Feedback
Table Of Contents
show configuration session global-info
show diagnostic content module
show diagnostic description module
show diagnostic ondemand setting
show event manager environment
show event manager event-types
show event manager history events
show event manager policy-state
show event manager system-policy
show hardware feature-capability
show hardware capacity interface
show hardware capacity fabric-utilization
show hardware flow utilization
show lldp dcbx interface ethernet
show lldp traffic interface ethernet
show logging ip access-list cache
show ntp authentication-status
show platform hardware capacity interface resources
show ptp clocks foreign-masters-record
show running-config diagnostic
show startup-config diagnostic
show system pss shrink status details
show system standby manual-boot
show Commands
This chapter describes the Cisco NX-OS system management show commands.
show callhome
To display information about the Call home application, use the show callhome command.
show callhome {destination-profile [profile profile_name] | last action status | last merge status | merge status | pending | pending-diff | session status | status | transport-email | user-def-cmds}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the status of the last CFS operation for the Call home application:
switch# show callhome last action statusLast Action Time Stamp : NoneLast Action : NoneLast Action Result : NoneLast Action Failure Reason : noneThis example shows how to display the Call home destination profile named Noc101:
switch# show callhome destination-profile profile Noc101Noc101 destination profile informationmaximum message size:2500000message format:XMLmessage-level:0email addresses configured:alert groups configured:allThis example shows how to display the Call home configuration:
switch# show callhomecallhome enabledCallhome Information:contact person name(sysContact):who@wherecontact person's email:someone@noc.comcontact person's phone number:+1-408-555-9918street addr:425 E Street, Anytown, CA 95999site id:8customer id:987654contract id:456789switch priority:7duplicate message throttling : enabledperiodic inventory : enabledperiodic inventory time-period : 7 daysperiodic inventory timeofday : 08:00 (HH:MM)Distribution : EnabledRelated Commands
show callhome transport
To display the transport-related configuration for Call home, use the show callhome transport command.
show callhome transport
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the transport-related configuration for Call home:
switch(config)# show callhome transporthttp vrf:defaultfrom email addr:person@company.comreply to email addr:person@company.comsmtp server:10.1.1.174smtp server port:25smtp server vrf:smtp server priority:0smtp server:64.72.101.213smtp server port:25smtp server vrf:defaultsmtp server priority:60smtp server:172.21.34.193smtp server port:25smtp server vrf:defaultsmtp server priority:50smtp server:192.0.2.1smtp server port:33smtp server vrf:Neosmtp server priority:1smtp server:192.0.2.10smtp server port:25smtp server vrf:defaultsmtp server priority:4switch(config)#Related Commands
show cdp
To display the interfaces that have Cisco Discovery Protocol (CDP) enabled, use the show cdp command.
show cdp {all | entry {all | name name} | global | interface interface-type | traffic interface interface-type}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the interfaces that have CDP enabled:
switch(config)# show cdp allmgmt0 is upCDP enabled on interfaceRefresh time is 60 secondsHold time is 30 secondsEthernet7/1 is downCDP enabled on interfaceRefresh time is 60 secondsHold time is 30 secondsEthernet7/2 is downCDP enabled on interfaceRefresh time is 60 secondsHold time is 30 secondsEthernet7/3 is downCDP enabled on interfaceRefresh time is 60 secondsHold time is 30 secondsEthernet7/4 is downCDP enabled on interfaceRefresh time is 60 secondsHold time is 30 secondsEthernet7/5 is downCDP enabled on interfaceRefresh time is 60 seconds--More--Related Commands
show cdp neighbors
To display the status of Cisco Discovery Protocol (CDP) neighbors, use the show cdp neighbors command.
show cdp neighbors [interface interface]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the status of CDP neighbors:
switch(config)# show cdp neighborsCapability Codes: R - Router, T - Trans-Bridge, B - Source-Route-BridgeS - Switch, H - Host, I - IGMP, r - Repeater,V - VoIP-Phone, D - Remotely-Managed-Device,s - Supports-STP-DisputeDevice-ID Local Intrfce Hldtme Capability Platform Port IDSwitch mgmt0 163 S I WS-C2960-24TC Fas0/21switch(config)#Related Commands
cdp holdtime
Configures the time that CDP holds onto neighbor information before refreshing it.
show cfs application
To display information about applications that are currently enabled to use Cisco Fabric Services (CFS) distribution, use the show cfs application command.
show cfs application [name application_name]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display CFS information about applications that are currently enabled to use CFS distribution:
switch# show cfs application----------------------------------------------Application Enabled Scope----------------------------------------------ntp No Physical-fc-ipstp Yes Physical-ethvpc Yes Physical-ethigmp Yes Physical-ethl2fm Yes Physical-ethrole No Physical-fc-ipradius No Physical-fc-ipcallhome Yes Physical-fc-ipTotal number of entries = 8This example shows how to display CFS information about the Call home application:
switch# show cfs application name callhomeEnabled : YesTimeout : 20sMerge Capable : YesScope : Physical-fc-ipRegion : 4Related Commands
show cfs lock
To display information about locks that are currently in place for an application that uses Cisco Fabric Services (CFS) for distribution, use the show cfs lock command.
show cfs lock [name application_name]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a lock that is currently in place for the Call home application that uses CFS for distribution:
switch(config-callhome)# show cfs lock name callhomeScope : Physical-fc-ip--------------------------------------------------------------------------------Switch WWN IP Address User Name User Type--------------------------------------------------------------------------------20:00:00:22:55:79:a4:c1 172.28.230.85 admin CLI/SNMP v3switchTotal number of entries = 10Related Commands
show cfs merge status
To display the merge status for an application that uses Cisco Fabric Services (CFS) for distribution, use the show cfs merge status command.
show cfs merge status [name application_name]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the current merge status for the Call home application that uses CFS for distribution. In this example, the most recent merge for the Call home application was successful.
switch(config-callhome)# show cfs merge status name callhomePhysical-fc-ip Merge Status: Success [ Wed Dec 17 16:34:26 2008 ]Local Fabric--------------------------------------------------------------------------------Switch WWN IP Address--------------------------------------------------------------------------------20:00:00:22:55:79:a4:c1 172.28.230.85 [Merge Master]switchTotal number of switches = 10Related Commands
show cfs peers
To display all peers in the physical fabric, use the show cfs peers command.
show cfs peers [name application_name]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display all peers in the physical fabric for the Call home application:
switch(config-callhome)# show cfs peers name callhomeScope : Physical-fc-ip-------------------------------------------------------------------------Switch WWN IP Address-------------------------------------------------------------------------20:00:00:22:55:79:a4:c1 172.28.230.85 [Local]switchTotal number of entries = 1Related Commands
show cfs regions
To display all Cisco Fabric Services (CFS) applications with peers and region information, use the show cfs regions command.
show cfs regions {name application_name | region region_id}
show cfs regions brief {name application_name | region region_id}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a brief version of all CFS regions:
switch# show cfs regions brief---------------------------------------Region Application Enabled---------------------------------------3 radius yes4 callhome yesThis example shows how to display a specified CFS region:
switch# show cfs regions region 4Region-ID : 4Application: callhomeScope : Physical-fc-ip-------------------------------------------------------------------------Switch WWN IP Address-------------------------------------------------------------------------20:00:00:22:55:79:a4:c1 172.28.230.85 [Local]switchTotal number of entries = 1Related Commands
show cfs status
To display the current state of Cisco Fabric Services (CFS), use the show cfs status command.
show cfs status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the current state of CFS:
switch# show cfs statusDistribution : EnabledDistribution over IP : Enabled - mode IPv4IPv4 multicast address : 239.255.70.83IPv6 multicast address : ff15::efff:4653Distribution over Ethernet : DisabledTotal number of entries = 8Related Commands
show checkpoint
To display the contents of the checkpoint file, use the show checkpoint command.
show checkpoint [name]
Syntax Description
name
(Optional) Name of the checkpoint file. The name can be any alphanumeric string up to 63 characters.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-operator
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the contents of the checkpoint file:
switch# show checkpoint stable
--------------------------------------------------------
Name: stableversion 4.0(2)power redundancy-mode combined forcelicense grace-periodfeature vrrpfeature tacacs+feature ospffeature pimfeature pim6feature msdpfeature eigrpfeature ripfeature isisfeature pbrfeature private-vlanfeature port-security
feature interface-vlanfeature dot1xfeature hsrpfeature lacpfeature glbp
feature dhcpfeature ctslogging level port-security 5logging level glbp 6snmp-server context foosnmp-server community <removed> group vdc-operatorsnmp-server community <removed> group network-adminsnmp-server community <removed> group vdc-adminrole feature-group name Xrole feature-group name xrole name xvlan policy denyvrf policy denypermit vrf xpermit vrf Xrole name Xusername adminbackup password 5 $1$Oip/C5Ci$oOdx7oJSlBCFpNRmQK4na. role vdc-operatorusername adminbackup role network-operatorusername admin password 5 $1$8GYeC4uW$4WfnImcvtAKI6Uet.ePD.1 role network-adminRelated Commands
show configuration session
To show information about the configuration sessions, use the show configuration session command.
show configuration session [name] [status] [summary]
Syntax Description
Defaults
Display information for all sessions
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about a configuration session. Each line represents a CLI command that Cisco NX-OS applies to the device when you commit the session.
switch# show configuration session myACLsconfig session name myACLs0001 ip access-list test10002 permit tcp any any0003 statisticsThis example shows how to display the status of a configuration session:
switch(config-s)# show configuration session statusSession Name : myACLSLast Action : NoneLast Action Status : SuccessLast Action Reason : -NA-Last Action Timestamp : 00:00:00 UTC Jan 01 1970This example shows how to display a summary of the configuration sessions:
switch(config-s)# show configuration session summaryName Session Owner Creation Time--------------------------------------------------------------------myACLS admin 21:34:39 UTC Apr 27 2008status admin 00:53:23 UTC Apr 29 2008a admin 01:47:30 UTC Apr 28 2008myACLs admin 00:56:46 UTC Apr 29 2008Number of active configuration sessions = 4switch(config-s)#Related Commands
show tech-support session-mgr
Shows detailed information about the configuration sessions for troubleshooting purposes.
show configuration session global-info
To display information about the global configuration session, use the show configuration session global-info command.
show configuration session global-info
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the global configuration session:
switch(config)# show configuration session global-infoMaximum number of sessions allowed : 32Maximum number of commands (all ssns) : 102400Current number of active sessions : 0Current number of commands (all ssns) : 0switch(config)#Related Commands
show cores
To display the system core files from the virtual device contexts (VDCs), use the show cores command.
show cores [vdc-all | {vdc [e-vdc2 | vdc-id]}]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the system core files:
switch(config)# show cores vdc-allVDC No Module-num Instance-num Process-name PID Core-create-time------ ---------- ------------ ------------ --- ----------------1 10 1 xmlsa 32442 May 8 15:241 10 1 xmlsa 25163 May 9 06:041 10 1 xmlsa 21581 May 9 13:25switch(config)#Related Commands
show diagnostic bootup level
To display information about bootup diagnostics, use the show diagnostic bootup level command.
show diagnostic bootup level
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the bootup diagnostic level:
switch# show diagnostic bootup levelCurrent bootup diagnostic level: completeswitch#
Related Commands
show diagnostic content module
To display information about the diagnostic test content for a module, use the show diagnostic content module command.
show diagnostic content module {all | module_number}
Syntax Description
module_number
Diagnostic content module number. The range is from 1 to 10.
all
Displays diagnostic content for all modules.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
Use the show diagnostic content module command to display information about the tests configured on the module and the repeat interval time.
Examples
This example shows how to display information about the diagnostic test content for a module:
switch# show diagnostic content module 6Module 6: Supervisor module-1X (Active)Diagnostics test suite attributes:B/C/* - Bypass bootup level test / Complete bootup level test / NAP/* - Per port test / NAS/* - Only applicable to standby unit / NAD/N/* - Disruptive test / Non-disruptive test / NAH/* - Always enabled monitoring test / NAF/* - Fixed monitoring interval test / NAX/* - Not a health monitoring test / NAE/* - Sup to line card test / NAL/* - Exclusively run this test / NAT/* - Not an ondemand test / NAA/I/* - Monitoring is active / Monitoring is inactive / NATesting IntervalID Name Attributes (hh:mm:ss)____ __________________________________ ____________ _________________1) ManagementPortLoopback--------> C**D**X**T* -NA-2) EOBCPortLoopback--------------> C**D**X**T* -NA-3) ASICRegisterCheck-------------> ***N******A 00:00:204) USB---------------------------> C**N**X**T* -NA-5) CryptoDevice------------------> C**N**X**T* -NA-6) NVRAM-------------------------> ***N******A 00:00:307) RealTimeClock-----------------> ***N******A 00:05:008) PrimaryBootROM----------------> ***N******A 00:30:009) SecondaryBootROM--------------> ***N******A 00:30:0010) CompactFlash------------------> ***N******A 00:30:0011) ExternalCompactFlash----------> ***N******A 00:30:0012) PwrMgmtBus--------------------> ***N******A 00:00:3013) SpineControlBus---------------> ***N******A 00:00:3014) SystemMgmtBus-----------------> ***N******A 00:00:30switchRelated Commands
show diagnostic description module
To display information about a diagnostic test for a module, use the show diagnostic description nodule command.
show diagnostic description module slot test {test-ID | test-name | all}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a diagnostic description for a module:
switch# show diagnostic description module 6 test 1ManagementPortLoopback :A bootup test that tests loopback on the management port ofthe moduleRelated Commands
show diagnostic events
To display information about diagnostic events, use the show diagnostic events command.
show diagnostic events [error | info]
Syntax Description
error
(Optional) Displays diagnostics by error type.
info
(Optional) Displays diagnostics by information type.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display diagnostic events:
switch# show diagnostic events1) Event:E_DEBUG, length:114, at 404616 usecs after Wed Jan 7 09:38:46 2009[104] Event_INFO: TestName->ASICRegisterCheck TestingType->helth monitoring module->9 Result->pass Reason->Success2) Event:E_DEBUG, length:114, at 414835 usecs after Wed Jan 7 09:38:26 2009[104] Event_INFO: TestName->ASICRegisterCheck TestingType->helth monitoring module->9 Result->pass Reason->Success3) Event:E_DEBUG, length:107, at 294482 usecs after Wed Jan 7 09:38:23 2009[104] Event_INFO: TestName->PwrMgmtBus TestingType->helth monitoring module->9 Result->pass Reason->SuccessThis example shows how to display diagnostic events by information type:
switch# show diagnostic events info1) Event:E_DEBUG, length:114, at 934712 usecs after Wed Jan 7 11:40:06 2009[104] Event_INFO: TestName->ASICRegisterCheck TestingType->helth monitoring module->9 Result->pass Reason->Success2) Event:E_DEBUG, length:110, at 314512 usecs after Wed Jan 7 11:39:53 2009[104] Event_INFO: TestName->SystemMgmtBus TestingType->helth monitoring module->9 Result->pass Reason->SuccessThis example shows how to display diagnostic events by event type:
switch# show diagnostic events errorswitch#Related Commands
show diagnostic ondemand setting
To display information about the on-demand diagnostic test for a module, use the show diagnostic ondemand setting command.
show diagnostic ondemand setting
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display diagnostic on-demand information:
switch# show diagnostic ondemand settingTest iterations = 1Action on test failure = continue until test failure limit reaches 1Related Commands
show diagnostic result
To display diagnostic test results for a module, use the show diagnostic result command.
show diagnostic result module {slot [test [test-id | test-name]] | all} [detail]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a diagnostic test result:
switch# show diagnostic result module 6 test 6 detailCurrent bootup diagnostic level: completeModule 6: Supervisor module-1X (Active)Diagnostic level at card bootup: completeTest results: (. = Pass, F = Fail, I = Incomplete,U = Untested, A = Abort, E = Error disabled)______________________________________________________________________6) NVRAM-------------------------> .Error code ------------------> DIAG TEST SUCCESSTotal run count -------------> 1574Last test execution time ----> Thu Jun 26 09:28:40 2008First test failure time -----> n/aLast test failure time ------> n/aLast test pass time ---------> Thu Jun 26 09:28:41 2008Total failure count ---------> 0Consecutive failure count ---> 0Last failure reason ---------> No failures yetswitch#show diagnostic simulation
To display information about a simulated diagnostic for a module, use the show diagnostic simulation command.
show diagnostic simulation module slot
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about simulated diagnostics:
switch# show diagnostic simulation module 6Card(6): Supervisor module-1X________________________________________________-NA-switch#Related Commands
show diagnostic status
To display the test status for all tests, use the show diagnostic status command.
show diagnostic status module slot
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the test status for all tests on a module:
switch# show diagnostic status module 6<BU>-Bootup Diagnostics, <HM>-Health Monitoring Diagnostics<OD>-OnDemand Diagnostics, <SCH>-Scheduled Diagnostics==============================================Card:(6) Supervisor module-1X==============================================Current running test Run by-NA- -NA-Currently Enqueued Test Run by-NA- -NA-switch#show diff rollback-patch
To display the differences between the source and destination, use the show diff rollback-patch command.
show diff rollback-patch {checkpoint name | running-config | startup-config}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the differences between the stable checkpoint file and the running configuration:
switch# show diff rollback-patch checkpoint stable running-configswitch#Related Commands
show checkpoint
Displays the contents of the checkpoint file.
rollback running checkpoint
Implements a rollback for the configured checkpoint file.
show environment
To display information about the hardware environment status, use the show environment command.
show environment [clock | fan | power | temperature]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
You can use this command to display information about the status of the hardware on your device.
