Table Of Contents

rmon collection stats

service password-recovery

service-policy

set

setup

setup express

show access-lists

show archive status

show auto qos

show boot

show cable-diagnostics tdr

show class-map

show cluster

show cluster candidates

show cluster members

show controllers cpu-interface

show controllers ethernet-controller

show controllers tcam

show dot1x

show dtp

show env

show errdisable detect

show errdisable flap-values

show errdisable recovery

show etherchannel

show flowcontrol

show interfaces

show interfaces counters

show ip dhcp snooping

show ip dhcp snooping binding

show ip igmp profile

show ip igmp snooping

show ip igmp snooping mrouter

show ip igmp snooping groups

show lacp

show mac access-group

show mac address-table

show mac address-table address

show mac address-table aging-time

show mac address-table count

show mac address-table dynamic

show mac address-table interface

show mac address-table notification

show mac address-table static

show mac address-table vlan

show mls qos

show mls qos aggregate-policer

show mls qos input-queue

show mls qos interface

show mls qos maps

show mls qos queue-set

show monitor

show mvr

show mvr interface

show mvr members

show pagp

show parser macro

show policy-map

show port-security

show sdm prefer

show setup express

show spanning-tree

show storm-control

show system mtu

show udld

show version

show vlan

show vlan access-map

show vlan filter

show vmps

show vtp

2]

rmon collection stats

Use the rmon collection stats interface configuration command to collect Ethernet group statistics, which include usage statistics about broadcast and multicast packets, and error statistics about cyclic redundancy check (CRC) alignment errors and collisions. Use the no form of this command to return to the default setting.

rmon collection stats index [owner name]

no rmon collection stats index [owner name]

Syntax Description

index	Remote Network Monitoring (RMON) collection control index. The range is 1 to 65535.
owner name	(Optional) Owner of the RMON collection.

Defaults

The RMON statistics collection is disabled.

Command Modes

Interface configuration

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

The RMON statistics collection command is based on hardware counters.

Examples

This example shows how to collect RMON statistics for the owner root:

Switch(config)# interface gigabitethernet0/1

Switch(config-if)# rmon collection stats 2 owner root

You can verify your setting by entering the show rmon statistics privileged EXEC command.

Related Commands

Command	Description
show rmon statistics	Displays RMON statistics. For syntax information, select Cisco IOS Configuration Fundamentals Command Reference, Release 12.2 > System Management Commands > RMON Commands.

service password-recovery

Use the service password-recovery global configuration command to enable the password-recovery mechanism (the default). This mechanism allows an end user with physical access to the switch to hold down the Mode button and interrupt the boot process while the switch is powering up and to assign a new password. Use the no form of this command to disable part of the password-recovery functionality. When the password-recovery mechanism is disabled, interrupting the boot process is allowed only if the user agrees to set the system back to the default configuration.

service password-recovery

no service password-recovery

Syntax Description

This command has no arguments or keywords.

Defaults

The password-recovery mechanism is enabled.

Command Modes

Global configuration

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

As a system administrator, you can use the no service password-recovery command to disable some of the functionality of the password recovery feature by allowing an end user to reset a password only by agreeing to return to the default configuration.

The password-recovery mechanism has been triggered, but

is currently disabled.  Access to the boot loader prompt

through the password-recovery mechanism is disallowed at

this point.  However, if you agree to let the system be

reset back to the default system configuration, access

to the boot loader prompt can still be allowed.

Would you like to reset the system back to the default configuration (y/n)?

If the user chooses not to reset the system back to the default configuration, the normal boot process continues, as if the Mode button had not been pressed. If you choose to reset the system back to the default configuration, the configuration file in flash memory is deleted, and the VLAN database file, flash:vlan.dat (if present), is deleted.

---

Note If you use the no service password-recovery command to control end user access to passwords, we recommend that you save a copy of the config file in a location away from the switch in case the end user uses the password recovery procedure and sets the system back to default values. Do not keep a backup copy of the config file on the switch.

If the switch is operating in VTP transparent mode, we recommend that you also save a copy of the vlan.dat file in a location away from the switch.

---

You can verify if password recovery is enabled or disabled by entering the show version privileged EXEC command.

Examples

This example shows how to disable password recovery on a switch so that a user can only reset a password by agreeing to return to the default configuration.

Switch(config)# no service-password recovery

Switch(config)# exit

Related Commands

Command	Description
show version	Displays version information for the hardware and firmware.

service-policy

Use the service-policy interface configuration command to apply a policy map defined by the policy-map command to the input of a port. Use the no form of this command to remove the policy map and port association.

service-policy input policy-map-name

no service-policy input policy-map-name

Syntax Description

input policy-map-name

Apply the specified policy-map to the input of a port.

---

Note Though visible in the command-line help strings, the history keyword is not supported, and you should ignore the statistics that it gathers. The output keyword is also not supported.

---

Defaults

No policy maps are attached to the port.

Command Modes

Interface configuration

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Only one policy map per ingress port is supported.

Classification using a port trust state (for example, mls qos trust [cos | dscp | ip-precedence] and a policy map (for example, service-policy input policy-map-name) are mutually exclusive. The last one configured overwrites the previous configuration.

Examples

This example shows how to apply plcmap1 to an ingress port:

Switch(config)# interface gigabitethernet0/1

Switch(config-if)# service-policy input plcmap1

This example shows how to remove plcmap2 from a port:

Switch(config)# interface gigabitethernet0/2

Switch(config-if)# no service-policy input plcmap2

You can verify your settings by entering the show running-config privileged EXEC command.

Related Commands

Command	Description
policy-map	Creates or modifies a policy map that can be attached to multiple ports to specify a service policy.
show policy-map	Displays quality of service (QoS) policy maps.

set

Use the set policy-map class configuration command to classify IP traffic by setting a Differentiated Services Code Point (DSCP) or an IP-precedence value in the packet. Use the no form of this command to remove traffic classification.

set {ip dscp new-dscp | ip precedence new-precedence}

no set {ip dscp new-dscp | ip precedence new-precedence}

Syntax Description

ip dscp new-dscp	New DSCP value assigned to the classified traffic. The range is 0 to 63. You also can enter a mnemonic name for a commonly used value.
ip precedence new-precedence	New IP-precedence value assigned to the classified traffic. The range is 0 to 7. You also can enter a mnemonic name for a commonly used value.

Defaults

No traffic classification is defined.

Command Modes

Policy-map class configuration

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

The set command is mutually exclusive with the trust policy-map class configuration command within the same policy map.

For the set ip dscp new-dscp or the set ip precedence new-precedence command, you can enter a mnemonic name for a commonly used value. For example, you can enter the set ip dscp af11 command, which is the as same entering the set ip dscp 10 command. You can enter the set ip precedence critical command, which is the same as entering the set ip precedence 5 command. For a list of supported mnemonics, enter the set ip dscp ? or the set ip precedence ? command to see the command-line help strings.

To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use the end command.

Examples

This example shows how to assign DSCP 10 to all FTP traffic without any policers:

Switch(config)# policy-map policy_ftp

Switch(config-pmap)# class ftp_class

Switch(config-pmap-c)# set ip dscp 10

Switch(config-pmap)# exit

You can verify your settings by entering the show policy-map privileged EXEC command.

Related Commands

Command	Description
class	Defines a traffic classification match criteria (through the police, set, and trust policy-map class configuration commands) for the specified class-map name.
police	Defines a policer for classified traffic.
policy-map	Creates or modifies a policy map that can be attached to multiple ports to specify a service policy.
show policy-map	Displays quality of service (QoS) policy maps.
trust	Defines a trust state for traffic classified through the class policy-map configuration command or the class-map global configuration command.

setup

Use the setup privileged EXEC command to configure the switch with its initial configuration.

setup

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

When you use the setup command, make sure that you have this information:

•IP address and network mask

•Password strategy for your environment

•Whether the switch will be used as the cluster command switch and the cluster name

When you enter the setup command, an interactive dialog, called the System Configuration Dialog, appears. It guides you through the configuration process and prompts you for information. The values shown in brackets next to each prompt are the default values last set by using either the setup command facility or the configure privileged EXEC command.

Help text is provided for each prompt. To access help text, press the question mark (?) key at a prompt.

To return to the privileged EXEC prompt without making changes and without running through the entire System Configuration Dialog, press Ctrl-C.

When you complete your changes, the setup program shows you the configuration command script that was created during the setup session. You can save the configuration in NVRAM, or return to the setup program or the command-line prompt without saving it.

Examples

This is an example of output from the setup command:

Switch# setup

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity

for management of the system, extended setup will ask you

to configure each interface on the system.

Would you like to enter basic management setup? [yes/no]: yes

Configuring global parameters:

Enter host name [Switch]:host-name

  The enable secret is a password used to protect access to

  privileged EXEC and configuration modes. This password, after

  entered, becomes encrypted in the configuration.

  Enter enable secret: enable-secret-password

  The enable password is used when you do not specify an

  enable secret password, with some older software versions, and

  some boot images.

  Enter enable password: enable-password

  The virtual terminal password is used to protect

  access to the router over a network interface.

  Enter virtual terminal password: terminal-password

  Configure SNMP Network Management? [no]: yes

  Community string [public]: 

Current interface summary

Any interface listed with OK? value "NO" does not have a valid configuration

Interface                  IP-Address      OK? Method Status                Protocol

Vlan1                      172.20.135.202  YES NVRAM  up                    up

GigabitEthernet0/1         unassigned      YES unset  up                    up

GigabitEthernet0/2         unassigned      YES unset  up                    down

<output truncated>

Port-channel1              unassigned      YES unset  up                    down

Enter interface name used to connect to the

management network from the above interface summary: vlan1

Configuring interface vlan1:

Configure IP on this interface? [yes]: yes 

IP address for this interface: ip_address

Subnet mask for this interface [255.0.0.0]: subnet_mask

Would you like to enable as a cluster command switch? [yes/no]: yes

Enter cluster name: cluster-name

The following configuration command script was created:

hostname host-name

enable secret 5 $1$LiBw$0Xc1wyT.PXPkuhFwqyhVi0

enable password enable-password

line vty 0 15

password terminal-password

snmp-server community public

!

no ip routing

!

interface GigabitEthernet0/1

no ip address

!

interface GigabitEthernet0/2

no ip address

! 

cluster enable cluster-name

!

end

Use this configuration? [yes/no]: yes

!

[0] Go to the IOS command prompt without saving this config.

[1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit.

Enter your selection [2]:

Related Commands

Command	Description
show running-config	Displays the running configuration on the switch. For syntax information, select Cisco IOS Configuration Fundamentals Command Reference, Release 12.2 > File Management Commands > Configuration File Management Commands.
show version	Displays version information for the hardware and firmware.

setup express

Use the setup express global configuration command to enable Express Setup mode. Use the no form of this command to disable Express Setup mode.

setup express

no setup express

Syntax Description

This command has no arguments or keywords.

Defaults

Express Setup is enabled.

Command Modes

Global configuration

Command History

Release	Modification
12.1(14)EA1	This command was introduced.

Usage Guidelines

When Express Setup is enabled on a new (unconfigured) switch, pressing the Mode button for 2 seconds activates Express Setup. You can access the switch through an Ethernet port by using the IP address 10.0.0.1 and then can configure the switch with the web-based Express Setup program or the command-line interface (CLI)-based setup program.

When you press the Mode button for 2 seconds on a configured switch, the LEDs above the Mode button start blinking. If you press the Mode button for a total of 10 seconds, the switch configuration is deleted, and the switch reboots. The switch can then be configured like a new switch, either through the web-based Express Setup program or the CLI-based setup program.

---

Note As soon as you make any change to the switch configuration (including entering no at the beginning of the CLI-based setup program), configuration by Express Setup is no longer available. You can only run Express Setup again by pressing the Mode button for 10 seconds. This deletes the switch configuration and reboots the switch.

---

If Express Setup is active on the switch, entering the write memory or copy running-configuration startup-configuration privileged EXEC commands deactivates Express Setup. The IP address 10.0.0.1 is no longer valid on the switch, and your connection using this IP address ends.

The primary purpose of the no setup express command is to prevent someone from deleting the switch configuration by pressing the Mode button for 10 seconds.

Examples

This example shows how to enable Express Setup mode:

Switch(config)# setup express

You can verify that Express Setup mode is enabled by pressing the Mode button:

•On an unconfigured switch, the LEDs above the Mode button turn solid green after 3 seconds.

•On a configured switch, the mode LEDs begin blinking after 2 seconds and turn solid green after 10 seconds.

---

Caution If you hold the Mode button down for a total of 10 seconds, the configuration is deleted, and the switch reboots.

---

This example shows how to disable Express Setup mode:

Switch(config)# no setup express

You can verify that Express Setup mode is disabled by pressing the Mode button. The mode LEDs do not turn solid green or begin blinking green if Express Setup mode is not enabled on the switch.

Related Commands

Command	Description
clear setup express	Exits Express Setup mode.
show setup express	Displays if Express Setup mode is active.

show access-lists

Use the show access-lists privileged EXEC command to display access control lists (ACLs) configured on the switch.

show access-lists [name | number | hardware counters | ipc] [ | {begin | exclude | include} expression]

Syntax Description

name	(Optional) Name of the ACL.
number	(Optional) ACL number. The range is 1 to 2699.
hardware counters	(Optional) Display global hardware ACL statistics for switched and routed packets.
ipc	(Optional) Display Interprocess Communication (IPC) protocol access-list configuration download information.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

---

Note Though visible in the command-line help strings, the rate-limit keywords are not supported.

---

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(14)EA1	The ipc keyword was added.

