-
Catalyst 4000 Family Command Reference, 7.3
-
Switch and ROM Monitor Commands
-
Index
-
Preface
-
Command-Line Interface
-
alias through copy
-
delete through session
-
set through set dot1x
-
set enablepass through set logging history
-
set logging level through set pvlan
-
set pvlan mapping through set spantree portinstancepri
-
set spantree portpri through set vtp pruning
-
show accounting through show counters
-
show crypto key through show multicast group
-
show multicast group count through show pvlan mapping
-
show qos info through show test
-
show time through write terminal
-
Acronyms
-
Table Of Contents
show crypto key
Use the show crypto key command to display RSA key pair information.
show crypto key
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display key pair information:
Console> (enable) show crypto keyRSA keys was generated at: Tue Dec 14 1999, 14:22:481024 37 1120518394839901301166714853840995094745037456682394891249441779951543727187159999 643683033910964386179342272044371326668692894898498425705315929789724607692104535472010393 868648783669579338660482094092720514951237657028608860832162809370173090068651870589350241 85402826063185974102411558894697025607154868421Console> (enable)Related Commands
clear crypto key rsa
set crypto key rsashow dot1q-all-tagged
Use the show dot1q-all-tagged command to display dot1q tagging status.
show dot1q-all-tagged
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to display dot1q tagging status:
Console> (enable) show dot1q-all-taggedDot1q all tagged mode disabledConsole> (enable)Related Commands
show dot1x
Use the show dot1x command to display the system dot1x capabilities, protocol version, and timer values.
show dot1x
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the dot1x information of the system:
Console> show dot1xPAE Capability Authenticator OnlyProtocol Version 1system-auth-control enabledre-authentication disabledmax-req 2quiet-period 60 secondsre-authperiod 3600 secondsserver-timeout 30 secondssupp-timeout 30 secondstx-period 30 secondsConsole>Related Commands
show dvlan statistics
Use the show dvlan statistics command to display DVLAN statistics.
show dvlan statistics
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the DVLAN statistical information:
Console> show dvlan statisticsVMPS Client Statistics----------------------VQP Queries: 0VQP Responses: 0Vmps Changes: 0VQP Shutdowns: 0VQP Denied: 0VQP Wrong Domain: 0VQP Wrong Version: 0VQP Insufficient Resource: 0Console>show environment
Use the show environment command to display system status information.
show environment {all | power}
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to display environmental status information:
Console> show environment allTotal Inline Power Available: 0 WattTotal Inline Power Drawn From the System: 0 WattRemaining Inline Power in the System: 0 WattDefault Inline Power allocation per port: 6.00 Watts (0.11 Amps @51V)Module Inline Power Allocated(mA)------ --------------------------1 02 03 0Console>Related Commands
set inlinepower defaultallocation
show environment power
Use the show environment power command to display the current power configuration for the switch, the total power available to the system, and amount of power currently in use.
show environment power
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the current power configuration for the switch.
Console> show environment powerTotal Inline Power Available:0 WattTotal Inline Power Drawn From the System:0 WattRemaining Inline Power in the System:0 WattDefault Inline Power allocation per port:6.00 Watts (0.11 Amps @51V)Module Inline Power Allocated(mA)------ --------------------------1 02 03 0Power Budget is :2 suppliesPower Available to the System (excluding voice power):750 Watts (62.06 Amps@12V)Power Drawn from the System (excluding voice power):265 Watts (22.01 Amps@12V)Remaining Power (excluding voice power):485 Watts (40.05 Amps @12V)Console>Related Commands
set power budget
show config
show systemshow errdisable-timeout
Use the show errdisable-timeout command to display the configuration and status of the errdisable timeout.
show errdisable-timeout
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
If your system is configured with a Supervisor Engine 2, a crossbar-fallback error may be displayed in the ErrDisable Reason field.
Examples
This example shows how to display the errdisable timeout configuration and status:
Console> (enable) show errdisable-timeoutErrDisable Reason Timeout Status------------------- ------------bpdu-guard Disablechannel-misconfig Disableduplex-mismatch Disableudld Enablecrossbar-fallback Disableother DisableInterval: 300 secondsPorts that will be enabled at the next timeout:Port Errdisable Reason Port ErrDisableTimeout Action on Timeout---- ----------------- ---------------------- -----------------3/3 udld Disable Remain Disabled3/4 udld Enable EnabledConsole>(enable)Related Commands
show errordetection
Use the show errordetection command to display error detection settings.
show errordetection
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Examples
This example shows how to display the error detection settings:
Console> (enable) show errordetectionInband error detection: disabledMemory error detection: enabledPort counter error detection: disabledConsole> (enable)Related Commands
show file
Use the show file command to display the contents of a file.
show file [device:] filename [dump]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
A colon (:) is required after the specified device.
Examples
This example shows how to view the file cfg2:
Console> (enable) show file cfg2begin!# ***** NON-DEFAULT CONFIGURATION *****!!# Wed Apr 21 1999, 22:55:10!#version 5.3(0.53-Eng)ASP!set prompt test>!#frame distribution methodset port channel all distribution mac both!#ipset interface sc0 1 172.20.25.145/255.255.0.0 172.20.255.255set ip route 0.0.0.0/0.0.0.0 172.20.25.201!#set boot commandset boot auto-config non-recurring!#qosset qos map 1q4t 0 0 cos 0set qos map 1q4t 0 0 cos 1set qos map 1q4t 0 0 cos 2set qos map 1q4t 0 0 cos 4set qos map 1q4t 0 0 cos 5set qos map 1q4t 0 0 cos 6set qos map 1q4t 0 0 cos 7set qos wred-threshold 1q4t tx queue 1 0 0 0 0!#module 1 : 4-port 10/100BaseTX Supervisor!#module 2 : 24-port 10BaseF Ethernet!#module 3 : 12-port 10/100BaseTX Ethernet!#module 4 empty!#module 5 emptyendConsole> (enable)show flash
Use the show flash command to list Flash information, including file code names, version numbers, and sizes.
show flash [[m/]device:] [all | chips | filesys]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
A colon (:) is required after the specified device.
