Table Of Contents
Using the Command-Line Interface
Command Usage Basics
Accessing Command Modes
Specifying Ports in Interface Configuration Mode
Abbreviating Commands
Using the No and Default Forms of Commands
Redisplaying a Command
Getting Help
Command-Line Error Messages
Accessing the CLI
Accessing the CLI from a Browser
Saving Configuration Changes
Command Summary
Using the Command-Line Interface
This chapter provides this information:
•
Command Usage Basics
•Command-Line Error Messages
•Accessing the CLI
•Saving Configuration Changes
•Command Summary
You can use the switch command-line interface (CLI) to configure and monitor the switch features, as described in the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide.
This reference manual provides detailed information about the commands that have been created or changed specifically for the Catalyst 2900 XL and Catalyst 3500 XL switches. This manual also provides information about configuring the Cisco Long-Reach Ethernet (LRE) customer premises equipment (CPE) devices.
Note This switch software release is based on Cisco IOS Release 12.0. It has been enhanced to support a set of features for the Catalyst 2900 XL and Catalyst 3500 XL switches. This reference manual does not repeat the CLI commands already documented in the Cisco IOS Release 12.0 documentation on Cisco.com.
Note This manual describes the features for all Catalyst 2900 XL and Catalyst 3500 XL switches, including the Catalyst 2900 LRE XL switches. Cisco IOS Release 12.0(5)WC5 is not for the Long-Reach Ethernet (LRE) switches. Do not install Release 12.0(5)WC5 on the Catalyst 2900 LRE XL switches.
Release 12.0(5)WC6 is only for the Catalyst 2900 LRE XL switches. Do not install Release 12.0(5)WC6 on non-LRE switches.
The Cisco IOS Releases 12.0(5)WC4 and 12.0(5)WC5 software supports the hardware listed in the release notes (http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/index.htm).
Command Usage Basics
This section provides these topics:
•"Accessing Command Modes" section
•"Specifying Ports in Interface Configuration Mode" section
•"Abbreviating Commands" section
•"Using the No and Default Forms of Commands" section
•"Redisplaying a Command" section
•"Getting Help" section
For complete information about CLI usage, refer to the Cisco IOS Release 12.0 documentation on Cisco.com.
Accessing Command Modes
The CLI is divided into different modes. The commands available to you at any given time depend on which mode you are in. Entering a question mark (?) at the system prompt provides a list of commands for each command mode.
When you start a session on the switch, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands are one-time commands, such as show commands, which show the current configuration status, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the switch reboots.
To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password to enter privileged EXEC mode. From this mode, you can enter any privileged EXEC command or enter global configuration mode.
Using the configuration modes (such as global, VLAN, and interface), you can make changes to the running configuration. If you save the configuration, these commands are stored when the switch reboots. To access the various configuration modes, you must start at global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.
Table 1-1 describes the main command modes supported on the switch, the prompt you see in that mode, and how to exit the mode. The examples in the table use the host name switch.
Table 1-1 Command Modes Summary
Modes
|
Access Method
|
Prompt
|
Exit Method
|
|
User EXEC
|
Begin a session with your switch.
|
|
Enter logout or quit.
|
The EXEC commands available at the user level are a subset of those available at the privileged level.
Use this mode to
•Change terminal settings.
•Perform basic tests.
•Display system information.
|
Privileged EXEC
|
Enter the enable command while in user EXEC mode.
|
|
Enter disable to exit.
|
The privileged command set includes those commands contained in user EXEC mode, as well as the configure command through which you access the remaining command modes. Because many of the privileged commands configure operating parameters, privileged access should be password-protected to prevent unauthorized use.