This command does not require a license.
Examples
This example shows how to display information about the hardware environment:
switch# show environmentClock:----------------------------------------------------------Clock Model Hw Status----------------------------------------------------------A Clock Module -- NotSupported/NoneB Clock Module -- NotSupported/NoneFan:------------------------------------------------------Fan Model Hw Status------------------------------------------------------Fan1(sys_fan1) 0.0 OkFan2(sys_fan2) 0.0 OkFan3(fab_fan1) 0.0 OkFan4(fab_fan2) 0.0 OkFan_in_PS1 -- -- OkFan_in_PS2 -- -- OkFan_in_PS3 -- -- AbsentFan Air Filter : AbsentTemperature:--------------------------------------------------------------------Module Sensor MajorThresh MinorThres CurTemp Status(Celsius) (Celsius) (Celsius)--------------------------------------------------------------------2 Crossbar(s5) 105 95 40 Ok2 CTSdev1 (s6) 115 105 47 Ok2 CTSdev2 (s7) 115 105 51 Ok2 CTSdev3 (s8) 115 105 47 Ok2 CTSdev4 (s9) 115 105 48 Ok2 CTSdev5 (s10) 115 105 47 Ok2 CTSdev7 (s12) 115 105 50 Ok2 CTSdev8 (s13) 115 105 50 Ok2 CTSdev9 (s14) 115 105 48 Ok2 CTSdev10(s15) 115 105 48 Ok2 CTSdev11(s16) 115 105 46 Ok2 CTSdev12(s17) 115 105 45 Ok2 QEng1Sn1(s18) 115 105 43 Ok2 QEng1Sn2(s19) 115 105 42 Ok2 QEng1Sn3(s20) 115 105 39 Ok2 QEng1Sn4(s21) 115 105 40 Ok2 L2Lookup(s22) 115 105 43 Ok2 L3Lookup(s23) 120 110 54 OkPower Supply:Voltage: 50 Volts-----------------------------------------------------PS Model Power Power Status(Watts) (Amp)-----------------------------------------------------1 N7K-AC-6.0KW 0.00 0.00 Ok2 N7K-AC-6.0KW 6000.00 120.00 Ok3 ------------ 0.00 0.00 AbsentMod Model Power Power Power Power StatusRequested Requested Allocated Allocated(Watts) (Amp) (Watts) (Amp)--- ------------------- ------- ---------- --------- ---------- ----------2 N7K-M148GT-11 247.00 4.94 247.00 4.94 Powered-Up6 N7K-SUP1 210.00 4.20 210.00 4.20 Powered-UpXb1 N7K-C7010-FAB-1 123.50 2.47 123.50 2.47 Powered-UpPower Usage Summary:--------------------Power Supply redundancy mode: Non-Redundant(combined)Power Supply redundancy operational mode: Non-Redundant(combined)Total Power Capacity 6000.00 WPower reserved for Supervisor(s) 420.00 WPower reserved for Fan Module(s) 2184.00 WPower reserved for Fabric Module(s) 300.00 WPower currently used by Modules 247.00 W-------------Total Power Available 2849.00 W-------------This example shows how to display information about the power environment:
switch# show environment powerPower Supply:Voltage: 50 Volts-----------------------------------------------------PS Model Power Power Status(Watts) (Amp)-----------------------------------------------------1 FIORANO 0.00 0.00 Ok2 FIORANO 6000.00 120.00 Ok3 ------------ 0.00 0.00 AbsentMod Model Power Power Power Power StatusRequested Requested Allocated Allocated(Watts) (Amp) (Watts) (Amp)--- ------------------- ------- ---------- --------- ---------- ----------2 NURBURGRING 247.00 4.94 247.00 4.94 Powered-Up6 CATALUNYA 210.00 4.20 210.00 4.20 Powered-UpXb1 Estoril 123.50 2.47 123.50 2.47 Powered-UpPower Usage Summary:--------------------Power Supply redundancy mode: Non-Redundant(combined)Power Supply redundancy operational mode: Non-Redundant(combined)Total Power Capacity 6000.00 WPower reserved for Supervisor(s) 420.00 WPower reserved for Fan Module(s) 2184.00 WPower reserved for Fabric Module(s) 300.00 WPower currently used by Modules 247.00 W-------------Total Power Available 2849.00 W-------------Related Commands
show environment power
To display information about the power capacity and power distribution of the system, use the show environment power command.
show environment power [ampere | detail]
Syntax Description
ampere
(Optional) Displays information about the power capacity and power distribution in amperes.
detail
(Optional) Displays detailed information about the power capacity and power distribution.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
By reading information from the power supply, the system displays the power consumption information.
The actual power consumed by the system might be more than what is displayed.
This command does not require a license.
Examples
This example shows how to display information about the power capacity and power distribution of the system:
switch(config) show environment power amperePower Supply:Voltage: 50 VoltsPower Actual TotalSupply Model Output Capacity Status(Ampere) (Ampere)------- ------------------- ----------- ----------- --------------1 N7K-AC-6.0KW 29.40 A 120.00 A Ok2 N7K-AC-6.0KW 0.00 A 0.00 A Ok3 ------------ 0.00 A 0.00 A Absent4 ------------ 0.00 A 0.00 A AbsentActual PowerModule Model Draw Allocated Status(Ampere) (Ampere)------- ------------------- ----------- ----------- --------------6 N7K-M108X2-12L 371.00 A 17.00 A Powered-Up7 N7K-M148GS-11 254.00 A 9.00 A Powered-Up8 N7K-M148GS-11L 247.00 A 8.00 A Powered-Up9 supervisor N/A 4.20 A Absent10 N7K-SUP1 N/A 4.20 A Powered-UpXb1 N7K-C7018-FAB-1 N/A 2.00 A Powered-UpXb2 xbar N/A 2.00 A AbsentXb3 xbar N/A 2.00 A AbsentXb4 xbar N/A 2.00 A AbsentXb5 xbar N/A 2.00 A Absentfan1 N7K-C7018-FAN 4.34 A 14.72 A Powered-Upfan2 N7K-C7018-FAN 3.78 A 10.74 A Powered-UpN/A - Per module power not availablePower Usage Summary:--------------------Power Supply redundancy mode (configured) Non-Redundant(combined)Power Supply redundancy mode (operational) Non-Redundant(combined)Total Power Capacity (based on configured mode) 120.00 ATotal Power of all Inputs (cumulative) 120.00 ATotal Power Output (actual draw) 29.40 ATotal Power Allocated (budget) 77.00 ATotal Power Available for additional modules 42.14 Aswitch(config)#Related Commands
show event manager environment
To display the name and value of Embedded Event Manager (EEM) environment variables, use the show event manager environment command.
show event manager environment {varname | all}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display all of the EEM environment variables:
switch# show event manager environment allswitch#show event manager event-types
To display the Embedded Event Manager (EEM) event types, use the show event manager event-types command.
show event manager event-types [detail | event-type-name] [module module]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the details of the EEM event types:
switch# show event manager event-types detailswitch#show event manager history events
To display the Embedded Event Manager (EEM) events that have been triggered, use the show event manager history events command.
show event manager history events [detail] [maximum number] [severity severity]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the EEM history events that have been triggered that were of severity 7:
switch# show event manager history events severity 7switch#show event manager policy
To display the registered Embedded Event Manager (EEM) policies, use the show event manager policy command.
show event manager policy [detail] [policy-name | inactive]
Syntax Description
detail
(Optional) Displays details of all policies.
policy-name
(Optional) Name of the policy.
inactive
(Optional) Displays only those policies that are inactive.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the EEM policies:
switch# show event manager policyswitch#show event manager policy-state
To display the state of the named Embedded Event Manager (EEM) policy, use the show event manager policy-state command.
show event manager policy-state name [module module]
Syntax Description
name
Name of a policy to display its state.
module module
(Optional) Displays the policy state defined for a specific module. The range is from 1 to 10.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the state of an EEM policy:
switch# show event manager policy-state policy42switch#show event manager script
To display the script policy of the Embedded Event Manager (EEM), use the show event manager script command.
show event manager script system {name | all}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display all the system scripts defined in the EEM:
switch# show event manager script system allswitch#show event manager system-policy
To display the system policies of the Embedded Event Manager (EEM), use the show event manager system-policy command.
show event manager system-policy [all]
Syntax Description
all
(Optional) Displays all policies (including advanced policies and those policies that cannot be overridden).
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the EEM system policies:
switch# show event manager system-policyName : __BootupPortLoopbackDescription : Do CallHome, log error on affected ports after 1 consecutive failure of GOLD "BootupPortLoopback" testOverridable : YesName : __PortLoopbackDescription : Do CallHome, log error and disable further HM testing on affected ports after 10 consecutive failures of GOLD "PortLoopback" testOverridable : YesName : __RewriteEngineLoopbackDescription : Do CallHome, log error and disable further HM testing on affected ports after 10 consecutive failures of GOLD "RewriteEngineLoopback" testOverridable : YesName : __asic_register_checkDescription : Do CallHome, log error and disable further HM testing for thatASIC device/instance after 20 consecutive failures of GOLD "AsicRegisterCheck"testOverridable : YesName : __compact_flashDescription : Do CallHome, log error and disable further HM testing after 20consecutive failures of GOLD "CompactFlash" testOverridable : YesName : __crypto_deviceDescription : Do CallHome and log error when GOLD "CryptoDevice" test failsOverridable : YesName : __eobc_port_loopbackDescription : Do CallHome and log error when GOLD "EOBCPortLoopback" test failsOverridable : YesName : __ethpm_debug_1Description : Action: noneOverridable : YesName : __ethpm_debug_2Description : Action: noneOverridable : YesName : __ethpm_debug_3Description : Action: noneOverridable : YesName : __ethpm_debug_4Description : Action: noneOverridable : YesName : __ethpm_link_flapDescription : More than 30 link flaps in 420 seconds interval. Action: ErrorDisable the portOverridable : YesName : __external_compact_flashDescription : Do CallHome, log error and disable further HM testing after 20consecutive failures of GOLD "ExternalCompactFlash" testOverridable : Yesswitch#show flow exporter
To display the Flexible NetFlow flow exporter status and statistics, use the show flow exporter command.
show flow exporter [name exporter-name]
Syntax Description
name exporter-name
(Optional) Specifies the name of a flow exporter. The name can be any case-sensitive, alphanumeric string up to 64 characters.
Defaults
Information for all flow exporters configured on the router is displayed.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
This command does not require a license.
Examples
This example shows how to display the status and statistics for all of the flow exporters configured on the router:
switch# show flow exporterFlow Exporter NFC-DC-PHOENIX:Export Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverFlow exporter timeout:Export Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverFlow exporter test-exporter:Description: test server in San Jose CAExport Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverRelated Commands
show flow interface
To display the Flexible NetFlow configuration and status for an interface, use the show flow interface command.
show flow interface [interface-type number]
Syntax Description
interface-type number
(Optional) Type of interface that you want to view Flexible NetFlow accounting configuration information on.
Defaults
Information for the Flexible NetFlow accounting configuration on the interface is displayed.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show flow interface command.
This command does not require a license.
Examples
This example shows how to display the Flexible NetFlow accounting configuration on interface Ethernet 0/0 and 0/1:
switch# show flow interface ethernet 1/0Interface Ethernet1/0FNF: monitor: NFC-DC-PHOENIXdirection: Outputtraffic(ip): onswitch# show flow interface ethernet 0/0Interface Ethernet0/0FNF: monitor: FLOW-MONITOR-1direction: Inputtraffic(ip): sampler SAMPLER-2#Table 1 describes the significant fields shown in the display.
Related Commands
show flow monitor
To display the status and statistics for a Flexible NetFlow flow monitor, use the show flow monitor command.
show flow monitor [name exporter-name]
Syntax Description
name exporter-name
(Optional) Specifies the name of a flow exporter. The name can be any case-sensitive, alphanumeric string up to 64 characters.
Defaults
Information for all flow exporters configured on the router is displayed.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
This command does not require a license.
Examples
This example shows how to display the status and statistics for a flow monitor:
switch# show flow monitor NFC-DC-PHOENIX statisticsCache type: NormalCache size: 4096Current entries: 4High Watermark: 6Flows added: 116Flows aged: 112- Active timeout ( 1800 secs) 0- Inactive timeout ( 15 secs) 112- Event aged 0- Watermark aged 0- Emergency aged 0Table 2 describes the significant fields shown in the display.
This example shows how to display the status for a flow monitor:
switch# show flow monitor NFC-DC-PHOENIXFlow Monitor NFC-DC-PHOENIX:Description: Used for basic traffic analysisFlow Record: netflow-originalFlow Exporter: EXP-DC-TOPEKAEXP-DC-PHOENIXCache:Type: normalStatus: allocatedSize: 4096 entries / 311316 bytesInactive Timeout: 15 secsActive Timeout: 1800 secsUpdate Timeout: 1800 secsTable 3 describes the significant fields shown in the display.
This example shows how to display the status and statistics for the flow monitor named NFC-DC-PHOENIX:
switch# show flow monitor NFC-DC-PHOENIX cacheCache type: NormalCache size: 4096Current entries: 8High Watermark: 10Flows added: 1560Flows aged: 1552- Active timeout ( 1800 secs) 24- Inactive timeout ( 15 secs) 1528- Event aged 0- Watermark aged 0- Emergency aged 0IP TOS: 0x00IP PROTOCOL: 6IPV4 SOURCE ADDRESS: 10.10.10.2IPV4 DESTINATION ADDRESS: 172.16.10.2TRNS SOURCE PORT: 20TRNS DESTINATION PORT: 20INTERFACE INPUT: Et0/0FLOW SAMPLER ID: 0ip source as: 0ip destination as: 0ipv4 next hop address: 172.16.7.2ipv4 source mask: /0ipv4 destination mask: /24tcp flags: 0x00interface output: Et1/0counter bytes: 198520counter packets: 4963timestamp first: 10564356timestamp last: 12154104Table 4 describes the significant fields shown in the display.
