Table Of Contents

Show Commands

show forwarding distribution ip igmp snooping

show forwarding distribution ipv6 multicast route

show forwarding distribution multicast

show forwarding distribution multicast client

show forwarding distribution multicast outgoing-interface-list

show forwarding distribution multicast route

show forwarding ipv6 multicast route

show forwarding multicast outgoing-interface-list

show forwarding multicast route

show ip igmp event-history

show ip igmp groups

show ip igmp interface

show ip igmp local-groups

show ip igmp route

show ip igmp snooping

show ip igmp snooping event-history

show ip igmp snooping explicit-tracking

show ip igmp snooping groups

show ip igmp snooping mrouter

show ip igmp snooping querier

show ip igmp snooping statistics

show ip mroute

show ip mroute summary

show ip msdp count

show ip msdp event-history

show ip msdp mesh-group

show ip msdp peer

show ip msdp policy statistics sa-policy

show ip msdp route

show ip msdp rpf

show ip msdp sa-cache

show ip msdp sources

show ip msdp summary

show ip netstack mroute

show ip pim df

show ip pim event-history

show ip pim group-range

show ip pim interface

show ip pim neighbor

show ip pim oif-list

show ip pim policy statistics auto-rp

show ip pim policy statistics bsr

show ip pim policy statistics jp-policy

show ip pim policy statistics neighbor-policy

show ip pim policy statistics register-policy

show ip pim route

show ip pim rp

show ip pim rp-hash

show ip pim statistics

show ip pim vrf

show ipv6 mld groups

show ipv6 mld local-groups

show ipv6 mroute

show ipv6 mroute summary

show ipv6 pim df

show ipv6 pim event-history

show ipv6 pim group-range

show ipv6 pim interface

show ipv6 pim neighbor

show ipv6 pim oif-list

show ipv6 pim policy statistics jp-policy

show ipv6 pim policy statistics neighbor-policy

show ipv6 pim route

show ipv6 pim rp

show ipv6 pim rp-hash

show ipv6 pim statistics

show ipv6 pim vrf

show routing ip multicast event-history

show routing ipv6 multicast

show routing ipv6 multicast clients

show routing ipv6 multicast event-history

show routing multicast

show routing multicast clients

show running-config igmp

show running-config msdp

show running-config pim

show running-config pim6

show startup-config igmp

show startup-config msdp

show startup-config pim

show startup-config pim6

Show Commands

---

This chapter describes the Cisco NX-OS multicast routing show commands.

show forwarding distribution ip igmp snooping

To display information about Layer 2 IGMP snooping multicast FIB distribution, use the show forwarding distribution ip igmp snooping command.

show forwarding distribution ip igmp snooping [vlan vlan-id [group group-addr [source source-addr]]]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
group group-addr	(Optional) Specifes a group address.
source source-addr	(Optional) Specifies a source address.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about Layer 2 IGMP snooping multicast FIB distribution:

switch(config)# show forwarding distribution ip igmp snooping

Vlan: 1, Group: 0.0.0.0, Source: 0.0.0.0

  Outgoing Interface List Index: 65535

  Reference Count: 5

  Platform Index: 0x0

  Number of Outgoing Interfaces: 0

Vlan: 3, Group: 0.0.0.0, Source: 0.0.0.0

  Outgoing Interface List Index: 65535

  Reference Count: 5

  Platform Index: 0x0

  Number of Outgoing Interfaces: 0

Vlan: 13, Group: 0.0.0.0, Source: 0.0.0.0

  Outgoing Interface List Index: 65535

  Reference Count: 5

  Platform Index: 0x0

  Number of Outgoing Interfaces: 0

Vlan: 200, Group: 0.0.0.0, Source: 0.0.0.0

  Outgoing Interface List Index: 65535

  Reference Count: 5

  Platform Index: 0x0

  Number of Outgoing Interfaces: 0

Vlan: 1001, Group: 0.0.0.0, Source: 0.0.0.0

  Outgoing Interface List Index: 65535

  Reference Count: 5

  Platform Index: 0x0

  Number of Outgoing Interfaces: 0

show forwarding distribution ipv6 multicast route

To display information about the multicast IPv6 FIB routes, use the show forwarding distribution ipv6 multicast route command.

show forwarding distribution ipv6 multicast route [table table_id | vrf vrf-name] [group [source] | summary]

Syntax Description

table table_id	(Optional) Specifies a table ID. The range is from 0x0 to 0xffffffff.
vrf vrf-name	(Optional) Specifies a virtual routing and forwarding (VRF) name.
group	(Optional) IPv6 group address.
source	(Optional) IPv6 source address.
summary	(Optional) Specifies route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast IPv6 FIB routes:

switch(config)# show forwarding distribution ipv6 multicast route

IPv6 Multicast Routing table table-id:0x80000001

Total number of groups: 5

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF Fail

   P = Punt to supervisor

  (*, ff00::/8), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff01::/16), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff02::/16), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff11::/16), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff12::/16), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

switch#

show forwarding distribution multicast

To display information about multicast distribution messages, use the show forwarding distribution multicast command.

show forwarding distribution multicast [messages]

Syntax Description

messages

(Optional) Displays message information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about multicast distribution messages:

switch(config)# show forwarding distribution multicast

Number of Multicast FIB Processes Active: 2

Slot     FIB State

   2        ACTIVE

   7        ACTIVE

switch#

show forwarding distribution multicast client

To display information about the multicast FIB distribution client, use the show forwarding distribution multicast client command.

show forwarding distribution multicast client

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast distribution client:

switch(config)# show forwarding distribution multicast client

Number of Clients Registered: 3

Client-name  Client-id  Shared Memory Name

m6rib        1          m6rib-mfdm

mrib         2          mrib-mfdm

igmp         3          N/A

switch# 

show forwarding distribution multicast outgoing-interface-list

To display information about the multicast outgoing interface (OIF) list, use the show forwarding distribution multicast outgoing-interface-list command.

show forwarding distribution multicast outgoing-interface-list {L2 | L3} [index]

Syntax Description

L2	Specifies the Layer 2 OIF list.
L3	Specifies the Layer 3 OIF list.
index	(Optional) OIF list index.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast OIF list for Layer 3:

switch(config)# show forwarding distribution multicast outgoing-interface-list L3

  Outgoing Interface List Index: 1

  Reference Count: 1

  Platform Index: 0x7ffe

  Number of Outgoing Interfaces: 1

    mgmt0

switch#

show forwarding distribution multicast route

To display information about the multicast FIB distribution routes, use the show forwarding distribution multicast route command.

show forwarding distribution [ip | ipv4] multicast route [table id | vrf vrf_name] [[group {group-addr [mask] | group-prefix}] [source {source-addr [source-mask] | source-prefix}] | summary]

Syntax Description

ip	(Optional) Specifies IPV4 information.
ipv4	(Optional) Specifies IPV4 information.
table id	(Optional) Specifies the multicast routing table ID. The range is from 0 to 2147483647.
vrf vrf_name	(Optional) Specifies a virtual routing and forwarding (VRF) name.
group	(Optional) Specifies IPv4 multicast group.
group-addr	IPv4 multicast group address.
mask	(Optional) Mask for the group address.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies IPv4 multicast source.
source-addr	IPv4 source address.
source-mask	(Optional) Mask for the group address.
source-prefix	(Optional) IPv4 multicast source prefix.
summary	(Optional) Displays the route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about all the multicast FIB distribution routes:

switch(config)# show forwarding distribution multicast route

IPv4 Multicast Routing Table for table-id: 1

Total number of groups: 4

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF Fail

   P = Punt to supervisor

  (*, 224.0.0.0/4), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.0.0/24), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.39/32), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.40/32), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

switch#

show forwarding ipv6 multicast route

To display information about the IPv6 multicast routes, use the show forwarding ipv6 multicast route command.

show forwarding [vrf {vrf-name | all}] ipv6 multicast route {[group {group | group-addr} | source {source | source-addr} | module num | vrf {vrf-name | all}] | summary [module num | vrf {vrf-name | all}]}

Syntax Description

vrf	(Optional) Displays routes for a specific virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Displays information for all VRFs.
group	(Optional) Specifies multicast IPv6 group address.
group	Multicast IPv6 group address with prefix.
group-addr	Multicast IPv6 group address.
source	Specifies multicast IPv6 source address.
source	Multicast IPv6 source address with prefix.
source-addr	Multicast IPv6 source address.
module num	(Optional) Specifies module number.
summary	Displays route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Added the group-addr and source-addr arguments.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv6 multicast routes:

switch(config)# show forwarding ipv6 multicast route 

IPv6 Multicast Routing table table-id:0x80000001

Total number of groups: 0

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF failure

   P = Punt to Supervisor

  (*, ff00::/8), RPF Interface: NULL, flags: DW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff01::/16), RPF Interface: NULL, flags: DW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff02::/16), RPF Interface: NULL, flags: CPW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff11::/16), RPF Interface: NULL, flags: DW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, ff12::/16), RPF Interface: NULL, flags: CPW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

switch(config)# 

show forwarding multicast outgoing-interface-list

To display information about the multicast outgoing interface (OIF) list, use the show forwarding multicast outgoing-interface-list command.

show forwarding multicast outgoing-interface-list [module num] [index]

Syntax Description

module num	(Optional) Specifies the module number.
index	(Optional) OIF list index.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast outgoing interface (OIF) list:

switch(config)# show forwarding multicast outgoing-interface-list

  Outgoing Interface List Index: 65535

  Reference Count: 9

switch(config)# 

show forwarding multicast route

To display information about the IPv4 multicast routes, use the show forwarding multicast route command.

show forwarding [vrf {vrf-name | all}] [ip | ipv4] multicast route {[group {group-addr [group-mask] | group-prefix} | source {source-addr [source-mask] | source-prefix} | module num | vrf {vrf-name | all}]+ | summary [module num | vrf {vrf-name | all}]}

Syntax Description

vrf	(Optional) Displays information for a specified virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Displays information for all VRFs.
ip	(Optional) Specifies IPv4.
ipv4	(Optional) Specifies IPv4.
group	(Optional) Specifies IPv4 multicast group address.
group-addr	IPv4 multicast group address.
group-mask	(Optional) IPv4 multicast group address mask.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies IPv4 multicast source address.
source-addr	IPv4 multicast source address.
source-mask	(Optional) IPv4 multicast source address mask.
source-prefix	(Optional) IPv4 multicast source prefix.
module num	(Optional) Specifies the module number.
summary	Displays route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv4 multicast routes:

switch(config)# show forwarding multicast route 

IPv4 Multicast Routing table table-id:1

Total number of groups: 0

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF failure

   P = Punt to Supervisor

   W = Wildcard

  (*, 224.0.0.0/4), RPF Interface: NULL, flags: DW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.0.0/24), RPF Interface: NULL, flags: CPW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.39/32), RPF Interface: NULL, flags: CPW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.40/32), RPF Interface: NULL, flags: CPW

