Feedback
Table Of Contents
System Messages and Recovery Procedures for Cisco NX-OS
LC_PORT_CHANNEL-SLOT# Messages
System Messages and Recovery Procedures for Cisco NX-OS
This chapter includes system messages for the Cisco NX-OS MDS 9000, Nexus 7000, Nexus 5000, Nexus 1000 families of switches, and for Cisco Virtual Security Gateway. The messages are listed in alphabetical order by the system facility that produces them. Within each system facility section, messages are listed alphabetically by severity and mnemonics. Each error message is followed by an explanation and a recommended action.
AAA Messages
This section contains the AAA messages.
AAA-1
Error Message AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request rejected as maximum aaa sessions are in progressExplanation An AAA request has been rejected because the system has detected that the limit for the maximum concurrent AAA sessions has been exceeded.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-1-SESSION_LIMIT_REJECT Format: aaa request rejected as maximum aaa sessions are in progressExplanation aaa request rejected as the limit for maximum concurrent aaa sessions is reached.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-2
Error Message AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. [chars]Explanation The system has detected that the accounting log upgrade has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting: [chars]Explanation The system has detected that the AAA daemon has exited.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-2-NVRAM_UPGRADE_FAILURE Format: upgrading of accounting log failed. %s\nExplanation upgrading of accounting log failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-2-PROGRAM_EXIT Format: aaa daemon exiting: %s\nExplanation aaa daemon is exiting.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-3
Error Message AAA-3-AAA_NVRAMFAILURE: nvram failureExplanation The system has detected that because the NVRAM cannot be read/written to, the accounting log cannot be stored in NVRAM.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-3-NVRAMFAILURE Format: nvram failureExplanation nvram cannot be read/written to. Hence accounting log can not be stored there.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-6
Error Message AAA-6-AAA_ACCOUNTING_MESSAGE: [chars]Explanation This message indicates that this is an accounting message.
Recommended Action No action is required.
Error Message AAA-6-ACCOUNTING_MESSAGE Format: %sExplanation This message indicates that this is an accounting message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAM Messages
This section contains the AAM messages.
AAM-2
Error Message AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED Format: Failed to lookup global port index for interface [%s]Explanation Failed to lookup global port index for interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED: Failed to lookup global port index for interface [[chars]]Explanation Failed to lookup global port index for interface [chars].
Recommended Action No action is required.
AAM-3
Error Message AAM-3-ALLOC_FAILED Format: Failed in File:%s Line:%d for type %d size %dExplanation AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAM-3-ALLOC_FAILED: Failed in File:[chars] Line:[dec] for type [dec] size [dec]Explanation AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].
Recommended Action No action is required.
Error Message AAM-3-ASSERTION_FAILED Format: Failed in File:%s Line:%dExplanation AAM Process assertion failed in File:[chars], at line:[dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAM-3-ASSERTION_FAILED: Failed in File:[chars] Line:[dec]Explanation AAM Process assertion failed in File:[chars], at line:[dec].
Recommended Action No action is required.
ACL Messages
This section contains the ACL messages.
ACL-2
Error Message ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: [chars].Explanation The system has failed to do a high availability operation. [chars] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_INIT_FAILED: Initialization failed for ACL: [chars], reason: [hex].Explanation Initialization failed for ACL due to [chars], reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].Explanation This message indicates that this message is a status from the line card [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars].Explanation The system has failed to do an MTS operation. [chars] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options setting to [hex] failed for opCode: [dec].Explanation The MTS options setting to [hex] failed for opCode: [dec].
Recommended Action No action is required.
Error Message ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade Pending Messages Array is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]Explanation This message indicates that the ACL upgrade pending messages array is full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].Explanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec].Explanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.
Recommended Action No action is required.
Error Message ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error: [hex]Explanation The system detects than an ACL runtime failure has occurred as [chars] [dec], reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars].Explanation The system has failed to do a TCAM operation. [chars] is the reason.
Recommended Action No action is required.
Error Message ACL-2-HA_FAILURE Format: Failed to do high availability operation: %s.Explanation The system has failed to do a high availability operation. [chars] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-INIT_FAILED Format: Initialization failed for ACL: %sExplanation Initialization failed for ACL due to [chars], reason: [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-MTS_FAILURE Format: Failed to do MTS operation: %s.Explanation The system has failed to do an MTS operation. [chars] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-MTS_REGISTRATION_FAILED Format: MTS options setting to %x failed for opCode: %d.Explanation The MTS options setting to [hex] failed for opCode: [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-PENDING_MSG_ARR_FULL Format: ACL Upgrade Pending Messages Array is Full with %d messages. Failing the MTS message with Opc: %dExplanation This message indicates that the ACL upgrade pending messages array is full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-PSS_FAILURE Format: Failed to do PSS operation: %sExplanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-PSS_VER_FAIL Format: PSS file %s has version %d.%d.%dExplanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-RUNTIME_FAILURE Format: %s %dExplanation The system detects than an ACL runtime failure has occurred as [chars] [dec], reason: [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-2-TCAM_FAILURE Format: Failed to do TCAM operation: %s.Explanation The system has failed to do a TCAM operation. [chars] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL-4
Error Message ACL-4-ACL_WARNING: [chars] [dec]Explanation ACL warning messages are reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-4-WARNING Format: %s %dExplanation ACL warning messages are reported as [chars] [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL-5
Error Message ACL-5-ACL_ADJ_SHARING_STATUS: Successfully completed [chars] on Generation 2 linecards.Explanation Successfully completed the command \[chars]\ on Generation 2 line cards.
Recommended Action No action is required.
Error Message ACL-5-ADJ_SHARING_STATUS Format: Successfully completed %s on Generation 2 linecards.Explanation Successfully completed the command [chars] on Generation 2 line cards.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL-6
Error Message ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex].Explanation ACL system health management event status is reported as [chars] [hex].
Recommended Action No action is required.
Error Message ACL-6-ACL_E_PORT_EVENT_STATUS: [chars] [chars].Explanation ACL E port event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars].Explanation ACL FCC event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex].Explanation ACL line card event status is reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars].Explanation ACL multicast event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars] [chars].Explanation ACL Nx Port event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars].Explanation ACL portmode event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_RUNTIME_STATUS: [chars] [dec]Explanation ACL runtime status is reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars] [chars].Explanation ACL SPAN destination config event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars].Explanation ACL SPAN source configuration event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_STATUS: ACL Status: [chars].Explanation ACL status is reported as [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars] [chars].Explanation ACL update SSRAM for QoS event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-DIAG_EVENT_STATUS Format: %s 0x%x.Explanation ACL system health management event status is reported as [chars] [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-E_PORT_EVENT_STATUS Format: %s %s.Explanation ACL E port event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-FCC_EVENT_STATUS Format: %s %s.Explanation ACL FCC event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-LINECARD_EVENT_STATUS Format: %s %x.Explanation ACL line card event status is reported as [chars] [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-MCAST_EVENT_STATUS Format: %s %s.Explanation ACL multicast event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-NX_PORT_EVENT_STATUS Format: %s %s.Explanation ACL Nx Port event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-PORT_MODE_EVENT_STATUS Format: %s %s.Explanation ACL portmode event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-RUNTIME_STATUS Format: %s %dExplanation ACL runtime status is reported as [chars] [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-SPAN_DEST_CONFIG_STATUS Format: %s %s.Explanation ACL SPAN destination config event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-SPAN_SRC_CONFIG_STATUS Format: %s %s.Explanation ACL SPAN source configuration event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-STATUS Format: ACL Status: %s.Explanation ACL status is reported as [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL-6-UPDATE_SSRAM_QOS_EVENT_STATUS Format: %s %s.Explanation ACL update SSRAM for QoS event status is reported as [chars] [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL_TCAM Messages
This section contains the ACL_TCAM messages.
ACL_TCAM-2
Error Message ACL_TCAM-2-CONFIG_READ_FROM_DRIVER_FAILED Format: %s %dExplanation The system is unable to read the configuration from the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-CONFIG_WRITE_TO_DRIVER_FAILED Format: %s %dExplanation The system is unable to write the configuration to the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-INCONSISTENT_DATABASE Format: Database found inconsistent.Explanation Database found inconsistent.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-INCONSISTENT_TCAM_CONTENTS Format: TCAM contents found inconsistent.Explanation TCAM contents are found inconsistent.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-INIT_FAILED Format: Initialization failed for forwarding engine ASIC: %dExplanation Initialization failed for the forwarding engine ASIC [dec], in [chars] TCAM.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-INIT_REGIONS_FAILED Format: Initialization failed for forwarding engine ASIC: %dExplanation Initialization of regions failed for the forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-MTS_FAILURE Format: MTS operation failed: %s.Explanation MTS operation failed. [chars] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-MTS_REGISTRATION_FAILED Format: MTS registration failed for opCode: %d.Explanation MTS registration failed for opCode: [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-NO_TCAM_LEFT Format: ACLTCAM resource exhausted for interface : %sExplanation ACLTCAM hardware resource is completely used.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-PSS_FAILURE Format: Failed to do PSS operation: %sExplanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-PSS_OPEN_FAILED Format: PSS open failed - %x.Explanation Persistent database handle could not be obtained for ACLTCAM. [hex] is the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-2-RECONS_FAILED Format: Reconstruction of TCAM contents failed during upgrade - %x.Explanation During nondisruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL_TCAM-3
Error Message ACL_TCAM-3-REGISTER_FAILED Format: Could not register to MTS opcode %s - error %x.Explanation ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL_TCAM-4
Error Message ACL_TCAM-4-FLOW_COUNTER_INVALIDATED Format: Flow counter for flow: vsan: %dExplanation ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [%s].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACL_TCAM-4-FLOW_COUNTER_VALIDATED Format: Flow counter for flow: vsan: %dExplanation ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACL_TCAM-6
Error Message ACL_TCAM-6-STATUS Format: Status: %s.Explanation ACLTCAM status is reported as: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLLOG Messages
This section contains the ACLLOG messages.
ACLLOG-4
Error Message ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars]Explanation The maximum flow has been reached in current interval: [chars].
Recommended Action No action is required.
Error Message ACLLOG-4-ACLLOG_THRESHOLD: [chars]Explanation Threshold Reached for Flow: [chars].
Recommended Action No action is required.
Error Message ACLLOG-4-MAXFLOW_REACHED Format: %sExplanation The maximum flow has been reached in current interval: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLLOG-4-THRESHOLD Format: %sExplanation Threshold Reached for Flow: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLLOG-6
Error Message ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars]Explanation Flow informationin current alert interval: [chars].
Recommended Action No action is required.
Error Message ACLLOG-6-ACLLOG_NEW_FLOW: [chars]Explanation New Acllog Flow: [chars].
Recommended Action No action is required.
Error Message ACLLOG-6-FLOW_INTERVAL Format: %sExplanation Flow informationin current alert interval: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLLOG-6-NEW_FLOW Format: %sExplanation New Acllog Flow: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLMGR Messages
This section contains the ACLMGR messages.
ACLMGR-2
Error Message ACLMGR-2-ACLMGR_COMMIT_FAIL: Commit failed: client %llX, [chars]Explanation The PPF commit failed.
Recommended Action No action is required.
Error Message ACLMGR-2-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], session 0x%llx, type: [chars]Explanation ACL PPF database lock acquire/release related message.
Recommended Action No action is required.
Error Message ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on interface [chars] ([hex]) allowed to succeed in spite of access-list failureExplanation Although an access-list operation failed during a port event, the port event still finished successfully because errordisable is disallowed.
Recommended Action No action is required.
Error Message ACLMGR-2-COMMIT_FAIL Format: Commit failed: client %llXExplanation The PPF commit failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-EXITING: Exit reason: [chars]Explanation The ACLMGR service process has exited due to [char]. The process has probably been restarted automatically.
Recommended Action No action is required.
Error Message ACLMGR-2-INITFAIL Format: ACLMGR Service Init failed: %sExplanation ACLMGR Service initialization failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-INITFAIL: ACLMGR Service Init failed: [chars]Explanation ACLMGR Service initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message ACLMGR-2-MALLOC_ERROR Format: Size %d bytesExplanation The ACLMGR service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-MALLOC_ERROR: Size [dec] bytesExplanation The ACLMGR service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-PSS_ERROR Format: %s: PSS ret. val=%dExplanation The ACLMGR service encountered an error while operating on a persistent storage database.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-PSS_ERROR: [chars]: PSS ret. val=[dec]Explanation The ACLMGR service encountered an error while operating on a persistent storage database.
Recommended Action No action is required.
ACLMGR-3
Error Message ACLMGR-3-ACLMGR_ACL_ON_FAB_INACTIVE: ACL on FEX fabric interface not activatedExplanation ACL applied to a FEX fabric port or port channel is not activated.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel bound interface not activatedExplanation ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric port channel.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], session 0x%llx, type: [chars]Explanation ACL PPF database lock acquire/release related message.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars]Explanation The PPF generated an error.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found corruptedExplanation The ACLMGR service has detected a corrupted file in its persistent information databases The database would be recreated.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL statistic parsing or consolidation failedExplanation A statistic update failed during the parsing or consolidation step; statistics may have been lost.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection to interface [chars] ([hex]) disabled: the port has been removedExplanation A VACL redirection to the port has been deactivated because the port has been removed.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed: client %llX, [chars]Explanation The PPF Verify failed.
Recommended Action No action is required.
Error Message ACLMGR-3-DB_LOCK_MSG Format: ACL database messageExplanation ACL PPF database lock acquire/release related message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-3-MTSERROR Format: %sExplanation ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-3-MTSERROR: [chars]Explanation ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message ACLMGR-3-PPF_ERROR Format: PPF error: %sExplanation The PPF generated an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-3-STAT_CONSOLIDATION_FAILURE Format: ACL statistic parsing or consolidation failedExplanation A statistic update failed during the parsing or consolidation step; statistics may have been lost.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-3-VERIFY_FAIL Format: Verify failed: client %llXExplanation The PPF Verify failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLMGR-4
Error Message ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning: [chars]Explanation The PPF generated warning.
Recommended Action No action is required.
Error Message ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to interface [chars] ([hex]) disabled: the port became a portchannel memberExplanation A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel.
Recommended Action No action is required.
Error Message ACLMGR-4-PPF_WARNING Format: PPF warning: %sExplanation The PPF generated warning.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-4-PSS_VERSION_MISMATCH Format: PSS %d Code %dExplanation There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]Explanation There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action No action is required.
ACLMGR-6
Error Message ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification: [chars]Explanation The PPF generated a notification.
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_ACTIVE Format: Became ACTIVE from standby modeExplanation The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby modeExplanation The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_STDBY Format: Became STANDBY from active modeExplanation The ACLMGR service became standby from active mode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-BECAME_STDBY: Became STANDBY from active modeExplanation The ACLMGR service became standby from active mode.
Recommended Action No action is required.
Error Message ACLMGR-6-FAILED_TO_SEND_HEARTBEAT Format: Failed to send heartbeat to system manager: Reason=%sExplanation The ACLMGR service was unable to send heartbeats to the system manager.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]Explanation The ACLMGR service was unable to send heartbeats to the system manager.
Recommended Action No action is required.
Error Message ACLMGR-6-PPF_NOTIF Format: PPF notification: %sExplanation The PPF generated a notification.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-SERVICE_UP: Initialized [chars]Explanation The ACLMGR service is up and ready The service was initialized in [char] mode.
Recommended Action No action is required.
Error Message ACLMGR-6-SRVEXIT Format: ACLMGR Service shutting down gracefullyExplanation ACLMGR Service is shutting down gracefully.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-SRVEXIT: ACLMGR Service shutting down gracefullyExplanation ACLMGR Service is shutting down gracefully.
Recommended Action No action is required.
Error Message ACLMGR-6-SWITCHOVER Format: Switching Over to other Sup.Explanation The ACLMGR service has successfully switched over to the standby supervisor module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-6-SWITCHOVER: Switching Over to other Sup.Explanation The ACLMGR service has successfully switched over to the standby supervisor module.
Recommended Action No action is required.
ACLQOS-SLOT# Messages
This section contains the ACLQOS-SLOT# messages.
ACLQOS-SLOT#-2
Error Message ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure: [chars]Explanation ACLQOS operation failed in the aclqos client.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE: Inband interface lif lookup failed ([chars])Explanation Inband interface lif lookup failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory allocation failed. [chars]Explanation Memory allocation failed. This is a critical failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource exhausted: [chars]Explanation TCAM resources to program acls exhausted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-PPF_FAILED: Database failure: [chars]Explanation Database operation failed in the aclqos client.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-3
Error Message ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control parametersExplanation Invalid Congestion Control parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control parameters: [chars]Explanation Invalid Congestion Control parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_MCM_ERROR: MCM Message Inconsistent. Please collect MCM and ACLMgr Tech Support for all VDCsExplanation MCM Message Inconsistent.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parametersExplanation Invalid Pause parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parameters: [chars]Explanation Invalid Pause parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS queuing error: [chars]Explanation Internal error in ACL/QoS queing configuration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-4
Error Message ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars]Explanation TCAM will be overused, turn off atomic update.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_MATCH_ALL_MERGE_UPDATE: Warning (match_all merging): [chars]Explanation Warning (match_all merging).
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Tcam [dec] Bank [dec]'s usage has reached its thresholdExplanation TCAM is almost full.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID: ACL/QoS invalid queuing policy because of cos map change: [chars] queue [chars], interface [chars]Explanation Attemped to configure an invalid queuing policy.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS invalid queuing policy: [chars]Explanation Attemped to configure an invalid queuing policy.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec] Bank [dec]'s usage is below the threshold nowExplanation TCAM's usage is below the threshold.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_WARNING: ACLQOS Warning: [chars]Explanation ACLQOS Warnings.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-5
Error Message ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE: Disruptive update of IPv6 compression entriesExplanation Disruptive IPv6 compression entries update.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic ACL/QoS policy update done for [chars]Explanation Nonatomic ACL/QoS policy update was done.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLTCAM Messages
This section contains the ACLTCAM messages.
ACLTCAM-2
Error Message ACLTCAM-2-ACL_TCAM_ADJ_EXHAUSTED: ACLTCAM failed to program route for VSAN: [dec], SID: [chars] DID: [chars], error: [chars].Explanation ACLTCAM process experienced a failure while programming route for VSAN [dec] SID [chars] DID [chars] due to resource exhaustion. [chars] is the error code.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to FULL. [chars] TCAM Usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED: [chars] [dec], Error: [hex].Explanation The system is unable to read the configuration from the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED: [chars] [dec], Error: [hex].Explanation The system is unable to write the configuration to the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_FLOW_STATS_READ_FAILED: Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).Explanation Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found inconsistent.Explanation Database found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found inconsistent.Explanation TCAM contents are found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM.Explanation Initialization failed for the forwarding engine ASIC [dec], in [chars] TCAM.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM, [chars] Region.Explanation Initialization of regions failed for the forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory allocation failed for size [dec].Explanation Memory allocation is failed for size [dec] bytes.
Recommended Action Restart the process.
Error Message ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars].Explanation MTS operation failed. [chars] is the reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed for opCode: [dec].Explanation MTS registration failed for opCode: [dec].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get route for VSAN: [dec], Rewrite: [chars] DID: [chars] DID MASK: [chars], error: [hex].Explanation ACLTCAM process experienced a failure while getting route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars]. [hex] is the error code.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource exhausted for interface : [chars]Explanation ACLTCAM hardware resource is completely used.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).Explanation [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID: Invalid([chars], value: [dec]) TCAM entry read from hardware TCAM (FWD-Engine: [dec], [chars] TCAM, Address: [dec]), Ignoring this entry.Explanation Invalid([chars], value: [dec]) TCAM entry from hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec]) Ignoring this entry.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).Explanation [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].Explanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed - [hex].Explanation Persistent database handle could not be obtained for ACLTCAM. [hex] is the error.
Recommended Action No action is required.
Error Message ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM contents failed during upgrade - [hex].Explanation During nondisruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.
Recommended Action No action is required.
ACLTCAM-3
Error Message ACLTCAM-3-REGISTER_FAILED: Could not register to MTS opcode [chars] - error [hex].Explanation ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.
Recommended Action No action is required.
ACLTCAM-4
Error Message ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) fell below [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] fell below [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] with statistics: frames = %llu & bytes = %llu was invalidated due to: [chars]Explanation ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [[chars]].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] is now validExplanation ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].
Recommended Action No action is required.
ACLTCAM-6
Error Message ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars].Explanation ACLTCAM status is reported as: [chars].
Recommended Action No action is required.
AM Messages
This section contains the AM messages.
AM-2
Error Message AM-2-API_INIT Format: Failed to initialize %s APIExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-BAD_TIMER Format: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-CLI_INIT Format: Failed to initialize CLIExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-INIT_FAIL Format: Initialization failureExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MQ_OPEN Format: Failed to open message queue %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_BIND Format: Failed to do mts_bind for %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_OPC_SET Format: Failed to register with opcode %d: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_RECV Format: MTS queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_SADDR_GET Format: Failed to get source of mts queue %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-NO_WORKBIT Format: Failed to register %s too many notify clientsExplanation An unexpected fatal error has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-2-REQD_COMP_DOWN Format: Required component \%s\ has gone down.Explanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-REQD_COMP_FAIL Format: Required component \%s\ has failed to initialize.Explanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_CREAT Format: Failed to create shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_DESTROY Format: Failed to destroy shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_OPEN Format: Failed to open shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SET_SCHED Format: Failed to set policy or priorityExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SHM_CREAT Format: Failed to create shared memory: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SHM_LOCK_CREAT Format: Failed to create shared memory lock: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SVR_REG Format: Failed to register as a client of %s for VRF %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_NAME Format: Failed to get name from sysmgr during %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-THR_CREAT Format: Failed to create thread %s: error %dExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-THREAD_FAIL Format: Failed to start %s threadExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-URIB_PIB Format: Unable to get pib for %s VRF from URIBExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
AM-3
Error Message AM-3-BAD_PARAMS Format: Called %s with address family %d, iod %d, l3address %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-DEL_PROT_ADJ Format: Unable to delete protocol adjacency for %s, uuid %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-IF_INDEX Format: Invalid interface index received from %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-IP_GLEAN_EXCESS_TRAFFIC Format: Excess traffic (%llu packets / %llu octets) were dropped in %s seconds for ungleaned prefix %s/32 on interface %s in vrf %sExplanation This message indicates an informational log about a system event.
Recommended Action No action is required.
Error Message AM-3-MAC_REG_FAILED Format: Mac registration with L2FM failed for mac %s, iod %s, phy iod: %sExplanation MAC registration with L2FM failed.
Recommended Action No action is required.
Error Message AM-3-MAX_RETRIES Format: Notification retry limit exceeded for %sExplanation Client is not replying to our notifications.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-MQ_RECV Format: Message queue receive failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MQ_SEND Format: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MSG_TO_TLV Format: Notification message to TLV failedExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MTS_DROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MTS_SEND Format: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_AF Format: %s: Unable to get address family block for index %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_MEM Format: Malloc failed for %s %sExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-NO_PIB Format: Unable to get pib for client pid %d while processing %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_SMEM Format: Smalloc failed for %s %sExplanation AM's shared memory quota may be used up, due to a large number of adjacencies or a memory leak.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-PT_ADD Format: Pt_add failed for %s %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-QUEUE Format: %s failed for %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-READ_LOCK_HOLD Format: %s:%s():%d: Assert, read-lock not acquiredExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-RIB_RTE_CHG Format: Failed to send AM route changes to %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-THR_MUTEX_LOCK Format: Failed to thread mutex lockExplanation Failed function pthread_mutex_lock.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-3-THR_MUTEX_UNLOCK Format: Failed to thread mutex lockExplanation Failed function pthread_mutex_unlock.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-3-TLV_TO_STRUCT Format: Notification TLV to struct failedExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-URIB_CNTXT Format: Failed to get %s VRF from URIBExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
AM-5
Error Message AM-5-INVALID_NOTIFY Format: Received invalid notification messageExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_MAJOR Format: Received unknown major message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_MINOR Format: Received unknown minor message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MSG_UNK Format: Received unknown % type: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MTS_OPC_UNK Format: Received unknown MTS opcode %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-REG_DELAY Format: AM register %s delay: %d secondsExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
AM-6
Error Message AM-6-FAILED_STATS Format: Failed to retrieve stats from FTMExplanation This message indicates an informational log about a system event.
Recommended Action No action is required.
Error Message AM-6-SYSMAN_CLEANUP Format: Terminated by SYSMAN cleanup signal ; Explanation: Informational log about a system event.Explanation The system has detected an error.
Recommended Action No action is required.
AMM-SLOT# Messages
This section contains the AMM-SLOT# messages.
AMM-SLOT#-0
Error Message AMM-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed!Explanation AMM failed to initialize CLI infrastructure\sbackendlibrary.Thisisafatalerror.'
Recommended Action No action is required.
Error Message AMM-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization failed!Explanation AMM failed to initialize timer library. This is a fatal error.
Recommended Action No action is required.
AMM-SLOT#-2
Error Message AMM-SLOT#-2-AMM_MEM_ALLOC: Memory allocation failed. [chars]Explanation Memory allocation failed. This is a critical failure.
Recommended Action No action is required.
Error Message AMM-SLOT#-2-AMM_RECOVERY_ERROR: Error in Recovery: [chars]Explanation AMM failed to recover after a re-start. This is a fatal error.
Recommended Action No action is required.