This example shows how to display the status and statistics for the flow monitor named NFC-DC-PHOENIX in a table format:
switch# show flow monitor NFC-DC-PHOENIX cache format tableCache type: NormalCache size: 4096Current entries: 4High Watermark: 6Flows added: 90Flows aged: 86- Active timeout ( 1800 secs) 0- Inactive timeout ( 15 secs) 86- Event aged 0- Watermark aged 0- Emergency aged 0IP TOS IP PROT IPV4 SRC ADDR IPV4 DST ADDR TRNS SRC PORT TRNS DST PORT====== ======= =============== =============== ============= ==============0x00 1 10.251.10.1 172.16.10.2 0 020x00 1 10.251.10.1 172.16.10.2 0 204840xC0 17 172.16.6.1 224.0(1).0.9 520 52020x00 6 10.10.11.1 172.16.10.5 25 252switch#Related Commands
show flow record
To display the status and statistics of a Flexible NetFlow flow record, use the show flow record command.
show flow record [name record-name | netflow ipv4 record | netflow-original]
Syntax Description
name record-name
(Optional) Specifies the name of a flow record that you previously configured.
netflow ipv4 record
(Optional) Configures the flow monitor to use one of the predefined records. See Table 5 for a listing of the available records and their definitions.
netflow-original
(Optional) Specifies the Flexible NetFlow implementation of original NetFlow with origin autonomous systems.
Defaults
Information for all flow exporters configured on the router is displayed.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
Table 5 describes the keywords and descriptions for the record argument.
Table 5 Keywords and Descriptions for the record Argument
original-input
Traditional IPv4 input NetFlow.
original-output
Traditional IPv4 output NetFlow.
protocol-port
Protocol ports record.
This command does not require a license.
Examples
This example shows how to display the status and statistics of the original input NetFlow record:
switch# show flow record netflow ipv4 original-inputFlow record ipv4 original-input:Description: Traditional IPv4 input NetFlowNo. of users: 0Template ID: 0Fields:match ipv4 source addressmatch ipv4 destination addressmatch ip protocolmatch ip tosmatch transport source-portmatch transport destination-portmatch interface inputcollect routing source ascollect routing destination ascollect routing next-hop address ipv4collect transport tcp flagscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime lastcollect interface outputswitch#Table 6 describes the significant fields shown in the display.
Related Commands
show flow timeout
To display the Flexible NetFlow flow cache timeout values, use the show flow timeout command.
show flow timeout
Syntax Description
This command has no arguments or keywords.
Defaults
Information for the Flexible NetFlow accounting configuration on the interface is displayed.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show flow timeout command.
This command does not require a license.
Examples
This example shows how to display the Flexible NetFlow flow cache timeout values:
switch# show flow timeoutFlow timeout valuesActive timeout: 1800 secondsInactive timeout: 15 secondsFast timeout: DisabledSession aging timeout: DisabledAggressive aging timeout: Disabledswitch#Related Commands
show hardware feature-capability
To display information about the registered features that are supported by the system, use the show hardware feature-capability command.
show hardware feature-capability [detailed]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operator
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the registered features that are supported by the system:
switch# show hardware feature-capability detailedHardware Dependent Features:. = supportedX = unsupported-- Module --7 12VPC X Xmodule 7: Device Min num too small for featuremodule 12: Device Min num too small for featurePVLAN . .switch#Related Commands
show hardware capacity
Displays information about the hardware capabilities and current hardware utilization by the system.
show hardware capacity
To display information about the hardware capabilities and current hardware utilization by the system, use the show hardware capacity command.
show hardware capacity [eobc | fabric-utilization | forwarding | interface | module | power]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You can make network design plans based on the information about hardware capabilities and the current hardware utilization.
This command does not require a license.
Examples
This example shows how to display information about the hardware capabilities and current hardware utilization by the system:
switch(config)# show hardware capacity moduleSupervisor Redundancy HW Mode(Dual-SUPs): DisabledRedundancy mode: Active with no standbySwitching Resources:-------------------Module Model Number Part Number Serial Number---------------------------------------------------------7 N7K-M148GS-11 73-11584-02 JAF1219AGFE10 N7K-SUP1 73-10877-11 JAF1307ALAT12 NURBURGRING 73-10098-04 JAB104400P0XBAR Resources:-------------------XbarNum Model Number Part Number Serial Number---------------------------------------------------------1 N7K-C7018-FAB-1 73-11687-01 JAF1225AGHJFlash/NVRAM Resources:------------------------------------------------------------Usage: Module Device Total(KB) Free(KB) %Used------------------------------------------------------------10 bootflash 1762048 1383980 2110 logflash 7997912 6840772 1410 slot0 2026608 1985436 2switch(config)#Related Commands
show hardware fabric-utilization
Displays information about fabric utilizations.
show module
Displays information about a module.
show hardware capacity interface
To display information about the hardware interface resources, use the show hardware capacity interface command.
show hardware capacity interface
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the hardware interface resources:
switch(config)# show hardware capacity interfaceInterface ResourcesInterface drops:Module Total drops Highest drop ports7 Tx: 0 -7 Rx: 0 -12 Tx: 0 -12 Rx: 0 -Interface buffer sizes:Module Bytes: Tx buffer Rx buffer7 6190631 774333012 6190631 7743330switch#Related Commands
show hardware flow utilization
Displays information about NetFlow hardware flow utilization.
show hardware fabric-utilization
Displays information about fabric utilization.
show hardware capacity fabric-utilization
To display information about the current and peak switching fabric utilization, use the show hardware capacity fabric-utilization command.
show hardware capacity fabric-utilization
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the current and peak switching fabric utilization:
switch(config)# show hardware capacity fabric-utilization------------------------------------------------------------------Fabric Planes:A -- Unicast fabric interfaceB -- Multicast/Multidestination fabric interface-------------------------PEAK FABRIC UTILIZATION------------------I/O |-----FABRIC----|Slot |Mod Inst Plane| Dir Util Time------------------------------------------------------------------7 1 1 A ingress 0% Mon Aug 24 08:31:52 20097 1 1 B ingress 0% Mon Aug 24 08:31:52 20097 1 1 A egress 0% Mon Aug 24 08:31:52 20097 1 1 B egress 0% Mon Aug 24 08:31:52 20097 1 2 A ingress 0% Mon Aug 24 08:31:52 20097 1 2 B ingress 0% Mon Aug 24 08:31:52 20097 1 2 A egress 0% Mon Aug 24 08:31:52 20097 1 2 B egress 0% Mon Aug 24 08:31:52 200910 1 1 A ingress 0% Mon Aug 24 08:31:41 200910 1 1 B ingress 0% Mon Aug 24 08:31:41 200910 1 1 A egress 0% Mon Aug 24 08:31:41 200910 1 1 B egress 0% Mon Aug 24 08:31:41 2009--More--Related Commands
show hardware flow aging
To display information about NetFlow hardware flow aging, use the show hardware flow aging command.
show hardware flow aging [vdc vdc-name] [detail] [module slot-number]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow aging command.
This command does not require a license.
Examples
This example shows how to display the NetFlow aging values for module 2:
switch(config)# show hardware flow aging module 2VDC(1) Aging Information (time unit is second):AgingType Enabled Timeout Period Threshold----------+----------+----------+----------+----------Active Yes 1800 360 N/AInactive Yes 15 3 N/AFast Yes 33 6 22Aggressive No 90 18 90Session No 2 5 N/Aswitch(config)#Related Commands
show hardware flow entry
To display information about NetFlow table entry, use the show hardware flow entry command.
show hardware flow entry address location type {ip | ipv6} [detail] [module slot-number]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow entry command.
This command does not require a license.
Examples
This example show how to display the NetFlow table entry for module 2:
switch(config)# show hardware flow entry address 0x0 type ip module 2NT Entry Info (dev_id = 0, nt_entry_addr = 0x00000000):protocol = 0 (0=IPv4/IPMAC, 1=IPv6, 2=L2, 3=MPLS)profile_id = 0recir_id = 0is_routed = 0from_rp = 0lkup_dir = 0 (0=Ingress, 1=Egress)ilif(ovld_a) = 0x0elif(ovld_b) = 0x0tos(ovld_e) = 0l4_protocol = 0l4_hdr_vld = 0fragment = 0mpls = 0l4_info(ovld_d) = 0x00000000ipv4_sa(ovld_f) = 0.0.0.0ipv4_da(ovld_g) = 0.0.0.0ipmac = 0segment = 0hash_addr = 0x0icam = 0create_ts = 0sh_plc_idx/sampler_id = 0x0rdt_tbl_idx = 0x0ignr_aclo = 0ignr_qoso = 0ignr_acc = 0ignr_agg_qos = 0tcp_rdt_dst = 0copy_policy_idx = 0x0nf_acos = 0mark_en = 0nf_qos_mode = 0policer_param_idx = 0x0elam_trig = 0valid = 0sw_entry = 0profile_merged = 0fast_ag_en = 0sw_bits1 = 0dgt_mode = 0adj_ptr/dgt = 0x0ignr_qosi = 0ignr_acli = 0NS Entry Info (dev_id = 0, ns_entry_addr = 0x00000000):ack_after_fin = 0tcp_flag = 0x0 (URG=0, ACK=0, PSH=0, RST=0, SYN=0, FIN=0)mf_ls_ts = 0mf_bkt = 0nf_pkt_cnt = 0000000000nf_byte_cnt = 0000000000000nf_byte_cnt_excd = 0000000000000ls_used_ts = 0sw_prog/sticky_status = 0Related Commands
show hardware flow ip
To display information about NetFlow hardware IP flows, use the show hardware flow ip command.
show hardware flow ip [interface type number | monitor monitor-name | profile profile-id | vdc vdc-name | vlan vlan-name] [detail] [module module]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow ip command.
This command does not require a license.
Examples
This example shows how to display the NetFlow aging values for module 8:
switch(config)# show hardware flow ip module 8D - Direction; L4 Info - Protocol:Source Port:Destination PortIF - Interface: ()ethernet, (S)vi, (V)lan, (P)ortchannel, (T)unnelTCP Flags: Ack, Flush, Push, Reset, Syn, UrgentD IF SrcAddr DstAddr L4 Info PktCnt TCP Flags-+-----+---------------+---------------+---------------+----------+-----------I 8/26 007.002.000.002 007.001.000.002 000:00000:00000 0000421885 . . . . . .I 8/25 007.001.000.002 007.002.000.002 000:00000:00000 0000421900 . . . . . .O 8/25 007.002.000.002 007.001.000.002 000:00000:00000 0000422213 . . . . . .O 8/26 007.001.000.002 007.002.000.002 000:00000:00000 0000422228 . . . . . .switch(config)#Related Commands
show hardware flow sampler
To display information about sampled NetFlow hardware flows, use the show hardware flow sampler command.
show hardware flow sampler [all | count | index number | name sampler-name | vdc vdc_id] [detail] [module module]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow sampler command.
This command does not require a license.
Examples
This example shows how to display the NetFlow sampler table utilization for module 2:
switch# show hardware flow sampler count module 2Sampler Table Utilization: about 0.00% (0/64)Related Commands
show hardware flow utilization
To display information about NetFlow hardware flow utilization, use the show hardware flow utilization command.
show hardware flow utilization [module module]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow utilization command.
This command does not require a license.
Examples
This example shows how to display the NetFlow sampler table utilization for module 2:
switch# show hardware flow utilization module 2Flow Utilization: 0.00% (0/515090)Total number of flows = 0IPv4 flow creation failure = 0IPv6 flow creation failure = 0MPLS flow creation failure = 0L2 flow creation failure = 0IFE flow creation failure = 0OFE flow creation failure = 0IFE CF FIFO full failure = 0OFE CF FIFO full failure = 0IFE NT table full failure = 0OFE NT table full failure = 0NO freelist pointer failure = 0Hash Table(NH) page full failure = 0IPMAC lookup failure = 0L2 ACL deny = 0L3 ACL deny = 0IFE CF flow control = 0OFE CF flow control = 0Fast Aging failure = 0switch#Related Commands
show inventory
To display inventory information for the device hardware, use the show inventory command.
show inventory [chassis | clock | fans | module | power_supply]
Syntax Description
Defaults
Displays all hardware inventory information.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display configuration incompatibilities:
switch# show inventoryNAME: "Chassis", DESCR: "Nexus7000 C7010 (10 Slot) Chassis "PID: N7K-C7010 , VID: , SN: TBM11256507NAME: "Slot 2", DESCR: "10/100/1000 Mbps Ethernet Module"PID: N7K-M148GT-11 , VID: , SN: JAB104400P0NAME: "Slot 6", DESCR: "Supervisor module-1X"PID: N7K-SUP1 , VID: TBD , SN: JAB10380101NAME: "Slot 11", DESCR: "Fabric card module"PID: N7K-C7010-FAB-1 , VID: , SN: JAB104300HMNAME: "Slot 33", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Power Supply"PID: FIORANO , VID: , SN: DTH1117T005NAME: "Slot 34", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Power Supply"PID: N7K-AC-6.0KW , VID: , SN: DTH1117T009NAME: "Slot 36", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 37", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 38", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 39", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:switch#show lldp dcbx interface ethernet
To display the local Data Center Bridging Capability Exchange (DCBX) control status of an interface, use the show lldp dcbx interface ethernet command.
show lldp dcbx interface ethernet slot/port-number
Syntax Description
slot/port-number
Slot number and port number is this format: slot/port-number. The range is from 1 to 253.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the local DCBX control status:
switch(config)# show lldp dcbx interface ethernet 1/5Local DCBXP Control information:Operation version: 00 Max version: 00 Seq no: 1 Ack no: 1 Type/Subtype Version En/Will/Adv Config003/000 000 Y/N/Y 0008002/000 000 Y/N/Y 1111100032 32000000 00000002Peer's DCBXP Control information:Operation version: 00 Max version: 00 Seq no: 1 Ack no: 1Type/ Max/OperSubtype Version En/Will/Err Config003/000 000/000 Y/N/N 0008002/000 000/000 Y/N/N 1111100032 32000000 00000002switch(config)#Related Commands
show lldp tlv-select
Displays the LLDP TLV configuration.
lldp tlv-select
Specifies the TLVs to send and receive in LLDP packets.
show lldp interface ethernet
To display the Link Layer Discovery Protocol (LLDP) configuration on the interface, use the show lldp interface ethernet command.
show lldp interface ethernet slot/port-number
Syntax Description
slot/port-number
Slot number and port number in this format: slot/port-number. The range is from 1 to 253.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the LLDP configuration on the interface:
switch(config)# show lldp interface ethernet 6/3Interface Information:Enable (tx/rx/dcbx): Y/Y/Y Port Mac address: 00:24:f7:19:84:72switch(config)#Related Commands
show lldp neighbors
To display the status of the Link Layer Discovery Protocol (LLDP) neighbor device, use the show lldp neighbors command.
show lldp neighbors {detail | interface ethernet slot/port-number}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the LLDP neighbor device status:
switch(config)# show lldp neighbors detailCapability codes:(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device(W) WLAN Access Point, (P) Repeater, (S) Station, (O) OtherLocal Intf Chassis ID Port ID Hold-time CapabilityEth8/24 0018.bad8.5e45 Eth8/23 120 REth8/23 0018.bad8.5e45 Eth8/24 120 Rswitch(config)#Related Commands
show lldp timers
To display the Link Layer Discovery Protocol (LLDP) hold time, delay time, and update frequency configuration, use the show lldp timers command.