If your system administrator has set a password, you are prompted to enter it before being granted access to privileged EXEC mode. The password does not appear on the screen and is case sensitive.
|
Global configuration
|
Enter the configure command while in privileged EXEC mode.
|
|
To exit to privileged EXEC mode, enter exit or end, or press Ctrl-Z.
|
Use this mode to configure parameters that apply to your switch as a whole.
|
VLAN database
|
Enter the vlan database command while in privileged EXEC mode.
|
|
To exit to privileged EXEC mode, enter exit.
|
Use this mode to configure VLAN-specific parameters.
|
Controller configuration
|
Enter the controller longreachethernet command (with a specific interface) while in global configuration mode.
|
Switch(config-contro
ller)#
|
To exit to global configuration mode, enter exit.
To exist to privileged EXEC mode, enter Ctrl-Z or end.
|
Controller configuration
|
Interface configuration
|
Enter the interface command (with a specific interface) while in global configuration mode.
|
|
To exit to global configuration mode, enter exit.
To exist to privileged EXEC mode, enter Ctrl-Z or end.
|
Interface configuration
|
Sequence configuration
|
Enter the lre sequence command while in global configuration mode.
|
|
To exit to global configuration mode, enter exit.
To exit to privileged EXEC mode, enter Ctrl-Z or end.
|
Use this mode on Long-Reach Ethernet switches to configure sequences for rate selection.
|
Line configuration
|
Specify a line with the line vty or line console command while in global configuration mode.
|
|
To exit to global configuration mode, enter exit.
To exit to privileged EXEC mode, enter Ctrl-Z or end.
|
Use this mode to configure parameters for the terminal line.
|
Specifying Ports in Interface Configuration Mode
To configure a port, you need to specify the interface type, slot, and switch-port number with the interface configuration command. For example, to configure port 4 on a switch, you enter:
switch(config)#interface fa 0/4
To configure port 4 on a 10/100 module in the first module slot on the switch, you enter:
switch(config)#interface fa 1/4
•Interface type—Each switch in the Catalyst 2900 series XL and Catalyst 3500 series XL platform supports different types of interfaces. To display a complete list of the interface types supported on your switch, enter the interface ? command from the global configuration mode. This example shows what the interface ? command displays on a Catalyst 2900 LRE XL switch:
lreswitch(config)#interface ?
FastEthernet FastEthernet IEEE 802.3
LongReachEthernet Ethernet over VDSL
Multilink Multilink-group interface
Port-channel Ethernet Channel of interfaces
VLAN Switch VLAN Virtual Interface
Virtual-TokenRing Virtual TokenRing
Note The multilink, port-channel, and virtual-Token Ring interface types are not supported on the Catalyst 2900 XL and Catalyst 3500 XL switches.
•Slot number—The slot number on the switch. On the modular Catalyst 2900 XL switches, the slot number is 1 or 2. On non-modular Catalyst 2900 XL and Catalyst 3500 XL switches, the slot number is 0.
•Port number—The number of the physical port on the switch. Refer to your switch for the port numbers.
Abbreviating Commands
You only have to enter enough characters for the switch to recognize the command as unique. This example shows how to enter the show configuration command:
Using the No and Default Forms of Commands
Almost every configuration command has a no form. In general, use the no form to
•Disable a feature or function.
•Reset a command to its default values.
•Reverse the action of a command. For example, the no shutdown command reverses the shutdown of an interface.
Use the command without the no form to reenable a disabled feature or to reverse the action of a no command.
Configuration commands can also have a default form. The default form of a command returns the command setting to its default. Most commands are disabled by default, so the default form is the same as the no form. However, some commands are enabled by default and have variables set to certain default values. In these cases, the default command enables the command and sets variables to their default values.
Redisplaying a Command
To redisplay a command you previously entered, press the up-arrow key. You can continue to press the up-arrow key for more commands.
Getting Help
Entering a question mark (?) at the system prompt displays a list of commands for each command mode. When using context-sensitive help, the space (or lack of a space) before the question mark (?) is significant. To obtain a list of commands that begin with a particular character sequence, enter those characters followed immediately by the question mark (?). Do not include a space. This form of help is called word help, because it completes a word for you.