AMM-SLOT#-6
Error Message AMM-SLOT#-6-INITIALIZED: Internal state created [chars]Explanation AMM has created its internal state stateless/stateful [chars].
Recommended Action No action is required.
AMT Messages
This section contains the AMT messages.
AMT-2
Error Message AMT-2-SHM_LOCK_CREAT Format: Failed to create shared memory lock: %sExplanation The system has failed to initialize.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
AMT-3
Error Message AMT-3-AMT_INIT Format: AMT init failed: %sExplanation AMT process initialization failed.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-API_INIT Format: Couldn't initialize %s APIExplanation AMT failed to open API to interact with the component.
Recommended Action No action is required.
Error Message AMT-3-BIND Format: bind() on %s failed: %sExplanation AMT failed to bind UDP socket.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-COMP_DEREG Format: Unable to de-register with %sExplanation AMT failed to de-register with a server component.
Recommended Action No action is required.
Error Message AMT-3-COMP_REG Format: Unable to register with %sExplanation AMT failed to register with a server component.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-DISC_NOT_ANYCAST Format: Relay Discovery packet from %s is addressed to %s, not an anycast addressExplanation An AMT Gateway sent Relay Discovery not using the Relay Anycast address.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-IP_TUNNEL_LIMIT Format: Reach IP tunnel limit of %dExplanation AMT process failed to create tunnel because the policy limit has been reached.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-IPV6_TUNNEL_LIMIT Format: Reach IPv6 tunnel limit of %dExplanation AMT process failed to create tunnel because the policy limit has been reached.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-LIB_API_INIT Format: Couldn't initialize %s APIExplanation Failed to open AMT API to interact with the component.
Recommended Action No action is required.
Error Message AMT-3-LIB_SM_OPEN Format: Couldn't open shm segment %sExplanation Process failed to access AMT's shared memory.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-MALLOC Format: Private mem malloc (%lu) failed in %sExplanation AMT process is out of free private memory.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-MRIB_ADD_ROUTE Format: MRIB add route failed in %sExplanation AMT failed to add route in MRIB.
Recommended Action No action is required.
Error Message AMT-3-MRIB_DEL_ROUTE Format: MRIB delete route failed in %sExplanation AMT failed to delete route in MRIB.
Recommended Action No action is required.
Error Message AMT-3-MTS_DROP Format: Error returned from mts_drop(), errno: %sExplanation AMT called an MTS API which returned an error.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-MTS_RECV Format: Error returned from mts_recv(), errno: %sExplanation AMT called an MTS API which returned an error.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-NO_AMT_PAYLOAD Format: No AMT payload after stripping IP/IPv6 and UDP headers from %s, length: %dExplanation AMT process received packet which is too short. The other side of the AMT tunnel has a protocol error.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-NO_M_COPYBACK Format: m_copyack() failed in amt_receive_multicast_data()Explanation AMT process failed to copy AMT multicast data into an mbuf for IP to replicate the packet.
Recommended Action No action is required.
Error Message AMT-3-NO_M_GET Format: amt_receive_multicast_data() could allocate mbuf data structureExplanation AMT process failed to allocate an mbuf data structure to forward AMT encapsulated data in an AMT Gateway.
Recommended Action No action is required.
Error Message AMT-3-NO_SET_PRIORITY Format: Failed to set policy or priorityExplanation AMT process could not set itself process priority, exiting.
Recommended Action No action is required.
Error Message AMT-3-PKT_BAD_NONCE Format: Nonce from Relay Advertisement packet from %s does not match Relay Discovery packet nonce, received 0x%08x, expected 0x%08xExplanation There is a possible AMT spoof attack since the Advertise and Disocvery nonces do not match.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-PKT_TOO_SHORT Format: Packet too short from %sExplanation AMT process received packet which is too short. The other side of the AMT tunnel has a protocol error.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-PT_ADD Format: Couldn't add %s to Patricia TrieExplanation AMT failed to update the tunnel Patricia Trie.
Recommended Action No action is required.
Error Message AMT-3-PT_DEL Format: Couldn't delete %s from local PTExplanation AMT failed to delete the local route-table entry.
Recommended Action No action is required.
Error Message AMT-3-PTHREAD_CREATE Format: Couldn't create thread %sExplanation AMT process failed to create a task thread.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-RESTART_REASON Format: AMT process has restarted, restart reason: %s\nExplanation AMT is restoring the routes it had added in previous instance.
Recommended Action No action is required.
Error Message AMT-3-RLIMIT Format: Couldn't set AMT data segment size to %luExplanation AMT process could not set a memory resource limit, exiting.
Recommended Action No action is required.
Error Message AMT-3-SETSOCKOPT Format: setsockopt() on %s failed: %sExplanation AMT failed in UDP socket operation.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-SLAB_CREATE Format: Slab alloc of type %s failedExplanation AMT process failed to allocate Slab memory.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-SM_CREATE Format: Couldn't create shm segment %sExplanation AMT process failed to initialize shared memory resource.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-SMALLOC Format: Shared mem malloc (%lu) failed in %sExplanation AMT process is out of free shared memory.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-SOCKET Format: socket() for %s failed: %sExplanation AMT failed to obtain UDP socket.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-TIMER_SET_INIT Format: Couldn't init %s active timer setExplanation AMT failed to initialize timer resource.
Recommended Action Dump core, and then restart component.
Error Message AMT-3-TUNNEL_FAILED Format: Could not allocate shared-memory for amt_tunneltype data structureExplanation AMT process failed to create data structure to establish tunnel.
Recommended Action Configure the network or router to decrease the number of routes.
Error Message AMT-3-UDP_SENDTO Format: udp_sendto() failed to %s in %s, error: %sExplanation AMT failed to send over UDP socket.
Recommended Action No action is required.
Error Message AMT-3-UNKNOWN_MTYPE Format: Unknown mtype: %d/%d in %sExplanation AMT process received unknown Interprocess message, dropped.
Recommended Action No action is required.
AMT-6
Error Message AMT-6-RESTART_SHUTDOWN Format: AMT shutting self down via restart commandExplanation AMT process is shutting itself down due to the restart command.
Recommended Action No action is required.
Error Message AMT-6-SHUTDOWN Format: Shutting down AMT processExplanation PIM received a shutdown request.
Recommended Action No action is required.
Error Message AMT-6-SHUTDOWN_SELF Format: AMT shutting self downExplanation AMT process is shutting itself down.
Recommended Action No action is required.
Error Message AMT-6-UNKNOWN_OPC Format: Received unknown mts opcode %dExplanation AMT process received unknown Interprocess message, dropped.
Recommended Action No action is required.
ARP Messages
This section contains the ARP messages.
ARP-2
Error Message ARP-2-AM_PIB Format: Failed to acquire AM handle %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-AM_REG Format: Failed to register as a client of AM %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-API_INIT Format: Failed to initialize %s APIExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-API_INITIALIZE Format: Failed to initialize %s API with rc=0x%x, %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-CLI_INIT Format: Failed to initialize CLIExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-DUP_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-2-DUP_SRCIP Format: Source address of packet received from %s on %s is duplicate of local, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-2-INIT_FAIL Format: Initialization failureExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MQ_OPEN Format: Failed to open message queue %s: %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MQ_RECV Format: Message queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MTS_BIND Format: Failed to do mts_bind for %s: %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MTS_OPC_SET Format: Failed to register with opcode %d: %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MTS_RECV Format: MTS queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SET_SCHED Format: Failed to set policy or priorityExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SHM_ATTACH Format: Failed to attach %s shared memoryExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SVR_REG Format: Failed to register as a client of %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-THR_CREAT Format: Failed to create thread %s: error %dExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-THREAD_FAIL Format: Failed to start %s threadExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-TIMER_SET Format: Failed to initialize new timer setExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-TIMERS_INIT Format: Failed to initialize timersExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
ARP-3
Error Message ARP-3-ADJ_ADD Format: Failed to add adjacency for received packet from %s on %sExplanation Due to this failure, packet forwarding to this address will be affected until the next successful retry.
Recommended Action No action is required.
Error Message ARP-3-ADJ_UPD Format: Failed to update adjacency for received packet from %s on %sExplanation Due to this failure, packet forwarding will continue to use the existing ARP adjacency entry values.
Recommended Action No action is required.
Error Message ARP-3-API_MQ_INVAL Format: ARP API Error: Invalid ARP message queue in %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MQ_SEND Format: ARP API Error: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MTS_INVAL Format: ARP API Error: Invalid ARP MTS queue in %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MTS_SEND Format: ARP API Error: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-DAI_FETCH_ERR Format: DAI lookup failed, callback function returned 0x%x (%s) for %s %sExplanation DAI lookup failed.
Recommended Action No action is required.
Error Message ARP-3-DUP_VADDR_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VADDR_SRCIP Format: Source address of packet received from %s on %s is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VIRT_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VIRT_SRCIP Format: Source address of packet received from %s on %s is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-GRAT_ETH Format: Sending gratuitous arp for %s on invalid interface %s, not ethernetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_IOD Format: Sending gratuitous ARP for %s on an invalid interface %uExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_IP Format: Sending gratuitous ARP request for %s IP address %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_NON_AM Format: Sending gratuitous arp for %s on invalid interface %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_P2P Format: Sending gratuitous arp for %s on invalid interface %s, point-to-pointExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_ERR Format: Failed to get ARP header, expected %d, got %d bytesExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_L2LEN_ERR Format: Received packet with incorrect layer 2 address length (%d bytes)Explanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_L3LEN_ERR Format: Received packet with incorrect layer 3 address length (%d bytes)Explanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-IF_INDEX Format: Invalid interface index received from %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-INVAL_HDR Format: Found incorrect hardware/protocol type in ARP header: %hu/%huExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-INVAL_STATE Format: Unrecognized ARP entry state in timer callback: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MAC_ERR Format: Failed to get MAC address on %s for %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MBUF_ERR Format: Failed to get the remainder of packet, expected %d, got %d bytesExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MTS_DROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-NO_MBUF Format: Failed to allocate buffer for %sExplanation The system may have run out of packet memory buffers.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ARP-3-NO_MEM Format: Malloc failed for %s %sExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ARP-3-PKT_ENCAP Format: Failed to encapsulate packetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-PKT_OUT Format: Failed to send packet to PMExplanation PM's message queue may be temporarily full.
Recommended Action No action is required.
Error Message ARP-3-REQ_ADD Format: Failed to add adjacency while sending request for %s on %s, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_ETH Format: Sending ARP request for %s on invalid interface %s, not ethernet, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_IOD Format: Sending ARP request for %s on an invalid interface %u, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_IP Format: Sending ARP request for %s IP address %s on %s, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_NON_AM Format: Sending ARP request for %s on invalid interface %s request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_P2P Format: Sending ARP request for %s on invalid interface %s, point-to-point, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-TIMER_RSTART Format: Failed to restart timer 0x%p for %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_ETH Format: Adding vrrp arp for %s: invalid interface %s, not ethernetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_IOD Format: Adding vrrp arp for %s: invalid interface %uExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_NON_AM Format: Sending vrrp arp for %s on invalid interface %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_P2P Format: Sending vrrp arp for %s on invalid interface %s, point-to-pointExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRPQ_ADD Format: Failed to add VRRP queue entry for %s, %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRPQ_IP Format: Trying to add invalid IP address %s on %s to vrrp queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
ARP-4
Error Message ARP-4-DIR_BCAST Format: %s address of packet received from %s on %s matches directed broadcast address, %sExplanation There may be a configured subnet mask-length mismatch among router interfaces connected on this LAN.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-DUP_IP Format: ARP entry found with duplicate IP address %s on %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-INVAL_IP Format: Received packet with invalid %s IP address (%s) from %s on %sExplanation There may be a connected router sending packets with a bogus IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-INVAL_MAC Format: Received packet with invalid %s MAC address (%s) from %s on %sExplanation There may be a connected router sending packets with a bogus MAC address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-OWN_SRCMAC Format: Received packet with a local source MAC address (%s) from %s on %sExplanation There may be a connected router sending packets with local MAC address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-SRCIP_ERR Format: Source address of received packet (%s) does not match subnet on interface %sExplanation There may be a configured subnet mismatch among router interfaces connected on the LAN.
Recommended Action Check all routers on the interface for a misconfiguration.
ARP-5
Error Message ARP-5-MQ_MINOR Format: Received unknown minor message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MSG_UNK Format: Received unknown % type: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MTS_OPC_UNK Format: Received unknown MTS opcode %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_IP_NOTIF Format: Unrecognized IP address change notification type %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_MSG_MINOR Format: Unrecognized %s message minor type %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_SIG Format: Received unknown signal %d ; Explanation: An unexpected but recoverable error has occurred.Explanation The system has detected an error.
Recommended Action No action is required.
ASCII-CFG Messages
This section contains the ASCII-CFG messages.
ASCII-CFG-2
Error Message ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while Ascii configuration was being applied. Please use show startup-config log to view detailsExplanation At least one command failed while the ASCII configuration was being applied.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_LIB_INVOKE_ERR: Ascii config library invocation error: [chars]Explanation The system has encountered an error while the library function was being invoked to display the ASCII configuration.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_OPER_FAIL: Operation failed because of [chars]Explanation Operation failed.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_ROLLBACK_FAILED: Rollback to checkpoint [chars] Failed, Going to undo the changes (atomic option)Explanation Rollback operation failed for atomic option.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_ROLLBACK_UNDO_FAILED: Undo failed for atomic Rollback, Please correct the error manually and retry rollbackExplanation The system has encountered an error while undoing the rollback changes (for atomic behavior.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_SYSLOG_INIT_FAILED: Ascii config Syslog Init ErrorExplanation The system has encountered an error while initializing the syslog for the ASCII configuration.
Recommended Action No action is required.
Error Message ASCII-CFG-2-PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec]Explanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ASCII-CFG-3
Error Message ASCII-CFG-3-ACFG_MTSERROR: [chars]Explanation Ascii-cfg-server (rollback process) encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
ASCII-CFG-6
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE: cleared all the configuration checkpointsExplanation The system has cleared all the configuration checkpoints.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: Created configuration checkpoint [chars]Explanation The system has created a configuration checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: Deleted configuration checkpoint [chars]Explanation The system has deleted the configuration checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_MAX_CHECKPOINTS: Maximum no of checpoints reached, Removing the oldest checkpointExplanation The system detects that the maximum number of checkpoints has been reached and has removed the oldest checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback to checkpoint [chars] (with atomic option)Explanation The system will perform a configuration rollback with the atomic option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback to checkpoint [chars] (with best-effort option)Explanation The system will perform a configuration rollback with the best-effort option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration rollback to checkpoint [chars] (with stop-at-first failure option)Explanation The system will perform a configuration rollback with the stop-at-first-failure option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-INFORMATION: [chars]Explanation An event happened that affects Acfg-Rollback. [chars] indicates the event.
Recommended Action No action is required.
Error Message ASCII-CFG-6-PSS_ERR: [chars]Explanation An error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ASCII_CFG Messages
This section contains the ASCII_CFG messages.
ASCII_CFG-2
Error Message ASCII_CFG-2-ACFG_CONFIGURATION_APPLY_ERROR Format: Error encountered while Ascii configuration was being applied. Please use show startup-config log to view detailsExplanation At least one command failed while the ASCII configuration was being applied.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-2-ACFG_LIB_INVOKE_ERR Format: Ascii config library invocation error: %sExplanation The system has encountered an error while the library function was being invoked to display the ASCII configuration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-2-ACFG_OPER_FAIL Format: Operation failed because of %sExplanation operation failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-2-ACFG_SYSLOG_INIT_FAILED Format: Ascii config Syslog Init ErrorExplanation The system has encountered an error while initializing the syslog for the ASCII configuration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-2-PSS_VER_FAIL Format: PSS file %s has version %d.%d.%dExplanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ASCII_CFG-6
Error Message ASCII_CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE Format: cleared all the configuration checkpointsExplanation cleared all the configuration checkpoints.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-6-ACFG_CHECKPOINT_CREATED Format: Created configuration checkpoint %sExplanation created configuration checkpoint.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-6-ACFG_CHECKPOINT_DELETED Format: Deleted configuration checkpoint %sExplanation deleted configuration checkpoint.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-6-ACFG_MAX_CHECKPOINTS Format: Maximum no of checpoints reachedExplanation The system detects that the maximum number of checkpoints has been reached and has removed the oldest checkpoint.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-6-INFORMATION Format: %sExplanation an event happened that affects Acfg-Rollback. [chars] indicates the event.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII_CFG-6-PSS_ERR Format: %sExplanation an error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ASSOC_MGR Messages
This section contains the ASSOC_MGR messages.
ASSOC_MGR-0
Error Message ASSOC_MGR-0-EMERGENCY_MSG Format: %sExplanation Association Manager Emergency Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-0-EMERGENCY_MSG: [chars]Explanation Association Manager Emergency Message.
Recommended Action Please file the bug for Association Manager Component thro' CDETS.
ASSOC_MGR-1
Error Message ASSOC_MGR-1-ALERT_MSG Format: %sExplanation Association Manager Alert Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-1-ALERT_MSG: [chars]Explanation Association Manager Alert Message.
Recommended Action Association Manager Internal Operation Alert.
ASSOC_MGR-2
Error Message ASSOC_MGR-2-CRITICAL_MSG Format: %sExplanation Association Manager Critical Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-2-CRITICAL_MSG: [chars]Explanation Association Manager Critical Message.
Recommended Action No action is required.
ASSOC_MGR-3
Error Message ASSOC_MGR-3-ERROR_MSG Format: %sExplanation Association Manager Error Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-3-ERROR_MSG: [chars]Explanation Association Manager Error Message.
Recommended Action No action is required.
ASSOC_MGR-4
Error Message ASSOC_MGR-4-WARN_MSG Format: %sExplanation Association Manager Warning Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-4-WARN_MSG: [chars]Explanation Association Manager Warning Message.
Recommended Action No action is required.
ASSOC_MGR-5
Error Message ASSOC_MGR-5-NOTIF_MSG Format: %sExplanation Association Manager Notification Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-5-NOTIF_MSG: [chars]Explanation Association Manager Notification Message.
Recommended Action No action is required.
ASSOC_MGR-6
Error Message ASSOC_MGR-6-ASSOC_ACTIVATED Format: Association Activated for vlan id:%d <--> vsan id:%dExplanation Association Activated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-ASSOC_ACTIVATED: Association Activated for vlan id:[dec] <--> vsan id:[dec]Explanation Association Activated.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_CREATED Format: Association Created for vlan id:%d <--> vsan id:%dExplanation Association Created.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-ASSOC_CREATED: Association Created for vlan id:[dec] <--> vsan id:[dec]Explanation Association Created.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_DEACTIVATED Format: Association Deactivated for vlan id: %d <--> vsan id: %dExplanation Association Deactivated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-ASSOC_DEACTIVATED: Association Deactivated for vlan id: [dec] <--> vsan id: [dec]Explanation Association Deactivated.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_DELETED Format: Association Deleted for vlan id: %d <--> vsan id: %dExplanation Association Deleted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-ASSOC_DELETED: Association Deleted for vlan id: [dec] <--> vsan id: [dec]Explanation Association Deleted.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_MGR_STATEFULL_RESTART: Association Manager Statefull RestartExplanation Association Manager Stateful Restart.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_MGR_STATELESS_RESTART: Association Manager Stateless RestartExplanation Association Manager Stateless Restart.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG Format: Association status for vlan id: %d <--> vsan id: %d changed from %s to %sExplanation Association Operational State Change.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG: Association status for vlan id: [dec] <--> vsan id: [dec] changed from [chars] to [chars]Explanation Association Operational State Change.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-INFO_MSG Format: %sExplanation ASSOC Manager Informational Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-INFO_MSG: [chars]Explanation ASSOC Manager Informational Message.
Recommended Action No action is required.
Error Message ASSOC_MGR-6-STATEFULL_RESTART Format: Association Manager Statefull RestartExplanation Association Manager Stateful Restart.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-6-STATELESS_RESTART Format: Association Manager Stateless RestartExplanation Association Manager Stateless Restart.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ASSOC_MGR-7
Error Message ASSOC_MGR-7-DEBUG_MSG Format: %sExplanation Association Manager Debug Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASSOC_MGR-7-DEBUG_MSG: [chars]Explanation Association Manager Debug Message.
Recommended Action No action is required.
AVANTI_LS Messages
This section contains the AVANTI_LS messages.
AVANTI_LS-0
Error Message AVANTI_LS-0-NODE_EMERG_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-1
Error Message AVANTI_LS-1-NODE_ALERT_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-2
Error Message AVANTI_LS-2-NODE_CRIT_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-3
Error Message AVANTI_LS-3-NODE_ERR_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-4
Error Message AVANTI_LS-4-NODE_WARNING_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-5
Error Message AVANTI_LS-5-NODE_NOTICE_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-6
Error Message AVANTI_LS-6-NODE_INFO_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVANTI_LS-7
Error Message AVANTI_LS-7-NODE_DEBUG_MSG Format: %sExplanation Syslog message from a AVANTI_HELP_INTERFACEnode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVM Messages
This section contains the AVM messages.
AVM-2
Error Message AVM-2-SVC_SYSLOG_INIT_FAILED Format: Initialization failed for SVC: %sExplanation Initialization failed for SVC.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-2-SVC_SYSLOG_NO_PORT_CHAN Format: Too many PortChannels allocated by user for interface %sExplanation AVANTI_HELP_INTERFACEneeds port channels to operate. Too many PortChannels have been allocated by the user for the interface to operate correctly.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-2-SVC_SYSLOG_PATH_FAILURE Format: System health detected SVC packet path failure for %s.Explanation The CSM has been brought down by the system health monitor. System Health has detected a failure in the packet path between the SVC interface on the CSM and the backplane. This System Health test is run periodically.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-2-SVC_SYSLOG_URIFS_FAILURE Format: %s is unreachable for reason: %sExplanation AVANTI_HELP_INTERFACEmodflash is not accessible. Modflash is the name of the file system local to the SVC interface, and is typically used for coredumps and temporary file transfers.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVM-3
Error Message AVM-3-SVC_SYSLOG_IF_INTERNAL_ERROR Format: Interface %s internal error: %sExplanation AVANTI_HELP_INTERFACEinternal error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-3-SVC_SYSLOG_LC_INTERNAL_ERROR Format: Unable to send MTS to linecard in slot %d: %sExplanation Linecard MTS failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-3-SVC_SYSLOG_NPORT_INTERNAL_ERROR Format: %s N-port for Interface %sExplanation N-port internal error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVM-4
Error Message AVM-4-SVC_SYSLOG_IF_INTERNAL_WARN Format: Interface %s internal warning: %sExplanation AVANTI_HELP_INTERFACEinternal warning.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-4-SVC_SYSLOG_NPORT_INTERNAL_WARN Format: %s N-port for Interface %sExplanation AVANTI_HELP_INTERFACEinternal warning.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVM-5
Error Message AVM-5-SVC_SYSLOG_IF_CONFIG_DELETED Format: Interface %s configuration was deleted%sExplanation AVANTI_HELP_INTERFACEconfiguration was deleted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-5-SVC_SYSLOG_IF_DOWN Format: Interface %s is downExplanation AVANTI_HELP_INTERFACEis down.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-5-SVC_SYSLOG_IF_UP Format: Interface %s is upExplanation AVANTI_HELP_INTERFACEis up.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AVM-6
Error Message AVM-6-SVC_SYSLOG_CL_CONFIG Format: Node %s has become config node of cluster %sExplanation AVANTI_HELP_INTERFACEhas because cluster config node.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-6-SVC_SYSLOG_CL_JOIN Format: Node %s has joined cluster %sExplanation AVANTI_HELP_INTERFACEhas joined cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-6-SVC_SYSLOG_CL_UNJOIN Format: Node %s has left cluster %sExplanation AVANTI_HELP_INTERFACEhas left cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-6-SVC_SYSLOG_LC_WWN_PURGE Format: All WWNs for module %d have been purged%sExplanation AVANTI_HELP_LINECARDhas purged all WWNs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AVM-6-SVC_SYSLOG_VSAN_INACTIVE Format: Vsan %d suspendedExplanation VSAN was suspended; can cause warnings.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BELLAGIO2 Messages
This section contains the BELLAGIO2 messages.
BELLAGIO2-2
Error Message BELLAGIO2-2-CATASTROPHIC_FAILURE Format: Arbiter Catastrophic interrupt:%sExplanation Arbiter trigerrored Catastrophic error interrupt.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BELLAGIO2-2-MBIST_FAIL Format: Arbiter MBIST failed:%sExplanation Arbiter failed built in self test.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BFD Messages
This section contains the BFD messages.
BFD-3
Error Message BFD-3-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to missing ACL resources for interface [chars]Explanation BFD session [chars] failed due to missing ACL resources for interface [chars].
Recommended Action No action is required.
Error Message BFD-3-SESSION_ACL_INSTALL_GAVE_UP Format: BFD session %s installation failed due to ACL installation failure interface %sExplanation BFD session [chars] installation failed due to ACL installation failure interface [chars.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-3-SESSION_ACL_INSTALL_GAVE_UP: BFD session [chars] installation failed due to ACL installation failure interface [chars]Explanation BFD session [chars] installation failed due to ACL installation failure interface [chars.
Recommended Action Maximum acl install retries exceeded. Please to free up acl resources.
Error Message BFD-3-SESSION_ACL_REMOVE_GAVE_UP Format: BFD session %s removal failed due to ACL removal failure interface %sExplanation BFD session [chars] removal failed due to ACL removal failure interface [chars.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-3-SESSION_ACL_REMOVE_GAVE_UP: BFD session [chars] removal failed due to ACL removal failure interface [chars]Explanation BFD session [chars] removal failed due to ACL removal failure interface [chars.