Usage Guidelines

The switch supports only IP standard and extended access lists. Therefore, the allowed numbers are only 1 to 199 and 1300 to 2699.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show access-lists command:

Switch# show access-lists

Standard IP access list 1

    10 permit 1.1.1.1

    20 permit 2.2.2.2

    30 permit any

    40 permit 0.255.255.255, wildcard bits 12.0.0.0

Standard IP access list videowizard_1-1-1-1

    10 permit 1.1.1.1

Standard IP access list videowizard_10-10-10-10

    10 permit 10.10.10.10

Extended IP access list 121

    10 permit ahp host 10.10.10.10 host 20.20.10.10 precedence routine

Extended IP access list CMP-NAT-ACL

    Dynamic Cluster-HSRP deny   ip any any

    10 deny ip any host 19.19.11.11

    20 deny ip any host 10.11.12.13

    Dynamic Cluster-NAT permit ip any any

    10 permit ip host 10.99.100.128 any

    20 permit ip host 10.46.22.128 any

    30 permit ip host 10.45.101.64 any

    40 permit ip host 10.45.20.64 any

    50 permit ip host 10.213.43.128 any

    60 permit ip host 10.91.28.64 any

    70 permit ip host 10.99.75.128 any

    80 permit ip host 10.38.49.0 any 

This is an example of output from the show access-lists hardware counters command:

Switch# show access-lists hardware counters

L2 ACL INPUT Statistics

     Drop:                All frame count: 855

     Drop:                All bytes count: 94143

     Drop And Log:        All frame count: 0

     Drop And Log:        All bytes count: 0

     Bridge Only:         All frame count: 0

     Bridge Only:         All bytes count: 0

     Bridge Only And Log: All frame count: 0

     Bridge Only And Log: All bytes count: 0

     Forwarding To CPU:   All frame count: 0

     Forwarding To CPU:   All bytes count: 0

     Forwarded:           All frame count: 2121

     Forwarded:           All bytes count: 180762

     Forwarded And Log:   All frame count: 0

     Forwarded And Log:   All bytes count: 0

 L3 ACL INPUT Statistics

     Drop:                All frame count: 0

     Drop:                All bytes count: 0

     Drop And Log:        All frame count: 0

     Drop And Log:        All bytes count: 0

     Bridge Only:         All frame count: 0

     Bridge Only:         All bytes count: 0

     Bridge Only And Log: All frame count: 0

     Bridge Only And Log: All bytes count: 0

     Forwarding To CPU:   All frame count: 0

     Forwarding To CPU:   All bytes count: 0

     Forwarded:           All frame count: 13586

     Forwarded:           All bytes count: 1236182

     Forwarded And Log:   All frame count: 0

     Forwarded And Log:   All bytes count: 0

 L2 ACL OUTPUT Statistics

     Drop:                All frame count: 0

     Drop:                All bytes count: 0

     Drop And Log:        All frame count: 0

     Drop And Log:        All bytes count: 0

     Bridge Only:         All frame count: 0

     Bridge Only:         All bytes count: 0

     Bridge Only And Log: All frame count: 0

     Bridge Only And Log: All bytes count: 0

     Forwarding To CPU:   All frame count: 0

     Forwarding To CPU:   All bytes count: 0

     Forwarded:           All frame count: 232983

     Forwarded:           All bytes count: 16825661

     Forwarded And Log:   All frame count: 0

     Forwarded And Log:   All bytes count: 0

 L3 ACL OUTPUT Statistics

     Drop:                All frame count: 0

     Drop:                All bytes count: 0

     Drop And Log:        All frame count: 0

     Drop And Log:        All bytes count: 0

     Bridge Only:         All frame count: 0

     Bridge Only:         All bytes count: 0

     Bridge Only And Log: All frame count: 0

     Bridge Only And Log: All bytes count: 0

     Forwarding To CPU:   All frame count: 0

     Forwarding To CPU:   All bytes count: 0

     Forwarded:           All frame count: 514434

     Forwarded:           All bytes count: 39048748

     Forwarded And Log:   All frame count: 0

     Forwarded And Log:   All bytes count: 0

Related Commands

Command	Description
access-list	Configures a standard or extended numbered access list on the switch. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.
ip access list	Configures a named IP access list on the switch. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.
mac access-list extended	Configures a named or numbered MAC access list on the switch.

show archive status

Use the show archive status privileged EXEC command to display the status of a new image being downloaded to a switch with the HTTP or TFTP protocol.

show archive status [ {begin | exclude | include} expression]

Syntax Description

begin	(Optional) Display begins with the line that matches the expression.
exclude	(Optional) Display excludes lines that match the expression.
include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.2(20)SE	This command was introduced.

Usage Guidelines

If you use the archive download-sw privileged EXEC command to download an image to a TFTP server, the output of the archive download-sw command shows the status of the download.

If you do not have a TFTP server, you can use the Cluster Management Suite (CMS) to download the image by using the HTTP protocol. The show archive status command shows the progress of the download.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

These are examples of output from the show archive status command:

Switch# show archive status

IDLE: No upgrade in progress

Switch# show archive status

LOADING: Upgrade in progress

Switch# show archive status

EXTRACT: Extracting the image

Switch# show archive status

VERIFY: Verifying software

Switch# show archive status

RELOAD: Upgrade completed. Reload pending

Related Commands

Command	Description
archive download-sw	Downloads a new image from a TFTP server to the switch.

show auto qos

Use the show auto qos user EXEC command to display the quality of service (QoS) commands entered on the interfaces on which automatic QoS (auto-QoS) is enabled.

show auto qos [interface [interface-id]]

Syntax Description

interface [interface-id]

(Optional) Display auto-QoS information for the specified port or for all ports. Valid interfaces include physical ports.

Command Modes

User EXEC

Command History

Release	Modification
12.1(14)EA1	This command was introduced.
12.2(20)SE	The information in the command output changed, and the user guidelines were updated.

Usage Guidelines

In releases earlier than Cisco IOS Release 12.2(20)SE, the show auto qos [interface [interface-id]] command output shows the initial generated auto-QoS configuration.

In Cisco IOS Release 12.2(20)SE or later, the show auto qos command output shows only the auto-QoS command entered on each interface. The show auto qos interface interface-id command output shows the auto-QoS command entered on a specific interface.

Use the show running-config privileged EXEC command to display the auto-QoS configuration and the user modifications.

To display information about the QoS configuration that might be affected by auto-QoS, use one of these commands:

•show mls qos

•show mls qos maps cos-dscp

•show mls qos interface [interface-id] [buffers | queueing]

•show mls qos maps [cos-dscp | cos-input-q | cos-output-q | dscp-cos | dscp-input-q | dscp-output-q]

•show mls qos input-queue

•show running-config

Examples

This is an example of output from the show auto qos command after the auto qos voip cisco-phone and the auto qos voip cisco-softphone interface configuration commands are entered:

Switch> show auto qos 

GigabitEthernet0/4

auto qos voip cisco-softphone

GigabitEthernet0/5

auto qos voip cisco-phone

GigabitEthernet0/6

auto qos voip cisco-phone

This is an example of output from the show auto qos interface interface-id command when the auto 
qos voip cisco-phone interface configuration command is entered:

Switch> show auto qos interface gigabitethernet 0/5

GigabitEthernet0/5

auto qos voip cisco-phone

This is an example of output from the show running-config privileged EXEC command when the auto qos voip cisco-phone and the auto qos voip cisco-softphone interface configuration commands are entered:

Switch# show running-config

Building configuration...

...

mls qos map policed-dscp  24 26 46 to 0

mls qos map cos-dscp 0 8 16 26 32 46 48 56

mls qos srr-queue input bandwidth 90 10

mls qos srr-queue input threshold 1 8 16

mls qos srr-queue input threshold 2 34 66

mls qos srr-queue input buffers 67 33

mls qos srr-queue input cos-map queue 1 threshold 2  1

mls qos srr-queue input cos-map queue 1 threshold 3  0

mls qos srr-queue input cos-map queue 2 threshold 1  2

mls qos srr-queue input cos-map queue 2 threshold 2  4 6 7

mls qos srr-queue input cos-map queue 2 threshold 3  3 5

mls qos srr-queue input dscp-map queue 1 threshold 2  9 10 11 12 13 14 15

mls qos srr-queue input dscp-map queue 1 threshold 3  0 1 2 3 4 5 6 7

mls qos srr-queue input dscp-map queue 1 threshold 3  32

mls qos srr-queue input dscp-map queue 2 threshold 1  16 17 18 19 20 21 22 23

mls qos srr-queue input dscp-map queue 2 threshold 2  33 34 35 36 37 38 39 48

mls qos srr-queue input dscp-map queue 2 threshold 2  49 50 51 52 53 54 55 56

mls qos srr-queue input dscp-map queue 2 threshold 2  57 58 59 60 61 62 63

mls qos srr-queue input dscp-map queue 2 threshold 3  24 25 26 27 28 29 30 31

mls qos srr-queue input dscp-map queue 2 threshold 3  40 41 42 43 44 45 46 47

mls qos srr-queue output cos-map queue 1 threshold 3  5

mls qos srr-queue output cos-map queue 2 threshold 3  3 6 7

mls qos srr-queue output cos-map queue 3 threshold 3  2 4

mls qos srr-queue output cos-map queue 4 threshold 2  1

mls qos srr-queue output cos-map queue 4 threshold 3  0

mls qos srr-queue output dscp-map queue 1 threshold 3  40 41 42 43 44 45 46 47

mls qos srr-queue output dscp-map queue 2 threshold 3  24 25 26 27 28 29 30 31

mls qos srr-queue output dscp-map queue 2 threshold 3  48 49 50 51 52 53 54 55

mls qos srr-queue output dscp-map queue 2 threshold 3  56 57 58 59 60 61 62 63

mls qos srr-queue output dscp-map queue 3 threshold 3  16 17 18 19 20 21 22 23

mls qos srr-queue output dscp-map queue 3 threshold 3  32 33 34 35 36 37 38 39

mls qos srr-queue output dscp-map queue 4 threshold 1  8

mls qos srr-queue output dscp-map queue 4 threshold 2  9 10 11 12 13 14 15

mls qos srr-queue output dscp-map queue 4 threshold 3  0 1 2 3 4 5 6 7

mls qos queue-set output 1 threshold 1 100 100 100 100

mls qos queue-set output 1 threshold 2 75 75 75 250

mls qos queue-set output 1 threshold 3 75 150 100 300

mls qos queue-set output 1 threshold 4 50 100 75 400

mls qos queue-set output 2 threshold 1 100 100 100 100

mls qos queue-set output 2 threshold 2 35 35 35 35

mls qos queue-set output 2 threshold 3 55 82 100 182

mls qos queue-set output 2 threshold 4 90 250 100 400

mls qos queue-set output 1 buffers 15 20 20 45

mls qos queue-set output 2 buffers 24 20 26 30

mls qos

...

!

class-map match-all AutoQoS-VoIP-RTP-Trust

  match ip dscp ef

class-map match-all AutoQoS-VoIP-Control-Trust

  match ip dscp cs3  af31

!

policy-map AutoQoS-Police-SoftPhone

  class AutoQoS-VoIP-RTP-Trust

   set ip dscp ef

    police 320000 8000 exceed-action policed-dscp-transmit

  class AutoQoS-VoIP-Control-Trust

   set ip dscp cs3

    police 32000 8000 exceed-action policed-dscp-transmit

!

...

!

interface GigabitEthernet0/4

 switchport mode access

 switchport port-security maximum 400

 service-policy input AutoQoS-Police-SoftPhone

 speed 100

 duplex half

 srr-queue bandwidth share 10 10 60 20

 srr-queue bandwidth shape  10  0  0  0

 auto qos voip cisco-softphone

!

interface GigabitEthernet0/5

 switchport mode access

 switchport port-security maximum 1999

 speed 100

 duplex full

 srr-queue bandwidth share 10 10 60 20

 srr-queue bandwidth shape  10  0  0  0

 mls qos trust device cisco-phone

 mls qos trust cos

 auto qos voip cisco-phone

!

interface GigabitEthernet0/6

 switchport trunk encapsulation dot1q

 switchport trunk native vlan 2

 switchport mode access

 speed 10

 srr-queue bandwidth share 10 10 60 20

 srr-queue bandwidth shape  10  0  0  0

 mls qos trust device cisco-phone

 mls qos trust cos

 auto qos voip cisco-phone

!

<output truncated>

This is an example of output from the show auto qos interface interface-id command when the auto qos voip cisco-phone interface configuration command is entered:

Switch> show auto qos interface fastethernet0/2

FastEthernet0/2

auto qos voip cisco-phone

These are examples of output from the show auto qos command when auto-QoS is disabled on the switch:

Switch> show auto qos

AutoQoS not enabled on any interface

These are examples of output from the show auto qos interface interface-id command when auto-QoS is disabled on an interface:

Switch> show auto qos interface gigabitethernet0/1

AutoQoS is disabled

Related Commands

Command	Description
auto qos voip	Automatically configures QoS for VoIP within a QoS domain.
debug auto qos	Enables debugging of the auto-QoS feature.

show boot

Use the show boot privileged EXEC command to display the settings of the boot environment variables.

show boot [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show boot command. Table 2-15 describes each field in the display.

Switch# show boot

BOOT path-list:      flash:c2970-i5q3l2-mz-121.11.AX/c2970-i5q3l2-mz-121.11.AX.binConfig 
file:         flash:config.text

Private Config file: private-config

Enable Break:        no

Manual Boot:         yes

HELPER path-list:

NVRAM/Config file

      buffer size:   32768 

Table 2-15 show boot Field Descriptions

Field	Description
BOOT path-list	Displays a semicolon separated list of executable files to try to load and execute when automatically booting. If the BOOT environment variable is not set, the system attempts to load and execute the first executable image it can find by using a recursive, depth-first search through the flash file system. In a depth-first search of a directory, each encountered subdirectory is completely searched before continuing the search in the original directory. If the BOOT variable is set but the specified images cannot be loaded, the system attempts to boot the first bootable file that it can find in the flash file system.
Config file	Displays the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration.
Private Config file	Displays the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration.
Enable Break	Displays whether a break during booting is enabled or disabled. If it is set to yes, on, or 1, you can interrupt the automatic boot process by pressing the Break key on the console after the flash file system is initialized.
Manual Boot	Displays whether the switch automatically or manually boots. If it is set to no or 0, the boot loader attempts to automatically boot the system. If it is set to anything else, you must manually boot the switch from the boot loader mode.
Helper path-list	Displays a semicolon separated list of loadable files to dynamically load during the boot loader initialization. Helper files extend or patch the functionality of the boot loader.
NVRAM/Config file buffer size	Displays the buffer size that Cisco IOS uses to hold a copy of the configuration file in memory. The configuration file cannot be larger than the buffer size allocation.

Related Commands

Command	Description
boot config-file	Specifies the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration.
boot enable-break	Enables interrupting the automatic boot process.
boot manual	Enables manually booting the switch during the next boot cycle.
boot private-config-file	Specifies the filename that Cisco IOS uses to read and write a nonvolatile copy of the private configuration.
boot system	Specifies the Cisco IOS image to load during the next boot cycle.

show cable-diagnostics tdr

Use the show cable-diagnostics tdr privileged EXEC command to display the Time Domain Reflector (TDR) results.

show cable-diagnostics tdr interface interface-id [ | {begin | exclude | include} expression]

Syntax Description

interface-id	Specify the interface on which TDR was run.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(19)EA1	This command was introduced.

Usage Guidelines

TDR is supported only on copper Ethernet 10/100/1000 ports. It is not supported on 10/100 ports or small form-factor pluggable (SFP)-module ports. For more information about TDR, refer to the software configuration guide for this release.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show cable-diagnostics tdr interface interface-id command:

Switch# show cable-diagnostics tdr interface gigabitethernet0/2

TDR test last run on: March 01 20:15:40

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi0/2   auto  Pair A     0    +/- 2  meters N/A         Open

                Pair B     0    +/- 2  meters N/A         Open

                Pair C     0    +/- 2  meters N/A         Open

                Pair D     0    +/- 2  meters N/A         Open

Table 2-16 lists the descriptions of the fields in the show cable-diagnostics tdr command output.

Table 2-16 Fields Descriptions for the show cable-diagnostics tdr Command Output 

Field	Description
Interface	Interface on which TDR was run.
Speed	Speed of connection.
Local pair	Name of the pair of wires that TDR is testing on the local interface.
Pair length	Location on the cable where the problem is, with respect to your switch. TDR can only find the location in one of these cases: •The cable is properly connected, the link is up, and the interface speed is 1000 Mbps. •The cable is open. •The cable has a short.
Remote pair	Name of the pair of wires to which the local pair is connected. TDR can learn about the remote pair only when the cable is properly connected and the link is up.
Pair status	The status of the pair of wires on which TDR is running: •Normal—The pair of wires is properly connected. •Not completed—The test is running and is not completed. •Not supported—The interface does not support TDR. •Open—The pair of wires is open. •Shorted—The pair of wires is shorted.

