Software Configuration Guide (5.5)
Working With System Software Images
Download this chapter
Working With System Software ImagesWorking With System Software Images
give_us_feedback

Table Of Contents

Working with System Software Images

Downloading System Software Images to the Switch Using TFTP

Understanding How TFTP Software Image Downloads Work

Preparing to Download an Image Using TFTP

Downloading Supervisor Engine Images Using TFTP

Downloading Switching Module Images Using TFTP

Example TFTP Download Procedures

Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

Example Single Module Image TFTP Download (Supervisor III or III F)

Example Single Intelligent Module Image TFTP Download (Catalyst 5000 Family Supervisor II, II G, or III G)

Example Multiple Module Image TFTP Download (Supervisor III or III F)

Example Multiple Module Image TFTP Download (Supervisor II, II G, or III G)

Uploading System Software Images to a TFTP Server

Preparing to Upload an Image to a TFTP Server

Uploading Software Images to a TFTP Server

Downloading System Software Images to the Switch Using rcp

Understanding How rcp Software Image Downloads Work

Preparing to Download an Image Using rcp

Downloading Supervisor Engine Images Using rcp

Downloading Switching Module Images Using rcp

Example rcp Download Procedures

Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

Example Single Module Image rcp Download (Supervisor III or III F)

Example Single Intelligent Module Image rcp Download (Catalyst 5000 Family Supervisor II, II G,
or III G)

Example Multiple Module Image rcp Download (Supervisor III or III F)

Example Multiple Module Image rcp Download (Supervisor II, II G, or III G)

Uploading System Software Images to an rcp Server

Preparing to Upload an Image to an rcp Server

Uploading Software Images to an rcp Server

Downloading Software Images over a Serial Connection on the Console Port

Preparing to Download an Image Using Kermit

Downloading Software Images Using Kermit (PC Procedure)

Downloading Software Images Using Kermit (UNIX Procedure)

Example Serial Software Image Download Procedures

Example PC Serial Download Procedure

Example UNIX Workstation Serial Download Procedure


Working with System Software Images

This chapter describes how to work with system software image files.

Note For complete syntax and usage information for the commands used in this chapter, refer to the Command Reference publication for your switch.

This chapter consists of these sections:

•Downloading System Software Images to the Switch Using TFTP

•Uploading System Software Images to a TFTP Server

•Downloading System Software Images to the Switch Using rcp

•Uploading System Software Images to an rcp Server

•Downloading Software Images over a Serial Connection on the Console Port

Downloading System Software Images to the Switch Using TFTP

These sections describe how to download system software images to the switch supervisor engine and to intelligent modules:

•Understanding How TFTP Software Image Downloads Work

•Preparing to Download an Image Using TFTP

•Downloading Supervisor Engine Images Using TFTP

•Downloading Switching Module Images Using TFTP

•Example TFTP Download Procedures

Understanding How TFTP Software Image Downloads Work

You can download system software images to the switch using the Trivial File Transfer Protocol (TFTP). TFTP allows you to download system image files over the network from a TFTP server.

Some modules, such as Catalyst 5000 family FDDI and ATM modules, have their own onboard Flash. When you download a software image file, the switch checks the header of the image file to determine the type of software image.

Depending on the type of software image you are downloading, one of the following occurs:

•Supervisor engine software image—The image file is downloaded to the supervisor engine Flash memory. On the Catalyst 5000 family Supervisor Engine II, II G, and III G, you can store only a single image file at a time. On the Catalyst 5000 family Supervisor Engine III and III F, and on the Catalyst 4000 family, 2926G series, 2948G, and 2980G switches, you can store multiple image files on the Flash memory system devices (such as boot Flash and, on the Supervisor Engine III and Catalyst 2926G series switches, Flash PC cards).

Caution Some supervisor engine software releases update the supervisor engine erasable programmable logic devices (EPLDs). The EPLDs can be updated only a limited number of times. You should avoid loading a new software release and then backing out unnecessarily. The supervisor engine software release notes indicate which software releases have code that updates the EPLDs.

•Intelligent module software images—If you specified a module number, the image file is downloaded to the specified module only (provided the image file is designed for the specified module type). If you do not specify a module number, the image file is downloaded to every module of the appropriate type. The file is relayed packet by packet to the appropriate modules using the Inter-Process Communications protocol internal to the system, with communication taking place across the switching bus. Downloading a software image to multiple modules significantly speeds up the process of updating the software on multiple modules of the same type.

Note For more information on working with system software image files on the Flash file system, refer to "Using the Flash File System."

Preparing to Download an Image Using TFTP

Before you begin downloading a software image using TFTP, make sure of the following:

•Ensure that the workstation acting as the TFTP server is configured properly.

•Ensure that the switch has a route to the TFTP server. The switch and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the TFTP server using the ping command.

•Ensure that the software image to be downloaded is in the correct directory on the TFTP server (for example, /tftpboot on a UNIX workstation).

•Ensure that the permissions on the file are set correctly. Permissions on the file should be at least read for the specific username. Note that if you are not using a Telnet session with a valid username, you can use the set rcp username command to specify a valid username

•A power interruption (or other problem) during the download procedure can corrupt the Flash code. If the Flash code is corrupted, you can connect to the switch through the console port. On the Catalyst 5000 family Supervisor Engine II, II G, and III G, and on the Catalyst 4000 family, 2948G, and 2980G switches, you can download the Flash code again through an enabled port in VLAN 1. By default, port 1/1 is enabled. You can use port 1/1 or enable another port. On the Catalyst 5000 family Supervisor Engine III and the Catalyst 2926G series switches, you can boot from an uncorrupted system image on a Flash PC card.

Downloading Supervisor Engine Images Using TFTP

Note Catalyst 5500 series only—If you have a redundant supervisor engine, you cannot download a system image directly from a TFTP server to the Flash memory on the standby supervisor engine. When you download the image to the active supervisor engine, the standby supervisor engine synchronizes automatically with the new image. In addition, you cannot copy an image from the standby supervisor engine to the active supervisor engine.

Use the following procedure to download a supervisor engine software image to the switch from a TFTP server:

Step 1 Copy the software image file to the appropriate TFTP directory on the workstation.

Step 2 Log into the switch through the console port or through a Telnet session. If you log in using Telnet, your Telnet session disconnects when you reset the switch to run the new software.

Step 3 Use the command appropriate for your switch and supervisor engine to download the software image from the TFTP server:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—Use the copy tftp flash command. When prompted, enter the IP address or host name of the TFTP server and the name of the file to download. On those platforms that support the Flash file system, you are also prompted for the Flash device to which to copy the file and the destination filename.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—Use the download host file command, where host is the IP address or host name of the workstation acting as the TFTP server and file is the name of the file to download.

Note The Supervisor Engine III F and the Catalyst 4000 family, 2948G, and 2980G switches have only one Flash device (bootflash:).