Recommended Action Maximum acl removal retries exceeded. Please manually remove bfd sessions.
Error Message BFD-3-SESSION_CREATE_FAIL Format: Failed to create BFD session to neighbor %s over intertface %s. Reason %sExplanation Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-3-SESSION_CREATE_FAIL: Failed to create BFD session to neighbor [chars] over intertface [chars]. Reason [chars]Explanation Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars].
Recommended Action SYSLOGDPC_NO_ACTION.
BFD-4
Error Message BFD-4-INVALID_NBR Format: Attempt to BFD session failed for application %s.Explanation Attempt to BFD session failed for application [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-4-INVALID_NBR: Attempt to BFD session failed for application [chars].Explanation Attempt to BFD session failed for application [chars].
Recommended Action No action is required.
Error Message BFD-4-INVALID_NBR: Attempt to register BFD session on invalid neighbor: [chars], by application=[chars]Explanation Attempt to register BFD session on invalid neighbor: [chars] type that is not supported by BFD for application [chars].
Recommended Action No action is required.
Error Message BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session [chars] failed: Reason [chars] ([hex]).Explanation Attempt to delete [dec] BFD session[chars] failed: Reason [chars] ([hex]).
Recommended Action No action is required.
Error Message BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session for neighbor [chars] failed: Reason [chars] ([hex]).Explanation Attempt to delete BFD session for neighbor [chars] failed: Reason [chars] ([hex]).
Recommended Action No action is required.
BFD-5
Error Message BFD-5-BFD_DISABLED: BFD DisabledExplanation BFD Service Disabled.
Recommended Action No action is required.
Error Message BFD-5-BFD_ENABLED: BFD EnabledExplanation BFD Service nabled.
Recommended Action No action is required.
Error Message BFD-5-BFD_SESSION_ADD: BFD session [hex] addedExplanation BFD Service Disabled.
Recommended Action No action is required.
Error Message BFD-5-BFD_SESSION_DOWN: BFD session [hex] downExplanation BFD Service Disabled.
Recommended Action No action is required.
Error Message BFD-5-BFD_SESSION_REM: BFD session [hex] removedExplanation BFD Service Disabled.
Recommended Action No action is required.
Error Message BFD-5-BFD_SESSION_UP: BFD session [hex] upExplanation BFD Service Disabled.
Recommended Action No action is required.
Error Message BFD-5-DISABLED Format: BFD DisabledExplanation BFD Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-ENABLED Format: BFD EnabledExplanation BFD Service enabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_ACTIVE_PARAMS_CHANGE Format: Local parameter of BFD session 0x%x has changed %sExplanation Local parameter of BFD session [hex] has changed [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_ACTIVE_PARAMS_CHANGE: Local parameter of BFD session [hex] has changed [chars]Explanation Local parameter of BFD session [hex] has changed [chars].
Recommended Action No action is required.
Error Message BFD-5-SESSION_CREATED Format: BFD session to neighbor %s on interface %s has been createdExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_CREATED: BFD session to neighbor [chars] on interface [chars] has been createdExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action No action is required.
Error Message BFD-5-SESSION_LOCAL_PARAMS_CHANGE Format: Local parameter of BFD session 0x%x has changed %sExplanation Local parameter of BFD session [hex] has changed [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session [hex] has changed [chars]Explanation Local parameter of BFD session [hex] has changed [chars].
Recommended Action No action is required.
Error Message BFD-5-SESSION_MOVED Format: BFD session 0x%x: %sExplanation BFD session [hex]: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_MOVED: BFD session [hex]: [chars]Explanation BFD session [hex]: [chars].
Recommended Action No action is required.
Error Message BFD-5-SESSION_NO_RESOURCES Format: No resource for session to neighbor %s on interface %sExplanation The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_NO_RESOURCES: No resource for session to neighbor [chars] on interface [chars]Explanation The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].
Recommended Action Remove other BFD sessions to free resources for this session.
Error Message BFD-5-SESSION_REMOVED Format: BFD session to neighbor %s on interface %s has been removedExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_REMOVED: BFD session to neighbor [chars] on interface [chars] has been removedExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action No action is required.
Error Message BFD-5-SESSION_STATE_DOWN Format: BFD session %s to neighbor %s on interface %s has gone down. Reason: 0x%x.Explanation BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex].Explanation BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.
Recommended Action No action is required.
Error Message BFD-5-SESSION_STATE_UP Format: BFD session %s to neighbor %s on interface %s is up.Explanation BFD session [chars] to neighbor [chars] on interface [chars] is up.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-5-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on interface [chars] is up.Explanation BFD session [chars] to neighbor [chars] on interface [chars] is up.
Recommended Action No action is required.
BFD-6
Error Message BFD-6-SESSION_ACL_INSTALL_FAILED Format: BFD session %s failed due to missing ACL resources for interface %sExplanation BFD session [chars] failed due to missing ACL resources for interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-6-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to missing ACL resources for interface [chars]Explanation BFD session [chars] failed due to missing ACL resources for interface [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_ACL_REMOVE_FAILED Format: BFD session %s removal failed due to missing ACL resources for interface %sExplanation BFD session [chars] removal failed due to missing ACL resources for interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFD-6-SESSION_ACL_REMOVE_FAILED: BFD session [chars] removal failed due to missing ACL resources for interface [chars]Explanation BFD session [chars] removal failed due to missing ACL resources for interface [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_CREATED: BFD session to neighbor [chars] on interface [chars] has been createdExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session [chars] has changed: [chars]Explanation Local parameter of BFD session [chars] has changed: [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_MOVED: BFD session [chars] has moved from [chars] to [chars]Explanation BFD session [chars] has moved from [chars] to [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_NO_RESOURCES: No resource for session to neighbor [chars] on interface [chars]Explanation The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].
Recommended Action Remove other BFD sessions to free resources for this session.
Error Message BFD-6-SESSION_NO_RESOURCES_CLR: Lack of resources condition has cleared for session to neighbor [chars] on interface [chars]Explanation Lack of resources condition has cleared for session to neighbor [chard] on interface [char].
Recommended Action No action is required.
Error Message BFD-6-SESSION_REMOVED: BFD session to neighbor [chars] on interface [chars] has been removedExplanation BFD session to neighbor [chars] on interface [chars].
Recommended Action No action is required.
Error Message BFD-6-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex].Explanation BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.
Recommended Action No action is required.
Error Message BFD-6-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on interface [chars] is up.Explanation BFD session [chars] to neighbor [chars] on interface [chars] is up.
Recommended Action No action is required.
BFDC-SLOT# Messages
This section contains the BFDC-SLOT# messages.
BFDC-SLOT#-2
Error Message BFDC-SLOT#-2-BFDC_GENERAL_FAILURE: General failure. [chars]Explanation General failure. This is a critical failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFDC-SLOT#-2-BFDC_MALLOC_FAILED: Memory allocation failed. [chars]Explanation Memory allocation failed. This is a critical failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BFDC-SLOT#-2-BFDC_MTS_FAILURE: MTS failure. [chars]Explanation MTS related failure. This is a critical failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BGP Messages
This section contains the BGP messages.
BGP-1
Error Message BGP-1-FATAL Format: Fatal error: %s: %sExplanation An unexpected fatal error has occurred.
Parameters: Error Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-1-UNKNOWNFATAL Format: Unknown fatal error %d: %sExplanation An unexpected fatal error has occurred.
Parameters: Error Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
BGP-2
Error Message BGP-2-AFINIT Format: Error initializing address family, (%d)Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-AFINITFUNCS Format: Error initializing address family function vectors, (%d)Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-ATTACH Format: Unable to attach to %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-IPV6REG Format: Unable to register with IPv6Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-MQLOOP_INIT Format: Message queue loop %s, %s, Error - %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: MQLoop Type, Failure Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-PEERSHALTED Format: BGP %s shutdown due to no memory condition (%s)Explanation The system may be low on memory.
Parameters: Peer(s), Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-2-PTHREAD Format: procket_pthread_create failed for %s: error %dExplanation An unexpected fatal error has occurred.
Parameters: Thread Name, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SRVREG Format: Unable to register with %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SYSMGR_CONDVERIF Format: Sysmgr conditional verify failedExplanation An internal software error occurred.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An internal software error occurred.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-TSP_INIT Format: Unable to initialize with TSPExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-U6RIBREG Format: Unable to register with U6RIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-URIBREG Format: Unable to register with URIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
BGP-3
Error Message BGP-3-ALLOCFAIL Format: %s malloc (%ld) failed for: %sExplanation The system may be low on memory.
Parameters: Alloc Type, Size, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-APPLY_BESTPATH_CFG Format: Failed to apply bestpath configuration: %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ASLEN Format: AS-PATH prepend length exceeds internal limitExplanation The system has exceeded an internal limit when prepending an AS path.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ASSERT Format: %s:%d: Assertion `%s' failed.Explanation An internal software error occurred.
Parameters: File Name, Line Number, Assert Type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BADPEERAS Format: VRF %s, Peer %s - bad remote-as, expecting %s received %s.Explanation The system has detected an error when prepending to an AS path.
Parameters: Segment Type, Segment Length ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SEND_AUTO_EXPIRY Format: Unable to start BFD staling, error %s(0x%08x)Explanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SEND_EXPIRE_NOW Format: Unable to expire staled BFD sessions, error %s(0x%08x)Explanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SES_ADD Format: Unable to add BFD session for peer %s, error %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SES_CREATE Format: Unable to create BFD session Id for peer %s, error %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SES_REMOVE Format: Unable to remove BFD session for peer %s, error %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BFD_SES_REMOVE_ALL Format: Unable to cleanup the BFD sessions during deconfiguration, error %s(0x%08x)Explanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-COMADD Format: Error occurred in community addition, no action takenExplanation An internal error was encountered in adding a community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-COMLEN Format: Community sets exceeded maximum allowed limitExplanation An internal limit was hit in adding a community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-CONDSRV_CLEANUP Format: Conditional Service cleanup request failed, %sExplanation Sysmgr rejected BGP's request to shut down.
Recommended Action No action is required.
Error Message BGP-3-EBGPTTL Format: Unable to set EBGP TTL for peer %s, fd %dExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-EVENT_WAIT Format: Error while waiting for %s event, error - %s\nExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-EXTCOMADD Format: Error occurred in extended community addition, no action takenExplanation An internal error was encountered in adding an extended community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-EXTCOMLEN Format: Extended community sets exceeded maximum allowed limitExplanation An internal limit was hit in adding an extended community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ILLARGS Format: %s called with illegal argumentsExplanation An internal software error occurred.
Parameters: Function ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-INTERNAL Format: Internal error %d: %sExplanation An internal software error occurred.
Parameters: Error Type, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-INVHDR Format: Peer %s sent unexpected header patternExplanation The marker pattern in the message header was invalid.
Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-3-IPTOS Format: Unable to set IP TOS bits for %s, fd %dExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-LISTEN_SOCK Format: Failed to listen on %s BGP TCP portExplanation BGP_EXPL_SOCK_ERROR
Parameters: Address-family ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-LOWMEM Format: Low on heap memoryExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MD5PASS Format: Cannot set MD5 password %s for peer %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MQLOOP_SHUTDOWN Format: Couldn't shut down %s message queue loopExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NBRERR Format: %s Peer error: %sExplanation An internal software error occurred.
Parameters: Peer address, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NEGWRITE Format: Negative nr of %d bytes left to write to peer %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NOBUF Format: [%s] Unable to get buffer for %s msg to peer %sExplanation An internal software error occurred.
Parameters: Address-family, Msg Type, Peer address ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NOMEMORY Format: Could not allocate %sExplanation The system may be low on memory.
Parameters: Data Type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PATH_DEL Format: Failed to destroy path (%s), error %dExplanation The BGP process may have run out of memory.
Parameters: Path Type, Error ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-PATH_STALE Format: [%s] %s path being %s, for %s/%d from peer %s, should not be staleExplanation An internal software error occurred.
Parameters: Address-family, Path State, Operation, Prefix/masklength, Peer address ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PFX_NOMEM Format: Could not allocate %s for %s/%dExplanation The system may be low on memory.
Parameters: Data Type, Prefix/masklength ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-RESTARTINIT Format: Unable to determine restart status and initializeExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-RESTARTTYPE Format: Error in learning restart typeExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-RNHCB Format: RNH %s error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SENDBUF Format: Error manipulating sendbuf: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SNMP_API_DATA Format: Message data is NULLExplanation An SNMP message does not have enough memory to store data.
Recommended Action No action is required.
Error Message BGP-3-SOCK_ACCEPT Format: Socket (%d/%d) accept: %s\nExplanation BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCK_ERR Format: Socket (%d/%d): %s\nExplanation BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCK_FDPOP Format: Unexpected error during socket fd population %s(%d)Explanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCK_RECV Format: Unexpected error during socket data recv %s(%d)Explanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKBIND Format: Cannot bind local socket for peer %s: %sExplanation An error occurred during a socket operation.
Parameters: Peer address, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKCREATE Format: Cannot create socket for peer %s: %s, stats: %lu/%lu/%lu/%lu/%luExplanation An error occurred during a socket operation.
Parameters: Peer address, Error, Socket stats ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKNONBLOCK Format: Couldn't make fd %d non-blocking: %sExplanation An error occurred during a socket operation.
Parameters: Socket fd, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKOPEN Format: TCP connection for peer %s already open, fd %d, state %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOFTINCAP Format: Peer %s not capable of soft refresh in, operator intervention needed: %sExplanation The router is unable to do a soft refresh for the indicated peer.
Recommended Action If necessary, reset the connection with the peer.
Error Message BGP-3-SRAND Format: Failed to set random seedExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-THREAD_SHUTDOWN Format: Problem shutting down thread %s: Operation - %s, Error - %s\nExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-TIMER_START Format: Couldn't start %s timer %sExplanation An internal software error occurred.
Parameters: Timer Type, Data ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-U6RIBRNH Format: U6RIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ULIBREG Format: Unable to register with ULIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-ULIBRNH Format: ULIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-UNEXPECT Format: %s L%d: %sExplanation An internal software error occurred.
Parameters: File Name, Line Number, Unexpected condition ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-URIBRNH Format: URIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-URIBRT Format: URIB RT error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BGP-4
Error Message BGP-4-ISSU_CHECK Format: Not ready for ISSU: Graceful Restart or hold time check failedExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-ISSU_HOLDTIME Format: ISSU will be affected if hold time is less than or equal to system switchover time (%d seconds)\nExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-NODAMPMEM Format: [%s] Unable to dampen prefix %s/%d from peer %s due to no memoryExplanation BGP_EXPL_NO_MEMORY
Parameters: Address-family, Prefix/masklength, Peer address ...Recommended Action No action is required.
Error Message BGP-4-NORID Format: Peer %s sent us 0.0.0.0 as its router-idExplanation A BGP peer sent us an invalid router ID.
Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-4-SAMERID Format: Peer %s uses same routerid as usExplanation A BGP peer is using the same router ID as this router.
Recommended Action Configure either the local or remote router with a different router ID.
Error Message BGP-4-SNMP_REGFAIL Format: Failed to register MIB with the SNMP agent, the BGP MIB will be unavailable. (%s)\nExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BGP-5
Error Message BGP-5-BADSIG Format: Should not have received signal %dExplanation An unexpected but handleable event has occurred.
Recommended Action No action is required.
BIOS_DAEMON Messages
This section contains the BIOS_DAEMON messages.
BIOS_DAEMON-2
Error Message BIOS_DAEMON-2-BIOS_DAEMON_FLASH_WARNING: Flash chip not supported by running image. Skipping bios upgrade.Explanation BIOS CHIP NOT SUPPORTED.
Recommended Action No action is required.
Error Message BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: Primary BIOS is corrupted or un-bootableExplanation The system detects that the primary BIOS has been corrupted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: System booted from Alternate BIOS FlashExplanation Boot from Alternate.
Recommended Action SYSLOGDOC_NOACTION.
Error Message BIOS_DAEMON-2-BIOS_DAEMON_SUP_ERROR: BIOS Sector ([dec]) is write protectedExplanation The system detects that the BIOS write has been protected.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-2-FLASH_WARNING Format: Flash chip not supported by running image. Skipping bios upgrade.Explanation BIOS CHIP NOT SUPPORTED.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-2-PRI_BOOT_FAIL Format: System booted from Alternate BIOS FlashExplanation Boot from Alternate.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BIOS_DAEMON-5
Error Message BIOS_DAEMON-5-BIOS_DAEMON_PRI_BOOT: System booted from Primary BIOS FlashExplanation Boot from Primary.
Recommended Action SYSLOGDOC_NOACTION.
Error Message BIOS_DAEMON-5-PRI_BOOT Format: System booted from Primary BIOS FlashExplanation Boot from Primary.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BIOS_DAEMON-SLOT# Messages
This section contains the BIOS_DAEMON-SLOT# messages.
BIOS_DAEMON-SLOT#-2
Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is write protectedExplanation The system detects that the BIOS write has been protected.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: Primary BIOS is corrupted or un-bootableExplanation The system detects that the primary BIOS has been corrupted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: System booted from Alternate BIOS FlashExplanation Boot from Alternate.
Recommended Action SYSLOGDOC_NOACTION.
BIOS_DAEMON-SLOT#-5
Error Message BIOS_DAEMON-SLOT#-5-BIOS_DAEMON_LC_PRI_BOOT: System booted from Primary BIOS FlashExplanation Boot from Primary.
Recommended Action SYSLOGDOC_NOACTION.
BOOTUP_TEST Messages
This section contains the BOOTUP_TEST messages.
BOOTUP_TEST-2
Error Message BOOTUP_TEST-2-EOBC_FAIL Format: Module %d has failed test %s on EOBC due to error %sExplanation The online diagnostic EOBC test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTUP_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC due to error [chars]Explanation The online diagnostic EOBC test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-EOBC_SKIP Format: Module %d has failed test %s on EOBC due to error %sExplanation The online diagnostic ManagementPort test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTUP_TEST-2-EOBC_SKIP: Module [dec] has failed test [chars] on EOBC due to error [chars]Explanation The online diagnostic ManagementPort test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-MGMT_PORT_FAIL Format: Module %d has failed test %s on Management Port due to error %sExplanation The online diagnostic ManagementPort test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTUP_TEST-2-MGMT_PORT_FAIL: Module [dec] has failed test [chars] on Management Port due to error [chars]Explanation The online diagnostic ManagementPort test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-MGMT_PORT_SKIP Format: Module %d has skipped test %s on Management Port due to error %sExplanation The online diagnostic ManagementPort test is skipped.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTUP_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] on Management Port due to error [chars]Explanation The online diagnostic ManagementPort test is skipped.
Recommended Action No action is required.
BOOTVAR Messages
This section contains the BOOTVAR messages.
BOOTVAR-2
Error Message BOOTVAR-2-ALLOC_MEMORY Format: Memory allocation failedExplanation The service failed to allocate memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-2-ALLOC_MEMORY: Memory allocation failedExplanation The service failed to allocate memory.
Recommended Action Check if the system is low on memory, if so, reset the switch.
Error Message BOOTVAR-2-AUTOCOPY_FAILED: Autocopy of file [chars] to standby failed. [chars] (Error-id: [hex])Explanation The image to be copied to standby vi the auto-copy feature failed.
Recommended Action Check error id for specified reason.
Error Message BOOTVAR-2-AUTOSYNC_FAILED: Image autosync failed. Reason: [chars] ([hex])Explanation Image synchronization failed.
Recommended Action Check that there is enough space on the flash, and check the system high availability status.
Error Message BOOTVAR-2-CONFIG_ERROR Format: Failed to update boot configurationExplanation An error has occurred during the update of the boot configuration files.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-2-CONFIG_ERROR: Failed to update boot configurationExplanation An error has occurred during the update of the boot configuration files.
Recommended Action Check that there is enough space on the flash, enter the show boot command to check the configured image names, enter the show loader internal command to compare the configurations, if the configurations do not match, enter the write erase command and retry saving the configuration.
Error Message BOOTVAR-2-IMAGE_NOT_COMPATIBLE Format: Warning: image %s is not compatible with the current platform in SUP %dExplanation The input image name is not compatible with the current platform.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-2-IMAGE_NOT_COMPATIBLE: Warning: image [chars] is not compatible with the current platform in SUP [dec]Explanation The input image name is not compatible with the current platform.
Recommended Action Make sure that the system has the correct image before you reboot.
BOOTVAR-3
Error Message BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL Format: Autocopy of file %s to standby failed due to not enough disk space on standbyExplanation There is not enough disk space on the standby for the file to be copied.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL: Autocopy of file [chars] to standby failed due to not enough disk space on standbyExplanation There is not enough disk space on the standby for the file to be copied.
Recommended Action Clear space on the standby disk.
Error Message BOOTVAR-3-INIT_FAILED Format: Initialization failed: Component %sExplanation The system detects that the service has failed to start. The failure occurs during initialization of the component [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-INIT_FAILED: Initialization failed: Component [chars]Explanation The system detects that the service has failed to start. The failure occurs during initialization of the component [chars].
Recommended Action Enter the show processes command to check the status of the other processes, pay attention to the specified component.
Error Message BOOTVAR-3-LOAD_VERIFY_LIB_FAILED Format: Fetching library %s failedExplanation The system has failed to load bootvar that is specified in the verification library.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-LOAD_VERIFY_LIB_FAILED: Fetching library [chars] failed, reason=[chars]Explanation The system has failed to load bootvar that is specified in the verification library.
Recommended Action No action is required.
Error Message BOOTVAR-3-MODULE_LOCK_FAIL Format: Unable to get module lockExplanation unable to acquire modlock to prevent the user to reload duringautosynchronization.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-MODULE_LOCK_FAIL: Unable to get module lock, please don't reload <error-id:[hex]>Explanation The system is unable to acquire modlock to prevent the user to reload duringautosynchronization.
Recommended Action No action is required.
Error Message BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY Format: auto-copy failed - not supported by neighbor supervisor.Explanation The autocopy has failed because it is not supported by the standby supervisor module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY: auto-copy failed - not supported by neighbor supervisor.Explanation The autocopy has failed because it is not supported by the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-3-VERIFY_FAILED Format: Image %s for bootvar %s verification failedExplanation The image set for this bootvar has failed the verification process.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-3-VERIFY_FAILED: Image [chars] for bootvar [chars] verification failed, reason=[chars]Explanation The image set for this bootvar has failed the verification process.
Recommended Action Check reason to determine actions.
BOOTVAR-5
Error Message BOOTVAR-5-AUTOCOPY_SUCCEED Format: auto-copy of file %s to standby supervisor succeedExplanation auto copy of the file succeed, image integrity verified by standby.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-AUTOCOPY_SUCCEED: auto-copy of file [chars] to standby supervisor succeedExplanation The autocopy of the file has succeeded. The image integrity has been verified by the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED Format: Unable to ask standby to verify file %sExplanation When the image was copied to the standby supervisor module, the system failed to ask the standby supervisor module to verify the integrity of the image.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED: Unable to ask standby to verify file [chars], error = [hex]Explanation When the image was copied to the standby supervisor module, the system failed to ask the standby supervisor module to verify the integrity of the image.
Recommended Action Turn auto-copy off and back on.
Error Message BOOTVAR-5-AUTOSYNC_DONE Format: Image autosync doneExplanation The image synchronization was successful.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-AUTOSYNC_DONE: Image autosync doneExplanation The image synchronization was successful.
Recommended Action No action is required.
Error Message BOOTVAR-5-AUTOSYNC_REBOOT Format: Rebooting standby after successful autosyncExplanation The image autosynchronization has been successful. The system is resetting the standby supervisor to load the new image.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-AUTOSYNC_REBOOT: Rebooting standby after successful autosyncExplanation The image autosynchronization has been successful. The system is resetting the standby supervisor to load the new image.
Recommended Action Check that the standby supervisor module reloads correctly.
Error Message BOOTVAR-5-AUTOSYNC_START Format: Starting image autosync. Please wait until completion...Explanation The standby supervisor module has requested the synchronizationof the current image.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-AUTOSYNC_START: Starting image autosync. Please wait until completion...Explanation The standby supervisor module has requested the synchronizationof the current image.
Recommended Action No action is required.
Error Message BOOTVAR-5-IMAGE_NOTEXISTS Format: Warning: image %s doesn't exist on sup%dExplanation The input image name does not exist on the specified supervisor.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-IMAGE_NOTEXISTS: Warning: image [chars] doesn't exist on sup[dec]Explanation The input image name does not exist on the specified supervisor.
Recommended Action Check whether the input image name you entered exists and make sure that you have the image on the flash before you reboot.
Error Message BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY Format: auto-copy supported by neighbor supervisorExplanation The information log reports that the standby supervisor module supports autocopy. Autocopy is being started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting...Explanation The information log reports that the standby supervisor module supports autocopy. Autocopy is being started.
Recommended Action No action is required.
BOOTVAR-6
Error Message BOOTVAR-6-ALREADY_IN_SYNC Format: Image already in syncExplanation This message indicates that you do not need to update the image on the standby supervisor module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-6-ALREADY_IN_SYNC: Image already in syncExplanation This message indicates that you do not need to update the image on the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-6-AUTOCOPY_DID_NOT_START: Autocopy of file [chars] to standby did not start. [chars] (Error-id: [hex])Explanation Autocopy of the file did not start as the remote copy location does not exist.
Recommended Action No action is required.
