Table Of Contents

Configuring VLANs

Configuring VLAN Trunking Protocol

Configure the Switch as a VTP Server

Configure the Switch as a VTP Client

Configure the Switch as VTP Transparent

Configuring VLANs

Create VLANs

Assign Switch Ports to VLANs

Configuring VLANs

---

To configure VLANs on the switch, perform these tasks:

---

Step 1 Configuring VLAN Trunking Protocol—Create a VLAN Trunking Protocol (VTP) domain and set the VTP mode on the switch.

Step 2 Configuring VLANs—Create VLANs in the VTP domain and assign switch ports to those VLANs.

---

Configuring VLAN Trunking Protocol

VTP propagates information about the VLAN configuration throughout the switched network.

---

Note VTP only exchanges VLAN information over VLAN trunk links. For information on configuring trunk links, see "Configuring EtherChannel and VLAN Trunks."

---

The switch can operate in any one of these three VTP modes:

•Server—VTP servers advertise their VLAN configuration to other switches in the same VTP domain and synchronize their VLAN configuration with other switches based on advertisements received over trunk links. The VTP server is the default mode.

•Client—VTP clients are similar to VTP servers, except that you cannot create, change, or delete VLANs on a VTP client.

•Transparent—VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements.

---

Note Before you configure VLANs on the switch, you should decide whether to use VTP. If you decide to use VTP, you need to decide whether the switch should function as a VTP client or a VTP server. If you are connecting the switch to an existing network, make sure that your VTP configuration is compatible with the rest of the network.

---

Configure the Switch as a VTP Server

When you configure a switch as a VTP server, you must define a VTP domain before you can create VLANs.

To configure a switch as a VTP server, perform this task in privileged mode:

	Task	Command
Step 1	Assign a name to the VTP management domain.	set vtp domain name
Step 2	Set the VTP mode.	set vtp mode server
Step 3	Verify the VTP configuration.	show vtp domain

This example shows how to configure a switch as a VTP server:

Console> (enable) set vtp domain BigCorp

VTP domain BigCorp modified

Console> (enable) set vtp mode server

VTP domain BigCorp modified

Console> (enable) show vtp domain

Domain Name                      Domain Index VTP Version Local Mode  Password

-------------------------------- ------------ ----------- ----------- ----------

BigCorp                          1            2           server      -

Vlan-count Max-vlan-storage Config Revision Notifications

---------- ---------------- --------------- -------------

5          1023             0               disabled

Last Updater    V2 Mode  Pruning  PruneEligible on Vlans

--------------- -------- -------- -------------------------

0.0.0.0         disabled disabled 2-1000

Console> (enable)

Configure the Switch as a VTP Client

When you configure a switch as a VTP client, you cannot configure VLANs on the switch; instead, you configure VLANs on a VTP server in the same VTP domain as the client. The VTP client synchronizes its VLAN configuration to the configuration of the server.

To configure a switch as a VTP client, perform this task in privileged mode:

	Task	Command
Step 1	Assign a name to the VTP management domain.	set vtp domain name
Step 2	Set the VTP mode.	set vtp mode client
Step 3	Verify the VTP configuration. (It might take a few minutes before a VTP client learns the VTP and VLAN configuration information from neighboring switches.)	show vtp domain

This example shows how to configure a switch as a VTP client:

Console> (enable) set vtp domain BigCorp

VTP domain BigCorp modified

Console> (enable) set vtp mode client   

VTP domain BigCorp modified

Console> (enable) show vtp domain

Domain Name                      Domain Index VTP Version Local Mode  Password

-------------------------------- ------------ ----------- ----------- ----------

BigCorp                          1            2           client      -

Vlan-count Max-vlan-storage Config Revision Notifications

---------- ---------------- --------------- -------------

5          1023             0               disabled

Last Updater    V2 Mode  Pruning  PruneEligible on Vlans

--------------- -------- -------- -------------------------

0.0.0.0         disabled disabled 2-1000

Console> (enable)

Configure the Switch as VTP Transparent

When you configure a switch as VTP transparent, you must configure VLAN information manually on the switch. A VTP-transparent switch does not advertise its VLAN configuration information to other switches and will ignore VTP updates from VTP clients and servers.