The switch downloads the image file from the TFTP server:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—The image is copied to the specified Flash device.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—The Flash memory on the supervisor engine is erased and reprogrammed with the downloaded Flash code.

Note The switch remains operational while the image downloads.

Step 4 Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000, 2926G series, 2948G, and 2980G switches—Modify the BOOT environment variable using the set boot system flash device:filename prepend command, so that the new image boots when you reset the switch. Specify the Flash device (device:) and the filename of the downloaded image (filename).

Note This step is not necessary on the Catalyst 5000 family Supervisor Engine II, II G, and III G.

Step 5 Reset the switch using the reset system command. If you are connected to the switch through Telnet, your Telnet session disconnects.

During startup, on the Catalyst 5000 family Supervisor Engine III and III F, and on the Catalyst 4000 family, 2926G series, 2948G, and 2980G switches, the Flash memory on the supervisor engine is reprogrammed with the new Flash code.

Step 6 When the switch reboots, enter the show version command to check the version of the code on the switch.

Note For examples that show complete TFTP download procedures for the various supervisor engine and switch types, see the "Example TFTP Download Procedures" section.

Downloading Switching Module Images Using TFTP

Use this procedure to download a software image to an intelligent module on a Catalyst 5000 family switch:

Step 1 Copy the software image file to the appropriate TFTP directory on the workstation.

Step 2 Log into the switch through the console port or a Telnet session. If you log in using Telnet, your Telnet session might disconnect when you reset modules to run the new software.

Step 3 Use the command appropriate for your switch and supervisor engine to download the software image from the TFTP server:

•Catalyst 5000 family Supervisor Engine III and III F

–If there is only one module of the type appropriate for the image, or if there are multiple modules of the same type and you want to update the image on all of them, use the copy tftp flash command. When prompted, enter the IP address or host name of the TFTP server, the name of the file to download, the Flash device to which to copy the file, and the destination filename.

–If there are multiple modules of the type appropriate for the image but you only want to update a single module, use the copy tftp m/bootflash: command, where m is the number of the module to which to download the software image.

•Catalyst 5000 family Supervisor Engine II, II G, and III G

–If there is only one module of the type appropriate for the image, or if there are multiple modules of the same type and you want to update the image on all of them, use the download host file command, where host is the IP address or host name of the TFTP server and file is the name of the file to download.

–If there are multiple modules of the type appropriate for the image but you only want to update a single module, use the download host file mod_num command, where mod_num is the slot in which the module is installed.

Note If you do not specify a module number, the switch examines the header of the image file to determine to which modules the software is downloaded. The image is then downloaded to all the modules of that type.

The switch downloads the image file, erases the Flash memory on the appropriate modules, and reprograms the Flash memory with the downloaded Flash code.

Note All modules in the switch remain operational while the image downloads.

Step 4 Reset the appropriate modules using the reset mod_num command. If you are connected through Telnet, your Telnet session disconnects if you reset the module through which your connection was made.

Step 5 When the upgraded modules come online, enter the show version [mod_num] command to check the version of the code on the switch.

Note For examples that show complete procedures for TFTP downloads to intelligent modules, see the "Example Single Intelligent Module Image TFTP Download (Catalyst 5000 Family Supervisor II, II G, or III G)" section, the "Example Multiple Module Image TFTP Download (Supervisor II, II G, or III G)" section, the "Example Single Module Image TFTP Download (Supervisor III or III F)" section, and the "Example Multiple Module Image TFTP Download (Supervisor III or III F)" section.

Example TFTP Download Procedures

These sections show example TFTP download procedures:

•Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

•Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

•Example Single Module Image TFTP Download (Supervisor III or III F)

•Example Single Intelligent Module Image TFTP Download (Catalyst 5000 Family Supervisor II, II G, or III G)

•Example Multiple Module Image TFTP Download (Supervisor III or III F)

•Example Multiple Module Image TFTP Download (Supervisor II, II G, or III G)

Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

Note For a step-by-step procedure for downloading a supervisor engine software image from a TFTP server, see the "Downloading Supervisor Engine Images Using TFTP" section.

This example shows a complete TFTP download procedure of a supervisor engine software image to a Catalyst 5000 family switch with a Supervisor Engine III or III F module, or to a Catalyst 4000 family, 2926G series, 2948G, or 2980G switch: 

Console> (enable) show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5530   007451586 Hw : 1.3

                              Fw : 3.1.2

                              Fw1: 3.1(2)

                              Sw : 4.1(2)

Console> (enable) copy tftp flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-sup3.4-2-1.bin

Flash device [bootflash]?

Name of file to copy to [cat5000-sup3.4-2-1.bin]?

4369664 bytes available on device bootflash, proceed (y/n) [n]? y

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCC

File has been copied successfully.

Console> (enable) set boot system flash bootflash:cat5000-sup3.4-2-1.bin prepend

BOOT variable = bootflash:cat5000-sup3.4-2-1.bin,1;bootflash:cat5000-sup3.4-1

-2.bin,1;

Console> (enable) reset system

This command will reset the system.

Do you want to continue (y/n) [n]? y

Console> (enable) 07/21/1998,13:51:39:SYS-5:System reset from Console//


System Bootstrap, Version 3.1(2)

Copyright (c) 1994-1997 by cisco Systems, Inc.

Presto processor with 32768 Kbytes of main memory

Autoboot executing command: "boot bootflash:cat5000-sup3.4-2-1.bin"

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCC

Uncompressing file:  ###########################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

#############

System Power On Diagnostics

NVRAM Size .. .................512KB

ID Prom Test ..................Passed

DPRAM Size ....................16KB

DPRAM Data 0x55 Test ..........Passed

DPRAM Data 0xaa Test ..........Passed

DPRAM Address Test ............Passed

Clearing DPRAM ................Done

System DRAM Memory Size .......32MB

DRAM Data 0x55 Test ...........Passed

DRAM Data 0xaa Test ...........Passed

DRAM Address Test  ............Passed

Clearing DRAM .................Done

EARL++ ........................Present

EARL RAM Test .................Passed

EARL Serial Prom Test .........Passed

Level2 Cache ..................Present

Level2 Cache test..............Passed

Boot image: bootflash:cat5000-sup3.4-2-1.bin

Downloading epld sram device please wait ...

Programming successful for Altera 10K10 SRAM EPLD

Downloading epld sram device please wait ...

Programming successful for Altera 10K30 SRAM EPLD

Downloading epld sram device please wait ...

Cisco Systems Console

Enter password:

07/21/1998,13:52:51:SYS-5:Module 1 is online

07/21/1998,13:53:11:SYS-5:Module 4 is online

07/21/1998,13:53:11:SYS-5:Module 5 is online

07/21/1998,13:53:14:PAGP-5:Port 1/1 joined bridge port 1/1.