Error Message BOOTVAR-6-CONFIG_UPDATED Format: Boot configuration updatedExplanation The boot-loader configuration files have been successfully updated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-6-CONFIG_UPDATED: Boot configuration updatedExplanation The boot-loader configuration files have been successfully updated.
Recommended Action No action is required.
Error Message BOOTVAR-6-STARTING Format: Boot configuration initializedExplanation The service has successfully started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BOOTVAR-6-STARTING: Boot configuration initializedExplanation The service has successfully started.
Recommended Action No action is required.
CALLHOME Messages
This section contains the CALLHOME messages.
CALLHOME-2
Error Message CALLHOME-2-EVENT Format: %sExplanation A Call Home event [chars] occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-2-EVENT: [chars]Explanation A Call Home event [chars] occurred.
Recommended Action If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.
Error Message CALLHOME-2-PROGRAM_EXIT Format: callhome process ending: %s\nExplanation A Call Home process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-2-PROGRAM_EXIT: callhome process ending: [chars]Explanation A Call Home process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CALLHOME-3
Error Message CALLHOME-3-CALLHOME_CFS_MERGE_OPERATION_FAILED: [chars]Explanation [chars1].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CALLHOME-3-CALLHOME_CFS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CALLHOME-3-CALLHOME_MAX_ALERT_MSG: [chars]Explanation [chars].
Recommended Action Check the reason for the generation of the Call Home messages and fix the problem.
Error Message CALLHOME-3-CFS_MERGE_OPERATION_FAILED Format: %sExplanation [chars1].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-3-CFS_OPERATION_FAILED Format: %s : %sExplanation [chars1] [chars2].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-3-EVENT_PROCESS_ERROR Format: error in processing callhome event %s reason:%sExplanation An error has occurred when processing the Call Home event [chars] reason:[chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-3-EVENT_PROCESS_ERROR: error in processing callhome event [chars] reason:[chars]Explanation An error has occurred when processing the Call Home event [chars] reason:[chars].
Recommended Action Check that Call Home is properly configured on your system. Check the SMTP server address, e-mail addresses for destination profiles and enable Call Home. Use show Call Home commands for displaying the configuration.
Error Message CALLHOME-3-MAX_ALERT_MSG Format: %sExplanation [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-3-MESSAGE_SIZE_EXCEED Format: message size for callhome alert:%s exceeds maximum limit for destination profile:%sExplanation The message size for Call Home alert:[chars] exceeds the maximum limit for destination profile:[chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-3-MESSAGE_SIZE_EXCEED: message size for callhome alert:[chars] exceeds maximum limit for destination profile:[chars]Explanation The message size for Call Home alert:[chars] exceeds the maximum limit for destination profile:[chars].
Recommended Action Check the maximum message size for the destination profile . Increase it if possible to match the maximum limit allowed by your e-mail destinations.
CALLHOME-6
Error Message CALLHOME-6-NONCRIT_EVENT Format: %sExplanation A noncritical Call Home event [chars] occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CALLHOME-6-NONCRIT_EVENT: [chars]Explanation A noncritical Call Home event [chars] occurred.
Recommended Action If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.
CDP Messages
This section contains the CDP messages.
CDP-2
Error Message CDP-2-INITFAIL: CDP Daemon Initialization failed: [chars]Explanation CDP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
CDP-3
Error Message CDP-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation The CDP daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CDP-3-GENERROR: [chars]Explanation The CDP daemon encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action No action is required.
Error Message CDP-3-MCASTBINDFAIL: Failed to bind for CDP multicast address on interface [hex] - [chars]Explanation An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-MTSERROR: [chars]Explanation The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message CDP-3-PKTRECVFAIL: Failed to receive packet - [chars]Explanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-PKTSENDFAIL: Failed to send packet, interface [hex] - [chars]Explanation The system has failed to send the packet. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-PSSERROR: [chars]Explanation The CDP daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CDP-3-SOCKBINDFAIL: Failed to bind to raw socket, interface [hex] - [chars]Explanation The system has failed to bind to a raw socket. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-SOCKOPENFAIL: Failed to open socket for receiving raw 802_2 packets - [chars]Explanation An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.
Recommended Action No action is required.
CDP-4
Error Message CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on [chars], with [chars]Explanation A duplex mismatch has been discovered from the received CDP packet.
Recommended Action No action is required.
Error Message CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on [chars]([dec]), with [chars]([dec])Explanation A native VLAN mismatch has been discovered.
Recommended Action No action is required.
CDP-5
Error Message CDP-5-DISABLED: CDP is disabledExplanation CDP is disabled on the device.
Recommended Action No action is required.
Error Message CDP-5-ENABLED: CDP is enabledExplanation CDP is enabled on the device.
Recommended Action No action is required.
CDP-6
Error Message CDP-6-CDPDUP: CDP Daemon Up.Explanation The CDP daemon was created successfully and is up and running.
Recommended Action No action is required.
Error Message CDP-6-CDPEXIT: CDP Daemon shutting down gracefully.Explanation The CDP daemon is shutting down gracefully.
Recommended Action No action is required.
Error Message CDP-6-NEIGHBOR_ADDED: Device [chars] discovered of type [chars] with port [chars] on incoming port [chars] with ip addr [chars] and mgmt ip [chars]Explanation The system discovered a neighbor device.
Recommended Action No action is required.
Error Message CDP-6-NEIGHBOR_REMOVED: CDP Neighbor [chars] on port [chars] has been removedExplanation The system deleted a neighbor device.
Recommended Action No action is required.
Error Message CDP-6-PORTDISABLE: CDP disabled on port [chars]Explanation CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTDOWN: A CDP enabled port [chars] went down.Explanation A CDP enabled port became unoperational. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTENABLE: CDP enabled on port [chars]Explanation CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTUP: A CDP enabled port [chars] came up.Explanation A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
CDPD Messages
This section contains the CDPD messages.
CDPD-2
Error Message CDPD-2-INITFAIL Format: CDP Daemon Initialization failed: %sExplanation CDP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CDPD-3
Error Message CDPD-3-ALLOCFAIL Format: Heap Memory allocation failed: %sExplanation The CDP daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-GENERROR Format: %sExplanation The CDP daemon encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-MCASTBINDFAIL Format: Failed to bind for CDP multicast address on interface 0x%x - %sExplanation An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface and [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-MTSERROR Format: %sExplanation The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-PKTRECVFAIL Format: Failed to receive packet - %sExplanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-PKTSENDFAIL Format: Failed to send packetExplanation The system has failed to send the packet. [dec] identifies the interface and [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-PSSERROR Format: %sExplanation The CDP daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-SOCKBINDFAIL Format: Failed to bind to raw socketExplanation The system has failed to bind to a raw socket. [dec] identifies the interface and [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-3-SOCKOPENFAIL Format: Failed to open socket for receiving raw 802_2 packets - %sExplanation An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CDPD-4
Error Message CDPD-4-DUPLEX_MISMATCH Format: Duplex mismatch discovered on %sExplanation duplex mismatch discovered from the received CDP packet.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CDPD-5
Error Message CDPD-5-DISABLED Format: CDP is disabledExplanation CDP is disabled on the device.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-5-ENABLED Format: CDP is enabledExplanation CDP is enabled on the device.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CDPD-6
Error Message CDPD-6-CDPDUP Format: CDP Daemon Up.Explanation The CDP daemon was created successfully and is up and running.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-CDPEXIT Format: CDP Daemon shutting down gracefully.Explanation The CDP daemon is shutting down gracefully.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-NEIGHBOR_ADDED Format: Device %s discovered of type %s with port %s on incoming port %s with ip addr %s and mgmt ip %sExplanation The system discovered a neighbor device.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-NEIGHBOR_REMOVED Format: CDP Neighbor %s on port %s has been removedExplanation The system deleted a neighbor device.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-PORTDISABLE Format: CDP disabled on port %sExplanation CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-PORTDOWN Format: A CDP enabled port %s went down.Explanation A CDP enabled port became unoperational. [chars] is the interface-ID string that identifies the port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-PORTENABLE Format: CDP enabled on port %sExplanation CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CDPD-6-PORTUP Format: A CDP enabled port %s came up.Explanation A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_EN Messages
This section contains the CERT_EN messages.
CERT_EN-2
Error Message CERT_EN-2-PROGRAM_EXIT Format: cert_enroll daemon exiting: %s\nExplanation cert_enroll daemon is exiting.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_EN-3
Error Message CERT_EN-3-ERROR_MESSAGE Format: %sExplanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CERT_EN-3-FIPS_MODE_INIT_ERROR Format: Could not initialize FIPS mode : %sExplanation This message indicates that a FIPS mode error has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_EN-6
Error Message CERT_EN-6-MESSAGE Format: %sExplanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_ENROLL Messages
This section contains the CERT_ENROLL messages.
CERT_ENROLL-2
Error Message CERT_ENROLL-2-CERT_EN_PROGRAM_EXIT: cert_enroll daemon exiting: [chars]Explanation The CERT_ENROLL daemon is exiting.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_ENROLL-3
Error Message CERT_ENROLL-3-CERT_EN_ERROR_MESSAGE: [chars]Explanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action No action is required.
Error Message CERT_ENROLL-3-CERT_EN_FIPS_MODE_INIT_ERROR: Could not initialize FIPS mode : [chars]Explanation This message indicates that a FIPS mode error has occurred.
Recommended Action No action is required.
CERT_ENROLL-6
Error Message CERT_ENROLL-6-CERT_EN_MESSAGE: [chars]Explanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action No action is required.
CFS Messages
This section contains the CFS messages.
CFS-2
Error Message CFS-2-CFS_REJECT: CFS reject: [chars]: Switch WWN [chars], ip [chars], reason [chars]Explanation This message indicates that the CFS process was rejected: [chars] Switch WWN [chars], ip [chars], reason [chars].
Recommended Action No action is required.
Error Message CFS-2-EXITING: Exit reason: [chars]Explanation The CFS service process has exited due to [char]. The process has probably been restarted automatically.
Recommended Action No action is required.
Error Message CFS-2-GENERAL_ERROR: [chars]Explanation The CFS service has encountered a critical error. The description of the error is [str.].
Recommended Action No action is required.
Error Message CFS-2-INITFAIL Format: CFS Service Init failed: %sExplanation CFS Service initialization failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-INITFAIL: CFS Service Init failed: [chars]Explanation CFS Service initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message CFS-2-LOCK_FAILED Format: lock failed for sap %d due to internal error.Explanation Lock failed due to Unrestricted uncoordinated count is out of synchronizationfor sap [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-LOCK_FAILED: lock failed for sap [dec] due to internal error.Explanation Lock failed due to Unrestricted uncoordinated count is out of synchronizationfor sap [dec].
Recommended Action To recover from this state run command 'cfs internal decrement-unrestricted <app-sap>'.
Error Message CFS-2-MALLOC_ERROR Format: Size %d bytesExplanation The CFS service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-MALLOC_ERROR: Size [dec] bytesExplanation The CFS service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-MTS_REJECT Format: Verification failed reject MTS message SAP %d:RR-token 0x%xExplanation This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then therefore ignore the MTS message, Source SAP [dec]; RR-token [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-MTS_REJECT: Verification failed reject MTS message SAP [dec]:RR-token [hex]Explanation This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then therefore ignore the MTS message, Source SAP [dec]; RR-token [hex].
Recommended Action No action is required.
Error Message CFS-2-PSS_ERROR Format: %s: PSS ret. val=%dExplanation The CFS service encountered an error while operating on a persistent storage database.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-PSS_ERROR: [chars]: PSS ret. val=[dec]Explanation The CFS service encountered an error while operating on a persistent storage database.
Recommended Action No action is required.
Error Message CFS-2-REJECT Format: CFS reject: %s: Switch WWN %sExplanation This message indicates that the CFS process was rejected: [chars] Switch WWN [chars], ip [chars], reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-VDC_MGR_FAIL Format: Failed to get a valid switch mac from VDC Manager: %sExplanation VDC manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-VDC_MGR_FAIL: Failed to get a valid switch mac from VDC Manager: [chars]Explanation VDC manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received.
Recommended Action No action is required.
CFS-3
Error Message CFS-3-ALLOCFAIL Format: Heap Memory allocation failed: %sExplanation CFS Service is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation CFS Service is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-APP_MERGE_FAILED: Merge failed for app [chars], local switch wwn [chars], remote switch wwn [chars].Please check 'show cfs merge status name [chars]' for more informationExplanation The CFS service has detected a merge failure.
Recommended Action No action is required.
Error Message CFS-3-CFS_PSS_CORRUPTED: [chars] PSS found corruptedExplanation The CFS service has detected a corrupted file in its persistent information databases The database would be recreated.
Recommended Action No action is required.
Error Message CFS-3-DBERROR Format: %sExplanation CFS Service encountered a database error. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-DBERROR: [chars]Explanation CFS Service encountered a database error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-FAILURE_RESPONSE Format: %s 0x%xExplanation CFS Service failed to get response [chars][hex] specify the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-FAILURE_RESPONSE: [chars] [hex]Explanation CFS Service failed to get response [chars][hex] specify the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-FIPS_TEST_FAILED Format: FIPS compliance test failedExplanation FIPS compliance test failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-FIPS_TEST_FAILED: FIPS compliance test failedExplanation FIPS compliance test failed.
Recommended Action No action is required.
Error Message CFS-3-GENERROR Format: %sExplanation CFS Service encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-GENERROR: [chars]Explanation CFS Service encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action No action is required.
Error Message CFS-3-LICERR Format: %sExplanation CFS Service failed to get license.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-LICERR: [chars]Explanation CFS Service failed to get license.
Recommended Action No action is required.
Error Message CFS-3-MERGE_FAILED: Merge failed for app [chars], local switch wwn [chars],ip [chars], remote switch wwn [chars], ip [chars]Explanation The CFS service has detected a merge failure.
Recommended Action No action is required.
Error Message CFS-3-MTSERROR Format: %sExplanation CFS Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-MTSERROR: [chars]Explanation CFS Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message CFS-3-PSSERROR Format: %sExplanation CFS Service encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-PSSERROR: [chars]Explanation CFS Service encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-TIMEOUT_ERROR Format: %s 0x%xExplanation CFS Service encountered a timeout [chars][hex] specify the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-TIMEOUT_ERROR: [chars] [hex]Explanation CFS Service encountered a timeout [chars][hex] specify the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-UNKNOWN_MSG Format: Recvd. from Node=%d SAP=%dExplanation The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-3-UNKNOWN_MSG: Recvd. from Node=[dec] SAP=[dec]Explanation The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.
Recommended Action No action is required.
CFS-4
Error Message CFS-4-LICEXP Format: %sExplanation CFS Service license is going to expire. [chars] gives the expected time of expiry.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-4-LICEXP: [chars]Explanation CFS Service license is going to expire. [chars] gives the expected time of expiry.
Recommended Action No action is required.
Error Message CFS-4-PSS_VERSION_MISMATCH Format: PSS %d Code %dExplanation There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]Explanation There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action No action is required.
CFS-6
Error Message CFS-6-BECAME_ACTIVE Format: Became ACTIVE from standby modeExplanation The CFS service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-BECAME_ACTIVE: Became ACTIVE from standby modeExplanation The CFS service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action No action is required.
Error Message CFS-6-BECAME_STDBY Format: Became STANDBY from active modeExplanation The CFS service became standby from active mode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-BECAME_STDBY: Became STANDBY from active modeExplanation The CFS service became standby from active mode.
Recommended Action No action is required.
Error Message CFS-6-EXCESSIVE_DELAY: [chars]Explanation Excessive time taken for a processing event. The description of the event is [str.].
Recommended Action No action is required.
Error Message CFS-6-FAILED_TO_SEND_HEARTBEAT Format: Failed to send heartbeat to system manager: Reason=%sExplanation The CFS service was unable to send heartbeats to the system manager.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]Explanation The CFS service was unable to send heartbeats to the system manager.
Recommended Action No action is required.
Error Message CFS-6-GENERAL_EVENT: [chars]Explanation The CFS service has generated an important event. The description of the event is [str.].
Recommended Action No action is required.
Error Message CFS-6-INVALID_CHECKSUM: Received packet from peer on if-index([hex]) with corrupted checksumExplanation This could be because of the errors in the link.
Recommended Action No action is required.
Error Message CFS-6-INVALID_IF_INDEX: Received packet on if-index([hex]) which is not recognized by CFSExplanation The if-index does not match with the if-index used in discovery orthe systemmight have already received an adjacency cleanup message for this if-index. Check if the if-index is that of the port channel or a physical if-index.
Recommended Action No action is required.
Error Message CFS-6-LOGICAL_DISTRIBUTION_INFO Format: vsan %dExplanation VSAN [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-LOGICAL_DISTRIBUTION_INFO: vsan [dec], source wwn [chars], ip [chars] app-id [dec], session-id [dec], user [chars], [chars]Explanation VSAN [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars].
Recommended Action No action is required.
Error Message CFS-6-PHY_DISTRIBUTION_INFO Format: source wwn %sExplanation source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-PHY_DISTRIBUTION_INFO: source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], [chars]Explanation Source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars].
Recommended Action No action is required.
Error Message CFS-6-PSS_CREATED: [chars] PSS CreatedExplanation One of the persistent information database of CFS service has been recreated.
Recommended Action No action is required.
Error Message CFS-6-PSS_DESTROYED: [chars] PSS DestroyedExplanation One of the persistent information databases of CFS Service has been intentionally destroyed and would be recreated.
Recommended Action No action is required.
Error Message CFS-6-REGION_CTX_REMOVED Format: Region info is deleted for %sExplanation [chars] is in logical scope. Regions support only physical scope applications.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-REGION_CTX_REMOVED: Region info is deleted for [chars]Explanation [chars] is in logical scope. Regions support only physical scope applications.
Recommended Action No action is required.
Error Message CFS-6-SERVICE_UP: Initialized [chars]Explanation The CFS service is up and ready to accept client requests The service was initialized in [char] mode.
Recommended Action No action is required.
Error Message CFS-6-SRVCREATED Format: CFS Service createdExplanation CFS Service was created successfully and is up and running.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-SRVCREATED: CFS Service createdExplanation CFS Service was created successfully and is up and running.
Recommended Action No action is required.
Error Message CFS-6-SRVEXIT Format: CFS Service shutting down gracefullyExplanation CFS Service is shutting down gracefully.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-SRVEXIT: CFS Service shutting down gracefullyExplanation CFS Service is shutting down gracefully.
Recommended Action No action is required.
Error Message CFS-6-SWITCHOVER Format: Switching Over to other Sup.Explanation The CFS service has successfully switched over to the standby supervisor module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-6-SWITCHOVER: Switching Over to other Sup.Explanation The CFS service has successfully switched over to the standby supervisor module.
Recommended Action No action is required.
CIM Messages
This section contains the CIM messages.
CIM-2
Error Message CIM-2-SYSLOG_EXIT Format: Message:%s errcode:%dExplanation exit due to critical error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-2-SYSLOG_PSS_SNAPSHOT_ERR Format: Source URI:%s Destination URI:%s errcode:%dExplanation PSS snapshot error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-2-SYSLOG_SDWRAP_ERR Format: Description:%s errcode:%dExplanation Debug infrastructure error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CIM-3
Error Message CIM-3-SYSLOG_COPY_CONFIG_ERR Format: Message:%s URI:%s errcode:%dExplanation copy running startup error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-3-SYSLOG_FILE_ERR Format: Purpose:%s Filename:%s errcode:%dExplanation File handling error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-3-SYSLOG_MTS_ERR Format: message %sExplanation MTS message handling error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-3-SYSLOG_PSS_ERR Format: Purpose:%s URI:%s errcode:%dExplanation PSS handling error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CIM-6
Error Message CIM-6-LOG_CIM_CERTIFICATE_CLEARED Format: Cleared certificate %sExplanation Cleared a certificate named [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CIM-6-LOG_CIM_CERTIFICATE_INSTALLED Format: Installed certificate %sExplanation Installed a certificate named [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CIMSRVPROV Messages
This section contains the CIMSRVPROV messages.
CIMSRVPROV-2
Error Message CIMSRVPROV-2-CIM_SYSLOG_EXIT: Message:[chars] errcode:[dec]Explanation Exit due to critical error.
Recommended Action No action is required.
Error Message CIMSRVPROV-2-CIM_SYSLOG_PSS_SNAPSHOT_ERR: Source URI:[chars] Destination URI:[chars] errcode:[dec]Explanation PSS snapshot error.
Recommended Action No action is required.
Error Message CIMSRVPROV-2-CIM_SYSLOG_SDWRAP_ERR: Description:[chars] errcode:[dec]Explanation Debug infrastructure error.
Recommended Action No action is required.
CIMSRVPROV-3
Error Message CIMSRVPROV-3-CIM_SYSLOG_COPY_CONFIG_ERR: Message:[chars] URI:[chars] errcode:[dec]Explanation Copy running startup error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_FILE_ERR: Purpose:[chars] Filename:[chars] errcode:[dec]Explanation File handling error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_MTS_ERR: message [chars]Explanation MTS message handling error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_PSS_ERR: Purpose:[chars] URI:[chars] errcode:[dec]Explanation PSS handling error.
Recommended Action No action is required.
CIMSRVPROV-6
Error Message CIMSRVPROV-6-LOG_CIM_CERTIFICATE_CLEARED: Cleared certificate [chars]Explanation Cleared a certificate named [chars].
Recommended Action No action is required.
Error Message CIMSRVPROV-6-LOG_CIM_CERTIFICATE_INSTALLED: Installed certificate [chars]Explanation Installed a certificate named [chars].
Recommended Action No action is required.
CLIS Messages
This section contains the CLIS messages.
CLIS-5
Error Message CLIS-5-CLIS_SYSLOG_CMD_REMOVED: Command deleted from the NVDB: [chars]Explanation Command removal due to configuration change.
Recommended Action No action is required.
Error Message CLIS-5-SYSLOG_CMD_REMOVED Format: Command deleted from the NVDB: %sExplanation Command removal due to configuration change.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLK_MGR Messages
This section contains the CLK_MGR messages.
CLK_MGR-5
Error Message CLK_MGR-5-CLI_CONFIG Format: CLK_MGR clock is synchronized by %s from VDC %dExplanation CLK_MGR clock is synchronized by [chars] from VDC.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLOUD Messages
This section contains the CLOUD messages.
CLOUD-2
Error Message CLOUD-2-PROGRAM_EXIT Format: cloud-discovery process ending: %s\nExplanation cloud-discovery process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLOUD-2-PROGRAM_EXIT: cloud-discovery process ending: [chars]Explanation Cloud-discovery process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLOUD-3
Error Message CLOUD-3-CFS_MERGE_OPERATION_FAILED Format: %sExplanation [chars1].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLOUD-3-CFS_OPERATION_FAILED Format: %s : %sExplanation [chars1] [chars2].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLOUD-3-CLOUD_CFS_MERGE_OPERATION_FAILED: [chars]Explanation [chars1].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CLOUD-3-CLOUD_CFS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CLOUD-3-CLOUD_FEATURE_MANAGER_ERROR: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for error using feature manager and fix the problem.
Error Message CLOUD-3-CLOUD_PSS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the pss operation and fix the problem.
Error Message CLOUD-3-FEATURE_MANAGER_ERROR Format: %s : %sExplanation [chars1] [chars2].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLOUD-3-PSS_OPERATION_FAILED Format: %s : %sExplanation [chars1] [chars2].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLOUD-6
Error Message CLOUD-6-CLOUD_DISCOVERY_DONE: discovery overExplanation Cloud-discovery started.
Recommended Action Check cloud membership.
Error Message CLOUD-6-CLOUD_DISCOVERY_STARTED: [chars] discovery startedExplanation Cloud-discovery started.
Recommended Action Check cloud-discovery status after sometime.
Error Message CLOUD-6-DISCOVERY_DONE Format: discovery over\nExplanation cloud-discovery started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLOUD-6-DISCOVERY_STARTED Format: %s discovery started\nExplanation cloud-discovery started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLP_XBAR Messages
This section contains the CLP_XBAR messages.
CLP_XBAR-2
Error Message CLP_XBAR-2-FR_CRC Format: %sExplanation Clipper received packets with CRC error from fabric.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLUSTER Messages
This section contains the CLUSTER messages.
CLUSTER-2
Error Message CLUSTER-2-ADD_FAIL Format: Cluster 0x%llx creation failed\nExplanation Cluster Creation Failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-CAP_ADD_FAIL Format: Failed to add cluster capability %dExplanation Cluster capability addition failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-CAP_DEL_FAIL Format: Failed to delete cluster capability %dExplanation Cluster capability deletion failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-CLUSTER_CAP_ADD_FAIL: Failed to add cluster capability [dec]Explanation Cluster capability addition failed.
Recommended Action No action is required.
Error Message CLUSTER-2-CLUSTER_CAP_DEL_FAIL: Failed to delete cluster capability [dec]Explanation Cluster capability deletion failed.
Recommended Action No action is required.