show lldp timers
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the LLDP hold time, delay time, and update frequency configuration:
switch(config)# show lldp timersLLDP Timers:Holdtime in seconds: 180Reinit-time in seconds: 6Transmit interval in seconds: 45switch(config)#Related Commands
show lldp tlv-select
To display the type, length, and value (TLV) configuration for the Link Layer Discovery Protocol (LLDP), use the show lldp tlv-select command.
show lldp tlv-select
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the TLV configuration for LLDP:
switch(config)# show lldp tlv-selectaccess-managementdcbxport-descriptionport-vlansystem-capabilitiessystem-descriptionsystem-nameswitch(config)#Related Commands
show lldp dcbx interface ethernet
Displays the local DCBX control status.
lldp tlv-select
Specifies the TLVs to send and receive in LLDP packets.
show lldp traffic
To display the Link Layer Discovery Protocol (LLDP) counters, including the number of LLDP packets sent and received by the device, the number of discarded packets, and the number of unrecognized TLVs, use the show lldp traffic command.
show lldp traffic
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the LLDP counters:
switch(config)# show lldp trafficLLDP traffic statistics:Total frames transmitted: 323Total entries aged: 0Total frames received: 0Total frames received in error: 0Total frames discarded: 0Total unrecognized TLVs: 0switch(config)#Related Commands
show lldp traffic interface ethernet
Displays the number of LLDP packets sent and received on the interface.
show running-config lldp
Displays the global LLDP configuration.
show lldp traffic interface ethernet
To display the number of Link Layer Discovery Protocol (LLDP) packets sent and received on the interface, use the show lldp traffic interface ethernet command.
show lldp traffic interface ethernet slot/port-number
Syntax Description
slot/port-number
Slot number and port number in this format: slot/port-number. The range is from 1 to 253.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the number of LLDP packets sent and received on the interface:
switch(config)# show lldp traffic interface ethernet 7/1LLDP interface traffic statistics:Total frames transmitted: 0Total entries aged: 0Total frames received: 0Total frames received in error: 0Total frames discarded: 0Total unrecognized TLVs: 0switch(config)#Related Commands
show locator-led status
To show the status of locator LEDs on the system, use the show locator-led status command.
show locator-led status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the locator LED status for the system:
switch# show locator-led statusXbar 1 : Locator LED offModule 7 : Locator LED offModule 9 : Locator LED offModule 12 is not powered up.Chassis Locator LED offPowerSupply 1 : Locator LED offPowerSupply 2 : Locator LED offFan 1 : Locator LED offFan 2 : Locator LED offswitch(config)#Related Commands
show logging console
To display the console logging configuration, use the show logging console command.
show logging console
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the console logging configuration:
switch# show logging console Logging console: enabled (Severity: critical)switch#Related Commands
show logging info
To display the logging configuration, use the show logging info command.
show logging info
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging configuration:
switch# show logging infoLogging console: enabled (Severity: critical)Logging monitor: enabled (Severity: notifications)Logging linecard: enabled (Severity: notifications)Logging timestamp: SecondsLogging loopback : disabledLogging server: enabled{172.28.254.254}server severity: notificationsserver facility: local7server VRF: defaultLogging logflash: enabled (Severity: information)Logging logfile: enabledName - messages: Severity - information Size - 10485760Facility Default Severity Current Session Severity-------- ---------------- ------------------------aaa 3 5acllog 2 2aclmgr 3 3auth 0 0authpriv 3 3bfd 2 2--More--show logging ip access-list cache
To display information about the logging IP access list cache, use the show logging ip access-list cache command.
show logging ip access-list cache
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the logging IP access list cache:
switch# show logging ip access-list cacheswitch#Related Commands
show logging last
To display the last number lines of the logfile, use the show logging last command.
show logging last number
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the last 42 lines of the logfile:
switch# show logging last 42switch#show logging level
To display a logging configuration, use the show logging level command.
show logging level [level]
Syntax Description
level
(Optional) Logging configuration to display. The keyword options are listed in the "System Message Logging Facilities" section on page 659.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
4.0(1)
This command was introduced.
4.0(2)
Added the interface-vlan, netstack, private-vlan, and ipv6 keywords.
4.1(2)
Added the cfs keyword.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the current Cisco Fabric Services (CFS) logging configuration:
switch# show logging level cfsFacility Default Severity Current Session Severity-------- ---------------- ------------------------cfs 3 30(emergencies) 1(alerts) 2(critical)3(errors) 4(warnings) 5(notifications)6(information) 7(debugging)Related Commands
show logging logfile
To display the messages in the log file that were timestamped within the span entered, use the show logging logfile command.
show logging logfile [start-time yyyy mmm dd hh:mm:ss] [end-time yyyy mmm dd hh:mm:ss]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
If you do not enter an end time, the current time is used.
This command does not require a license.
Examples
This example shows how to display the messages in the log file that were timestamped within the span shown:
switch# show logging logfile start-time 2008 mar 11 12:10:00switch#Related Commands
show logging loopback
To display the logging loopback configuration, use the show logging loopback command.
show logging loopback
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging loopback configuration:
switch# show logging loopbackswitch#show logging module
To display the module logging configuration, use the show logging module command.
show logging module
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the module logging configuration:
switch# show logging moduleswitch#Related Commands
show logging monitor
To display the monitor logging configuration, use the show logging monitor command.
show logging monitor
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the monitor logging configuration:
switch# show logging monitorswitch#Related Commands
show logging nvram
To display the messages in the NVRAM log, use the show logging nvram command.
show logging nvram [last number-lines]
Syntax Description
last number-lines
(Optional) Specifies a number of lines to display. The last number-lines is displayed. The range is from 1 to 100 lines.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the last 20 messages in the NVRAM log:
switch# show logging nvram last 20switch#show logging onboard
To display the onboard logging information based on the error type, use the show logging onboard command.
show logging onboard {boot-uptime | device-version | counter-stats | endtime | environmental-history | error-stats | exception-log | interrupt-stats | kernel-trace | module num | obfl-history | obfl-logs | stack-trace | starttime | status}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
The date and time arguments for the starttime and endtime keywords are entered as the date month/day/year (mm/dd/yy), followed by a hyphen, and the time in 24-hour format in hours:minutes:seconds (HH:MM:SS). For example:
•
starttime 03/17/08-15:01:57
•
The valid values for file are as follows:
•
•
•
•
•
•
•
The valid values for type are as follows:
•
–
–
–
•
•
–
–
–
–
–
–
–
–
–
•
–
–
–
•
•
–
–
–
•
•
–
–
•
•
•
–
–
–
–
–
Use this command to view OBFL data from the system hardware. The OBFL feature is enabled by default and records operating temperatures, hardware uptime, interrupts, and other important events and messages that can assist with diagnosing problems with hardware modules installed in a Cisco router or switch. Data is logged to files that are stored in nonvolatile memory. When the onboard hardware is started up, a first record is made for each area monitored and becomes a base value for subsequent records.
The OBFL feature provides a circular updating scheme for collecting continuous records and archiving older (historical) records, ensuring accurate data about the system. Data is recorded in one of two formats: continuous information that displays a snapshot of measurements and samples in a continuous file, and summary information that provides details about the data being collected. The message "No historical data to display" is seen when historical data is not available.
This command does not require a license.
Examples
This example shows how to display the OBFL boot and uptime information:
switch# show logging onboard module 2 boot-uptimeSat Feb 29 18:11:38 2008: Boot Record----------------------------------------------------------------Boot Time..........: Sat Feb 29 18:11:38 2008Slot Number........: 2Serial Number......: JAB0912026UBios Version.......: v0.0.8(08/18/07)Alt Bios Version...: v0.0.8(08/18/07)Firmware Version...: 3.0(1) [build 3.0(0.291)]switch#Table 7 describes the significant fields shown in the display.
This example shows how to display the OBFL logging device information:
switch# show logging onboard module 2 device-versionDevice Version Records:------------------------------------------------------------------------Timestamp Device Name Instance Hardware SoftwareNum Version Version------------------------------------------------------------------------Sat Feb 29 18:11:38 2008 Stratosphere 0 1 1Sat Feb 29 18:11:38 2008 Stratosphere 1 1 1Sat Feb 29 18:11:38 2008 Skyline-asic 0 1 1Sat Feb 29 18:11:38 2008 Tuscany-asic 0 1 0Sat Feb 29 18:11:38 2008 X-Bus IO 0 6 0Sat Feb 29 18:11:38 2008 Power Mngmnt Epl 0 6 0Sat Feb 29 18:42:01 2008 Stratosphere 0 1 1Sat Feb 29 18:42:01 2008 Stratosphere 1 1 1Sat Feb 29 18:42:01 2008 Skyline-asic 0 1 1Sat Feb 29 18:42:01 2008 Tuscany-asic 0 1 0Sat Feb 29 18:42:01 2008 X-Bus IO 0 6 0Sat Feb 29 18:42:01 2008 Power Mngmnt Epl 0 6 0switch#Table 8 describes the significant fields shown in the display.
This example shows how to display the OBFL exception log information:
switch# show logging onboard module 2 exception-logSun Feb 24 00:12:35 2008 : Exception Log RecordDevice Id : 60Device Name : DEV_SKYLINE_NIDevice Error Code : f(H)Device Error Name : SKY_NI_ERR_BM_B1_3_BIST_FAILEDSys Error : Skyline ni module experienced an errorErrtype : NON-CATASTROPHICPhyPortLayer : Fibre ChannelPort(s) Affected : 13-18Error Description : Skyline BM B1_3 BIST for interface 2 timed out during initDSAP : 0UUID : 0Time : Sun Feb 24 00:11:25 2008switch#Table 9 describes the significant fields shown in the display.
This example shows how to display the OBFL history information:
switch# show logging onboard module 2 obfl-historyOBFL history records:---------------------Sat Feb 29 30 18:09:57 2008 : OBFL all logs clearedSat Feb 29 18:47:53 2008 : OBFL miscellaneous-error logs clearedSat Feb 29 20:07:45 2008 : OBFL miscellaneous-error logs clearedswitch#The show logging onboard obfl-history command displays the following information:
•
•
•
This example shows how to display the OBFL kernel stack trace information:
switch# show logging onboard module 2 stack-trace==================== STACK TRACE ====================Logging time: Sat Feb 29 19:47:38 2008watchdog timeout: process swapper (0), jiffies 0x169bbStack: c0006e98 c001721c d195f5b4 c0005424 c0005500 c0003e90 c0005a2c c0005a40c0001a88 c01bf610 c0000394Call Trace:print_stack2_buf + 0x50kernel_thread + 0xb94klm_cctrl + 0x4554ppc_irq_dispatch_handler + 0x190do_IRQ + 0x3cret_from_intercept + 0x0probe_irq_mask + 0x494probe_irq_mask + 0x4a8transfer_to_handler + 0x15csoftnet_data + 0x2b0Registers:NIP: C0005A20 XER: 00000000 LR: C0005A2C SP: C01AA120 REGS: c01aa070 TRAP: 0500Tainted: PFMSR: 00009000 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 00DEAR: C0029B40, ESR: C01F0000MCSRR0: 00000000, MCSRR1: 00000000, MCAR: 00000000MCSR: 00000000 MCAR: 00000000 MCPSUMR: 00000000TASK = c01a8190[0] 'swapper' Last syscall: 120last math 00000000 last altivec 00000000 last spe 00000000GPR00: 00000000 C01AA120 C01A8190 00000000 00000032 C8F1DE28 D1010A9F 00000000GPR08: 0000180F C01FA39C D1010AA3 C01B8D18 24044244 1003A44C 0FFF6700 10049000GPR16: 0FFAE1B0 0FFFAC90 00000000 00000000 00000000 00000000 00000000 00000001GPR24: 00000000 00000000 00001160 007FFEAB 007FFE00 C01F0000 C01F0000 00000000The show logging onboard stack-trace command displays the following information:
•
•
•
•
•
•
This example shows how to display the OBFL error statistics:
switch# show logging onboard module 2 error-stats----------------------------OBFL Data forModule: 2----------------------------------------------------------------------------------------------------------ERROR STATISTICS INFORMATION FOR DEVICE ID 80 DEVICE Eureka------------------------------------------------------------------------------| | Time Stamp |In|PortError Stat Counter Name | Count |MM/DD/YY HH:MM:SS|st|Rang| | |Id|e------------------------------------------------------------------------------PB2_TX FlwCtrl from conn. ASIC > pe|0x1 |02/04/08 17:07:28|00|riod Intr | | | |PB2_TX FlwCtrl from conn. ASIC > pe|0x1 |02/06/08 10:54:44|00|riod Intr | | | |------------------------------------------------------------------------------ERROR STATISTICS INFORMATION FOR DEVICE ID 81 DEVICE Lamira------------------------------------------------------------------------------| | Time Stamp |In|PortError Stat Counter Name | Count |MM/DD/YY HH:MM:SS|st|Rang| | |Id|e------------------------------------------------------------------------------NF2 Interrupt - NH HIT error |0x1 |02/06/08 10:54:44|00|switch#Table 10 describes the significant fields shown in the display.
Related Commands
clear logging onboard
Clears the OBFL entries in the persistent log.
hw-module logging onboard
Enables or disabled OBFL entries based on the error type.
show logging onboard
To display the onboard failure log (OBFL), use the show logging onboard command.
show logging onboard {boot-uptime | device-version | endtime | environmental-history | error-stats [port number] | exception-log | interrupt-stats | module module | obfl-history | obfl-logs | stack-trace | starttime time [options] | status}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to show the OBFL from March 10, 2008 at 3:45 p.m.:
switch# show logging onboard starttime 03/10/08-15:45:00switch#show logging server
To display the syslog server configuration, use the show logging server command.
show logging server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the syslog server configuration:
switch# show logging serverswitch#Related Commands
show logging session status
To display the logging session status, use the show logging session status command.
show logging session status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging session status:
switch# show logging session statusswitch#show logging status
To display the logging status, use the show logging status command.
show logging status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging status:
switch# show logging statusswitch#show logging timestamp
To display the logging timestamp configuration, use the show logging timestamp command.
show logging timestamp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging time stamp configuration:
switch# show logging timestampswitch#Related Commands
show module
To display module information, use the show module command.
show module [slot {bandwidth-fairness | recovery-steps} | uptime | xbar [xbar-slot]]
Syntax Description
Defaults
Displays module information for all I/O modules and supervisor modules in the chassis.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
4.0(1)
This command was introduced.