Examples
The following examples show how to list Flash information:
Console> show flash-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name1 .D 2 2D6B310A 100fc0 15 1052123 Aug 26 1998 15:43:50 cat5k_r47_1.cbi2 .. 2 43B312DF 201ed8 15 1052608 Aug 27 1998 10:23:30 cat5k_r47_1.cbi6283877 bytes available (2104731 bytes used)Console> show flash chips******** Intel Series 2+ Status/Register Dump ********ATTRIBUTE MEMORY REGISTERS:Config Option Reg (4000): 2Config Status Reg (4002): 0Card Status Reg (4100): 1Write Protect Reg (4104): 4Voltage Cntrl Reg (410C): 0Rdy/Busy Mode Reg (4140): 2COMMON MEMORY REGISTERS: Bank 0Intelligent ID Code : 8989A0A0Compatible Status Reg: 8080Global Status Reg: B0B0Block Status Regs:0 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B08 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B016 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B024 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0COMMON MEMORY REGISTERS: Bank 1Intelligent ID Code : 8989A0A0Compatible Status Reg: 8080Global Status Reg: B0B0Block Status Regs:0 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B08 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B016 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B024 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0COMMON MEMORY REGISTERS: Bank 2Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedCOMMON MEMORY REGISTERS: Bank 3Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedCOMMON MEMORY REGISTERS: Bank 4Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedConsole> show flash filesys-------- F I L E S Y S T E M S T A T U S --------Device Number = 0DEVICE INFO BLOCK:Magic Number = 6887635 File System Vers = 10000 (1.0)Length = 800000 Sector Size = 20000Programming Algorithm = 4 Erased State = FFFFFFFFFile System Offset = 20000 Length = 7A0000MONLIB Offset = 100 Length = C730Bad Sector Map Offset = 1FFF8 Length = 8Squeeze Log Offset = 7C0000 Length = 20000Squeeze Buffer Offset = 7E0000 Length = 20000Num Spare Sectors = 0Spares:STATUS INFO:WritableNO File Open for WriteComplete StatsNo Unrecovered ErrorsUSAGE INFO:Bytes Used = 201D9B Bytes Available = 5FE265Bad Sectors = 0 Spared Sectors = 0OK Files = 1 Bytes = 100FC0Deleted Files = 1 Bytes = 100DDBFiles w/Errors = 0 Bytes = 0Console> show flash all-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name1 .D 2 2D6B310A 100fc0 15 1052123 Aug 26 1998 15:43:50 cat5k_r47_1.cbi2 .. 2 43B312DF 201ed8 15 1052608 Aug 27 1998 10:23:30 cat5k_r47_1.cbi6283877 bytes available (2104731 bytes used)-------- F I L E S Y S T E M S T A T U S --------Device Number = 0DEVICE INFO BLOCK:Magic Number = 6887635 File System Vers = 10000 (1.0)Length = 800000 Sector Size = 20000Programming Algorithm = 4 Erased State = FFFFFFFFFile System Offset = 20000 Length = 7A0000MONLIB Offset = 100 Length = C730Bad Sector Map Offset = 1FFF8 Length = 8Squeeze Log Offset = 7C0000 Length = 20000Squeeze Buffer Offset = 7E0000 Length = 20000Num Spare Sectors = 0Spares:STATUS INFO:WritableNO File Open for WriteComplete StatsNo Unrecovered ErrorsUSAGE INFO:Bytes Used = 201D9B Bytes Available = 5FE265Bad Sectors = 0 Spared Sectors = 0OK Files = 1 Bytes = 100FC0Deleted Files = 1 Bytes = 100DDBFiles w/Errors = 0 Bytes = 0******** Intel Series 2+ Status/Register Dump ********ATTRIBUTE MEMORY REGISTERS:Config Option Reg (4000): 2Config Status Reg (4002): 0Card Status Reg (4100): 1Write Protect Reg (4104): 4Voltage Cntrl Reg (410C): 0Rdy/Busy Mode Reg (4140): 2COMMON MEMORY REGISTERS: Bank 0Intelligent ID Code : 8989A0A0Compatible Status Reg: 8080Global Status Reg: B0B0Block Status Regs:0 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B08 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B016 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B024 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0COMMON MEMORY REGISTERS: Bank 1Intelligent ID Code : 8989A0A0Compatible Status Reg: 8080Global Status Reg: B0B0Block Status Regs:0 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B08 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B016 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B024 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0COMMON MEMORY REGISTERS: Bank 2Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedCOMMON MEMORY REGISTERS: Bank 3Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedCOMMON MEMORY REGISTERS: Bank 4Intelligent ID Code : FF00FFIID Not Intel -- assuming bank not populatedRelated Commands
reset—switch
show version—switchshow garp timer
Use the show garp timer command to display all the values of the GARP timers.
show garp timer
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
You must maintain the following relationship for the various timer values:
•
Leave time must be greater than or equal to three times the join time.
•
Caution
Note
Examples
This example shows how to display all the values of the GARP timers:
Console> (enable) show garp timerTimer Timer Value (milliseconds)-------- --------------------------Join 200Leave 600LeaveAll 10000Console> (enable)Related Commands
set garp timer
set gmrp timer
set gvrp timershow gmrp configuration
Use the show gmrp configuration command to display complete GMRP-related configuration information.
show gmrp configuration
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If the port list exceeds the line spaces available, the list wraps to the next line.