Error Message CLUSTER-2-DB_SYNC_FAIL Format: Cluster 0x%llx application %d dataset %d database synchronization failedExplanation Cluster database synchronization failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-DB_SYNC_FAIL_CLIENT Format: Client on node 0x%llx for cluster 0x%llx application %d dataset %d received database synchronization failedExplanation Cluster database synchronization failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-DB_SYNC_FAIL_MANAGER Format: Manager on node 0x%llx for cluster 0x%llx application %d dataset %d received database synchronization failedExplanation Cluster database synchronization failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-DB_SYNC_FAIL_SERVER Format: Server on node 0x%llx for cluster 0x%llx application %d dataset %d received database synchronization failedExplanation Cluster database synchronization failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-LEADER_ANNOUNCE Format: Node 0x%llx is the new Master of cluster 0x%llx of %d nodes\nExplanation Leader announcement of cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-LEAVE_REQ_FAIL Format: Node failed to send LEAVE request to Cluster 0x%llx\nExplanation Failed to send Leave Request.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-LEAVE_RESP_FAIL Format: Bad response to LEAVE request for Cluster 0x%llx\nExplanation Received Bad Leave response.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-LOCAL_NODE_EXIT Format: Local Node 0x%llx has left the Cluster 0x%llx\nExplanation Node is not part of cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-QUORUM_GAIN Format: Cluster 0x%llx now has quorum with %d nodes\nExplanation Cluster has quorum.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-QUORUM_LOSS Format: Cluster 0x%llx has lost quorum; number of nodes=%d\nExplanation Cluster has lost quorum.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-RGC_TRANSACTION_FAIL Format: Cluster 0x%llx RGC transaction application=%d dataset=%d failed reason=%sExplanation Cluster RGC transaction failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-2-TRANSPORT_FAIL Format: Cluster 0x%llx transport failed to send message from node 0x%llx to 0x%llx error=%d\nExplanation Cluster transport failed to send message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLUSTER-5
Error Message CLUSTER-5-ADD Format: Cluster 0x%llx added\nExplanation Cluster Added.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-DISABLED Format: CLUSTER DisabledExplanation CLUSTER Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-ENABLED Format: CLUSTER EnabledExplanation CLUSTER Service Enabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-NODE_ADD Format: Node 0x%llx added to cluster 0x%llx\nExplanation Node added to cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-NODE_JOIN Format: Node 0x%llx joined cluster 0x%llx\nExplanation Node joined cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-NODE_LEAVE Format: Node 0x%llx not in cluster 0x%llx\nExplanation Node not in cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-NODE_LEAVE_EXPLICIT Format: Remote Node 0x%llx has left the Cluster 0x%llx voluntarily\nExplanation Remote Node Left voLUNtarily.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-NODE_REMOVE Format: Node 0x%llx removed from cluster 0x%llx\nExplanation Node removed from cluster.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-REMOVE Format: Cluster 0x%llx removed\nExplanation Cluster removed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-RX_JOIN_REQ Format: Node 0x%llx received JOIN request from node=0x%llxExplanation Cluster received JOIN request.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-RX_JOIN_RESP Format: Node 0x%llx received JOIN response from node=0x%llx result=%sExplanation Cluster received JOIN response.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-RX_PROBE Format: Node 0x%llx received PROBE from node=0x%llxExplanation Cluster received PROBE message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-STARTED Format: CLUSTER 0x%llx StartedExplanation CLUSTER Started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-STOPPED Format: CLUSTER 0x%llx StoppedExplanation CLUSTER Stopped.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-TRANSPORT_DOWN Format: Cluster 0x%llx transport down for node=0x%llxExplanation Cluster Transport Connection DOWN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-TRANSPORT_UP Format: Cluster 0x%llx transport up for node=0x%llxExplanation Cluster Transport Connection UP.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-TX_JOIN_REQ Format: Node 0x%llx sending JOIN request to node=0x%llxExplanation Cluster sending JOIN request.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER-5-TX_JOIN_RESP Format: Node 0x%llx sending JOIN response to node=0x%llx result=%sExplanation Cluster sending JOIN request.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLUSTER_TEST_APP Messages
This section contains the CLUSTER_TEST_APP messages.
CLUSTER_TEST_APP-5
Error Message CLUSTER_TEST_APP-5-DISABLED Format: CLUSTER_TEST_APP DisabledExplanation CLUSTER_TEST_APP Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER_TEST_APP-5-ENABLED Format: CLUSTER_TEST_APP EnabledExplanation CLUSTER_TEST_APP Service nabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER_TEST_APP-5-TEST_STARTED Format: Traffic test startedExplanation CLUSTER_TEST_APP Test started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CLUSTER_TEST_APP-5-TEST_STOPPED Format: Traffic test stoppedExplanation CLUSTER_TEST_APP Test stopped.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CMOND Messages
This section contains the CMOND messages.
CMOND-2
Error Message CMOND-2-CMOND_ALERT_MSG: [chars]Explanation Alert message.
Recommended Action No action is required.
Error Message CMOND-2-CMOND_ERROR_MSG: [chars]Explanation Error message.
Recommended Action No action is required.
CMPPROXY Messages
This section contains the CMPPROXY messages.
CMPPROXY-2
Error Message CMPPROXY-2-LOG_CMP_IS_NOT_UP: Connectivity Management processor (on module [dec]) did not come upExplanation Connectivity Management processor is not sending heartbeats on this module.
Recommended Action No action is required.
Error Message CMPPROXY-2-LOG_CMP_UP: Connectivity Management processor(on module [dec]) is now UPExplanation Connectivity Management processor has come up and is exchanging heartbeats with CP on this supervisor slot.
Recommended Action No action is required.
Error Message CMPPROXY-2-LOG_CMP_WENT_DOWN: Connectivity Management processor (on module [dec]) went DOWNExplanation Connectivity Management processor has either gone down or is not sending heartbeats for a long time.
Recommended Action No action is required.
CMPPROXY-5
Error Message CMPPROXY-5-LOG_CMP_AAA_FAILURE: Authentication failed for a login from CMP (on module [dec])Explanation A login attempt has been denied access from Connectivity management processor (CMP) as authentication did not succeed.
Recommended Action No action is required.
Error Message CMPPROXY-5-MALLOC_FAILURE Format: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CMPPROXY-5-MALLOC_FAILURE: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action No action is required.
CMPPROXY-6
Error Message CMPPROXY-6-LOG_CMP_AAA_SUCCESS: Authentication succeeded for a login from CMP (on module [dec])Explanation A login attempt has succeeded from Connectivity management processor (CMP) in getting access as AAA succeeded.
Recommended Action No action is required.
CMTMDL Messages
This section contains the CMTMDL messages.
CMTMDL-2
Error Message CMTMDL-2-DB_UNLOCK_FAILED Format: Failed to unlock the database for session:%sExplanation Session-Manager failed to unlock the database for session: [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CMTMDL-3
Error Message CMTMDL-3-ALLOC_FAILED Format: Failed in File:%s Line:%d for type %d size %dExplanation SDM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP Messages
This section contains the COPP messages.
COPP-1
Error Message COPP-1-COPP_DROPS1: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-1-DROPS1 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-2
Error Message COPP-2-COPP_DROPS2: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-2-COPP_INIT_FAIL: CoPP Initialization failed: [chars]Explanation CoPP Initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-2-COPP_MTS_FAIL: Failed to do MTS operation: [chars]Explanation The system has failed to do an MTS operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-2-COPP_NO_PINST: Control-plane is unprotected.Explanation There isn't any policy configured to protect control-plane.
Recommended Action No action is required.
Error Message COPP-2-DROPS2 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-2-INIT_FAIL Format: CoPP Initialization failed: %sExplanation CoPP Initialization failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-2-MTS_FAIL Format: Failed to do MTS operation: %sExplanation The system has failed to do an MTS operation. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-2-NO_PINST Format: Control-plane is unprotected.Explanation There isn't any policy configured to protect control-plane.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-3
Error Message COPP-3-ALLOC_FAIL Format: Memory allocation failure: %sExplanation Failed to allocate required memory. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-3-COPP_ALLOC_FAIL: Memory allocation failure: [chars]Explanation Failed to allocate required memory. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_DROPS3: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-3-COPP_PPF_FAIL: Error during PPF operation: [chars]Explanation The system has failed to do a PPF operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_PSS_FAIL: Error during PSS operation: [chars]Explanation The system has failed to do a PSS operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-DROPS3 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-3-PPF_FAIL Format: Error during PPF operation: %sExplanation The system has failed to do a PPF operation. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-3-PSS_FAIL Format: Error during PSS operation: %sExplanation The system has failed to do a PSS operation. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-4
Error Message COPP-4-COPP_DROPS4: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-4-DROPS4 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-5
Error Message COPP-5-COPP_DISABLED: COPP DisabledExplanation COPP Service Disabled.
Recommended Action No action is required.
Error Message COPP-5-COPP_DROPS5: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-5-COPP_ENABLED: COPP EnabledExplanation COPP Service nabled.
Recommended Action No action is required.
Error Message COPP-5-COPP_INIT: COPP initializedExplanation COPP Service Initialized.
Recommended Action No action is required.
Error Message COPP-5-DISABLED Format: COPP DisabledExplanation COPP Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-5-DROPS5 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-5-ENABLED Format: COPP EnabledExplanation COPP Service nabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-5-INIT Format: COPP initializedExplanation COPP Service Initialized.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-6
Error Message COPP-6-COPP_DROPS6: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-6-COPP_POLICY_ATTACHED: CoPP policy has been attached to control plane interface.Explanation CoPP policy has been attached to control plane interface.
Recommended Action No action is required.
Error Message COPP-6-COPP_POLICY_DETACHED: CoPP policy has been detached from control plane interface.Explanation CoPP policy has been detached from control plane interface.
Recommended Action No action is required.
Error Message COPP-6-DROPS6 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-6-POLICY_ATTACHED Format: CoPP policy has been attached to control plane interface.Explanation CoPP policy has been attached to control plane interface.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message COPP-6-POLICY_DETACHED Format: CoPP policy has been detached from control plane interface.Explanation CoPP policy has been detached from control plane interface.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
COPP-7
Error Message COPP-7-COPP_DROPS7: CoPP drops exceed threshold in class: [chars], check show policy-map interface control-plane for more info.Explanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action No action is required.
Error Message COPP-7-DROPS7 Format: CoPP drops exceed threshold in class: %sExplanation There are CoPP drops, [chars] tell which class has dropped packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CORE-DMON Messages
This section contains the CORE-DMON messages.
CORE-DMON-2
Error Message CORE-DMON-2-MODULE_COREDUMP_DONE: kernel coredump completed on module:[dec]Explanation Kernel coredump finishing on a module.
Recommended Action No action is required.
Error Message CORE-DMON-2-MODULE_COREDUMP_STARTED: kernel coredump started on module:[dec]Explanation Kernel coredump starting on a module.
Recommended Action No action is required.
CORE-DMON-3
Error Message CORE-DMON-3-NO_SPACE: Failed to save core file [chars]. Try removing existing core files.Explanation Not enough space to save new core files.
Recommended Action No action is required.
CORE_DMON Messages
This section contains the CORE_DMON messages.
CORE_DMON-2
Error Message CORE_DMON-2-MODULE_COREDUMP_DONE Format: kernel coredump completed on module:%d\nExplanation kernel coredump finishing on a module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CORE_DMON-2-MODULE_COREDUMP_STARTED Format: kernel coredump started on module:%d\nExplanation kernel coredump starting on a module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CPPA_MGR Messages
This section contains the CPPA_MGR messages.
CPPA_MGR-3
Error Message CPPA_MGR-3-ENABLE_VB_FAILURE: Virtual service blade [dec] could not be [chars]. Error: [chars]Explanation The requested virtual blade operation could not be completed.
Recommended Action No action is required.
Error Message CPPA_MGR-3-NO_HB_REBOOT: No heartbeat from agent service. Nexus1010 is rebootedExplanation No heartbeat from agent service. Nexus1010 is rebooted.
Recommended Action No action is required.
Error Message CPPA_MGR-3-REMOTE_ILO_REBOOT: Remote mgmt feature rebooted other Nexus1010 using ILOExplanation Remote mgmt feature rebooted other Nexus1010 using ILO.
Recommended Action No action is required.
Error Message CPPA_MGR-3-RESTORE_FAILURE: Agent version could not be restored to make versions matchExplanation The previous agent version could not be restored. The system needs to be reinstalled to recover.
Recommended Action No action is required.
Error Message CPPA_MGR-3-SOME_PNIC_FAILURE: Not all the Nexus1010 physical NICs are detected. Check for failureExplanation Not all the physical NICs are detected. Check for failure.
Recommended Action No action is required.
Error Message CPPA_MGR-3-UNDO_WRITE_ERASE: Undo Write Erase: [chars]Explanation The software undo write erase result:.
Recommended Action No action is required.
Error Message CPPA_MGR-3-UPGRADE_FAILED: Upgrade failed: [chars]Explanation The software upgrade could not complete because of the errors.
Recommended Action No action is required.
Error Message CPPA_MGR-3-VERSION_MISMATCH: Agent version mismatch detected. System will be reloadedExplanation The cppa_mgr and the underlying agent are not running the same software version.
Recommended Action No action is required.
Error Message CPPA_MGR-3-WRITE_ERASE: Write Erase: [chars]Explanation The software write erase result:.
Recommended Action No action is required.
CPPA_MGR-5
Error Message CPPA_MGR-5-REMOTE_VB_HA_FAILURE: Operation failed in standby for virtual service blade [dec]: [chars]Explanation An error occurred while processing a command from active at standby.
Recommended Action No action is required.
Error Message CPPA_MGR-5-REMOTE_VB_IMG_FAILURE: Could not verify image in standby for virtual service blade [dec] creation: [chars]Explanation An error occurred while processing image required for vb creation at standby.
Recommended Action No action is required.
Error Message CPPA_MGR-5-UPGRADE_COMPLETE: Upgrade completed successfullyExplanation The software upgrade completed with no errors.
Recommended Action No action is required.
Error Message CPPA_MGR-5-UPGRADE_START: Upgrade started. Image: [chars]Explanation A software upgrade has been initiated by the user.
Recommended Action No action is required.
Error Message CPPA_MGR-5-VB_DEPLOYED: Virtual service blade [chars] deployedExplanation Virtual service blade deployed on nexus1010 successfully.
Recommended Action No action is required.
Error Message CPPA_MGR-5-VB_REMOVED: Virtual service blade [chars] removedExplanation Virtual service blade removed by user.
Recommended Action No action is required.
Error Message CPPA_MGR-5-VB_RESTARTED: Virtual service blade [chars] restartedExplanation Virtual service blade restarted by user.
Recommended Action No action is required.
Error Message CPPA_MGR-5-VB_SHUT: Virtual service blade [chars] moved into shut stateExplanation Virtual service blade shut by user.
Recommended Action No action is required.
CRDCFG Messages
This section contains the CRDCFG messages.
CRDCFG-2
Error Message CRDCFG-2-SRV_CRIT Format: %sExplanation CardConfig CRITICAL ERROR.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CRDCFG-3
Error Message CRDCFG-3-ERR Format: %sExplanation CardConfig error mesage.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCFG-3-MSG Format: %sExplanation CardConfig log mesage.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCFG-3-SRV_ERR Format: %sExplanation CardConfigServer error mesage.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCFG-3-SRV_MSG Format: %sExplanation CardConfigServer log mesage.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CRDCLIENT Messages
This section contains the CRDCLIENT messages.
CRDCLIENT-2
Error Message CRDCLIENT-2-CARDCL_CRIT Format: %sExplanation CardClient Critical Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCLIENT-2-ONL Format: %sExplanation Online Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCLIENT-2-REG Format: %sExplanation CardClient Console Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCLIENT-2-SSE Format: %sExplanation CardClient Console Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CRDCLIENT-3
Error Message CRDCLIENT-3-CARDCL_ERR Format: %sExplanation CardClient Error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CRDCLIENT-3-CARDCL_INFO Format: %sExplanation CardClient Flow Message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CREDITMON-SLOT# Messages
This section contains the CREDITMON-SLOT# messages.
CREDITMON-SLOT#-2
Error Message CREDITMON-SLOT#-2-SYSERR_CREDITMON_APP_EXITED: [chars]Explanation Credit Monitor application exited.
Recommended Action No action is required.
Error Message CREDITMON-SLOT#-2-SYSERR_CREDITMON_MTS_INIT_ERR: [chars]Explanation Credit Monitor error binding to MTS.
Recommended Action No action is required.
CTS Messages
This section contains the CTS messages.
CTS-2
Error Message CTS-2-CTS_AUTHENT_FAILURE: CTS Authentication failure on Port [chars] (CTS Failure Reason: [chars] [chars])Explanation Fibre-Channel Authentication failure on Port [chars].(Reason Code [chars] Detail [chars]). Check password configurations and ensure appropriate security modes on this port as well as peer port.
Recommended Action No action is required.
Error Message CTS-2-CTS_FIPS_BYPASS_TEST_FAILED: FIPS bypass test failed for interface: [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-CTS_SAP_FAILED: SAP exchange failed on interface [chars]. (Reason: [chars])Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-CTS_SAP_REKEY_FAILED: SAP exchange failed on interface [chars]. (Reason: [chars])Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-DBG_INIT_FAILED: Debug Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-FC2_E_INIT_FAILED: Fibre-Channel Initialization of an E_Port failed ( [chars] )Explanation CTS Manager has been unable to initialize with the FC-2 E-Port infrastructure.
Recommended Action No action is required.
Error Message CTS-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an F_Port failed ( [chars] )Explanation CTS Manager has been unable to initialize with the FC-2 F-Port infrastructure.
Recommended Action No action is required.
Error Message CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT Format: Received an unexpected/unknown FC-2 frame on %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT: Received an unexpected/unknown FC-2 frame on [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-FIPS_BYPASS_TEST_FAILED Format: FIPS bypass test failed for interface: %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-FSMU_INIT_FAILED: State Machine Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-IPC_INIT_FAILED: IPC (Inter Process Communication) Initialization failed ( [chars] )Explanation CTS Manager has been unable to initialize with the IPC infrastructure.
Recommended Action No action is required.
Error Message CTS-2-LICENSE_UNAVAILABLE Format: License:%s unavailableExplanation License of [chars] is unavailable. Service will exit now.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service exitingExplanation License of [chars] is unavailable. Service will exit now.
Recommended Action Install the license file to continue using the feature.
Error Message CTS-2-MEM_FAILED Format: Memory operations failed File: %s Line %d for size 0x%x bytesExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-MEM_FAILED: Memory operations failed File: [chars] Line [dec] for size [hex] bytesExplanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-POST_INIT_FAILED: Post-Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_ENFORCEMENT_FAILED Format: Failed to %s RBACL enforcement on %s %luExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-RBACL_ENFORCEMENT_FAILED: Failed to [chars] RBACL enforcement on [chars] %luExplanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_ENFORCEMENT_FAILED: RBACL enforcement failed on [chars] [dec]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_LC_INSERT_FAILED Format: RBACL programming failed for inserted module %dExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-RBACL_LC_INSERT_FAILED: RBACL programming failed for inserted module [dec]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_TCAM_SPACE_NOT_ENOUGH Format: Not enough free space left on TCAMExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-RBACL_TCAM_SPACE_NOT_ENOUGH: Not enough free space left on TCAMExplanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_UNABLE_PARSE_ACE Format: Unable to parse RBACL ACE substring: %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-RBACL_UNABLE_PARSE_ACE: Unable to parse RBACL ACE substring: [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_UPDATE_FAILED Format: Failed to %s RBACL %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-2-RBACL_UPDATE_FAILED: Failed to [chars] RBACL [chars]Explanation The system has detected an error.
Recommended Action No action is required.
CTS-3
Error Message CTS-3-DOT1X_AUTHC_FAILED Format: DOT1X authentication failed on port: %sExplanation DOT1X authentication failed on the port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-3-DOT1X_AUTHC_FAILED: DOT1X authentication failed on port: [chars]Explanation DOT1X authentication failed on the port.
Recommended Action No action is required.
CTS-5
Error Message CTS-5-CTS_IP_SGT_MAP_DELETE: IP-SGT mapping deleted for [chars] on [chars] %luExplanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-5-CTS_IP_SGT_MAP_UPDATE: [chars] assigned SGT [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-5-CTS_IP_SGT_MAP_UPDATE: [chars] assigned SGT [dec]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-5-IP_SGT_MAP_DELETE Format: IP-SGT mapping deleted for %s on %s %luExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-5-IP_SGT_MAP_UPDATE Format: %s assigned SGT %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CTS-6
Error Message CTS-6-CTS_FIPS_BYPASS_TEST_PASSED: FIPS bypass test passed for interface: [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-6-FIPS_BYPASS_TEST_PASSED Format: FIPS bypass test passed for interface: %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-6-SXP_STATE_CHANGE Format: CTS SXP %sExplanation The system has detected an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CTS-6-SXP_STATE_CHANGE: CTS SXP [chars]Explanation The system has detected an error.
Recommended Action No action is required.
DC3_XBC Messages
This section contains the DC3_XBC messages.
DC3_XBC-2
Error Message DC3_XBC-2-PROC_INITFAIL Format: Process initialization failed due to %s.Explanation XBAR_CLIENT process has failed initialization.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DCEFIB-SLOT# Messages
This section contains the DCEFIB-SLOT# messages.
DCEFIB-SLOT#-0
Error Message DCEFIB-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed!Explanation DCEFIB failed to initialize CLI infrastructure\sbackendlibrary.Thisisafatalerror.'
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization failed!Explanation DCEFIB failed to initialize timer library. This is a fatal error.
Recommended Action No action is required.
DCEFIB-SLOT#-2
Error Message DCEFIB-SLOT#-2-DCEFIB_MEM_ALLOC: Memory allocation failed. [chars]Explanation Memory allocation failed. This is a critical failure.
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-2-DCEFIB_RECOVERY_ERROR: Error in Recovery: [chars]Explanation DCEFIB failed to recover after a re-start. This is a fatal error.
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-2-U2FIB_ERR: [chars]Explanation L2mp unicast fib encountered an error:.
Recommended Action No action is required.
DCEFIB-SLOT#-6
Error Message DCEFIB-SLOT#-6-INITIALIZED: Internal state created [chars]Explanation DCEFIB has created its internal state stateless/stateful [chars].
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-6-U2FIB_INFO: [chars]Explanation L2mp unicast fib notice:.
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-6-VDC_CREATED: VDC [dec] createdExplanation Request to create VDC [dec] in DCEFIB was successful.
Recommended Action No action is required.
Error Message DCEFIB-SLOT#-6-VDC_REMOVED: VDC [dec] RemovedExplanation DCEFIB has successfully removed VDC [dec] from its databases.
Recommended Action No action is required.
DDAS Messages
This section contains the DDAS messages.
DDAS-2
Error Message DDAS-2-ALLOC_FAILED Format: Memory allocation failed for size:%d type:%dExplanation Memory allocation failed for size [dec] type [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-2-INIT_FAILED Format: %sExplanation An error occurred during initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DDAS-3
Error Message DDAS-3-CFS_OPER_FAILED Format: %sExplanation An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-CLEAR_FAILED Format: %sExplanation An error occurred while clearing the session. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-COMMIT_FAILED Format: %sExplanation An error occurred while committing the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-COMMIT_REJECTED Format: %sExplanation Commit request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-LOCK_FAILED Format: %sExplanation An error occurred while acquiring the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-LOCK_REJECTED Format: %sExplanation Lock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_ACTIVATION_FAILED Format: %sExplanation An error occurred while activating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_ACTIVATION_REJECTED Format: %sExplanation Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_FAILED Format: %sExplanation An error occurred during merge operation. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_MREQ_REJECTED Format: %sExplanation MREQ received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_MRESP_REJECTED Format: %sExplanation MRESP received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_VALIDATION_FAILED Format: %sExplanation An error occurred while validating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MERGE_VALIDATION_REJECTED Format: %sExplanation Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-MTS_OPER_FAILED Format: %sExplanation An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-PSS_OPER_FAILED Format: %sExplanation An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-UNLOCK_FAILED Format: %sExplanation An error occurred while releasing the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-UNLOCK_REJECTED Format: %sExplanation Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-VALIDATION_FAILED Format: %sExplanation An error occurred while validating the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-3-VALIDATION_REJECTED Format: %sExplanation Validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DDAS-6
Error Message DDAS-6-CLEAR_FAILED_INFO Format: %sExplanation An error occurred while clearing the session. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-COMMIT_FAILED_INFO Format: %sExplanation An error occurred while committing the database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-IMPORT_DEFINITION_CONFLICT Format: Fcalias %s could not be imported due to definition conflictExplanation Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-IMPORT_MEMBER_TYPE_CONFLICT Format: Fcalias %s could not be imported due to having unsupported member typeExplanation Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-IMPORT_NAME_CONFLICT Format: Fcalias %s could not be imported due to name conflictExplanation Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-IMPORT_NUM_MEMBERS_CONFLICT Format: Fcalias %s could not be imported due to having unsupported number of membersExplanation Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-LOCK_FAILED_INFO Format: %sExplanation An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-MERGE_ACTIVATION_FAILED_INFO Format: %sExplanation An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-MERGE_VALIDATION_FAILED_BUSY Format: %sExplanation Merged database could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-MERGE_VALIDATION_REJECTED_BUSY Format: %sExplanation Merged database received from the remote switch could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-UNLOCK_FAILED_INFO Format: %sExplanation An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DDAS-6-VALIDATION_ABORTED Format: %sExplanation Local validation is aborted. [chars] indicates the reason why validation is aborted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEBUGPROXY Messages
This section contains the DEBUGPROXY messages.
DEBUGPROXY-6
Error Message DEBUGPROXY-6-SSM_DEBUG_PROXY_COMMON: SSM debug proxy [chars] [dec]Explanation General SSM debug proxy information.
Recommended Action No action is required.
DEV_LOG Messages
This section contains the DEV_LOG messages.
DEV_LOG-3
Error Message DEV_LOG-3-ERROR: [chars]Explanation Dev_log_lc encountered an error.
Recommended Action No action is required.
DEV_LOG-SLOT# Messages
This section contains the DEV_LOG-SLOT# messages.