To list keywords or arguments, enter a question mark (?) in place of a keyword or argument. Include a space before the ?. This form of help is called command syntax help, because it reminds you which keywords or arguments are applicable based on the command, keywords, and arguments you already have entered.
You can also obtain a list of associated keywords and arguments for any command, as shown in Table 1-2.
Table 1-2 Help Summary
Command
|
Purpose
|
help
|
Obtain a brief description of the help system in any command mode.
|
abbreviated-command-entry?
|
Obtain a list of commands that begin with a particular character string. For example:
|
abbreviated-command-entry<Tab>
|
Complete a partial command name. For example:
Switch# show configuration
|
?
|
List all commands available for a particular command mode. For example:
|
command ?
|
List the associated keywords for a command. For example:
|
command keyword ?
|
List the associated arguments for a keyword. For example:
Switch(config)# cdp holdtime ?
<10-255> Length of time (in sec) that receiver must keep this packet
|
Command-Line Error Messages
Table 1-3 lists some error messages that you might encounter while using the CLI.
Table 1-3 Common CLI Error Messages
Error Message
|
Meaning
|
How to Get Help
|
% Ambiguous command: "show con"
|
You did not enter enough characters for your switch to recognize the command.
|
Reenter the command followed by a space and a question mark (?).
The possible keywords that you can enter with the command appear.
|
|
You did not enter all of the keywords or values required by this command.
|
Reenter the command followed by a space and a question mark (?).
The possible keywords that you can enter with the command appear.
|
% Invalid input detected at `^'
marker.
|
You entered the command incorrectly. The caret (^) marks the point of the error.
|
Enter a question mark (?) to display all of the commands that are available in this command mode.
The possible keywords that you can enter with the command appear.
|
Accessing the CLI
This procedure assumes you have already assigned IP information and password to the switch or command switch. You can assign this information to the switch in these ways:
•Using the setup program, as described in the release notes (http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/index.htm).
•Manually assigning an IP address and password, as described in the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide.
To access the CLI from a terminal session, follow these steps:
Step 1 Start up the emulation software (such as ProComm, HyperTerminal, tip, or minicom) on the management station.
Step 2 If necessary, reconfigure the terminal-emulation software to match the switch console port settings (default settings are 9600 baud, no parity, 8 data bits, and 1 stop bit).
Step 3 Establish a connection with the switch by either
•Connecting the switch console port to a management station or dial-up modem. For information about connecting to the console port, refer to the switch hardware installation guide.
•Using any Telnet TCP/IP package from a remote management station. The switch must have network connectivity with the Telnet client, and the switch must have an enable secret password configured. For information about configuring the switch for Telnet access, refer to the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide.
The switch supports up to seven simultaneous Telnet sessions. Changes made by one Telnet user are reflected in all other Telnet sessions.
After you connect through the console port or through a Telnet session, the User EXEC prompt appears on the management station.
Accessing the CLI from a Browser
This procedure assumes you have met the software requirements, (including browser and Java plug-in configurations) and have assigned IP information and a Telnet password to the switch or command switch, as described in the release notes (http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/index.htm).
Caution Copies of the CMS pages you display are saved in your browser memory cache until you exit the browser session. A password is not required to redisplay these pages, including the Cisco Systems Access page. You can access the CLI by clicking
Web Console - HTML access to the command line interface from a cached copy of the Cisco Systems Access page. To prevent unauthorized access to CMS and the CLI, exit your browser to end the browser session.
To access the CLI from a web browser, follow these steps:
Step 1 Start one of the supported browsers.
Step 2 In the URL field, enter the IP address of the command switch.
Step 3 When the Cisco Systems Access page appears, click Telnet to start a Telnet session.
You can also access the CLI by clicking Web Console - HTML access to the command line interface from the Cisco Systems Access page. For information about the Cisco Systems Access page, see the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide and the release notes (http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/index.htm).