Examples
This example shows the display when GMRP is enabled:
Console> (enable) show gmrp configurationGlobal GMRP Configuration:GMRP Feature is currently enabled on this switch.GMRP Timers (milliseconds):Join = 200Leave = 600LeaveAll = 10000Port based GMRP Configuration:GMRP Status Registration Forward All Port--------------------------------------------------------------------Enabled Fixed Disabled 2/1,3/1-2Console> (enable)Related Commands
show gmrp statistics
Use the show gmrp statistics command to display GMRP-related statistics for a specified VLAN.
show gmrp statistics [vlan]
Syntax Description
Defaults
If no VLAN is specified, the default is that statistics for VLAN 1 are shown.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows the display for all the GMRP-related statistics for VLAN 23:
Console> show gmrp statistics 23GMRP Statistics for vlan <23>:Total valid GMRP Packets Received: 500Join Emptys: 200Join INs: 250Leaves: 10Leave Alls: 35Emptys: 5Fwd Alls: 0Fwd Unregistered: 0Total valid GMRP Packets Transmitted: 600Join Emptys: 200Join INs: 150Leaves: 45Leave Alls: 200Emptys: 5Fwd Alls: 0Fwd Unregistered: 0Total valid GMRP Packets Received: 0Total GMRP packets dropped: 0Total GMRP Registrations Failed: 0Console>Related Commands
show gmrp timer
Use the show gmrp timer command to display all the GMRP timers values.
show gmrp timer
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
You can enter the show multicast group command to display GMRP configuration values.
Examples
This example shows how to display all the GMRP timer values:
Console> (enable) show gmrp timerTimer Timer Value(milliseconds)---------------------------------------------Join 200Leave 600Leave All 10000Console> (enable)Related Commands
set garp timer
set gmrp timer
set gvrp timer
show multicast groupshow gvrp configuration
Use the show gvrp configuration command to display GARP VLAN Registration Protocol (GVRP) configuration information, including timer values, whether GVRP and dynamic VLAN creation are enabled, and which ports are running GVRP.
show gvrp configuration
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If the port list exceeds the available line spaces, the list wraps to the next line.
If no ports are GVRP participants, the message output changes from "GVRP Participants running on port_list" to "GVRP Participants running on no ports."
Examples
This example shows how to view GVRP configuration information:
Console> show gvrp configurationGlobal GVRP Configuration:GVRP Feature is currently enabled on the switch.GVRP dynamic VLAN creation is enabled.GVRP Timers(milliseconds)Join = 200Leave = 600LeaveAll = 10000Port based GVRP Configuration:GVRP Status Registration Port-------------- --------------- -------------------------------------------------------Enabled Normal 2/1-2,3/1-8,7/1-24,8/1-24GVRP Participants running on 3/7-8.Console>Related Commands
clear gvrp statistics
set gvrp
set gvrp dynamic-vlan-creation
set gvrp registration
set gvrp timer
show gvrp statisticsshow gvrp statistics
Use the show gvrp statistics command to view GARP VLAN Registration Protocol (GVRP) statistics for a port.
show gvrp statistics [mod/port]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to view GVRP statistics for module 2, port 1:
Console> show gvrp statistics 2/1GVRP enabledGVRP statistics for port 2/1:Total valid pkts rcvd: 18951Total invalid pkts recvd 0General Queries recvd 377Group Specific Queries recvd 0MAC-Based General Queries recvd 0Leaves recvd 14Reports recvd 16741Queries Xmitted 0GS Queries Xmitted 16Reports Xmitted 0Leaves Xmitted 0Failures to add GDA to EARL 0Topology Notifications rcvd 10GVRP packets dropped 0Console>Table 2-22 describes the fields in the show gvrp statistics output.
Related Commands
clear gvrp statistics
set gvrp
set gvrp dynamic-vlan-creation
set gvrp registration
set gvrp timer
show gvrp configurationshow igmp filter
Use the show igmp filter command to display IGMP multicast filtering on the switch.
show igmp filter
Use the show igmp filter profile profile_id match-action command to display the acceptance or denial status of IP addresses by an IGMP multicast filter profile on the switch.
show igmp filter profile profile_id match-action
Use the show igmp filter profile command to list an IP address, or range of addresses, for a specific IGMP multicast filter profile.
show igmp filter profile profile_id
Use the show igmp filter all command to show all IGMP multicast filter profiles.
show igmp filter all
Use the show igmp filter map command to display the association of IGMP multicast filter profiles with a port, a list of ports, or all ports.
show igmp filter map {port_list | all }
Syntax Description
profile_id
Variable that specifies an arbitrary number assigned to a profile.
port_list
Variable that specifies the module/port value, or range of values.
Defaults
By default, the IGMP multicast filter feature shows all IGMP multicast filters
A profile ID value must be established in the show igmp filter profile.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
Configuring IGMP traffic filtering is performed by the switch administrator using CLI and SNMP interfaces.
