Table Of Contents

T Commands

template data timeout

terminal event-manager bypass

test watchdog

transport udp

T Commands

---

This chapter describes the Cisco NX-OS system management commands that begin with the letter T.

template data timeout

To configure the template data timeout parameter for the NetFlow exporter, use the template data timeout command. To remove the template data timeout parameter, use the no form of this command.

template data timeout time

no template data timeout [time]

Syntax Description

time	Time in seconds. The range is from 1 to 86400.

Defaults

None

Command Modes

NetFlow exporter version 9 configuration (config-flow-exporter-version-9)

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure the template data timeout parameter:

switch(config)# flow exporter Netflow-Exporter-1

switch(config-flow-exporter-version-9)# template data timeout 120

This example shows how to remove the template data timeout parameter configuration:

switch(config-flow-exporter)# no template data timeout

switch(config-flow-exporter)#

Related Commands

Command	Description
show flow exporter	Displays information about NetFlow exporters.

terminal event-manager bypass

To allow the CLI commands that match an Embedded Event Manager (EEM) policy to continue to run, use the terminal event-manager bypass command. To prevent such commands from running, use the no form of this command.

terminal event-manager bypass

terminal no event-manager bypass

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to allow the CLI commands that match an EEM policy to continue to run:

switch# terminal event-manager bypass

switch#

This example shows how to prevent the CLI commands that match an EEM policy from running:

switch# terminal no event-manager bypass

switch#

Related Commands

Command	Description
event manager policy	Registers an Embedded Event Manager (EEM) policy with the EEM.

test watchdog

To test the watchdog feature, use the test watchdog command.

test watchdog

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to test the watchdog feature:

switch(config)# test watchdog

Warning: This command will reboot the system if watchdog is functioning properly

.

Do you wish to proceed anyway? (y/n)

Related Commands

Command	Description
system watchdog	Enables the watchdog feature.
system no watchdog	Disables the watchdog feature.

transport udp

To configure a NetFlow exporter to transport over UDP, use the transport udp command. To remove the transport configuration, use the no form of this command.

transport udp port-number

no transport udp [port-number]

Syntax Description

port-number

Destination UDP port number.

Defaults

None

Command Modes

NetFlow exporter configuration (config-flow-exporter)

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure a NetFlow exporter to transport over UDP:

switch(config)# flow exporter Netflow-Exporter-1

switch(config-flow-exporter)# transport udp  200

switch(config-flow-exporter)#

This example shows how to remove the UDP configuration:

switch(config-flow-exporter)# no transport udp 200

switch(config-flow-exporter)#

Related Commands

Command	Description
show flow exporter	Displays information about NetFlow exporters.