Step 4 Enter the switch password.
The User EXEC prompt appears on the management station.
Saving Configuration Changes
The switch Flash memory stores the IOS image, the startup configuration file (config.txt file), and helper files.
The show command always displays the running configuration of the switch. When you make a configuration change to a switch or switch cluster, the change becomes part of the running configuration. The change does not automatically become part of the config.txt file in Flash memory, which is the startup configuration used each time the switch restarts. If you do not save your changes to Flash memory, they are lost when the switch restarts.
To save all configuration changes to Flash memory, you must enter the write memory command in privileged EXEC mode.
Note The write memory command does not apply to the Catalyst 1900 and Catalyst 2820 switches, which automatically save configuration changes to Flash memory as they occur.
Tip As you make cluster configuration changes, make sure you periodically save the configuration. The configuration is saved on the command and member switches.
Command Summary
Table 1-4 lists and describes the IOS commands specifically created or modified for the Catalyst 2900 XL or the Catalyst 3500 XL switches. Long-Reach Ethernet (LRE) commands only apply to the Catalyst 2900 XL LRE switches. The commands are sorted by the command modes from which they are entered.
For detailed command syntax and descriptions, see "Cisco IOS Commands." For concepts and procedures, refer to the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide.
Table 1-4 Command Summary
Commands
|
Description
|
User EXEC mode
|
| |
rcommand
|
Executes commands on a cluster member from the command switch.
|
| |
show cluster
|
Displays the cluster status and a summary of the cluster to which the switch belongs.
|
| |
show cluster candidates
|
Displays switches that are not currently members of the cluster but that could be.
|
| |
show cluster members
|
Displays information about all members in a cluster.
|
| |
show errdisable detect
|
Displays error-disable detection status.
|
| |
show errdisable recovery
|
Displays the error-disable recovery timer information.
|
| |
show diags
|
Displays the state of a port or all ports on the switch.
|
| |
show mac-address-table
|
Displays the MAC address table.
|
| |
show remote ethernet-statistics
|
Displays the statistics for the Ethernet ports on the LRE CPE devices connected to the switch LRE ports.
|
| |
show remote interfaces status
|
Displays the speed, duplex mode, and link status of the Ethernet ports on the LRE CPE devices connected to the switch LRE ports.
|
| |
show rps
|
Displays the status of the Cisco Redundant Power System (RPS).
|
| |
show spanning-tree
|
Displays STP information.
|
| |
show tacacs
|
Displays various Terminal Access Controller Access Control System Plus (TACACS+) server statistics.
|
| |
show udld
|
Displays UDLD status information for all ports or the specified port.
|
| |
show version
|
Displays the firmware version for the switch or the module.
|
| |
show vlan
|
Displays information about a VLAN.
|
| |
show vmps
|
Displays the VLAN Query Protocol (VQP) version, the reconfirmation interval, the retry count, the VLAN Membership Policy Server (VMPS) IP addresses, and the current and primary servers.
|
| |
show vtp
|
Displays general information about the VTP management domain, status, and counters.
|
Privileged EXEC mode
|
| |
clear cgmp
|
Deletes the multicast addresses and router ports maintained by CGMP.
|
| |
clear controllers ethernet-controller
|
Deletes the Ethernet link transmit and receive statistics on a switch port and on an LRE CPE (if one is connected to a switch LRE port).
|
| |
clear controllers lre log
|
Deletes the history of link, configuration, and timer events for a specific switch LRE port or all LRE ports on the switch.
|
| |
clear lre rate selection
|
Resets the current rate selection setting and restarts rate selection for a specific Long-Reach Ethernet (LRE) port or for all switch LRE ports.
|
| |
clear mac-address-table
|
Deletes the IP address without disabling the IP processing.
|
| |
clear mac-address-table
|
Deletes all addresses in the MAC address table.
|
| |
clear mac-address-table notification
|
Deletes entries from the MAC address notification table.