For more examples of output from the show cable-diagnostics tdr interface interface-id command, refer to the software configuration guide for this release.

Related Commands

Command	Description
test cable-diagnostics tdr	Enables and runs TDR on an interface.

show class-map

Use the show class-map user EXEC command to display quality of service (QoS) class maps, which define the match criteria to classify traffic.

show class-map [class-map-name] [ | {begin | exclude | include} expression]

Syntax Description

class-map-name	(Optional) Display the contents of the specified class map.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show class-map command:

Switch> show class-map 

Class Map match-all videowizard_10-10-10-10 (id 2)

   Match access-group name videowizard_10-10-10-10

 Class Map match-any class-default (id 0)

   Match any

 Class Map match-all dscp5 (id 3)

   Match ip dscp 5

Related Commands

Command	Description
class-map	Creates a class map to be used for matching packets to the class whose name you specify.
match (class-map configuration)	Defines the match criteria to classify traffic.

show cluster

Use the show cluster user EXEC command to display the cluster status and a summary of the cluster to which the switch belongs. This command can be entered on the cluster command switch and cluster member switches.

show cluster [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

If you enter this command on a switch that is not a cluster member, the error message Not a management cluster member appears.

On a cluster member switch, this command displays the identity of the cluster command switch, the switch member number, and the state of its connectivity with the cluster command switch.

On a cluster command switch, this command displays the cluster name and the total number of members. It also shows the cluster status and time since the status changed. If redundancy is enabled, it displays the primary and secondary command-switch information.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output when the show cluster command is entered on the active cluster command switch:

Switch> show cluster

Command switch for cluster "Ajang"

        Total number of members:        7

        Status:                         1 members are unreachable

        Time since last status change:  0 days, 0 hours, 2 minutes

        Redundancy:                     Enabled

                Standby command switch: Member 1

                Standby Group:          Ajang_standby

                Standby Group Number:   110

        Heartbeat interval:             8

        Heartbeat hold-time:            80

        Extended discovery hop count:   3 

This is an example of output when the show cluster command is entered on a cluster member switch:

Switch1> show cluster

Member switch for cluster "hapuna"

        Member number:                  3

        Management IP address:          192.192.192.192

        Command switch mac address:     0000.0c07.ac14

        Heartbeat interval:             8

        Heartbeat hold-time:            80 

This is an example of output when the show cluster command is entered on a cluster member switch that is configured as the standby cluster command switch:

Switch> show cluster

Member switch for cluster "hapuna"

        Member number:                  3 (Standby command switch)

        Management IP address:          192.192.192.192

        Command switch mac address:     0000.0c07.ac14

        Heartbeat interval:             8

        Heartbeat hold-time:            80 

This is an example of output when the show cluster command is entered on the cluster command switch that has lost connectivity with member 1:

Switch> show cluster

Command switch for cluster "Ajang"

        Total number of members:        7

        Status:                         1 members are unreachable

        Time since last status change:  0 days, 0 hours, 5 minutes

        Redundancy:                     Disabled

        Heartbeat interval:             8

        Heartbeat hold-time:            80

        Extended discovery hop count:   3 

This is an example of output when the show cluster command is entered on a cluster member switch that has lost connectivity with the cluster command switch:

Switch> show cluster

Member switch for cluster "hapuna"

        Member number:                  <UNKNOWN>

        Management IP address:          192.192.192.192

        Command switch mac address:     0000.0c07.ac14

        Heartbeat interval:             8

        Heartbeat hold-time:            80 

Related Commands

Command	Description
cluster enable	Enables a command-capable switch as the cluster command switch, assigns a cluster name, and optionally assigns a member number to it.
show cluster candidates	Displays a list of candidate switches.
show cluster members	Displays information about the cluster members.

show cluster candidates

Use the show cluster candidates privileged EXEC command to display a list of candidate switches.

show cluster candidates [detail | mac-address H.H.H.] [ | {begin | exclude | include} expression]

Syntax Description

detail	(Optional) Display detailed information for all candidates.
mac-address H.H.H.	(Optional) MAC address of the cluster candidate.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

This command is available only on the cluster command switch.

If the switch is not a cluster command switch, the command displays an empty line at the prompt.

The SN in the display means switch member number. If E appears in the SN column, it means that the switch is discovered through extended discovery. If E does not appear in the SN column, it means that the switch member number is the upstream neighbor of the candidate switch. The hop count is the number of devices the candidate is from the cluster command switch.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show cluster candidates command:

Switch> show cluster candidates

                                                             |---Upstream---|

MAC Address    Name         Device Type      PortIf  FEC Hops SN PortIf  FEC

00d0.7961.c4c0 StLouis-2    WS-C2970-12T     Gi0/1      2   1  Fa0/11 

00d0.bbf5.e900 ldf-dist-128 WS-C3524-XL      Fa0/7        1   0  Fa0/24      

00e0.1e7e.be80 1900_Switch  1900             3        0   1   0  Fa0/11      

00e0.1e9f.7a00 Surfers-24   WS-C2924-XL      Fa0/5        1   0  Fa0/3       

00e0.1e9f.8c00 Surfers-12-2 WS-C2912-XL      Fa0/4        1   0  Fa0/7       

00e0.1e9f.8c40 Surfers-12-1 WS-C2912-XL      Fa0/1        1   0  Fa0/9       

This is an example of output from the show cluster candidates command that uses the MAC address of a cluster member switch directly connected to the cluster command switch:

Switch> show cluster candidates mac-address 00d0.7961.c4c0

Device 'Tahiti-12' with mac address number 00d0.7961.c4c0

        Device type:            cisco WS-C2970-12T

        Upstream MAC address:   00d0.796d.2f00 (Cluster Member 0)

        Local port:             Gi0/1   FEC number:

        Upstream port:          GI0/11  FEC Number:

Hops from cluster edge: 1

        Hops from command device: 1

This is an example of output from the show cluster candidates command that uses the MAC address of a cluster member switch three hops from the cluster edge:

Switch> show cluster candidates mac-address 0010.7bb6.1cc0

Device 'Ventura' with mac address number 0010.7bb6.1cc0

        Device type:            cisco WS-C2912MF-XL

        Upstream MAC address:   0010.7bb6.1cd4

        Local port:             Fa2/1   FEC number: 

        Upstream port:          Fa0/24  FEC Number: 

        Hops from cluster edge: 3

        Hops from command device: -

This is an example of output from the show cluster candidates detail command:

Switch> show cluster candidates detail

Device 'Tahiti-12' with mac address number 00d0.7961.c4c0

        Device type:            cisco WS-C3512-XL

        Upstream MAC address:   00d0.796d.2f00 (Cluster Member 1)

        Local port:             Fa0/3   FEC number: 

        Upstream port:          Fa0/13  FEC Number: 

        Hops from cluster edge: 1

        Hops from command device: 2

Device '1900_Switch' with mac address number 00e0.1e7e.be80

        Device type:            cisco 1900

        Upstream MAC address:   00d0.796d.2f00 (Cluster Member 2)

        Local port:             3       FEC number: 0

        Upstream port:          Fa0/11  FEC Number: 

        Hops from cluster edge: 1

        Hops from command device: 2

Device 'Surfers-24' with mac address number 00e0.1e9f.7a00

        Device type:            cisco WS-C2924-XL

        Upstream MAC address:   00d0.796d.2f00 (Cluster Member 3)

        Local port:             Fa0/5   FEC number: 

        Upstream port:          Fa0/3   FEC Number: 

        Hops from cluster edge: 1

        Hops from command device: 2

Related Commands

Command	Description
show cluster	Displays the cluster status and a summary of the cluster to which the switch belongs.
show cluster members	Displays information about the cluster members.

show cluster members

Use the show cluster members privileged EXEC command to display information about the cluster members.

show cluster members [n | detail] [ | {begin | exclude | include} expression]

Syntax Description

n	(Optional) Number that identifies a cluster member. The range is 0 to 15.
detail	(Optional) Display detailed information for all cluster members.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

This command is available only on the cluster command switch.

If the cluster has no members, this command displays an empty line at the prompt.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show cluster members command. The SN in the display means switch number.

Switch# show cluster members

                                                |---Upstream---|

SN MAC Address    Name         PortIf FEC Hops   SN PortIf  FEC  State

0  0002.4b29.2e00 StLouis1                 0                    Up   (Cmdr)

1  0030.946c.d740 tal-switch-1 Fa0/13      1     0  Gi0/1       Up

2  0002.b922.7180 nms-2820     10      0   2     1  Fa0/18      Up

3  0002.4b29.4400 SanJuan2     Gi0/1       2     1  Fa0/11      Up

4  0002.4b28.c480 GenieTest    Gi0/2       2     1  Fa0/9       Up

This is an example of output from the show cluster members for cluster member 3:

Switch# show cluster members 3

Device 'SanJuan2' with member number 3

        Device type:            cisco WS-C2970-12T

        MAC address:            0002.4b29.4400

        Upstream MAC address:   0030.946c.d740 (Cluster member 1)

        Local port:             Gi0/1   FEC number:

        Upstream port:          GI0/11  FEC Number:

        Hops from command device: 2    

This is an example of output from the show cluster members detail command:

Switch# show cluster members detail

Device 'StLouis1' with member number 0 (Command Switch)

        Device type:            cisco WS-C2970-12T

        MAC address:            0002.4b29.2e00

        Upstream MAC address:

        Local port:                     FEC number:

        Upstream port:                  FEC Number:

        Hops from command device: 0                 

Device 'tal-switch-14' with member number 1

        Device type:            cisco WS-C3548-XL

        MAC address:            0030.946c.d740

        Upstream MAC address:   0002.4b29.2e00 (Cluster member 0)

        Local port:             Fa0/13  FEC number:

        Upstream port:          Gi0/1   FEC Number:

        Hops from command device: 1                   

Device 'nms-2820' with member number 2

        Device type:            cisco 2820

        MAC address:            0002.b922.7180

        Upstream MAC address:   0030.946c.d740 (Cluster member 1)

        Local port:             10      FEC number: 0

        Upstream port:          Fa0/18  FEC Number:

        Hops from command device: 2                        

Device 'SanJuan2' with member number 3

        Device type:            cisco WS-C2970-12T

        MAC address:            0002.4b29.4400

        Upstream MAC address:   0030.946c.d740 (Cluster member 1)

        Local port:             Gi0/1   FEC number:

        Upstream port:          Fa0/11  FEC Number:

        Hops from command device: 2

Device 'GenieTest' with member number 4

        Device type:            cisco SeaHorse

        MAC address:            0002.4b28.c480

        Upstream MAC address:   0030.946c.d740 (Cluster member 1)

        Local port:             Gi0/2   FEC number:

        Upstream port:          Fa0/9   FEC Number:

        Hops from command device: 2

Device 'Palpatine' with member number 5

        Device type:            cisco WS-C2924M-XL

        MAC address:            00b0.6404.f8c0

        Upstream MAC address:   0002.4b29.2e00 (Cluster member 0)

        Local port:             Gi2/1   FEC number:

        Upstream port:          Gi0/7   FEC Number:

        Hops from command device: 1                            

Related Commands

Command	Description
show cluster	Displays the cluster status and a summary of the cluster to which the switch belongs.
show cluster candidates	Displays a list of candidate switches.

show controllers cpu-interface

Use the show controllers cpu-interface privileged EXEC command to display the state of the CPU network interface ASIC and the send and receive statistics for packets reaching the CPU.

show controllers cpu-interface [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

This display provides information that might be useful for Cisco technical support representatives troubleshooting the switch.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is a partial output example from the show controllers cpu-interface command:

Switch# show controllers cpu-interface

cpu-queue-frames  retrieved  dropped    invalid    hol-block

----------------- ---------- ---------- ---------- ----------

rpc               4523063    0          0          0

stp               1545035    0          0          0

ipc               1903047    0          0          0

routing protocol  96145      0          0          0

L2 protocol       79596      0          0          0

remote console    0          0          0          0

sw forwarding     5756       0          0          0

host              225646     0          0          0

broadcast         46472      0          0          0

cbt-to-spt        0          0          0          0

igmp snooping     68411      0          0          0

icmp              0          0          0          0

logging           0          0          0          0

rpf-fail          0          0          0          0

queue14           0          0          0          0

cpu heartbeat     1710501    0          0          0

Supervisor ASIC receive-queue parameters

----------------------------------------

 queue 0 maxrecevsize 5EE pakhead 1419A20 paktail 13EAED4

 queue 1 maxrecevsize 5EE pakhead 15828E0 paktail 157FBFC

 queue 2 maxrecevsize 5EE pakhead 1470D40 paktail 1470FE4

 queue 3 maxrecevsize 5EE pakhead 19CDDD0 paktail 19D02C8

<output truncated>

Supervisor ASIC Mic Registers

------------------------------

MicDirectPollInfo               80000800

MicIndicationsReceived          00000000

MicInterruptsReceived           00000000

MicPcsInfo                      0001001F

MicPlbMasterConfiguration       00000000

MicRxFifosAvailable             00000000

MicRxFifosReady                 0000BFFF

MicTimeOutPeriod:       FrameTOPeriod: 00000EA6 DirectTOPeriod: 00004000

<output truncated>

MicTransmitFifoInfo:

Fifo0:   StartPtrs:     038C2800        ReadPtr:        038C2C38

        WritePtrs:      038C2C38        Fifo_Flag:      8A800800

        Weights:        001E001E

Fifo1:  StartPtr:       03A9BC00        ReadPtr:        03A9BC60

        WritePtrs:      03A9BC60        Fifo_Flag:      89800400

        writeHeaderPtr: 03A9BC60

Fifo2:  StartPtr:       038C8800        ReadPtr:        038C88E0

        WritePtrs:      038C88E0        Fifo_Flag:      88800200

        writeHeaderPtr: 038C88E0

Fifo3:  StartPtr:       03C30400        ReadPtr:        03C30638

        WritePtrs:      03C30638        Fifo_Flag:      89800400

        writeHeaderPtr: 03C30638

Fifo4:  StartPtr:       03AD5000        ReadPtr:        03AD50A0

        WritePtrs:      03AD50A0        Fifo_Flag:      89800400

        writeHeaderPtr: 03AD50A0

Fifo5:  StartPtr:       03A7A600        ReadPtr:        03A7A600

        WritePtrs:      03A7A600        Fifo_Flag:      88800200

        writeHeaderPtr: 03A7A600

Fifo6:  StartPtr:       03BF8400        ReadPtr:        03BF87F0

        WritePtrs:      03BF87F0        Fifo_Flag:      89800400 

<output truncated>

Related Commands

Command	Description
show controllers ethernet-controller	Displays per-interface send and receive statistics read from the hardware or the interface internal registers.
show interfaces	Displays the administrative and operational status of all interfaces or a specified interface.

show controllers ethernet-controller

Use the show controllers ethernet-controller privileged EXEC command without keywords to display per-interface send and receive statistics read from the hardware. Use with the phy keyword to display the interface internal registers or the port-asic keyword to display information about the port ASIC.

show controllers ethernet-controller [interface-id] [phy [detail]] [port-asic {configuration | statistics}] [ | {begin | exclude | include} expression]

Syntax Description

interface-id	The physical interface (including type, module, and port number).
phy	(Optional) Display the status of the internal registers on the switch physical layer device (PHY) for the device or the interface. This display includes the operational state of the automatic medium-dependent interface crossover (Auto-MDIX) feature on an interface.
detail	(Optional) Display details about the PHY internal registers.
port-asic	(Optional) Display information about the port ASIC internal registers.
configuration	Display port ASIC internal register configuration.
statistics	Display port ASIC statistics, including the Rx/Sup Queue and miscellaneous statistics.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC (only supported with the interface-id keywords in user EXEC mode)

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

This display without keywords provides traffic statistics, basically the RMON statistics for all interfaces or for the specified interface.

