-
Catalyst 6500 Series Command Reference, 8.7
-
Quick Links to Catalyst 6500 Series Switch and ROM Monitor Commands
-
Preface
-
Command-Line Interfaces
-
alias to boot
-
cd to clear mls exclude protocol
-
clear mls multicast statistics to clear vtp statistics
-
clear web-auth to disconnect
-
download to enable
-
format to ping ethernet
-
pwd to reset-switch
-
restore counters to set critical recovery delay
-
set crypto key rsa to set macro
-
set macro ciscosmartports to set port auto-mdix
-
set port auxiliaryvlan to set rcp username
-
set rgmp to set spantree portvlanpri
-
set spantree priority to set trunk
-
set udld to set web-auth session-timeout
-
show accounting to show dot1q-all-tagged
-
show dot1x to show ip alias
-
show ip device-tracking to show ip permit
-
show ip route to show poll
-
show port to show snmp
-
show snmp access to show tech-support
-
show test to show users
-
show version to squeeze
-
stack to write tech-support
-
Acronyms
-
Acknowledgments for Open-Source Software
-
Table Of Contents
clear web-auth
To clear the configuration of the login or the login fail page, use the clear web-auth command.
clear web-auth {login-page | login-fail-page}
Syntax Description
login-page
Clears the configuration of the login page.
login-fail-page
Clears the configuration of the login Fail page.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to clear the configuration of the Login page:
Console> (enable) clear web-auth login-pageConsole> (enable)This example shows how to clear the configuration of the Login Fail page:
Console> (enable) clear web-auth login-fail-pageConsole> (enable)Related Commands
set port web-auth
set port web-auth initialize
set web-auth
set web-auth login-attempts
set web-auth login-fail-page
set web-auth login-page
set web-auth quiet-timeout
set web-auth session-timeout
show port web-auth
show web-auth summarycommit
To commit all ACEs or a specific ACE in NVRAM that has not been written to hardware, use the commit command.
commit qos acl {acl_name | all | adjacency}
commit security acl {acl_name | all | adjacency}
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
The commit command commits all ACEs in NVRAM that have not been written to hardware. Any committed ACL with no ACEs is deleted. We recommend that you enter ACEs in batches and enter the commit command to save all of them in hardware and NVRAM.
Examples
This example shows how to commit a specific QoS ACE to NVRAM:
Console> (enable) commit qos acl my_aclHardware programming in progress...ACL my_acl is committed to hardware.Console> (enable)This example shows how to commit a specific security ACE to NVRAM:
Console> (enable) commit security acl IPACL2ACL commit in progress.ACL IPACL2 is committed to hardware.Console> (enable)This example shows how to commit an adjacency table entry to NVRAM:
Console> (enable) commit security acl adjacencyCommit operation in progress.Adjacency successfully committed.Console> (enable)Related Commands
commit lda
To commit ASLB configuration that has not been written to hardware to NVRAM, use the commit lda command.
commit lda
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to commit ASLB configuration to NVRAM:
Console> (enable) commit ldaCommit operation in progress...Successfully committed Local Director Accelerator.Console> (enable)Related Commands
configure
To download a configuration file from an rcp server or the network and execute each command in that file, use the configure command.
configure {host file}[rcp]
configure network
Syntax Description
host
IP address or IP alias of the host.
file
Name of the file.
rcp
(Optional) Specifies rcp as the file transfer method.
network
Specifies interactive prompting for the host and the file.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
Refer to the Catalyst 6500 Series Switch Software Configuration Guide on how to construct a configuration file to download using the configure command.
Following is a sample file called system5.cfg in the /tftpboot directory:
beginshow timeset ip alias conc7 198.133.219.207set ip alias montreux 198.133.119.42set ip alias cres 192.122.174.42set prompt system5>set password# empty string old passwordpingpongpingpongend#Each line contains a command, except lines that begin with ! or #.