|
| |
clear vmps statistics
|
Clears the statistics maintained by the VLAN Query Protocol (VQP) client.
|
| |
clear vtp counters
|
Clears the VTP counters.
|
| |
debug lre
|
Enables debugging of LRE-related events.
|
| |
delete
|
Deletes a file from the file system.
|
| |
hw-module slot module-slot # upgrade lre
|
Performs system-wide software upgrades.
|
| |
session
|
Logs into an ATM module.
|
| |
show cgmp
|
Displays the current state of the CGMP-learned multicast groups and routers.
|
| |
show controllers ethernet-controller
|
Displays the Ethernet link transmit and receive statistics on a Fast Ethernet or switch LRE port.
|
| |
show controllers lre cpe info
|
Displays the model numbers of the LRE CPE devices connected to the LRE switch and shows whether or not the connected CPEs meet the minimum requirements to be managed by the LRE switch.
|
| |
show controllers lre interface-id actual
|
Displays the actual values of the LRE link on a specific switch LRE port.
|
| |
show controllers lre interface-id admin
|
Displays the administrative settings of the LRE link on a specific switch LRE port.
|
| |
show controllers lre log
|
Displays the history of link, configuration, and timer events for a specific switch LRE port or all LRE ports on the switch.
|
| |
show controllers lre log level
|
Displays information about the LRE event log level.
|
| |
show controllers lre profile
|
Displays information about the LRE profiles available on the switch and how they are assigned to the switch LRE ports.
|
| |
show controllers lre sequence
|
Displays information about the LRE port and global sequences.
|
| |
show controllers lre status
|
Displays the LRE link statistics and profile information on a switch LRE port, including link state, link duration, data rates, power levels, sequence and signal-to-noise ratio (SNR) error information. It also displays the Reed-Solomon error information and other line characteristics.
|
| |
show controllers lre version
|
Displays the version numbers of the various components (hardware, firmware, patch software, and bootloader firmware and application firmware) that make up the switch LRE interface and the CPE LRE interface.
|
| |
show controllers lre version mfg
|
Displays the revision and serial numbers of the connected LRE CPE board, assembly, and system.
|
| |
show diags
|
Displays the current state of a port or all ports on the switch.
|
| |
show env
|
Displays the status of the Catalyst 3524-PWR XL switch fans and temperature.
|
| |
show file systems
|
Displays information about local and remote file systems.
|
| |
show interface
|
Displays the administrative and operational status of a switch port.
|
| |
show ip igmp profile
|
Displays the details of an IGMP profile entry.
|
| |
show local ethernet-statistics
|
Displays the details of the local VDSL chipset.
|
| |
show lre upgrade binaries
|
Displays the LRE binaries present on the system Flash memory.
|
| |
show lre upgrade status
|
Displays the upgrade status on all ports in the switch.
|
| |
show lre upgrade version
|
Displays the version of binaries on local and remote ports in the switch.
|
| |
show mac-address-table notification
|
Displays the global parameters for the MAC address table notification feature.
|
| |
show mvr
|
Displays the current multicast VLAN registration (MVR) global parameter values, including whether or not MVR is enabled, the maximum query response time, the maximum number of multicast entries, and the multicast VLAN number.
|
| |
show mvr interface
|
Displays the MVR receiver and source ports. Use the command with keywords to display MVR parameters for a specific receiver port.
|
| |
show mvr members
|
Displays all receiver ports that are members of an IP multicast group.
|
| |
show port block
|
Displays the blocking of unicast and multicast filtering for the port.
|
| |
show port group
|
Displays the ports that are assigned to groups.
|
| |
show port monitor
|
Displays the ports that have port monitoring enabled.
|
| |
show port network
|
Displays the network ports on the switch.
|
| |
show port protected
|
Displays the ports that are port protected mode.
|
| |
show port security
|
Displays the ports that have port security enabled.
