Table Of Contents

Show Commands

show bgp

show bgp sessions

show forwarding

show forwarding distribution

show forwarding inconsistency

show glbp

show glbp capability

show hsrp

show hardware forwarding ip verify

show hsrp delay

show ip adjacency

show ip arp

show ip as-path-access-list

show ip bgp

show ip bgp community-list

show ip bgp dampening

show ip bgp filter-list

show ip bgp flap-statistics

show ip bgp history-paths

show ip bgp neighbors

show ip bgp nexthop

show ip bgp nexthop-database

show ip bgp prefix-list

show ip bgp peer-policy

show ip bgp peer-session

show ip bgp peer-template

show ip client

show ip community-list

show ip eigrp

show ip eigrp accounting

show ip eigrp interfaces

show ip eigrp neighbors

show ip eigrp policy statistics

show ip eigrp route-map statistics

show ip eigrp topology

show ip eigrp traffic

show ip fib

show ip fib distribution

show ip interface

show ip load-sharing

show ip mbgp

show ip mbgp community

show ip mbgp community-list

show ip mbgp dampening

show ip mbgp filter-list

show ip mbgp flap-statistics

show ip mbgp history-paths

show ip mbgp neighbors

show ip mbgp nexthop

show ip mbgp nexthop-database

show ip mbgp prefix-list

show ip ospf

show ip ospf border-routers

show ip ospf database

show ip ospf interface

show ip ospf lsa-content-changed-list

show ip ospf memory

show ip ospf neighbors

show ip ospf policy statistics area

show ip ospf policy statistics redistribute

show ip ospf request-list

show ip ospf retransmission-list

show ip ospf routes

show ip ospf statistics

show ip ospf summary-address

show ip ospf traffic

show ip ospf virtual-links

show ip rip

show ip policy

show ip prefix-list

show ip process

show ip rip interface

show ip rip neighbor

show ip rip policy statistics

show ip rip route

show ip rip statistics

show ip route

show ip static-route

show ip traffic

show ipv6 adjacency

show ipv6 client

show ipv6 fragments

show ipv6 icmp interface

show ipv6 interface

show ipv6 mbgp

show ipv6 mbgp community

show ipv6 mbgp community-list

show ipv6 nd interface

show ipv6 neighbor

show ipv6 prefix-list

show ipv6 process

show ipv6 route

show ipv6 static-route

show ipv6 traffic

show ospfv3

show ospfv3 border-routers

show ospfv3 database

show ospfv3 interface

show ospfv3 memory

show ospfv3 neighbors

show ospfv3 policy statistics area

show ospfv3 policy statistics redistribute

show ospfv3 request-list

show ospfv3 retransmission-list

show ospfv3 routes

show ospfv3 statistics

show ospfv3 summary-address

show ospfv3 traffic

show ospfv3 virtual-links

show routing

show routinghash

show track

Show Commands

---

This chapter describes the Cisco NX-OS unicast routing show commands.

show bgp

To display Border Gateway Protocol routes, use the show bgp command.

show bgp {{ipv4 | ipv6} {unicast | multicast} | all} [addr | prefix [longer-prefixes]] [vrf vrf-name]

Syntax Description

ipv4	(Optional) Display BGP information for IPv4 address family.
ipv6	(Optional) Display BGP information for IPv4 address family.
unicast	Displays BGP information for unicast address family.
multicast	Displays BGP information for multicast address family.
all	(Optional) Display BGP information for all address families.
addr	(Optional) A network from the selected address family. The format is A.B.C.D for IPv4 and A:B::C:D for IPv6.
prefix	Optional) A prefix from the selected address family. The format is A.B.C.D/length for IPv4 and A:B::C:D/length for IPv6.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(3)	Added support for IPv6 addresses and prefixes.

Usage Guidelines

This command does not require a license.

Examples

This example displays an entry in the BGP table:

switch(config-router)# show bgp ipv6 unicast

BGP routing table information for VRF default, address family IPv6 Unicast

Related Commands

Command	Description
clear bgp	Clears entries in the BGP table.

show bgp sessions

To display Border Gateway Protocol (BGP) sessions, use the show bgp sessions command.

show bgp sessions [vrf vrf-name]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays BGP sessions:

switch# show bgp sessions

Total peers 0, established peers 0

ASN 33.33

VRF default, local ASN 33.33

peers 0, established peers 0, local router-id 192.168.1.222

State: I-Idle, A-Active, O-Open, E-Established, C-Closing, S-Shutdown

Flaps LastUpDn|LastRead|LastWrit St Port(L/R)  Notif(S/R)