DEV_LOG-SLOT#-4
Error Message DEV_LOG-SLOT#-4-DEV_LOG_LC_ERROR: [chars]Explanation Dev_log_lc encountered an error.
Recommended Action No action is required.
DEV_LOG_LC Messages
This section contains the DEV_LOG_LC messages.
DEV_LOG_LC-3
Error Message DEV_LOG_LC-3-ERROR Format: %sExplanation dev_log_lc encountered an error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE-ALIAS Messages
This section contains the DEVICE-ALIAS messages.
DEVICE-ALIAS-2
Error Message DEVICE-ALIAS-2-ALLOC_FAILED: Memory allocation failed for size:[dec] type:[dec]Explanation Memory allocation failed for size [dec] type [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-2-INIT_FAILED: [chars]Explanation An error occurred during initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE-ALIAS-3
Error Message DEVICE-ALIAS-3-CFS_OPER_FAILED: [chars]Explanation An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-CLEAR_FAILED: [chars]Explanation An error occurred while clearing the session. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-COMMIT_FAILED: [chars]Explanation An error occurred while committing the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-COMMIT_REJECTED: [chars]Explanation Commit request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-LOCK_FAILED: [chars]Explanation An error occurred while acquiring the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-LOCK_REJECTED: [chars]Explanation Lock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_ACTIVATION_FAILED: [chars]Explanation An error occurred while activating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_ACTIVATION_REJECTED: [chars]Explanation Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_FAILED: [chars]Explanation An error occurred during merge operation. [chars] indicates the reason for failure.
Recommended Action Compare device-alias configuration with the other switches in the fabric, resolve the conflicts if any and commit the changes.
Error Message DEVICE-ALIAS-3-MERGE_MREQ_REJECTED: [chars]Explanation MREQ received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_MRESP_REJECTED: [chars]Explanation MRESP received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_VALIDATION_FAILED: [chars]Explanation An error occurred while validating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_VALIDATION_REJECTED: [chars]Explanation Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MTS_OPER_FAILED: [chars]Explanation An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-PSS_OPER_FAILED: [chars]Explanation An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-UNLOCK_FAILED: [chars]Explanation An error occurred while releasing the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-UNLOCK_REJECTED: [chars]Explanation Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-VALIDATION_FAILED: [chars]Explanation An error occurred while validating the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-VALIDATION_REJECTED: [chars]Explanation Validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE-ALIAS-6
Error Message DEVICE-ALIAS-6-CLEAR_FAILED_INFO: [chars]Explanation An error occurred while clearing the session. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-COMMIT_FAILED_INFO: [chars]Explanation An error occurred while committing the database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-IMPORT_DEFINITION_CONFLICT: Fcalias [chars] could not be imported due to definition conflictExplanation Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.
Recommended Action Resolve the conflict and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_MEMBER_TYPE_CONFLICT: Fcalias [chars] could not be imported due to having unsupported member typeExplanation Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members.
Recommended Action Make sure that the fcalias has Port WWN based members and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_NAME_CONFLICT: Fcalias [chars] could not be imported due to name conflictExplanation Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.
Recommended Action Resolve the conflict and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_NUM_MEMBERS_CONFLICT: Fcalias [chars] could not be imported due to having unsupported number of membersExplanation Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member.
Recommended Action Make sure that the fcalias has exactly one member and issue the import command again.
Error Message DEVICE-ALIAS-6-LOCK_FAILED_INFO: [chars]Explanation An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_ACTIVATION_FAILED_INFO: [chars]Explanation An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_VALIDATION_FAILED_BUSY: [chars]Explanation Merged database could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_VALIDATION_REJECTED_BUSY: [chars]Explanation Merged database received from the remote switch could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-UNLOCK_FAILED_INFO: [chars]Explanation An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-VALIDATION_ABORTED: [chars]Explanation Local validation is aborted. [chars] indicates the reason why validation is aborted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE_TEST Messages
This section contains the DEVICE_TEST messages.
DEVICE_TEST-2
Error Message DEVICE_TEST-2-ASIC_REG_CHECK_FAIL Format: Module %d has failed test %s %d times on device %s %s %d %s due to error %sExplanation The online diagnostic ASICRegisterCheck test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test [chars] [dec] times on device [chars] [chars] [dec] [chars] due to error [chars]Explanation The online diagnostic ASICRegisterCheck test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test [chars] [dec] times on device [chars] [chars] [dec] frontpanel ports affected [chars] due to error [chars]Explanation The online diagnostic ASICRegisterCheck test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-COMPACT_FLASH_FAIL Format: Module %d has failed test %s %d times on device Compact Flash due to error %sExplanation The online diagnostic CompactFlash test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-COMPACT_FLASH_FAIL: Module [dec] has failed test [chars] [dec] times on device Compact Flash due to error [chars]Explanation The online diagnostic CompactFlash test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-CRYPTO_DEVICE_FAIL Format: Module %d has failed test %s %d times on Crypto device due to error %sExplanation The online diagnostic CryptoDevice test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-CRYPTO_DEVICE_FAIL: Module [dec] has failed test [chars] [dec] times on Crypto device due to error [chars]Explanation The online diagnostic CryptoDevice test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-EOBC_FAIL Format: Module %d has failed test %s on EOBC due to error %sExplanation The online diagnostic EOBC test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC due to error [chars]Explanation The online diagnostic EOBC test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-FAN_MOD_FAIL Format: Module %d has failed test %s %d times on System Mgmt Bus for chassis %s instance %d due to error %s error number 0x%08XExplanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-FAN_MOD_FAIL: Module [dec] has failed test [chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error [chars] error number [hex]Explanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-MALLOC_FAILURE Format: Memory allocation failedExplanation Device Test process could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-MALLOC_FAILURE: Memory allocation failedExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-MGMT_PORT_SKIP Format: Module %d has skipped test %s on Management Port due to error %sExplanation The online diagnostic ManagementPort test is skipped.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] on Management Port due to error [chars]Explanation The online diagnostic ManagementPort test is skipped.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-NVRAM_FAIL Format: Module %d has failed test %s %d times on device NVRAM due to error %sExplanation The online diagnostic NVRAM test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-NVRAM_FAIL: Module [dec] has failed test [chars] [dec] times on device NVRAM due to error [chars]Explanation The online diagnostic NVRAM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-OBFL_FAIL Format: Module %d has failed test %s %d times on device OBFL due to error %sExplanation The online diagnostic OBFL test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-OBFL_FAIL: Module [dec] has failed test [chars] [dec] times on device OBFL due to error [chars]Explanation The online diagnostic OBFL test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-POWER_SUPPLY_FAIL Format: Module %d has failed test %s %d times on System Mgmt Bus for chassis %s instance %d due to error %s error number 0x%08XExplanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-POWER_SUPPLY_FAIL: Module [dec] has failed test [chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error [chars] error number [hex]Explanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL Format: Module %d has failed test %s %d times on device Primary BootROM due to error %sExplanation The online diagnostic PrimaryBootROM test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL: Module [dec] has failed test [chars] [dec] times on device Primary BootROM due to error [chars]Explanation The online diagnostic PrimaryBootROM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-PWR_MGMT_BUS_FAIL Format: Module %d has failed test %s %d times on device Power Mgmt Bus on slot %d due to error %s error number 0x%08XExplanation The online diagnostic PwrMgmtBus test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module [dec] has failed test [chars] [dec] times on device Power Mgmt Bus on slot [dec] due to error [chars] error number [hex]Explanation The online diagnostic PwrMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-RTC_FAIL Format: Module %d has failed test %s %d times on device RealTimeClock due to error %sExplanation The online diagnostic RealTimeClock test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-RTC_FAIL: Module [dec] has failed test [chars] [dec] times on device RealTimeClock due to error [chars]Explanation The online diagnostic RealTimeClock test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL Format: Module %d has failed test %s %d times on device Secondary BootROM due to error %sExplanation The online diagnostic SecondaryBootROM test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL: Module [dec] has failed test [chars] [dec] times on device Secondary BootROM due to error [chars]Explanation The online diagnostic SecondaryBootROM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL Format: Module %d has failed test %s %d times on device Spine Control Bus on slot %d due to error %s error number 0x%08XExplanation The online diagnostic SpineControlBus test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL: Module [dec] has failed test [chars] [dec] times on device Spine Control Bus on slot [dec] due to error [chars] error number [hex]Explanation The online diagnostic SpineControlBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-STANDBY_LOOPBACK_TEST_FAIL Format: Module %d has failed test %s %d times on %s %d due to error %sExplanation The online diagnostic StandbyFabricLoopback test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-STANDBY_LOOPBACK_TEST_FAIL: Module [dec] has failed test [chars] [dec] times on [chars] [dec] due to error [chars]Explanation The online diagnostic StandbyFabricLoopback test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-TWOWIRE_STW_FAIL Format: Module %d has failed test %s %d times on Status Bus on slot %d due to error %sExplanation The online diagnostic Status bus test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-TWOWIRE_STW_FAIL: Module [dec] has failed test [chars] [dec] times on Status Bus on slot [dec] due to error [chars]Explanation The online diagnostic Status bus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-USB_FAIL Format: Module %d has failed test %s %d times on device USB due to error %sExplanation The online diagnostic USB test has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-2-USB_FAIL: Module [dec] has failed test [chars] [dec] times on device USB due to error [chars]Explanation The online diagnostic USB test has failed.
Recommended Action No action is required.
DEVICE_TEST-3
Error Message DEVICE_TEST-3-STANDBY_TEST_GET_DIAG_VQI_FAIL: Standby test get diag vqi failed due to error [hex]Explanation Device Test StandbyLoopback Test failed get vqi.
Recommended Action No action is required.
Error Message DEVICE_TEST-3-STANDBY_TEST_GET_SPINE_FAIL: Standby test get spines failed due to error [hex]Explanation Device Test StandbyFabricLoopback Test get spine failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-3-STANDBY_TEST_INIT_FAIL: Init for standby test failed due to error [hex]Explanation Device Test StandbyFabricLoopback Test failed init process.
Recommended Action No action is required.
Error Message DEVICE_TEST-3-STANDBY_TEST_MTS_FAIL: Mts Init for standby test failed due to error [hex]Explanation Device Test StandbyFabricLoopback Test failed mts init.
Recommended Action No action is required.
Error Message DEVICE_TEST-3-STANDBY_TEST_SOCKET_FAIL: Standby test socket error [chars]: [hex]Explanation Device Test StandbyFabricLoopback Test Socket error.
Recommended Action No action is required.
DEVICE_TEST-4
Error Message DEVICE_TEST-4-THREAD_CREATE_FAIL Format: Thread creation failedExplanation Device Test process could not create threads.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-4-THREAD_CREATE_FAIL: Thread creation failedExplanation Device Test process could not create threads.
Recommended Action No action is required.
Error Message DEVICE_TEST-4-TIMER_CREATE_FAIL Format: Timer creation failedExplanation Device Test process could not create timer.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-4-TIMER_CREATE_FAIL: Timer creation failedExplanation Device Test process could not create timer.
Recommended Action No action is required.
Error Message DEVICE_TEST-4-TIMER_START_FAIL Format: Timer start failedExplanation Device Test process could not start timer.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-4-TIMER_START_FAIL: Timer start failedExplanation Device Test process could not start timer.
Recommended Action No action is required.
DEVICE_TEST-5
Error Message DEVICE_TEST-5-NOTICE_TEST Format: Memory allocation failed noticeExplanation Device Test process could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-5-NOTICE_TEST: Memory allocation failed noticeExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
DEVICE_TEST-6
Error Message DEVICE_TEST-6-INFO_TEST Format: Memory allocation failed infoExplanation Device Test process could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE_TEST-6-INFO_TEST: Memory allocation failed infoExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
DFTM Messages
This section contains the DFTM messages.
DFTM-3
Error Message DFTM-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB Entry: [chars]Explanation DFTM failed to program BDDB Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table Entry: [chars]Explanation DFTM failed to program BD Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 Consistency Table Entry: [chars]Explanation DFTM failed to program L2L3 Consistency Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast FTag Table Entry: [chars]Explanation DFTM failed to program Multicast Ftag Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT Table Entry: [chars]Explanation DFTM failed to program SGT DGT Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN Translation Table Entry: [chars]Explanation DFTM failed to program VLAN Translation Table.
Recommended Action No action is required.
DFTM-SLOT# Messages
This section contains the DFTM-SLOT# messages.
DFTM-SLOT#-2
Error Message DFTM-SLOT#-2-DFTM_INTF_NOT_FOUND: Interface [chars] not found in DFTM database [chars]Explanation DFTM database does not have the interface.
Recommended Action No action is required.
Error Message DFTM-SLOT#-2-DFTM_INVALID_FTAG_NUM: DFTM received invalid number of FTags [dec] from M2RIBExplanation DFTM recvd invalid number of FTags from M2RIB.
Recommended Action No action is required.
Error Message DFTM-SLOT#-2-DFTM_PC_NUM_MEMB_INVALID: DFTM received invalid number of PC members [dec] from ELTMExplanation DFTM recvd invalid number of PC members from ELTM.
Recommended Action No action is required.
Error Message DFTM-SLOT#-2-DFTM_PC_NUM_MEMB_INVALID: DFTM recieved invalid number of PC members [dec] from ELTMExplanation DFTM recvd invalid number of PC members from ELTM.
Recommended Action No action is required.
Error Message DFTM-SLOT#-2-DFTM_VLAN_NOT_FOUND: VLAN [dec] not found in DFTM database [chars]Explanation DFTM database does not have the VLAN.
Recommended Action No action is required.
DFTM-SLOT#-3
Error Message DFTM-SLOT#-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB EntryExplanation DFTM failed to program BDDB Entry.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table EntryExplanation DFTM failed to program BD Table Entry.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_LAYER: Invalid Port Layer Received for interface: [chars]Explanation Invalid Port Layer Received for interface.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_MODE: Invalid Port Mode Received for interface: [chars]Explanation Invalid Port Mode Received for interface.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_TYPE: Invalid Port Type Received for interface: [chars]Explanation Invalid Port Type Received for interface.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_IFIDX_TYPE_ERROR: Failed to get type for interface: [chars]Explanation Failed to get type for the interface.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 Consistency Table EntryExplanation DFTM failed to program L2L3 Consistency Table Entry.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast FTag Table EntryExplanation DFTM failed to program Multicast Ftag Table Entry.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT Table EntryExplanation DFTM failed to program SGT DGT Table Entry.
Recommended Action No action is required.
Error Message DFTM-SLOT#-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN Translation Table EntryExplanation DFTM failed to program VLAN Translation Table.
Recommended Action No action is required.
DHCP_SNOOP Messages
This section contains the DHCP_SNOOP messages.
DHCP_SNOOP-2
Error Message DHCP_SNOOP-2-DHCP_SNOOP_PROGRAM_EXIT: [chars]Explanation DHCP snoop process did an abnormal exit.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-INITFAIL Format: DHCP Daemon Initialization failed: %sExplanation DHCP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-2-INITFAIL: DHCP Daemon Initialization failed: [chars]Explanation DHCP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-PROGRAM_EXIT Format: %sExplanation DHCP snoop process did an abnormal exit.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-2-PSSERROR Format: %sExplanation DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-2-PSSERROR: [chars]Explanation DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-REGPARTREE Format: Unable to register par tree: %sExplanation Could not register par tree. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-2-REGPARTREE: Unable to register par tree: [chars]Explanation Could not register par tree. [chars] explains the reason for the failure.
Recommended Action No action is required.
DHCP_SNOOP-3
Error Message DHCP_SNOOP-3-ALLOCFAIL Format: Heap Memory allocation failed: %sExplanation DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-ASSERTION_FAILED Format: %s:%dExplanation DHCP Snoop process has hit an assert condition at file [chars] line number [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-ASSERTION_FAILED: [chars]:[dec]Explanation DHCP Snoop process has hit an assert condition at file [chars] line number [dec].
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-DHCPDENIEDARP Format: ARP frame denied due to DHCP snooping binding on interface %s vlan %d sender mac %s sender ip %s target mac %s target ip %s.Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-DHCPDENIEDARP: ARP frame denied due to DHCP snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target mac [chars] target ip [chars].Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-DHCPRATELIMIT Format: Interface %s has been error disabled due to excessive ingress rate %d of DHCP packets.Explanation [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-DHCPRATELIMIT: Interface [chars] has been error disabled due to excessive ingress rate [dec] of DHCP packets.Explanation [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-HWPGMFAILURE Format: Hardware programming has failed: %sExplanation Hardware programming has failed. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-HWPGMFAILURE: Hardware programming has failed: [chars]Explanation Hardware programming has failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-INVDHCPPKTS Format: Validation errors while processing DHCP packet received on interface %s vlan %d Reason:%s. Dropping the packetExplanation Validation errors DHCP packet receieved on the interface [chars] vlan [%d]. Reason:[chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-INVDHCPPKTS: Validation errors while processing DHCP packet received on interface [chars] vlan [dec] Reason:[chars]. Dropping the packetExplanation Validation errors DHCP packet receieved on the interface [chars] vlan [[dec]]. Reason:[chars].
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-MTSERROR Format: %sExplanation DHCP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-MTSERROR: [chars]Explanation DHCP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PKTDROP Format: Packet dropped. Reason - %sExplanation Dropping the packet. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-PKTDROP: Packet dropped. Reason - [chars]Explanation Dropping the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PKTRECVFAIL Format: Failed to receive packet - %sExplanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-PKTRECVFAIL: Failed to receive packet - [chars]Explanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PKTSENDFAIL Format: Failed to send packetExplanation The system has failed to send the packet. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-PKTSENDFAIL: Failed to send packet, - [chars]Explanation The system has failed to send the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-SOCKBINDFAIL Format: Failed to bind to raw socket - %sExplanation Failed to bind to socket. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-SOCKBINDFAIL: Failed to bind to raw socket - [chars]Explanation Failed to bind to socket. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-SOCKOPENFAIL Format: Failed to open socket for receiving DHCP packets - %sExplanation An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-3-SOCKOPENFAIL: Failed to open socket for receiving DHCP packets - [chars]Explanation An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.
Recommended Action No action is required.
DHCP_SNOOP-4
Error Message DHCP_SNOOP-4-ACL_DENY: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-ACL_PERMIT: [dec] ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-DHCP_SNOOPING_DENY: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-DHCP_SNOOPING_PERMIT: [dec] ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-ERROR_DISABLED Format: Interface %s has moved to error disabled state due to excessive rate %d of ingress ARP packetsExplanation Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-4-ERROR_DISABLED: Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packetsExplanation Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets.
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-INVALID_ARP: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
DHCP_SNOOP-6
Error Message DHCP_SNOOP-6-DAIVLANDISABLE Format: DAI disabled on vlan %dExplanation Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DAIVLANDISABLE: DAI disabled on vlan [dec]Explanation Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DAIVLANENABLE Format: DAI enabled on vlan %dExplanation Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DAIVLANENABLE: DAI enabled on vlan [dec]Explanation Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPBINDSYNC Format: Binding entry with MAC %s interface %s VLAN %d IP address %s and lease time %d secs is synced.Explanation Binding entry identified by [chars] has been synced. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPBINDSYNC: Binding entry with MAC [chars] interface [chars] VLAN [dec] IP address [chars] and lease time [dec] secs is synced.Explanation Binding entry identified by [chars] has been synced. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPEXIT Format: DHCP Daemon shutting down gracefully.Explanation DHCP Daemon is shutting down gracefully.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPEXIT: DHCP Daemon shutting down gracefully.Explanation DHCP Daemon is shutting down gracefully.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPHOSTADD Format: A new Host is %s connected to interface %s in VLAN %d and is allocated IP address %s for %d secs.Explanation A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPHOSTADD: A new Host is [chars] connected to interface [chars] in VLAN [dec] and is allocated IP address [chars] for [dec] secs.Explanation A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPLEASEEXPIRE Format: Lease expired for host %s having IP address %s connected to interface %s in VLAN %d for lease %d secs.Explanation The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPLEASEEXPIRE: Lease expired for host [chars] having IP address [chars] connected to interface [chars] in VLAN [dec] for lease [dec] secs.Explanation The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPPERMITTEDARP Format: ARP frame permitted due to DHCP snooping binding on interface %s vlan %d sender mac %s sender ip %s target mac %s target ip %s.Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPPERMITTEDARP: ARP frame permitted due to DHCP snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target mac [chars] target ip [chars].Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPPKTFWD Format: Gracefully forwarding DHCP packet. Reason: %sExplanation Gracefully forwarding DHCP packet. reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPPKTFWD: Gracefully forwarding DHCP packet. Reason: [chars]Explanation Gracefully forwarding DHCP packet. reason [chars].
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPPKTFWD: Gracefully forwarding DHCP packet. reason:[chars]Explanation Gracefully forwarding DHCP packet. reason [chars].
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPUP Format: DHCP Daemon Up.Explanation DHCP Daemon was created successfully and is up and running.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-DHCPUP: DHCP Daemon Up.Explanation DHCP Daemon was created successfully and is up and running.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INFO Format: %sExplanation An event during switchover. [chars] explains the reason for the failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-INFO: [chars]Explanation An event during switchover. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INTFDISABLE Format: IP Src Guard disabled on intf %sExplanation IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-INTFDISABLE: IP Src Guard disabled on intf [chars]Explanation IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INTFENABLE Format: IP Src Guard enabled on intf %sExplanation IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-INTFENABLE: IP Src Guard enabled on intf [chars]Explanation IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-NONDHCPPKTFWD Format: Non DHCP packet with src port:%d dst port:%d on intf:%s vlan:%d. Forwarding on %sExplanation Non DHCP packet arrived with UDP src/dst ports [dec], [dec] on interface [chars], vlan [dec]. Forwarding the packet on [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-NONDHCPPKTFWD: Non DHCP packet with src port:[dec] dst port:[dec] on intf:[chars] vlan:[dec]. Forwarding on [chars]Explanation Non DHCP packet arrived with UDP src/dst ports [dec], [dec] on interface [chars], vlan [dec]. Forwarding the packet on [chars].
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-OPT82INSTFAIL Format: %s %sExplanation Insertion of Option82 suboptions failed. [chars] tells the failure. [chars] explains the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-OPT82INSTFAIL: [chars] [chars]Explanation Insertion of Option82 suboptions failed. [chars] tells the failure. [chars] explains the reason for failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-VLANDISABLE Format: DHCP Snooping disabled on vlan %dExplanation DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-VLANDISABLE: DHCP Snooping disabled on vlan [dec]Explanation DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-VLANENABLE Format: DHCP Snooping enabled on vlan %dExplanation DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DHCP_SNOOP-6-VLANENABLE: DHCP Snooping enabled on vlan [dec]Explanation DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
DIAG_PORT_LB Messages
This section contains the DIAG_PORT_LB messages.
DIAG_PORT_LB-2
Error Message DIAG_PORT_LB-2-FIPS_RANDOM_ERROR Format: Random Number Generation FailureExplanation Random Number genration failed in FIPS module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-2-FIPS_RANDOM_ERROR: Random Number Generation FailureExplanation Random Number genration failed in FIPS module.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE Format: LC Inserted request response send to Module Manager failed . Error:%sExplanation Failed to send the response for LC insertion to Module Manager.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE: LC Inserted request response send to Module Manager failed . Error:[chars]Explanation Failed to send the response for LC insertion to Module Manager.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-LIF_GET_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic LIF id.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-MALLOC_FAILURE: [chars]([dec]) Memory allocation failed.Explanation Port Loopback test process could not allocate enough memory.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL Format: Module:%d Test:PortLoopback failed %d consecutive times. Faulty module:%s %s Error:%sExplanation PortLoopback test failed on the module consecutively.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL: Module:[dec] Test:PortLoopback failed [dec] consecutive times. Faulty module:[chars] [chars] Error:[chars]Explanation PortLoopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL: Module:[dec] Test:PortLoopback failed [dec] consecutive times. Faulty module:[chars] affected ports:[chars] Error:[chars]Explanation PortLoopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-PROC_INIT_FAILURE: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed in process initialization.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL Format: Module:%d Test:RewriteEngine Loopback failed %d consecutive times. Faulty module:%s %s Error:%sExplanation Rewrite Engine Loopback test failed on the module consecutively.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[chars] [chars] Error:[chars]Explanation Rewrite Engine Loopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[chars] affected ports:[chars] Error:[chars]Explanation Rewrite Engine Loopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-SNAKE_TEST_LOOPBACK_TEST_FAIL Format: Module:%d Test:SnakeLoopback failed %d consecutive times. Faulty module:%s affected ports:%s Error:%sExplanation Snake test failed on the module consecutively.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-2-SNAKE_TEST_LOOPBACK_TEST_FAIL: Module:[dec] Test:SnakeLoopback failed [dec] consecutive times. Faulty module:[chars] affected ports:[chars] Error:[chars]Explanation Snake test failed on the module consecutively.
Recommended Action No action is required.