|
| |
show port storm-control
|
Displays the setting of broadcast-storm control.
|
| |
show power inline
|
Displays the power status for the specified port or all ports on the 3524-PWR-XL switch.
|
| |
show tech-support
|
Displays general switch information for determining the nature of a switch error or for providing to a Cisco technical support representative.
|
| |
show vmps statistics
|
Displays the VQP client-side statistics.
|
| |
udld reset
|
Resets all ports that have been shut down by UDLD.
|
| |
vlan database
|
Enters VLAN database mode.
|
| |
vmps reconfirm
|
Sends VQP queries to reconfirm all dynamic VLAN assignments with the VLAN Membership Policy Server (VMPS).
|
Global configuration mode
|
| |
cgmp
|
Enables CGMP and other CGMP options.
|
| |
cluster commander-address
|
Automatically provides the command switch MAC address to member switches. This command is automatically issued.
|
| |
cluster discovery hop-count
|
Sets the hop-count limit for extended discovery of cluster candidates.
|
| |
cluster enable
|
Enables the cluster command switch and names the cluster.
|
| |
cluster holdtime
|
Sets the timer that determines when a command switch declares the other switch down after not receiving a heartbeat message. Used with the cluster timer command.
|
| |
cluster management-vlan
|
Changes the management VLAN for the entire cluster.
|
| |
cluster member
|
Adds members to the cluster.
|
| |
cluster run
|
Enables clustering on a switch.
|
| |
cluster standby-group
|
Enables command switch redundancy by binding an HSRP standby group to the cluster.
|
| |
cluster timer
|
Specifies the interval between heartbeat messages between the command and member switches. Used with the cluster holdtime command.
|
| |
controller LongReachEthernet
|
Enters controller configuration mode.
|
| |
errdisable detect cause
|
Enables error disable detection for a cause.
|
| |
errdisable recovery
|
Configures the recovery mechanism variables.
|
| |
interface
|
Selects an interface to configure. Creates a new management VLAN interface.
|
| |
ip igmp profile
|
Defines a new profile for IGMP filtering or deletes an existing IGMP filtering profile.
|
| |
lre patchfile
|
Specifies the LRE patch file used when the switch starts up.
|
| |
lre profile global
|
Assigns a public profile to all switch LRE ports.
|
| |
lre rate selection sequence
|
Assigns the rate selection sequence for the entire switch.
|
| |
lre sequence
|
Defines a new sequence and also enters sequence configuration mode.
|
| |
lre upgrade default family device-family binary
|
Defines a default mapping between an LRE device type and an LRE binary.
|
| |
mac-address-table aging-time
|
Specifies the length of time that a dynamic entry remains in the MAC address table.
|
| |
mac-address-table dynamic
|
Adds a dynamic address entry to the MAC address table.
|
| |
mac-address-table notification
|
Enables the MAC address table notification feature on the switch.
|
| |
mac-address-table secure
|
Adds a secure address entry to the MAC address table.
|
| |
mac-address-table static
|
Adds a static address entry to the address table.
|
| |
mvr (global configuration)
|
Enables the Multicast VLAN Registration (MVR) feature on the switch.
|
| |
ntp max-associations
|
Specifies the maximum number of NTP associations that are allowed on a server.
|
| |
ntp source
|
Uses a particular source address in NTP packets.
|
| |
shutdown vlan
|
Shuts down local traffic on the specified VLAN.
|
| |
snmp-server enable traps mac-notification
|
Enables SNMP notification for MAC address notification.
|
| |
snmp-server enable traps vlan-membership
|
Enables SNMP notification for VMPS changes.
|
| |
snmp-server enable traps vtp
|
Enables SNMP notification for VTP changes.
|
| |
snmp-server host
|
Specifies the host that receives SNMP traps.
|
| |
spanning-tree
|
Enables a spanning-tree instance.
|
| |
spanning-tree forward-time
|
Specifies the forward delay interval for the switch.