4.1(2)
Output modified to show diagnostic events.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information for all modules in the chassis:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------7 48 1000 Mbps Optical Ethernet Modul N7K-M148GS-11 ok9 0 Supervisor module-1X N7K-SUP1 active *12 0 10/100/1000 Mbps Ethernet Module powered-dnMod Power-Status Reason--- ------------ ---------------------------12 powered-dn Configured Power downMod Sw Hw--- -------------- ------7 4.1(3) 0.2029 4.1(3) 0.805Mod MAC-Address(es) Serial-Num--- -------------------------------------- ----------7 00-1b-54-c2-ed-d0 to 00-1b-54-c2-ee-04 JAF1219AGFE9 00-1b-54-c0-ff-10 to 00-1b-54-c0-ff-18 JAB114000BVMod Online Diag Status--- ------------------7 Pass9 PassXbar Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------1 0 Fabric Module 1 N7K-C7018-FAB-1 okXbar Sw Hw--- -------------- ------1 NA 0.101Xbar MAC-Address(es) Serial-Num--- -------------------------------------- ----------1 NA JAF1225AGHJ* this terminal sessionswitch#This example shows how to display information for a specific module:
switch# show module 7Mod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------7 48 1000 Mbps Optical Ethernet Modul N7K-M148GS-11 okMod Sw Hw--- -------------- ------7 4.1(3) 0.202Mod MAC-Address(es) Serial-Num--- -------------------------------------- ----------7 00-1b-54-c2-ed-d0 to 00-1b-54-c2-ee-04 JAF1219AGFEMod Online Diag Status--- ------------------7 PassChassis Ejector Support: EnabledEjector Status:Left ejector CLOSE, Right ejector CLOSE, Module HW does not support ejector based shutdown.switch#This example shows how to display information for the fabric modules:
switch# show module xbarXbar Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------1 0 Fabric Module 1 N7K-C7018-FAB-1 okXbar Sw Hw--- -------------- ------1 NA 0.101Xbar MAC-Address(es) Serial-Num--- -------------------------------------- ----------1 NA JAF1225AGHJ* this terminal sessionswitch#Related Commands
show monitor
To display information about the Ethernet Switched Port Analyzer (SPAN), use the show monitor command.
show monitor
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about a SPAN:
switch(config)# show monitorSession State Reason Description------- ----------- ---------------------- -------------------------------1 down Session admin shut6 down Session admin shut8 down Session admin shut9 down Session admin shutswitch(config)#Related Commands
show running-config monitor
Displays the running configuration to the startup configuration.
show startup-config monitor
Displays information about the startup SPAN configuration.
show monitor session
To display information about an Ethernet switched port analyzer (SPAN) session for analyzing traffic between ports, use the show monitor session command.
show monitor session {all | session_number | range session_range} [brief]
Syntax Description
Defaults
Displays a brief summary of information for all configured SPAN sessions.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a brief summary of information for all configured SPAN sessions:
switch# show monitor sessionSession State Reason Description------- ----------- ---------------------- --------------------------------1 down Session admin shut6 down Session admin shut8 down Session admin shutswitch#This example shows how to display detailed information for all configured SPAN sessions:
switch# show monitor session allsession 1---------------type : localstate : down (Session admin shut)source intf :rx :tx :both :source VLANs :rx :tx :both :filter VLANs : filter not specifieddestination ports :Legend: f = forwarding enabled, l = learning enabledsession 8---------------type : localstate : down (Session admin shut)source intf :rx : Eth7/2tx : Eth7/2both : Eth7/2source VLANs :rx :tx :both :filter VLANs : filter not specifieddestination ports :Legend: f = forwarding enabled, l = learning enabledswitch#This example shows how to display a brief summary of information for SPAN session number 1:
switch# show monitor session 1 briefsession 1---------------type : localstate : down (Session admin shut)switch#Related Commands
monitor session
Places you into monitor configuration mode for configuring a SPAN session.
show ntp access-groups
To display the Network Time Protocol (NTP) access group configuration, use the show ntp access-groups command.
show ntp access-groups
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP access group configuration:
switch(config)# show ntp access-groups--------------------------------------Access List Type--------------------------------------Admin_Group_123 Peerswitch(config)#Related Commands
show ntp authentication-keys
To display the Network Time Protocol (NTP) authentication keys, use the show ntp authentication-keys command.
show ntp authentication-keys
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP authentication keys:
switch(config)# show ntp authentication-keys-----------------------------Auth key MD5 String-----------------------------3 cisco42 Nice_Key34567 nexus7kswitch(config)#Related Commands
show ntp authentication-status
To display the status of the Network Time Protocol (NTP) authentication, use the show ntp authentication-status command.
show ntp authentication-status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP authentication status:
switch(config)# show ntp authentication-statusAuthentication enabled.switch(config)#Related Commands
ntp autheticate
Enables NTP authentication.
show ntp authentication-keys
Displays the configured NTP authentication keys.
show ntp internal
To display the Network Time Protocol (NTP) internal information, use the show ntp internal command.
show ntp internal {event-history [config | fsm | msgs | rts | tstamp] | mem-stats [detail] | module-info}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP internal information:
switch(config)# show ntp internal module-infoNumber of Linecards present = 4Timestamp check (configured) = enabledTimestamp check status = disabledEnable/Disable status---------------------User : not disabledSUP : not disabledFabric : not disabledswitch(config)#Related Commands
show running-config ntp
Displays the NTP information.
show ntp statistics
Displays the NTP statistics.
show ntp logging-status
To display the Network Time Protocol (NTP) logging status, use the show ntp logging-status command.
show ntp logging-status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP logging status:
switch(config)# show ntp logging-statusNTP logging enabled.switch(config)#Related Commands
show ntp peers
To display the configured Network Time Protocol (NTP) servers and peers, use the show ntp peers command.
show ntp peers
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
A domain name is resolved only when you have a domain name server (DNS) server configured.
This command does not require a license.
Examples
This example shows how to display all the configured NTP servers and peers:
switch(config)# show ntp peers--------------------------------------------------Peer IP Address Serv/Peer--------------------------------------------------2001:db8::4101 Peer (configured)192.0.2.10 Server (configured)switch(config)#Related Commands
ntp server
Configures an NTP server.
ntp peer
Configures an NTP peer.
show ntp peer-status
Displays the status of all the server and peers.
show ntp peer-status
To do display the status of the Network Time Protocol (NTP) peers, use the show ntp peer-status command.
show ntp peer-status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the peer status for NTP:
switch(config)# show ntp peer-statusRelated Commands
show ntp pending-diff
To display the differences between the pending Network Time Protocol (NTP) configuration and the active NTP configuration, use the show ntp pending-diff command.
show ntp pending-diff
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the differences between the pending NTP configuration and the active NTP configuration:
switch# show ntp pending-diffswitch#Related Commands
show ntp source
Displays information about the NTP source.
show ntp peers
Displays information about NTP peers.
show ntp pending peers
To display pending Network Time Protocol (NTP) configuration changes on all peers, use the show ntp pending peers command.
show ntp pending peers
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the pending NTP configuration changes on all peers:
switch# show ntp pending peersswitch#Related Commands
show ntp source
Displays information about the NTP source.
show ntp peers
Displays information about NTP peers.
show ntp session status
To display the Network Time Protocol (NTP) session status, use the show ntp session status command.
show ntp session status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP session status:
switch# show ntp session statusLast Action Time Stamp : Thu Aug 1 16:22:00 20Last Action : Distribution EnableLast Action Result : SuccessLast Action Failure Reason : noneswitch#Related Commands
show ntp source
Displays information about the NTP source.
show ntp peers
Displays information about NTP peers.
show ntp status
To display the Network Time Protocol (NTP) distribution status, use the show ntp status command.
show ntp status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP distribution status:
switch(config)# show ntp statusDistribution : DisabledLast operational state: No sessionswitch(config)#Related Commands
show ntp source
Displays information about the NTP source.
show ntp peers
Displays information about NTP peers.
show ntp rts-update
To display if the request to send (RTS) update is enabled, use the show ntp rts-update command.
show ntp rts-update
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to view RTS-update information:
switch(config)# show ntp rts-updateRTS update is enabledswitch(config)#Related Commands
show ntp source
To display information about the Network Time Protocol (NTP) source, use the show ntp source command.
show ntp source
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP source information:
switch(config)# show ntp sourceRelated Commands
show ntp source-interface
To display the Network Time Protocol (NTP) source interface, use the show ntp source-interface command.
show ntp source-interface
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP source interface:
switch(config)# show ntp source-interfaceSource interface loopback1switch(config)#Related Commands
show ntp statistics
To display Network Time Protocol (NTP) statistics, use the show ntp statistics command.
show ntp statistics {io | local | memory | peer {ipaddr address | name name1 [..namen]}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to displays statistics for NTP:
switch(config)# show ntp statistics localRelated Commands
show ntp status
To display the Network Time Protocol (NTP) distribution status, use the show ntp status command.
show ntp status [ > | >> | | ]
Syntax Description
>
(Optional) Redirects the command output to a file.
>>
(Optional) Redirects the command output to a file in append mode.
|
(Optional) Pipes the command output to a filter.
Defaults
Disabled
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command shows whether Cisco Fabric Services (CFS) is enabled or disabled for the NTP application and whether a fabric lock is in place because a configuration is in progress.
This command does not require a license.
Examples
This example shows how to display the CFS distribution status for NTP. In this example, CFS distribution is enabled and the fabric is locked. When a configuration is in progress on a CFS-enabled device, the fabric is locked until the change is committed and the configuration is distributed throughout the fabric. The lock prevents multiple configurations occurring at the same time.
switch(config)# show ntp status
Distribution : Enabled
Last operational state: Fabric Locked
Related Commands
show ntp trusted-keys
To display the configured Network Time Protocol (NTP) trusted keys, use the show ntp trusted-keys command.
show ntp trusted-keys
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display all the configured NTP trusted keys:
switch(config)# show ntp trusted-keysTrusted Keys:42switch(config)#Related Commands
show platform hardware capacity interface resources
To display a summary of current platform hardware resource utilization, use the show platform hardware capacity interface resources command.
show platform hardware capacity interface resources
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a summary of current platform hardware resource utilization:
switch# show platform hardware capacity interface resourcesInterface ResourcesInterface drops:Module Total drops: Tx Rx Highest drop port: Tx Rx7 0 0 - -Interface buffer sizes:Module Bytes: Tx buffer Rx buffer7 6452775 7743330Related Commands
show port-monitor
To display information about the Simple Network Management Protocol (SNMP) port-monitor configuration, use the show port-monitor command.
show port-monitor [policy-name]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP port-monitor information:
switch(config)# show port-monitor name pm2switch(config-port-monitor)# show port-monitor pm2Policy Name : pm2Admin status : Not ActiveOper status : Not ActivePort type : All Ports-------------------------------------------------------------------------------------------Counter Threshold Interval Rising Threshold event Falling Threshold event In Use------- --------- -------- ---------------- ----- ------------------ ----- ------Link Loss Delta 60 5 4 1 4YesSync Loss Delta 60 5 4 1 4YesProtocol Error Delta 60 1 4 0 4YesSignal Loss Delta 60 5 4 1 4YesInvalid Words Delta 60 1 4 0 4YesInvalid CRC's Delta 60 5 4 1 4YesRX Performance Delta 60 2147483648 4 524288000 4YesTX Performance Delta 60 2147483648 4 524288000 4Yes--------------------------------------------------------------------------------switch(config-port-monitor)#Related Commands
show port-monitor status
Displays the port-monitor status.
show port-monitor active
Displays active port-monitor policies.
show port-monitor active
To display information about the active Simple Network Management Protocol (SNMP) port-monitor policies, use the show port-monitor active command.
show port-monitor active
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the active SNMP port-monitor policies:
switch(config)# show port-monitor activePolicy Name : testAdmin status : ActiveOper status : ActivePort type : All Ports-------------------------------------------------------------------------------------------Counter Threshold Interval Rising Threshold event Falling Threshold event In Use------- --------- -------- ---------------- ----- ------------------ ----- ------Link Loss Delta 60 5 4 1 4YesSync Loss Delta 60 5 4 1 4YesProtocol Error Delta 60 1 4 0 4YesSignal Loss Delta 60 5 4 1 4YesInvalid Words Delta 60 1 4 0 4YesInvalid CRC's Absolute 30 10000000 100 1 4YesRX Performance Delta 60 2147483648 4 524288000 4YesTX Performance Delta 60 2147483648 4 524288000 4Yes-------------------------------------------------------------------------------------------switch(config)#Related Commands
show port-monitor status
Displays the port-monitor status.
show port-monitor active
Displays active port-monitor policies.
show port-monitor status
To display information about the Simple Network Management Protocol (SNMP) port-monitor status, use the show port-monitor status command.
show port-monitor status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP port-monitor status:
switch(config)# show port-monitor statusPort Monitor : EnabledActive Policies : NoneLast 10 logs :switch(config-port-monitor)#Related Commands
show port-monitor active
Displays active port-monitor policies.
show port-monitor
Displays information about the port-monitor configuration.
show processes
To display the process information for a device, use the show processes command.
show processes [vdc vdc-number]
Syntax Description
Defaults
Displays information for all processes in the local device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
You can specify another VDC only from the default VDC.
This command does not require a license.
Examples
This example shows how to display the process information for a device:
switch# show processesPID State PC Start_cnt TTY Type Process----- ----- -------- ----------- ---- ---- -------------1 S b7f9e468 1 - O init2 S 0 1 - O migration/03 S 0 1 - O ksoftirqd/04 S 0 1 - O desched/05 S 0 1 - O migration/16 S 0 1 - O ksoftirqd/17 S 0 1 - O desched/18 S 0 1 - O events/09 S 0 1 - O events/110 S 0 1 - O khelper15 S 0 1 - O kthread...This example shows how to display the process information for another VDC:
switch# show processes vdc 2PID State PC Start_cnt TTY Type Process----- ----- -------- ----------- ---- ---- -------------1 S b7f9e468 1 - O init2 S 0 1 - O migration/03 S 0 1 - O ksoftirqd/04 S 0 1 - O desched/05 S 0 1 - O migration/16 S 0 1 - O ksoftirqd/17 S 0 1 - O desched/18 S 0 1 - O events/09 S 0 1 - O events/110 S 0 1 - O khelper15 S 0 1 - O kthread...show processes cpu
To display the CPU utilization information for processes on the device, use the show processes cpu command.
show processes cpu
Syntax Description
This command has no arguments or keywords.
Defaults
Displays information for all processes in the local device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the CPU utilization information for the processes:
switch# show processes cpuPID Runtime(ms) Invoked uSecs 1Sec Process----- ----------- -------- ----- ----- -----------1 286 315748 0 0 init2 302 636268 0 0 migration/03 1586 72636726 0 0 ksoftirqd/04 502 1345165 0 0 desched/05 1956 559740 3 0 migration/16 2218 457761883 0 0 ksoftirqd/17 2325 1469647 1 0 desched/18 1158 794795 1 0 events/09 1258 721210 1 0 events/110 62 2779 22 0 khelper15 0 30 25 0 kthread24 0 2 5 0 kacpid102 201 286 704 0 kblockd/0103 276 516 535 0 kblockd/1116 0 5 17 0 khubd...show processes cpu history
To display information about the CPU utilization by the system processes in the last 60 seconds, 60 minutes, and 72 hours in a graphical format, use the show processes cpu history command.
show processes cpu history
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the CPU utilization by the system processes for last 60 seconds, 60 minutes, and 72 hours in a graphical format:
switch(config)# show processes cpu history92 5 4 73 474 64 65 575 4720632455154353422664436813510334334313331390123633453843191510090 #80 # #70 # # # # # #60 # # # # # # ## #50 # # # # ## # ## ### #40 # # # # ### ## ## ### ##30 # # # ## ### ## ## ### ##20 ## # # ## ### ## ## ### ##10 ### ## # # ### ## ### ## ## ### # ### # #0....5....1....1....2....2....3....3....4....4....5....5....0 5 0 5 0 5 0 5 0 5CPU% per second (last 60 seconds)# = average CPU%1115142211111112111121121211221225221222212223131221222321228691803099939940698909508897067152279112053112804239253359141009080706050 * *40 * * *30 * * * * ** * * * * **20 *********** ** ********************************* ***********10 ***#*****************************#**************************0....5....1....1....2....2....3....3....4....4....5....5....0 5 0 5 0 5 0 5 0 5CPU% per minute (last 60 minutes)* = maximum CPU% # = average CPU%556655555556565565556566666666665666666566555556555555555555565666656665100908070605040302010 ************************************************************************0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.0 5 0 5 0 5 0 5 0 5 0 5 0CPU% per hour (last 72 hours)* = maximum CPU% # = average CPU%Related Commands
show processes cpu
Displays the CPU utilization information for processes on the device.
show system resources
Displays the system resources.
show process cpu sort
To display information about CPU processes sorted by CPU utilization, use the show process cpu sort command.
show process cpu sort
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
The modules perform the polling and send messages to the Supervisor module for Simple Network Management Protocol (SNMP) caching. When attached to a module under no load, the CPU spikes approximately every 10 seconds for a short period of time. The name of the process is statsclient.