DIAG_PORT_LB-3
Error Message DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE Format: %s. Module:%d Error:%s.Explanation Forwarding path setup for port loopback tests failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE: [chars]. Module:[dec] Error:[chars].Explanation Forwarding path setup for port loopback tests failed.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-DIAG_PKT_SEND_FAILURE: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed to send loopback packets.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-FSM_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-GET_DIAG_BD_FAIL: [chars]([dec]) Failed to get the BD for Diag VLAN:[dec]. Error:[chars].Explanation Failed to get the BD corresponding to the Diag VLAN.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-IFINDEX_LIB_FAILURE: [chars]([dec]) [chars] [chars]:[hex] [chars] [chars]Explanation Port Loopback test process failed in if_index library API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-INVALID_TEST_REQUEST: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to get test request info.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-INVALID_TEST_RUN: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to get the current test run information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-MTS_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PDB_LIB_API_ERROR Format: Failed to %s. Error:%d.Explanation The port loopback test was not able to get chassis information.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-PDB_LIB_API_ERROR: Failed to [chars]. Error:[dec].Explanation The port loopback test was not able to get chassis information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PIXM_LIB_ERROR: [chars]([dec]) Failed to convert [chars]:[hex] to [chars]. Error:[chars]Explanation Port Loopback test process failed to convert port ifindex <-> port index.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send request to configure port ifindex:[dec] for port loopback testExplanation Failed to configure/restore the port to do/cleanup port loopback testing.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PORT_CLIENT_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in Port Client API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RESULT_ADD_FAILURE: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to add the port test result.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RESULT_SEND_FAILURE: [chars]([dec]) [chars]Explanation Port Loopback test process failed to send the test results.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL Format: Module:%d Test:RewriteEngine Loopback Spine path:%d failed %d consecutive times. Error:%sExplanation Rewrite Engine Loopback test failed on the spine path consecutively.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL: Module:[dec] Test:RewriteEngine Loopback Spine path:[dec] failed [dec] consecutive times. Error:[chars]Explanation Rewrite Engine Loopback test failed on the spine path consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-SOCKET_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed in socket operations.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-STATS_LIB_ERROR: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed in stats infra lib API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-TEST_RES_SEND_FAIL Format: Failed to send %s test results back to Diagnostics Infrastucture. Error:%s.Explanation The port loopback test was not able to send the test results.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-TEST_RES_SEND_FAIL: Failed to send [chars] test results back to Diagnostics Infrastucture. Error:[chars].Explanation The port loopback test was not able to send the test results.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-TIMER_LIB_ERROR: [chars]([dec]) [chars]Explanation Port Loopback test process timer handling failure.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-VLAN_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic VLAN information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-VQI_GET_FAIL Format: Failed to get the Diag VQi from XBM. Error:%sExplanation Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-VQI_GET_FAIL: Failed to get the Diag VQi from XBM. Error:[chars]Explanation Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL Format: Failed to conigure the XBAR mask while running the RewriteEngineLoopback test. Error:%s. Module:%d could have gone offlineExplanation Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL: Failed to conigure the XBAR mask while running the RewriteEngineLoopback test. Error:[chars]. Module:[dec] could have gone offlineExplanation Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline.
Recommended Action No action is required.
DIAG_PORT_LB-4
Error Message DIAG_PORT_LB-4-MTS_LIB_ERROR: [chars]([dec]) [chars]. Warning:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-4-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send request to configure port ifindex:[dec] for port loopback testExplanation Failed to configure/restore the port to do/cleanup port loopback testing.
Recommended Action No action is required.
DIAG_PORT_LB-5
Error Message DIAG_PORT_LB-5-DIAG_PORT_LB_DISABLED: DIAG_PORT_LB DisabledExplanation DIAG_PORT_LB Service Disabled.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-5-DIAG_PORT_LB_ENABLED: DIAG_PORT_LB EnabledExplanation DIAG_PORT_LB Service nabled.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-5-DISABLED Format: DIAG_PORT_LB DisabledExplanation DIAG_PORT_LB Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAG_PORT_LB-5-ENABLED Format: DIAG_PORT_LB EnabledExplanation DIAG_PORT_LB Service nabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DIAGCLIENT Messages
This section contains the DIAGCLIENT messages.
DIAGCLIENT-2
Error Message DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE Format: /* MODULE_IDExplanation Bootup Test completed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE: Module <[dec]> Bootup Test <[chars]> has reported <[chars]>Explanation Bootup Test completed.
Recommended Action Nothing to be done if the test reports SUCCESS otherwise copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN Format: Test <%s> has been disabled as a part of default EEM actionExplanation Informational Syslog.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN: Test <[chars]> has been disabled as a part of default EEM actionExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-2-PSS_READ_FAILURE Format: /* MODULE_ID */ Read from PSS failed on Module <%d>Explanation Read operation from PSS store failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-2-PSS_READ_FAILURE: Read from PSS failed on Module <[dec]>Explanation Read operation from PSS store failed.
Recommended Action No action is required.
Error Message DIAGCLIENT-2-PSS_WRITE_FAILURE Format: /* MODULE_ID */ Write to PSS failed on Module <%d>Explanation Write operation on PSS store failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]>Explanation Write operation on PSS store failed.
Recommended Action No action is required.
DIAGCLIENT-3
Error Message DIAGCLIENT-3-DIAG_HM_FAIL Format: Module <%d> Health Monitoring Test <%s> has failed. Please use 'show diagnostic result <target>' to see test resultsExplanation A Health Monitoring Test has reported failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-3-DIAG_HM_FAIL: Module <[dec]> Health Monitoring Test <[chars]> has failed. Please use 'show diagnostic result <target>' to see test resultsExplanation A Health Monitoring Test has reported failure.
Recommended Action Ensure the line card is firmly in the slot, reseat if necessary, and attempt to run the test again if the line card is not seated properly in the slot. If the line card was properly seated in the slot, copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS Format: Module <%d> Test <%s> has failed more than <%d> number of timesExplanation Ondemand test has failed more than configured number of times.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS: Module <[dec]> Test <[chars]> has failed more than <[dec]> number of timesExplanation Ondemand test has failed more than configured number of times.
Recommended Action Copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-3-PER_PORT_TEST_FAIL: Module <[dec]> Test <[chars]> has failed on Ports <[chars]> Please use 'show diagnostic result <target>' to see test resultsExplanation Per Port Test has failed on the above all ports.
Recommended Action No action is required.
DIAGCLIENT-4
Error Message DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT Format: Received LC offline event for the current slot:%d. Ignoring itExplanation Informational Syslog.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT: Received LC offline event for the current slot:[dec]. Ignoring itExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-4-MTS_SEND_FAILURE Format: MTS send failedExplanation MTS send reports failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-4-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest slot: [dec], dest SAP: [dec], error-id: [hex]Explanation MTS send reports failure.
Recommended Action No action is required.
DIAGCLIENT-5
Error Message DIAGCLIENT-5-CALLOC_FAILURE Format: Memory allocation failedExplanation DiagClient process could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-CALLOC_FAILURE: Memory allocation failedExplanation DiagClient process could not allocate enough memory.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_FINISH Format: Module %d: Ondemand test %s finishedExplanation Informational Syslog.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_FINISH: Module [dec]: Ondemand test [chars] finishedExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_START Format: Module %d: Ondemand test %s startedExplanation Informational Syslog.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_START: Module [dec]: Ondemand test [chars] startedExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_STOP Format: Module %d: Ondemand test %s stoppedExplanation Informational Syslog.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-DIAG_ONDEMAND_TEST_STOP: Module [dec]: Ondemand test [chars] stoppedExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-DIAG_SCHED_COMPLETE Format: Module <%d> Test <%s> has completed Scheduled TestingExplanation A scheduled Test was completed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-DIAG_SCHED_COMPLETE: Module <[dec]> Test <[chars]> has completed Scheduled TestingExplanation A scheduled Test was completed.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-ONDEMAND_FAIL Format: Module <%d> Test <%s> has failed in Test_Iteration <%d>Explanation The specified test has reported FAILURE in this Iteration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-ONDEMAND_FAIL: Module <[dec]> Test <[chars]> has failed in Test_Iteration <[dec]>Explanation The specified test has reported FAILURE in this Iteration.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-ONDEMAND_SUCCESS Format: Module <%d> Test <%s> has completed successfully in Test_Iteration <%d>Explanation The specified test has reported SUCCESS in this Iteration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-ONDEMAND_SUCCESS: Module <[dec]> Test <[chars]> has completed successfully in Test_Iteration <[dec]>Explanation The specified test has reported SUCCESS in this Iteration.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-PER_PORT_TEST_FAIL Format: /* MODULE_IDExplanation Per Port Test has failed on the above all ports.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGCLIENT-5-PER_PORT_TEST_FAIL: Module <[dec]> Test <[chars]> has failed on Ports <[chars]> Please use 'show diagnostic result <target>' to see test resultsExplanation Per Port Test has failed on the above all ports.
Recommended Action No action is required.
DIAGMGR Messages
This section contains the DIAGMGR messages.
DIAGMGR-2
Error Message DIAGMGR-2-MTS_SEND_FAILURE Format: MTS send failedExplanation MTS send reports failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-2-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest slot: [dec], dest SAP: [dec], error-id: [hex]Explanation MTS send reports failure.
Recommended Action No action is required.
Error Message DIAGMGR-2-PSS_DELETE_FAILURE Format: Read from PSS failed on Module <%d>Explanation Read operation from PSS store failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-2-PSS_DELETE_FAILURE: Read from PSS failed on Module <[dec]>Explanation Read operation from PSS store failed.
Recommended Action No action is required.
Error Message DIAGMGR-2-PSS_WRITE_FAILURE Format: Write to PSS failed on Module <%d>Explanation Write operation on PSS store failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]>Explanation Write operation on PSS store failed.
Recommended Action No action is required.
DIAGMGR-3
Error Message DIAGMGR-3-DIAG_MAJOR_DEFECT Format: Module <%d> Test <%s> detected a Major Error Please use 'show diagnostic result <target>' to see test resultsExplanation A major error was detected during diagnostic testing.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-3-DIAG_MAJOR_DEFECT: Module <[dec]> Test <[chars]> detected a Major Error Please use 'show diagnostic result <target>' to see test resultsExplanation A major error was detected during diagnostic testing.
Recommended Action Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-3-DIAG_MINOR_DEFECT Format: Module <%d> Test <%s> detected a Minor Error Please use 'show diagnostic result <target>' to see test resultsExplanation A mior error was detected during diagnostic testing.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-3-DIAG_MINOR_DEFECT: Module <[dec]> Test <[chars]> detected a Minor Error Please use 'show diagnostic result <target>' to see test resultsExplanation A mior error was detected during diagnostic testing.
Recommended Action Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-3-GET_CURR_SLOT_FAIL Format: Failed to get the current slot for the process. Error:%sExplanation The process initialization failed to get the current slot.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-3-GET_CURR_SLOT_FAIL: Failed to get the current slot for the process. Error:[chars]Explanation The process initialization failed to get the current slot.
Recommended Action This is an informational message stating that a process initialization failure.
DIAGMGR-4
Error Message DIAGMGR-4-CURR_SLOT_OFFLINE Format: Recevied an LC offline event for the current slot:%d. Ignoring itExplanation The process received an offline event for the slot it is running. Ignoring it.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-4-CURR_SLOT_OFFLINE: Recevied an LC offline event for the current slot:[dec]. Ignoring itExplanation The process received an offline event for the slot it is running. Ignoring it.
Recommended Action This is an informational message stating that an unexpected event has been encountered.
Error Message DIAGMGR-4-DISRPT_TST_START Format: Starting Test <%s> on Module <%d> is DisruptiveExplanation Starting a Disruptive Test can disturb the system's normal functionality.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-4-DISRPT_TST_START: Starting Test <[chars]> on Module <[dec]> is DisruptiveExplanation Starting a Disruptive Test can disturb the system's normal functionality.
Recommended Action Reset target module.
Error Message DIAGMGR-4-FIXED_INTRVL_CHANGED Format: /*TestName*/ The users are not allowed to change monitoring interval of Test <%s>Explanation The specified health monitoring test interval is not user-configurable and therefore cannot be changed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-4-FIXED_INTRVL_CHANGED: The users are not allowed to change monitoring interval of Test <[chars]>Explanation The specified health monitoring test interval is not user-configurable and therefore cannot be changed.
Recommended Action No action is required.The specific health monitoring interval is not user- configurable by design so nothing can be done to change the interval.
DIAGMGR-5
Error Message DIAGMGR-5-BOOTUP_CONF Format: /*COMPLETE/BYPASS*/ Diagnostic Bootup Level: <%s>Explanation Current Diagnostic BootUp Level being configure or changed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-BOOTUP_CONF: Diagnostic Bootup Level: <[chars]>Explanation Current Diagnostic BootUp Level being configure or changed.
Recommended Action No action is required.
Error Message DIAGMGR-5-CALLOC_FAILURE Format: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-CALLOC_FAILURE: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action No action is required.
Error Message DIAGMGR-5-CHANGE_ALWAYS_HM Format: Health Monitoring test <%s> in Module <%d> is a must run and cannot be modifiedExplanation The specified health monitoring test must be run and cannot be disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-CHANGE_ALWAYS_HM: Health Monitoring test <[chars]> in Module <[dec]> is a must run and cannot be modifiedExplanation The specified health monitoring test must be run and cannot be disabled.
Recommended Action No action is required.The specific health monitoring test cannot be disabled by design. The system is working properly.
Error Message DIAGMGR-5-HM_START Format: Health monitoring test <%s> for Module <%d>Explanation Health Monitoring Test started.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-HM_START: Health monitoring test <[chars]> for Module <[dec]>Explanation Health Monitoring Test started.
Recommended Action No action is required.
Error Message DIAGMGR-5-HM_STOP Format: Disabling health monitoring test <%s> for Module <%d>Explanation Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-HM_STOP: Disabling health monitoring test <[chars]> for Module <[dec]>Explanation Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command.
Recommended Action No action is required.
Error Message DIAGMGR-5-INTRVL_INCORRECT Format: Monitoring Interval is less than minimum of %d seconds required for Module <%d> test <%s>Explanation Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-INTRVL_INCORRECT: Monitoring Interval is less than minimum of [dec] seconds required for Module <[dec]> test <[chars]>Explanation Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set.
Recommended Action The system is working properly and no action is required. If you want to specify a smaller testing interval, the error message text provides the lowest possible configurable interval for the specified monitoring interval.
Error Message DIAGMGR-5-MODULE_MISSING Format: Diagnostic command issued on non-existing Module <%d>Explanation A line card could not be located in a slot where a diagnostic action was requested.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-MODULE_MISSING: Diagnostic command issued on non-existing Module <[dec]>Explanation A line card could not be located in a slot where a diagnostic action was requested.
Recommended Action Ensure the targeted line card is properly seated in the specified slot. If the line card is properly seated, ensure the correct slot was indicated in the command-line interface. If the line card is well-seated and the correct slot was specified, copy the error message exactly as it appears on the screen as well as the output of show tech-support and paste the output into a separate file. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-5-NONHM_AS_HM Format: The Test <%s> cannot be used as health monitoring testExplanation Non-HM test cannot be scheduled to run as a Health Monitoring test.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-5-NONHM_AS_HM: The Test <[chars]> cannot be used as health monitoring testExplanation Non-HM test cannot be scheduled to run as a Health Monitoring test.
Recommended Action No action is required.
DIAGMGR-6
Error Message DIAGMGR-6-BOOTUP_DIAG_OK Format: /* MODULE_ID */ Module <%d>: Passed Online DiagnosticsExplanation The diagnostic tests did not detect any error on the card.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-6-BOOTUP_DIAG_OK: Module <[dec]>: Passed Online DiagnosticsExplanation The diagnostic tests did not detect any error on the card.
Recommended Action This is an informational message stating that the line card passed the diagnostic tests.
Error Message DIAGMGR-6-BOOTUP_TEST_STARTED Format: /* MODULE_IDExplanation Starting bootup testing for above module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DIAGMGR-6-BOOTUP_TEST_STARTED: Module <[dec]>: Running [chars] DiagnosticsExplanation Starting bootup testing for above module.
Recommended Action No action is required.
DM Messages
This section contains the DM messages.
DM-2
Error Message DM-2-FC2_INITIALIZATION_FAILED Format: FC initialization sequence failedExplanation The fcdomain has not been able to complete the initialization sequence with the Fibre Channel subsystem. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-FC2_SET_SOCKOPT_DM_SOCK_FAILED Format: set sockopt to FC2 Service failedExplanation fcdomain has not been able to setsockopt to the FC2 module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-FC2BIND_FAILED Format: Bind to FC2 Service failedExplanation fcdomain has not been able to contact the FC2 module.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-FCID_PERSISTENT_TBL_COMPLETELY_FULL Format: FCID persistent table is completely fullExplanation The FCID persistent table is full. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table. No more entries can be saved as persistent FCIDs across reboots.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-INITIALIZATION_FAILED Format: Initialization sequence failedExplanation The fcdomain has not been able to complete the initialization sequence. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-MY_NON_VIRTUAL_DOM_CONFLICTS Format: During VSAN merge detected that the local switch has the same domain ID %d and WWN %s of another switchExplanation The system has detected that the local switch has the same domain ID [dec] and WWN [chars] of another switch.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-NON_VIRTUAL_DOMS_CONFLICTS Format: During VSAN merge detected conflict between two switches having the same non-virtual domain ID %d and the same WWN %sExplanation The system has detected that two switches have the same non-virtual domain ID [dec] and the same WWN [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-SYSBIND_FAILED Format: Bind to System Manager service failedExplanation fcdomain has not been able to contact the The system Manager.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-2-SYSMGR_INITIALIZATION_FAILED Format: System Manager initialization sequence failedExplanation The fcdomain has not been able to complete the initialization sequence with the The system Manager. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DM-3
Error Message DM-3-COMMITERRORLOCALINVALIDALLOWEDDOMS Format: A remote switch attempted to locally apply an illicit allowed domains configurationExplanation A remote switch attempted to locally apply an allowed domain's configuration that does not include all currently assigned domains or the locally configured domain.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-3-SDWRAPBIND_FAILED Format: Bind to debug server failedExplanation fcdomain feature has not been able to contact the debug service. Any problems occurring in the fcdomain feature will not be logged.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-3-SDWRAPHISTINIT_FAILED Format: Initialization of history message list failed.Explanation fcdomain feature has not been able to contact the debug history service. Any problems occurring in the fcdomain feature will not be logged to this debug history.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DM-4
Error Message DM-4-ALLOWED_DM_LIST_MOD_ON_SUBORDINATE Format: Allowed domain list for vsan %d modified on subordinate switch with fcdomain distribution enabledExplanation When distRIBution is enabled, it is recommended to modify the allow domain list on the principal switch only.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-4-FC2_CORRUPTED Format: Received malformed FC2 %s frameExplanation fcdomain received a malformed FC2-SWILS frame.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-4-FCID_PERSISTENT_TBL_ALMOST_FULL Format: FCID persistent table is almost fullExplanation fcdomain has 80% or more of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DM-5
Error Message DM-5-DOMAIN_TYPE_IS_PREFERRED Format: The domain ID type is currently configured as preferred in all the existing VSANsExplanation All the currently existing VSANs have the domain ID type configured as preferrored. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-FCID_PERSISTENT_TBL_HALF_FULL Format: FCID persistent table is half fullExplanation fcdomain has 50% of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-FCIDP_DISABLED Format: FCID persistency feature is currently not enabled in any of the existing VSANsExplanation All the currently existing VSANs have the FCID persistency feature disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-UNKNOWNDOMAININCFSDATAREQUEST Format: Received CFS Data request from unknown domain %d.Explanation A CFS Data request from the unknown domain [dec] has been received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-UNKNOWNDOMAININCFSLOCKREQUEST Format: Received CFS Lock request from unknown domain %d.Explanation A CFS Lock request from the unknown domain [dec] has been received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-UNKNOWNDOMAININCFSRELEASEREQUEST Format: Received CFS Release request from unknown domain %d.Explanation A CFS Release request from the unknown domain [dec] has been received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-5-UNKNOWNDOMAININUNKNOWNCFSREQUEST Format: Received CFS request from unknown domain %d.Explanation A CFS request from the unknown domain [dec] has been received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DM-6
Error Message DM-6-BF_STARTED Format: BF started by %sExplanation Build Fabric has been started in this VSAN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-CANNOTFREESINGLEFCID Format: Impossible to free single FCIDsExplanation Impossible to free single FCIDs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-CLEARLOCKNOTIFICATIONRECEIVED Format: Implict lock release.Explanation Lock has been implicitly released due to a clear session operation.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-DOMAINID_INVALID Format: Local domain ID invalidExplanation The local domain ID is invalid.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-DOMAINID_VALID Format: Local domain ID %d availableExplanation The domain ID [dec] is available.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-DOWNSTREAM_SWITCHED Format: Downstream interface has been fast-switched from %s to %sExplanation Because of a link failure the downstream interface has been fast-switched from [dec] to [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-EPORT_ALREADY_CREATED Format: Interface %s already createdExplanation Interface [chars] already created.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-EPORT_ALREADY_DOWN Format: Interface %s is already downExplanation Interface [chars] already down.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-EPORT_CLEANUP Format: Interface %s received cleanup requestExplanation fcdomain on interface [chars] has received a cleanup request.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-EPORT_CREATED Format: Creation of interface %sExplanation fcdomain is going to create interface [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-EPORT_DOWN Format: Interface %s is downExplanation fcdomain is going to remove interface [chars] from its database.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FABRICNAME_INVALID Format: Fabric name not availableExplanation Fabric name not available.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FABRICNAME_VALID Format: Fabric name %s availableExplanation Fabric name [chars] available.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCID_ASSIGNED Format: Assigned single FCID %02x:%02x:%02xExplanation Assigned single FCID [hex]:[hex]:[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCID_FREED Format: Freed single FCID %02x:%02x:%02xExplanation Freed single FCID [hex]:[hex]:[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCIDALREADYFREE Format: FCIDs already freeExplanation FCIDs already free.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCIDNOTSTORED Format: FCIDs not storedExplanation FCIDs not stored.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCIDP_ENABLED_DOM_TYPE_PREFERRED Format: FCID persistency is enabledExplanation The FCID persistency feature is enabled, but the domain ID type is configured as preferrored. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link. Should the domain ID change, all the FCIDs associated with it would be invalidated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCIDS_ASSIGNED Format: Assigned a sequence of 256 contiguous FCIDs starting from FCID %02x:%02x:%02xExplanation Assigned a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-FCIDS_FREED Format: Freed a sequence of 256 contiguous FCIDs starting from FCID %02x:%02x:%02xExplanation Freed a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-INCORRECTDOMAIN Format: Requested FCIDs with domain field different from local domainExplanation Requested FCIDs with domain field different from local domain.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-INCORRECTDOMAINRANGE Format: Requested FCIDs with domain field not in expected rangeExplanation Requested FCIDs with domain field not in expected range.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-INVALIDARG Format: Requested FCID of type 00.00.YYExplanation Requested FCID of type 00.00.YY, but specifying an entire area.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-NODOMAIN Format: Local domain not availableExplanation The local domain is not available yet.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-NOFREEFCID Format: No free FCIDsExplanation No free FCIDs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-OTHER_SIDE_VIRTUAL_IVR_DOMS_OVERLAPPING Format: During VSAN merge detected overlap with virtual IVR domain ID %d from across the linkExplanation The system has detected an overlap with the virtual IVR domain ID [dec] from across the link during an attempt to merge the local VSAN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-PSWSSTARTED Format: Principal Switch Selection startedExplanation fcdomain started a principal switch selection phase to elect a principal switch in this VSAN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-RCF_STARTED Format: RCF started by %sExplanation Reconfigure Fabric has been started in this VSAN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-REQSINGLEFCIDWITHINRESERVEDRANGE Format: Requested single FCIDs in area %d within the reserved rangeExplanation Requested single FCIDs in area [dec] within the reserved range.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-REQUESTEDFCIDNOTFREE Format: Requested FCIDs not freeExplanation Requested FCIDs not free.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-REQUESTEDFCIDRESERVED Format: Requested reserved FCIDsExplanation Requested reserved FCIDs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-REQUESTEDRESERVEDFCIDMISMATCH Format: Requested persistent FCIDsExplanation Requested persistent FCIDs, but there is a mismatch.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-SAME_WWNS_DIFFERENT_DOMS_CONFLICTS Format: During VSAN merge detected two switches with same WWN %s and different non-virtual domain IDs %d and %dExplanation The system has detected that two switches have the same WWN [chars], but different non-virtual domain IDs: [dec] and [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-TIMER_UNKNOWN Format: fcdomain has received a notification for an unknown timer expirationExplanation A timer unknown to fcdomain has expired.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-UPSTREAM_SWITCHED Format: Upstream interface has been fast-switched from %s to %sExplanation Because of a link failure the upstream interface has been fast-switched from [dec] to [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-UUIDNOSPACEFOUND Format: No available space to store the identity of the requestor the FCIDsExplanation No available space to store the identity of the requestor the FCIDs.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-6-VIRTUAL_IVR_DOMS_OVERLAPPING Format: During VSAN merge detected overlap with local virtual IVR domain ID %dExplanation The system has detected an overlap with the local virtual IVR domain ID [dec] during an attempt to merge the local VSAN.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DM-7
Error Message DM-7-EPORT_ALREADY_ISOLATED Format: Interface %s is already isolated or downExplanation fcdomain was going to isolate interface [chars], but the interface is already isolated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-7-FCID_IN_USE_PURGING_FOR_FICON_MGR Format: FICON needs to purge the persistent FCID tableExplanation There may be a problem in the sequence that shuts down all interfaces before fcdomain receives a request from FICON Manager to purge the persistent FCID table.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-7-FSM_FORBIDDEN_TRANSITION Format: fcdomain state machine has hit a forbidden transitionExplanation fcdomain state machine has tried to execute a forbidden transition.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-7-INTERFACERDY Format: Interface %s readyExplanation Interface [chars] is ready.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DM-7-PREACTIONTYPE_UNKNOWN Format: fcdomain state machine has hit an unknown pre-action typeExplanation An undefined pre-action type has been used.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DMM-SLOT# Messages
This section contains the DMM-SLOT# messages.
