Contents

• Server Utilities
• Exporting Technical Support Data
• Rebooting CIMC
• Recovering from a Corrupted BIOS
• Resetting CIMC to Factory Defaults

Server Utilities

---

This chapter includes the following sections:

• Exporting Technical Support Data
• Rebooting CIMC
• Recovering from a Corrupted BIOS
• Resetting CIMC to Factory Defaults

Exporting Technical Support Data

Perform this task when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving a technical issue.

Procedure

---

Step 1	In the Navigation pane, click the Admin tab.
Step 2	On the Admin tab, click Utilities.
Step 3	In the Actions area of the Utilities pane, click Export Technical Support Data.
Step 4	In the Export Technical Support Data dialog box, complete the following fields: Name Description TFTP Server IP Address field The IP address of the TFTP server on which the support data file should be stored. Path and Filename field The name of the file in which the support data should be stored on the server. When you enter this name, include the relative path for the file from the top of the TFTP tree to the desired location.
Step 5	Click Export.

---

What to Do Next

Provide the generated report file to Cisco TAC.

Rebooting CIMC

On rare occasions, such as an issue with the current running firmware, troubleshooting a server may require you to reboot the CIMC. This procedure is not part of the normal maintenance of a server. After you reboot the CIMC, you are logged off and the CIMC will be unavailable for a few minutes.

Note	If you reboot the CIMC while the server is performing power-on self test (POST) or is operating in the Extensible Firmware Interface (EFI) shell, the server will be powered down until the CIMC reboot is complete.

Before You Begin

You must log in as a user with admin privileges to reboot the CIMC.

Procedure

---

Step 1	In the Navigation pane, click the Admin tab.
Step 2	On the Admin tab, click Utilities.
Step 3	In the Actions area of the Utilities pane, click Reboot CIMC.
Step 4	Click OK.

---

Recovering from a Corrupted BIOS

Before You Begin

• You must be logged in as admin to recover corrupt BIOS.

• Have the BIOS recovery ISO image ready. You will find the BIOS recovery ISO image under the Recovery folder of the firmware distribution package.

• Schedule some down time for the server because it will be powered cycled at the end of the recovery procedure.

Procedure

---

Step 1	In the Navigation pane, click the Server tab.
Step 2	On the server tab, click BIOS. The BIOS page appears.
Step 3	In the Actions area, click Recover Corrupt BIOS. The Recover Corrupt BIOS wizard appears.
Step 4	Use the Recover Corrupt BIOS wizard to recover your corrupt BIOS.

---

Resetting CIMC to Factory Defaults

On rare occasions, such as an issue with the current running firmware, troubleshooting a server may require you to reset the CIMC to the factory default. When this happens, all user-configurable settings are reset.

This procedure is not part of the normal server maintenance. After you reset the CIMC, you are logged off and must log in again. You may also lose connectivity and may need to reconfigure the network settings.

Before You Begin

You must log in as a user with admin privileges to reset the CIMC to factory defaults.

Procedure

---

Step 1	In the Navigation pane, click the Admin tab.
Step 2	On the Admin tab, click Utilities.
Step 3	In the Actions area of the Utilities pane, click Reset CIMC to Factory Default Configuration.
Step 4	Click OK. A reboot of CIMC while the host is performing BIOS POST (Power on Self Test) or is in EFI shell will turn off the host for a short amount of time. CIMC will power on when it is ready.

---