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

show ip igmp event-history

To display information in the IGMP event history buffers, use the show ip igmp event-history command.

show ip igmp event-history {clis | debugs | errors | events | ha | igmp-internal | msgs | mtrace | policy | statistics | vrf}

Syntax Description||

cli	Displays events of type CLI.
debugs	Displays events of type debug.
errors	Displays events of type error.
events	Displays events of type event.
ha	Displays events of type HA.
igmp-internal	Displays events of type IGMP internal.
msgs	Displays events of type msg.
mtrace	Displays events of type mtrace.
policy	Displays events of type policy.
statistics	Displays events of type statistics.
vrf	Displays events of type VRF.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP HA event history buffer:

switch(config)# show ip igmp event-history ha

 ha events for IGMP process

1) Event:E_DEBUG, length:44, at 423337 usecs after Mon Dec 22 12:24:49 2008

    [121] : Updated entry in Route count database

2) Event:E_DEBUG, length:45, at 423072 usecs after Mon Dec 22 12:24:49 2008

    [121] : Updating entry in Route count database

3) Event:E_DEBUG, length:49, at 943183 usecs after Mon Dec 22 12:24:41 2008

    [121] : Recovered all route count entries from PSS

4) Event:E_DEBUG, length:38, at 943133 usecs after Mon Dec 22 12:24:41 2008

    [121] : Recovering Route count database

5) Event:E_DEBUG, length:55, at 943124 usecs after Mon Dec 22 12:24:41 2008

    [121] : Attempting IGMP SNOOP database stateful recovery

switch(config)#

Related Commands

Command	Description
clear ip igmp event-history	Clears the contents of the IGMP event history buffers.
ip igmp event-history	Configures the size of IGMP event history buffers.

show ip igmp groups

To display information about IGMP-attached group membership, use the show ip igmp groups command.

show ip igmp groups [{source [group]} | {group [source]}] [if-type if-number] [vrf {vrf-name | all}]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of the single group to display.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

The show ip igmp route command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch(config)# show ip igmp groups

IGMP Connected Group Membership for Context "default" - 2 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address      Type Interface            Uptime    Expires   Last Reporter

224.1.1.1          L    GigabitEthernet2/8   00:00:04  00:04:15  1.0.8.3

224.1.1.2          L    GigabitEthernet2/8   00:00:02  00:04:17  1.0.8.3

switch(config)# 

Related Commands

Command	Description
show ip igmp route	Displays information about the IGMP-attached group membership.

show ip igmp interface

To display information about IGMP on interfaces, use the show ip igmp interface command.

show ip igmp interface if-type if-number

show ip igmp interface [brief] [vrf {vrf-name | all}]

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
brief	(Optional) Displays one line status per interface.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Changed output to include vPC information when IGMP is in vPC mode.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP on an interface (if IGMP is not in vPC mode, the vPC information is not displayed):

switch(config)# show ip igmp interface vlan 5

IGMP Interfaces for VRF "default"

Vlan5, Interface status: protocol-up/link-up/admin-up

  IP address: 2.4.0.4, IP subnet: 2.4.0.0/24

  Active querier: 2.4.0.4, version: 2, next query sent in: 00:01:02

  Membership count: 0

  Old Membership count 0

  IGMP version: 2, host version: 2

  IGMP query interval: 125 secs, configured value: 125 secs

  IGMP max response time: 10 secs, configured value: 10 secs

  IGMP startup query interval: 31 secs, configured value: 31 secs

  IGMP startup query count: 2

  IGMP last member mrt: 1 secs

  IGMP last member query count: 2

  IGMP group timeout: 260 secs, configured value: 260 secs

  IGMP querier timeout: 255 secs, configured value: 255 secs

  IGMP unsolicited report interval: 10 secs

  IGMP robustness variable: 2, configured value: 2

  IGMP reporting for link-local groups: disabled

  IGMP interface enable refcount: 1

  IGMP Report Policy: None

  IGMP State Limit: None

  IGMP interface statistics:

    General (sent/received):

      v1-reports: 0/0

      v2-queries: 574/574, v2-reports: 0/3, v2-leaves: 0/3

      v3-queries: 0/0, v3-reports: 0/0

    Errors:

      Checksum errors: 0, Packet length errors: 0

      Packets with Local IP as source: 2, Source subnet check failures: 0

      Query from non-querier:0

      Report version mismatch: 0, Query version mismatch: 0

      Unknown IGMP message type: 0

      Invalid v1 reports: 0, Invalid v2 reports: 0, Invalid v3 reports: 0

    Packets dropped due to router-alert check: 0

  Interface PIM DR: vPC Peer

  Interface vPC CFS statistics:

    DR queries sent: 2

    DR queries rcvd: 0

    DR queries fail: 0

    DR updates sent: 4

    DR updates rcvd: 0

    DR updates fail: 0

switch(config)# 

This example shows how to display information about IGMP on an interface in a brief format:

switch(config)# show ip igmp interface brief

IGMP Interfaces for VRF "default", count: 2

Interface            IP Address      IGMP Querier    Membership  Version

                                                     Count

Ethernet2/11         192.168.1.222   0.0.0.0         0           v2

Ethernet2/12         unassigned      0.0.0.0         0           v2

switch(config)#

show ip igmp local-groups

To display information about IGMP local groups, use the show ip igmp local-groups command.

show ip igmp local-groups [if-type if-number] [vrf {vrf-name | all}]

Syntax Description

if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP local groups:

switch(config)# show ip igmp local-groups

IGMP Locally Joined Group Membership for VRF "default"

Group Address    Source Address   Type     Interface   Last Reported

230.0.0.0        *                Static   Eth2/11     4d04h

224.0.1.39       *                Local    Eth2/11     4d04h

224.0.1.40       *                Local    Eth2/11     4d04h

switch(config)# 

show ip igmp route

To display information about the IGMP-attached group membership, use the show ip igmp route command.

show ip igmp route [{source [group]} | {group [source]}] [if-type if-number] [vrf {vrf-name | all}]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of single group to display.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

The show ip igmp groups command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch(config)# show ip igmp route

IGMP Connected Group Membership for Context "default" - 2 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address      Type Interface            Uptime    Expires   Last Reporter

224.1.1.1          L    GigabitEthernet2/8   00:00:04  00:04:15  1.0.8.3

224.1.1.2          L    GigabitEthernet2/8   00:00:02  00:04:17  1.0.8.3

switch(config)# 

Related Commands

Command	Description
show ip igmp groups	Displays information about the IGMP-attached group membership.

show ip igmp snooping

To display information about IGMP snooping, use the show ip igmp snooping command.

show ip igmp snooping [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093. The default is all VLANs.

Defaults

Displays all VLANs.

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping for a VLAN:

switch(config)# show ip igmp snooping vlan 1

IGMP Snooping information for vlan 1

  IGMP snooping enabled

  IGMP querier none

  Switch-querier disabled

  Explicit tracking enabled

  Fast leave enabled

  Report suppression enabled

  Router port detection using PIM Hellos, IGMP Queries

  Number of router-ports: 0

  Number of groups: 0

switch(config)#

show ip igmp snooping event-history

To display information in the IGMP snooping event history buffers, use the show ip igmp snooping event-history command.

show ip igmp snooping event-history {vpc | igmp-snoop-internal | mfdm | mfdm-sum | vlan | vlan-events}

Syntax Description||

vpc	Displays event history buffer of type virtual port channel (vPC).
igmp-snoop- internal	Displays event history buffer of type IGMP snooping internal.
mfdm	Displays event history buffer of type multicast FIB distribution (MFDM).
mfdm-sum	Displays event history buffer of type MFDM sum.
vlan	Displays event history buffer of type VLAN.
vlan-events	Displays event history buffer of type VLAN events.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP snooping VLAN event history buffer:

switch(config)# show ip igmp snooping event-history vlan

 vlan Events for IGMP snoopprocess

switch(config)#

Related Commands

Command	Description
ip igmp snooping event-history	Configures the size of the IGMP snooping event history buffers.
clear ip igmp snooping event-history	Clears information in the IGMP snooping event history buffers.

show ip igmp snooping explicit-tracking

To display information about explicit tracking for IGMP snooping, use the show ip igmp snooping explicit-tracking command.

show ip igmp snooping explicit-tracking [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.2(2)	This command was changed to make the vlan argument optional.

Usage Guidelines

When you use this command without the optional vlan argument, the system displays information for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about explicit tracking for IGMP snooping for VLAN 33:

switch(config)# show ip igmp snooping explicit-tracking vlan 33

IGMPv3 Snooping Explicit-tracking information

Source/Group            Intf      Reporter        Uptime    Last-Join Expires

1.1.1.1 232.1.1.1       Eth2/1    3.3.3.3         00:01:33  00:04:27  00:01:44

switch(config)#

show ip igmp snooping groups

To display information about group membership for IGMP snooping, use the show ip igmp snooping groups command.

show ip igmp snooping groups [{source [group]} | {group [source]}] [vlan vlan-id] [detail]

Syntax Description

source	(Optional) Source address for route.
group	(Optional) Group address for route.
vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
detail	(Optional) Displays detailed information for the group.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Arguments source and group were added.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about group membership for IGMP snooping:

switch(config)# show ip igmp snooping groups

Type: S - Static, D - Dynamic, R - Router port

Vlan  Group Address      Ver  Type  Port list

33    225.1.1.1          v3   S     Eth2/1 

switch(config)#

show ip igmp snooping mrouter

To display the multicast routers detected by IGMP snooping, use the show ip igmp snooping mrouter command.

show ip igmp snooping mrouter [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the multicast routers detected by IGMP snooping:

switch(config)# show ip igmp snooping mrouter

Type: S - Static, D - Dynamic, V - vPC Peer Link

Vlan  Router-port   Type     Uptime      Expires

1     Po88          SV       00:00:51    never

2     Po88          SV       00:00:51    never

3     Po88          SV       00:00:51    never

4     Po88          SV       00:00:51    never

5     Vlan5           D      18:02:38    00:04:40

switch(config)#

show ip igmp snooping querier

To display information about IGMP snooping queriers, use the show ip igmp snooping querier command.

show ip igmp snooping querier [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping queriers:

switch(config)# show ip igmp snooping querier

Vlan  IP Address       Version   Port

1     172.20.50.11     v3        fa2/1

2     172.20.40.20     v2        Router

switch(config)#

show ip igmp snooping statistics

To display information about IGMP snooping statistics, use the show ip igmp snooping statistics command.

show ip igmp snooping statistics [vlan vlan-id | global]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
global	(Optional) Specifies the global statistics.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.
4.2(1)	Enhanced output for vPC information.
4.2(2)	Changed command to make the vlan argument optional and to introduce the optional global argument.