|
| |
spanning-tree hello-time
|
Specifies the interval between hello Bridge Protocol Data Units (BPDUs).
|
| |
spanning-tree max-age
|
Changes the interval the switch waits to receive BPDUs from the root switch.
|
| |
spanning-tree portfast bpduguard
|
Enables the BPDU guard feature on the switch.
|
| |
spanning-tree priority
|
Configures the bridge priority for the specified spanning-tree instance.
|
| |
spanning-tree protocol
|
Defines the type of STP.
|
| |
spanning-tree uplinkfast
|
Accelerates the choice of a new root port when a link or switch fails or when STP reconfigures itself.
|
| |
tacacs-server attempts
|
Controls the number of login attempts that can be made on a line configured for TACACS, Extended TACACS, or TACACS+ verification.
|
| |
tacacs-server dns-alias-lookup
|
Enables IP Domain Name System alias lookup for TACACS+.
|
| |
udld enable
|
Enables UDLD on all switch ports.
|
| |
vmps reconfirm
|
Changes the reconfirmation interval for the VQP client.
|
| |
vmps retry
|
Configures the per-server retry count for the VQP client.
|
| |
vmps server
|
Configures the primary VMPS and up to three secondary servers.
|
| |
vtp file
|
Modifies the VTP configuration storage filename.
|
VLAN database mode
|
| |
abort
|
Abandons the proposed VLAN database and returns to privileged EXEC mode.
|
| |
apply
|
Implements the proposed VLAN database, propagates it throughout the administrative domain, and remains in VLAN database mode.
|
| |
exit
|
Implements the proposed VLAN database, propagates it throughout the administrative domain, and returns to privileged EXEC mode.
|
| |
reset
|
Abandons the proposed VLAN database and remains in VLAN database mode.
|
| |
show changes
|
Displays the differences between the current VLAN database on the switch and the proposed VLAN database.
|
| |
show current
|
Displays the current VLAN database on the switch or a single selected VLAN from it.
|
| |
show proposed
|
Displays the proposed VLAN database or a single selected VLAN from it.
|
| |
vlan
|
Configures a VLAN by its VLAN ID.
|
| |
vtp
|
Configures the VTP mode.
|
| |
vtp domain
|
Configures the VTP administrative domain.
|
| |
vtp password
|
Configures the VTP password.
|
| |
vtp pruning
|
Enables pruning in the VTP administrative domain.
|
| |
vtp v2-mode
|
Enables VTP version 2 mode in the administrative domain.
|
Controller configuration mode
|
| |
upgrade binary
|
Configures a Long-Reach Ethernet (LRE) controller upgrade.
|
| |
upgrade preserve
|
Prevents an upgrade from taking place on a controller in a Long-Reach Ethernet (LRE) switch and on all the devices that are remotely connected to it.
|
Interface configuration mode
|
| |
duplex
|
Specifies the duplex mode of operation for a port.
|
| |
flowcontrol
|
Controls traffic rates during congestion.
|
| |
ip address
|
Specifies a primary or secondary IP address of a VLAN interface.
|
| |
ip igmp filter
|
Applies a specific IGMP filtering profile to an interface.
|
| |
ip igmp max-groups
|
Specifies the maximum number of IGMP profiles that can be active on a port.
|
| |
lre log
|
Specify the logging mode for LRE events.
|
| |
lre persistence
|
Sets the amount of delay before the link reports a link failure.
|
| |
lre profile
|
Assigns a private profile to a specific switch LRE port.
|
| |
lre reset
|
Resets the switch LRE interface or the CPE LRE interface.
|
| |
lre shutdown
|
Disables the LRE interface transmitter of a switch LRE port that is not being used.
|
| |
management
|
Shuts down the management VLAN interface.
|
| |
margin
|
Specifies the margin value used to determine link quality during Long-Reach Ethernet (LRE) rate selection.