Examples
This example shows how to download the system5.cfg configuration file from the 192.122.174.42 host:
Console> (enable) configure 192.122.174.42 system5.cfgConfigure using system5.cfg from 192.122.174.42 (y/n) [n]? y/Done. Finished Network Download. (446 bytes)>> show timeWed May 19 1999, 17:42:50>> set ip alias conc7 198.133.219.207IP alias added.>> set ip alias montreux 198.133.219.40IP alias added.>> set ip alias cres 192.122.174.42IP alias added.>> set prompt system5>>> set passwordEnter old password:Enter new password: pingpongRetype new password: pingpongPassword changed.system5> (enable)Related Commands
confreg
To configure the configuration register utility, use the confreg command.
confreg [num]
Syntax Description
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Usage Guidelines
Executed with the confreg argument num, the VCR changes to match the number specified.
Without the argument, confreg dumps the contents of the VCR in English and allows you to alter the contents.
You are prompted to change or keep the information held in each bit of the VCR. In either case, the new VCR value is written into NVRAM and does not take effect until you reset or power cycle the platform.
You must issue a sync command to save your change. Otherwise, the change is not saved and a reset removes your change.
Examples
This example shows how to use the confreg command:
rommon 7 > confregConfiguration Summaryenabled are:console baud: 9600boot: the ROM Monitordo you wish to change the configuration? y/n [n]: yenable "diagnostic mode"? y/n [n]: yenable "use net in IP bcast address"? y/n [n]:enable "load rom after netboot fails"? y/n [n]:enable "use all zero broadcast"? y/n [n]:enable "break/abort has effect"? y/n [n]:enable "ignore system config info"? y/n [n]:change console baud rate? y/n [n]: yenter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400 [0]: 0change the boot characteristics? y/n [n]: yenter to boot:0 = ROM Monitor1 = the boot helper image2-15 = boot system[0]: 0Configuration Summaryenabled are:diagnostic modeconsole baud: 9600boot: the ROM Monitordo you wish to change the configuration? y/n [n]:You must reset or power cycle for new config to take effectRelated Commands
context
To display the context of a loaded image, use the context command.
context
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Usage Guidelines
The context from the kernel mode and process mode of a booted image are displayed, if available.
Examples
This example shows how to display the context of a loaded image:
rommon 6 > contextKernel Level Context:Reg MSW LSW | Reg MSW LSW------ ---------- ---------- | ----- ---------- ----------zero : 00000000 00000000 | s0 : 00000000 34008301AT : 00000000 3e800000 | s1 : 00000000 00000001v0 : 00000000 00000003 | s2 : 00000000 00000003v1 : 00000000 00000000 | s3 : 00000000 00000000a0 : 00000000 0000002b | s4 : 00000000 60276af8a1 : 00000000 00000003 | s5 : ffffffff ffffffffa2 : 00000000 00000000 | s6 : 00000000 60276c58a3 : 00000000 60276af8 | s7 : 00000000 0000000at0 : 00000000 00000b84 | t8 : 00000000 34008300t1 : 00000000 3e800004 | t9 : ffffffff ac000000t2 : 00000000 00000239 | k0 : 00000000 00000400t3 : 00000000 34008301 | k1 : 00000000 6024eb5ct4 : ffffffff ffff83fd | gp : 00000000 60252920t5 : 00000000 0000003f | sp : 00000000 60276a98t6 : 00000000 00000000 | s8 : 00000000 601fbf33t7 : ffffffff ffffffff | ra : 00000000 6006d380HI : 00000000 00000008 | LO : 00000000 00000000EPC : 00000000 60033054 | ErrPC : ffffffff bfc070c8Stat : 34408302 | Cause : 00002020Process Level Context:Reg MSW LSW | Reg MSW LSW------ ---------- ---------- | ----- ---------- ----------zero : 00000000 00000000 | s0 : 00000000 00000074AT : 00000000 3e820000 | s1 : 00000000 60276c58v0 : 00000000 00000081 | s2 : 00000000 601fbac0v1 : 00000000 00000074 | s3 : 00000000 00000036a0 : 00000000 00000400 | s4 : 00000000 0000000fa1 : 00000000 60276c58 | s5 : ffffffff ffffffffa2 : 00000000 00000074 | s6 : 00000000 60276c58a3 : 00000000 00000000 | s7 : 00000000 0000000at0 : 00000000 00000400 | t8 : 00000000 34008300t1 : 00000000 00000400 | t9 : ffffffff ac000000t2 : 00000000 00000000 | k0 : 00000000 30408401t3 : ffffffff ffff00ff | k1 : 00000000 30410000t4 : 00000000 600dcc10 | gp : 00000000 60252920t5 : 00000000 0000003f | sp : ffffffff 80007ce8t6 : 00000000 00000000 | s8 : 00000000 601fbf33t7 : ffffffff ffffffff | ra : 00000000 600dfd20HI : 00000000 00000008 | LO : 00000000 00000000EPC : 00000000 600dfd38 | ErrPC : ffffffff ffffffffStat : 34008303 | Cause : ffffffffcopy
To upload or download a flash image or a switch configuration to or from a flash device, rcp server, TFTP server, or an SCP server, use the copy command.