Usage Guidelines

When you use this command without any options, the system prints statistics for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping statistics for VLAN 1:

switch(config)# show ip igmp snooping statistics vlan 1

Global IGMP snooping statistics:

Packets received: 78

  Packet errors: 0

  Packets for non-snooped vlans : 0

  Packets flooded: 41

  vPC PIM DR queries sent: 0

  vPC PIM DR queries rcvd: 0

  vPC PIM DR queries fail: 0

  vPC PIM DR updates sent: 4

  vPC PIM DR updates rcvd: 0

  vPC PIM DR updates fail: 0

  vPC CFS send fail: 0

  vPC CFS message response sent: 13

  vPC CFS message response rcvd: 16

  vPC CFS message response fail: 0

  vPC CFS message response fail peer-link down: 0

  vPC CFS unreliable message sent: 35

  vPC CFS unreliable message rcvd: 37

  vPC CFS unreliable message fail: 0

  vPC CFS reliable message sent: 16

  vPC CFS reliable message rcvd: 13

  vPC CFS reliable message fail: 0

  STP TCN messages rcvd: 22

  IM api failed: 0

VLAN 2 IGMP snooping statistics, last reset: never

  Packets received: 29

  IGMPv1 reports received: 0

  IGMPv2 reports received: 13

  IGMPv3 reports received: 0

  IGMPv1 queries received: 0

  IGMPv2 queries received: 14

  IGMPv3 queries received: 0

  IGMPv2 leaves received: 0

  PIM Hellos received: 0

  Invalid reports received: 0

  Invalid queries received: 0

  IGMPv1 reports suppressed: 0

  IGMPv2 reports suppressed: 0

  IGMPv2 leaves suppressed: 0

  IGMPv3 group records suppressed: 0

  Queries originated: 0

  IGMPv2 proxy-reports originated: 0

  IGMPv2 proxy-leaves originated: 0

  IGMPv3 proxy-reports originated: 0

  Packets sent to routers: 13

  STP TCN received: 9

  Report version mismatch: 0

  Unknown packets received: 0

  vPC Peer Link CFS packet statistics:

      IGMP packets (sent/recv/fail): 11/16/0

      MRD updates (sent/recv/fail): 0/0/0

show ip mroute

To display information about IPv4 multicast routes, use the show ip mroute command.

show ip mroute {group | {source group} | {group [source]}} [summary [software-forwarded]] [vrf {vrf-name | all}]

Syntax Description

group	Group address for route.
source	Source address for route.
summary	(Optional) Displays route counts and packet rates.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about multicast routes:

switch(config)# show ip mroute

IP Multicast Routing Table for VRF "default"

(*, 224.1.1.1/32), uptime: 13:00:28, igmp ip pim

  Incoming interface: Loopback1 (iod: 3), RPF nbr: 2.2.2.2

  Outgoing interface list: (count: 1)

    GigEther2/0/1 (iod 4), uptime: 13:00:28, igmp

(*, 226.1.1.1/32), uptime: 13:00:32, igmp ip pim

  Incoming interface: Loopback1 (iod: 3), RPF nbr: 2.2.2.2

  Outgoing interface list: (count: 1)

    GigEther2/0/1 (iod 4), uptime: 13:00:32, igmp

(*, 228.2.2.2/32), uptime: 13:00:27, igmp ip pim

  Incoming interface: Loopback1 (iod: 3), RPF nbr: 2.2.2.2

  Outgoing interface list: (count: 1)

    GigEther2/0/1 (iod 4), uptime: 13:00:27, igmp

(*, 232.0.0.0/8), uptime: 13:01:27, pim ip

  Incoming interface: Null (iod: 0), RPF nbr: 0.0.0.0

  Outgoing interface list: (count: 0)

switch(config)#

The display specifies the interface establised for each one and shows the router owners. In the case of the first paragraph in the display, the route owner is igmp ip pim. iod is an internal representation the device uses for the interface.

Related Commands

Command	Description
show ip mroute summary	Displays summary information about IPv4 multicast routes.

show ip mroute summary

To display summary information about IPv4 multicast routes, use the show ip mroute summary command.

show ip mroute summary [count | software-forwarded]] [vrf {vrf-name | all}]

show ip mroute {group] summary [software-forwarded] [vrf {vrf-name | all}]

Syntax Description

count	(Optional) Displays only route counts.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
group	Specifies a group address for a route.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display summary information about multicast routes:

switch(config)# show ip mroute summary

IP Multicast Routing Table for VRF "default"

Total number of routes: 6

Total number of (*,G) routes: 4

Total number of (S,G) routes: 1

Total number of (*,G-prefix) routes: 1

Group count: 4, rough average sources per group: 0.2

Group: 225.0.0.1/32, Source count: 0

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     1

Group: 225.0.1.1/32, Source count: 0

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     1

Group: 225.1.1.1/32, Source count: 1

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     4

2.1.1.2           0             0               0     0         0 bps     4

Group: 226.1.1.1/32, Source count: 0

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     1

Group: 232.0.0.0/8, Source count: 0

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     0

0 bps     0

switch(config)#

Related Commands

Command	Description
show ip mroute	Displays information about IPv4 multicast routes.

show ip msdp count

To display information about Multicast Source Discovery Protocol (MSDP) counts, use the show ip msdp count command.

show ip msdp count [asn] [vrf {vrf-name | all}]

Syntax Description

asn	(Optional) Autonomous systems (AS) number.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display MSDP counts:

switch(config)# show ip msdp count

	SA State per ASN, context "default" - 2134 total entries

  	  <asn>: <(S,G) count>/<group count>

      3:     5/4         8:     4/4         9:     7/6        12:     1/1     

     14:    18/14       17:     4/3        18:    11/3        25:   331/290   

     26:    10/6        27:     1/1        32:     4/4        38:     8/5     

     52:    11/2        55:    13/2        59:    12/9        70:     6/4     

     73:    10/10       81:    30/13       87:     1/1       103:    11/10    

    109:    46/23      111:     1/1       131:    21/3       137:     8/8     

    159:     9/6       160:     2/2       194:     2/1       195:     2/1     

    217:     1/1       224:    24/13      225:     1/1       237:    38/31    

    271:     8/7       291:     1/1       292:     2/2       293:     5/4     

    297:     6/6       549:     3/2       553:     1/1       559:    23/18    

    668:     2/1       680:    26/21      683:    16/10      704:    18/15    

    766:    18/17      776:     2/2       786:   123/49      818:     2/2     

   1103:    46/37     1161:     2/2      1224:    10/8      1239:     9/9     

   1273:     1/1      1312:     1/1      1657:     6/6      1706:     7/6     

   1725:     1/1      1739:     3/3      1741:    11/11     1742:     6/5     

   1835:     1/1      1851:     2/1      1935:     1/1      1998:     6/6     

   2055:     7/6      2107:     2/2      2152:     7/5      2200:    46/29    

   2259:   168/4      2381:     8/4      2422:     5/5      2594:    25/25    

   2607:    64/59     2611:    45/37     2637:     5/4      2701:     1/1     

   2852:   117/16     2914:     2/2      3323:     2/2      3582:    27/24    

   3676:     7/3      3685:     9/8      3851:     1/1      3912:     5/3     

   3948:     1/1      3999:     6/4      4130:     4/4      4201:     5/4     

   4385:     9/5      5050:     1/1      5408:     4/3      5520:     3/3     

   5640:    26/6      5661:    14/10     5664:     3/3      5719:     2/2     

   5739:     1/1      6192:     5/2      6200:     2/2      6263:     8/5     

   6360:     3/1      6366:     8/6      6481:    15/12     6509:    31/9     

   7082:     4/1      7212:     4/3      7377:    10/9      7539:    63/37    

   7570:     3/3      7571:     1/1      7572:     1/1      7575:    20/11    

   7610:     1/1      7660:     1/1      7774:     2/1      7896:     2/2     

   8071:     5/3      8111:    22/22     9112:     5/2      9270:     2/1     

   9821:     1/1     10546:     2/2     10764:     1/1     10886:     2/2     

  11050:     2/2     11078:     2/1     11279:    13/3     11537:     8/3     

  11546:     1/1     11808:     1/1     12005:     2/2     12173:     1/1     

  13476:     1/1     13501:     5/4     14077:     3/3     15474:     1/1     

  15725:     1/1     16430:     2/1     16517:     2/2     17055:     3/2     

  18047:    14/14    18062:   111/41    18297:     2/2     20965:    24/1     

  22168:     2/2     23366:     6/2     23504:     5/1     23719:    11/8     

  24433:     6/3     24434:     5/2     24437:     1/1     25656:     1/1     

  25689:     3/3     26002:     5/3     26367:     1/1     26934:     3/3     

  26971:     1/1     29825:     1/1     32666:     5/5     65028:     1/1    

switch(config)#

show ip msdp event-history

To display information in the Multicast Source Discovery Protocol (MSDP) event history buffers, use the show ip msdp event-history command.

show ip msdp event-history {errors | msgs | statistics}

Syntax Description||

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the MSDP msgs event history buffer:

switch(config)# show ip msdp event-history msgs

Msg events for MSDP Process

1) Event:E_DEBUG, length:38, at 198828 usecs after Wed Jan  7 17:24:45 2009

    [100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 197333 usecs after Wed Jan  7 17:24:45 2009

    [100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:77, at 197327 usecs after Wed Jan  7 17:24:45 2009