When you enter the phy or port-asic keywords, the displayed information is useful primarily for Cisco technical support representatives troubleshooting the switch.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show controllers ethernet-controller command for an interface. Table 2-17 describes the Transmit fields, and Table 2-18 describes the Receive fields.

Switch# show controllers ethernet-controller gigabitethernet0/1

Transmit GigabitEthernet0/1            Receive

         0 Bytes                             0 Bytes

         0 Unicast frames                    0 Unicast frames

         0 Multicast frames                  0 Multicast frames

         0 Broadcast frames                  0 Broadcast frames

         0 Too old frames                    0 Unicast bytes

         0 Deferred frames                   0 Multicast bytes

         0 MTU exceeded frames               0 Broadcast bytes

         0 1 collision frames                0 Alignment errors

         0 2 collision frames                0 FCS errors

         0 3 collision frames                0 Oversize frames

         0 4 collision frames                0 Undersize frames

         0 5 collision frames                0 Collision fragments

         0 6 collision frames

         0 7 collision frames                0 Minimum size frames

         0 8 collision frames                0 65 to 127 byte frames

         0 9 collision frames                0 128 to 255 byte frames

         0 10 collision frames               0 256 to 511 byte frames

         0 11 collision frames               0 512 to 1023 byte frames

         0 12 collision frames               0 1024 to 1518 byte frames

         0 13 collision frames               0 Overrun frames

         0 14 collision frames               0 Pause frames

         0 15 collision frames               0 Symbol error frames

         0 Excessive collisions

         0 Late collisions                   0 Invalid frames, too large

         0 VLAN discard frames               0 Valid frames, too large

         0 Excess defer frames               0 Invalid frames, too small

         0 64 byte frames                    0 Valid frames, too small

         0 127 byte frames

         0 255 byte frames                   0 Too old frames

         0 511 byte frames                   0 Valid oversize frames

         0 1023 byte frames                  0 System FCS error frames

         0 1518 byte frames                  0 RxPortFifoFull drop frame

         0 Too large frames

         0 Good (1 coll) frames

Table 2-17 Transmit Field Descriptions 

Field	Description
Bytes	The total number of bytes sent on an interface.
Unicast Frames	The total number of frames sent to unicast addresses.
Multicast frames	The total number of frames sent to multicast addresses.
Broadcast frames	The total number of frames sent to broadcast addresses.
Too old frames	The number of frames dropped on the egress port because the packet aged out.
Deferred frames	The number of frames that are not sent after the time exceeds 2*maximum-packet time.
MTU exceeded frames	The number of frames that are larger than the maximum allowed frame size.
1 collision frames	The number of frames that are successfully sent on an interface after one collision occurs.
2 collision frames	The number of frames that are successfully sent on an interface after two collisions occur.
3 collision frames	The number of frames that are successfully sent on an interface after three collisions occur.
4 collision frames	The number of frames that are successfully sent on an interface after four collisions occur.
5 collision frames	The number of frames that are successfully sent on an interface after five collisions occur.
6 collision frames	The number of frames that are successfully sent on an interface after six collisions occur.
7 collision frames	The number of frames that are successfully sent on an interface after seven collisions occur.
8 collision frames	The number of frames that are successfully sent on an interface after eight collisions occur.
9 collision frames	The number of frames that are successfully sent on an interface after nine collisions occur.
10 collision frames	The number of frames that are successfully sent on an interface after ten collisions occur.
11 collision frames	The number of frames that are successfully sent on an interface after 11 collisions occur.
12 collision frames	The number of frames that are successfully sent on an interface after 12 collisions occur.
13 collision frames	The number of frames that are successfully sent on an interface after 13 collisions occur.
14 collision frames	The number of frames that are successfully sent on an interface after 14 collisions occur.
15 collision frames	The number of frames that are successfully sent on an interface after 15 collisions occur.
Excessive collisions	The number of frames that could not be sent on an interface after 16 collisions occur.
Late collisions	After a frame is sent, the number of frames dropped because late collisions were detected while the frame was sent.
VLAN discard frames	The number of frames dropped on an interface because the CFI1 bit is set.
Excess defer frames	The number of frames that are not sent after the time exceeds the maximum-packet time.
64 byte frames	The total number of frames sent on an interface that are 64 bytes.
127 byte frames	The total number of frames sent on an interface that are from 65 to 127 bytes.
255 byte frames	The total number of frames sent on an interface that are from 128 to 255 bytes.
511 byte frames	The total number of frames sent on an interface that are from 256 to 511 bytes.
1023 byte frames	The total number of frames sent on an interface that are from 512 to 1023 bytes.
1518 byte frames	The total number of frames sent on an interface that are from 1024 to 1518 bytes.
Too large frames	The number of frames sent on an interface that are larger than the maximum allowed frame size.
Good (1 coll) frames	The number of frames that are successfully sent on an interface after one collision occurs. This value does not include the number of frames that are not successfully sent after one collision occurs.

1 CFI = Canonical Format Indicator

Table 2-18 Receive Field Descriptions 

Field	Description
Bytes	The total amount of memory (in bytes) used by frames received on an interface, including the FCS1 value and the incorrectly formed frames. This value excludes the frame header bits.
Unicast frames	The total number of frames successfully received on the interface that are directed to unicast addresses.
Multicast frames	The total number of frames successfully received on the interface that are directed to multicast addresses.
Broadcast frames	The total number of frames successfully received on an interface that are directed to broadcast addresses.
Unicast bytes	The total amount of memory (in bytes) used by unicast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits.
Multicast bytes	The total amount of memory (in bytes) used by multicast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits.
Broadcast bytes	The total amount of memory (in bytes) used by broadcast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits.
Alignment errors	The total number of frames received on an interface that have alignment errors.
FCS errors	The total number of frames received on an interface that have a valid length (in bytes) but do not have the correct FCS values.
Oversize frames	The number of frames received on an interface that are larger than the maximum allowed frame size.
Undersize frames	The number of frames received on an interface that are smaller than 64 bytes.
Collision fragments	The number of collision fragments received on an interface.
Minimum size frames	The total number of frames that are the minimum frame size.
65 to 127 byte frames	The total number of frames that are from 65 to 127 bytes.
128 to 255 byte frames	The total number of frames that are from 128 to 255 bytes.
256 to 511 byte frames	The total number of frames that are from 256 to 511 bytes.
512 to 1023 byte frames	The total number of frames that are from 512 to 1023 bytes.
1024 to 1518 byte frames	The total number of frames that are from 1024 to 1518 bytes.
Overrun frames	The total number of overrun frames received on an interface.
Pause frames	The number of pause frames received on an interface.
Symbol error frames	The number of frames received on an interface that have symbol errors.
Invalid frames, too large	The number of frames received that were larger than maximum allowed MTU2 size (including the FCS bits and excluding the frame header) and that have either an FCS error or an alignment error.
Valid frames, too large	The number of frames received on an interface that are larger than the maximum allowed frame size.
Invalid frames, too small	The number of frames received that are smaller than 64 bytes (including the FCS bits and excluding the frame header) and that have either an FCS error or an alignment error.
Valid frames, too small	The number of frames received on an interface that are smaller than 64 bytes (or 68 bytes for VLAN-tagged frames) and that have valid FCS values. The frame size includes the FCS bits but excludes the frame header bits.
Too old frames	The number of frames dropped on the ingress port because the packet aged out.
Valid oversize frames	The number of frames received on an interface that are larger than the maximum allowed frame size and have valid FCS values. The frame size includes the FCS value but does not include the VLAN tag.
System FCS error frames	The total number of frames received on an interface that have a valid length (in bytes) but that do not have the correct FCS values.
RxPortFifoFull drop frames	The total number of frames received on an interface that are dropped because the ingress queue is full.

1 FCS = frame check sequence 2 MTU = maximum transmission unit

This is an example of output from the show controllers ethernet-controller phy command for a specific interface. Note that the last line of the display is the setting for Auto-MDIX for the interface.

Switch# show controllers ethernet-controller gigabitethernet0/2 phy

Control Register                      :  0001 0001 0100 0000

 Control STATUS                        :  0111 1001 0100 1001

 Phy ID 1                              :  0000 0001 0100 0001

 Phy ID 2                              :  0000 1100 0010 0100

 Auto-Negotiation Advertisement        :  0000 0011 1110 0001

 Auto-Negotiation Link Partner         :  0000 0000 0000 0000

 Auto-Negotiation Expansion Reg        :  0000 0000 0000 0100

 Next Page Transmit Register           :  0010 0000 0000 0001

 Link Partner Next page Registe        :  0000 0000 0000 0000

 1000BASE-T Control Register           :  0000 1111 0000 0000

 1000BASE-T Status Register            :  0100 0000 0000 0000

 Extended Status Register              :  0011 0000 0000 0000

 PHY Specific Control Register         :  0000 0000 0111 1000

 PHY Specific Status Register          :  1000 0001 0100 0000

 Interrupt Enable                      :  0000 0000 0000 0000

 Interrupt Status                      :  0000 0000 0100 0000

 Extended PHY Specific Control         :  0000 1100 0110 1000

 Receive Error Counter                 :  0000 0000 0000 0000

 Reserved Register 1                   :  0000 0000 0000 0000

 Global Status                         :  0000 0000 0000 0000

 LED Control                           :  0100 0001 0000 0000

 Manual LED Override                   :  0000 1000 0010 1010

 Extended PHY Specific Control         :  0000 0000 0001 1010

 Disable Receiver 1                    :  0000 0000 0000 1011

 Disable Receiver 2                    :  1000 0000 0000 0100

 Extended PHY Specific Status          :  1000 0100 1000 0000

 Auto-MDIX                             :  On   [AdminState=1   Flags=0x00052248]

This is an example of output from the show controllers ethernet-controller port-asic configuration command:

Switch# show controllers ethernet-controller port-asic configuration

========================================================================

PortASIC 0 Registers

------------------------------------------------------------------------

DeviceType                         : 000101BC

Reset                              : 00000000

PmadMicConfig                      : 00000001

PmadMicDiag                        : 00000003

SupervisorReceiveFifoSramInfo      : 000007D0 000007D0 40000000

SupervisorTransmitFifoSramInfo     : 000001D0 000001D0 40000000

GlobalStatus                       : 00000800

IndicationStatus                   : 00000000

IndicationStatusMask               : FFFFFFFF

InterruptStatus                    : 00000000

InterruptStatusMask                : 01FFE800

SupervisorDiag                     : 00000000

SupervisorFrameSizeLimit           : 000007C8

SupervisorBroadcast                : 000A0F01

GeneralIO                          : 000003F9 00000000 00000004

StackPcsInfo                       : FFFF1000 860329BD 5555FFFF FFFFFFFF

                                     FF0FFF00 86020000 5555FFFF 00000000

StackRacInfo                       : 73001630 00000003 7F001644 00000003

                                     24140003 FD632B00 18E418E0 FFFFFFFF

StackControlStatus                 : 18E418E0

stackControlStatusMask             : FFFFFFFF

TransmitBufferFreeListInfo         : 00000854 00000800 00000FF8 00000000

                                     0000088A 0000085D 00000FF8 00000000

TransmitRingFifoInfo               : 00000016 00000016 40000000 00000000

                                     0000000C 0000000C 40000000 00000000

TransmitBufferInfo                 : 00012000 00000FFF 00000000 00000030

TransmitBufferCommonCount          : 00000F7A

TransmitBufferCommonCountPeak      : 0000001E

TransmitBufferCommonCommonEmpty    : 000000FF

NetworkActivity                    : 00000000 00000000 00000000 02400000

DroppedStatistics                  : 00000000

FrameLengthDeltaSelect             : 00000001

SneakPortFifoInfo                  : 00000000

MacInfo                            : 0EC0801C 00000001 0EC0801B 00000001

                                     00C0001D 00000001 00C0001E 00000001

<output truncated>

This is an example of output from the show controllers ethernet-controller port-asic statistics command:

Switch# show controllers ethernet-controller port-asic statistics

===========================================================================

 PortASIC 0 Statistics

---------------------------------------------------------------------------

         0 RxQ-0, wt-0 enqueue frames            0 RxQ-0, wt-0 drop frames

   4118966 RxQ-0, wt-1 enqueue frames            0 RxQ-0, wt-1 drop frames

         0 RxQ-0, wt-2 enqueue frames            0 RxQ-0, wt-2 drop frames

         0 RxQ-1, wt-0 enqueue frames            0 RxQ-1, wt-0 drop frames

       296 RxQ-1, wt-1 enqueue frames            0 RxQ-1, wt-1 drop frames

   2836036 RxQ-1, wt-2 enqueue frames            0 RxQ-1, wt-2 drop frames

         0 RxQ-2, wt-0 enqueue frames            0 RxQ-2, wt-0 drop frames

         0 RxQ-2, wt-1 enqueue frames            0 RxQ-2, wt-1 drop frames

    158377 RxQ-2, wt-2 enqueue frames            0 RxQ-2, wt-2 drop frames

         0 RxQ-3, wt-0 enqueue frames            0 RxQ-3, wt-0 drop frames

         0 RxQ-3, wt-1 enqueue frames            0 RxQ-3, wt-1 drop frames

         0 RxQ-3, wt-2 enqueue frames            0 RxQ-3, wt-2 drop frames

        15 TxBufferFull Drop Count               0 Rx Fcs Error Frames

         0 TxBufferFrameDesc BadCrc16            0 Rx Invalid Oversize Frames

         0 TxBuffer Bandwidth Drop Cou           0 Rx Invalid Too Large Frames

         0 TxQueue Bandwidth Drop Coun           0 Rx Invalid Too Large Frames

         0 TxQueue Missed Drop Statist           0 Rx Invalid Too Small Frames

        74 RxBuffer Drop DestIndex Cou           0 Rx Too Old Frames

         0 SneakQueue Drop Count                 0 Tx Too Old Frames

         0 Learning Queue Overflow Fra           0 System Fcs Error Frames

         0 Learning Cam Skip Count

        15 Sup Queue 0 Drop Frames               0 Sup Queue 8 Drop Frames

         0 Sup Queue 1 Drop Frames               0 Sup Queue 9 Drop Frames

         0 Sup Queue 2 Drop Frames               0 Sup Queue 10 Drop Frames

         0 Sup Queue 3 Drop Frames               0 Sup Queue 11 Drop Frames

         0 Sup Queue 4 Drop Frames               0 Sup Queue 12 Drop Frames

         0 Sup Queue 5 Drop Frames               0 Sup Queue 13 Drop Frames

         0 Sup Queue 6 Drop Frames               0 Sup Queue 14 Drop Frames

         0 Sup Queue 7 Drop Frames               0 Sup Queue 15 Drop Frames

===========================================================================

 PortASIC 1 Statistics

---------------------------------------------------------------------------

         0 RxQ-0, wt-0 enqueue frames            0 RxQ-0, wt-0 drop frames

        52 RxQ-0, wt-1 enqueue frames            0 RxQ-0, wt-1 drop frames

         0 RxQ-0, wt-2 enqueue frames            0 RxQ-0, wt-2 drop frames

<output truncated>

Related Commands

Command	Description
show boot	Displays the state of the CPU network ASIC and send and receive statistics for packets reaching the CPU.
show controllers tcam	Displays the state of registers for all ternary content addressable memory (TCAM) in the system and for TCAM interface ASICs that are CAM controllers.

show controllers tcam

Use the show controllers tcam privileged EXEC command to display the state of the registers for all ternary content addressable memory (TCAM) in the system and for all TCAM interface ASICs that are CAM controllers.

show controllers tcam [asic [number]] [detail] [ | {begin | exclude | include} expression]

Syntax Description

asic	(Optional) Display port ASIC TCAM information.
number	(Optional) Display information for the specified port ASIC number. The range is from 0 to 15.
detail	(Optional) Display detailed TCAM register information.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(14)EA1	The asic [number] keywords were added.