07/21/1998,13:53:14:PAGP-5:Port 1/2 joined bridge port 1/2.

07/21/1998,13:53:40:SYS-5:Module 2 is online

07/21/1998,13:53:45:SYS-5:Module 3 is online

Console> show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5530   007451586 Hw : 1.3

                              Fw : 3.1.2

                              Fw1: 3.1(2)

                              Sw : 4.2(1)

Console>

Example Supervisor Image TFTP Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

Note For a step-by-step procedure for downloading a supervisor engine software image from a TFTP server, see the "Downloading Supervisor Engine Images Using TFTP" section.

This example shows a complete TFTP download procedure of a supervisor engine software image to a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5509   007486003 Hw : 2.3

                              Fw : 3.1(2)

                              Fw1: 3.1(1)

                              Sw : 4.1(2)

Console> (enable) download 172.20.52.3 cat5000-supg.5-2-1.bin

Download image cat5000-supg.5-2-1.bin from 172.20.52.3 to module 1 FLASH 

(y/n) [n]? y

/

Finished network single module download. (4104180 bytes)

Erasing flash sector...done.

Programming flash sector...done.

Verifying Flash Image ...

The system needs to be reset to run the new image.

Console> (enable) reset

This command will reset the system.

Do you want to continue (y/n) [n]? y

%SYS-5-SYS_RESET:System reset from Console//


Console> (enable) 



ATE0

ATS0=1



ROM Power Up Diagnostics of Apr 20 1999


Init NVRAM Log 

LED Test  ................... done

ROM Checksum  ............... passed

Dual Port RAM r/w Test  ..... passed

ID PROM  .................... passed

System DRAM Size(mb)  ....... 32

DRAM Data Bus Test  ......... passed

DRAM Address Test  .......... passed

DRAM Byte/Word Access Test .. passed



BOOTROM Version 5.1(1), Dated Apr 20 1999 11:09:48

BOOT date: 09/01/99 BOOT time: 14:33:03

uncompressing nmp image

This will take a minute...

NMP image is successfully uncompressed in DRAM


Running System Diagnostics from this Supervisor (Module 1)

This may take up to 2 minutes....please wait



Cisco Systems Console




Enter password: 

%MLS-5-MLSENABLED:IP Multilayer switching is enabled

%MLS-5-NDEDISABLED:Netflow Data Export disabled

%SYS-5-MOD_OK:Module 1 is online

%SYS-5-MOD_OK:Module 9 is online

%SYS-5-MOD_OK:Module 3 is online

%SYS-5-MOD_OK:Module 7 is online

%SYS-5-MOD_OK:Module 6 is online


Console> show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5550   013490945 Hw : 1.1

                              Fw : 5.1(1)

                              Fw1: 5.1(1)

                              Sw : 5.2(1)

Console>

Example Single Module Image TFTP Download (Supervisor III or III F)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine III or III F, refer to the "Downloading Switching Module Images Using TFTP" section.

This example shows a complete TFTP download procedure of an ATM software image to a single ATM module in a Catalyst 5000 family switch with a Supervisor Engine III or III F module: 

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) copy tftp 4/flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-atm.3-2-7.bin

Download image tftp:cat5000-atm.3-2-7.bin to Module 4 FLASH (y/n) [n]? y

This command will reset Download Module(s) you selected.

Do you wish to continue download flash (y/n) [n]? y

-

Download done for module 4, please wait for it to come online

File has been copied successfully.

Console> (enable) 07/21/1998,13:13:54:SYS-5:Module 4 is online

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Example Single Intelligent Module Image TFTP Download (Catalyst 5000 Family Supervisor II, II G, or III G)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G, refer to the "Downloading Switching Module Images Using TFTP" section.

This example shows a complete TFTP download procedure of an FDDI software image to a single FDDI module in a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 3

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

3   2    WS-X5101   003489788 Hw : 1.0

                              Fw : 1.1

                              Fw1: 1.3

                              Sw : 2.1(7)

Console> (enable) download 172.20.52.3 cat5000-fddi.3-1-1.bin 3

This command will reset module 3.

Download image cat5000-fddi.3-1-1.bin from 172.20.52.3 to Module 3 FLASH (y/n) [

n]? y

|

Finished network single module download. (1060456 bytes)

...............................................................................

...............................................................................

...............................................................................

...............................................................................

...............................................................................

..................................

SCP download checksum ok

SCP download done.

Please wait until module 3 comes online before resetting.

(Approximately 5 minutes)

Console> (enable) Console> (enable) 07/21/1998,11:23:36:SYS-5:Module 3 FLASH pro

gramming complete

07/21/1998,11:24:59:SYS-5:Module 3 is online

07/21/1998,11:25:00:DTP-5:Port 3/1-2 has become dot10 trunk

Console> (enable) show version 3

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

3   2    WS-X5101   003489788 Hw : 1.0

                              Fw : 1.1

                              Fw1: 1.3

                              Sw : 3.1(1)

Console> (enable)

Example Multiple Module Image TFTP Download (Supervisor III or III F)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine III or III F, refer to the "Downloading Switching Module Images Using TFTP" section.

This example shows a complete TFTP download procedure of an ATM software image to multiple ATM modules in a Catalyst 5000 family switch with a Supervisor Engine III or III F module: 

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) show version 5

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

5   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) copy tftp flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-atm.3-2-7.bin

Download image tftp:cat5000-atm.3-2-7.bin to Module 4 FLASH (y/n) [n]? y

Download image tftp:cat5000-atm.3-2-7.bin to Module 5 FLASH (y/n) [n]? y

This command will reset Download Module(s) you selected.

Do you wish to continue download flash (y/n) [n]? y

-

Download done for module 4, please wait for it to come online

Download done for module 5, please wait for it to come online

File has been copied successfully.

Console> (enable) 07/21/1998,12:25:10:SYS-5:Module 4 is online

07/21/1998,12:25:10:SYS-5:Module 5 is online

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable) show version 5

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

5   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Example Multiple Module Image TFTP Download (Supervisor II, II G, or III G)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G, refer to the "Downloading Switching Module Images Using TFTP" section.

This example shows a complete TFTP download procedure of an ATM software image to multiple ATM modules in a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 8

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

8   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(4)

Console> (enable) show version 9

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

9   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) download 172.20.52.3 cat5000-atm.3-2-7.bin

Download image cat5000-atm.3-2-7.bin from 172.20.52.3 to Module 8 FLASH (y/n) [n

]? y

Download image cat5000-atm.3-2-7.bin from 172.20.52.3 to Module 9 FLASH (y/n) [n

]? y

This command will reset download module(s) you selected.

Do you wish to continue download to flash (y/n) [n]? y

-

Download done for module 8, please wait for it to come online

Download done for module 9, please wait for it to come online

Finished network multiple modules download. (2378316 bytes)

Please wait until module(s) come online before resetting.