    [100] : comp-mts-rx opc - from sap 27315 cmd msdp_show_internal_event_hist_cmd

4) Event:E_DEBUG, length:35, at 277809 usecs after Wed Jan  7 17:24:40 2009

    [100] : nvdb: terminate transaction

5) Event:E_DEBUG, length:60, at 277696 usecs after Wed Jan  7 17:24:40 2009

    [100] : nvdb: msdp_show_internal_event_hist_cmd returned 0x0

6) Event:E_DEBUG, length:38, at 277243 usecs after Wed Jan  7 17:24:40 2009

    [100] : nvdb: transient thread created

7) Event:E_DEBUG, length:38, at 275631 usecs after Wed Jan  7 17:24:40 2009

    [100] : nvdb: create transcient thread

8) Event:E_DEBUG, length:77, at 275625 usecs after Wed Jan  7 17:24:40 2009

    [100] : comp-mts-rx opc - from sap 27315 cmd msdp_show_internal_event_hist_cmd

9) Event:E_DEBUG, length:47, at 93136 usecs after Wed Jan  7 17:24:32 2009

    [100] : nvdb: _cli_send_my_command returned 0x0

switch(config)#

Related Commands

Command	Description
clear ip msdp event-history	Clears the contents of the MSDP event history buffers.
ip msdp event-history	Configures the size of MSDP event history buffers.

show ip msdp mesh-group

To display information about Multicast Source Discovery Protocol (MSDP) mesh groups, use the show ip msdp mesh-group command.

show ip msdp mesh-group [mesh-group] [vrf {vrf-name | all}]

Syntax Description

mesh-group	(Optional) Mesh group name.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MSDP mesh groups:

switch(config)# show ip msdp mesh-group

MSDP Mesh-Group Membership for VRF "default"

Mesh-group: my_mesh_group

  Peer: 192.168.1.10, AS: 8, description: engineering peer

show ip msdp peer

To display information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp peer command.

show ip msdp peer [peer-address] [vrf {vrf-name | all}]

Syntax Description

peer-address	(Optional) IP address of an MSDP peer.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MSDP peers:

switch(config)# show ip msdp peer

MSDP peer 192.168.1.10 for VRF "default"

AS 8, local address: 192.168.1.222 (Ethernet2/11)

  Description: engineering peer

  Connection status: Listening

    Uptime(Downtime): 01:14:30

    Last reset reason: Connect source interface address changed

    Password: not set

  Keepalive Interval: 10 sec

  Keepalive Timeout: 20 sec

  Reconnection Interval: 20 sec

  Policies:

    SA in: my_incoming_sa_policy, SA out: none

    SA limit: unlimited

  Member of mesh-group: my_mesh_group

  Statistics (in/out):

    Last messaged received: never

    SAs: 0/0, SA-Requests: 0/0, SA-Responses: 0/0

    Keepalives: 0/0, Notifications: 0/0

switch(config)#

show ip msdp policy statistics sa-policy

To display information about Multicast Source Discovery Protocol (MSDP) Source-Active (SA) policies, use the show ip msdp policy statistics sa-policy command.

show ip msdp policy statistics sa-policy peer-address {in | out} [vrf {vrf-name}]

Syntax Description

peer-address	IP address of the MSDP peer for the SA policy.
in	Specifies the input policy.
out	Specifies the output policy.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MSDP SA policies:

switch(config)# show ip msdp policy statistics sa-policy 192.168.1.10 in

C: No. of comparisions, M: No. of matches

route-map rmap1 permit 10

  match ip multicast group 225.1.1.0/24                      C: 0      M: 0     

Total accept count for policy: 12

Total reject count for policy: 21    

switch(config)# 

show ip msdp route

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp route command.

show ip msdp route [{source [group]} | {group [source]}] [asn] [peer peer] [detail] [vrf {vrf-name | all}]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) AS number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

The show ip msdp sa-cache command is an alternative form of this command.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp route

MSDP SA Route Cache for Context "default" - 2138 entries

Source           Group            RP               ASN    Uptime   

24.124.36.130    224.0.1.1        144.228.240.250  1239   17:35:19 

64.104.160.29    224.0.1.1        204.69.199.17    109    17:35:19 

128.59.21.232    224.0.1.1        128.59.0.51      14     03:33:59 

128.117.37.217   224.0.1.1        128.117.243.9    194    04:07:17 

128.117.37.220   224.0.1.1        128.117.243.9    194    04:08:45 

129.49.88.9      224.0.1.1        199.109.44.1     5719   17:34:48 

130.18.14.12     224.0.1.1        192.208.151.9    10546  17:35:19 

130.37.20.4      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.20.5      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.20.7      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.64.252    224.0.1.1        145.145.255.6    1103   17:35:21 

130.88.20.1      224.0.1.1        194.66.25.224    786    17:35:19 

130.159.54.4     224.0.1.1        194.81.62.54     786    17:35:19 

130.159.228.48   224.0.1.1        194.81.62.54     786    17:35:19 

130.159.248.12   224.0.1.1        194.81.62.54     786    17:35:19 

132.234.1.1      224.0.1.1        132.234.251.232  7575   13:40:17 

134.174.190.41   224.0.1.1        192.5.66.202     1742   17:34:45 

 --More--q

switch(config)#

Related Commands

Command	Description
clear ip msdp route	Clears routes in the MSDP Source-Active cache.
show ip msdp sa-cache	Displays information about the MSDP SA cache.

show ip msdp rpf

To display information about the Multicast Source Discovery Protocol (MSDP) next-hop autonomous system (AS) on the BGP path to an RP address, use the show ip msdp rpf command.

show ip msdp rpf rp-address [vrf {vrf-name all}]

Syntax Description

rp-address	IP address of the RP.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MSDP RPF peers:

switch(config)# show ip msdp rpf 192.168.1.10

MSDP RPF-Peer for RP 192.168.1.10, VRF default:

  Mesh-group check:

    Peer 192.168.1.10, mesh-group member of my_mesh_group

  Peer/route-lookup check:

    Peer 192.168.1.10, only MSDP peer configured, peer is RP

switch(config)#

show ip msdp sa-cache

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp sa-cache command.

show ip msdp {sa-cache | route} [{source [group]} | {group [source]}] [asn] [peer peer] [detail] [vrf {vrf-name | all}]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) AS number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

The show ip msdp route command is an alternative form of this command.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp sa-cache

MSDP SA Route Cache for Context "default" - 2138 entries

Source           Group            RP               ASN    Uptime   

24.124.36.130    224.0.1.1        144.228.240.250  1239   17:35:19 

64.104.160.29    224.0.1.1        204.69.199.17    109    17:35:19 

128.59.21.232    224.0.1.1        128.59.0.51      14     03:33:59 

128.117.37.217   224.0.1.1        128.117.243.9    194    04:07:17 

128.117.37.220   224.0.1.1        128.117.243.9    194    04:08:45 

129.49.88.9      224.0.1.1        199.109.44.1     5719   17:34:48 

130.18.14.12     224.0.1.1        192.208.151.9    10546  17:35:19 

130.37.20.4      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.20.5      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.20.7      224.0.1.1        145.145.255.6    1103   17:35:21 

130.37.64.252    224.0.1.1        145.145.255.6    1103   17:35:21 

130.88.20.1      224.0.1.1        194.66.25.224    786    17:35:19 

130.159.54.4     224.0.1.1        194.81.62.54     786    17:35:19 

130.159.228.48   224.0.1.1        194.81.62.54     786    17:35:19 

130.159.248.12   224.0.1.1        194.81.62.54     786    17:35:19 

132.234.1.1      224.0.1.1        132.234.251.232  7575   13:40:17 

134.174.190.41   224.0.1.1        192.5.66.202     1742   17:34:45 

 --More--q

switch(config)#

Related Commands

Command	Description
clear ip msdp sa-cache	Clears routes in the MSDP Source-Active cache.
show ip msdp route	Displays information about the MSDP SA cache.

show ip msdp sources

To display information about Multicast Source Discovery Protocol (MSDP) learned sources, use the show ip msdp sources command.

show ip msdp sources [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MSDP learned sources:

switch(config)# show ip msdp sources

MSDP Learned Sources and Group-Limit Information for VRF "default"

Source           Group Count  Group Limit  Source Prefix       Violations

18.7.25.94       1            unlimited    --                  0           

18.39.0.30       1            unlimited    --                  0           

18.62.10.96      1            unlimited    --                  0           

18.62.10.177     1            unlimited    --                  0           

18.89.2.245      1            unlimited    --                  0           

24.124.36.130    1            unlimited    --                  0           

62.40.98.21      1            unlimited    --                  0           

62.40.98.52      1            unlimited    --                  0           

62.40.98.75      1            unlimited    --                  0           

62.40.98.117     1            unlimited    --                  0           

62.40.98.139     1            unlimited    --                  0           

62.40.98.140     1            unlimited    --                  0           

62.40.98.152     1            unlimited    --                  0           

62.40.98.171     1            unlimited    --                  0           

62.40.98.202     1            unlimited    --                  0           

62.40.98.212     1            unlimited    --                  0           

 --More--q

switch(config)#

show ip msdp summary

To display summary information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp summary command.

show ip msdp summary [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display summary information about MSDP peers:

switch(config)# show ip msdp summary

MSDP Peer Status Summary for VRF "default"

Local ASN: 0, originator-id: 0.0.0.0

Number of configured peers:  1

Number of established peers: 0

Number of shutdown peers:    0

Peer            Peer        Connection      Uptime/   Last msg  (S,G)s

Address         ASN         State           Downtime  Received  Received

192.168.1.10    8           Listening       01:35:13  never     0

switch(config)#

show ip netstack mroute

To show IPv4 multicast routes in the Network Stack cache, use the show ip netstack mroute command.

show ip netstack mroute [vrf vrf-name]

Syntax Description

vrf vrf-name

(Optional) VRF name.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display multicast routes in the Network Stack cache:

switch(config)# show ip netstack mroute

(0.0.0.0/0, 225.1.1.1/32)

  Software switched packets: 1, bytes: 84

(4.1.1.2/32, 225.1.1.1/32), data-created

  Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.2/32)

  Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.2/32), data-created

  Software switched packets: 5, bytes: 420

(0.0.0.0/0, 225.1.1.3/32)

  Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.3/32), data-created

  Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.4/32)

  Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.4/32), data-created

  Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.5/32)

  Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.5/32), data-created

  Software switched packets: 2, bytes: 168

(0.0.0.0/0, 226.1.1.1/32)

  Software switched packets: 0, bytes: 0

(0.0.0.0/0, 226.2.2.2/32)

  Software switched packets: 0, bytes: 0

(0.0.0.0/0, 232.0.0.0/8)