To configure a switch for VTP transparent mode, perform this task in privileged mode:

	Task	Command
Step 1	Set the VTP mode.	set vtp mode transparent
Step 2	Verify the VTP configuration.	show vtp domain

This example shows how to configure a switch as VTP transparent:

Console> (enable) set vtp mode transparent

VTP domain  modified

Console> (enable) show vtp domain

Domain Name                      Domain Index VTP Version Local Mode  Password

-------------------------------- ------------ ----------- ----------- ----------

                                 1            2           Transparent -

Vlan-count Max-vlan-storage Config Revision Notifications

---------- ---------------- --------------- -------------

5          1023             0               disabled

Last Updater    V2 Mode  Pruning  PruneEligible on Vlans

--------------- -------- -------- -------------------------

0.0.0.0         disabled disabled 2-1000

Console> (enable)

Configuring VLANs

When you configure the switch for VTP, you can create, modify, and delete VLANs on the switch (unless you configured the switch as a VTP client). When you configure a VLAN on a VTP server, the configuration information is distributed to switches throughout the VTP domain.

VTP clients and servers in the same domain update their VLAN configuration based on the advertised configuration. VTP transparent switches do not act on VTP updates; you must manually make changes to the VLAN configuration on such switches.

Typically, in an IP network, each VLAN is associated with a single IP subnetwork. That is, all of the hosts in a given VLAN belong to a single subnet, use the same subnet mask, and use one or more default gateways that are connected to that subnetwork. Stations in different VLANs cannot communicate with one another without a router configured to route between the different VLANs.

The supervisor engine software supports many VLAN types. This section describes only how to configure Ethernet VLANs. For information about configuring other types of VLANs, refer to the Software Configuration Guide for your switch.

Create VLANs

To configure an Ethernet VLAN in a VTP domain, perform this task in privileged mode:

	Task	Command
Step 1	Create a VLAN by assigning it a VLAN number and, if desired, a VLAN name.	set vlan vlan_num [name name]
Step 2	Verify the VLAN configuration.	show vlan vlan_num

This example shows how to create a VLAN and verify the VLAN configuration:

Console> (enable) set vlan 10 name Corporate

Vlan 10 configuration successful

Console> (enable) show vlan 10

VLAN Name                             Status    IfIndex Mod/Ports, Vlans

---- -------------------------------- --------- ------- ------------------------

10   Corporate                        active    103     

VLAN Type  SAID       MTU   Parent RingNo BrdgNo Stp  BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ ------ ---- -------- ------ ------

10   enet  100010     1500  -      -      -      -    -        0      0

VLAN DynCreated

---- ----------

10   static    

VLAN AREHops STEHops Backup CRF 1q VLAN

---- ------- ------- ---------- -------

Console> (enable)

Assign Switch Ports to VLANs

After you create a VLAN, you can assign one or more switch ports to the VLAN. Devices that are connected to those ports will belong to that VLAN. Make sure that the connected device is properly configured with an IP address, subnet mask, and default gateway in the subnet that is associated with the VLAN.

To add a switch port to a VLAN, perform this task in privileged mode:

	Task	Command
Step 1	Add one or more switch ports to a VLAN.	set vlan vlan_num mod_num/port_num
Step 2	Verify that the ports are properly assigned to the VLAN.	show vlan vlan_num
Step 3	Check to which VLAN a particular port belongs.	show port [mod_num/port_num]

This example shows how to assign ports to a VLAN and verify to which VLAN the ports belong:

Console> (enable) set vlan 10 3/1-2

VLAN 10 modified.

VLAN 1 modified.

VLAN  Mod/Ports

---- -----------------------

10    3/1-2

Console> (enable) show vlan 10

VLAN Name                             Status    IfIndex Mod/Ports, Vlans

---- -------------------------------- --------- ------- ------------------------

10   Corporate                        active    103     3/1-2

<... output truncated ...>

Console> (enable) show port 3

Port  Name               Status     Vlan       Level  Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

 3/1                     connected  10         normal   full  1000 1000BaseSX

 3/2                     connected  10         normal   full  1000 1000BaseSX

<... output truncated ...>

Console> (enable)