|
| |
mvr (interface configuration)
|
Configures a port as an MVR receiver or source port, specifies the Immediate-Leave feature, and configures the port threshold.
|
| |
ntp broadcast client
|
Allows the system to receive NTP broadcast packets on a port.
|
| |
ntp broadcast destination
|
Configures an NTP server or peer to restrict broadcast of NTP frames to the IP address of a designated client or a peer.
|
| |
ntp broadcast key
|
Configures an NTP server or peer to broadcast NTP frames with the authentication key embedded in the NTP packet.
|
| |
ntp broadcast version
|
Specifies a port to send NTP broadcast packets.
|
| |
port block
|
Prevents the flooding of unknown destination MAC addresses and multicast addresses on this port.
|
| |
port group
|
Places a port into a port aggregation group.
|
| |
port monitor
|
Implements port monitoring on this port.
|
| |
port network
|
Enables a port as the network port for a VLAN.
|
| |
port protected
|
Isolates unicast, multicast, and broadcast traffic at Layer 2 from other protected ports on the same switch.
|
| |
port security
|
Enables port security on a port, sets the aging time for dynamic and static secure address entries, and restricts the use of the port to a user-defined group of stations.
|
| |
port storm-control
|
Disables broadcast, multicast, or unicast traffic if too many packets are seen on this port.
|
| |
power inline
|
Specifies how inline power is applied to the device on the specified Fast Ethernet port of the Catalyst 3524-PWR XL switch.
|
| |
rate selection
|
Enables rate selection on a port.
|
| |
rate selection profile lock
|
Locks a profile in a port that is enabled for rate selection.
|
| |
rate selection sequence
|
Assigns a sequence to a port and to start rate selection.
|
| |
rmon collection stats
|
Collects Ethernet group statistics.
|
| |
shutdown
|
Disables a switch port, including the Ethernet ports on the LRE CPE connected to a switch LRE port.
|
| |
snmp trap mac-notification
|
Enables or disables the MAC notification feature on a specific port.
|
| |
spanning-tree cost
|
Specifies a different path cost.
|
| |
spanning-tree portfast
|
Enables the Port Fast option on the switch.
|
| |
spanning-tree port-priority
|
Configures the STP priority of a port.
|
| |
spanning-tree rootguard
|
Enables the root guard feature for all the VLANs associated with the specified port. Controls which ports can be STP root ports.
|
| |
spanning-tree stack-port
|
Enables cross-stack UplinkFast (CSUF) on an interface and accelerates the choice of a new root port when a link or switch fails or when STP reconfigures itself.
|
| |
speed
|
Specifies the speed of a port.
|
| |
switchport access
|
Configures a port as an access or dynamic VLAN port.
|
| |
switchport mode
|
Configures the VLAN membership mode of a port.
|
| |
switchport multi
|
Configures a port to be a multi-VLAN port.
|
| |
switchport priority
|
Configures a port priority for untagged (native Ethernet) frames to provide quality of service (QoS). Also sets the priority of frames received by the appliance connected to the specified port.
|
| |
switchport trunk allowed vlan
|
Controls which VLANs can receive and send traffic on the trunk.
|
| |
switchport trunk encapsulation
|
Sets the encapsulation format on the trunk.
|
| |
switchport trunk native
|
Sets the native VLAN for untagged traffic when in IEEE 802.1Q trunking mode.
|
| |
switchport trunk pruning
|
Sets the list of VLANs enabled for VTP pruning when the port is in trunking mode.
|
| |
switchport voice vlan
|
Sets the voice VLAN on the port.
|
| |
udld
|
Enables or disables UDLD on a port.
|
Line configuration mode
|
| |
login local
|
Changes a login username.
|
| |
login tacacs
|
Configures the switch to use TACACS user authentication.
|
Sequence mode
|
| |
profile
|
Adds a Long-Reach Ethernet (LRE) profile to a rate selection sequence.
|