The following command is an IGMP filter activation command:
show igmp filter
The following commands are port IP multicast filter commands:
show igmp filter profile profile_id match-action
show igmp filter profile profile_id
show igmp filter map { port_list | all }
Examples
This example shows the status of enabled IGMP multicast filtering on a switch:
Console> (enable) show igmp filterigmp filter is enabledConsole> (enable)This example shows the status of disabled IGMP multicast filtering on a switch:
Console> (enable) show igmp filterigmp filter is disabledConsole> (enable)This example shows the status of an IGMP multicast filter profile to accept IP addresses:
Console> (enable) show igmp filter profile 1 match-actionigmp filter match action is permitConsole> (enable)This example shows the status of an IGMP multicast filter profile to deny IP addresses:
Console> (enable) show igmp filter profile 1 match-actionigmp filter match action is deniedConsole> (enable)This example shows how to list an accepted IP address, or range of addresses, by a specific IGMP multicast filter profile:
Console> (enable) show igmp filter profile 1ProfileId 1: FilterMode permit, IP Range----------------------------------------------------226.1.1.1Console> (enable)This example shows how to list a denied IP address, or range of addresses, by a specific IGMP multicast filter profile:
Console> (enable) show igmp filter profile 1ProfileId 1: FilterMode deny, IP Range----------------------------------------------------226.1.1.1Console> (enable)This example shows how to list all IP addresses for all IGMP multicast filter profiles:
Console> (enable) show igmp filter allProfileId 1: FilterMode deny, IP Range----------------------------------------------------226.1.1.1Console> (enable)This example shows how to display the association of IGMP multicast filter profiles with module 2/port 48.
Console> (enable) show igmp filter map 2/48Port Profile---- -------2/48 -This example shows how to display the association of IGMP multicast filter profiles for all ports.
Console> (enable) show igmp filter map allPort Profile---- -------2/1 12/2 -2/3 -2/4 -2/5 -2/6 -2/7 -2/8 -2/9 -2/10 -2/11 -2/12 -2/13 -2/14 -2/15 -2/16 -2/17 -2/18 -2/19 -2/20 -2/21 -2/22 -2/23 -2/24 -2/25 -2/26 -2/27 -2/28 -2/29 -2/30 -2/31 -2/32 -2/33 -2/34 -2/35 -2/36 -2/37 -2/38 -2/39 -2/40 -2/41 -2/42 -2/43 -2/44 -2/45 -2/46 -2/47 -2/48 -Console> (enable)Related Commands
set igmp filter
clear igmp filtershow imagemib
Use the show imagemib command to display image information provided in the CISCO-IMAGE-MIB for a particular image.
show imagemib filename
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display CISCO-IMAGE-MIB information for the Flash device on the supervisor engine module:
Console> show imagemib cat4000.4-4-0-14.binshow mib info for file cat4000.4-4-0-14.binshow_presto_nmp_image_header : open file cat4000.4-4-0-14.bin error code = -3, )Console>show interface—ROM monitor
Use the show interface command to display information about network interfaces.
show interface
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Examples
This example shows how to display information on all network interfaces:
rommon 1 > show interfaceme1: inet 172.20.52.37 netmask 255.255.255.248 broadcast 172.20.52.39rommon 2 >Related Commands
show interface—switch
Use the show interface command to display information about network interfaces and standard SNMP link trap operation.
show interface
show interface trap
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display information on all network interfaces:
Console> show interfacesl0: flags=50<DOWN,POINTOPOINT,RUNNING>slip 0.0.0.0 dest 0.0.0.0sc0: flags=63<UP,BROADCAST,RUNNING>vlan 100 inet 172.20.52.37 netmask 255.255.255.248 broadcast 172.20.52.39me1: flags=62<DOWN,BROADCAST,RUNNING>inet 172.20.52.37 netmask 255.255.255.224 broadcast 172.20.52.63Console>This example shows how to display whether the trap interface is enabled or disabled:
Console> (enable) show interface trapInterface Trap-------- ----sc0 enabledme1 disabledsl0 disabledConsole> (enable)Table 2-23 describes the fields in the show interface command output.
Related Commands
show ip alias
Use the show ip alias command to show a listing of defined IP aliases.
show ip alias [name]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display a listing of all IP aliases:
Console> show ip aliasdefault 0.0.0.0sparc20 192.168.10.69cat5500-1 172.16.169.16cat5500-2 172.16.169.20Console>Related Commands
show ip dns
Use the show ip dns command to show the DNS name servers and the default DNS domain name.
show ip dns
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the DNS name servers and the default DNS domain name:
Console> show ip dnsDNS is currently enabled.The default DNS domain name is: cisco.comDNS name server status--------------- -------172.16.30.32192.168.2.132 primary172.31.128.70Console>Table 2-24 describes the fields in the show ip dns command output.
Related Commands
clear ip dns domain
clear ip dns server
set ip dns
set ip dns domain
set ip dns servershow ip http
Use the show ip http command to view the HTTP configuration and switch web interface information.
show ip http
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the HTTP configuration and web interface information if the web interface is supported:
Console> show ip httpHTTP Configuration Information:----------------HTTP Server: enabledHTTP port: 80Web Interface: SupportedSwitch Information:------------------File: applet.htmlsize: 912 bytesversion: 5.0(0.26)date: 10/9/99File: cvembopt.jarsize: 3500000 bytesversion: 5.0(0.26)date: 10/9/99Active Web Interface Session: 1-----------------------------Client IP Address: 192.20.20.45Request Type: GETRequest URI: /all-engine.jarConsole>This example shows the HTTP configuration and web interface information if the web interface is not supported:
Console> show ip httpHTTP Configuration Information:----------------HTTP Server: disabledHTTP port: 80Web Interface: Not SupportedConsole>Related Commands
set ip http port
set ip http servershow ip permit
Use the show ip permit command to display the IP permit list information.
show ip permit [noalias]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display IP permit list information:
Console> (enable) show ip permitTelnet permit list feature enabled.Snmp permit list feature disabled.Permit List Mask Access-Type---------------- --------------- ---------------172.16.0.0 255.255.0.0 telnet172.20.52.3 snmp telnet172.20.52.32 255.255.255.224 sshDenied IP Address Last Accessed Time Type Telnet Count SNMP Count----------------- ------------------ ------ ------------ ----------172.100.101.104 01/20/97,07:45:20 SNMP 14 1430172.187.206.222 01/21/97,14:23:05 Telnet 7 236Console> (enable)Table 2-25 describes the fields in the show ip permit command output.