Usage Guidelines

This display provides information that might be useful for Cisco technical support representatives troubleshooting the switch.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show controllers tcam command:

Switch# show controllers tcam

------------------------------------------------------------------------

TCAM-0 Registers

------------------------------------------------------------------------

  REV:    00B30103

  SIZE:   00080040

  ID:     00000000

  CCR:    00000000_F0000020

  RPID0:  00000000_00000000

  RPID1:  00000000_00000000

  RPID2:  00000000_00000000

  RPID3:  00000000_00000000

  HRR0:   00000000_E000CAFC

  HRR1:   00000000_00000000

  HRR2:   00000000_00000000

  HRR3:   00000000_00000000

  HRR4:   00000000_00000000

  HRR5:   00000000_00000000

  HRR6:   00000000_00000000

  HRR7:   00000000_00000000

<output truncated>

  GMR31:  FF_FFFFFFFF_FFFFFFFF

  GMR32:  FF_FFFFFFFF_FFFFFFFF

  GMR33:  FF_FFFFFFFF_FFFFFFFF

=============================================================================

 TCAM related PortASIC 1 registers

=============================================================================

LookupType:                   89A1C67D_24E35F00

LastCamIndex:                 0000FFE0

LocalNoMatch:                 000069E0

ForwardingRamBaseAddress:

                              00022A00 0002FE00 00040600 0002FE00 0000D400

                              00000000 003FBA00 00009000 00009000 00040600

                              00000000 00012800 00012900

Related Commands

Command	Description
show controllers cpu-interface	Displays the state of the CPU network ASIC and send and receive statistics for packets reaching the CPU.
show controllers ethernet-controller	Displays per-interface send and receive statistics read from the hardware or the interface internal registers.

show dot1x

Use the show dot1x privileged EXEC command to display 802.1x statistics, administrative status, and operational status for the switch or for the specified port.

show dot1x [all | interface interface-id | statistics interface interface-id] [ | {begin | exclude | include} expression]

Syntax Description

all	(Optional) Display the 802.1x status for all ports.
interface interface-id	(Optional) Display the 802.1x status for the specified port (including type, module, and port number).
statistics interface interface-id	(Optional) Display 802.1x statistics for the specified port (including type, module, and port number).
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(14)EA1	The all keyword was added.

Usage Guidelines

If you do not specify a port, global parameters and a summary appear. If you specify a port, details for that port appear.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output appear.

Examples

This is an example of output from the show dot1x and the show dot1x all privileged EXEC commands:

Switch# show dot1x 

Sysauthcontrol                    = Enabled 

Dot1x Protocol Version            = 1 

Dot1x Oper Controlled Directions  = Both 

Dot1x Admin Controlled Directions = Both 

Switch# show dot1x all

Dot1x Info for interface GigabitEthernet0/1 

----------------------------------------------------

Supplicant MAC 00d0.b71b.35de

   AuthSM State      = CONNECTING

   BendSM State      = IDLE

PortStatus        = UNAUTHORIZED

MaxReq            = 2 

HostMode          = Single 

Port Control      = Auto

QuietPeriod       = 60 Seconds 

Re-authentication = Disabled 

ReAuthPeriod      = 3600 Seconds

ServerTimeout     = 30 Seconds 

SuppTimeout       = 30 Seconds 

TxPeriod          = 30 Seconds 

Guest-Vlan        = 0 

Dot1x Info for interface GigabitEthernet0/2 

----------------------------------------------------

PortStatus        = UNAUTHORIZED

MaxReq            = 2 

HostMode          = Multi 

Port Control      = Auto

QuietPeriod       = 60 Seconds 

Re-authentication = Disabled 

ReAuthPeriod      = 3600 Seconds

ServerTimeout     = 30 Seconds 

SuppTimeout       = 30 Seconds 

TxPeriod          = 30 Seconds 

Guest-Vlan        = 0 

This is an example of output from the show dot1x interface interface-id privileged EXEC command:

Switch# show dot1x interface gigabitethernet0/1

Supplicant MAC 00d0.b71b.35de

   AuthSM State      = AUTHENTICATED

   BendSM State      = IDLE

PortStatus        = AUTHORIZED

MaxReq            = 2 

HostMode          = Single 

Port Control      = Auto

QuietPeriod       = 60 Seconds 

Re-authentication = Disabled 

ReAuthPeriod      = 3600 Seconds

ServerTimeout     = 30 Seconds 

SuppTimeout       = 30 Seconds 

TxPeriod          = 30 Seconds 

Guest-Vlan        = 0 

This is an example of output from the show dot1x statistics interface interface-id command. Table 2-19 describes the fields in the display.

Switch# show dot1x statistics interface gigabitethernet0/1

PortStatistics Parameters for Dot1x 

--------------------------------------------

TxReqId = 15    TxReq = 0       TxTotal = 15 

RxStart = 4     RxLogoff = 0    RxRespId = 1    RxResp = 1

RxInvalid = 0   RxLenErr = 0    RxTotal= 6

RxVersion = 1   LastRxSrcMac 00d0.b71b.35de 

Table 2-19 show dot1x statistics Field Descriptions 

Field	Description
TxReqId	Number of Extensible Authentication Protocol (EAP)-request/identity frames that have been sent.
TxReq	Number of EAP-request frames (other than request/identity frames) that have been sent.
TxTotal	Number of Extensible Authentication Protocol over LAN (EAPOL) frames of any type that have been sent.
RxStart	Number of valid EAPOL-start frames that have been received.
RxLogoff	Number of EAPOL-logoff frames that have been received.
RxRespId	Number of EAP-response/identity frames that have been received.
RxResp	Number of valid EAP-response frames (other than response/identity frames) that have been received.
RxInvalid	Number of EAPOL frames that have been received and have an unrecognized frame type.
RxLenError	Number of EAPOL frames that have been received in which the packet body length field is invalid.
RxTotal	Number of valid EAPOL frames of any type that have been received.
RxVersion	Number of received packets in the 802.1x Version 1 format.
LastRxSrcMac	Source MAC address carried in the most recently received EAPOL frame.

Related Commands

Command	Description
dot1x default	Resets the configurable 802.1x parameters to their default values.

show dtp

Use the show dtp privileged EXEC command to display Dynamic Trunking Protocol (DTP) information for the switch or for a specified interface.

show dtp [interface interface-id] [ | {begin | exclude | include} expression]

Syntax Description

interface interface-id	(Optional) Display port security settings for the specified interface. Valid interfaces include physical ports (including type, module, and port number).
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show dtp command:

Switch# show dtp

Global DTP information

        Sending DTP Hello packets every 30 seconds

        Dynamic Trunk timeout is 300 seconds

        21 interfaces using DTP

This is an example of output from the show dtp interface command:

Switch# show dtp interface gigabitethernet0/1

DTP information for GigabitEthernet0/1:

  TOS/TAS/TNS:                              ACCESS/AUTO/ACCESS

  TOT/TAT/TNT:                              NATIVE/NEGOTIATE/NATIVE

  Neighbor address 1:                       000943A7D081

  Neighbor address 2:                       000000000000

  Hello timer expiration (sec/state):       1/RUNNING

  Access timer expiration (sec/state):      never/STOPPED

  Negotiation timer expiration (sec/state): never/STOPPED

  Multidrop timer expiration (sec/state):   never/STOPPED

  FSM state:                                S2:ACCESS

  # times multi & trunk                     0

  Enabled:                                  yes

  In STP:                                   no

  Statistics

  ----------

  3160 packets received (3160 good)

  0 packets dropped

      0 nonegotiate, 0 bad version, 0 domain mismatches, 0 bad TLVs, 0 other

  6320 packets output (6320 good)

      3160 native, 3160 software encap isl, 0 isl hardware native

  0 output errors

  0 trunk timeouts

  1 link ups, last link up on Mon Mar 01 1993, 01:02:29

  0 link downs

Related Commands

Command	Description
show interfaces trunk	Displays interface trunking information.

show env

Use the show env user EXEC command to display fan, temperature, redundant power system (RPS) availability, and power information for the switch.

show env {all | fan | power | rps| temperature} [ | {begin | exclude | include} expression]

Syntax Description

all	Display both fan and temperature environmental status.
fan	Display the switch fan status.
power	Display the switch power status.
rps	Display whether an RPS 300 Redundant Power System is connected to the switch.
temperature	Display the switch temperature status.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show env all command entered:

Switch> show env all

FAN is OK

TEMPERATURE is OK

POWER is OK

RPS is AVAILABLE

This is an example of output from the show env fan command:

Switch> show env fan

FAN is OK

show errdisable detect

Use the show errdisable detect user EXEC command to display error-disable detection status.

show errdisable detect [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

A displayed gbic-invalid error reason refers to an invalid small form-factor pluggable (SFP) module.

Examples

This is an example of output from the show errdisable detect command:

Switch> show errdisable detect

ErrDisable Reason    Detection status

-----------------    ----------------

udld                 Enabled

bpduguard            Enabled

security-violatio    Enabled

channel-misconfig    Enabled

psecure-violation    Enabled

vmps                 Enabled

loopback             Enabled

pagp-flap            Enabled

dtp-flap             Enabled

link-flap            Enabled

gbic-invalid         Enabled

dhcp-rate-limit      Enabled

unicast-flood        Enabled

storm-control        Enabled

ilpower              Enabled

---

Note Though visible in the output, the ilpower, storm-control, and unicast-flood fields are not valid.

---

Related Commands

Command	Description
errdisable detect cause	Enables error-disable detection for a specific cause or all causes.
show errdisable flap-values	Displays error condition recognition information.
show errdisable recovery	Displays error-disable recovery timer information.
show interfaces status	Displays interface status or a list of interfaces in error-disabled state.

show errdisable flap-values

Use the show errdisable flap-values user EXEC command to display conditions that cause an error to be recognized for a cause.

show errdisable flap-values [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

The Flaps column in the display shows how many changes to the state within the specified time interval will cause an error to be detected and a port to be disabled. For example, the display shows that an error will be assumed and the port shut down if three Dynamic Trunking Protocol (DTP)-state (port mode access/trunk) or Port Aggregation Protocol (PAgP) flap changes occur during a 30-second interval, or if 5 link-state (link up/down) changes occur during a 10-second interval.

ErrDisable Reason    Flaps    Time (sec)

-----------------    ------   ----------

pagp-flap              3       30

dtp-flap               3       30

link-flap              5       10

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show errdisable flap-values command:

Switch> show errdisable flap-values

ErrDisable Reason    Flaps    Time (sec)

-----------------    ------   ----------

pagp-flap              3       30

dtp-flap               3       30

link-flap              5       10

Related Commands

Command	Description
errdisable detect cause	Enables error-disable detection for a specific cause or all causes.
show errdisable detect	Displays error-disable detection status.
show errdisable recovery	Displays error-disable recovery timer information.
show interfaces status	Displays interface status or a list of interfaces in error-disabled state.

show errdisable recovery

Use the show errdisable recovery user EXEC command to display the error-disable recovery timer information.

show errdisable recovery [ | {begin | exclude | include} expression]

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

A gbic-invalid error-disable reason refers to an invalid small form-factor pluggable (SFP) interface.

Examples

This is an example of output from the show errdisable recovery command:

Switch> show errdisable recovery

ErrDisable Reason    Timer Status

-----------------    --------------

udld                 Disabled

bpduguard            Disabled

security-violatio    Disabled

channel-misconfig    Disabled

vmps                 Disabled

pagp-flap            Disabled

dtp-flap             Disabled

link-flap            Enabled

psecure-violation    Disabled

gbic-invalid         Disabled

dhcp-rate-limit      Disabled

unicast-flood        Disabled

storm-control        Disabled

loopback             Disabled

Timer interval:300 seconds

Interfaces that will be enabled at the next timeout:

Interface    Errdisable reason    Time left(sec)

---------    -----------------    --------------

Gi0/2       link-flap             279 

---

Note Though visible in the output, the unicast-flood field is not valid.

---

Related Commands

Command	Description
errdisable recovery	Configures the recover mechanism variables.
show errdisable detect	Displays error disable detection status.
show errdisable flap-values	Displays error condition recognition information.
show interfaces status	Displays interface status or a list of interfaces in error-disabled state.

show etherchannel

Use the show etherchannel user EXEC command to display EtherChannel information for a channel.

show etherchannel [channel-group-number {detail | port | port-channel | protocol | summary}] {detail | load-balance | port | port-channel | protocol | summary} [ | {begin | exclude | include} expression]

Syntax Description

channel-group-number	(Optional) Number of the channel group. The range is 1 to 12.
detail	Display detailed EtherChannel information.
load-balance	Display the load-balance or frame-distribution scheme among ports in the port channel.
port	Display EtherChannel port information.
port-channel	Display port-channel information.
protocol	Display the protocol that is being used in the EtherChannel.
summary	Display a one-line summary per channel-group.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(14)EA1	The protocol keyword was added.

Usage Guidelines

If you do not specify a channel-group, all channel groups are displayed.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show etherchannel 1 detail command:

Switch> show etherchannel 1 detail

Group state = L2

Ports: 2   Maxports = 16

Port-channels: 1 Max Port-channels = 16

Protocol:   LACP

                Ports in the group:

                -------------------

Port: Gi0/1

------------

Port state    = Up Mstr In-Bndl

Channel group = 1           Mode = Active      Gcchange = -

Port-channel  = Po1         GC   =   -         Pseudo port-channel = Po1

Port index    = 0           Load = 0x00        Protocol =   LACP

Flags:  S - Device is sending Slow LACPDUs   F - Device is sending fast LACPDU

        A - Device is in active mode.        P - Device is in passive mode.