Related Commands

Command	Description
clear bgp	Clears BGP sessions.

show forwarding

To display forwarding information, use the show forwarding command.

show forwarding [ip | ipv4 | ipv6] {adjacency | interfaces | route} module slot [vrf vrf-name]

Syntax Description

ip	(Optional) Displays the IPv4 forwarding information.
ipv4	(Optional) Displays the IPv4 forwarding information.
ipv6	(Optional) Displays the IPv6 forwarding information.
adjacency	Displays the adjacency information.
interfaces	Displays the forwarding information for interfaces on a module.
route	(Optional) Displays the forwarding information for routes on a module.
module slot	Displays information for the module. The slot range depends on the hardware platform.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show forwarding command on the supervisor to view forwarding information on a module. Optionally, you can use the attach module command to attach to a module and use the show forwarding command on the module.

This command does not require a license.

Examples

This example displays forwarding information for module 2:

switch# show forwarding route module 2

IPv4 routes for table default/base

------------------+------------------+---------------------

Prefix            | Next-hop         | Interface

------------------+------------------+---------------------

0.0.0.0/32          Drop               Null0

255.255.255.255/32  Receive            sup-eth1

Related Commands

Command	Description
show ip fib	Displays information about the FIB.

show forwarding distribution

To display forwarding distribution information, use the show forwarding distribution command.

show forwarding distribution [clients | fib-state]

Syntax Description

clients	(Optional) Displays the forwarding distribution information for unicast clients.
fib-state	(Optional) Displays the forwarding distribution state for unicast FIB.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays forwarding information for unicast clients:

switch# show forwarding distribution clients

id  pid    shmem-start  shmem-end  shmem-name

--  -----  -----------  ---------  ----------

 1  3646   0x64f70120  0x64fc0000  u6rib-ufdm

 2  3647   0x64b50120  0x64d50000  urib-ufdm

Related Commands

Command	Description
show ip fib distribution	Displays distribution information about the FIB.

show forwarding inconsistency

To display the results of the forwarding inconsistency checker, use the show forwarding inconsistency command.

show forwarding inconsistency [ip | ipv4] [unicast] module slot [vrf vrf-name]

Syntax Description

ip	(Optional) Displays the IPv4 forwarding inconsistency information.
ipv4	(Optional) Displays the IPv4 forwarding inconsistency information.
unicast	(Optional) Displays the forwarding inconsistency information for unicast routes
module slot	Displays inconsistency information for the module. The slot range depends on the hardware platform.
vrf vrf-name	(Optional) Displays inconsistency information for the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

Use the show forwarding inconsistency command to display the results of the test forwarding inconsistency command.

This command does not require a license.

Examples

This example displays forwarding inconsistency information for module 2:

switch# show forwarding inconsistency module 2

Consistency check : table_id(0x1) slot(2)

No inconsistent adjacencies.

No inconsistent routes.

Related Commands

Command	Description
test forwarding inconsistency	Triggers the forwarding inconsistency checker.

show glbp

To display Gateway Load Balancing Protocol (GLBP) information, use the show glbp command.

show glbp [interface type number] [group number] [state] [brief] [vrf vrf-name]

Syntax Description

interface type number	(Optional) Specifies the interface to display GLBP information.
group number	(Optional) Specifies the GLBP group number. The range is from 0 to 1023.
state	(Optional) State of the GLBP router. The states are as follows: active, disabled, init, listen, or standby.
brief	(Optional) Summarizes each virtual gateway or virtual forwarder with a single line of output.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names. Supported in Cisco NX-OS Release 4.0(2) and later releases.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(2)	Added support for vrf keyword.

Usage Guidelines

Use the show glbp command to display information about GLBP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

This command does not require a license.

Examples

The following example shows how to display GLBP information:

switch# show glbp

Ethernet2/1 - Group 10

  State is Active

    2 state changes, last state change 23:50:33

  Virtual IP address is 192.0.2.10

  Hello time 5 sec, hold time 18 sec

    Next hello sent in 4.300 secs

  Redirect time 600 sec, forwarder time-out 7200 sec

  Authentication MD5, key "ThisStringIsTheSecretKey"

  Preemption enabled, min delay 60 sec

  Active is local

  Standby is unknown

  Priority 254 (configured)

  Weighting 105 (configured 110), thresholds: lower 95, upper 105

    Track object 2 state Down decrement 5

  Load balancing: host-dependent

  Group members:

    0016.C76C.85DC (7.199.10.1) local

  There is 1 forwarder (1 active)