Related Commands
clear ip permit
set ip permit
set snmp trapshow ip route—ROM monitor
Use the show ip route command to display IP routing table entries.
show ip route
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
ROM monitor command.
Command Modes
Normal.
Examples
This example shows how to display IP routing table entries:
rommon 1 > show ip routeDestination Gateway Interface----------------------- ----------------------- ---------default 172.20.52.33 me1rommon 2 >Related Commands
clear ip route—ROM monitor
set ip route—ROM monitorshow ip route—switch
Use the show ip route command to display IP routing table entries.
show ip route [noalias]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the IP route table:
Console> (enable) show ip routeFragmentation Redirect Unreachable------------- -------- -----------enabled enabled enabledDestination Gateway RouteMask Flags Use Interface--------------- --------------- ---------- ----- -------- ---------default 172.20.52.1 0x0 UG 73439 sc0172.20.52.0 172.20.52.5 0xffffffe0 U 4 sc0default default 0xff000000 UH 0 sl0Console> (enable)Table 2-26 describes the fields in the show ip route command output.
Related Commands
clear ip route—switch
set ip route—switchshow kerberos
Use the show kerberos command to display information about a Kerberos configuration.
show kerberos
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display Kerberos configuration information:
kerberos> (enable) show kerberosKerberos Local Realm:CISCO.COMKerberos server entries:Realm:CISCO.COM, Server:187.0.2.1, Port:750Kerberos Domain<->Realm entries:Domain:cisco.com, Realm:CISCO.COMKerberos Clients NOT MandatoryKerberos Credentials Forwarding EnabledKerberos Pre Authentication Method set to NoneKerberos config key:Kerberos SRVTAB EntriesSrvtab Entry 1:host/niners.cisco.com@CISCO.COM 0 932423923 1 1 8 01;;8>00>50;0=0=0kerberos> (enable)Table 2-27 describes the fields in the show kerberos command output.
Related Commands
show kerberos creds
Use the show kerberos creds command to display the Kerberos credentials on a switch.
show kerberos creds
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display Kerberos credentials information:
Console> (enable) show kerberos credsNo Kerberos credentials.Console> (enable)Related Commands
show lacp-channel
Use the show lacp-channel command set to display information about the LACP channel.
show lacp-channel
show lacp-channel sys-id
show lacp-channel group [admin-key] [info [type] | statistics]
show lacp-channel [channel_id] [info [type] | statistics | mac]
show lacp-channel hash channel_id {{src_ip_addr [dest_ip_addr]} | dest_ip_addr | {src_mac_addr [dest_mac_addr]} | dest_mac_addr | {src_port dest_port} | dest_port}
show lacp-channel traffic [channel_id]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If you do not specify admin-key, information about all LACP channels is displayed.
If you do not specify channel_id, information about all LACP channels is displayed.
Examples
This example shows how to display information about all LACP channels:
Console> show lacp-channel groupAdmin Key Ports----------- ------69 4/1-270 4/5-6143 2/1-2151 4/3-4152 4/7-8Console>This example shows how to display limited information about ports that are assigned to administrative key 152:
Console> show lacp-channel group 152Port Channel Admin Ch Partner Oper PartnerMode Key id Sys ID Port----- --------- ----- ---- --------------------------------- -------4/7 active 152 770 8000,AC-12-24-56-78-90 4/34/8 active 152 770 8000,AC-12-24-56-78-90 4/4Console>This example shows how to display detailed information about ports that are assigned to administrative key 152:
Console> show lacp-channel group 152 infoI = Isolated Port. C = Channeling Port. N = Not Connected.H = Hot Stand-by Port. S = Suspended Port.Port LACP Port Port Speed Duplex VLANs Trunk status Port STP Port PortSecurity/Priority Status Cost Priority Dynamic Port----- --------- ----- ----- ------ ------ ------------ ----- -------- ------------4/7 130 C 1000 full 1-1005 not-trunking 4 324/8 131 C 1000 full 1-1005 not-trunking 4 32Port Admin Channel if- Partner Oper Partner Partner PartnerKey id Index Sys ID Port Prior Port Oper Key----- ----- ------- ----- ------------------------- ---------- -------- ----------4/7 152 770 31 800,AC-12-24-56-78-90 248 4/3 157684/8 152 770 31 800,AC-12-24-56-78-90 249 4/4 15768Console>This example shows how to display LACP Tx and Rx statistics for ports that are assigned to administrative key 152:
Console> show lacp-channel group 152 statisticsPort Admin LACP Pkts LACP Pkts Marker Pkts Marker Pkts LACP PktsKey Transmitted Received Transmitted Received Errors----- ------- ----------- --------- ----------- ----------- ---------4/7 152 0 92 0 0 04/8 152 0 0 0 0 0Console>This example shows how to display all ports that are assigned to an administrative key:
Console> show lacp-channel group infoI = Isolated Port. C = Channeling Port. N = Not Connected.H = Hot Stand-by Port. S = Suspended Port.Port LACP Port Port Speed Duplex VLANs Trunk status Port STP Port PortSecurity/Priority Status Cost Priority Dynamic Port----- --------- ----- ----- ------ ------ ------------ ----- -------- ------------4/1 50 I 1000 full 1-1005 not-trunking 4 324/2 51 I 1000 full 1-1005 not-trunking 4 324/5 27 I 1000 full 1-1005 not-trunking 4 324/5 27 I 1000 full 1-1005 not-trunking 4 322/1 133 C 1000 full 1-1005 not-trunking 4 322/2 134 C 1000 full 1-1005 not-trunking 4 324/3 200 C 1000 full 1-1005 not-trunking 4 324/4 201 C 1000 full 1-1005 not-trunking 4 324/7 130 C 1000 full 1-1005 not-trunking 4 324/8 131 C 1000 full 1-1005 not-trunking 4 32Port Admin Channel if- Partner Oper Partner Partner PartnerKey id Index Sys ID Port Prior Port Oper Key----- ------- ------- ----- -------------------------- ----------- ------- --------4/1 69 0 - 0,00-00-00-00-00-00 0 3/1 04/2 69 0 - 0,00-00-00-00-00-00 0 4/5 04/5 70 0 - 0,00-00-00-00-00-00 0 7/3 04/6 70 0 - 0,00-00-00-00-00-00 0 7/4 02/1 143 768 29 1276,45-12-24-AC-78-90 34 5/1 56582/2 143 768 29 1276,45-12-24-AC-78-90 35 5/2 56584/3 151 769 30 13459,89-BC-24-56-78-90 200 1/1 97684/4 151 769 30 13459,89-BC-24-56-78-90 201 1/2 97684/7 152 770 31 8000,AC-12-24-56-78-90 248 4/3 156784/8 152 770 31 8000,AC-12-24-56-78-90 249 4/4 15768Console>This example shows how to display Tx and Rx statistics for all ports that are assigned to an administrative key:
Console> show lacp-channel group statisticsPort Admin LACP Pkts LACP Pkts Marker Pkts Marker Pkts LACP PktsKey Transmitted Received Transmitted Received Errors----- ------- ----------- --------- ----------- ----------- ---------4/1 69 0 0 0 0 04/2 69 0 0 0 0 04/5 70 0 0 0 0 04/6 70 0 0 0 0 02/1 143 0 0 0 0 02/2 143 0 0 0 0 04/3 151 0 0 0 0 04/4 151 0 0 0 0 04/7 152 0 92 0 0 04/8 152 0 0 0 0 0Console>This example shows how to display the outgoing port for the specified source and destination IP addresses:
Console> (enable) show lacp-channel hash 808 172.20.32.10 172.20.32.66Selected channel port:2/17Console> (enable)
This example shows how to display traffic utilization on channel ports:
Console> (enable) show lacp-channel trafficChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst------ ----- ------- ------- ------- ------- ------- -------808 2/16 0.00% 0.00% 50.00% 75.75% 0.00% 0.00%808 2/17 0.00% 0.00% 50.00% 25.25% 0.00% 0.00%816 2/31 0.00% 0.00% 25.25% 50.50% 0.00% 0.00%816 2/32 0.00% 0.00% 75.75% 50.50% 0.00% 0.00%Console> (enable)Related Commands
clear lacp-channel statistics
set channelprotocol
set lacp-channel system-priority
set port lacp-channel
set spantree channelcost
set spantree channelvlancost
show port lacp-channelshow log
Use the show log command to display the error log for a system or for a specific module.
show log [mod]
show log dump [-count]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
To display the contents of ASIC error messages as soon as they are received from SLCP/LCP, use the set logging server command.
You can use the dump keyword to display log dump information generated when certain events occur, such as memory corruption.
Examples
This example shows how to display the error log for the system:
Console> show logNetwork Management Processor (ACTIVE NMP) Log:Reset count: 26Re-boot History: Jan 05 2001 14:27:13 0, Jan 05 2001 14:20:50 0Dec 27 2000 10:18:30 0, Nov 22 2000 15:03:15 0Nov 21 2000 14:52:26 0, Nov 13 2000 09:13:20 0Bootrom Checksum Failures: 0 UART Failures: 0Flash Checksum Failures: 0 Flash Program Failures: 0Power Supply 1 Failures: 0 Power Supply 2 Failures: 2DRAM Failures: 0Exceptions: 0Loaded NMP version: 6.2(1)Reload same NMP version count: 0Last software reset by user: 1/5/2001,14:26:35MCP Exceptions/Hang: 0Heap Memory Log:Corrupted Block = noneNVRAM log:01. 7/26/1999,15:57:51: convertCiscoMIB:PreSac(0) checksum failed: 0x0(0x4C5C)02. 12/27/2000,10:18:30: convert_post_SAC_CiscoMIB:Block 0 converted from version 13 to 1403. 12/27/2000,10:18:33: supVersion:Nmp version 6.2(0.57)KEY04. 1/5/2001,14:27:17: supVersion:Nmp version 6.2(1)Module 2 Log:Reset Count: 12Reset History: Fri Jan 5 2001, 14:27:23Fri Jan 5 2001, 14:21:00Wed Dec 27 2000, 10:18:40Wed Nov 22 2000, 15:03:25Module 3 Log:Reset Count: 12Reset History: Fri Jan 5 2001, 14:27:24Fri Jan 5 2001, 14:21:01Wed Dec 27 2000, 10:18:40Wed Nov 22 2000, 15:03:25NOTE: Use "show crashdump 1" to see the crashdump.Console>Table 2-28 describes the fields in the show log command output.
This example shows how to display dump log information:
Console> show log dumpTotal logs: 1Console>Related Commands
show log command
Use the show log command to display command log entries.
show log command [mod]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Privileged.
Usage Guidelines
The command log entry table is a history log of the commands to the switch from the console or from Telnet.