The CPU spike can go up to 100 percent for a few miliseconds. The process is preemptive and it does not block other high priority processes.
This command does not require a license.
Examples
This example shows how to display information about CPU processes sorted by CPU utilization:
switch(config)# show process cpu sortPID Runtime(ms) Invoked uSecs 1Sec Process----- ----------- -------- ----- ------ -----------3622 2335 6843 341 50.0% pfstat1 2550 4169 611 0.0% init2 13 2676 4 0.0% migration/03 2091 883525 2 0.0% ksoftirqd/04 48 6300 7 0.0% desched/05 10 2816 3 0.0% migration/16 21 4450597 0 0.0% ksoftirqd/17 42 6416 6 0.0% desched/18 1785 8581 208 0.0% events/09 1560 7426 210 0.0% events/110 58 2731 21 0.0% khelper15 0 30 25 0.0% kthread24 0 2 5 0.0% kacpid104 12 201 62 0.0% kblockd/0105 4 138 33 0.0% kblockd/1118 0 5 17 0.0% khubd185 0 4 3 0.0% pdflush186 139 3010 46 0.0% pdflush187 0 1 5 0.0% kswapd0--More--
Note
Related Commands
show processes log
To display the contents of the process log, use the show processes log command.
show processes log [details | pid process-id | vdc-all]
Syntax Description
Defaults
Displays summary information for all processes on the device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display summary information from the process log:
switch# show processes logVDC Process PID Normal-exit Stack Core Log-create-time--- --------------- ------ ----------- ----- ----- ---------------1 aclmgr 3632 N Y N Thu Mar 13 21:37:07 20081 aclmgr 4182 N Y N Wed Mar 12 13:45:38 20081 aclmgr 4205 N Y N Wed Mar 12 13:45:38 20081 adjmgr 4333 N N N Sat Nov 24 06:25:20 20071 arbiter 4332 N Y N Mon Nov 19 10:14:42 20071 arp 3870 N Y N Sat Dec 22 12:02:46 20071 clis 10005 N Y N Sat Nov 24 03:46:13 20071 clis 10268 N N N Fri Dec 14 09:13:53 20071 clis 1040 N Y N Fri Nov 16 13:34:30 2007...This example shows how to display detailed information from the process log:
switch# show processes log details======================================================Service: aclmgrDescription: ACL MgrStarted at Thu Mar 13 20:34:35 2008 (507163 us)Stopped at Thu Mar 13 20:37:07 2008 (664205 us)Uptime: 2 minutes 32 secondsStart type: SRV_OPTION_RESTART_STATELESS (23)Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)System image name: n7000-s1-dk9.4.0.1.gbinSystem image version: 4.0(1) S7PID: 3632Exit code: signal 11 (core dumped)CWD: /var/sysmgr/workVirtual Memory:CODE 08048000 - 0811CCF4DATA 0811DCF4 - 0811EBE8BRK 08121000 - 08259000STACK BFFFE270TOTAL 47244 KBRegister Set:EBX B7D64CD0 ECX 00000001 EDX 00000001ESI 41170040 EDI 00000000 EBP BFFFD1C8EAX 00000401 XDS C010007B XES 0000007BEAX FFFFFFFF (orig) EIP B7D5BEF2 XCS 00000073EFL 00010292 ESP BFFFD1C0 XSS 0000007BStack: 4272 bytes. ESP BFFFD1C0, TOP BFFFE2700xBFFFD1C0: B7D5BEE0 B7D64CD0 BFFFD1D8 B7D5C381 .....L..........0xBFFFD1D0: B7D2614C FF000226 BFFFD218 B7D232BA La..&........2..0xBFFFD1E0: B5542014 B7D25DE0 000007DE B5542014 . T..]....... T.0xBFFFD1F0: B7D08918 B7D2614C FF000226 08241A54 ....La..&...T.$.0xBFFFD200: B5542014 41170034 08241A54 B7D2614C . T.4..AT.$.La..0xBFFFD210: FF000226 BFFFD2D0 BFFFD278 B7D138CE &.......x....8..0xBFFFD220: 08246A04 08230074 BFFFD2D0 B7D5A24D .j$.t.#.....M...0xBFFFD230: B7D6369A 00002000 00000004 00000000 .6... ..........0xBFFFD240: 0000C005 00002000 BFFFD278 B7D3CF90 ..... ..x..........This example shows how to display detailed information from the process log for a specific process:
switch# show processes pid 3632======================================================Service: arpDescription: Address Resolution Protocol (ARPStarted at Sat Dec 22 12:02:19 2007 (216828 us)Stopped at Sat Dec 22 12:02:44 2007 (496964 us)Uptime: 25 secondsStart type: SRV_OPTION_RESTART_STATELESS (23)Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)System image version: 4.0(0.788) S16PID: 3912Exit code: signal 11 (core dumped)Threads: 3906 3905 4066 3917 3884 3870CWD: /var/sysmgr/workVirtual Memory:CODE 08048000 - 08071474DATA 08072474 - 08074794BRK 08075000 - 080DE000STACK BFFFEB80TOTAL 107908 KBRegister Set:EBX B7EF4264 ECX B53F45CA EDX B8009B1EESI B601C003 EDI B53F45C8 EBP B53F4578EAX B8009B1E XDS 0000007B XES 0000007BEAX FFFFFFFF (orig) EIP B7EDF9AB XCS 00000073EFL 00010286 ESP B53F4560 XSS 0000007BStack: 2688 bytes. ESP B53F4560, TOP BFFFEB800xB53F4560: B601C003 00000001 F1EC838D B7EF4264 ............dB..0xB53F4570: 00000000 00000000 B53F45D8 B7EE0C0D .........E?.....0xB53F4580: B601C003 B53F45CA B53F45C8 B53F45C0 .....E?..E?..E?.0xB53F4590: 00000001 B53F45C4 00000000 00000001 .....E?............This example shows how to display process log information for all VDCs on the physical device:
switch# show processes log vdc-allVDC Process PID Normal-exit Stack Core Log-create-time--- --------------- ------ ----------- ----- ----- ---------------1 aclmgr 3632 N Y N Thu Mar 13 21:37:07 20081 aclmgr 4182 N Y N Wed Mar 12 13:45:38 20081 aclmgr 4205 N Y N Wed Mar 12 13:45:38 20081 adjmgr 4333 N N N Sat Nov 24 06:25:20 20071 arbiter 4332 N Y N Mon Nov 19 10:14:42 20071 arp 3870 N Y N Sat Dec 22 12:02:46 20071 clis 10005 N Y N Sat Nov 24 03:46:13 20071 clis 10268 N N N Fri Dec 14 09:13:53 20071 clis 1040 N Y N Fri Nov 16 13:34:30 20071 clis 10486 N Y N Fri Nov 16 14:58:59 20071 clis 10646 N Y N Fri Nov 16 14:59:45 2007...show processes memory
To display the memory allocation information for processes, use the show processes memory command.
show processes memory [shared]
Syntax Description
Defaults
Displays memory allocated to the processes.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about memory allocation for processes:
switch# show processes memoryPID MemAlloc StackBase/Ptr Process----- -------- ----------------- ----------------1 147456 bffffda0/bffff890 init2 0 0/0 migration/03 0 0/0 ksoftirqd/04 0 0/0 desched/05 0 0/0 migration/16 0 0/0 ksoftirqd/17 0 0/0 desched/18 0 0/0 events/09 0 0/0 events/110 0 0/0 khelper15 0 0/0 kthread24 0 0/0 kacpid...This example shows how to display information about shared memory allocation for processes:
switch# show processes memory sharedComponent Shared Memory Size Used Available ReferenceAddress (kbytes) (kbytes) (kbytes) Countsmm 0X60000000 1024 3 1021 115cli 0X60110000 24576* 13991 10585 84am 0X61920000 14336* 14 14322 7urib 0X62730000 32768* 648 32120 25u6rib-ufdm 0X64740000 320* 188 132 2urib-redist 0X647A0000 4096* 0 4096 25icmpv6 0X64BB0000 2048 0 2048 2ip 0X64DC0000 8192 65 8127 23urib-ufdm 0X655D0000 2048* 0 2048 2u6rib 0X657E0000 16384* 507 15877 12ipv6 0X667F0000 8192 2 8190 9u6rib-notify 0X67000000 2048* 681 1367 12rpm 0X67210000 2048 6 2042 11mrib 0X67420000 40960 2 40958 3mrib-mfdm 0X69C30000 5120 0 5120 2m6rib 0X6A140000 10240 2 10238 3m6rib-mfdm 0X6AB50000 2048 10 2038 2igmp 0X6AD60000 8192 0 8192 2bgp 0X6B570000 8192 182 8010 1Shared memory totals - Size: 189 MB, Used: 16 MB, Available: 173 MBFree Physical Memory: 0 MB kernel, 0 MB userRelated Commands
show processes
Displays process information.
show startup-config
Displays the startup configuration.
show ptp brief
To display a brief status of the Precision Time Protocol (PTP) interfaces, use the show ptp brief command.
show ptp brief
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a brief status of the PTP interfaces:
switch# show ptp briefPTP port status-----------------------Port State------- --------------Eth7/10 PassiveEth7/1 SlaveRelated Commands
show ptp clock
To display the Precision Time Protocol (PTP) clock information, use the show ptp clock command.
show ptp clock
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the PTP clock information:
switch# show ptp clockPTP Device Type: Boundary clockClock Identity : 0:18:ba:ff:ff:d8: e:17Clock Domain: 0Number of PTP ports: 2Priority1 : 255Priority2 : 255Clock Quality:Class : 248Accuracy : 254Offset (log variance) : 65535Offset From Master : 0Mean Path Delay : 0Steps removed : 1Local clock time:Sun Jan 15 20:57:29 2011Related Commands
show ptp clocks foreign-masters-record
To display information about the state of foreign masters known to the Precision Time Protocol (PTP) process, use the show ptp clocks foreign-masters-record command.
show ptp clocks foreign-masters-record {interface [ethernet]}
Syntax Description
T
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the state of foreign masters known to the PTP process:
switch# show ptp clocks foreign-masters-record interface ethernet 7/1RP/0/0/CPU0:demo#show ptp clocks foreign-mastersP1=Priority1, P2=Priority2, C=Class, A=Accuracy,OSLV=Offset-Scaled-Log-Variance, SR=Steps-RemovedGM=Is grandmaster--------- ----------------------- --- ---- ---- --- ----- --------Interface Clock-ID P1 P2 C A OSLV SR--------- ----------------------- --- ---- ---- --- ----- --------Eth7/10 0:18:ba:ff:ff:d8: e:16 255 255 248 254 65535 0 GMEth7/1 0:18:ba:ff:ff:d8: e:16 255 255 248 254 65535 0 GMRelated Commands
show ptp corrections
To display the history of the Precision Time Protocol (PTP) clock corrections on the Ethernet interfaces, use the show ptp corrections command.
show ptp corrections
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the history of the PTP clock corrections on the Ethernet interfaces:
switch# show ptp correctionsPTP corrections------------------------------------------Slave Port Sup time Corrections(s,ns)---------- -------------------- ------------Eth7/10 2010 Mar 11 03:14:55 -1 1210900Eth7/10 2010 Mar 11 03:14:55 -340978Related Commands
show ptp parent
To display information about the parent and grand master of the Precision Time Protocol (PTP) clock, use the show ptp parent command.
show ptp parent
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the parent and grand master of the PTP clock:
switch# show ptp parentParent Clock:Parent Clock Identity: 0:18:ba:ff:ff:d8: e:16Parent Port Number: 1546Observed Parent Offset (log variance): N/AObserved Parent Clock Phase Change Rate: N/AGrandmaster Clock:Grandmaster Clock Identity: 0:18:ba:ff:ff:d8: e:16Grandmaster Clock Quality:Class: 248Accuracy: 254Offset (log variance): 65535Priority1: 255Priority2: 255Related Commands
show ptp port
To display information about the Precision Time Protocol (PTP) port, use the show ptp port command.
show ptp port {interface [ethernet]}
Syntax Description
T
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the PTP port:
switch# show ptp portPTP Port Dataset: Eth7/1Port identity: clock identity: 0:18:ba:ff:ff:d8: e:17Port identity: port number: 1536PTP version: 2Port state: SlaveDelay request interval(log mean): 2Announce receipt time out: 3Peer mean path delay: 0Announce interval(log mean): 1Sync interval(log mean): 2Delay Mechanism: End to EndPeer delay request interval(log mean): 0Related Commands
show ptp time-property
To display the Precision Time Protocol (PTP) clock properties, use the show ptp time-property command.
show ptp time-property
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the PTP clock properties:
switch# show ptp time-propertyPTP CLOCK TIME PROPERTY:Current UTC Offset valid: 0Current UTC Offset: 33Leap59: 0Leap61: 0Time Traceable: 0Frequency Traceable: 0PTP Timescale: 0Time Source: 0xA0(internal Osccilator)Related Commands
show redundancy status
To show detailed information about redundancy, use the show redundancy status command.
show redundancy status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to displays redundancy information:
switch# show redundancy statusRedundancy mode---------------administrative: HAoperational: NoneThis supervisor (sup-6)-----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with no standbyOther supervisor (sup-5)------------------------Redundancy state: Not presentSupervisor state: N/AInternal state: N/ASystem start time: Fri Aug 15 15:55:19 2008System uptime: 3 days, 23 hours, 57 minutes, 22 secondsKernel uptime: 4 days, 0 hours, 1 minutes, 39 secondsActive supervisor uptime: 3 days, 23 hours, 57 minutes, 22 secondssshow rmon
To display the configuration or onboard logs, use the show rmon command.
show rmon {alarms | events | hcalarms | logs | status}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the configured RMON alarms:
switch# show rmon alarmsAlarm 20 is active, owned by testMonitors 1.3.6.1.2.1.2.2.1.16.30 every 30 second(s)Taking delta samples, last value was 17Rising threshold is 15, assigned to event 1Falling threshold is 0, assigned to event 0On startup enable rising or falling alarmThis example shows how to display the configured RMON events:
switch# show rmon eventsEvent 4 is active, owned by administrator@london_op_centerDescription is WARNING(4)Event firing causes log and trap to community public, last fired 03:32:43This example shows how to display the configured high-capacity RMON alarms:
switch# show rmon hcalarmsHigh Capacity Alarm 1 is active, owned by cseSysCPUUtilization.0@testMonitors 1.3.6.1.4.1.9.9.305.1.1.1.0 every 10 second(s)Taking absolute samples, last value was 0Rising threshold is 60, assigned to event 4Falling threshold is 59, assigned to event 4On startup enable rising alarmThis example shows how to display RMON configuration and logged information:
switch# show rmon statusMaximum allowed 32 bit or 64 bit alarms : 512Number of 32 bit alarms configured : 0Number of 64 bit hcalarms configured : 0switch#Related Commands
rmon alarm
Configures the 32-bit RMON alarm.
rmon event
Configures an RMON event.
rmon hcalarm
Configures the 64-bit RMON alarm.
show running-config cdp
To display the Cisco Discovery Protocol (CDP) running configuration, use the show running-config cdp command.