  Forwarder 1

    State is Active

      1 state change, last state change 23:50:15

    MAC address is 0007.b400.0101 (default)

    Owner ID is 0005.0050.6c08

    Redirection enabled

    Preemption enabled, min delay 60 sec

    Active is local, weighting 105

The following example shows how to display a brief summary of GLBP information:

switch# show glbp brief

Interface   Grp  Fwd Pri State    Address         Active router   Standby router

Eth2/1      10   -   254 Active   192.0.2.10       local           unknown       

Eth1/2      10   1   7   Active   0007.b400.0101   local           -

The following example shows how to specify the GLBP interface and group number:

switch# show glbp interface ethernet2/2 group 1

Ethernet2/2 - Group 1

 State is Listen

   64 state changes, last state change 00:00:54

 Virtual IP address is 10.1.0.7

 Hello time 50 msec, hold time 200 msec

   Next hello sent in 0.030 secs

 Redirect time 600 sec, forwarder time-out 14400 sec

 Authentication text "authword"

 Preemption enabled, min delay 0 sec

 Active is 10.1.0.2, priority 105 (expires in 0.184 sec)

 Standby is 10.1.0.3, priority 100 (expires in 0.176 sec)

 Priority 96 (configured)

 Weighting 100 (configured 100), thresholds: lower 95, upper 100

   Track object 1 state Up decrement 10

 Load balancing: round-robin

  Group members:

   0004.4d83.4801 (10.0.0.0)

   0010.7b5a.fa41 (10.0.0.1)

   00d0.bbd3.bc21 (10.0.0.2) local

Table 1-1 describes the significant fields shown in the displays.

Table 1-1 show glbp Field Descriptions 

Field	Description
Ethernet2/1 - Group	Interface type and number and GLBP group number for the interface.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: •Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. •Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. •Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. •Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. •Speak—The virtual gateway is attempting to become the active or standby virtual gateway. •Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: •Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. •Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. •Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. •Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
Virtual IP address is	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Hello time, hold time	Time between hello packets, in seconds or milliseconds, that indicates the hello time. The hold time is the time (in seconds or milliseconds) before other routers declare the active router to be down. All routers in a GLBP group use the hello-time and hold-time values of the current AVG. If the locally configured values are different, the configured values appear in parentheses after the hello-time and hold-time values.
Redirect time, forwarder time-out	Redirect and timeout times for an AVF transition to a standby virtual forwarder. The redirect time is the time during which the AVG for a GLBP group continues to redirect clients to a secondary AVF. The timeout is the time (in seconds) before the secondary virtual forwarder becomes unavailable.
Preemption	Whether GLBP gateway preemption is enabled. If enabled, the minimum delay is the time, in seconds, for which a higher-priority nonactive router will wait before preempting the lower-priority active router. This field is also displayed under the forwarder section where it indicates GLBP forwarder preemption.
Active is	Active state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the current AVG. This field is also displayed under the forwarder section where it indicates the address of the current AVF.
Standby is	Standby state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the standby gateway (the gateway that is next in line to be the AVG).
Weighting	Initial weighting value with lower and upper threshold values.
Track object	List of objects that are being tracked and their corresponding states.
Load balancing	Load-balancing method configured for the GLBP group.
Group members	List of gateways that are members of this group.
Forwarder	List of forwarders in this group.

Table 1-2 describes the fields for the show glbp brief command output.

Table 1-2 show glbp brief Field Descriptions 

Field	Description
Interface	Interface type and number. GLBP group number for the interface.
Grp	GLBP group number for the interface.
Fwd	Number of forwarders in the GLBP group.
Pri	Configured priority for this gateway.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: •Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. •Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. •Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. •Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. •Speak—The virtual gateway is attempting to become the active or standby virtual gateway. •Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: •Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. •Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. •Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. •Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
Address	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Active router	IP address of the AVG.
Standby router	IP address of the standby virtual gateway.

Related Commands

Command	Description
glbp ip	Enables GLBP.
glbp timers	Configures the time between hello messages and the time before other routers declare the active GLBP router to be down.
glbp weighting track	Specifies an object to be tracked that affects the weighting of a GLBP gateway.

show glbp capability

To display which interfaces support Gateway Load Balancing Protocol (GLBP), use the show glbp capability command.

show glbp [interface type number] [port-channel number] [vlan number]

Syntax Description

interface type number	(Optional) Specifies the interface for which output is displayed.
port-channel number	(Optional) Specifies the port channel for which output is displayed.
vlan number	(Optional) VLAN for which output is displayed.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show glbp capability command to display which interfaces support GLBP.