Console> (enable) 07/21/1998,13:19:54:SYS-5:Module 8 is online

07/21/1998,13:19:54:SYS-5:Module 9 is online

Console> (enable) show version 8

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

8   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable) show version 9

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

9   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Uploading System Software Images to a TFTP Server

These sections describe how to upload system software images from a switch to a TFTP server:

•Preparing to Upload an Image to a TFTP Server

•Uploading Software Images to a TFTP Server

Note For more information on working with system software image files on the Flash file system, see "Using the Flash File System."

Preparing to Upload an Image to a TFTP Server

Before you attempt to upload a software image to a TFTP server, do the following:

•Ensure that the workstation acting as the TFTP server is configured properly.

•Ensure that the switch has a route to the TFTP server. The switch and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the TFTP server using the ping command.

•You might need to create an empty file on the TFTP server before uploading the image. On a UNIX workstation, create an empty file by entering the touch filename command, where filename is the name of the file you will use when uploading the image to the server.

•If you are overwriting an existing file (including an empty file, if you had to create one), ensure that the permissions on the file are set correctly. Permissions on the file should be world-write.

Uploading Software Images to a TFTP Server

Use this procedure to upload a software image on a switch to a TFTP server for storage:

Step 1 Log into the switch through the console port or a Telnet session.

Step 2 Upload the software image to the TFTP server using the command appropriate for your switch and supervisor engine:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—Use the copy flash tftp command. When prompted, specify the TFTP server address and destination filename. On platforms that support the Flash file systems, you are first prompted for the Flash device and source filename, If desired, you can use the copy file-id tftp command on these platforms.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—Use the upload host filename [mod_num] command. Specify the number of the module from which to upload the image in the mod_num argument. You do not need to specify the module number if you are uploading the supervisor engine software image.

The software image is uploaded to the TFTP server.

This example shows how to upload the supervisor engine software image on a Catalyst 5000 family Supervisor Engine III to a TFTP server: 

Console> (enable) copy flash tftp

Flash device [bootflash]? slot0:

Name of file to copy from []? cat5000-sup3.5-1-1.bin

IP address or name of remote host [172.20.52.3]? 172.20.52.10

Name of file to copy to [cat5000-sup3.5-1-1.bin]? 

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC|

File has been copied successfully.

Console> (enable)

This example shows how to upload the supervisor engine software image on a Catalyst 5000 family Supervisor Engine II to a TFTP server: 

Console> (enable) upload 172.20.52.3 cat5000-sup.4-2-1.bin

Upload Module 1 image to cat5000-sup.4-2-1.bin on 172.20.52.3 (y/n) [n]? y

-

Finished network upload.  (3021332 bytes)

Console> (enable)

Downloading System Software Images to the Switch Using rcp

These sections describe how to download system software images to the switch supervisor engine and to intelligent modules using rcp:

•Understanding How rcp Software Image Downloads Work

•Preparing to Download an Image Using rcp

•Downloading Supervisor Engine Images Using rcp

•Downloading Switching Module Images Using rcp

•Example rcp Download Procedures

Understanding How rcp Software Image Downloads Work

You can download system software images to the switch using the remote copy protocol (rcp); rcp allows you to download system image files over the network from an rcp server.

Some modules, such as Catalyst 5000 family FDDI and ATM modules, have their own onboard Flash. When you download a software image file, the switch checks the header of the image file to determine the type of software image.

Depending on the type of software image you are downloading, one of the following occurs:

•Supervisor engine software image—The image file is downloaded to the supervisor engine Flash memory. On the Catalyst 5000 family Supervisor Engine II, II G, and III G, you can store only a single image file at a time. On the Catalyst 5000 family Supervisor Engine III and III F, and on the Catalyst 4000 family, 2926G series, 2948G, and 2980G switches, you can store multiple image files on the Flash memory system devices (such as boot Flash and, on the Supervisor Engine III and Catalyst 2926G series switches, Flash PC cards).

Caution Some supervisor engine software releases update the supervisor engine erasable programmable logic devices (EPLDs). The EPLDs can be updated only a limited number of times. You should avoid loading a new software release and then backing out unnecessarily. The supervisor engine software release notes indicate which software releases have code that updates the EPLDs.

•Intelligent module software images—If you specified a module number, the image file is downloaded to the specified module only (provided the image file is designed for the specified module type). If you do not specify a module number, the image file is downloaded to every module of the appropriate type. The file is relayed packet by packet to the appropriate modules using the Inter-Process Communications protocol internal to the system, with communication taking place across the switching bus. Downloading a software image to multiple modules significantly speeds up the process of updating the software on multiple modules of the same type.

Note For more information on working with system software image files on the Flash file system, refer to "Using the Flash File System."

Preparing to Download an Image Using rcp

Before you begin downloading a software image using rcp, make sure of the following:

•Ensure that the workstation acting as the rcp server supports the remote shell (rsh).

•Ensure that the switch has a route to the rcp server. The switch and the rcp server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the rcp server using the ping command.

•If you are accessing the switch through the console or a Telnet session without a valid username, make sure that the current rcp username is the one you want to use for the rcp download. You can enter the show users command to view the current valid username. If you do not want to use the current username, create a new rcp username using the set rcp username command. The new username will be stored in NVRAM. If you are accessing the switch through a Telnet session with a valid username, this username will be used and there is no need to set the rcp username.

•A power interruption (or other problem) during the download procedure can corrupt the Flash code. If the Flash code is corrupted, you can connect to the switch through the console port. On the Catalyst 5000 family Supervisor Engine II, II G, and III G, and on the Catalyst 4000 family, 2948G, and 2980G switches, you can download the Flash code again through an enabled port in VLAN 1. By default, port 1/1 is enabled. You can use port 1/1 or enable another port. On the Catalyst 5000 family Supervisor Engine III and the Catalyst 2926G series switches, you can boot from an uncorrupted system image on a Flash PC card.

Downloading Supervisor Engine Images Using rcp

Note Catalyst 5500 series only—If you have a redundant supervisor engine, you cannot download a system image directly from an rcp server to the Flash memory on the standby supervisor engine. When you download the image to the active supervisor engine, the standby supervisor engine synchronizes automatically with the new image. In addition, you cannot copy an image from the standby supervisor engine to the active supervisor engine.

Use the following procedure to download a supervisor engine software image to the switch from an
rcp server:

Step 1 Copy the software image file to the appropriate rcp directory on the workstation.

Step 2 Log into the switch through the console port or through a Telnet session. If you log in using Telnet, your Telnet session disconnects when you reset the switch to run the new software.

