gracefully shuts down the E-Series Server. slot—Router slot number in which the E-Series Server is installed.

Statistics and Status Commands

Commands	Description
ucse slot statistics [clear]	Displays or clears the reset and reload information of the E-Series Server. slot—Router slot number in which the E-Series Server is installed. clear—Clears the E-Series Server's reset and reload information.
ucse slot status [detailed]	Displays configuration information related to the hardware and software on the E-Series Server. slot—Router slot number in which the E-Series Server is installed. detailed—Displays detail information about the E-Series Server, such as the status of the server and settings of the reset and heartbeat-reset flags.

Boot Commands

Commands	Description
ucse slot cmos-reset	Resets the BIOS CMOS of the E-Series Server. slot—Router slot number in which the E-Series Server is installed.