This command does not require a license.

Examples

This example shows how to display the interfaces that support GLBP:

switch# show glbp capability

                 Nexus7010 (10 Slot) Chassis * means interface may support GLBP

                                            |

         Interface                     Type |  Potential Max Groups

            Eth1/1   2     Gigabit Ethernet *  1024

            Eth1/2   2     Gigabit Ethernet *  1024

            Eth2/1   2     Gigabit Ethernet *  1024

            Eth2/2   2     Gigabit Ethernet *  1024

            Eth2/3   2     Gigabit Ethernet *  1024

            Eth2/4   2     Gigabit Ethernet *  1024

            Eth2/5   2     Gigabit Ethernet *  1024

            Eth2/6   2     Gigabit Ethernet *  1024

            Eth2/7   2     Gigabit Ethernet *  1024

            Eth2/8   2     Gigabit Ethernet *  1024

             mgmt0   5  Management Sup Port    0

   Eth Inband Port  21         Inband  Port    0

   Eth Inband Port  21         Inband  Port    0

   Eth Inband Port  21         Inband  Port    0

Table 1-3 describes the significant fields shown in the output.

Table 1-3 show glbp capability Field Descriptions 

Field	Description
Interface	Interface name.
Type	Interface type.
GLBP support (represented by the | character)	* indicates the interface may support GLBP.
Potential Max Groups	Maximum number of groups supported by this interface.

Related Commands

Command	Description
glbp ip	Enables GLBP.
glbp timers	Configures the time between hello messages and the time before other routers declare the active GLBP router to be down.
glbp weighting track	Specifies an object to be tracked that affects the weighting of a GLBP gateway.

show hsrp

To display Hot Standby Router Protocol (HSRP) information for each HSRP group, use the show hsrp command.

show hsrp [interface type number] [group group-number] [active | init | listen | standby] [all] [brief]

Syntax Description

interface type number	(Optional) Specifies the interface type and number for which to display HSRP information.
group group-number	(Optional) Specifies the HSRP group number of the interface to display information about.
active	(Optional) Displays HSRP groups that are in an active state.
init	(Optional) Displays HSRP groups that are in an initialization state.
listen	(Optional) Displays HSRP groups that are in an listen state.
standby	(Optional) Displays HSRP groups that are in an standby state.
all	(Optional) Displays all HSRP groups.
brief	(Optional) Summarizes each virtual gateway or virtual forwarder with a single line of output.

Command Modes

Any

Supported User Roles

Superuser
VDC administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show hsrp command to display information about HSRP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

This command does not require a license.

Examples

The following example shows how to display GLBP information:

switch# show hsrp

show hsrp

Ethernet0/0/1 - Group 1

State is Init (standby RP, peer state is Active)

Virtual IP address is 10.1.0.7

Active virtual MAC address is unknown

Local virtual MAC address is 000a.f3fd.5001 (bia)

Hello time 1 sec, hold time 3 sec

Authentication text "authword"

Preemption enabled

Active router is unknown

Standby router is unknown

Priority 110 (configured 120)

Track object 1 state Down decrement 10

IP redundancy name is "name1" (cfgd)

The following example shows how to display a brief summary of GLBP information:

switch# show hsrp brief

P indicates configured to preempt.

|

Interface Grp Prio P State Active addr Standby addr Group addr

Et1 1 105 P Active local 192.168.21.2 192.168.21.10

The following example shows how to specify the GLBP interface and group number:

switch# show glbp interface ethernet2/2 group 1

Ethernet2/2 - Group 1

 State is Listen

   64 state changes, last state change 00:00:54

 Virtual IP address is 10.1.0.7

 Hello time 50 msec, hold time 200 msec

   Next hello sent in 0.030 secs

 Redirect time 600 sec, forwarder time-out 14400 sec

 Authentication text "authword"

 Preemption enabled, min delay 0 sec

 Active is 10.1.0.2, priority 105 (expires in 0.184 sec)

 Standby is 10.1.0.3, priority 100 (expires in 0.176 sec)

 Priority 96 (configured)

 Weighting 100 (configured 100), thresholds: lower 95, upper 100

   Track object 1 state Up decrement 10

 Load balancing: round-robin

  Group members:

   0004.4d83.4801 (10.0.0.0)

   0010.7b5a.fa41 (10.0.0.1)

   00d0.bbd3.bc21 (10.0.0.2) local

Table 1-1 describes the significant fields shown in the displays.