show running-config cdp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the CDP running configuration with defaults:
switch(config)# show running-config cdp all!Command: show running-config cdp all!Time: Fri Jan 15 22:19:20 2010version 5.0(2)logging level cdp 6cdp advertise v2cdp enablecdp holdtime 180cdp timer 60cdp format device-id system-nameinterface Ethernet6/1cdp enableinterface Ethernet6/2cdp enableinterface Ethernet6/3cdp enableinterface Ethernet6/4cdp enableinterface Ethernet6/5cdp enableinterface Ethernet6/6cdp enableinterface Ethernet6/7cdp enableinterface Ethernet6/8cdp enableinterface Ethernet7/1cdp enableinterface Ethernet7/2cdp enableinterface Ethernet7/3cdp enableinterface Ethernet7/4cdp enableinterface Ethernet7/5cdp enableinterface Ethernet7/6cdp enableinterface Ethernet7/7cdp enableinterface Ethernet7/8cdp enable--More--switch(config)#Related Commands
show running-config diagnostic
To display the running-configuration diagnostics, use the show running-config diagnostic command.
show running-config diagnostic [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the running-configuration diagnostics:
switch(config)# show running-config diagnostic all!Command: show running-config diagnostic all!Time: Fri Jan 15 22:22:01 2010version 5.0(2)diagnostic bootup level completeswitch(config)#Related Commands
show running-config eem
To display the Embedded Event Manager (EEM) running configuration, use the show running-config eem command.
show running-config eem
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the Embedded Event Manager (EEM) running configuration:
switch# show running-config eemswitch(config)# show running-config eem!Command: show running-config eem!Time: Fri Jan 15 22:23:28 2010version 5.0(2)switch(config)#show running-config lldp
To display the global Link Layer Discovery Protocol (LLDP) configuration, use the show running-config lldp command.
show running-config lldp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the global LLDP configuration:
switch(config)# show running-config lldp!Command: show running-config lldp!Time: Mon Jan 11 02:19:29 2010version 5.0(2)feature lldplogging level lldp 5switch(config)#Related Commands
show running-config monitor
To display information about the running Ethernet switched port analyzer (SPAN) configuration on the system, use the show running-config monitor command.
show running-config monitor [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the running SPAN configuration on the system:
switch(config)# show running-config monitor!Command: show running-config monitor!Time: Fri Jan 15 22:24:43 2010version 5.0(2)logging level monitor 6switch(config)#Related Commands
show monitor
Displays information about the SPAN configuration.
show startup-config monitor
Displays information about the startup SPAN configuration.
show running-config netflow
To display the NetFlow configuration that is currently on your switch, use the show running-config netflow command.
show running-config netflow [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NetFlow configuration that is running on the switch:
switch(config)# show running-config netflow all!Command: show running-config netflow all!Time: Fri Jan 15 22:26:04 2010version 5.0(2)feature netflowflow timeout active 1800flow timeout inactive 15flow exporter new_flow_1transport udp 9995dscp 0version 5flow exporter new_flow_2transport udp 9995dscp 0version 9template data timeout 1800flow exporter testtransport udp 9995dscp 0version 9template data timeout 1800flow exporter Custom-Flow-Exporter-1transport udp 9995dscp 0version 9template data timeout 1800option exporter-stats timeout 1200switch(config)#Related Commands
show running-config ntp
To display the Network Time Protocol (NTP) configuration that is currently running on the system, use the show running-config ntp command.
show running-config ntp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP configuration that is currently running:
switch(config)# show running-config ntp!Command: show running-config ntp!Time: Fri Jan 15 22:28:34 2010version 5.0(2)ntp server 190.0.2.10ntp server 192.0.2.10 prefer use-vrf RED key 786ntp peer 2001:db8::4101ntp authentication-key 3 md5 fewhg 7ntp authentication-key 34567 md5 qabzk7f 7ntp loggingntp access-group peer abcd*123switch(config)#Related Commands
show ntp source-interface
Displays information about the NTP source interface.
show startup-config ntp
Displays information about the startup NTP configuration of the switch.
show running-config snmp
To display the running Simple Network Management Protocol (SNMP) configuration of a system, use the show running-config snmp command.
show running-config snmp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the running SNMP configuration of a system:
switch(config)# show running-config snmp!Command: show running-config snmp!Time: Fri Jan 15 22:30:27 2010version 5.0(2)snmp-server user admin network-admin auth md5 0x1dc65f45a9d8e41dbccd76380946d6c3priv 0x1dc65f45a9d8e41dbccd76380946d6c3 localizedkeyswitch(config)#Related Commands!Command: show running-config snmp
Related Commands!Time: Tue Feb 2 22:30:27 2010
Related Commands
Related Commandsversion 5.0(2)
Related Commandssnmp-server user admin network-admin auth md5 0x1dc65f45a9d8e41dbccd76380946d6c3
Related Commands priv 0x1dc65f45a9d8e41dbccd76380946d6c3 localizedkey
Related Commands
Related Commands
Related Commandsswitch(config)#
Related Commands
show startup-config snmp
Displays the startup SNMP configuration.
show port-monitor active
Displays active port-monitor policies.
show sampler
To display a NetFlow sampler, use the show sampler command.
show sampler [name] [sampler-name]
Syntax Description
name
(Optional) Specifies a sampler.
sampler-name
(Optional) Sampler name. The maximum number of characters is 32.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You can create a sampler to define the NetFlow sampling rate for a flow.
This command does not require a license.
Examples
This example shows how to display a NetFlow sampler:
switch(config)# show samplerSampler Netflow-Sampler-1:mode 1 out-of 1000switch(config)#Related Commands
sampler
Configures a sampler to collect data for a user selected packet ratio to preserve hardware resources.
show scheduler
To display information about scheduled maintenance jobs, use the show scheduler command.
show scheduler {config | internal [mem-stats] | job [name jobname] | logfile | schedule [name schedulename]}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
To use this command, the scheduler must already be enabled.
To enable the scheduler, use the feature scheduler command.
This command does not require a license.
Examples
This example shows how to display the scheduler configuration:
switch# show scheduler configconfig terminalfeature schedulerscheduler logfile size 16endconfig terminalscheduler job name test-1endconfig terminalscheduler job name testendconfig terminalscheduler job name test1endconfig terminalscheduler job name test2endswitch#This example shows how to display the specified scheduler timetable:
switch# show scheduler schedule name testSchedule Name : test------------------------------------User Name : adminSchedule Type : Run once on Tue Aug 10 09:48:00 2008Last Execution Time: Tue Aug 10 09:48:00 2008-----------------------------------------------Job Name Status-----------------------------------------------addMem Success (0)Related Commands
scheduler
Configures maintenance jobs.
feature scheduler
Enables the scheduler feature for scheduling maintenance jobs.
show snmp
To display Simple Network Management Protocol (SNMP) information, use the show snmp command.
show snmp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP information:
switch(config)# show snmpsys contact:sys location: anyplace, Anywhere0 SNMP packets input0 Bad SNMP versions0 Unknown community name0 Illegal operation for community name supplied0 Encoding errors0 Number of requested variables0 Number of altered variables0 Get-request PDUs0 Get-next PDUs0 Set-request PDUs0 SNMP packets output0 Too big errors0 No such name errors0 Bad values errors0 General errorsCommunity Group / Access--------- ---------------Comm2 network-admintestCommunity vdc-operatorcom3 vdc-admin______________________________________________________________SNMP USERS______________________________________________________________User Auth Priv(enforce) Groups____ ____ _____________ ______foo md5 aes-128(no) network-operatorvdc-adminnetwork-adminUser3 md5 no network-operatoradmin md5 des(no) network-adminuser1 md5 des(no) vdc-admin______________________________________________________________NOTIFICATION TARGET USERS (configured for sending V3 Inform)______________________________________________________________User Auth Priv____ ____ ____foo md5 no(EngineID 11:22:33:44:55)foo sha no(EngineID 33:0:33:22:33)SNMP Tcp Authentication Flag : Enabled.Related Commands
show snmp community
To display the Simple Network Management Protocol (SNMP) community strings, use the show snmp community command.
show snmp community
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
Use the show snmp community command to display a list of SNMP communities configured on a device.
In Cisco NX-OS Release 4.0(2) and later releases, the show snmp-community command displays any SNMP contexts that are mapped to SNMPv2c communities.
This command does not require a license.
Examples
This example shows how to display the SNMP community strings and any associated SNMP contexts:
switch# show snmp communityCommunity Group / Access context--------- -------------- -------testCommunity vdc-operator contextBComm2 network-admincom3 vdc-adminRelated Commands
snmp-server community
Configures SNMP community strings.
snmp-server mib community-map
Maps SNMP community strings to SNMP contexts.
show snmp context
To display the Simple Network Management Protocol (SNMP) context mapping, use the show snmp context command.
show snmp context
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP context mapping:
switch# show snmp context-------------------------------------------------------------------Context [Protocol instance, VRF, Topology]-------------------------------------------------------------------contextB instance1,vrf1,topo1-------------------------------------------------------------------rRelated Commands
show snmp engineID
To display the Simple Network Management Protocol (SNMP) engine ID, use the show snmp engineID command.
show snmp engineID
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP engine ID:
switch(config)# show snmp engineIDLocal SNMP engineID: [Hex] 80000009030005300A0B0C[Dec] 128:000:000:009:003:000:005:048:010:011:012Related Commands
show snmp group
To display the Simple Network Management Protocol (SNMP) groups, use the show snmp group command.
show snmp group
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP groups:
switch(config)# show snmp grouprole: network-admindescription: Predefined network admin role has access to all commandson the switch-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit read-writerole: network-operatordescription: Predefined network operator role has access to all readcommands on the switch-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit readrole: vdc-admindescription: Predefined vdc admin role has access to all commands withina VDC instance-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit read-writerole: vdc-operatordescription: Predefined vdc operator role has access to all read commandswithin a VDC instance-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit readRelated Commands
show snmp host
To display the Simple Network Management Protocol (SNMP) host notification receivers, use the show snmp host command.
show snmp host
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP hosts:
switch(config)# show snmp host-------------------------------------------------------------------Host Port Version Level Type SecName-------------------------------------------------------------------192.0.2.1 33 v1 noauth trap Comm2-------------------------------------------------------------------192.0.2.2 162 v3 auth trap comm3Use VRF: Blue-------------------------------------------------------------------192.0.2.10 162 v3 auth trap testCommunityFilter VRF: Red-------------------------------------------------------------------Related Commands
show snmp sessions
To display the current Simple Network Management Protocol (SNMP) sessions, use the show snmp sessions command.
show snmp sessions
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP sessions:
switch(config)# show snmp sessionsRelated Commands
show snmp source-interface
To display the Simple Network Management Protocol (SNMP) source interface through which notifications are sent, use the show snmp source-interface command.
show snmp source-interface
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP source interface through which notifications are sent:
switch(config)# show snmp source-interface-------------------------------------------------------------------Notification source-interface-------------------------------------------------------------------trap lookback1inform Ethernet1/1-------------------------------------------------------------------switch(config)#Related Commands
snmp-server sourceinterface
Configures an SNMP source interface through which notifications are sent.
show snmp trap
To display the Simple Network Management Protocol (SNMP) notification enable status, use the show snmp trap command.
show snmp trap
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP notification enable status:
switch(config)# show snmp trapTrap type Enabled--------- -------aaa server state-change Nocallhome Noentity fru Yeslicense Yessnmp authentication Novrrp Nolink Nobridge topologychange Nobridge newroot Nostpx inconsistency Nostpx loop-inconsistency Nostpx root-inconsistency NoRelated Commands
show snmp user
To display the Simple Network Management Protocol (SNMP) users, use the show snmp user command.
show snmp user [username [engineID id]]
Syntax Description
Defaults
Displays all users
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP users:
switch(config)# show snmp user______________________________________________________________SNMP USERS______________________________________________________________User Auth Priv(enforce) Groups____ ____ _____________ ______foo md5 aes-128(no) network-operatorvdc-adminnetwork-adminUser3 md5 no network-operatoradmin md5 des(no) network-adminuser1 md5 des(no) vdc-admin______________________________________________________________NOTIFICATION TARGET USERS (configured for sending V3 Inform)______________________________________________________________User Auth Priv____ ____ ____foo md5 no(EngineID 11:22:33:44:55)Related Commands
show sprom
To display the contents of the serial PROM (SPROM) on the device, use the show sprom command.
show sprom {all | backplane bp-number | clock clock-number | cmp | fan fan-number | module slot | powersupply ps-number | stby-sup | sup | xbar xbar-number}
Syntax Description
Defaults
Displays summary information for all processes on the device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
The SPROM on the physical device components contain detail information about the hardware, including the serial number, part number, and revision numbered.
This command does not require a license.
Examples
This example shows how to display SPROM information for all components on the physical device:
switch# show sprom allDISPLAY active supervisor sprom contents:Common block:Block Signature : 0xababBlock Version : 3Block Length : 160Block Checksum : 0x158aEEPROM Size : 65535Block Count : 3FRU Major Type : 0x6004FRU Minor Type : 0x5OEM String : Cisco Systems, IncProduct Number : N7K-SUP1Serial Number : JAB10380101Part Number : 73-10877-03Part Revision : 09Mfg Deviation : 0H/W Version : 0.311Mfg Bits : 0Engineer Use : 0snmpOID : 0.0.0.0.0.0.0.0Power Consump : -247RMA Code : 0-0-0-0CLEI Code : TBDVID : TBD...This example shows how to display SPROM information for a backplane:
switch# show sprom backplane 1DISPLAY backplane sprom contents:Common block:Block Signature : 0xababBlock Version : 3Block Length : 160Block Checksum : 0x147eEEPROM Size : 65535Block Count : 5FRU Major Type : 0x6001FRU Minor Type : 0x0OEM String : Cisco Systems, Inc.Product Number : N7K-C7010Serial Number : TBM11256507Part Number : 73-10900-04Part Revision : 03Mfg Deviation :H/W Version : 0.403Mfg Bits : 0Engineer Use : 0snmpOID : 0.0.0.0.0.0.0.0Power Consump : -247RMA Code : 0-0-0-0CLEI Code :VID :Chassis specific block:Block Signature : 0x6001Block Version : 3Block Length : 39Block Checksum : 0x3bfFeature Bits : 0x0HW Changes Bits : 0x0Stackmib OID : 0MAC Addresses : 00-18-ba-d8-3f-bcNumber of MACs : 128OEM Enterprise : 9OEM MIB Offset : 5MAX Connector Power: 1WWN software-module specific block:Block Signature : 0x6005Block Version : 1Block Length : 0Block Checksum : 0x66wwn usage bits:00 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00License software-module specific block:Block Signature : 0x6006Block Version : 1Block Length : 16Block Checksum : 0x77lic usage bits:00 00 00 00 00 00 00 00Second Serial number specific block:Block Signature : 0x6007Block Version : 1Block Length : 28Block Checksum : 0x302Serial Number : TBM11256507show startup-config cdp
To display the Cisco Discovery Protocol (CDP) startup configuration, use the show startup-config cdp command.
show startup-config cdp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the CDP startup configuration with defaults:
switch(config)# show startup-config cdp all!Command: show startup-config cdp!Time: Tue Feb 2 22:36:26 2010version 5.0(2)logging level cdp 6switch(config)#Related Commands
show startup-config diagnostic
To display startup-configuration diagnostics, use the show startup-config diagnostic command.
show startup-config diagnostic [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the startup-configuration diagnostics:
switch(config)# show startup-config diagnostic all!Command: show startup-config diagnostic all!Time: Tue Jan 26 22:38:22 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)diagnostic bootup level completeswitch(config)#Related Commands
show startup-config cfs
To display information about the Cisco Fabric Services (CFS) startup configuration, use the show startup-config cfs command.