DMM-SLOT#-5
Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_SRVR_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Server FCID:[hex] are in the same zone. ALERT!!Explanation A New N-Port has come up which is zoned in the same zone as the Server.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_STG_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Storage FCID:[hex] are in the same zone. ALERT!!Explanation A New N-Port has come up which is zoned in the same zone as the Storage.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_SRVR_RSCN: Job Id:%Ld Server N-Port pWWN:0x%Lx [chars]Explanation An RSCN event was received for the Server associated with a Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_STG_RSCN: Job Id:%Ld N-Port pWWN:0x%Lx Storage:[chars] [chars]Explanation An RSCN event was received for the Storage associated with a Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_COMPLETE: Job Id:%Ld NumSession:[dec]Explanation Event indicating the completion of a Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR_LOST_SSM_PEER_CONNECTION: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job due to loss in ip connectivity to peer ssm.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_FINISH: Job Id:%Ld NumSession:[dec]Explanation Event indicating Finish-request for a Method-2 Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_START: Job Id:%Ld NumSession:[dec]Explanation Event indicating the start of a Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_STOP: Job Id:%Ld NumSession:[dec]Explanation Event indicating that the Data Migration Job was stopped by Administrator.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_TCP_CONNECTION_DOWN: Job Id:%Ld lost connection to peer [chars]. Job may be RESETExplanation Event indicating IP Connectivity loss to peer SSM. Affected Job may be RESET.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_COMPLETE: Job Id:%Ld NumSession:[dec]Explanation Event indicating the completion of a Data Migration Job Verification.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_ERROR: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job Verification due to an error.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_START: Job Id:%Ld NumSession:[dec]Explanation Event indicating the start of a Data Migration Job Verification.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_STOP: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job Verification by the user.
Recommended Action No action is required.
DOT1X Messages
This section contains the DOT1X messages.
DOT1X-2
Error Message DOT1X-2-DOT1X_INIT: Dot1x unable to startExplanation The system failed to create the Dot1x process.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-2-INIT Format: Dot1x unable to startExplanation The system failed to create the Dot1x process.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DOT1X-3
Error Message DOT1X-3-ERR_SPANDST Format: Dot1x can not be enabled on %s. It is configured as a SPAN Dest port.Explanation Dot1x and SPAN Dest ports are mutually exclusive features.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-ERR_SPANDST: It is configured as a SPAN Dest port.Explanation Dot1x and SPAN Dest ports are mutually exclusive features.
Recommended Action Disable SPAN destination port configuration first before reconfiguring Dot1x on the port.
Error Message DOT1X-3-INVALID_INPUT Format: Dot1x Interface parameter is Invalid on interface %s.Explanation The Dot1x interface parameter is out of the specified range or is invalid.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-INVALID_INPUT: Invalid on interface [chars].Explanation The Dot1x interface parameter is out of the specified range or is invalid.
Recommended Action Refer to the CLI help documentation to determine the valid 802.1x parameters.
Error Message DOT1X-3-MEM_UNAVAIL Format: Memory was not available to perform the 802.1X action.Explanation Insufficient system memory is available to perform the Dot1x Authentication.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-MEM_UNAVAIL: perform the 802.1X action.Explanation Insufficient system memory is available to perform the Dot1x Authentication.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message DOT1X-3-NOT_DOT1X_CAPABLE Format: Dot1x disabled on interface %s because it is not a physical Ethernet interface.Explanation Dot1x Authentication can only be enabled on physical Ethernet interfaces.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-NOT_DOT1X_CAPABLE: interface [chars] because it is not a physical Ethernet interface.Explanation Dot1x Authentication can only be enabled on physical Ethernet interfaces.
Recommended Action Enable Dot1x Authentication on physical Ethernet interfaces only.
Error Message DOT1X-3-SECURITY_VIOLATION Format: Security violation New MAC address %s is seen on interface %s in %s modeExplanation The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-SECURITY_VIOLATION: New MAC address [chars] is seen on interface [chars] in [chars] modeExplanation The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.
Recommended Action Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.
Error Message DOT1X-3-SM_INIT Format: Internal error while initializing state machine %sExplanation An attempt was made to initialize an invalid state machine.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-3-SM_INIT: Internal error while initializing state machine [chars], state [chars]: [chars]Explanation An attempt was made to initialize an invalid state machine.
Recommended Action Initialize dot1x state machine.
DOT1X-4
Error Message DOT1X-4-BADEVENT Format: Event %s is invalid for the current state %s: %s %sExplanation An attempt was made to post an event to a state machine that is invalid for the current state.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-BADEVENT: Event [chars] is invalid for the current state [chars]: [chars] [chars]Explanation An attempt was made to post an event to a state machine that is invalid for the current state.
Recommended Action Initialize dot1x state machine.
Error Message DOT1X-4-MAB_DISABLED Format: Interface %s is in Trunk modeExplanation MAB is not supported on Trunk port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-MAB_DISABLED: Interface [chars] is in Trunk mode, MAB is not supported on this portExplanation MAB is not supported on Trunk port.
Recommended Action To enable MAB make sure that port is not in trunk mode.
Error Message DOT1X-4-MAB_DISABLED_ON_PCM Format: Interface %s is a member of portchannelExplanation MAB is not supported on port channel member port.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-MAB_DISABLED_ON_PCM: Interface [chars] is a member of portchannel, MAB is not supported on this portExplanation MAB is not supported on port channel member port.
Recommended Action To enable MAB make sure that port is not member of port channel.
Error Message DOT1X-4-MULTIHOST_ON_PCM Format: Interface %s is a member of portchannelExplanation Current Port is a member of port channel, so dot1x host mode has to be in multi-host mode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-MULTIHOST_ON_PCM: Interface [chars] is a member of portchannel, dot1x host mode will be multi-host and changing it to single-host mode won't be supportedExplanation Current Port is a member of port channel, so dot1x host mode has to be in multi-host mode.
Recommended Action To change host mode, ensure that port is not a member of port channel.
Error Message DOT1X-4-PSEC_ON_PCM Format: Interface %s is a member port or portchannel interface with port security configrationExplanation Dot1x is not supported on member ports or port channel with port security configuration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-PSEC_ON_PCM: Interface [chars] is a member port or portchannel interface with port security configrationExplanation Dot1x is not supported on member ports or port channel with port security configuration.
Recommended Action Remove port security configuration on the member port or port channel interface.
Error Message DOT1X-4-STOPPED Format: Event %s ignored because the state machine is stopped: %s %sExplanation An attempt was made to post an event to a state machine that has already been stopped.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-STOPPED: Event [chars] ignored because the state machine is stopped: [chars] [chars]Explanation An attempt was made to post an event to a state machine that has already been stopped.
Recommended Action An internal error has occurred with the state machine. The traceback should indicate the guilty party.
Error Message DOT1X-4-TO_MULTIHOST Format: Interface %s is in trunk modeExplanation Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-4-TO_MULTIHOST: Interface [chars] is in trunk mode, dot1x host mode will be multi-host and changing it to single-host mode won't be supportedExplanation Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.
Recommended Action To change host mode, ensure that port is not in trunk mode.
DOT1X-5
Error Message DOT1X-5-DISABLED Format: dot1x DisabledExplanation dot1x Service Disabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-DISABLED_LIC_EXPIRED Format: Dot1x Disabled due to License ExpiryExplanation Dot1x Disabled due to License Expiry.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-DOT1X_DISABLED: dot1x DisabledExplanation Dot1x Service Disabled.
Recommended Action No action is required.
Error Message DOT1X-5-DOT1X_ENABLED: dot1x EnabledExplanation Dot1x Service Enabled.
Recommended Action No action is required.
Error Message DOT1X-5-DOT1X_NOTIF: [chars]Explanation Dot1x Notification.
Recommended Action No action is required.
Error Message DOT1X-5-ENABLED Format: dot1x EnabledExplanation dot1x Service Enabled.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-INVALID_EAPOL: packet body length [dec] interface [chars] MTU [dec]Explanation 802.1X received invalid EAPOL packet.
Recommended Action Verify source of EAPOL packets.
Error Message DOT1X-5-INVALID_MAC: broadcast or multicast mac address) [chars] is trying to authenticate.Explanation Authentication using 802.1x is not allowed for zero, broadcast, and multicast source MAC addresses.
Recommended Action Connect a Dot1x supported Host to the Dot1x enabled port.
Error Message DOT1X-5-NOTIF Format: %sExplanation Dot1x Notification.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-PAC_STATUS Format: PAC provisioning for the server %s through the vrf %s %sExplanation PAC provisioning status.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-PAC_STATUS: PAC provisioning for the server [chars] through the vrf [chars] [chars]Explanation PAC provisioning status.
Recommended Action No action is required.
Error Message DOT1X-5-SECURITY_VIOLATION: New MAC address [chars] is seen on interface [chars] in [chars] modeExplanation The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.
Recommended Action Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.
Error Message DOT1X-5-SESSION_CREATION Format: Dot1x authentication session initiated in interface %s using authentication method %sExplanation Dot1x authentication session has been created after successful authentication of supplicannot.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-SESSION_CREATION: Dot1x authentication session initiated in interface [chars] using authentication method [chars]Explanation Dot1x authentication session has been created after successful authentication of supplicannot.
Recommended Action No action is required.
Error Message DOT1X-5-SESSION_TERMINATION Format: Dot1x authentication session in interface %s using authentication method %s is terminated because of %s and port moved to %s stateExplanation Dot1x authentication session has been terminated.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-SESSION_TERMINATION: Dot1x authentication session in interface [chars] using authentication method [chars] is terminated because of [chars] and port moved to [chars] stateExplanation Dot1x authentication session has been terminated.
Recommended Action No action is required.
Error Message DOT1X-5-STATUS Format: Dot1x interface %s status changed from %s to %sExplanation Dot1x authenticator has changed its internal state.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DOT1X-5-STATUS: Dot1x interface [chars] status changed from [chars] to [chars]Explanation Dot1x authenticator has changed its internal state.
Recommended Action No action is required.
DPP_DEBUG Messages
This section contains the DPP_DEBUG messages.
DPP_DEBUG-2
Error Message DPP_DEBUG-2-DPP_CRIT Format: [DPP%d] %sExplanation a DPP generated a critical message.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPP_DEBUG-2-DPP_CRIT: [DPP[dec]] [chars]Explanation A DPP generated a critical message.
Recommended Action No action is required.
DPVM Messages
This section contains the DPVM messages.
DPVM-2
Error Message DPVM-2-ALLOC_FAILED Format: Memory allocation failed for size:%d for %sExplanation memory allocation failed for size [dec] for [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-2-ALLOC_FAILED: Memory allocation failed for size:[dec] for [chars]Explanation Memory allocation failed for size [dec] for [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-2-DPVM_DUPL_REJECT: [chars]Explanation Rejected duplicate pwwn query.
Recommended Action Dpvm overwrite-duplicate-pwwn.
Error Message DPVM-2-DUPL_REJECT Format: %sExplanation Rejected duplicate pwwn query.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DPVM-3
Error Message DPVM-3-DB_ERR Format: %sExplanation an error occurred during an DPVM database operation. [chars] indicates the reason for the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-DB_ERR: [chars]Explanation An error occurred during an DPVM database operation. [chars] indicates the reason for the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-DDAS_MODE_INVALID Format: %sExplanation DDAS mode Invalid. [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-DDAS_MODE_INVALID: [chars]Explanation DDAS mode Invalid. [chars].
Recommended Action Flip DDAS mode.
Error Message DPVM-3-INIT_FAIL Format: %sExplanation an error occurred during DPVM Initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-INIT_FAIL: [chars]Explanation An error occurred during DPVM Initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-MTS_ERR Format: %sExplanation an error occurred in processing of an MTS message. [chars] indicates the error that occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-MTS_ERR: [chars]Explanation An error occurred in processing of an MTS message. [chars] indicates the error that occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-PSS_ERR Format: %sExplanation an error occurred during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-PSS_ERR: [chars]Explanation An error occurred during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DPVM-4
Error Message DPVM-4-ACTIVATION_FAIL Format: %sExplanation Activation of DPVM device mappings failed due to [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-4-ACTIVATION_FAIL: [chars]Explanation Activation of DPVM device mappings failed due to [chars].
Recommended Action Correct the error and reactivate database again.
Error Message DPVM-4-FEATURE_DISABLED Format: %sExplanation DPVM is unavailable and disabled now.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-4-FEATURE_DISABLED: [chars]Explanation DPVM is unavailable and disabled now.
Recommended Action No action is required.
DPVM-6
Error Message DPVM-6-FEATURE_ENABLED Format: %sExplanation DPVM is available and enabled now.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-6-FEATURE_ENABLED: [chars]Explanation DPVM is available and enabled now.
Recommended Action No action is required.
Error Message DPVM-6-INFO Format: %sExplanation an event happened that affects DPVM. [chars] indicates the event.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-6-INFO: [chars]Explanation An event happened that affects DPVM. [chars] indicates the event.
Recommended Action No action is required.
DRAP Messages
This section contains the DRAP messages.
DRAP-2
Error Message DRAP-2-DRAP_LINK_BRINGUP_STALLED_STATIC: Link bringup stalled due to conflictsExplanation Interface is disabled due to conflicts.
Recommended Action No action is required.
Error Message DRAP-2-LINK_BRINGUP_STALLED_STATIC Format: Link bringup stalled due to conflictsExplanation Interface is disabled due to conflicts.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DRAP-4
Error Message DRAP-4-DRAP_INVALID_FTAG: Invalid ftag [dec] receivedExplanation Invalid ftag is received from remote.
Recommended Action No action is required.
Error Message DRAP-4-DRAP_INVALID_SWITCH_ID: Invalid switch-id [dec] receivedExplanation Invalid switch-id is received from remote.
Recommended Action No action is required.
Error Message DRAP-4-DRAP_LINK_BRINGUP_STALLED: Link bringup stalled due to conflictsExplanation Interface is disabled due to conflicts.
Recommended Action No action is required.
Error Message DRAP-4-INVALID_FTAG Format: Invalid ftag %d receivedExplanation Invalid ftag is received from remote.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-4-INVALID_SWITCH_ID Format: Invalid switch-id %d receivedExplanation Invalid switch-id is received from remote.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DRAP-6
Error Message DRAP-6-DRAP_LINK_BRINGUP_RESOLVE_COLLISION: Resolving Collision for switch-id [dec]Explanation Resolving Collision for switch-id.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_LINK_BRINGUP_STALLED: LINK bringup suspended for [dec] due to conflictsExplanation Link bring up temporarily suspended due to conflicts.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_LINK_BRINGUP_STALLED_CLEARED: LINK bringup cleared for [dec] after collision resolutionExplanation Link bring up temporarily suspended due to conflicts.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_NEW_ES_SWITCH_ID: New Emulated switch-id [chars] receivedExplanation New Emulated switch-id received.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_NEW_SWITCH_ID: New switch-id [chars] receivedExplanation New switch-id received.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_SWID_CHANGED: Switch-id [dec] is assigned with [chars] stateExplanation Local switch-id is changed.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_SWID_CONFLICTS: Switch-id [dec] is in conflict with device [chars]Explanation Local switch-id collision with other device.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_SWID_PRI_SEC_CHANGED: Switch-id [dec] is changed to [chars]Explanation Local switch-id status changed.
Recommended Action No action is required.
Error Message DRAP-6-DRAP_SWID_STATE_CHANGED: Switch-id [dec] status changed to [chars]Explanation Local switch-id status changed.
Recommended Action No action is required.
Error Message DRAP-6-LINK_BRINGUP_RESOLVE_COLLISION Format: Resolving Collision for switch-id %dExplanation Resolving Collision for switch-id.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-LINK_BRINGUP_STALLED Format: LINK bringup suspended for %d due to conflictsExplanation Link bring up temporarily suspended due to conflicts.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-LINK_BRINGUP_STALLED_CLEARED Format: LINK bringup cleared for %d after collision resolutionExplanation Link bring up temporarily suspended due to conflicts.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-NEW_ES_SWITCH_ID Format: New Emulated switch-id %s receivedExplanation New Emulated switch-id received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-NEW_SWITCH_ID Format: New switch-id %s receivedExplanation New switch-id received.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-SWID_CHANGED Format: Switch-id %d is assigned with %s stateExplanation Local switch-id is changed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-SWID_CONFLICTS Format: Switch-id %d is in conflict with device %sExplanation Local switch-id collision with other device.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-SWID_PRI_SEC_CHANGED Format: Switch-id %d is changed to %sExplanation Local switch-id status changed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DRAP-6-SWID_STATE_CHANGED Format: Switch-id %d status changed to %sExplanation Local switch-id status changed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DSTATS Messages
This section contains the DSTATS messages.
DSTATS-2
Error Message DSTATS-2-PSS_INIT_FAIL Format: pss initialization failed due to error: 0x%xExplanation dstats process pss initialization failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-2-PSS_INIT_FAIL: pss initialization failed due to error: [hex]Explanation Dstats process pss initialization failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
DSTATS-3
Error Message DSTATS-3-PSS_CREATE_FAIL Format: pss create runtime database failed due to error: 0x%xExplanation dstats process pss create runtime database failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_CREATE_FAIL: pss create runtime database failed due to error: [hex]Explanation Dstats process pss create runtime database failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_DELETE_FAIL Format: pss delete runtime entry key:0x%x failed due to error: 0x%xExplanation dstats process pss delete runtime entry key [hex] failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_DELETE_FAIL: pss delete runtime entry key:[hex] failed due to error: [hex]Explanation Dstats process pss delete runtime entry key [hex] failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_MAX_KEY_FAIL Format: pss set runtime max key failed due to error: 0x%xExplanation dstats process pss set runtime max key failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_MAX_KEY_FAIL: pss set runtime max key failed due to error: [hex]Explanation Dstats process pss set runtime max key failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_MAX_VALUE_FAIL Format: pss set runtime max value failed due to error: 0x%xExplanation dstats process pss set runtime max value failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_MAX_VALUE_FAIL: pss set runtime max value failed due to error: [hex]Explanation Dstats process pss set runtime max value failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_OPEN_FAIL Format: pss open runtime database failed due to error: 0x%xExplanation dstats process pss open runtime database failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_OPEN_FAIL: pss open runtime database failed due to error: [hex]Explanation Dstats process pss open runtime database failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_RELOAD_FAIL Format: pss reload runtime database failed due to error: 0x%xExplanation dstats process pss reload runtime database failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_RELOAD_FAIL: pss reload runtime database failed due to error: [hex]Explanation Dstats process pss reload runtime database failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_SNAPSHOT_DEBUG_FAIL Format: pss snapshot runtime debug to uri:%s failed due to error: 0x%xExplanation dstats process pss snapshot of runtime debug to uri [string] failed due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_SNAPSHOT_DEBUG_FAIL: pss snapshot runtime debug to uri:[chars] failed due to error: [hex]Explanation Dstats process pss snapshot of runtime debug to uri [string] failed due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_SNAPSHOT_FAIL Format: pss snapshot runtime to uri:%s failed due to error: 0x%xExplanation dstats process pss snapshot of runtime to uri [string] failed due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_SNAPSHOT_FAIL: pss snapshot runtime to uri:[chars] failed due to error: [hex]Explanation Dstats process pss snapshot of runtime to uri [string] failed due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
Error Message DSTATS-3-PSS_STORE_FAIL Format: pss store runtime entry key:0x%x val:0x%x failed due to error: 0x%xExplanation dstats process pss store runtime entry key [hex] value [hex] failure due to error [hex].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DSTATS-3-PSS_STORE_FAIL: pss store runtime entry key:[hex] val:[hex] failed due to error: [hex]Explanation Dstats process pss store runtime entry key [hex] value [hex] failure due to error [hex].
Recommended Action Collect more information by using the show flash command. See the pss system error codes for the information about the failure.
DT_HELPER Messages
This section contains the DT_HELPER messages.
DT_HELPER-2
Error Message DT_HELPER-2-MALLOC_FAILURE Format: Memory allocation failedExplanation GOLD Test Helper process could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
EIGRP Messages
This section contains the EIGRP messages.
EIGRP-2
Error Message EIGRP-2-ALLOC_URIB_ADD Format: eigrp_smalloc() failed for URIB add-route bufferExplanation Failed to allocateate URIB add-route buffer.
Recommended Action Configure the network or router to decrease the number of routes, or add additional memory to the router.
Error Message EIGRP-2-ALLOC_URIB_DEL Format: eigrp_smalloc() failed for URIB delete-route bufferExplanation Failed to allocateate URIB delete-route buffer.
Recommended Action Configure the network or router to decrease the number of routes, or add additional memory to the router.
Error Message EIGRP-2-API_INIT Format: Couldn't initialize %s APIExplanation EIGRP failed to open API to interact with the component.
Parameters: API name ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-BFD_API_FAIL Format: bfd_send_remove_sessionsExplanation Failed to send bfd remove sessions.
Recommended Action No action is required.
Error Message EIGRP-2-BFD_CREATE_SESSION_FAILED Format: BFD Session create failed.Explanation Failed to create BFD session.
Recommended Action No action is required.
Error Message EIGRP-2-CIB_CREATE_FAIL Format: eigrp_create_cib failed for context %sExplanation Failed to create specified context.
Parameters: Context name ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-CLEANUP_DREG Format: Failed to deregister with %s during eigrp_cleanup()Explanation Failed to deregister with specified service during process shutdown.
Parameters: Service name ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-CLI_INIT_FAILED Format: cli_init() failed in eigrp_init_cli()Explanation EIGRP could not register with the CLI server process.
Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-ERR_FREEBUF Format: Illegal memory free in function %sExplanation Illegal memory free detected.
Parameters: Function ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-ERR_URIB_TID Format: Can't determine context from URIB table id %ldExplanation Failed to determine context from URIB table id.
Parameters: Table id ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-ILL_FUNCCALL Format: Illegal call to function %sExplanation Illegal call to specified function.
Parameters: Function ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-ILL_POLICY_TYPE Format: Illegal policy type in %s()Explanation Illegal policy type in specified rpm callback.
Parameters: Function ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-ILL_WORKTYPE Format: Illegal work type %d ipigrp2_process_workq()Explanation Worker thread received illegal work type.
Parameters: Work type ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-ILLEGAL_TIMER_ID Format: Illegal timer-id used in mgd_timer_init_leaf(), timer-id: %dExplanation Illegal timer id was specified.
Parameters: Managed timer id ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-IM_REG_FAILED Format: im_register_client() failed in eigrp_init_im()Explanation EIGRP could not register with the IM process.
Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-INIT Format: %s failedExplanation EIGRP process initialization failed.
Parameters: Init function ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-IP_REG_FAILED Format: ip_register() failed in eigrp_init_ip()Explanation EIGRP could not register with the IP process.
Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-MGD_TIMER_CREATE_FAIL Format: Failed to create managed timer %dExplanation Failed to create specified managed timer.
Parameters: Managed timer id ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-MTS_BIND Format: mts_bind() failed in binding %s mts_q, error %sExplanation Failed in binding to specified mts queue with error.
Parameters: MTS queue name, Error string ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-MTS_REQ_FM_STATUS Format: Failed in mts_register of MTS_OPC_FM_SRV_FEATURE_STATUSExplanation Failed to request feature status notification.
Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-MTSBIND Format: Unable to bind to MTS SAP for %s, sap %d: %sExplanation EIGRP was not able to create a message queue for communication.
Parameters: Queue name, MTS SAP, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message EIGRP-2-NO_MEMORY Format: Can't allocate memory in function %sExplanation Cannot allocate memory in specified function.
Parameters: Function ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-NO_SET_PRIORITY Format: Failed to set policy or priorityExplanation EIGRP process could not set itself process priority, exiting.
Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-PROCINFO_CREATE_FAIL Format: eigrp_procinfo creation failedExplanation Failed to create procinfo.
Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-PTHREAD_FAILED Format: %s failed in %s for thread %sExplanation EIGRP process failed to create a task thread.
Parameters: Pthread operation, Function, Thread name ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-REG_L3VM Format: Failed to register with l3vmExplanation Failed to register with the l3vm process.
Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-REG_OPCODE Format: Could not register opcode 0x%x, reason %sExplanation Could not register mts opcode with the reason.
Parameters: Opcode, Reason ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-RLIMIT_FAILED Format: Couldn't set data segment size to %luExplanation EIGRP process could not set its memory resource limit, exiting.
Parameters: Data segment size ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-SBCR_INIT Format: Could not initialize shared database client, rc=0x%x [%s]Explanation Failed to initialize shared database client with return error code.
Parameters: Error code, Error string ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-TIMER_CREATE_FAIL Format: Failed to create %s active timerExplanation Failed to create specified active timer.
Parameters: Active timer name ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-TIMER_SET_INIT Format: Couldn't init %s active timer setExplanation EIGRP failed to initialize timer resource.
Parameters: Timer set name ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-URIB_ADD_ROUTE Format: urib_add_route() failedExplanation Failed to add routes to URIB.
Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-URIB_DEL_ROUTE Format: urib_delete_route() failedExplanation Failed to delete routes from URIB.
Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-URIB_DEREGISTER Format: Could not deregister with the URIB in %sExplanation EIGRP could not deregister with URIB in specified function.
Parameters: Function ...Recommended Action Restart the component when the system is working.
Error Message EIGRP-2-URIB_REDIST_LIMIT_WARNING Format: Redistribute threshold limit reached: %d%%.Explanation EIGRP has reached the configured redistRIBute maximum-prefix threshold.
Parameters: Threshold ...Recommended Action EIGRP process still operational. Send error log message and running configuration to the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message EIGRP-2-URIB_REGISTER Format: EIGRP could not register with the URIBExplanation At initialization time, EIGRP could not register with the URIB process.
Recommended Action Restart the component when the sys