  Software switched packets: 0, bytes: 0

switch(config)# 

show ip pim df

To display information about the designated forwarders (DFs) for IPv4 Protocol Independent Multicast (PIM), use the show ip pim df command.

show ip pim df [rp-or-group] [vrf {vrf-name | all}]

Syntax Description

rp-or-group	(Optional) RP or group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM DFs:

switch(config)# show ip pim df

Bidir-PIM Designated Forwarder Information for VRF "default"

RP Address (ordinal)   DF-bits          RP Metric  Group Range

2.2.2.2 (2)            00000002 (1)     [0/0]      224.128.0.0/9

  Interface            DF Address       DF State   DF Metric    DF Uptime

  Loopback0            1.1.1.1          Winner     [0/0]        00:28:14

  Ethernet2/2        	 10.2.0.2         Lose       [0/0]        00:28:14

switch(config)#

show ip pim event-history

To display information in the IPv4 Protocol Independent Multicast (PIM) event history buffers, use the show ip pim event-history command.

show ip pim event-history {errors | msgs | statistics}

Syntax Description||

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the PIM msgs event history buffer:

switch(config)# show ip pim event-history msgs

Note: PIM process currently not running

switch(config)#

Related Commands

Command	Description
clear ip pim event-history	Clears the contents of the PIM event history buffers.
ip pim event-history	Configures the size of PIM event history buffers.

show ip pim group-range

To display information about the group ranges for IPv4 Protocol Independent Multicast (PIM), use the show ip pim group-range command.

show ip pim group-range [group] [vrf {vrf-name | all}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM group ranges:

switch(config)# show ip pim group-range

PIM Group-Range Configuration for VRF "default"

Group-range        Mode      RP-address       Shared-tree-only range

239.128.1.0/24     SSM       -                -

224.0.0.0/9        ASM       192.0.2.33       -

switch(config)#

show ip pim interface

To display information about the enabled interfaces for IPv4 Protocol Independent Multicast (PIM), use the show ip pim interface command.

show ip pim interface [brief] [vrf {vrf-name | all}]

show ip pim interface if-type if-number

Syntax Description

brief	(Optional) Specifies a brief format for display.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM-enabled interfaces:

switch(config)# show ip pim interface ethernet 2/11

PIM Interface Status for VRF "default"

Ethernet2/11, Interface status: protocol-down/link-down/admin-up

  IP address: 192.168.1.222, IP subnet: 192.168.1.0/24

  PIM DR: 192.168.1.222, DR's priority: 5

  PIM neighbor count: 0

  PIM hello interval: 30 secs, next hello sent in: 00:00:03

  PIM neighbor holdtime: 105 secs

  PIM configured DR priority: 5

  PIM border interface: no

  PIM GenID sent in Hellos: 0x112ba48b

  PIM Hello MD5-AH Authentication: enabled

  PIM Neighbor policy: my_neighbor_policy

  PIM Join-Prune policy: none configured

  PIM Interface Statistics, last reset: never

    General (sent/received):

      Hellos: 3145/0, JPs: 0/0, Asserts: 0/0

      Grafts: 0/0, Graft-Acks: 0/0

      DF-Offers: 0/0, DF-Winners: 0/0, DF-Backoffs: 0/0, DF-Passes: 0/0

    Errors:

      Checksum errors: 0, Invalid packet types/DF subtypes: 0/0

      Authentication failed: 0

      Packet length errors: 0, Bad version packets: 0, Packets from self: 0

      Packets from non-neighbors: 0

      JPs received on RPF-interface: 0

      (*,G) Joins received with no/wrong RP: 0/0

      (*,G)/(S,G) JPs received for SSM/Bidir groups: 0/0

      JPs policy filtered: 0

switch(config)#

show ip pim neighbor

To display information about IPv4 Protocol Independent Multicast (PIM) neighbors, use the show ip pim neighbor command.

show ip pim neighbor {[if-type if-number] | [neighbor-addr]} [vrf {vrf-name | all}]

Syntax Description

if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
neighbor-addr	(Optional) IP address of a neighbor.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM neighbors:

switch(config)# show ip pim neighbor

PIM Neighbor Status for VRF "default"

Neighbor         Interface            Uptime    Expires   DR        Bidir-

                                                          Priority  Capable

2.1.1.2          Ethernet2/2          07:53:06  00:01:40  1         yes

switch(config)#

show ip pim oif-list

To display information about IPv4 Protocol Independent Multicast (PIM) interfaces for a group, use the show ip pim oif-list command.

show ip pim oif-list group [source] [vrf {vrf-name | all}]

Syntax Description

group	Group address.
source	(Optional) Source address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM interfaces for a group:

switch(config)# show ip pim oif-list 225.1.1.1

PIM OIF-List for VRF default 

(*, 225.1.1.1/32)

  Incoming interface: Ethernet2/1, RPF nbr 4.1.1.1

  Timeout interval: 38 secs left

  Oif-list (count: 0): (1) 00000010

  Timeout-list (count: 0): (0) 00000000

  Immediate-list (count: 0):

  Immediate-timeout-list (count: 0):

  Assert-lost-list (count: 1):

    Vlan5

switch(config)#

show ip pim policy statistics auto-rp

To display information about the Auto-RP policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics auto-rp command.

show ip pim policy statistics auto-rp {rp-candidate-policy | mapping-agent-policy} [vrf {vrf-name | all}]

Syntax Description

rp-candidate- policy	Specifies candidate-RP messages.
mapping- agent-policy	Specifies mapping agent messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics auto-rp rp-candidate-policy

C: No. of comparisions, M: No. of matches

route-map rpolicy permit 1

  match ip multicast group 225.1.1.0/24      C: 0      M: 0     

Total accept count for policy: 0     

Total reject count for policy: 0     

switch(config)# 

show ip pim policy statistics bsr

To display information about the bootstrap router (BSR) policy statistics for IPv4 Protocol Independent multicast (PIM), use the show ip pim policy statistics bsr command.

show ip pim policy statistics bsr {bsr-policy | rp-candidate-policy} [vrf {vrf-name | all}]

Syntax Description

bsr-policy	Specifies BSR messages.
rp-candidate- policy	Specifies candidate-RP messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics bsr bsr-policy

C: No. of comparisions, M: No. of matches

route-map rpolicy permit 1

  match ip multicast group 225.1.1.0/24      C: 0      M: 0     

Total accept count for policy: 0     

Total reject count for policy: 0     

switch(config)# 

show ip pim policy statistics jp-policy

To display information about the join-prune policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics jp-policy command.

show ip pim policy statistics jp-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics jp-policy ethernet 2/12

C: No. of comparisions, M: No. of matches

route-map rpolicy permit 1

  match ip multicast group 225.1.1.0/24         C: 0      M: 0     

Total accept count for policy: 0     

Total reject count for policy: 0     

switch(config)# 

show ip pim policy statistics neighbor-policy

To display information about the neighbor policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics neighbor-policy command.

show ip pim policy statistics neighbor-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics neighbor-policy ethernet 2/12

C: No. of comparisions, M: No. of matches

route-map rpolicy permit 1

  match ip multicast group 225.1.1.0/24         C: 0      M: 0     

Total accept count for policy: 0     

Total reject count for policy: 0     

switch(config)# 

show ip pim policy statistics register-policy

To display information about the register policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics register-policy command.

show ip pim policy statistics register-policy [vrf {vrf-name | all}]

Syntax Description

register-policy	Displays statistics for the register policy.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics register-policy vrf all

C: No. of comparisions, M: No. of matches

route-map rmap1 permit 10

  match ip multicast group 225.1.1.0/24                      C: 0      M: 0     

Total accept count for policy: 0     

Total reject count for policy: 0     

switch(config)# 

show ip pim route

To display information about the routes for IPv4 Protocol Independent Multicast (PIM), use the show ip pim route command.

show ip pim route {source group | group [source]} [vrf {vrf-name | all}]

Syntax Description

source	Source address.
group	Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM routes:

switch(config)# show ip pim route 224.1.1.1

PIM Routing Table for VRF "default" - 6 entries

(*, 224.0.0.0/4), RP 1.1.1.1*, bidir, expires 00:00:59, RP-bit

  Incoming interface: loopback4, RPF nbr 1.1.1.1 

  Oif-list: (0) 00000000, timeout-list: (0) 00000000

  Timeout-interval: 1, JP-holdtime round-up: 3

(*, 225.0.0.1/32), RP 1.1.1.1*, bidir, expires 0.000000 (00:00:06), RP-bit

  Incoming interface: loopback4, RPF nbr 1.1.1.1 

  Oif-list: (0) 00000000, timeout-list: (0) 00000000

  Timeout-interval: 1, JP-holdtime round-up: 3

(*, 225.0.1.1/32), RP 1.1.1.1*, bidir, expires 0.000000 (00:00:06), RP-bit

  Incoming interface: loopback4, RPF nbr 1.1.1.1 

  Oif-list: (0) 00000000, timeout-list: (0) 00000000

  Timeout-interval: 1, JP-holdtime round-up: 3

switch(config)#

show ip pim rp

To display information about the RPs for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp command.

show ip pim rp [group] [vrf {vrf-name | all}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM RPs:

switch(config)# show ip pim rp

PIM RP Status Information for VRF "default"

BSR: Not Operational

Auto-RP RPA: 192.168.1.222*, next Discovery message in: 00:00:06

BSR RP Candidate policy: my_bsr_rp_candidate_policy

BSR RP policy: my_bsr_policy

Auto-RP Announce policy: my_rp_candidate_policy

Auto-RP Discovery policy: my_mapping_agent_policy

Anycast-RP 192.0.2.3 members:

  192.0.2.31

RP: 192.0.2.33, (0), uptime: 04:08:11, expires: never,

  priority: 0, RP-source: (local), group ranges:

      224.0.0.0/9

switch(config)#

show ip pim rp-hash

To display information about the RP-hash values for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp-hash command.

show ip pim rp-hash group [vrf {vrf-name | all}]

Syntax Description

group	Group address for RP lookup.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM RP-hash values:

switch(config)# show ip pim rp-hash 224.1.1.1

PIM Hash Information for VRF "default"

PIM RPs for group 224.1.1.1, using hash-length: 0 from BSR: 10.2.0.1

  RP 10.2.0.1, hash: 1894762513 (selected)

switch(config)#

show ip pim statistics

To display information about the packet counter statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim statistics command.