Step 3 Use the command appropriate for your switch and supervisor engine to download the software image from the rcp server:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—Use the copy rcp flash command. When prompted, enter the IP address or host name of the rcp server and the name of the file to download. On those platforms that support the Flash file system, you are also prompted for the Flash device to which to copy the file and the destination filename.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—Use the download host file [rcp] command, where host is the IP address or host name of the workstation acting as the rcp server and file is the name of the file to download.

Note The Supervisor Engine III F and the Catalyst 4000 family, 2948G, and 2980G switches have only one Flash device (bootflash:).

The switch downloads the image file from the rcp server:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—The image is copied to the specified Flash device.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—The Flash memory on the supervisor engine is erased and reprogrammed with the downloaded Flash code.

Note The switch remains operational while the image downloads.

Step 4 Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000, 2926G series, 2948G, and 2980G switches—Modify the BOOT environment variable using the set boot system flash device:filename prepend command, so that the new image boots when you reset the switch. Specify the Flash device (device:) and the filename of the downloaded image (filename).

Note This step is not necessary on the Catalyst 5000 family Supervisor Engine II, II G, and III G.

Step 5 Reset the switch using the reset system command. If you are connected to the switch through Telnet, your Telnet session disconnects.

During startup, on the Catalyst 5000 family Supervisor Engine III and III F, and on the Catalyst 4000 family, 2926G series, 2948G, and 2980G switches, the Flash memory on the supervisor engine is reprogrammed with the new Flash code.

Step 6 When the switch reboots, enter the show version command to check the version of the code on the switch.

Downloading Switching Module Images Using rcp

Use this procedure to download a software image to an intelligent module on a Catalyst 5000 family switch:

Step 1 Copy the software image file to the appropriate rcp directory on the workstation.

Step 2 Log into the switch through the console port or a Telnet session. If you log in using Telnet, your Telnet session might disconnect when you reset modules to run the new software.

Step 3 Use the command appropriate for your switch and supervisor engine to download the software image from the rcp server:

•Catalyst 5000 family Supervisor Engine III and III F

–If there is only one module of the type appropriate for the image, or if there are multiple modules of the same type and you want to update the image on all of them, use the copy rcp flash command. When prompted, enter the IP address or host name of the rcp server, the name of the file to download, the Flash device to which to copy the file, and the destination filename.

–If there are multiple modules of the type appropriate for the image but you only want to update a single module, use the copy rcp | m/bootflash: command, where m is the number of the module to which to download the software image. If you do not specify the module, all modules of the same type will be updated.

•Catalyst 5000 family Supervisor Engine II, II G, and III G

–If there is only one module of the type appropriate for the image, or if there are multiple modules of the same type and you want to update the image on all of them, use the download host file [rcp] command, where host is the IP address or host name of the rcp server and file is the name of the file to download.

–If there are multiple modules of the type appropriate for the image but you only want to update a single module, use the download host file mod_num command, where mod_num is the slot in which the module is installed. If you do not specify the module, all modules of the same type will be updated.

Note If you do not specify a module number, the switch examines the header of the image file to determine to which modules the software is downloaded. The image is then downloaded to all the modules of that type.

The switch downloads the image file, erases the Flash memory on the appropriate modules, and reprograms the Flash memory with the downloaded Flash code.

Note All modules in the switch remain operational while the image downloads.

Step 4 Reset the appropriate modules using the reset mod_num command. If you are connected through Telnet, your Telnet session disconnects if you reset the module through which your connection was made.

Step 5 When the upgraded modules come online, enter the show version [mod_num] command to check the version of the code on the switch.

Note For examples that show complete procedures for rcp downloads to intelligent modules, see the "Example Single Intelligent Module Image rcp Download (Catalyst 5000 Family Supervisor II, II G, or III G)" section, the "Example Multiple Module Image rcp Download (Supervisor II, II G, or III G)" section, the "Example Single Module Image rcp Download (Supervisor III or III F)" section, and the "Example Multiple Module Image rcp Download (Supervisor III or III F)" section.

Example rcp Download Procedures

These sections show example rcp download procedures:

•Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

•Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

•Example Single Module Image rcp Download (Supervisor III or III F)

•Example Single Intelligent Module Image rcp Download (Catalyst 5000 Family Supervisor II, II G, or III G)

•Example Multiple Module Image rcp Download (Supervisor III or III F)

•Example Multiple Module Image rcp Download (Supervisor II, II G, or III G)

Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor III or III F, or Catalyst 4000 Family, 2926G Series, 2948G, or 2980G Switches)

Note For a step-by-step procedure for downloading a supervisor engine software image from an rcp server, see the "Downloading Supervisor Engine Images Using rcp" section.

This example shows a complete rcp download procedure of a supervisor engine software image to a Catalyst 5000 family switch with a Supervisor Engine III or III F module, or to a Catalyst 4000 family, 2926G series, 2948G, or 2980G switch: 

Console> (enable) show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5530   007451586 Hw : 1.3

                              Fw : 3.1.2

                              Fw1: 3.1(2)

                              Sw : 4.1(2)

Console> (enable) copy rcp flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-sup3.4-2-1.bin

Flash device [bootflash]?

Name of file to copy to [cat5000-sup3.4-2-1.bin]?

4369664 bytes available on device bootflash, proceed (y/n) [n]? y

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCC

File has been copied successfully.

Console> (enable) set boot system flash bootflash:cat5000-sup3.4-2-1.bin prepend

BOOT variable = bootflash:cat5000-sup3.4-2-1.bin,1;bootflash:cat5000-sup3.4-1

-2.bin,1;

Console> (enable) reset system

This command will reset the system.

Do you want to continue (y/n) [n]? y

Console> (enable) 07/21/1998,13:51:39:SYS-5:System reset from Console//

System Bootstrap, Version 3.1(2)

Copyright (c) 1994-1997 by cisco Systems, Inc.

Presto processor with 32768 Kbytes of main memory

Autoboot executing command: "boot bootflash:cat5000-sup3.4-2-1.bin"

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCC

Uncompressing file:  ###########################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

################################################################################

#############

System Power On Diagnostics

NVRAM Size .. .................512KB

ID Prom Test ..................Passed

DPRAM Size ....................16KB

DPRAM Data 0x55 Test ..........Passed

DPRAM Data 0xaa Test ..........Passed

DPRAM Address Test ............Passed

Clearing DPRAM ................Done

System DRAM Memory Size .......32MB

DRAM Data 0x55 Test ...........Passed

DRAM Data 0xaa Test ...........Passed

DRAM Address Test  ............Passed

Clearing DRAM .................Done

EARL++ ........................Present

EARL RAM Test .................Passed

EARL Serial Prom Test .........Passed

Level2 Cache ..................Present

Level2 Cache test..............Passed

Boot image: bootflash:cat5000-sup3.4-2-1.bin

Downloading epld sram device please wait ...

Programming successful for Altera 10K10 SRAM EPLD

Downloading epld sram device please wait ...