Examples
This example shows how to display the command log for module 1:
Console> (enable) show log command 1Active Command log:001. Oct 04 09:44:35 Pid = 86 show mod002. Oct 04 09:44:55 Pid = 86 clear log command 3003. Oct 04 10:09:07 Pid = 86 show port membership004. Oct 04 10:10:15 Pid = 86 enable005. Oct 04 10:10:19 Pid = 86 clear port help006. Oct 04 10:10:47 Pid = 86 clear spantree help007. Oct 04 10:12:42 Pid = 86 show008. Oct 04 10:12:57 Pid = 86 show qos help009. Oct 04 10:14:46 Pid = 86 show log 5010. Oct 04 10:14:53 Pid = 86 show log 1011. Oct 04 10:15:04 Pid = 86 show log command 5012. Oct 04 10:15:08 Pid = 86 show log command 1Console> (enable)Related Commands
show logging
Use the show logging command to display the system message log configuration.
show logging [noalias]
Syntax Description
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows the default system message log configuration:
Console <enable> show loggingLogging buffer size: 500timestamp option: enabledLogging history size: 1Logging console: enabledLogging telnet: disabledLogging server: disabledserver facility: LOCAL7server severity: warnings(4)Facility Default Severity Current Session Severity------------- ----------------------- ------------------------cdp 4 4drip 2 2dtp 5 5dvlan 2 2earl 2 2fddi 2 2filesys 2 2gvrp 2 2ip 2 2kernel 2 2mcast 2 2mgmt 5 5mls 5 5pagp 5 5protfilt 2 2pruning 2 2radius 2 2security 2 2snmp 2 2spantree 2 2sys 5 5tac 2 2tcp 2 2telnet 2 2tftp 2 2udld 4 4vmps 2 2vtp 2 20(emergencies) 1(alerts) 2(critical)3(errors) 4(warnings) 5(notifications)6(information) 7(debugging)Console>Table 2-29 describes the fields in the show logging command output.
Related Commands
clear logging server
set logging buffer
set logging level
set logging server
set logging session
show logging buffershow logging buffer
Use the show logging buffer command to display system messages stored in the internal buffer.
show logging buffer [-] [number_of_messages]
Syntax Description
Defaults
By default, the setting is -20, which displays the last 20 messages in the buffer.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If the - keyword is not used, system messages are displayed from the beginning of the buffer. If number_of_messages is not specified, the last 20 messages in the buffer are displayed.
If the logging timestamp option is enabled, a timestamp is also included in the display. Use the set logging timestamp command to enable the timestamp option.
If the logging timestamp option is enabled, the +00:00 or -00:00 in the output indicates the hours and minutes offset from UTC.
Examples
This example shows how to display all the system messages from the internal buffer; this example displays the output with the timestamp option enabled:
Console <enable> show logging buffer1999 Mar 09 19:33:05 +00:00%SYS-5:Module 1 is online1999 Mar 09 19:33:05 +00:00%SYS-5:Module 5 is online1999 Mar 09 19:33:05 +00:00%SYS-5:Module 3 failed configuration1999 Mar 09 19:33:05 +00:00%SYS-5:Module 3 failed configuration1999 Mar 09 19:33:05 +00:00%SYS-5:Module 4 is online1999 Mar 09 19:33:05 +00:00%SNMP-6:Subagent 2 connected1999 Mar 09 19:33:05 +00:00%SNMP-5:Cold Start TrapConsole <enable>This example shows how to display the first four system messages from the internal buffer; this example displays the output with the timestamp option disabled:
Console <enable> show logging buffer 4%SYS-5:Module 1 is online%SYS-5:Module 5 is online%SYS-5:Module 3 failed configurationConsole <enable>This example shows how to display the last four system messages from the internal buffer; this example displays the output with the timestamp option enabled:
Console <enable> show logging buffer -41999 Mar 09 19:33:05 +00:00%SYS-5:Module 3 failed configuration1999 Mar 09 19:33:05 +00:00%SYS-5:Module 4 is online1999 Mar 09 19:33:05 +00:00%SNMP-6:Subagent 2 connected1999 Mar 09 19:33:05 +00:00%SNMP-5:Cold Start TrapConsole <enable>Related Commands
set logging buffer
set logging timestampshow mac
Use the show mac command to display MAC counters.
show mac [mod_num[/port_num]]
Syntax Description
mod_num
(Optional) Variable that specifies the number of the module.
/port_num
(Optional) Variable that specifies the number of the port on the module.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If you do not specify a module number, all modules are shown.
If you do not specify a port number, all ports are shown.
Examples
This example shows how to display MAC information for port 4 on module 3:
Console> show mac 3/4MAC Rcv-Frms Xmit-Frms Rcv-Multi Xmit-Multi Rcv-Broad Xmit-Broad-------- ---------- ---------- ---------- ---------- ---------- ----------3/4 0 0 0 0 0 0MAC Dely-Exced MTU-Exced In-Discard Lrn-Discrd In-Lost Out-Lost-------- ---------- ---------- ---------- ---------- ---------- ----------3/4 0 0 0 0 0 0MAC SMT-Address Curr-Path TReq TNeg TMax TVX------- ----------------- ---------- -------- -------- -------- --------3/4 00:06:7c:b3:bc:98 primary 165000 165000 165004 250900-60-3e-cd-3d-19MAC Upstream-Nbr Downstream-Nbr Old-Upstrm-Nbr Old-Downstrm-Nbr------- ----------------- ----------------- ----------------- -----------------3/4 00:00:1f:00:00:00 00:00:1f:00:00:00 00:00:1f:00:00:00 00:00:1f:00:00:0000-00-f8-00-00-00 00-00-f8-00-00-00 00-00-f8-00-00-00 00-00-f8-00-00-00MAC Rcv-Smt Xmit-Smt Rcv-llc Xmit-llc Tvx-Exp-Ct RingOp-Ct------- ---------- ---------- ---------- ---------- ---------- ----------3/4 0 0 1 61 0 1Port Rcv-Unicast Rcv-Multicast Rcv-Broadcast-------- -------------------- -------------------- --------------------3/4 0 0 0Port Xmit-Unicast Xmit-Multicast Xmit-Broadcast-------- -------------------- -------------------- --------------------3/4 0 0 0Port Rcv-Octet Xmit-Octet-------- -------------------- --------------------3/4 0 0Last-Time-Cleared--------------------------Tue Apr 13 1999, 08:31:20Console>Table 2-30 describes possible fields displayed in the show mac command output.
