Contents

• VideoStream Commands
• ap dot11 mediastream
• ap dot11 media-stream multicast-direct
• show ap dot11
• show wireless media-stream group
• wireless media-stream multicast-direct
• wireless media-stream

VideoStream Commands

---

• ap dot11 mediastream
• ap dot11 media-stream multicast-direct
• show ap dot11
• show wireless media-stream group
• wireless media-stream multicast-direct
• wireless media-stream

ap dot11 mediastream

To configure various parameters, use the ap dot11 mediastream command.

ap dot11 { 24ghz | 5ghz } media-stream { multicast-direct | { admission-besteffort | client-maximum value } | video-redirect }

Syntax Description

multicast-direct	Configures multicast-direct.
admission-besteffort	Configures the media stream to still be sent through the best effort queue if a media stream cannot be prioritized due to bandwidth availability limitations.
client-maximum value	Configures maximum number of allowed media streams per individual client.
video-redirect	Configure to redirect unicast video to the Best Effort queue over the air.

Command Default

Disabled

Command Modes

config

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to configure maximum number of allowed media streams per client.

Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#ap dot11 24ghz media-stream multicast-direct 15

ap dot11 media-stream multicast-direct

To configure multicast-direct for 2.4-GHz/5-GHz band, use the ap dot11 media-stream multicast-direct command.

ap dot11 { 24ghz | 5ghz } media-stream { multicast-direct { admission-besteffort | client-maximum value | radio-maximum value } | video-redirect }

Syntax Description

media-stream	Configure media-stream for 802.11 band.
multicast-direct	Configure multicast-direct for 802.11 band
admission-besteffort	Admits media stream to best-effort queue.
client-maximum value	Specifies the maximum number of streams allowed on a client.
radio-maximum value	Specifies the maximum number of streams allowed on a 2.4-GHz or a 5-GHz band.
video-redirect	Redirect non Multicast-direct video to BestEffort queue over the air.

Command Default

None.

Command Modes

config

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Before you configure the media stream multicast-direct parameters on a 802.11 network, ensure that the network is nonoperational.

Examples

This example shows how to configure multicast-direct for the 2.4-GHz band.

Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#ap dot11 24ghz media-stream multicast-direct admission-besteffort

show ap dot11

To display 802.11 band parameters, use the show ap dot11 command.

show ap dot11 { 24ghz | 5ghz } { media-stream rrc | network | profile | summary }

Syntax Description

media-stream rrc	Display Media Stream configurations for 802.11b
network	802.11b network configuration.
profile	Shows 802.11b profiling information for all Cisco APs
summary	Shows configuration and statistics of 802.11b Cisco APs

Command Default

None.

Command Modes

Any command mode

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

None.

This example shows how to display 802.11 Media Resource Reservation Control configurations.

Switch#show ap dot11 24ghz media-stream rrc

Multicast-direct                 : Disabled
Best Effort                      : Disabled
Video Re-Direct                  : Disabled
Max Allowed Streams Per Radio      : Auto
Max Allowed Streams Per Client     : Auto
Max Video Bandwidth               : 0
Max Voice Bandwidth               : 75
Max Media Bandwidth               : 85
Min PHY Rate (Kbps)               : 6000
Max Retry Percentage              : 80

show wireless media-stream group

To display the wireless media-stream group information, use the show wireless media-stream group command.

show wireless media-stream group { detail groupName | summary }

Syntax Description

detail groupName	Display media-stream group configuration details of the group mentioned in the command.
summary	Display media-stream group configuration summary

Command Default

None

Command Modes

Global config.

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

None.

This example shows how to display the details of the media-stream group named GRP1.

Switch#show wireless media-stream group detail GRP1

wireless media-stream multicast-direct

To configure multicast-direct status, use the media-stream multicast-direct command. To remove the multicast-direct status, use the no form of the command.

wireless media-stream multicast-direct

no wireless media-stream multicast-direct

Command Default

None.

Command Modes

wlan

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Media stream multicast-direct requires load based Call Admission Control (CAC) to run. WLAN quality of service (QoS) needs to be set to either gold or platinum.

Examples

This example shows how to configure multicast-direct for a wireless LAN media stream.

Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#wireless media-stream multicast-direct

wireless media-stream

To configure various parameters, use the wireless media-stream command.

wireless media-stream { multicast-direct | message [ phone phone | URL URL | Notes Notes | Email Email ] | group groupName [ startipAddr endipAddr ] }

Syntax Description

multicast-direct	Configure multicast-direct status.
message	Configure Session Announcement Message.
phone phone	Configure Session Announcement Phone number.
URL URL	Configure Session Announcement URL.
Notes Notes	Configure Session Announcement notes.
Email Email	Configure Session Announcement Email.
group groupName	Configure multicast-direct status for a group.
startipAddr	Specifies the start IP Address for the group.
endipAddr	Specifies the End IP Address for the group.

Command Default

Disabled

Command Modes

config

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Media-stream multicast-direct requires load-based Call Admission Control (CAC) to run.

Examples

This example shows how to configure each media stream and its parameters like expected multicast destination addresses, stream bandwidth consumption and stream priority parameters.

Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#wireless media-stream group GROUP1 231.1.1.1 231.1.1.10