Programming successful for Altera 10K30 SRAM EPLD

Downloading epld sram device please wait ...

Cisco Systems Console

Enter password:

07/21/1998,13:52:51:SYS-5:Module 1 is online

07/21/1998,13:53:11:SYS-5:Module 4 is online

07/21/1998,13:53:11:SYS-5:Module 5 is online

07/21/1998,13:53:14:PAGP-5:Port 1/1 joined bridge port 1/1.

07/21/1998,13:53:14:PAGP-5:Port 1/2 joined bridge port 1/2.

07/21/1998,13:53:40:SYS-5:Module 2 is online

07/21/1998,13:53:45:SYS-5:Module 3 is online

Console> show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5530   007451586 Hw : 1.3

                              Fw : 3.1.2

                              Fw1: 3.1(2)

                              Sw : 4.2(1)

Console>

Example Supervisor Image rcp Download (Catalyst 5000 Family Supervisor Engine II, II G, or III G)

Note For a step-by-step procedure for downloading a supervisor engine software image from an rcp server, see the "Downloading Supervisor Engine Images Using rcp" section.

This example shows a complete rcp download procedure of a supervisor engine software image to a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5509   007486003 Hw : 2.3

                              Fw : 3.1(2)

                              Fw1: 3.1(1)

                              Sw : 4.1(2)

Console> (enable) download 172.20.52.3 cat5000-sup.4-2-1.bin rcp

Download image cat5000-sup.4-2-1.bin from 172.20.52.3 to module 1 FLASH (y/n)

 [n]? y

/

Finished network single module download. (2748504 bytes)

FLASH on Catalyst:

Type            Address             Location

Intel 28F016    20000000            NMP (P3) 8MB SIM

Erasing flash sector...done.

Programming flash sector...done.

Erasing flash sector...done.

Programming flash sector...done.

Erasing flash sector...done.

Programming flash sector...done.

The system needs to be reset to run the new image.

Console> (enable) reset system

This command will reset the system.

Do you want to continue (y/n) [n]? y

Console> (enable) 07/21/1998,10:52:36:SYS-5:System reset from Console//

ATE0

ATS0=1

ROM Power Up Diagnostics of Feb 19 1998

Init NVRAM Log

LED Test  ................... done

ROM Checksum  ............... passed

Dual Port RAM r/w Test  ..... passed

ID PROM  .................... passed

System DRAM Size(mb)  ....... 16

DRAM Data Bus Test  ......... passed

DRAM Address Test  .......... passed

DRAM Byte/Word Access Test .. passed

EARL Test  .................. passed

BOOTROM Version 3.1(2), Dated Feb 19 1998 11:05:50

BOOT date: 07/21/98 BOOT time: 10:52:51

Uncompressing NMP image.  This will take a minute...

Downloading epld sram device please wait ...

Programming successful for Altera 10K10 SRAM EPLD

Updating epld flash version from 0000 to 0400

Running System Diagnostics from this Supervisor (Module 1)

This may take up to 2 minutes....please wait

Cisco Systems Console

Enter password:

07/21/1998,10:53:39:SYS-5:Module 1 is online

07/21/1998,10:53:58:PAGP-5:Port 1/1 joined bridge port 1/1.

07/21/1998,10:54:15:SYS-5:Module 7 is online

07/21/1998,10:54:22:SYS-5:Module 2 is online

07/21/1998,10:54:39:SYS-5:Module 9 is online

07/21/1998,10:54:43:SYS-5:Module 5 is online

07/21/1998,10:54:56:SYS-5:Module 3 is online

07/21/1998,10:54:57:SYS-5:Module 6 is online

07/21/1998,10:54:58:DTP-5:Port 3/1-2 has become dot10 trunk

07/21/1998,10:55:36:SYS-5:Module 2 is online


Console> show version 1

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

1   2    WS-X5509   007486003 Hw : 2.3

                              Fw : 3.1(2)

                              Fw1: 3.1(1)

                              Sw : 4.2(1)

Console>

Example Single Module Image rcp Download (Supervisor III or III F)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine III or III F, refer to the "Downloading Switching Module Images Using rcp" section.

This example shows a complete rcp download procedure of an ATM software image to a single ATM module in a Catalyst 5000 family switch with a Supervisor Engine III or III F module: 

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) copy rcp 4/flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-atm.3-2-7.bin

Download image rcp:cat5000-atm.3-2-7.bin to Module 4 FLASH (y/n) [n]? y

This command will reset Download Module(s) you selected.

Do you wish to continue download flash (y/n) [n]? y

-

Download done for module 4, please wait for it to come online

File has been copied successfully.

Console> (enable) 07/21/1998,13:13:54:SYS-5:Module 4 is online

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Example Single Intelligent Module Image rcp Download (Catalyst 5000 Family Supervisor II, II G,
or III G)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G, refer to the "Downloading Switching Module Images Using rcp" section.

This example shows a complete rcp download procedure of an FDDI software image to a single FDDI module in a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 3

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

3   2    WS-X5101   003489788 Hw : 1.0

                              Fw : 1.1

                              Fw1: 1.3

                              Sw : 2.1(7)

Console> (enable) download 172.20.52.3 cat5000-fddi.3-1-1.bin 3 rcp

This command will reset module 3.

Download image cat5000-fddi.3-1-1.bin from 172.20.52.3 to Module 3 FLASH (y/n) [

n]? y

|

Finished network single module download. (1060456 bytes)

...............................................................................

...............................................................................

...............................................................................

...............................................................................

...............................................................................

..................................

SCP download checksum ok

SCP download done.

Please wait until module 3 comes online before resetting.

(Approximately 5 minutes)

Console> (enable) 07/21/1998,11:23:36:SYS-5:Module 3 FLASH pro

gramming complete

07/21/1998,11:24:59:SYS-5:Module 3 is online

07/21/1998,11:25:00:DTP-5:Port 3/1-2 has become dot10 trunk

Console> (enable) show version 3

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

3   2    WS-X5101   003489788 Hw : 1.0

                              Fw : 1.1

                              Fw1: 1.3

                              Sw : 3.1(1)

Console> (enable)

Example Multiple Module Image rcp Download (Supervisor III or III F)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine III or III F, refer to the "Downloading Switching Module Images Using TFTP" section.

This example shows a complete rcp download procedure of an ATM software image to multiple ATM modules in a Catalyst 5000 family switch with a Supervisor Engine III or III F module: 

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) show version 5

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

5   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) copy rcp flash

IP address or name of remote host []? 172.20.52.3

Name of file to copy from []? cat5000-atm.3-2-7.bin

Download image rcp:cat5000-atm.3-2-7.bin to Module 4 FLASH (y/n) [n]? y

Download image rcp:cat5000-atm.3-2-7.bin to Module 5 FLASH (y/n) [n]? y

This command will reset Download Module(s) you selected.