show module
Use the show module command to display module status and information.
show module [mod_num]
Syntax Description
mod_num
(Optional) Variable that specifies the number of the module. If a module number is not specified, all modules are displayed.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Usage Guidelines
If you delete a module and replace it with a different type module, a message appears in the show module display that states that the module configuration is inconsistent with the current module type. To clear the message, you can either enter the clear config mod_num command for the module or set different parameters for the new module.
For Catalyst 4000 family switches, the show module command displays the supervisor engine as having "1" slot.
For Catalyst 4000 family switches, in the show module command display, the combination of the 32-port module (WS-X4502) and 4-port 100FX card results in an entry that reads 36 ports. If the uplink card is not installed, only ports 1 to 32 are listed.
Although me1 resides on the supervisor engine module for the Catalyst 4000 family switches, me1 port information is not displayed by the show module or show port commands.
Examples
This example shows how to display status and information for module 3:
Console> show module 3Mod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------3 3 9 Gigabit Ethernet WS-X5410 no okMod Module-Name Serial-Num--- ------------------- --------------------3 00007285650Mod MAC-Address(es) Hw Fw Sw--- -------------------------------------- ------ ---------- -----------------3 00-e0-1e-38-48-cc to 00-e0-1e-38-48-d7 0.2 4.1(0.53-E 5.1(0.59))Console>This example shows how to display status and information for the Catalyst 4000 family switch:
Console> show moduleMod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------1 1 0 Switching Supervisor WS-X4012 yes ok2 2 6 1000BaseX Ethernet Ext WS-X43063 3 6 1000BaseX Ethernet WS-X4306 no okMod Module-Name Serial-Num--- ------------------- --------------------1 JAB023806JR2 JAB0240004D3 JAB024000YYMod MAC-Address(es) Hw Fw Sw--- -------------------------------------- ------ ---------- -----------------1 00-10-7b-f8-03-00 to 00-10-7b-f8-06-ff 0.1 4.4(0.14) 5.1(0.57)2 00-10-7b-f6-b1-a8 to 00-10-7b-f6-b1-ad 0.23 00-10-7b-f6-b2-1a to 00-10-7b-f6-b2-1f 0.2Console>Table 2-31 describes the possible fields in the show module command output.
Table 2-31 show module Command Output Fields
Mod
Module number.
Slot
Slot number.
Module-Name
Name of the module (if configured).
Ports
Number of ports on the module.
Module-Type
Module type (such as 10BASE-T Ethernet or Token Ring).
Model
Model number of the module.
Serial-Num
Serial number of the module.
Status
Status of the module. Possible status strings are ok, disable, faulty, other, standby, and error.
MAC-Address(es)
MAC address or MAC address range for the module. Token Ring module MAC addresses appear in noncanonical format.
Hw
Hardware version of the module1 .
Fw
Firmware version of the module2 .
Sw
Software version on the module.
SMT User-Data
User-data string defined for the FDDI module.
T-Notify
T-Notify timer value configured for the FDDI module.
CF-St
Configuration management state of the FDDI module.
ECM-St
Entity Coordination Management state of the FDDI module.
Bypass
Status of whether an optical bypass switch is present.
Sub-Type3
Submodule type.
Sub-Model3
Model number of the submodule.
Sub-Serial3
Serial number of the submodule.
Sub-Hw3
Hardware version of the submodule.
1 Hw for the supervisor engine module displays the supervisor engine module's EARL hardware version.
2 Fw for the supervisor engine module displays the supervisor engine module's boot version.
3 This field displays EARL information; this field is dd on the Catalyst 4000 family and Catalyst 2948G switches.
show multicast group
Use the show multicast group command to display the multicast group configuration.
show multicast group [mac_addr] [vlan_id]
Syntax Description
mac_addr
(Optional) Variable that specifies the destination MAC address.
vlan_id
(Optional) Variable that specifies the number of the VLAN.
Defaults
This command has no default settings.
Command Types
Switch command.
Command Modes
Normal.
Examples
This example shows how to display the multicast group configuration for VLAN 1:
Console> show multicast group 1VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol Type]---- ----------------- ----- ----------------------------------1 01-00-5e-00-01-28* 3/1,12/91 01-00-5e-63-7f-6f* 3/1,12/5,12/9Total Number of Entries = 2Console>This example shows how to display the multicast group configuration for a specific MAC address on VLAN 5:
Console> show multicast group 01-00-5E-00-00-5C 5VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol Type]---- ----------------- ----- ----------------------------------5 01-00-5E-00-00-5C 3/1, 3/9Total Number of Entries = 1Console>The following table describes the fields in the show multicast group command output.
Related Commands
clear multicast router
set cgmp
set multicast router
show multicast router2
