Getting Started Guide for Cisco UCS E-Series Servers, Release 1.0 - Diagnostic Tests [Cisco UCS E-Series Servers]

Contents
Diagnostic Tests
Diagnostic Tests Overview
Mapping the Diagnostics Image to the Host
Running Diagnostic Tests
Diagnostic Tests

This chapter includes the following sections:

Diagnostic Tests Overview
Mapping the Diagnostics Image to the Host
Running Diagnostic Tests

Diagnostic Tests Overview

Diagnostics is a standalone utility that runs on the E-Series Server independent of the operating system or applications running on the server. If you experience problems with the E-Series Server, you can use diagnostics tests to run a preliminary check and isolate the problem. Diagnostic tests can be executed on the server CPU, memory, and block devices. Block devices include hard drive, USB drive, and SD cards.

If the diagnostic tests pass successfully, it indicates that there is no problem with the server CPU, memory, or block devices. The problem could be with some other hardware component or with the software configuration. Open a service request with Cisco Technical Assistance Center (TAC) at: http://www.cisco.com/cisco/web/support/index.html to isolate the problem.

If the diagnostic tests fail, open a service request with Cisco TAC for further assistance.

Caution
Diagnostic tests are non-destructive, but if there is a power or equipment failure when the tests are running, there is a possibility that the disk data might get corrupted. We highly recommend that you backup the data before running these tests.

Basic Workflow for Executing Diagnostic Tests
Backup data.

The diagnostics image is pre-installed on the E-Series Server at the time of purchase. You can also choose to download the most current diagnostics image from a specified FTP, FTPS, HTTP, or HTTPS server onto the CIMC internal repository.

Mount the diagnostics image onto the HDD virtual drive of a USB controller.

Set the boot order to make EFI Shell as the first boot device.

Reboot the server.

Run diagnostic tests from the EFI Shell.

Reset the virtual media boot order to its original setting.

Mapping the Diagnostics Image to the Host

Before You Begin
Backup data.

Log into CIMC as a user with admin privileges.

The diagnostics image is pre-installed on the E-Series Server at the time of purchase. You can also choose to download the most current diagnostics image from a specified FTP, FTPS, HTTP, or HTTPS server onto the CIMC internal repository. See Obtaining Software from Cisco Systems.

Note
If you start an image update while an update is already in process, both updates will fail.

Procedure
Step 1   In the Navigation pane, click the Server tab.

Step 2   On the Server tab, click Host Image Mapping.
Figure 1. Host Image Mapping

Step 3   In the Install Pane, complete the following fields:
Name Description

URL field

The URL of the remote server on which the diagnostics image is located.

If the remote server requires user authentication, you must add the username and password of the remote server in the URL. The remote server can be an FTP, FTPS, HTTP, or HTTPS server.

The URL syntax must be: protocol://username:password@server-ip-address/path/filename

Image Name field

The name of the diagnostics image.

The image name must have .diag as the file extension.

Step 4   Click Download.
The diagnostics file is downloaded from the specified FTP, FTPS, HTTP, or HTTPS server onto the CIMC internal repository.

Step 5   Click Map Diagnostics to Host.
The diagnostics image is mounted on the HDD virtual drive of the USB controller.

Step 6   Set the boot order to make EFI Shell as the first boot device.
To set the boot order, see Configuring the Server Boot Order.

Step 7   Reboot the server.
The EFI Shell appears.

What to Do Next

Run diagnostic tests.
Running Diagnostic Tests
From the EFI Shell, use the following procedure to run diagnostic tests.

Before You Begin
Backup data. All tests are non-destructive, but if there is power or equipment failure when the tests are running, there is a possibility that the disk data might get corrupted. We highly recommend that you backup data before executing these tests.

Use the CIMC CLI or the CIMC GUI to download and map the diagnostics image onto the HDD virtual drive of the USB controller.

Reboot the server. The EFI Shell displays.

Procedure
Command or Action Purpose
Step 1 Shell > dir virtual-media-drive-name:
Displays all the file packages that exist in the specified virtual media drive. The drive name starts with fs0 and can be fs0, fs1, fs2, and so on.

Note
Make sure that you add a colon after the virtual media drive name. For example, dir fs1:

Step 2 Shell > virtual-media-drive-name:
Enters the virtual media drive in which the diagnostic file is located.

Step 3 Virtual Media Drive :\> cp package-file-name dsh.pkg
Copies the package file for which you are running diagnostics into the diagnostics shell package file.

Step 4 Virtual Media Drive :\> dsh
Enters the Diagnostics Shell. At the confirmation prompt, answer y.

Step 5 Server: SRV > run all
Executes all available diagnostic tests and displays the progress and status of the tests. Diagnostic tests are run on the server CPU, memory, and block devices. Block devices include hard drive, USB drive, and SD cards.

To execute a specific diagnostic test on the server, use the run test-name command where test-name can be one of the following:
cpux64—CPU diagnostic test.

diskx64—Block devices diagnostic test. Block devices include hard drive, USB drive, and SD cards.

memoryx64—Memory diagnostic test.

Note
Diagnostic tests can run for approximately 10 minutes.

Step 6 (Optional) Server: SRV > results
Displays a summary of the diagnostic test with Passed or Failed test status.

Note
The summary report indicates the number of tests that failed and passed. It does not provide information about which tests failed or passed. To determine which tests failed and passed, see the output of the run all command.

Step 7 (Optional) Server: SRV > show
Displays a list of global parameters and diagnostic test modules that were administered on the server.

Step 8 Server: SRV > exit
Exits from Diagnostic Shell.

Step 9 Open a service request with Cisco TAC.
If the diagnostic tests pass successfully, it indicates that there is no problem with the server CPU, memory, or block devices. The problem could be with some other hardware component or with the software configuration. Open a service request with Cisco TAC to isolate the problem.

If the diagnostic tests fail, open a service request with Cisco TAC for further assistance.
This example runs all diagnostic tests:
Shell > dir fs1:  
		06/27/12  07:48p            1,435,424  Dsh.efi
  06/27/12  08:03p               10,036  dsh-e140d.pkg
  06/25/12  06:00p               10,140  dsh-e140s.pkg
  06/27/12  08:04p               10,042  dsh-e160d.pkg
          4 File(s)   1,465,642 bytes
Shell > fs1:
fs1:\> cp dsh-e140d.pkg dsh.pkg
copying fs0:\OBD\dsh-e140d.pkg -> fs0:\OBD\dsh.pkg
- [ok]
fs1:\> dsh
Diagnostics is a standalone utility that runs on the server module independent
of the operating system or applications running on the module.All tests are
non-destructive, but there is a possibility of disk datacorruption during
power or equipment failure when the tests are in progress. Therefore, before
executing these tests, we highly recommend that you backup the data.


For questions or concerns with this utility, please open a Service Request
with Cisco TAC at http://www.cisco.com/cisco/web/support/index.html

(Y)es to continue test. (N)o to exit(y/n): Y
Cisco Diagnostics  Shell 1.03(0.3) Thu 06/28/-16:35:08.95-canis-diag@cisco.com
UCS-E140D-M1/K9:SRV>

Server: SRV > run all
Server: SRV > results
Test Name          : all
Test Status        : Passed
Failed/Run History : 0/17
Start Time         : 06/27/12 14:38:19
End Time           : 06/27/12 14:43:36
Diag Version       : 1.03(0.3) Mon 04/02/-17:07:57.19-canis-diag@cisco.com
Board S/N          : FOC160724BY

Server: SRV > show
Server: SRV > exit
What to Do Next

Reset the virtual media boot order to its original setting.