Do you wish to continue download flash (y/n) [n]? y

-

Download done for module 4, please wait for it to come online

Download done for module 5, please wait for it to come online

File has been copied successfully.

Console> (enable) 07/21/1998,12:25:10:SYS-5:Module 4 is online

07/21/1998,12:25:10:SYS-5:Module 5 is online

Console> (enable) show version 4

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

4   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable) show version 5

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

5   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Example Multiple Module Image rcp Download (Supervisor II, II G, or III G)

Note For a step-by-step procedure for downloading software images to intelligent modules on a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G, refer to the "Downloading Switching Module Images Using rcp" section.

This example shows a complete rcp download procedure of an ATM software image to multiple ATM modules in a Catalyst 5000 family switch with a Supervisor Engine II, II G, or III G module: 

Console> (enable) show version 8

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

8   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(4)

Console> (enable) show version 9

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

9   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(6)

Console> (enable) download 172.20.52.3 cat5000-atm.3-2-7.bin rcp

Download image cat5000-atm.3-2-7.bin from 172.20.52.3 to Module 8 FLASH (y/n) [n

]? y

Download image cat5000-atm.3-2-7.bin from 172.20.52.3 to Module 9 FLASH (y/n) [n

]? y

This command will reset download module(s) you selected.

Do you wish to continue download to flash (y/n) [n]? y

-

Download done for module 8, please wait for it to come online

Download done for module 9, please wait for it to come online

Finished network multiple modules download. (2378316 bytes)

Please wait until module(s) come online before resetting.

Console> (enable) 07/21/1998,13:19:54:SYS-5:Module 8 is online

07/21/1998,13:19:54:SYS-5:Module 9 is online

Console> (enable) show version 8

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

8   1    WS-X5155   003414855 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable) show version 9

Mod Port Model      Serial #  Versions

--- ---- ---------- --------- ----------------------------------------

9   1    WS-X5155   003414463 Hw : 1.2

                              Fw : 1.3

                              Fw1: 1.3

                              Sw : 3.2(7)

Console> (enable)

Uploading System Software Images to an rcp Server

These sections describe how to upload system software images from a switch to an rcp server:

•Preparing to Upload an Image to an rcp Server

•Uploading Software Images to an rcp Server

Note For more information on working with system software image files on the Flash file system, see "Using the Flash File System."

Preparing to Upload an Image to an rcp Server

Before you attempt to upload a software image to an rcp server, do the following:

•Ensure that the workstation acting as the rcp server is configured properly.

•Ensure that the switch has a route to the rcp server. The switch and the rcp server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the rcp server using the ping command.

•If you are overwriting an existing file (including an empty file, if you had to create one), ensure that the permissions on the file are set correctly. Permissions on the file should be write for the specific username.

Uploading Software Images to an rcp Server

Use this procedure to upload a software image on a switch to an rcp server for storage:

Step 1 Log into the switch through the console port or a Telnet session.

Step 2 Upload the software image to the rcp server using the command appropriate for your switch and supervisor engine:

•Catalyst 5000 family Supervisor Engine III and III F, and Catalyst 4000 family, 2926G series, 2948G, and 2980G switches—Use the copy flash rcp command. When prompted, specify the rcp server address, and destination filename. On platforms that support the Flash file systems, you are first prompted for the Flash device and source filename, If desired, you can use the copy file-id rcp command on these platforms.

•Catalyst 5000 family Supervisor Engine II, II G, and III G—Use the upload host filename [mod_num] rcp command. Specify the number of the module from which to upload the image in the mod_num argument. You do not need to specify the module number if you are uploading the supervisor engine software image.

The software image is uploaded to the rcp server.

This example shows how to upload the supervisor engine software image on a Catalyst 5000 family Supervisor Engine III to an rcp server: 

Console> (enable) copy flash rcp

Flash device [bootflash]? slot0:

Name of file to copy from []? cat5000-sup3.5-1-1.bin

IP address or name of remote host [172.20.52.3]? 172.20.52.10

Name of file to copy to [cat5000-sup3.5-1-1.bin]? 

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC|


File has been copied successfully.

Console> (enable)

This example shows how to upload the supervisor engine software image on a Catalyst 5000 family Supervisor Engine II to an rcp server: 

Console> (enable) upload 172.20.52.3 cat5000-sup.4-2-1.bin rcp

Upload Module 1 image to cat5000-sup.4-2-1.bin on 172.20.52.3 (y/n)? y

Finished network upload.  (3021332 bytes)

Console> (enable)

Downloading Software Images over a Serial Connection on the Console Port

These sections describe how to perform a serial download of software images over the supervisor engine console port using Kermit, a common file-transfer and terminal-emulation software program:

•Preparing to Download an Image Using Kermit

•Downloading Software Images Using Kermit (PC Procedure)

•Downloading Software Images Using Kermit (UNIX Procedure)

•Example Serial Software Image Download Procedures

Preparing to Download an Image Using Kermit

Before you begin a serial download of a software image using Kermit, make sure of the following:

•On a UNIX workstation, make sure your shell window is local (not an rlogin window to a different workstation).

•Ensure that the supervisor engine console port is connected to a serial port on your PC or workstation with a serial cable.

•Ensure that the Kermit software is installed on your PC or workstation.

•Ensure that the line speed settings are the same on the PC or workstation and on the switch:

–On the switch, you can change the console port speed by entering the set system baud rate command. The default baud rate is 9600 baud.

–On the PC or workstation, you can change the baud rate of the serial port by entering the set speed rate command at the Kermit> prompt.

Caution To prevent communication problems, do not use a speed greater than 19,200 baud.

•Ensure that Kermit is using the proper serial port.

–On a PC, specify the serial port using the set port comx command, where x is the PC serial port number (1 through 8) that you connected to the switch.

–On a UNIX workstation, specify the serial port using the set port /dev/ttyx command, where x is the serial port (a or b) that you connected to the switch.

Downloading Software Images Using Kermit (PC Procedure)

Note This procedure applies to PC serial downloads only. For information on performing a serial download on a UNIX workstation, refer to the "Downloading Software Images Using Kermit (UNIX Procedure)" section.

Use this procedure to perform a serial download of a software image over the supervisor engine
console port:

Step 1 Copy the software image file to the directory where Kermit is loaded.

Step 2 Start Kermit on the PC.

Note Before continuing, ensure that the line speed is correct and that you have selected the proper serial line, as described in the "Preparing to Download an Image Using Kermit" section.

Step 3 At the Kermit> prompt, enter the connect command to connect to the switch. If your line and speed are set correctly, the switch Console> prompt appears.

Step 4 Enter the enable command to enter privileged mode.

Step 5 Enter the download serial command. The file is downloaded to module 1 by default.

Step 6 When prompted, confirm the download.

