Table Of Contents

Configuring Layer 3 Protocol Filtering

Understanding How Layer 3 Protocol Filtering Works

Default Layer 3 Protocol Filtering Configuration

Configuring Layer 3 Protocol Filtering on the Switch

Enabling Layer 3 Protocol Filtering

Disabling Layer 3 Protocol Filtering

Configuring Layer 3 Protocol Filtering

---

This chapter describes how to configure Layer 3 protocol filtering on Ethernet, Fast Ethernet, and Gigabit Ethernet ports on the Catalyst 6500 series switches.

---

Note For complete syntax and usage information for the commands used in this chapter, refer to the Catalyst 6500 Series Switch Command Reference publication.

---

This chapter consists of these sections:

•Understanding How Layer 3 Protocol Filtering Works

•Default Layer 3 Protocol Filtering Configuration

•Configuring Layer 3 Protocol Filtering on the Switch

Understanding How Layer 3 Protocol Filtering Works

Layer 3 protocol filtering prevents certain protocol traffic from being forwarded out switch ports. Layer 3 protocol filtering is implemented on the supervisor engine and does not require a Policy Feature Card (PFC) or Multilayer Switch Feature Card (MSFC). Broadcast and unicast flood traffic is filtered based on the membership of ports in different protocol groups. This filtering is in addition to the filtering that is provided by port-VLAN membership. Layer 3 protocol filtering is supported only on nontrunking Ethernet, Fast Ethernet, and Gigabit Ethernet ports.

Trunking ports are always members of all protocol groups. To avoid compatibility issues with other networking devices, Layer 3 protocol filtering is not performed on trunk ports. Layer 2 protocols, such as Spanning Tree Protocol (STP) and Cisco Discovery Protocol (CDP), are not affected by Layer 3 protocol filtering. Dynamic ports and ports that have port security enabled are members of all protocol groups.

You can configure a port with any one of these modes for each protocol group: on, off, or auto.

If the configuration is set to on, the port receives all the flood traffic for that protocol. If the configuration is set to off, the port does not receive any flood traffic for that protocol.

If the configuration is set to auto, the port is added to the group only after packets of the specific protocol are received on that port. With autolearning, ports become members of the protocol group only after receiving packets of the corresponding protocol from the device that is attached to that port. Autoconfigured ports are removed from the protocol group if no packets are received for that protocol within 60 minutes. Ports are also removed from the protocol group when the supervisor engine detects that the link is down on the port.

For example, if a host that supports both IP and Internetwork Packet Exchange (IPX) is connected to a switch port that is configured as auto for IPX, but the host is transmitting only IP traffic, the port to which the host is connected will not forward any IPX flood traffic to the host. However, if the host sends an IPX packet, the supervisor engine software detects the protocol traffic and the port is added to the IPX group, allowing the port to receive IPX flood traffic. If the host stops sending IPX traffic for more than 60 minutes, the port is removed from the IPX protocol group.

By default, ports are configured to on for the IP protocol group. Typically, you should only configure a port to auto for IP if there is a directly connected end station out the port. The default port configuration for IPX and Group is auto.

With Layer 3 protocol filtering enabled, ports are identified on a protocol basis. A port can be a member of one or more protocol groups. Flood traffic for each protocol group is forwarded out a port only if that port belongs to the appropriate protocol group.

Packets are classified into the following protocol groups:

•IP

•IPX

•AppleTalk, DECnet, and Banyan VINES (group mode)

•Packets not belonging to any of these protocols

Default Layer 3 Protocol Filtering Configuration

Table 33-1 shows the default Layer 3 protocol filtering configuration.

Table 33-1 Layer 3 Protocol Filtering Default Configuration

Feature	Default Value
Layer 3 protocol filtering	Disabled
ip mode	on
ipx mode	auto
group mode	auto

Configuring Layer 3 Protocol Filtering on the Switch

These sections describe how to configure Layer 3 protocol filtering on Ethernet-type VLANs and on any type of Ethernet port:

•Enabling Layer 3 Protocol Filtering

•Disabling Layer 3 Protocol Filtering

Enabling Layer 3 Protocol Filtering

To enable Layer 3 protocol filtering on Ethernet ports, perform this task in privileged mode:

	Task	Command
Step 1	Enable Layer 3 protocol filtering on the switch.	set protocolfilter enable
Step 2	Set the protocol membership of the desired ports.	set port protocol mod/port {ip | ipx | group} {on | off | auto}
Step 3	Verify the port filtering configuration.	show port protocol [mod[/port]]

This example shows how to enable Layer 3 protocol filtering, set the protocol membership of ports, and verify the configuration:

Console> (enable) set protocolfilter enable

Protocol filtering enabled on this switch.

Console> (enable) set port protocol 7/1-4 ip on

IP protocol set to on mode on ports 7/1-4.

Console> (enable) set port protocol 7/1-4 ipx off

IPX protocol disabled on ports 7/1-4.

Console> (enable) set port protocol 7/1-4 group auto

Group protocol set to auto mode on ports 7/1-4.

Console> (enable) show port protocol 7/1-4

Port     Vlan       IP       IP Hosts IPX      IPX Hosts Group    Group Hosts

-------- ---------- -------- -------- -------- --------- -------- -----------

7/1     4           on       1        off      0         auto-off 0          

7/2     5           on       1        off      0         auto-on  1          

7/3     2           on       1        off      0         auto-off 0          

7/4     4           on       1        off      0         auto-on  1          

Console> (enable) 

Disabling Layer 3 Protocol Filtering

To disable Layer 3 protocol filtering on the switch, perform this task in privileged mode:

Task	Command
Disable Layer 3 protocol filtering.	set protocolfilter disable

This example shows how to disable Layer 3 protocol filtering:

Console> (enable) set protocolfilter disable

Protocol filtering disabled on this switch.

Console> (enable)