show ip pim statistics [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(3)	Changed output to include vPC information when PIM is in vPC mode.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM statistics (if PIM is not in vPC mode, the vPC statistics are not displayed):

switch(config)# show ip pim statistics

PIM Global Counter Statistics for VRF:default, last reset: never

  Register processing (sent/received):

    Registers: 0/0, Null registers: 0/0, Register-Stops: 0/0

    Registers received and not RP: 0

    Registers received for SSM/Bidir groups: 0/0

  BSR processing (sent/received):

    Bootstraps: 0/0, Candidate-RPs: 0/0

    BSs from non-neighbors: 0, BSs from border interfaces: 0

    BS length errors: 0, BSs which RPF failed: 0

    BSs received but not listen configured: 0

    Cand-RPs from border interfaces: 0

    Cand-RPs received but not listen configured: 0

  Auto-RP processing (sent/received):

    Auto-RP Announces: 0/0, Auto-RP Discoveries: 0/0

    Auto-RP RPF failed: 0, Auto-RP from border interfaces: 0

    Auto-RP invalid type: 0, Auto-RP TTL expired: 0

    Auto-RP received but not listen configured: 0

  General errors:

    Control-plane RPF failure due to no route found: 0

    Data-plane RPF failure due to no route found: 0

    Data-plane no multicast state found: 0

    Data-plane create route state count: 2

  vPC packet stats:

    assert requests sent: 1

    assert requests received: 1

    assert request send error: 0

    assert response sent: 1

    assert response received: 1

    assert response send error: 0

    assert stop sent: 0

    assert stop received: 1

    assert stop send error: 0

switch(config)#

show ip pim vrf

To display informaion about IPv4 Protocol Independent Multicast (PIM) by virtual routing and forwarding (VRF) instance, use the show ip pim vrf command.

show ip pim vrf [vrf-name | all]

Syntax Description

vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM by VRF:

switch(config)# show ip pim vrf

switch(config)#

show ipv6 mld groups

To display information about the Multicast Listener Discovery (MLD) attached-group membership, use the show ipv6 mld groups command.

show ipv6 [icmp] mld groups [{source [group]} | {group [source]}] [if-type if-number] [vrf {vrf-name | all}]

Syntax Description

icmp	(Optional) Specifies ICMPv6 commands.
source	IPv6 source address.
group	(Optional) IPv6 multicast group address.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the MLD group membership:

switch(config)# show ipv6 mld groups

MLD Connected Group Membership for VRF "default" - 13 total entries (*, ff13::0001)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:25/00:03:54, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0002)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:21/00:03:58, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0003)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:22/00:03:57, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0004)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:23/00:03:56, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0005)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:24/00:03:55, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0006)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:25/00:03:54, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0007)

  Type: Local, Interface: Ethernet2/1

  Uptime/Expires: 00:00:27/00:03:52, Last Reporter: fe80::0230:48ff:fe34:0d5b

switch(config)#

show ipv6 mld local-groups

To display information about the local group membership for Multicast Listener Discovery (MLD), use the show ipv6 mld local-groups command.

show ipv6 [icmp] mld local-groups [if-type if-number] [vrf {vrf-name | all}]

Syntax Description

icmp	(Optional) Specifies ICMPv6 commands.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MLD local groups:

switch(config)# show ipv6 mld local-groups

MLD Locally Joined Group Membership for VRF "default"

Group   Type     Interface   Last Reported 

(*, ff13::0001)

        Local    Eth2/1      00:00:55  

(*, ff13::0002)

        Local    Eth2/1      00:00:46  

(*, ff13::0003)

        Local    Eth2/1      00:00:54  

(*, ff13::0004)

        Local    Eth2/1      00:00:51  

(*, ff13::0005)

        Local    Eth2/1      00:00:49  

(*, ff13::0006)

        Local    Eth2/1      00:00:46  

(*, ff13::0007)

        Local    Eth2/1      00:00:54  

(*, ff13::0008)

        Local    Eth2/1      00:00:52  

(*, ff13::0009)

        Local    Eth2/1      00:00:50  

(*, ff13::0010)

        Local    Eth2/1      00:00:48  

(*, ff14::0001)

        Local    Eth2/1      00:00:46  

(*, ff1e::0001)

        Local    Eth2/1      00:00:55  

(*, ff1e::0002)

        Static   Lo22        03:47:54  

switch(config)#

show ipv6 mroute

To display information about IPv6 multicast routes, use the show ipv6 mroute command.

show ipv6 mroute {group | {source group} | {group [source]}} [summary [software-forwarded]] [vrf {vrf-name | all}]

Syntax Description

group	Group address for route.
source	Source address for route.
summary	(Optional) Displays route counts and packet rates.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about multicast routes:

switch(config)# show ipv6 mroute

IPv6 Multicast Routing Table for VRF "default"

(*, ff30::/32), uptime: 1d02h, pim6 ipv6

  Incoming interface: Null, RPF nbr: 0::

  Outgoing interface list: (count: 0)

switch(config)# 

Related Commands

Command	Description
show ipv6 mroute summary	Displays summary information about IPv6 multicast routes.

show ipv6 mroute summary

To display summary information about IPv6 multicast routes, use the show ipv6 mroute summary command.

show ipv6 mroute summary [count | software-forwarded]] [vrf {vrf-name | all}]

show ipv6 mroute {group] summary [software-forwarded] [vrf {vrf-name | all}]

Syntax Description

count	(Optional) Displays only route counts.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
group	Specifies a group address for a route.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display summary information about multicast routes:

switch(config)# show ipv6 mroute summary

IPv6 Multicast Routing Table for VRF "default"

Total number of routes: 1

Total number of (*,G) routes: 0

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 0, rough average sources per group: 0.0

Group: ff30::/32, Source count: 0

Source            packets       bytes           aps   pps       bit-rate  oifs

(*,G)             0             0               0     0         0 bps     0

switch(config)# 

Related Commands

Command	Description
show ipv6 mroute	Displays information about IPv6 multicast routes.

show ipv6 pim df

To display information about the designated forwarders (DFs) for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim df command.

show ipv6 pim df [rp-or-group] [vrf {vrf-name | all}]

Syntax Description

rp-or-group	(Optional) RP or group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 DFs:

switch(config)# show ipv6 pim df

Bidir-PIM6 Designated Forwarder Information for VRF "default"

RP Address (ordinal)   RP Metric       Group Range

0001::0001 (7)

                       [0/0]           ff00::/8

  Interface     DF Address                 DF State DF Metric  DF Uptime

* Lo1           0::                        Lose     [0/0]      00:00:02

switch(config)#

show ipv6 pim event-history

To display information in the IPv6 Protocol Independent Multicast (PIM6) event history buffers, use the show ipv6 pim event-history command.

show ipv6 pim event-history {errors | msgs | statistics}

Syntax Description||

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the PIM6 msgs event history buffer:

switch(config)# show ipv6 pim event-history msgs

Note: PIM6 process currently not running

switch(config)#

Related Commands

Command	Description
clear ipv6 pim event-history	Clears the contents of the PIM6 event history buffers.
ipv6 pim event-history	Configures the size of PIM6 event history buffers.

show ipv6 pim group-range

To display information about IPv6 Protocol Independent Multicast (PIM6) group ranges, use the show ipv6 pim group-range command.

show ipv6 pim group-range [group] [vrf {vrf-name | all}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 group ranges:

switch(config)# show ipv6 pim group-range

PIM6 Group-Range Configuration for VRF "default"

Group-range               Mode      RP-address          Shared-tree-only range

ff30::/32                 SSM       -                   -

ff1e:abcd:def1::/96       ASM       2001:0db8:0000:abcd::0001

                                                        -

switch(config)#

show ipv6 pim interface

To display information about the enabled interfaces for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim interface command.

show ipv6 pim interface [brief] [vrf {vrf-name | all}]

show ipv6 pim interface if-type if-number

Syntax Description

brief	(Optional) Specifies a brief format for display.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6-enabled interfaces:

switch(config)# show ipv6 pim interface

PIM6 Interface Status for VRF "default"

Ethernet2/12, Interface status: protocol-down/link-down/admin-down

  IPv6 address: none

  PIM6 DR: 0::, DR's priority: ?

  PIM6 neighbor count: 0

  PIM6 hello interval: 23 secs (configured 22222 ms), next hello sent in: 00:00:08

  PIM6 neighbor holdtime: 81 secs

  PIM6 configured DR priority: 1

  PIM6 border interface: no

  PIM6 GenID sent in Hellos: 0x144b4667

  PIM6 Hello MD5-AH Authentication: disabled

  PIM6 Neighbor policy: none configured

  PIM6 Join-Prune policy: none configured

  PIM6 Interface Statistics, last reset: never

    General (sent/received):

      Hellos: 0/0, JPs: 0/0, Asserts: 0/0

      Grafts: 0/0, Graft-Acks: 0/0

      DF-Offers: 0/0, DF-Winners: 0/0, DF-Backoffs: 0/0, DF-Passes: 0/0

    Errors:

      Checksum errors: 0, Invalid packet types/DF subtypes: 0/0

      Authentication failed: 0

      Packet length errors: 0, Bad version packets: 0, Packets from self: 0

      Packets from non-neighbors: 0

      JPs received on RPF-interface: 0

      (*,G) Joins received with no/wrong RP: 0/0

      (*,G)/(S,G) JPs received for SSM/Bidir groups: 0/0

      JPs policy filtered: 0

switch(config)#

show ipv6 pim neighbor

To display information about IPv6 Protocol Independent Multicast (PIM6) neighbors, use the show ipv6 pim neighbor command.

show ipv6 pim neighbor {[if-type if-number] | [neighbor-addr]} [vrf {vrf-name | all}]

Syntax Description

if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
neighbor-addr	(Optional) IPv6 address of a neighbor.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 neighbors:

switch(config)# show ipv6 pim neighbor

PIM6 Neighbor Status for VRF "default"

Neighbor Address              Interface     Uptime    Expires   DR   Bidir

                                                                Pri

fe80::0230:48ff:fe34:0d67     Eth2/1        00:00:39  00:01:34  1    yes

  Secondary addresses:

    0001::0002

switch(config)#

show ipv6 pim oif-list

To display information about IPv6 Protocol Independent Multicast (PIM6) interfaces for a group, use the show ipv6 pim oif-list command.

show ipv6 pim oif-list group [source] [vrf {vrf-name | all}]

Syntax Description

group	Group address.
source	(Optional) Source address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM6 interfaces for a group:

switch(config)# show ipv6 pim oif-list ff1e::0002

PIM6 OIF-List for VRF default

(*, ff1e::0002/128)