Local information:

                            LACP port     Admin     Oper    Port     Port

Port      Flags   State     Priority      Key       Key     Number   State

Gi0/1     SA      bndl      32768         0x0       0x1     0x0      0x3D

Age of the port in the current state: 01d:20h:06m:04s

                Port-channels in the group:

                ----------------------

Port-channel: Po1    (Primary Aggregator)

------------

Age of the Port-channel   = 01d:20h:20m:26s

Logical slot/port   = 10/1          Number of ports = 2

HotStandBy port = null

Port state          = Port-channel Ag-Inuse

Protocol            =   LACP

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits

------+------+------+------------------+-----------

  0     00     Gi0/1    Active          0

  0     00     Gi0/2    Active          0

Time since last port bundled:    01d:20h:20m:20s    Gi0/2

This is an example of output from the show etherchannel 1 summary command:

Switch> show etherchannel 1 summary

Flags:  D - down        P - in port-channel

        I - stand-alone s - suspended

        H - Hot-standby (LACP only)

        R - Layer3      S - Layer2

        u - unsuitable for bundling

        U - in use      f - failed to allocate aggregator

        d - default port

Number of channel-groups in use: 1

Number of aggregators:           1

Group  Port-channel  Protocol    Ports

------+-------------+-----------+----------------------------------------

1      Po1(SU)         LACP      Gi0/1(P)    Gi0/2(P) 

This is an example of output from the show etherchannel 1 port-channel command:

Switch> show etherchannel 1 port-channel 

                Port-channels in the group: 

                ----------------------

Port-channel: Po1    (Primary Aggregator)

------------

Age of the Port-channel   = 01d:20h:24m:50s

Logical slot/port   = 10/1          Number of ports = 2

HotStandBy port = null

Port state          = Port-channel Ag-Inuse

Protocol            =   LACP

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits

------+------+------+------------------+-----------

  0     00     Gi0/1    Active          0

  0     00     Gi0/2    Active          0

Time since last port bundled:    01d:20h:24m:44s    Gi0/2

This is an example of output from show etherchannel protocol command:

Switch# show etherchannel protocol

                Channel-group listing:

                -----------------------

Group: 1

----------

Protocol:  LACP

Group: 2

----------

Protocol:  PAgP

Related Commands

Command	Description
channel-group	Assigns an Ethernet port to an EtherChannel group.
channel-protocol	Restricts the protocol used on a port to manage channeling.
interface port-channel	Accesses or creates the port channel.

show flowcontrol

Use the show flowcontrol user EXEC command to display the flow control status and statistics.

show flowcontrol [interface interface-id | module number] [ | {begin | exclude | include} expression]

Syntax Description

interface interface-id	(Optional) Display the flow control status and statistics for a specific interface.
module number	(Optional) Display the flow control status and statistics for all interfaces on the switch. The only valid module number is 1.This option is not available if you have entered a specific interface ID.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(14)EA1	This command was introduced.

Usage Guidelines

Use this command to display the flow control status and statistics on the switch or for a specific interface.

Use the show flowcontrol command to display information about all the switch interfaces. The output from the show flowcontrol command is the same as the output from the show flowcontrol module number command.

Use the show flowcontrol interface interface-id command to display information about a specific interface.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show flowcontrol command.

Switch> show flowcontrol

Port       Send FlowControl  Receive FlowControl  RxPause TxPause

           admin    oper     admin    oper

---------  -------- -------- -------- --------    ------- -------

Gi0/1      Unsupp.  Unsupp.  off      off         0       0

Gi0/2      desired  off      off      off         0       0

<output truncated>

This is an example of output from the show flowcontrol interface interface-id command:

Switch> show flowcontrol gigabitethernet0/2

Port       Send FlowControl  Receive FlowControl  RxPause TxPause

           admin    oper     admin    oper

---------  -------- -------- -------- --------    ------- -------

Gi0/2      desired  off      off      off         0       0

Related Commands

Command	Description
flowcontrol	Sets the receive flow-control state for an interface.

show interfaces

Use the show interfaces privileged EXEC command to display the administrative and operational status of all interfaces or a specified interface.

show interfaces [interface-id | vlan vlan-id] [accounting | capabilities [module number] | counters | description | etherchannel | flowcontrol | pruning | stats | status [err-disabled] | switchport [backup | module number] | transceiver [calibration | properties | detail] [module number] | trunk] [ | {begin | exclude | include} expression

Syntax Description

interface-id	(Optional) Valid interfaces include physical ports (including type, module, and port number) and port channels. The valid port-channel range is 1 to 12.
vlan vlan-id	(Optional) VLAN identification. The range is 1 to 4094.
accounting	(Optional) Display accounting information on the interface, including active protocols and input and output packets and octets.
capabilities	(Optional) Display the capabilities of all interfaces or the specified interface, including the features and options that you can configure on the interface. Though visible in the command line help, this option is not available for VLAN IDs.
module number	(Optional) Display capabilities, switchport configuration, or transceiver characteristics (depending on preceding keyword) of all interfaces on the switch.The only valid module number is 1.This option is not available if you have entered a specific interface ID.
counters	(Optional) See the show interfaces counters command.
description	(Optional) Display the administrative status and description set for an interface.
etherchannel	(Optional) Display interface EtherChannel information.
flowcontrol	(Optional) Display interface flowcontrol information
pruning	(Optional) Display interface trunk VTP pruning information.
stats	(Optional) Display the input and output packets by switching path for the interface.
status	(Optional) Display the status of the interface.
err-disabled	(Optional) Display interfaces in error-disabled state.
switchport	(Optional) Display the administrative and operational status of a switching port, including port blocking and port protection settings.
backup	(Optional) Display Flex Link backup interface configuration and status for the specified interface or all interfaces on the switch.
transceiver	(Optional) Display the physical properties of a CWDM1 or DWDM2 small form-factor (SFP) module interface.
calibration	(Optional) Display temperature, voltage, or amount of current on the interface.
detail	(Optional) Display calibration properties, including high and low numbers and any alarm information.
properties	(Optional) Display speed and duplex settings on the interface.
trunk	Display interface trunk information. If you do not specify an interface, only information for active trunking ports is displayed.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

1 Coarse Wave Division Multiplexer 2 Dense Wave Division Multiplexer

---

Note Though visible in the command-line help strings, the crb, fair-queue, irb, mac-accounting, precedence, random-detect, rate-limit, and shape keywords are not supported.

---

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(14)EA1	Support for the capabilities keyword was added.
12.2(20)SE	The backup, transceiver calibration, detail, and properties, keywords were added.

Usage Guidelines

The show interfaces capabilities command with different keywords has these results:

•Use the show interface capabilities module 1 to display the capabilities of all interfaces on the switch. Entering any other number is invalid.

•Use the show interfaces interface-id capabilities to display the capabilities of the specified interface.

•Use the show interfaces capabilities (with no module number or interface ID) to display the capabilities of all interfaces on the switch.

•Use the show interface switchport module 1 to display the switch port characteristics of all interfaces on the switch. Entering any other number is invalid.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of output from the show interfaces command for an interface:

Switch# show interfaces gigabitethernet0/2 

GigabitEthernet0/2 is down, line protocol is down

  Hardware is Gigabit Ethernet, address is 0009.43a7.d085 (bia 0009.43a7.d085)

  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Auto-duplex, Auto-speed

  input flow-control is off, output flow-control is off

  ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue :0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     2 packets input, 1040 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast, 0 pause input

     0 input packets with dribble condition detected

     4 packets output, 1040 bytes, 0 underruns

     0 output errors, 0 collisions, 3 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 PAUSE output

     0 output buffer failures, 0 output buffers swapped out

This is an example of output from the show interfaces accounting command.

Switch# show interfaces accounting

Vlan1

                Protocol    Pkts In   Chars In   Pkts Out  Chars Out

                      IP    1094395  131900022     559555   84077157

           Spanning Tree     283896   17033760         42       2520

                     ARP      63738    3825680        231      13860

Interface Vlan2 is disabled

Vlan7

                Protocol    Pkts In   Chars In   Pkts Out  Chars Out

No traffic sent or received on this interface.

Vlan31

                Protocol    Pkts In   Chars In   Pkts Out  Chars Out

No traffic sent or received on this interface.

GigabitEthernet0/1

                Protocol    Pkts In   Chars In   Pkts Out  Chars Out

No traffic sent or received on this interface.

GigabitEthernet0/2

                Protocol    Pkts In   Chars In   Pkts Out  Chars Out

No traffic sent or received on this interface.

<output truncated>

This is an example of output from the show interfaces capabilities command for an interface.

Switch# show interfaces gigabitethernet0/2 capabilities

GigabitEthernet0/2

  Model:                 WS-C2970G-24T-E

  Type:                  10/100/1000BaseTX

  Speed:                 10,100,1000,auto

  Duplex:                full,auto

  Trunk encap. type:     802.1Q,ISL

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off,on,desired),tx-(none)

  Fast Start:            yes

  QoS scheduling:        rx-(not configurable on per port basis),tx-(4q2t)

  CoS rewrite:           yes

  ToS rewrite:           yes

  UDLD:                  yes

  Inline power:          no

  SPAN:                  source/destination

  PortSecure:            yes

  Dot1x:                 yes

  Dot1x:                 yes

This is an example of output from the show interfaces interface description command when the interface has been described as Connects to Marketing by using the description interface configuration command.

Switch# show interfaces gigabitethernet0/2 description

Interface Status         Protocol Description

Gi0/2       up             down     Connects to Marketing

This is an example of output from the show interfaces etherchannel command when port channels are configured on the switch:

Switch# show interfaces etherchannel

----

Port-channel1:

Age of the Port-channel   = 03d:20h:17m:29s

Logical slot/port   = 10/1           Number of ports = 0

GC                  = 0x00000000      HotStandBy port = null

Port state          = Port-channel Ag-Not-Inuse

Port-channel2:

Age of the Port-channel   = 03d:20h:17m:29s

Logical slot/port   = 10/2           Number of ports = 0

GC                  = 0x00000000      HotStandBy port = null

Port state          = Port-channel Ag-Not-Inuse

Port-channel3:

Age of the Port-channel   = 03d:20h:17m:29s

Logical slot/port   = 10/3           Number of ports = 0

GC                  = 0x00000000      HotStandBy port = null

Port state          = Port-channel Ag-Not-Inuse

This is an example of output from the show interfaces interface-id pruning command when pruning is enabled in the VTP domain:

Switch# show interfaces gigibitethernet0/2 pruning

Port    Vlans pruned for lack of request by neighbor

Gi0/2     3,4

Port    Vlans traffic requested of neighbor

Gi0/2     1-3

This is an example of output from the show interfaces stats command for a specified VLAN interface.

Switch# show interfaces vlan 1 stats

Switching path    Pkts In   Chars In   Pkts Out  Chars Out

        Processor    1165354  136205310     570800   91731594

      Route cache          0          0          0          0

            Total    1165354  136205310     570800   91731594

This is an example of partial output from the show interfaces status command. It displays the status of all interfaces.

Switch# show interfaces status

10/100/1000BaseTX

10/100/1000BaseTXPort      Name               Status       Vlan       Duplex  Speed Type

Gi0/1                        notconnect   1            auto   auto 10/100/1000BaseTX

Gi0/2                        notconnect   1            auto   auto 10/100/1000BaseTX

Gi0/3                        notconnect   1            auto   auto 10/100/1000BaseTX

Gi0/4                        notconnect   1            auto   auto 10/100/1000BaseTX

Gi0/5                        notconnect   1            auto   auto 10/100/1000BaseTX

Gi0/6                        notconnect   1            auto   auto 10/100/1000BaseTX

<output truncated>

This is an example of output from the show interfaces status err-disabled command. It 
displays the status of interfaces in the error-disabled state.

Switch# show interfaces status err-disabled 

Port      Name               Status       Reason

Gi0/2                        err-disabled dtp-flap

This is an example of output from the show interfaces switchport command for a single port. Table 2-20 describes the fields in the display.

---

Note Private VLANs are not supported in this release, so those fields are not applicable.

---

Switch# show interfaces gigabitethernet0/1 switchport

Name: Gi0/1

Switchport: Enabled

Administrative Mode: dynamic auto

Operational Mode: static access

Administrative Trunking Encapsulation: negotiate

Operational Trunking Encapsulation: native

Negotiation of Trunking: On

Access Mode VLAN: 1 (default)

Trunking Native Mode VLAN: 1 (default)

Voice VLAN: none

Administrative private-vlan host-association:10 (VLAN0010) 502 (VLAN0502)

Administrative private-vlan mapping: none 

Administrative private-vlan trunk native VLAN: none

Administrative private-vlan trunk encapsulation: dot1q

Administrative private-vlan trunk normal VLANs: none

Administrative private-vlan trunk private VLANs: none

Operational private-vlan: none

Trunking VLANs Enabled: ALL

Pruning VLANs Enabled: 2-1001

Capture Mode Disabled

Capture VLANs Allowed: ALL

Protected: false

Unknown unicast blocked: disabled

Unknown multicast blocked: disabled

Voice VLAN: none (Inactive)

Appliance trust: none

Table 2-20 show interfaces switchport Field Descriptions 

Field	Description
Name	Displays the port name.
Switchport	Displays the administrative and operational status of the port. In this display, the port is in switchport mode.
Administrative Mode Operational Mode	Displays the administrative and operational modes.
Administrative Trunking Encapsulation Operational Trunking Encapsulation Negotiation of Trunking	Displays the administrative and operational encapsulation method and whether trunking negotiation is enabled.
Access Mode VLAN	Displays the VLAN ID to which the port is configured.
Trunking Native Mode VLAN Trunking VLANs Enabled Trunking VLANs Active	Lists the VLAN ID of the trunk that is in native mode. Lists the allowed VLANs on the trunk. Lists the active VLANs on the trunk.
Pruning VLANs Enabled	Lists the VLANs that are pruning-eligible.
Protected	Displays whether or not protected port is enabled (True) or disabled (False) on the interface.
Unknown unicast blocked Unknown multicast blocked	Displays whether or not unknown multicast and unknown unicast traffic is blocked on the interface.
Voice VLAN	Displays the VLAN ID on which voice VLAN is enabled.
Appliance trust	Displays the class of service (CoS) setting of the data packets of the IP phone.

This is an example of output from the show interfaces switchport backup command:

Switch# show interface switchport backup

Switch Backup Interface Pairs:

     Active Interface    Backup Interface    State

     --------------------------------------------------------------

     Fa0/1             Fa0/2             Active Up/Backup Standby

     Fa0/3             Fa0/5             Active Down/Backup Up

     Po1                 Po2                 Active Standby/Backup Up

Switch# show interfaces gigibitethernet0/2 pruning

Port    Vlans pruned for lack of request by neighbor

This is an example of output from the show interfaces interface-id trunk command. It displays trunking information for the port.