Table 1-4 show glbp Field Descriptions 

Field	Description
Ethernet2/1 - Group	Interface type and number and GLBP group number for the interface.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: •Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. •Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. •Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. •Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. •Speak—The virtual gateway is attempting to become the active or standby virtual gateway. •Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: •Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. •Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. •Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. •Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
Virtual IP address is	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Hello time, hold time	Time between hello packets, in seconds or milliseconds, that indicates the hello time. The hold time is the time (in seconds or milliseconds) before other routers declare the active router to be down. All routers in a GLBP group use the hello-time and hold-time values of the current AVG. If the locally configured values are different, the configured values appear in parentheses after the hello-time and hold-time values.
Redirect time, forwarder time-out	Redirect and timeout times for an AVF transition to a standby virtual forwarder. The redirect time is the time during which the AVG for a GLBP group continues to redirect clients to a secondary AVF. The timeout is the time (in seconds) before the secondary virtual forwarder becomes unavailable.
Preemption	Whether GLBP gateway preemption is enabled. If enabled, the minimum delay is the time, in seconds, for which a higher-priority nonactive router will wait before preempting the lower-priority active router. This field is also displayed under the forwarder section where it indicates GLBP forwarder preemption.
Active is	Active state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the current AVG. This field is also displayed under the forwarder section where it indicates the address of the current AVF.
Standby is	Standby state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the standby gateway (the gateway that is next in line to be the AVG).
Weighting	Initial weighting value with lower and upper threshold values.
Track object	List of objects that are being tracked and their corresponding states.
Load balancing	Load-balancing method configured for the GLBP group.
Group members	List of gateways that are members of this group.
Forwarder	List of forwarders in this group.

Table 1-2 describes the fields for the show glbp brief command output.

Table 1-5 show glbp brief Field Descriptions 

Field	Description
Interface	Interface type and number. GLBP group number for the interface.
Grp	GLBP group number for the interface.
Fwd	Number of forwarders in the GLBP group.
Pri	Configured priority for this gateway.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: •Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. •Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. •Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. •Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. •Speak—The virtual gateway is attempting to become the active or standby virtual gateway. •Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: •Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. •Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. •Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. •Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
Address	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Active router	IP address of the AVG.
Standby router	IP address of the standby virtual gateway.

Related Commands

Command	Description
glbp ip	Enables GLBP.
glbp timers	Configures the time between hello messages and the time before other routers declare the active GLBP router to be down.
glbp weighting track	Specifies an object to be tracked that affects the weighting of a GLBP gateway.

show hardware forwarding ip verify

To display information about IP packet verification, use the show hardware forwarding ip verify command.

show hardware version ip verify

Syntax Description

This command has no keywords or arguments

Command Modes

Any

Supported User Roles

Superuser
VDC administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example shows IP packet verification settings:

switch# show hardware forwarding ip verify

IPv4 and v6 IDS Checks         Status     Packets Failed

-----------------------------+---------+------------------

address source broadcast       Enabled    0

address source multicast       Enabled    0

address destination zero       Enabled    0

address identical              Enabled    0

address source reserved        Enabled    0

address class-e                Disabled   0

checksum                       Enabled    0

protocol                       Enabled    0

fragment                       Enabled    0

length minimum                 Enabled    0

length consistent              Enabled    0

length maximum max-frag        Enabled    0

length maximum udp             Disabled   0

length maximum max-tcp         Enabled    0

tcp flags                      Disabled   0

tcp tiny-frag                  Enabled    0

version                        Enabled    0

-----------------------------+---------+------------------

IPv6 IDS Checks                Status     Packets Failed

-----------------------------+---------+------------------

length consistent              Enabled    0

length maximum max-frag        Enabled    0

length maximum udp             Disabled   0

length maximum max-tcp         Enabled    0

tcp tiny-frag                  Enabled    0

version                        Enabled    0

Related Commands

Command	Description
platform ip verify address	Configures IPv4 and IPv6 packet verification checks based on addresses.
platform ip verify length	Configures IPv4 packet verification checks based on length.
platform ipv6 verify	Configures IPv6 packet verification.

show hsrp delay

To display Hot Standby Router Protocol (HSRP) group delay information, use the show hsrp delay command.

show hsrp delay [interface type number] [group group-number] [all] [brief]

Syntax Description

interface type number	(Optional) Specifies the interface type and number for which to display HSRP information.
group group-number	(Optional) Specifies the HSRP group number of the interface to display information about.

Command Modes

Any

Supported User Roles

Superuser
VDC administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show hsrp delay command to display delay information about HSRP groups.

This command does not require a license.