  Incoming interface: Ethernet2/2, RPF nbr 0002::0002

  Timeout interval: 45 secs left

  Oif-list (count: 2):

    Ethernet8/11, uptime: 00:01:18, pim6

    Ethernet8/11, uptime: 00:01:18, pim6

  Timeout-list (count: 0):

  Immediate-list (count: 0):

  Immediate-timeout-list (count: 0):

switch(config)#

show ipv6 pim policy statistics jp-policy

To display information about the join-prune policy statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim policy statistics j-policy command.

show ipv6 pim policy statistics jp-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 policy statistics:

switch(config)# show ipv6 pim policy statistics jp-policy ethernet 2/2

C: No. of comparisions, M: No. of matches

route-map rmap1 permit 10

  match ipv6 multicast group ff1e::/128                       C: 0      M: 0     

Total accept count for policy: 2     

Total reject count for policy: 0     

switch(config)# 

show ipv6 pim policy statistics neighbor-policy

To display information about the neighbor policy statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim policy statistics neighbor-policy command.

show ipv6 pim policy statistics neighbor-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 policy statistics:

switch(config)# show ipv6 pim policy statistics neighbor-policy ethernet 2/2

C: No. of comparisions, M: No. of matches

route-map rmap2 permit 10

  match ipv6 multicast group ff1e::/128                       C: 0      M: 0     

Total accept count for policy: 2     

Total reject count for policy: 0     

switch(config)# 

show ipv6 pim route

To display information about IPv6 Protocol Independent Multicast (PIM6) routes, use the show ipv6 pim route command.

show ipv6 pim route {source group | group [source]} [vrf {vrf-name | all}]

Syntax Description

source	Source address.
group	Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM6 routes:

switch(config)# show ipv6 pim route

PIM6 Routing Table for VRF "default" - 1 entries

(*, ff30::/32), expires 00:02:33

  Incoming interface: Null, RPF nbr 0::

  Oif-list:       (0) 00000000, timeout-list: (0) 00000000

  Immediate-list: (0) 00000000, timeout-list: (0) 00000000

  Timeout-interval: 2, JP-holdtime round-up: 3

switch(config)#

show ipv6 pim rp

To display information about IPv6 Protocol Independent Multicast (PIM) RPs, use the show ipv6 pim rp command.

show ipv6 pim rp [group] [vrf {vrf-name | all}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 RPs:

switch(config)# show ipv6 pim rp

PIM6 RP Status Information for VRF "default"

BSR: 0::, uptime: 1d01h, expires: now,

      priority: 0, hash-length: 0

Auto-RP disabled

BSR RP Candidate policy: None

BSR RP policy: None

Auto-RP Announce policy: None

Auto-RP Discovery policy: None

RP: 2001:0db8:0000:abcd::0001, (0), uptime: 1d01h, expires: 0.000000,

 priority: 0, RP-source: (local), group ranges:

      ff1e:abcd:def1::/96

switch(config)#

show ipv6 pim rp-hash

To display information about the RP-hash values for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim rp-hash command.

show ipv6 pim rp-hash group [vrf {vrf-name | all}]

Syntax Description

group	Group address for the RP lookup.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 RP-hash values:

switch(config)# show ipv6 pim rp-hash

PIM6 Hash Information for VRF "default"

PIM6 RPs for group ff1e::0001, using hash-length: 126 from BSR: 0001::0001

  RP 0002::0001, hash: 1329585728 (selected)

show ip igmp snooping explicit-tracking

----------------------------------------

switch# show ip igmp snooping explicit-tracking vlan 33

IGMPv3 Snooping Explicit-tracking information

Source/Group            Intf      Reporter        Uptime    Last-Join Expires

1.1.1.1 232.1.1.1       Eth2/1    3.3.3.3         00:01:33  00:04:27

switch(config)#

show ipv6 pim statistics

To display information about the packet counter statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim statistics command.

show ipv6 pim statistics [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 statistics:

switch(config)# show ipv6 pim statistics

PIM6 Global Counter Statistics for VRF:default, last reset: never

  Register processing (sent/received):

    Registers: 0/0, Null registers: 0/0, Register-Stops: 0/0

    Registers received and not RP: 0

    Registers received for SSM/Bidir groups: 0/0

  BSR processing (sent/received):

    Bootstraps: 0/0, Candidate-RPs: 0/0

    BSs from non-neighbors: 0, BSs from border interfaces: 0

    BS length errors: 0, BSs which RPF failed: 0

    BSs received but not listen configured: 0

    Cand-RPs from border interfaces: 0

    Cand-RPs received but not listen configured: 0

  Auto-RP processing (sent/received):

    Auto-RP Announces: 0/0, Auto-RP Discoveries: 0/0

    Auto-RP RPF failed: 0, Auto-RP from border interfaces: 0

    Auto-RP invalid type: 0, Auto-RP TTL expired: 0

    Auto-RP received but not listen configured: 0

  General errors:

    Control-plane RPF failure due to no route found: 1

    Data-plane RPF failure due to no route found: 0

    Data-plane no multicast state found: 0

    Data-plane create route state count: 0

switch(config)#

show ipv6 pim vrf

To display informaion about IPv6 Protocol Independent Multicast (PIM6) by virtual routing and forwarding (VRF) instance, use the show ipv6 pim vrf command.

show ipv6 pim vrf [vrf-name | all]

Syntax Description

vrf-name	VRF name.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 by VRF:

switch(config)# show ipv6 pim vrf

switch(config)#

show routing ip multicast event-history

To display information in the IPv4 Multicast Routing Information Base (MRIB) event history buffers, use the show routing ip multicast event-history command.

show routing ip multicast event-history {cli | errors | mfdm | mfdm-stats | msgs | rib | statistics | vrf}

Syntax Description||

cli	Displays event history buffer of type CLI.
errors	Displays event history buffer of type errors.
mfdm	Displays event history buffer of type multicast FIB distribution (MFDM).
mfdm-stats	Displays event history buffer of type MFDM sum.
msgs	Displays event history buffer of type msgs.
rib	Displays event history buffer of type RIB.
statistics	Displays information about the event history buffers.
vrf	Displays event history buffer of type virtual routing and forwarding (VRF).

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the MRIB msgs event history buffer:

switch(config)# show routing ip multicast event-history msgs

Msg events for MRIB Process

1) Event:E_DEBUG, length:38, at 219263 usecs after Wed Jan  7 17:16:45 2009

    [100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 217482 usecs after Wed Jan  7 17:16:45 2009

    [100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:76, at 217477 usecs after Wed Jan  7 17:16:45 2009

    [100] : comp-mts-rx opc - from sap 27315 cmd mrib_internal_event_hist_command

4) Event:E_MTS_RX, length:60, at 535173 usecs after Wed Jan  7 17:16:36 2009

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X0021C74B, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1575, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0021C749, Sync:NONE, Payloadsize:120

    Payload:

    0x0000:  01 00 00 00 04 00 01 00 00 04 00 00 00 00 00 00

5) Event:E_MTS_RX, length:60, at 675244 usecs after Wed Jan  7 17:15:47 2009

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X0021C283, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1575, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0021C281, Sync:NONE, Payloadsize:148

    Payload:

    0x0000:  02 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

6) Event:E_MTS_RX, length:60, at 525065 usecs after Wed Jan  7 17:15:36 2009

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X0021C1F7, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1575, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0021C1F5, Sync:NONE, Payloadsize:120

    Payload:

    0x0000:  01 00 00 00 04 00 01 00 00 04 00 00 00 00 00 00

7) Event:E_MTS_RX, length:60, at 665138 usecs after Wed Jan  7 17:14:47 2009

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X0021BCBB, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1575, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0021BCB9, Sync:NONE, Payloadsize:148

    Payload:

    0x0000:  02 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

8) Event:E_MTS_RX, length:60, at 515080 usecs after Wed Jan  7 17:14:36 2009

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X0021BC34, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1575, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0021BC32, Sync:NONE, Payloadsize:120

    Payload:

    0x0000:  01 00 00 00 04 00 01 00 00 04 00 00 00 00 00 00

switch(config)#

Related Commands

Command	Description
ip routing multicast event-history	Configures the size of the IPv4 MRIB event history buffers.
clear ip routing multicast event-history	Clears information in the IPv4 MRIB event history buffers.

show routing ipv6 multicast

To display information about IPv6 multicast routes, use the show routing ipv6 multicast command.

show routing ipv6 multicast [vrf {vrf-name | all}] {{source group} | {group [source]}}

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
source	Source address for routes.
group	Group address for routes.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv6 multicast routes:

switch(config)# show routing ipv6 multicast

IPv6 Multicast Routing Table for VRF "default"

switch(config)#

show routing ipv6 multicast clients

To display information about IPv6 multicast routing clients, use the show routing ipv6 multicast clients command.

show routing ipv6 multicast clients [client-name]

Syntax Description

client-name

(Optional) One of the following multicast routing client names: •m6rib •icmpv6 •ipv6 •static •pim6

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv6 multicast routing clients:

switch(config)# show routing ipv6 multicast clients icmpv6

IPv6 Multicast Routing Client information

Client: icmpv6, client-id: 2, pid: 3742, mts-sap: 282

  Shared-memory: icmpv6, wants notifications

  Protocol is join-group owner

  Join notifications:         sent 1, fail 0, ack rcvd 1

  Prune notifications:        sent 0, fail 0, ack rcvd 0

  RPF notifications:          sent 0, fail 0, ack rcvd 0

  Delete notifications:       sent 0, fail 0, ack rcvd 0

  Clear mroute notifications: sent 0, fail 0

  Add route requests:         rcvd 0, ack sent 0, ack fail 0

  Delete route requests:      rcvd 0, ack sent 0, ack fail 0

switch(config)#

show routing ipv6 multicast event-history

To display information in the IPv6 Multicast Routing Information Base (M6RIB) event history buffers, use the show routing ipv6 multicast event-history command.

show routing ipv6 multicast event-history {cli | errors | mfdm | mfdm-stats | msgs | rib | statistics | vrf}

Syntax Description||

cli	Displays event history buffer of type CLI.
errors	Displays event history buffer of type errors.
mfdm	Displays event history buffer of type multicast FIB distribution (MFDM).
mfdm-stats	Displays event history buffer of type MFDM sum.
msgs	Displays event history buffer of type msgs.
rib	Displays event history buffer of type RIB.
statistics	Displays information about the event history buffers.
vrf	Displays event history buffer of type virtual routing and forwarding (VRF).