show startup-config cfs [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the CFS startup configuration:
switch(config)# show startup-config cfs!Command: show startup-config cfs!Time: Tue Feb 2 22:40:47 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)switch(config)#Related Commands
cfs distribute
Enables CFS distribution for the device globally.
show cfs status
Displays the CFS distribution status.
show startup-config eem
To display the Embedded Event Manager (EEM) start-up configuration, use the show startup-config eem command.
show startup-config eem
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the Embedded Event Manager (EEM) start-up configuration:
switch# show startup-config eem!Command: show startup-config eem!Time: Tue Feb 2 22:41:25 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)switch#show startup-config monitor
To display information about the startup Ethernet Switched Port Analyzer (SPAN) configuration, use the show startup-config monitor command.
show startup-config monitor
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the startup Ethernet SPAN configuration:
switch(config)# show startup-config monitor!Command: show startup-config monitor!Time: Tue Feb 2 22:42:07 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)logging level monitor 6switch(config)#Related Commands
show monitor
Displays information about an Ethernet switched port analyzer (SPAN).
show running-config monitor
Displays the running configuration to the startup configuration.
show startup-config netflow
To display the startup NetFlow configuration, use the show startup-config netflowcommand.
show startup-config netflow [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the startup NetFlow configuration:
switch# show startup-config netflow!Command: show startup-config monitor!Time: Tue Feb 2 22:42:07 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)logging level monitor 6switch(config)# show startup-config netflow!Command: show startup-config netflow!Time: Tue Feb 2 22:43:13 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)feature netflowflow exporter new_flow_1version 5flow exporter new_flow_2version 9flow exporter testversion 9flow exporter Custom-Flow-Exporter-1version 9option exporter-stats timeout 1200switch#Related Commands
show running-config netflow
Displays information about the NetFlow configuration that is currently running on the switch.
show startup-config ntp
To display the Network Time Protocol (NTP) startup configuration, use the show startup-config ntp command.
show startup-config ntp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the NTP startup configuration:
switch(config)# show startup-config ntp!Command: show startup-config ntp!Time: Tue Feb 2 22:45:37 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)ntp server 192.0.2.10 use-vrf Redntp peer 2001:db8::4101ntp authenticatentp authentication-key 42 md5 dJmhwKzd 7ntp trusted-key 42ntp loggingntp access-group peer NT_GLOBALswitch(config)#Related Commands
show startup-config snmp
To display the startup Simple Network Management Protocol (SNMP) configuration of a system, use the show startup-config snmp command.
show startup-config snmp [all]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the startup SNMP configuration of the system:
switch(config)# show startup-config snmp!Command: show startup-config snmp all!Time: Tue Feb 2 22:46:33 2010!Startup config saved at: Thu Jan 21 08:39:42 2010version 5.0(2)snmp-server aaa-user cache-timeout 3600snmp-server protocol enableno snmp-server globalEnforcePrivsnmp-server tcp-session authsnmp-server user admin network-admin auth md5 0x1dc65f45a9d8e41dbccd76380946d6c3priv 0x1dc65f45a9d8e41dbccd76380946d6c3 localizedkeysnmp-server enable traps ospf rate-limit 10 7snmp-server enable traps ospf foo rate-limit 10 7no snmp-server enable traps bridge topologychangeno snmp-server enable traps bridge newrootno snmp-server enable traps stpx inconsistencyno snmp-server enable traps stpx loop-inconsistencyno snmp-server enable traps stpx root-inconsistencyswitch(config-port-monitor)#Related Commands
show running-config snmp
Displays the running SNMP configuration.
show port-monitor active
Displays active port-monitor policies.
show system cores
To display the core filename, use the show system cores command.
show system cores
Syntax Description
This command has no arguments or keywords.
Defaults
Displays information for all features.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
Use the system cores command to configure the system core filename.
This command does not require a license.
Examples
This example shows how to display destination information for the system core files:
switch# show system coresCores are transferred to slot0:Related Commands
show system error-id
To display the destination information for core files, use the show system error-id command.
show system error-id {error-number | list}
Syntax Description
error-id
Error number. The range is from 0x0 to 0xffffffff.
list
Displays brief information for all the system error messages.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display detailed information for an error message:
switch# show system error-id 0x1Error Facility: (null)Error Description: not enough memoryThis example shows how to display brief information for all the error messages:
switch# show system error-id listCommon errors:0x00000000 (SYSERR_SUCCESS): "success".0x00000001 (SYSERR_NOMEM): "not enough memory".0x00000002 (SYSERR_PSS_ERROR): "error while accessing PSS".0x00000003 (SYSERR_CMI_NO_RESPOSE_PAYLOAD): "no cmi response payload".0x00000004 (SYSERR_CMI_NULL_RECEIVE_BUF): "null cmi receive buffer".0x00000005 (SYSERR_MGMT_ERROR): "unknown error".0x00000006 (SYSERR_MGMT_NO_ENTRY): "entry not present".0x00000007 (SYSERR_MGMT_NO_OBJECT): "object not present"....show system memory-status
To display the memory status information, use the show system memory-status command.
show system memory-status
Syntax Description
This command has no arguments or keywords.
Defaults
Displays information for all features.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the memory status information:
switch# show system memory-statusMemStatus: OKshow system pss shrink status
To display the last Persistent Storage Service (PSS) shrink status, use the show system pss shrink status command.
show system pss shrink status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the last PSS shrink status:
switch(config)# show system pss shrink statusLast pss shrink started on: Tue May 12 08:08:30 2009switch(config)#Related Commands
show system pss shrink status details
Displays the last PSS shrink status details.
show system pss shrink status details
To display details of the last Persistent Storage Service (PSS) shrink status details, use the show system pss shrink status details command.
show system pss shrink status details
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display details of the last PSS shrink status:
switch(config)# show system pss shrink status detailsLast pss shrink started on: Tue May 12 08:08:30 2009VDC 1:Service "aaa" in vdc 1: pss shrink completed successfullyService "cert_enroll" in vdc 1: pss shrink completed successfullyService "ExceptionLog" in vdc 1: pss shrink completed successfullyService "psshelper_gsvc" in vdc 1: pss shrink not needed (defaultcb invoked)Service "platform" in vdc 1: pss shrink completed successfullyService "R2D2_usd" in vdc 1: pss shrink not needed (defaultcb invoked)Service "radius" in vdc 1: pss shrink completed successfullyService "securityd" in vdc 1: pss shrink not needed (defaultcb invoked)Service "tacacs" in vdc 1: pss shrink completed successfullyService "eigrp" in vdc 1: pss shrink request not sentService "isis" in vdc 1: pss shrink not needed (defaultcb invoked)Service "isis_dce" in vdc 1: pss shrink request not sentService "isis_otv" in vdc 1: pss shrink request not sentService "ospf" in vdc 1: pss shrink request not sentService "ospfv3" in vdc 1: pss shrink request not sentService "rip" in vdc 1: pss shrink request not sentService "eigrp" in vdc 1: pss shrink request not sentService "isis" in vdc 1: pss shrink request not sentService "isis_dce" in vdc 1: pss shrink request not sentService "ospf" in vdc 1: pss shrink request not sentService "ospfv3" in vdc 1: pss shrink request not sentService "rip" in vdc 1: pss shrink request not sentService "eigrp" in vdc 1: pss shrink request not sentService "isis" in vdc 1: pss shrink request not sentService "isis_dce" in vdc 1: pss shrink request not sentService "ospf" in vdc 1: pss shrink request not sentService "ospfv3" in vdc 1: pss shrink request not sentService "rip" in vdc 1: pss shrink request not sentService "eigrp" in vdc 1: pss shrink request not sentService "isis" in vdc 1: pss shrink request not sentService "isis_dce" in vdc 1: pss shrink request not sentService "ospf" in vdc 1: pss shrink request not sentService "ospfv3" in vdc 1: pss shrink request not sentService "rip" in vdc 1: pss shrink request not sentService "acllog" in vdc 1: pss shrink completed successfullyService "aclmgr" in vdc 1: pss shrink completed successfullyService "adjmgr" in vdc 1: pss shrink not needed (defaultcb invoked)Service "amt" in vdc 1: pss shrink request not sentService "arbiter" in vdc 1: pss shrink not needed (defaultcb invoked)Service "arp" in vdc 1: pss shrink not needed (defaultcb invoked)Service "ascii-cfg" in vdc 1: pss shrink not needed (defaultcb invoked)Service "babycaesar" in vdc 1: pss shrink not needed (defaultcb invoked)Service "bgp" in vdc 1: pss shrink not needed (defaultcb invoked)Service "bios_daemon" in vdc 1: pss shrink request not sentService "bootup_test" in vdc 1: pss shrink request not sentService "bootvar" in vdc 1: pss shrink not needed (defaultcb invoked)Service "callhome" in vdc 1: pss shrink not needed (defaultcb invoked)Service "capability" in vdc 1: pss shrink completed successfullyService "cardclient" in vdc 1: pss shrink not needed (defaultcb invoked)Service "cdp" in vdc 1: pss shrink completed successfullyService "cfs" in vdc 1: pss shrink completed successfullyService "clis" in vdc 1: pss shrink not needed (defaultcb invoked)Service "cmpproxy" in vdc 1: pss shrink completed successfullyService "confcheck" in vdc 1: pss shrink completed successfully--More--Related Commands
show system reset-reason
To display the reset-reason history for the modules on the device, use the show system reset-reason command.
show system reset-reason [module slot | xbar xbar-number]
Syntax Description
module slot
(Optional) Displays the restart reason for an I/O module or supervisor module.
xbar xbar-number
(Optional) Displays the restart reason for the fabric module.
Defaults
Displays the reset reasons for the supervisor modules.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
You can use this command only in the default virtual device context (VDC).
This command does not require a license.
Examples
This example shows how to display the reset-reason history for the supervisor modules:
switch# show system reset-reason----- reset reason for Supervisor-module 6 (from Supervisor in slot 6) ---1) At 11151 usecs after Fri May 30 14:40:50 2008Reason: Reset Requested by CLI command reloadService:Version: 4.0(2)2) At 171083 usecs after Wed May 28 11:40:49 2008Reason: Reset Requested by CLI command reloadService:Version: 4.0(2)----- reset reason for Supervisor-module 5 (from Supervisor in slot 6) ---1) No timeReason: UnknownService:Version:2) No timeReason: UnknownService:Version:Related Commands
show system redundancy
To display the system redundancy status, use the show system redundancy command.
show system redundancy [ha] status
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the system redundancy status:
switch# show system redundancy statusRedundancy mode---------------administrative: HAoperational: NoneThis supervisor (sup-1)-----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with no standbyOther supervisor (sup-2)------------------------Redundancy state: Not presentswitch#This example shows how to display the virtual device context (VDC) redundancy status:
switch# show system redundancy ha statusVDC No This supervisor Other supervisor------ --------------- ---------------vdc 1 Active with no standby N/Avdc 2 Active with no standby N/Avdc 3 Active with no standby N/Avdc 4 N/A N/Aswitch#Related Commands
show system resources
To display the system resources, use the show system resources command.
show system resources
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the system resources:
switch(config)# show system resourcesLoad average: 1 minute: 0.00 5 minutes: 0.00 15 minutes: 0.0Processes : 520 total, 1 runningCPU states : 0.0% user, 0.5% kernel, 99.5% idleMemory usage: 4135616K total, 1642556K used, 2493060K free1188K buffers, 731988K cacheswitch(config)#Related Commands
show processes cpu
Displays the CPU utilization information for processes on the device.
show system standby manual-boot
To display the status of the system standby manual boot option, use the show system standby manual-boot command.
show system standby manual-boot
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the status of the system standby manual boot option:
switch(config)# show system standby manual-bootsystem standby manual-boot option is enabledswitch(config)#Related Commands
show system uptime
To display the amount of time since the last system upload, use the show system uptime command.
show system uptime
Syntax Description
This command has no arguments or keywords.
Defaults
Displays information for all features.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the amount of time since the last system reload:
switch# show system uptimeSystem start time: Fri May 30 14:46:25 2008System uptime: 16 days, 23 hours, 9 minutes, 22 secondsKernel uptime: 16 days, 23 hours, 13 minutes, 29 secondsActive supervisor uptime: 16 days, 23 hours, 9 minutes, 22 secondsshow tech-support ascii-cfg
To display detailed information about the checkpoint feature, use the show tech-support ascii-cfg command.
show tech-support ascii-cfg
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to show the detailed information about the checkpoint feature:
switch# show tech-support ascii-cfg`show checkpoint summary`-------------------------------------------------------------------------------Name UserName Created at-------------------------------------------------------------------------------stable admin Tue May 27 13:19:24 2008`show checkpoint`-------------------------------------------------------------------------------Name: stableversion 4.0(2)power redundancy-mode combined forcelicense grace-periodfeature vrrpfeature tacacs+feature ospffeature pimfeature pim6feature msdpfeature eigrpfeature ripfeature isisfeature pbrRelated Commands
show tech-support cfs
To display information about the Cisco Fabric Services (CFS) configuration required by technical support, use the show tech-support cfs command.
show tech-support cfs {commands | [name application_name {commands}]}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the CFS configuration required by technical support:
switch# show tech-support cfs`show cfs application`----------------------------------------------Application Enabled Scope----------------------------------------------ntp No Physical-fc-ipstp Yes Physical-ethvpc Yes Physical-ethigmp Yes Physical-ethl2fm Yes Physical-ethrole No Physical-fc-ipradius No Physical-fc-ipcallhome Yes Physical-fc-ipTotal number of entries = 8`show cfs lock``show cfs peers`Physical Fabric-------------------------------------------------------------------------Switch WWN IP Address-------------------------------------------------------------------------20:00:00:22:55:79:a4:c1 172.28.230.85 [Local]switchTotal number of entries = 1`show cfs status`Distribution : EnabledDistribution over IP : Enabled - mode IPv4IPv4 multicast address : 239.255.70.83IPv6 multicast address : ff15::efff:4653Distribution over Ethernet : Disabled`show cfs internal event-history errors`Mon Dec 22 12:24:42 2008 :Sending over network failed, retval ffffffff, errno 113 [No route to host]Msg ID: [6e:00:00:00:c0:e0:ff:bf:0:1]vsan: 4097, IP addr: 0.0.0.0Total number of entries = 8Related Commands
show tech-support session-mgr
To display detailed information about the session manager, which controls configuration sessions, use the show tech-support session-mgr command.
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
Use the show tech-support session-mgr command to gather information about the session manager for troubleshooting purposes. This command displays detailed information about the session manager. The output should be saved to a file and included in any support requests for the session manager.
This command does not require a license.
Examples
This example shows how to save the output of the show tech-support session-mgr command to a file:
switch# show tech-support session-mgr > bootflash:outputRelated Commands
show configuration session
Displays information about the configuration sessions.
show tech-support snmp
To display detailed technical support information for Simple Network Management Protocol (SNMP), use the show tech-support snmp command.
show tech-support snmp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
Use the show tech-support snmp command to gather information about SNMP for troubleshooting purposes. This command displays detailed information about SNMP. The output should be saved to a file and included in any support requests for SNMP.
This command does not require a license.
Examples
This example shows how to save the output of the show tech-support snmp command to a file.
switch# show tech-support snmp > bootflash:outputRelated Commands
show xml server status
To display information about the status of the XML server, use the show xml server status command.
show xml server status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the status of the XML server:
switch(config)# show xml server statusoperational status is enabledmaximum session configured is 8switch(config)#