Examples

The following example shows how to display GLBP delay information:

switch# show hsrp delay

show ip adjacency

To display adjacency information, use the show ip adjacency command.

show ip adjacency [ip-addr | interface] [detail] [non-best] [statistics] [summary] [vrf vrf-name]

Syntax Description

ip-addr	(Optional) An IPv4 source address. The format is x.x.x.x.
interface	(Optional) An interface. Use ? to determine the supported interface types.
detail	(Optional) Displays detailed adjacency information.
non-best	(Optional) Displays both the best and nonbest adjacency information.
statistics	(Optional) Displays adjacency statistics.
summary	(Optional) Displays a summary of the adjacency information.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays a summary of the adjacency information:

switch# show ip adjacency summary

IP AM Table - Adjacency Summary

  Static  : 1

  Dynamic : 22

  Others  : 0

  Total   : 23

Related Commands

Command	Description
show forwarding adjacency	Displays forwarding adjacency information.

show ip arp

To display the Address Resolution Protocol (ARP) information, use the show ip arp command.

show ip arp [ip-addr | interface] [client] [static] [statistics] [summary] [vrf vrf-name]

Syntax Description

ip-addr	(Optional) An IPv4 source address. The format is x.x.x.x.
interface	(Optional) An interface. Use ? to determine the supported interface types.
client	(Optional) Displays the ARP client table
static	(Optional) Displays static ARP entries.
statistics	(Optional) Displays ARP statistics.
summary	(Optional) Displays a summary of the ARP table.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays a summary of the ARP table:

switch# show ip arp summary

IP ARP Table - Adjacency Summary

  Resolved   : 33

  Incomplete : 0

  Unknown    : 0

  Total      : 33

Related Commands

Command	Description
ip arp timeout	Configures ARP.

show ip as-path-access-list

To display the AS Path access lists for the Border Gateway Protocol (BGP), use the show ip as-path-access-list command.

show ip as-path-access-list [name]

Syntax Description

name	(Optional) AS path access list name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the AS path access lists:

switch# show ip as-path-access-list

ip as-path access-list Test1 permit "10.0.0.1"

Related Commands

Command	Description
ip as-path access-list	Configures an AS path access list.

show ip bgp

To display entries in the Border Gateway Protocol (BGP) table, use the show ip bgp command.

show ip bgp [ip-addr | ip-prefix [longer-prefixes]] [received-paths] [regexp expression] [route-map map-name] [summary] [vrf vrf-name]

Syntax Description

ip-addr	(Optional)A network from the BGP route table. The format is x.x.x.x.
ip-prefix	(Optional) A prefix from the the BGP route table. The format is x.x.x.x/length.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
received-paths	(Optional) Displays paths stored for soft reconfiguration.
regexp expression	(Optional) Display information that matches the regular expression.
route-map map-name	(Optional) Displays routes that match the route map. The map name can be any case-sensitive alphanumeric string up to 64 characters.
summary	(Optional) Displays the summary of the routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP route table:

switch(config-router)# show ip bgp

BGP routing table information for VRF default, address family IPv4 Unicast

Related Commands

Command	Description
clear ip bgp	Clears entries in the BGP route table.

show ip bgp community-list

To display Border Gateway Protocol (BGP) routes that match a community list, use the show ip bgp community-list command.

show ip bgp [ipv4 {unicast | multicast} | all] community-list commlist-name [exact-match]} [vrf vrf-name]

Syntax Description

ipv4	(Optional) Display BGP information for IPv4 address family.
ipv6	(Optional) Display BGP information for IPv4 address family.
unicast	Displays BGP information for unicast address family.
multicast	Displays BGP information for multicast address family.
all	(Optional) Display BGP information for all address families.
community-list commlist-name	Display routes matching the community-list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a community list:

switch(config)# show ip bgp community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip bgp dampening

To display Border Gateway Protocol (BGP) dampening information, use the show ip bgp dampening command.

show ip bgp [ipv4 {unicast | multicast} | all] dampening {dampened-paths [regexp expression] | flap-statistics | history-paths [regexp expression] | parameters} [vrf vrf-name]

Syntax Description

ipv4	(Optional) Display BGP information for IPv4 address family.
ipv6	(Optional) Display BGP information for IPv4 address family.
unicast	Displays BGP information for unicast address family.
multicast	Displays BGP information for multicast address family.
all	(Optional) Display BGP information for all address families.
dampened-paths	Display all dampened paths.
regexp expression	(Optional) Display information that matches the regular expression.
flap-statistics	Display flap statistics for routes.
history-paths	Display all history paths.
parameters	Display all dampening parameters.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays dampening information:

switch(config)# show ip bgp dampening dampened-paths

show ip bgp filter-list

To display Border Gateway Protocol (BGP) routes that match a filter list, use the show ip bgp filter-list command.