Switch# show interfaces gigabitethernet0/1 trunk

Port          Mode         Encapsulation  Status        Native vlan

Gi0/1         auto         negotiate      trunking      1

Port          Vlans allowed on trunk

Gi0/1         1-4094

Port          Vlans allowed and active in management domain

Gi0/1         1-4

Port          Vlans in spanning tree forwarding state and not pruned

Gi0/1         1-4

This is an example of output from the show interfaces command using the transceiver, calibration, and module number keywords:

Switch# show interfaces transceiver calibration module 2

C:Celsius, V:volts, mA:milliamperes, mW:milliwatts, RX:receive.

             Temperature            Voltage              Current

Port         Slope/Offset(C)      Slope/Offset(V)      Slope/Offset(mA)

-------     ------------------- ------------------- --------------------

Gi0/3       1.0000/   0.0000     1.0000/ 0.0000       1.0000/   0.000

            Transmit Power                      Receive Power

Port         Slope/Offset(mW) RX_POWER4/RX_POWER3/RX_POWER2/RX_POWER1/RX_POWER0

-------     -------------------- -------------------------------------------------

Gi0/3

This is an example of output from the show interfaces command using the module number, transceiver, and detail keywords:

Switch# show interfaces gigabitethernet0/3 transceiver detail

ITU Channel not available (Wavelength not available),

Transceiver is externally calibrated.

mA:milliamperes, dBm:decibels (milliwatts), N/A:not applicable.

++:high alarm, +:high warning, -:low warning, -- :low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are uncalibrated.

                            High Alarm  High Warn  Low Warn   Low Alarm

        Temperature         Threshold   Threshold  Threshold  Threshold

Port     (Celsius)          (Celsius)   (Celsius)  (Celsius)  (Celsius)

------- ------------------  ----------  ---------  ---------  ---------

Gi0/3   41.5               110.0       103.0        -8.0      -12.0

                            High Alarm  High Warn  Low Warn   Low Alarm

         Voltage            Threshold   Threshold  Threshold  Threshold

Port     (Volts)            (Volts)     (Volts)    (Volts)    (Volts)

-------  ---------------    ----------  ---------  ---------  ---------

Gi0/3    3.20                  4.00        3.70        3.00       2.95

                            High Alarm  High Warn  Low Warn   Low Alarm

         Current            Threshold   Threshold  Threshold  Threshold

Port     (milliamperes)     (mA)        (mA)       (mA)       (mA)

-------  -----------------  ----------  ---------  ---------  ---------

Gi0/3   31.0                84.0        70.0         4.0        2.0

         Optical            High Alarm  High Warn  Low Warn   Low Alarm

         Transmit Power     Threshold   Threshold  Threshold  Threshold

Port     (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------  -----------------  ----------  ---------  ---------  ---------

Gi0/3     -0.0 ( -0.0)        -0.0        -0.0        -0.0       -0.0

         Optical            High Alarm  High Warn  Low Warn   Low Alarm

         Receive Power      Threshold   Threshold  Threshold  Threshold

Port     (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------  -----------------  ----------  ---------  ---------  ---------

Gi0/3     N/A  ( -0.0) --     -0.0        -0.0        -0.0       -0.0

This is an example of output from the show interfaces command using the module number, transceiver and properties keywords:

Switch# show interfaces gigabitethernet0/3 transceiver properties

Name :Gi0/3

Administrative Speed:auto

Operational Speed:auto

Administrative Duplex:auto

Operational Duplex:auto

Administrative Auto-MDIX:on

Operational Auto-MDIX:on

ITU Channel not available (Wavelength not available),

Transceiver is externally calibrated.

Related Commands

Command	Description
switchport access	Configures a port as a static-access or a dynamic-access port.
switchport block	Blocks unknown unicast or multicast traffic on an interface.
switchport backup interface	Configures Flex Links, a pair of Layer 2 interfaces that provide mutual backup.
switchport mode	Configures the VLAN membership mode of a port.
switchport protected	Isolates unicast, multicast, and broadcast traffic at Layer 2 from other protected ports on the same switch.
switchport trunk pruning	Configures the VLAN pruning-eligible list for ports in trunking mode.

show interfaces counters

Use the show interfaces counters privileged EXEC command to display various counters for the switch or for a specific interface.

show interfaces [interface-id | vlan vlan-id] counters [broadcast | errors | multicast | trunk | unicast] [ | {begin | exclude | include} expression]

Syntax Description

interface-id	(Optional) ID of the physical interface, including type, module, and port number.
vlan vlan-id	(Optional) VLAN number of the management VLAN. The range is 1 to 4094.
broadcast	(Optional) Display discarded broadcast traffic.
errors	(Optional) Display error counters.
multicast	(Optional) Display discarded multicast traffic.
trunk	(Optional) Display trunk counters.
unicast	(Optional) Display discarded unicast traffic.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

s

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

If you do not enter any keywords, all counters for all interfaces are included.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

This is an example of partial output from the show interfaces counters command. It displays all counters for the switch.

Switch# show interfaces counters

Port            InOctets   InUcastPkts   InMcastPkts   InBcastPkts

Gi0/1                  0             0             0             0

Gi0/2                  0             0             0             0

Gi0/3                  0             0             0             0

Gi0/4                  0             0             0             0

Gi0/5                  0             0             0             0

<output truncated>

This is an example of partial output from the show interfaces counters broadcast command. It displays dropped broadcast traffic for all interfaces.

Switch# show interfaces counters broadcast

Port      BcastSuppDiscards

Gi0/1                     0

Gi0/2                     0

Gi0/3                     0

Gi0/4                     0

Gi0/5                     0

Gi0/6                     0

<output truncated>

This is an example of output from the show interfaces counters trunk command. It displays trunk counters for all interfaces.

Switch# show interfaces counters trunk

Port        TrunkFramesTx  TrunkFramesRx  WrongEncap

Gi0/1                   0              0           0

Gi0/2                   0              0           0

Gi0/3               80678           4155           0

Gi0/4               82320            126           0

Gi0/5                   0              0           0

<output truncated>

Related Commands

Command	Description
show interfaces	Displays additional interface characteristics.
show storm-control	Displays storm-control settings for an interface or all interfaces.
storm-control	Sets storm-control broadcast, multicast, and unicast suppression levels for an interface.

show ip dhcp snooping

Use the show ip dhcp snooping user EXEC command to display the DHCP snooping configuration.

show ip dhcp snooping

Syntax Description

This command has no arguments or keywords.

Command Modes

User EXEC

Command History

Release	Modification
12.1(19)EA1	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show ip dhcp snooping command.

Switch> show ip dhcp snooping

Switch DHCP snooping is enabled

DHCP snooping is configured on following VLANs:

40-42

Insertion of option 82 is enabled

Verification of hwaddr field is enabled

Interface                    Trusted     Rate limit (pps)

------------------------     -------     ----------------

GigabitEthernet0/1               yes         unlimited

GigabitEthernet0/2               yes         unlimited

Related Commands

Command	Description
show ip dhcp snooping binding	Displays the DHCP snooping binding information.

show ip dhcp snooping binding

Use the show ip dhcp snooping binding user EXEC command to display the DHCP snooping binding database and configuration information for all interfaces on a switch.

show ip dhcp snooping binding [ip-address] [mac-address] [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression]

Syntax Description

ip-address	(Optional) Specify the binding entry IP address.
mac-address	(Optional) Specify the binding entry MAC address.
interface interface-id	(Optional) Specify the binding input interface.
vlan vlan-id	(Optional) Specify the binding entry VLAN.
| begin	Display begins with the line that matches the expression.
| exclude	Display excludes lines that match the expression.
| include	Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(19)EA1	This command was introduced.
12.2(18)SE	The dynamic and static keywords were removed.

Usage Guidelines

The show ip dhcp snooping binding command output shows the dynamically configured bindings.

If DHCP snooping is enabled and an interface changes to the down state, the switch does not delete the statically configured bindings.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This example shows how to display the DHCP snooping binding entries for a switch:

Switch> show ip dhcp snooping binding

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

------------------  ---------------  ----------  -------------  ----  --------------------

01:02:03:04:05:06   10.1.2.150       9837        dhcp-snooping  20    GigabitEthernet0/1

00:D0:B7:1B:35:DE   10.1.2.151       237         dhcp-snooping  20    GigabitEthernet0/2

This example shows how to display the DHCP snooping binding entries for a specific IP address:

Switch> show ip dhcp snooping binding 10.1.2.150

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

------------------  ---------------  ----------  -------------  ----  --------------------

01:02:03:04:05:06   10.1.2.150       9810        dhcp-snooping  20    GigabitEthernet0/1

This example shows how to display the DHCP snooping binding entries for a specific MAC address:

Switch> show ip dhcp snooping binding 0102.0304.0506

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

------------------  ---------------  ----------  -------------  ----  --------------------

01:02:03:04:05:06   10.1.2.150       9788        dhcp-snooping  20    GigabitEthernet0/2

This example shows how to display the DHCP snooping binding entries on a port:

Switch> show ip dhcp snooping binding interface gigabitethernet0/2

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

------------------  ---------------  ----------  -------------  ----  --------------------

00:30:94:C2:EF:35   10.1.2.151       290         dhcp-snooping  20    GigabitEthernet0/2

This example shows how to display the DHCP snooping binding entries on VLAN 20:

Switch> show ip dhcp snooping binding vlan 20

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

------------------  ---------------  ----------  -------------  ----  --------------------

01:02:03:04:05:06   10.1.2.150       9747        dhcp-snooping  20    GigabitEthernet0/1

00:00:00:00:00:02   10.1.2.151       65          dhcp-snooping  20    GigabitEthernet0/2

Related Commands

Command	Description
show ip dhcp snooping	Displays the DHCP snooping configuration.

show ip igmp profile

Use the show ip igmp profile privileged EXEC command to display all configured Internet Group Management Protocol (IGMP) profiles or a specified IGMP profile.

show ip igmp profile [profile number] [ | {begin | exclude | include} expression]

Syntax Description

profile number	(Optional) The IGMP profile number to be displayed. The range is 1 to 4294967295. If no profile number is entered, all IGMP profiles are displayed.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.

Examples

These are examples of output from the show ip igmp profile privileged EXEC command, with and without specifying a profile number. If no profile number is entered, the display includes all profiles configured on the switch.

Switch# show ip igmp profile 40

IGMP Profile 40

    permit

    range 233.1.1.1 233.255.255.255

Switch# show ip igmp profile

IGMP Profile 3

    range 230.9.9.0 230.9.9.0

IGMP Profile 4

    permit

    range 229.9.9.0 229.255.255.255

Related Commands

Command	Description
ip igmp profile	Configures the specified IGMP profile number.

show ip igmp snooping

Use the show ip igmp snooping user EXEC command to display the Internet Group Management Protocol (IGMP) snooping configuration of the switch or the VLAN.

show ip igmp snooping [groups | mrouter | querier] [vlan vlan-id] [ | {begin | exclude | include} expression]

Syntax Description

groups	(Optional) See the show ip igmp snooping groups command.
mrouter	(Optional) See the show ip igmp snooping mrouter command.
querier	(Optional) Display information about the IGMP version that an interface supports.
vlan vlan-id	(Optional) Specify a VLAN; the range is 1 to 4094 (available only in privileged EXEC mode).
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

The vlan vlan-id keyword is available only in privileged EXEC mode.

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(19)EA1	The querier keyword was added.
12.2(18)SE	The groups keyword was added. The show ip igmp snooping groups command replaced the show ip igmp snooping multicast command.

Usage Guidelines

Use this command to display snooping configuration for the switch or for a specific VLAN.

Although visible in the output display, output lines related to Topology change notification (TCN) and source-only learning are not supported.

Use the show ip igmp snooping querier command to display the IGMP version and ports that are associated with a multicast IP address.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show ip igmp snooping vlan 1 command. It shows snooping characteristics for a specific VLAN.

Switch# show ip igmp snooping vlan 1

Global IGMP Snooping configuration:

-----------------------------------

IGMP snooping             :Enabled

IGMPv3 snooping (minimal) :Enabled

Report suppression        :Enabled

TCN solicit query         :Disabled

TCN flood query count     :2

Vlan 1:

--------

IGMP snooping                       :Enabled

Immediate leave                     :Disabled

Multicast router learning mode      :pim-dvmrp

Source only learning age timer      :10

CGMP interoperability mode          :IGMP_ONLY

---

Note TCN and source-only learning are not supported, and information displayed about these features is not valid.

---

This is an example of output from the show ip igmp snooping command. It displays snooping characteristics for all VLANs on the switch.

Switch> show ip igmp snooping 

Global IGMP Snooping configuration:

-----------------------------------

IGMP snooping             : Enabled

IGMPv3 snooping (minimal) : Enabled

Report suppression        : Enabled

TCN solicit query         : Disabled

TCN flood query count     : 2

Vlan 1:

--------

IGMP snooping                       :Enabled

Immediate leave                     :Disabled

Multicast router learning mode      :pim-dvmrp

Source only learning age timer      :10

CGMP interoperability mode          :IGMP_ONLY

Vlan 2:

--------

IGMP snooping                       :Enabled

Immediate leave                     :Disabled

Multicast router learning mode      :pim-dvmrp

Source only learning age timer      :10

CGMP interoperability mode          :IGMP_ONLY

<output truncated>

This is an example of output from the show ip igmp snooping querier command:

Switch> show ip igmp snooping querier

Vlan      IP Address     IGMP Version        Port

---------------------------------------------------

1         172.20.50.11   v3                  Gi0/1

2         172.20.40.20   v2                  Router

Related Commands

Command	Description
ip igmp snooping	Enables and configures IGMP snooping on the switch or on a VLAN.
show ip igmp snooping mrouter	Displays IGMP snooping multicast router ports for the switch or for the specified multicast VLAN.
show ip igmp snooping groups	Displays IGMP snooping multicast information for the switch or for the specified parameter.

show ip igmp snooping mrouter

Use the show ip igmp snooping mrouter privileged EXEC command to display the Internet Group Management Protocol (IGMP) snooping dynamically learned and manually configured multicast router ports for the switch or for the specified multicast VLAN.

show ip igmp snooping mrouter [vlan vlan-id] [ | {begin | exclude | include} expression]

Syntax Description

vlan vlan-id	(Optional) Specify a VLAN; the range is 1 to 4094.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.

Usage Guidelines

Use this command to display multicast router ports on the switch or for a specific VLAN.

When multicast VLAN registration (MVR) is enabled, the show ip igmp snooping mrouter command displays MVR multicast router information and IGMP snooping information.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show ip igmp snooping mrouter command. It shows how to display multicast router ports on the switch.