copy file-id {tftp | rcp | flash | file-id | config}
copy tftp {flash | file-id | config}
copy rcp {flash | file-id | config}
copy flash {tftp | rcp | file-id | config}
copy config {flash | file-id | tftp | rcp} [all]
copy acl config {flash | file-id | tftp | rcp}
copy cfg1 {tftp | rcp | flash | config | cfg2} [all]
copy cfg2 {tftp | rcp | flash | config | cfg1} [all]
copy ftp {flash | file-id | config}
copy scp destination
copy source scp
copy log-cmd {flash | ftp | rcp | scp | tftp | file-id}
copy sftp destination
copy source sftp
Syntax Description
Defaults
If a source or destination device is not given, the one specified by the cd command is used. If a destination filename is omitted, the source filename is used.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
Use the copy command to perform these tasks:
•
Download a system image or configuration file from a TFTP or rcp server to a flash device.
•
•
•
•
•
Caution
If you do not specify the source or destination device, the command uses the ones specified by the cd command. If you omit the destination filename, the source filename is used.
The copy config, copy cfg1, and copy cfg2 commands copy only nondefault commands to the destination configuration file. Use the keyword all to copy both default and nondefault configurations.
If you do not specify a source or destination flash device, the default flash device (specified by the cd command) is used. Use the pwd command to display the current default flash device. If you omit the destination filename, the system uses the source filename.
The system stores image and configuration files in the sysname.cfg file when you define a system name using the set system name command; otherwise, it uses the default myswitch.cfg file.
A colon (:) is required after the specified device.
If you use the flash keyword as the copy source or destination, you are prompted for the flash device name.
If you are copying a software image to multiple intelligent switching modules of the same type, use the flash keyword as the copy destination. The switch automatically determines which modules to copy the image to based on the header in the source image file. If you want to copy a software image to a single intelligent switching module in a switch with multiple modules of the same type, you must specify the destination file-id as m/bootflash: (do not specify a filename).
Before you begin downloading a software image using SCP, make sure of the following:
•
•
•
•
Before you attempt to upload a software image to an SCP server, do the following:
•
•
•
For more information about downloading and uploading files by using SCP, refer to Chapter 25, "Working with System Software Images," in the Catalyst 6500 Series Switch Software Configuration Guide.
The Secure File Transfer Protocol (SFTP) is available only in crypto images.
SFTP uses the SSH protocol for establishing a secure channel between the client and the server. SFTP is supported only with SSHv2. SFTP with SSHv1 is not supported.
SFTP client functionality is supported. SFTP server functionality is not supported.