show ip bgp filter-list list-name [exact-match] [vrf vrf-name]

Syntax Description

list-name	Name of a filter-list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a filter list:

switch(config)# show ip bgp filter-list test1

show ip bgp flap-statistics

To display Border Gateway Protocol (BGP) flap statistics, use the show ip bgp flap-statistics command.

show ip bgp flap-statistics [prefix] [vrf vrf-name]

Syntax Description

prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the flap statistics:

switch(config)# show ip bgp flap-statistics

Related Commands

Command	Description
show ip bgp	Displays BGP information.

show ip bgp history-paths

To display Border Gateway Protocol (BGP) history paths, use the show ip bgp history-paths command.

show ip bgp [ipv4 {unicast | multicast} | all] history-paths [regexp expression] [vrf vrf-name]

Syntax Description

ipv4	(Optional) Display BGP information for IPv4 address family.
ipv6	(Optional) Display BGP information for IPv4 address family.
unicast	Displays BGP information for unicast address family.
multicast	Displays BGP information for multicast address family.
all	(Optional) Display BGP information for all address families.
regexp expression	(Optional) Display information that matches the regular expression.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays BGP history path information:

switch(config)# show ip bgp history-paths

show ip bgp neighbors

To display Border Gateway Protocol (BGP) neighbors, use the show ip bgp neighbors command.

show ip bgp neighbors [ addr | prefix] [vrf vrf-name]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP neighbors:

switch(config)# show ip bgp neighbors

show ip bgp nexthop

To display Border Gateway Protocol (BGP) next hop information, use the show ip bgp nexthop command.

show ip bgp nexthop addr [vrf vrf-name]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP next-hop information:

switch(config)# show ip bgp nexthop 192.0.2.1

show ip bgp nexthop-database

To display Border Gateway Protocol (BGP) next-hop database, use the show ip bgp nexthop-database command.

show ip bgp nexthop-database [vrf vrf-name]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP next-hop database:

switch(config)# show ip bgp nexthop-database

Related Commands

Command	Description
show ip bgp	Displays BGP information.

show ip bgp prefix-list

To display Border Gateway Protocol (BGP) routes that match a prefix list, use the show ip bgp prefix-list command.

show ip bgp prefix-list list-name [exact-match] [vrf vrf-name]

Syntax Description

list-name	Name of a prefix list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a prefix list:

switch(config)# show ip bgp prefix-list test1

show ip bgp peer-policy

To display Border Gateway Protocol (BGP) peer policy template information, use the show ip bgp peer-policy command.

show ip bgp peer-policy name

Syntax Description

name	Name of a BGP template. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP peer policy:

switch(config)# show ip bgp peer-policy test1

Commands configured in this template:

  Send Community

  Suppress Inactive

  Default Originate - route-map:

Inherited commands:

Inherited by the following peers:

  VRF default: 192.0.2.3

Related Commands

Command	Description
inherit peer-policy	Inherits a peer policy template for a neighbor.
template peer-policy	Configures a peer policy template.

show ip bgp peer-session

To display Border Gateway Protocol (BGP) peer session template information, use the show ip bgp peer-session command.

show ip bgp peer-session name

Syntax Description

name	Name of a BGP template. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP peer session:

switch(config)# show ip bgp peer-session test1

Commands configured in this template:

  Update Source - interface: Vlan33

  EBGP Multihop - hop limit: 33

Inherited commands:

Inherited by the following peers:

  VRF default: 192.0.2.3

Related Commands

Command	Description
inherit peer-session	Inherits a peer session template for a neighbor.
template peer-session	Configures a peer session template.

show ip bgp peer-template

To display Border Gateway Protocol (BGP) peer template information, use the show ip bgp peer-template command.

show ip bgp peer-template name

Syntax Description

name	Name of a BGP template. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP peer template:

switch(config)# show ip bgp peer-template peer1

BGP peer-template is peer1

  Connected check is disabled

  Hold time = 0, keepalive interval is 0 seconds

  Message statistics:

                              Sent               Rcvd

  Opens:                         0                  0

  Notifications:                 0                  0

  Updates:                       0                  0

  Keepalives:                    0                  0

  Route Refresh:                 0                  0

  Capability:                    0                  0

  Total:                         0                  0

  Total bytes:                   0                  0

  Bytes in queue:                0                  0

Members of peer-template peer1:

default:192.0.2.3

Related Commands

Command	Description
inherit peer-template	Inherits a peer template for a neighbor.
template peer	Configures a peer template.