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the M6RIB msgs event history buffer:

switch(config)# show routing ipv6 multicast event-history msgs

Msg events for M6RIB Process

1) Event:E_DEBUG, length:38, at 269000 usecs after Tue Jan  6 18:45:50 2009

    [100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 267467 usecs after Tue Jan  6 18:45:50 2009

    [100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:76, at 267461 usecs after Tue Jan  6 18:45:50 2009

    [100] : comp-mts-rx opc - from sap 3389 cmd m6rib_internal_event_hist_command

4) Event:E_MTS_RX, length:60, at 335251 usecs after Tue Jan  6 18:45:21 2009

    [RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00049141, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0004913F, Sync:NONE, Payloadsize:268

    Payload:

    0x0000:  01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

5) Event:E_MTS_RX, length:60, at 325401 usecs after Tue Jan  6 18:44:21 2009

    [RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X000489A2, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x000489A0, Sync:NONE, Payloadsize:268

    Payload:

    0x0000:  01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

6) Event:E_MTS_RX, length:60, at 315289 usecs after Tue Jan  6 18:43:21 2009

    [RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00048457, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x00048455, Sync:NONE, Payloadsize:268

    Payload:

    0x0000:  01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

7) Event:E_MTS_RX, length:60, at 305189 usecs after Tue Jan  6 18:42:21 2009

    [RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00047EFD, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x00047EFB, Sync:NONE, Payloadsize:268

    Payload:

    0x0000:  01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

8) Event:E_MTS_RX, length:60, at 295210 usecs after Tue Jan  6 18:41:21 2009

    [RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X0004794F, Ret:SUCCESS

    Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x0004794D, Sync:NONE, Payloadsize:268

    Payload:

    0x0000:  01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

switch(config)#

Related Commands

Command	Description
ipv6 routing multicast event-history	Configures the size of the IPv6 M6RIB event history buffers.
clear ipv6 routing multicast event-history	Clears information in the IPv6 M6RIB event history buffers.

show routing multicast

To display information about IPv4 multicast routes, use the show routing multicast command.

show routing [ip | ipv4] multicast [vrf {vrf-name | all}] {{source group} | {group [source]}}

Syntax Description

ip	(Optional) Specifies IPv4 routes.
ipv4	(Optional) Specifies IPv4 routes.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name.
all	Specifies all VRFs.
source	Source address for routes.
group	Group address for routes.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv4 multicast routes:

switch(config)# show routing multicast

IP Multicast Routing Table for VRF "default"

(*, 239.128.1.0/24), uptime: 1d01h, pim

  Incoming interface: Null, RPF nbr: 0.0.0.0

  Outgoing interface list: (count: 0)

switch(config)#

show routing multicast clients

To display information about IPv4 multicast routing clients, use the show routing multicast clients command.

show routing [ip | ipv4] multicast clients [client-name]

Syntax Description

ip	(Optional) Specifies IPv4 multicast clients.
ipv4	(Optional) Specifies IPv4 multicast clients.
client-name	(Optional) One of the following multicast routing client names: •mrib •igmp •static •msdp •ip •pim

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv4 multicast clients:

switch(config)# show routing multicast clients pim

IP Multicast Routing Client information

Client: pim, client-id: 6, pid: 3982, mts-sap: 1568

  Shared-memory: pim, wants notifications

  Protocol is ssm owner, bidir owner, shared-only mode owner,

  Join notifications:         sent 1, fail 0, ack rcvd 1

  Prune notifications:        sent 0, fail 0, ack rcvd 0

  RPF notifications:          sent 0, fail 0, ack rcvd 0

  Delete notifications:       sent 0, fail 0, ack rcvd 0

  Clear mroute notifications: sent 0, fail 0

  Add route requests:         rcvd 2, ack sent 2, ack fail 0

  Delete route requests:      rcvd 1, ack sent 1, ack fail 0

switch(config)#

show running-config igmp

To display information about the running-system configuration for IGMP, use the show running-config igmp command.

show running-config igmp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the IGMP running-system configuration:

switch(config)# show running-config igmp

switch(config)# 

show running-config msdp

To display information about the running-system configuration for Multicast Source Discovery Protocol (MSDP), use the show running-config msdp command.

show running-config msdp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the MSDP running-system configuration:

switch(config)# show running-config msdp

version 4.0(3)

feature msdp

ip msdp originator-id loopback0

ip msdp peer 192.168.1.10 connect-source Ethernet2/11 remote-as 8

ip msdp sa-interval 88

ip msdp reconnect-interval 20

ip msdp group-limit 3 source 172.1.0.0/16

ip msdp group-limit 4000 source 192.168.1.0/24

ip msdp group-limit 4096 source 192.168.1.1/32

ip msdp flush-routes

ip msdp description 192.168.1.10 engineering peer

ip msdp keepalive 192.168.1.10 10 20

ip msdp sa-policy 192.168.1.10 my_sa_policy in

ip msdp mesh-group 192.168.1.10 my_mesh_group

switch(config)# 

show running-config pim

To display information about the running-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show running-config pim command.

show running-config pim [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the PIM running-system configuration:

switch(config)# show running-config pim

version 4.0(3)

feature pim

ip pim bsr-candidate Ethernet2/11

ip pim rp-address 192.0.2.33 group-list 224.0.0.0/9

ip pim rp-candidate Ethernet2/11 group-list 239.0.0.0/24 priority 3

ip pim auto-rp rp-candidate Ethernet2/12 group-list 239.0.0.0/24

ip pim send-rp-discovery Ethernet2/11 scope 30

ip pim log-neighbor-changes

ip pim bsr rp-candidate-policy my_bsr_rp_candidate_policy

ip pim bsr bsr-policy my_bsr_policy

ip pim auto-rp rp-candidate-policy my_rp_candidate_policy

ip pim auto-rp mapping-agent-policy my_mapping_agent_policy

ip pim ssm range 239.128.1.0/24

ip pim anycast-rp 192.0.2.3 192.0.2.31

ip pim auto-rp listen forward

ip pim state-limit 100000 reserved my_reserved_policy 40000

interface Ethernet2/11

  ip pim sparse-mode

  ip pim dr-priority 5

  ip pim hello-authentication ah-md5 3 78c3e5487bded5df

  ip pim neighbor-policy my_neighbor_policy

interface Ethernet2/12

  ip pim sparse-mode

switch(config)#

show running-config pim6

To display information about the running-system configuration for IPv6 Protocol Independent Multicast (PIM6), use the show running-config pim6 command.

show running-config pim6 [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the PIM6 running-system configuration:

switch(config)# show running-config pim6

version 4.0(3)

feature pim6

ipv6 pim bidir-rp-limit 3

ipv6 pim rp-address 2001:0db8::abcd:0000:0000:0000:0001 group-list ff1e:abcd:def1::/96

ipv6 pim rp-candidate Ethernet2/11 group-list ff1e:abcd:def1::/24

ipv6 pim register-policy my_register_policy

ipv6 pim ssm range ff30::/32

ipv6 pim flush-routes

interface Ethernet2/12

  ipv6 pim sparse-mode

  ipv6 pim hello-interval 22222

switch(config)#

show startup-config igmp

To display information about the startup-system configuration for IGMP, use the show startup-config igmp command.

show startup-config igmp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the IGMP startup-system configuration:

switch(config)# show startup-config igmp

switch(config)# 

show startup-config msdp

To display information about the startup-system configuration for Multicast Source Discovery Protocol (MSDP), use the show startup-config msdp command.

show startup-config msdp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the startup-system configuration for MSDP:

switch(config)# show startup-config msdp

version 4.0(3)

feature msdp

ip msdp originator-id loopback0

ip msdp peer 192.168.1.10 connect-source Ethernet2/11 remote-as 8

ip msdp sa-interval 88

ip msdp reconnect-interval 20

ip msdp group-limit 3 source 172.1.0.0/16

ip msdp group-limit 4000 source 192.168.1.0/24

ip msdp group-limit 4096 source 192.168.1.1/32

ip msdp flush-routes

ip msdp description 192.168.1.10 engineering peer

ip msdp keepalive 192.168.1.10 10 20

ip msdp sa-policy 192.168.1.10 my_incoming_sa_policy in

switch(config)#

show startup-config pim

To display information about the startup-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show startup-config pim command.

show startup-config pim [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the startup-system configuration for PIM:

switch(config)# show startup-config pim

version 4.0(3)

feature pim

ip pim bsr-candidate Ethernet2/11

ip pim rp-address 192.0.2.33 group-list 224.0.0.0/9

ip pim rp-candidate Ethernet2/11 group-list 239.0.0.0/24 priority 3

ip pim auto-rp rp-candidate Ethernet2/12 group-list 239.0.0.0/24

ip pim send-rp-discovery Ethernet2/11 scope 30

ip pim log-neighbor-changes

ip pim bsr rp-candidate-policy my_bsr_rp_candidate_policy

ip pim bsr bsr-policy my_bsr_policy

ip pim auto-rp rp-candidate-policy my_rp_candidate_policy

ip pim auto-rp mapping-agent-policy my_mapping_agent_policy

ip pim ssm range 239.128.1.0/24

ip pim anycast-rp 192.0.2.3 192.0.2.31

ip pim auto-rp listen forward

ip pim state-limit 100000 reserved my_reserved_policy 40000

interface Ethernet2/11

  ip pim sparse-mode

  ip pim dr-priority 5

  ip pim hello-authentication ah-md5 3 78c3e5487bded5df

  ip pim neighbor-policy my_neighbor_policy

interface Ethernet2/12

  ip pim sparse-mode

switch(config)#

show startup-config pim6

To display information about the startup-system configuration for IPv6 Protocol Independent Multicast (PIM6), use the show startup-config pim6 command.

show startup-config pim6 [all]

Syntax Description

all	(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the startup-system configuration for PIM6:

switch(config)# show startup-config pim6

version 4.0(3)

feature pim6

ipv6 pim bidir-rp-limit 3

ipv6 pim rp-address 2001:0db8::abcd:0000:0000:0000:0001 group-list ff1e:abcd:def1::/96

ipv6 pim rp-candidate Ethernet2/11 group-list ff1e:abcd:def1::/24

ipv6 pim register-policy my_register_policy

ipv6 pim ssm range ff30::/32

ipv6 pim flush-routes

interface Ethernet2/12

  ipv6 pim sparse-mode

  ipv6 pim hello-interval 22222

switch(config)#