Examples
This example shows how to use the copy command to upload the switch configuration to a file named cat.cfg on the slot0 flash device:
Console> (enable) copy config slot0:cat.cfgUpload configuration to slot0:cat.cfg649324 bytes available on device slot0, proceed (y/n) [n]? y............................................./Configuration has been copied successfully. (10200 bytes)Console> (enable)This example shows how to use the copy command to upload the switch configuration to a file named lab2.cfg on the TFTP server:
Console> (enable) copy config tftp:lab2.cfgIP address or name of remote host [172.20.22.7]? yUpload configuration to tftp:lab2.cfg (y/n) [n]? y............................/Configuration has been copied successfully. (10299 bytes).Console> (enable)This example shows how to use the copy command to upload the switch configuration to the cat.cfg file on the slot0 flash device:
Console> (enable) copy config flashFlash device [bootflash]? slot0:Name of file to copy to [test_image]? cat.cfgUpload configuration to slot0:cat.cfg749124 bytes available on device slot0, proceed (y/n) [n]? y..................................../Configuration has been copied successfully. (200345 bytes).Console> (enable)These examples show how to use the copy command to download a configuration from a TFTP server:
Console> (enable) copy slot0:cat.cfg configConfigure using slot0:cat.cfg (y/n) [n]? y/Finished download. (10900 bytes)>> set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set prompt Console>>> set length 24 defaultScreen length set to 24.>> set logout 20..........Console> (enable)Console> (enable) copy tftp configIP address or name of remote host? 172.20.22.7Name of configuration file? cat.cfgConfigure using cat.cfg from 172.20.22.7 (y/n) [n]? y/Finished network download. (10900 bytes)>> set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set prompt Console>>> set length 24 defaultScreen length set to 24.>> set logout 20...........Console> (enable)Console> (enable) copy flash configFlash device [bootflash]?Name of configuration file? test.cfgConfigure using bootflash:test.cfg (y/n) [n]? y/Finished download. (10900 bytes)>> set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70Password changed.>> set prompt Console>>> set length 24 defaultScreen length set to 24.>> set logout 20.....Console> (enable)This example shows how to copy the running configuration to an rcp server for storage:
Console> (enable) copy config rcpIP address or name of remote host []? 172.20.52.3Name of file to copy to []? cat6000_config.cfgUpload configuration to rcp:cat6000_config.cfg, (y/n) [n]? y............................................./Configuration has been copied successfully.Console> (enable)This example shows how to configure a Catalyst 6500 series switch using a configuration file downloaded from an rcp server:
Console> (enable) copy rcp configIP address or name of remote host []? 172.20.52.3Name of file to copy from []? dns-config.cfgConfigure using rcp:dns-config.cfg (y/n) [n]? y/Finished network download. (134 bytes)>>>> set ip dns server 172.16.10.70 primary172.16.10.70 added to DNS server table as primary server.>> set ip dns server 172.16.10.140172.16.10.140 added to DNS server table as backup server.>> set ip dns enableDNS is enabled>> set ip dns domain corp.comDefault DNS domain name set to corp.comConsole> (enable)This example shows how to upload an image from a remote host into flash using an rcp server:
Console> (enable) copy rcp flashIP address or name of remote host []? 172.20.52.3Name of file to copy from []? cat6000-sup-d.6-1-1.binFlash device [bootflash]?Name of file to copy to [cat6000-sup-d.6-1-1.bin]?4369664 bytes available on device bootflash, proceed (y/n) [n]? yCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCFile has been copied successfully.Console> (enable)This example shows how to download a configuration to the first startup configuration file (cfg1) on a supervisor engine:
Console> (enable) copy tftp cfg1IP address or name of remote host [172.20.32.10]?Name of file to copy from [/tftpboot/my.cfg]?Download config file from /tftpboot/my.cfg to cfg1 (y/n) [n]?.........File has been copied to cfg1.Console> (enable)This example shows how to copy the ACL configuration to a bootflash file manually:
Console> (enable) copy acl config bootflash:switchapp.cfgUpload configuration to bootflash:dan.cfg2843644 bytes available on device bootflash, proceed (y/n) [n]? y................../Configuration has been copied successfully.Console> (enable)This example shows a complete SCP download procedure of a crypto image to the switch:
Console> (enable) copy scp flashIP address or name of remote host []? 172.20.52.3Name of file to copy from []? cat6000-sup720cvk9.8-3-1.binFlash device [bootflash]?Name of file to copy to [cat6000-sup720cvk9.8-3-1.bin]?4369664 bytes available on device bootflash, proceed (y/n) [n]? yCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCFile has been copied successfully.Console> (enable) set boot system flash bootflash:cat6000-sup720cvk9.8-3-1.bin prependBOOT variable = bootflash:cat6000-sup720cvk9.8-3-1.bin,1;bootflash:cat6000-sup720cvk9.8-3-1.bin1-csx.bin,1;Console> (enable) reset systemThis command will reset the system.Do you want to continue (y/n) [n]? yConsole> (enable) 11/25/2003,13:51:39:SYS-5:System reset from Console//System Bootstrap, Version 4.2Copyright (c) 1994-2003 by cisco Systems, Inc.Presto processor with 32768 Kbytes of main memoryAutoboot executing command: "boot bootflash:cat6000-sup720cvk9.8-3-1.bin"CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCUncompressing file: ########################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################System Power On DiagnosticsDRAM Size ....................32 MBTesting DRAM..................PassedVerifying Text segment .......PassedNVRAM Size ...................512 KBSaving NVRAM .................Testing NVRAM ................PassedRestoring NVRAM...............Level2 Cache ..................PresentLevel2 Cache test..............PassedLeaving power_on_diagsCafe Daughter Present.EOBC link upBoot image: cat6000-sup720cvk9.8-3-1.binFlash Size = 0X1000000, num_flash_sectors = 64readCafe2Version: 0x00000001RIn Local Test Mode, Pinnacle Synch Retries: 2Running System Diagnostics from this Supervisor (Module 1)This may take up to 2 minutes....please waitCisco Systems ConsoleEnter password:11/25/2003,13:52:51:SYS-5:Module 1 is online11/25/2003,13:53:11:SYS-5:Module 4 is online11/25/2003,13:53:11:SYS-5:Module 5 is online11/25/2003,13:53:14:PAGP-5:Port 1/1 joined bridge port 1/1.11/25/2003,13:53:14:PAGP-5:Port 1/2 joined bridge port 1/2.11/25/2003,13:53:40:SYS-5:Module 2 is online11/25/2003,13:53:45:SYS-5:Module 3 is onlineConsole> (enable)This example shows how to upload the crypto image to an SCP server:
Console> (enable) copy bootflash scpFlash device [bootflash]? slot0:Name of file to copy from []? cat6000-sup720cvk9.8-3-1.binIP address or name of remote host [172.20.52.3]? 172.20.52.10Name of file to copy to [cat6000-sup720cvk9.8-3-1.bin]?CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC|File has been copied successfully.Console> (enable)Related Commands
clear ftp
configure
reset—switch
set boot config-register
set boot config-register auto-config
set boot system flash
set ftp
show ftp
writecopy tech-support
To copy the output of the show tech-support command to the target device (ftp or tftp or file-id), use the copy tech-support command.
copy tech-support {ftp | tftp | file-id}
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to copy the output of the show tech-support command to an FTP server:
Console> (enable) copy tech-support ftpIP address or name of remote host []? 10.77.11.190Username for ftp[anonymous]? cat6kPassword for User cat6k[ ]:Name of file to copy to [/tftp/bodc-cat6k/cat/cc]?Upload tech-support to ftp:/tftp/bodc-cat6k/cat/cc (y/n) [n]? yWriting /tftp/bodc-cat6k/cat/cc!!!!!!!!!!!!!!!!!!!!!!!!!!Tech-support has been copied successfully.Console> (enable)This example shows how to copy the output of the show tech-support command to a TFTP server:
Console> (enable) copy tech-support tftpIP address or name of remote host [ ]? 10.77.11.190Name of file to copy to [ ]? /tftp/bodc-cat6k/cat/ccUpload tech-support to tftp:/tftp/bodc-cat6k/cat/cc (y/n) [n]? yTech-support has been copied successfully.Console> (enable)This example shows how to copy the output of the show tech-support command to the filename techsupport:
Console> (enable) copy tech-support 6/bootdisk:techsupportUpload tech-support to bootdisk:techsupport232480768 bytes available on device bootdisk, proceed (y/n) [n]? yTech-support has been copied successfully.Console> (enable)Related Commands
delete
To delete a configuration file, use the delete command.
delete [[m/]device:]filename
Syntax Description
m/
(Optional) Module number of the supervisor engine containing the flash device.
device:
(Optional) Device where the flash resides.
filename
Name of the configuration file.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
A colon (:) is required after the specified device.
Examples
This example shows how to delete the cat6000-sup-d.5-5-1.bin configuration file from the flash device and then verify the deletion by entering the show flash command:
Console> (enable) delete bootflash:cat6000-sup-d.5-5-1.binConsole> (enable)Console> (enable) show flash-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name1 .D ffffffff 5415406e 3300b8 25 3080247 Jan 12 2000 13:22:46 cat6000-sup-d.6-1-1.bin2 .. ffffffff 762950d6 6234d0 25 3093399 Jan 13 2000 12:33:14 cat6000-sup-d.6-1-1.bin1428272 bytes available (6173904 bytes used)Console> (enable)Related Commands
dir—switch
show flash
squeeze
undelete
dev
To list the device IDs available on a switch, use the dev command.