Switch# show ip igmp snooping mrouter

Vlan    ports

----    -----

   1    Gi0/1(dynamic)

Related Commands

Command	Description
ip igmp snooping	Enables and configures IGMP snooping on the switch or on a VLAN.
show ip igmp snooping	Displays the IGMP snooping configuration of the switch or the VLAN
show ip igmp snooping groups	Displays IGMP snooping multicast information for the switch or for the specified parameter.

show ip igmp snooping groups

Use the show ip igmp snooping groups privileged EXEC command to display the Internet Group Management Protocol (IGMP) snooping multicast table for the switch or the multicast information. Use with the vlan keyword to display the multicast table for a specified multicast VLAN or specific multicast information.

show ip igmp snooping groups [count | dynamic [count] | user [count]] [ | {begin | exclude | include} expression]

show ip igmp snooping groups vlan vlan-id [ip_address | count | dynamic [count] | user [count]] [ | {begin | exclude | include} expression]

Syntax Description

count	(Optional) Display the total number of entries for the specified command options instead of the actual entries.
dynamic	(Optional) Display entries learned by IGMP snooping.
user	Optional) Display only the user-configured multicast entries.
ip_address	(Optional) Display characteristics of the multicast group with the specified group IP address.
vlan-id	(Optional) Specify a VLAN; the range is 1 to 4094.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.2(18)SE	This command was introduced. It replaced the show ip igmp snooping multicast command.

Usage Guidelines

Use this command to display multicast information or the multicast table.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show ip igmp snooping groups command without any keywords. It displays the multicast table for the switch.

Switch# show ip igmp snooping groups

Vlan      Group          Type        Version     Port List

-------------------------------------------------------------

104       224.1.4.2      igmp        v2          Gi0/1, Gi0/2

104       224.1.4.3      igmp        v2          Gi0/1, Gi0/2

This is an example of output from the show ip igmp snooping groups count command. It displays the total number of multicast groups on the switch.

Switch# show ip igmp snooping groups count

Total number of multicast groups: 2

This is an example of output from the show ip igmp snooping groups dynamic command. It shows only the entries learned by IGMP snooping.

Switch# show ip igmp snooping groups vlan 1 dynamic

Vlan      Group          Type        Version     Port List

-------------------------------------------------------------

104       224.1.4.2      igmp        v2          Gi0/1

104       224.1.4.3      igmp        v2          Gi0/1

This is an example of output from the show ip igmp snooping groups vlan vlan-id ip-address command. It shows the entries for the group with the specified IP address.

Switch# show ip igmp snooping groups vlan 104 224.1.4.2

Vlan      Group          Type        Version     Port List

-------------------------------------------------------------

104       224.1.4.2      igmp        v2          Gi0/1

Related Commands

Command	Description
ip igmp snooping	Enables and configures IGMP snooping on the switch or on a VLAN.
show ip igmp snooping	Displays the IGMP snooping configuration of the switch or the VLAN
show ip igmp snooping mrouter	Displays IGMP snooping multicast router ports for the switch or for the specified multicast VLAN.

show lacp

Use the show lacp user EXEC command to display Link Aggregation Control Protocol (LACP) channel-group information.

show lacp [channel-group-number] {counters | internal | neighbor | sys-id} [ | {begin | exclude | include} expression]

Syntax Description

channel-group-number	(Optional) Number of the channel group. The range is 1 to 12.
counters	Display traffic information.
internal	Display internal information.
neighbor	Display neighbor information.
sys-id	Display the system identifier that is being used by LACP. The system identifier is made up of the LACP system priority and the switch MAC address.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(14)EA1	This command was introduced.

Usage Guidelines

You can enter any show lacp command to display the active channel-group information. To display specific channel information, enter the show lacp command with a channel-group number.

If you do not specify a channel group, information for all channel groups appears.

You can enter the channel-group-number option to specify a channel group for all keywords except sys-id.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show lacp counters user EXEC command. Table 2-21 describes the fields in the display.

Switch> show lacp counters

               LACPDUs         Marker      Marker Response    LACPDUs

Port         Sent   Recv     Sent   Recv     Sent   Recv      Pkts Err

---------------------------------------------------------------------

Channel group:1

Gi0/1        19     10       0      0        0      0         0     

Gi0/2        14     6        0      0        0      0         0     

Table 2-21 show lacp counters Field Descriptions 

Field	Description
LACPDUs Sent and Recv	The number of LACP packets sent and received by a port.
Marker Sent and Recv	The number of LACP marker packets sent and received by a port.
Marker Response Sent and Recv	The number of LACP marker response packets sent and received by a port.
LACPDUs Pkts and Err	The number of unknown and illegal packets received by LACP for a port.

This is an example of output from the show lacp internal command:

Switch> show lacp 1 internal 

Flags:  S - Device is requesting Slow LACPDUs

        F - Device is requesting Fast LACPDUs

        A - Device is in Active mode       P - Device is in Passive mode 

Channel group 1

                              LACP port     Admin     Oper    Port     Port

Port        Flags   State     Priority      Key       Key     Number   State

Gi0/1       SA      bndl      32768         0x3       0x3     0x4      0x3D  

Gi0/2       SA      bndl      32768         0x3       0x3     0x5      0x3D  

Table 2-22 describes the fields in the display:

Table 2-22 show lacp internal Field Descriptions 

Field	Description
State	State of the specific port. These are the allowed values: •- —Port is in an unknown state. •bndl—Port is attached to an aggregator and bundled with other ports. •susp—Port is in a suspended state; it is not attached to any aggregator. •hot-sby—Port is in a hot-standby state. •indiv—Port is incapable of bundling with any other port. •indep—Port is in an independent state (not bundled but able to switch data traffic. In this case, LACP is not running on the partner port). •down—Port is down.
LACP Port Priority	Port priority setting. LACP uses the port priority to put ports s in standby mode when there is a hardware limitation that prevents all compatible ports from aggregating.
Admin Key	Administrative key assigned to this port. LACP automatically generates an administrative key value as a hexadecimal number. The administrative key defines the ability of a port to aggregate with other ports. A port's ability to aggregate with other ports is determined by the port physical characteristics (for example, data rate and duplex capability) and configuration restrictions that you establish.
Oper Key	Runtime operational key that is being used by this port. LACP automatically generates this value as a hexadecimal number.
Port Number	Port number.
Port State	State variables for the port, encoded as individual bits within a single octet with these meanings: •bit0: LACP_Activity •bit1: LACP_Timeout •bit2: Aggregation •bit3: Synchronization •bit4: Collecting •bit5: Distributing •bit6: Defaulted •bit7: Expired

This is an example of output from the show lacp neighbor command:

Switch> show lacp neighbor 

Flags:  S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUs

        A - Device is in Active mode       P - Device is in Passive mode     

Channel group 3 neighbors

Partner's information:

          Partner               Partner                     Partner

Port      System ID             Port Number     Age         Flags

Gi0/1     32768,0007.eb49.5e80  0xC              19s        SP

          LACP Partner         Partner         Partner

          Port Priority        Oper Key        Port State

          32768                0x3             0x3C

Partner's information:

          Partner               Partner                     Partner

Port      System ID             Port Number     Age         Flags

Gi0/2     32768,0007.eb49.5e80  0xD              15s        SP

          LACP Partner         Partner         Partner

          Port Priority        Oper Key        Port State

          32768                0x3             0x3C

This is an example of output from the show lacp sys-id command:

Switch> show lacp sys-id 

32765,0002.4b29.3a00

The system identification is made up of the system priority and the system MAC address. The first two bytes are the system priority, and the last six bytes are the globally administered individual MAC address associated to the system.

Related Commands

Command	Description
clear lacp	Clears the LACP channel-group information.
lacp port-priority	Configures the LACP port priority.
lacp system-priority	Configures the LACP system priority.

show mac access-group

Use the show mac access-group user EXEC command to display the MAC access control lists (ACLs) configured for an interface or a switch.

show mac access-group [interface interface-id] [ | {begin | exclude | include} expression]

Syntax Description

interface interface-id	(Optional) Display the MAC ACLs configured on a specific interface. Valid interfaces are physical ports and port channels; the port channel range is 1 to 64.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC; the interface keyword is available only in privileged EXEC mode.

Command History

Release	Modification
12.1(14)EA1	This command was introduced.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show mac-access group user EXEC command. In this display, Gigabit Ethernet interface 0/1 has the MAC access list macl_e1 applied; no MAC ACLs are applied to other interfaces.

Switch> show mac access-group 

Interface GigabitEthernet0/1:

   Inbound access-list is not set

Interface GigabitEthernet0/2:

   Inbound access-list is macl_e1

Interface GigabitEthernet0/3:

   Inbound access-list is not set

Interface GigabitEthernet0/4:

   Inbound access-list is not set

<output truncated>

This is an example of output from the show mac access-group interface gigabitethernet0/1 command:

Switch# show mac access-group interface GigabitEthernet0/1

Interface GigabitEthernet0/1:

   Inbound access-list is macl_e1

Related Commands

Command	Description
mac access-group	Applies a MAC access group to an interface.

show mac address-table

Use the show mac address-table user EXEC command to display a specific MAC address table static and dynamic entry or the MAC address table static and dynamic entries on a specific interface or VLAN.

show mac address-table [ | {begin | exclude | include} expression]

---

Note Beginning with Cisco IOS Release 12.1(19)EA1, the show mac address-table command replaces the show mac-address-table command (with the hyphen).

---

Syntax Description

| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(19)EA1	The show mac-address-table command was replaced by the show mac address-table command.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show mac address-table command:

Switch> show mac address-table

          Mac Address Table

------------------------------------------

Vlan    Mac Address       Type       Ports

----    -----------       ----       -----

 All    0000.0000.0001    STATIC     CPU

 All    0000.0000.0002    STATIC     CPU

 All    0000.0000.0003    STATIC     CPU

 All    0000.0000.0009    STATIC     CPU

 All    0000.0000.0012    STATIC     CPU

 All    0180.c200.000b    STATIC     CPU

 All    0180.c200.000c    STATIC     CPU

 All    0180.c200.000d    STATIC     CPU

 All    0180.c200.000e    STATIC     CPU

 All    0180.c200.000f    STATIC     CPU

 All    0180.c200.0010    STATIC     CPU

   1    0030.9441.6327    DYNAMIC    Gi0/4

Total Mac Addresses for this criterion: 12

Related Commands

Command	Description
clear mac address-table dynamic	Deletes from the MAC address table a specific dynamic address, all dynamic addresses on a particular interface, or all dynamic addresses on a particular VLAN.
show mac address-table aging-time	Displays the aging time in all VLANs or the specified VLAN.
show mac address-table count	Displays the number of addresses present in all VLANs or the specified VLAN.
show mac address-table dynamic	Displays dynamic MAC address table entries only.
show mac address-table interface	Displays the MAC address table information for the specified interface.
show mac address-table notification	Displays the MAC address notification settings for all interfaces or the specified interface.
show mac address-table static	Displays static MAC address table entries only.
show mac address-table vlan	Displays the MAC address table information for the specified VLAN.

show mac address-table address

Use the show mac address-table address user EXEC command to display MAC address table information for the specified MAC address.

show mac address-table address mac-address [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression]

---

Note Beginning with Cisco IOS Release 12.1(19)EA1, the show mac address-table address command replaces the show mac-address-table address command (with the hyphen).

---

Syntax Description

mac-address	Specify the 48-bit MAC address; the valid format is H.H.H.
interface interface-id	(Optional) Display information for a specific interface. Valid interfaces include physical ports and port channels.
vlan vlan-id	(Optional) Display entries for the specific VLAN only. The range is 1 to 4094.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(19)EA1	The show mac-address-table address command was replaced by the show mac address-table address command.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show mac address-table address command:

Switch# show mac address-table address 0002.4b28.c482

          Mac Address Table

------------------------------------------

Vlan    Mac Address     Type    Ports

----    -----------     ----    -----

 All    0002.4b28.c482  STATIC  CPU

Total Mac Addresses for this criterion: 1 

Related Commands

Command	Description
show mac address-table aging-time	Displays the aging time in all VLANs or the specified VLAN.
show mac address-table count	Displays the number of addresses present in all VLANs or the specified VLAN.
show mac address-table dynamic	Displays dynamic MAC address table entries only.
show mac address-table interface	Displays the MAC address table information for the specified interface.
show mac address-table notification	Displays the MAC address notification settings for all interfaces or the specified interface.
show mac address-table static	Displays static MAC address table entries only.
show mac address-table vlan	Displays the MAC address table information for the specified VLAN.

show mac address-table aging-time

Use the show mac address-table aging-time user EXEC command to display the aging time of a specific address table instance, all address table instances on a specified VLAN or, if a specific VLAN is not specified, on all VLANs.

show mac address-table aging-time [vlan vlan-id] [ | {begin | exclude | include} expression]

---

Note Beginning with Cisco IOS Release 12.1(19)EA1, the show mac address-table aging-time command replaces the show mac-address-table aging-time command (with the hyphen).

---

Syntax Description

vlan vlan-id	(Optional) Display aging time information for a specific VLAN. The range is 1 to 4094.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(19)EA1	The show mac-address-table aging-time command was replaced by the show mac address-table aging-time command.

Usage Guidelines

If no VLAN number is specified, the aging time for all VLANs appears.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show mac address-table aging-time command:

Switch> show mac address-table aging-time

Vlan    Aging Time

----    ----------

   1     300 

This is an example of output from the show mac address-table aging-time vlan 10 command:

Switch> show mac address-table aging-time vlan 10

Vlan    Aging Time

----    ----------

  10     300 

Related Commands

Command	Description
mac address-table aging-time	Sets the length of time that a dynamic entry remains in the MAC address table after the entry is used or updated.
show mac address-table address	Displays MAC address table information for the specified MAC address.
show mac address-table count	Displays the number of addresses present in all VLANs or the specified VLAN.
show mac address-table dynamic	Displays dynamic MAC address table entries only.
show mac address-table interface	Displays the MAC address table information for the specified interface.
show mac address-table notification	Displays the MAC address notification settings for all interfaces or the specified interface.
show mac address-table static	Displays static MAC address table entries only.
show mac address-table vlan	Displays the MAC address table information for the specified VLAN.

show mac address-table count

Use the show mac address-table count user EXEC command to display the number of addresses present in all VLANs or the specified VLAN.

show mac address-table count [vlan vlan-id] [ | {begin | exclude | include} expression]

---

Note Beginning with Cisco IOS Release 12.1(19)EA1, the show mac address-table count command replaces the show mac-address-table count command (with the hyphen).

---

Syntax Description

vlan vlan-id	(Optional) Display the number of addresses for a specific VLAN. The range is 1 to 4094.
| begin	(Optional) Display begins with the line that matches the expression.
| exclude	(Optional) Display excludes lines that match the expression.
| include	(Optional) Display includes lines that match the specified expression.
expression	Expression in the output to use as a reference point.

Command Modes

User EXEC

Command History

Release	Modification
12.1(11)AX	This command was introduced.
12.1(19)EA1	The show mac-address-table count command was replaced by the show mac address-table count command.

Usage Guidelines

If no VLAN number is specified, the address count for all VLANs appears.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.

Examples

This is an example of output from the show mac address-table count command:

Switch# show mac address-table count

Mac Entries for Vlan   : 1

---------------------------

Dynamic Address Count  : 2

Static  Address Count  : 0

Total Mac Addresses    : 2 

Related Commands

Command	Description
show mac address-table address	Displays MAC address table information for the specified MAC address.
show mac address-table aging-time	Displays the