Step 7 Enter the escape sequence Ctrl-]-c by holding down the Ctrl key while you press ], and then press c.

Step 8 At the Kermit> prompt, enter the send filename command to send the file to the switch.

The switch downloads the image file, erases the Flash memory on the supervisor engine or the appropriate module, and reprograms the Flash memory with the downloaded Flash code.

Note The switch remains operational while the image downloads.

Step 9 When the Kermit> prompt reappears, enter the connect command to return to the switch Console> prompt. You will see status information as the switch erases and reprograms the Flash memory.

Note If you enter the connect command more than two minutes after the Kermit> prompt reappears, you might see only a Console> prompt instead of the status information about erasing and programming Flash code.

Step 10 Reset the switch using the reset system command.

Step 11 When the switch reboots, enter the show version [mod_num] command to check the version of the code on the switch.

Note For an example that shows a complete serial download procedure using Kermit on a PC, see the "Example PC Serial Download Procedure" section.

Downloading Software Images Using Kermit (UNIX Procedure)

Note This procedure applies to UNIX serial downloads only. For information on performing a serial download on a PC, refer to the "Downloading Software Images Using Kermit (PC Procedure)" section.

Use this procedure to perform a serial download of a software image over the supervisor engine
console port.

To copy the software to the workstation, log in as root, and perform these steps:

Step 1 Copy the software image file to your home directory.

Step 2 At the UNIX command prompt, start Kermit by entering the kermit command (make sure the directory where Kermit is installed is included in the $PATH environment variable on the workstation).

Note Before continuing, ensure that the line speed is correct and that you have selected the proper serial line, as described in the "Preparing to Download an Image Using Kermit" section.

Step 3 At the C-Kermit> prompt, enter the connect command to connect to the switch. If your line and speed are set correctly, the switch Console> prompt appears.

Step 4 Enter the enable command to enter privileged mode.

Step 5 Enter the download serial command. The file downloads to module 1 by default.

Step 6 When prompted, confirm the download.

Step 7 Enter the escape sequence Ctrl-\-c by holding down the Ctrl key while you press \, and then press c.

Step 8 At the Kermit> prompt, enter the send filename command to send the file to the switch.

You can monitor the progress of the download by pressing the a key at any time during the Kermit download. A dot appears onscreen for every four packets transferred. If there is a problem transferring the file, one or more of the following letter codes appear:

•T—Kermit timed out.

•N—Kermit is not acknowledging the switch download process.

•E—Kermit detected an error in the progress of the transaction.

The switch downloads the image file, erases the Flash memory on the supervisor engine or the appropriate module, and reprograms the Flash memory with the downloaded Flash code.

Note The switch remains operational while the image downloads.

Step 9 Press Return to return to the C-Kermit> prompt. When the Kermit> prompt reappears, enter the connect command to return to the switch Console> prompt. You will see status information as the switch erases and reprograms the Flash memory.

Note If you enter the connect command more than two minutes after the Kermit> prompt reappears, you might see only a Console> prompt instead of the status information about erasing and programming Flash code.

Step 10 Reset the switch using the reset system command.

Step 11 When the switch reboots, enter the show version [mod_num] command to check the version of the code on the switch.

Note For an example that shows a complete serial download procedure using Kermit on a
UNIX workstation, see the "Example UNIX Workstation Serial Download Procedure" section.

Example Serial Software Image Download Procedures

These sections show example serial download procedures over the supervisor engine console port using Kermit:

•Example PC Serial Download Procedure

•Example UNIX Workstation Serial Download Procedure

Example PC Serial Download Procedure

This screen output shows an example of a complete serial download procedure on a PC: 

C:\ copy A:\*.*

copying c5009_xx.bin

C:\ kermit

Kermit, 4C(057) 06 Apr 98, 4.2 BSD

Type ? for help

Kermit> set port com1

Kermit> set speed 9600

Kermit> connect

Connecting to com1,speed 9600.

The escape character is ^] (ASCII 29).

Type the escape character followed by C to get back,

or followed by ? to see other options

Console> enable

Console> (enable) download serial

Download CBI image via console port (y/n) [n]? y


Waiting for DOWNLOAD!

Return to your local Machine by typing its escape sequence

Issue Kermit send command from there[ Send `Filename`]


<CONTROL-] c to return to Local Machine>


Kermit> send c5009_xx.bin



          File name: c5009_xx.bin

 KBytes transferred: xxxx

Percent transferred: 100%

            Sending: Complete


  Number of Packets: xxxx

  Number of retries: None

         Last error: None

       Last warning: None

Kermit> connect



Finished network download.  (1136844 bytes)

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

Flash erase in progress ... Erase done

Programming Flash:  Flash Programming Complete

The system needs to be reset to run the new image.


Cisco Systems Console 
Enter password: 
Mon Apr 06, 1998, 14:35:08 
Console>

Example UNIX Workstation Serial Download Procedure

This screen output shows an example of a complete serial download procedure on a UNIX workstation: 

workstation% cd /tmp

workstation% tar -xvfp /dev/rfd0

c5009_xx.bin, 1156046 bytes, 2258 tape blocks

workstation% ls -la

total 1150

drwxrwsrwt  5 bin           512 Sep 28 04:15 .

drwxr-xr-x 18 root         1536 Sep 27 15:41 ..

-r--r--r--  1 60000     1156046 Jul 18 10:32 c5009_xx.bin

workstation% kermit

C-Kermit, 4E(072) 06 Apr 98, SUNOS 4.x

Type ? for help

C-Kermit> set line /dev/ttya

C-Kermit> set speed 9600

/dev/ttya: 9600 baud

C-Kermit> connect

Connecting thru /dev/ttya, speed 9600.

The escape character is CTRL-\ (28).


Type the escape character followed by C to get back,

or followed by ? to see other options.


Console> enable

Console> (enable) download serial c5009_xx.bin


Download CBI image via console port (y/n) [n]? y


Waiting for DOWNLOAD!

Return to your local Machine by typing its escape sequence

Issue Kermit send command from there[ Send `Filename`]

[Back at Local System]

C-Kermit> send c5009_xx.bin

SF

c5009_xx.bin => c5009_xx.bin, Size: 1156046


CTRL-F to cancel file,  CTRL-R to resend current packet

CTRL-B to cancel batch, CTRL-A for status report: 
.........................................................................................
.....................................

*** Display Truncated ***

...............................................................

.................................... [OK]

ZB?

C-Kermit> connect

Connecting thru /dev/ttya, speed 9600.

The escape character is CTRL-\ (28).

Type the escape character followed by C to get back,

or followed by ? to see other options.


Download OK

Initializing Flash

Programming Flash

Base....Code....Length....Time....Done


Cisco Systems Console

Enter password:

Mon Apr 06, 1998, 17:35:08

Console>