dev
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Examples
This example shows how to use the dev command:
rommon 10 > devDevices in device table:id namebootflash: bootflashslot0: PCMCIA slot 0eprom: epromdiagnostic start
To start running a specific test based on test ID numbers, use the diagnostic start command.
diagnostic start module mod_num test {all | test_ID_num | test_list | complete | minimal | non-disruptive | per-port} [port {all | port_num | port_list}]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
The diagnostic start command accepts one test ID, a range of test IDs, a subgroup of tests, or all for all tests. The test ID for a particular test can be different from one module type to another module type or even from one software release to another software release. You need to obtain the correct test ID and relevant test name using by the show diagnostic content command.
To configure generic online diagnostics, use the set commands in the "Related Commands" section.
Note
Examples
This example shows how to start online diagnostic test 1 on module 5:
Console> diagnostic start module 5 test 12005 Aug 18 15:10:08 %DIAG-6-TEST_RUNNING:Module 5: Running FirmwareDiagStatus{ID=1} ...2005 Aug 18 15:10:08 %DIAG-6-TEST_OK:Module 5: FirmwareDiagStatus{ID=1} has completed successfullyConsole>Related Commands
clear diagnostic
set diagnostic bootup level
set diagnostic diagfail-action
set diagnostic event-log size
set diagnostic monitor
set diagnostic ondemand
set diagnostic schedule
show diagnosticdiagnostic stop
To stop running generic online diagnostics on a specified module, use the diagnostic stop command.
diagnostic stop module mod_num
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
Because some memory tests might take hours to complete, if you want to stop them before they conclude, use this command.
Note
Examples
This example shows the output when you enter the diagnostic stop command, but no test is running:
Console> diagnostic stop module 5Diagnostic[Module 5]: Diagnostic is not active.2005 Aug 18 15:38:30 %DIAG-3-NO_DIAG_RUNNING:Module 5: Diagnostic is not runningConsole>Related Commands
clear diagnostic
set diagnostic bootup level
set diagnostic diagfail-action
set diagnostic event-log size
set diagnostic monitor
set diagnostic ondemand
set diagnostic schedule
show diagnosticdir—ROM monitor
To list the files of the named device, use the dir command.
dir device
Syntax Description
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Examples
This example shows how to use the dir command:
rommon 11 > dir flash:File size Checksum File name65 bytes (0x41) 0xb49d clev/oddfile652229799 bytes (0x220627) 0x469e clev/sierra-k.Zdir—switch
To display a list of files on a flash memory device, use the dir command.
dir [[m/]device:][filename] [all | deleted | long]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal and privileged.
Usage Guidelines
A colon (:) is required after the specified device.
When you specify the all keyword, the file information is displayed in long format.
When you omit all keywords (all, deleted, or long), the system displays file information in short format. Short format is shown in Table 2-11.
Table 2-11 Short Format
#
File index number
length
File length
date/time
Date and time the file was created
name
Filename
When you use one of the keywords (all, deleted, or long), the system displays file information in long format. The long format is shown in Table 2-12.
Examples
This example shows how to display the file information in short format:
Console> (enable) dir-#- -length- -----date/time------ name1 6061822 Mar 03 2000 15:42:49 cat6000-sup.6-1-1.bin2 6165044 Mar 13 2000 14:40:15 cat6000-sup.5-5-1.bin3763660 bytes available (12227124 bytes used)Console> (enable)This example shows how to display the file information in long format:
Console> (enable) dir long-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name1 .. ffffffff f3a3e7c1 607f80 24 6061822 Mar 03 2000 15:42:49 cat6000-sup.6-1-1.bin2 .. ffffffff aa825ac6 be9234 24 6165044 Mar 13 2000 14:40:15 cat6000-sup.5-5-1.bin3763660 bytes available (12227124 bytes used)Console> (enable)Related Commands
disable
To return to normal mode from privileged mode, use the disable command.
disable
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to return to normal mode:
Console> (enable) disableConsole>Related Commands
disconnect
To close a session by session ID number, use the disconnect command.
disconnect session_id
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
To identify session ID numbers, enter the show users command.
Examples
This example shows how to close a session by entering the session ID number:
Console> (enable) disconnect 2Telnet session from cbin3-view2.cisco.com disconnected.Console> (enable)Related Commands