show ip client

To display information about the internal IP clients, use the show ip client command.

show ip client [name]

Syntax Description

name	(Optional) Name of client.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the IP client information for ARP:

switch(config)# show ip client arp

Client: arp, uuid: 268, pid: 3687, extended pid: 3687

  Protocol: (none), client-index: 2, routing VRF id: 255

  Data MTS-SAP: 0

  Data messages, send successful: 33, failed: 0

Related Commands

Command	Description
show ip process	Displays information about the IP process.

show ip community-list

To display community lists for the Border Gateway Protocol (BGP), use the show ip community-list command.

show ip community-list [name]

Syntax Description

name	(Optional) Name of community list. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the community lists:

switch(config)# show ip community-list 

Standard Community List test2

    permit internet local-AS

Related Commands

Command	Description
ip community-list	Configures a BGP community list.

show ip eigrp

To display a summary of the Enhanced Interior Gateway Routing Protocol (EIGRP) processes, use the show ip eigrp command.

show ip eigrp [instance-tag]

Syntax Description

instance-tag

(Optional) Instance tag. The instance tag can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example displays all the EIGRP instances:

switch# show ip eigrp 

IP-EIGRP AS 0 ID 0.0.0.0 VRF default

  Process-tag: Test1

  Status: shutdown

  Authentication mode: none

  Authentication key-chain: none

  Metric weights: K1=1 K2=0 K3=1 K4=0 K5=0

  IP proto: 88 Multicast group: 224.0.0.10

  Int distance: 90 Ext distance: 170

  Max paths: 8

  Number of EIGRP interfaces: 0 (0 loopbacks)

  Number of EIGRP peers: 0

IP-EIGRP AS 0 ID 0.0.0.0 VRF default

  Process-tag: Test2

  Status: shutdown

  Authentication mode: none

  Authentication key-chain: none

  Metric weights: K1=1 K2=0 K3=1 K4=0 K5=0

  IP proto: 88 Multicast group: 224.0.0.10

  Int distance: 90 Ext distance: 170

  Max paths: 8

  Number of EIGRP interfaces: 0 (0 loopbacks)

  Number of EIGRP peers: 0

show ip eigrp accounting

To display prefix accounting information for the Enhanced Interior Gateway Routing Protocol (EIGRP) processes, use the show ip eigrp accounting command.

show ip eigrp [vrf {vrf-name | *}] [instance-tag] accounting

Syntax Description

vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
instance-tag	(Optional) Instance tag. This option is available when a virtual routing and forwarding (VRF) instance is not specified. The instance tag can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

The following example shows how to display the EIGRP accounting information:

switch# show ip eigrp accounting

IP-EIGRP accounting for AS(100)/ID(192.0.2.1) vrf RED

Total Prefix Count: 4  

States: A-Adjacency, P-Pending, D-Down

State Address/Source   Interface        Prefix   Restart  Restart/

                                        Count     Count   Reset(s)

 P    Redistributed     ----               0           3         211

 A    192.0.2.2          e2/1              2           0          84

 P    192.0.2.4          e3/3              0           2         114

 D    192.0.2.3          e4/1              0           3           0

Table 1-6 describes the significant fields shown in the display.

Table 1-6 show ip eigrp accounting Field Descriptions 

Field	Description
IP-EIGRP accounting for AS...	EIGRP instance, AS number, router ID, and table ID.
Total Prefix Count:	Aggregate sum of the prefixes in an EIGRP instance topology table. The count includes prefixes learned from all neighbors or from redistribution.
States: A-Adjacency, P-Pending, D-Down	A-Adjacency: Indicates a stable adjacency with the neighbor or a normal redistribution state. P-Pending: Neighbor adjacency or redistribution is suspended or in a penalized state because the maximum prefix limit was exceeded. D-Down: Neighbor adjacency or redistribution is suspended permanently until a manual reset is performed with the clear route command.
Address/Source	Peer IP address of the redistribution source.
Prefix Count	Total number of learned prefixes by source. Note Routes can be learned for the same prefix from multiple sources, and the sum of all prefix counts in this column may be greater than the figure displayed in the "Prefix Count" field.
Restart Count	Number of times that a route source exceeded the maximum prefix limit.
Restart Reset(s)	Time, in seconds, that a route source is in a P (penalized) state. If the route source is in an A (stable or normal) state, the displayed time, in seconds, is the time period until penalization history is reset.

show ip eigrp interfaces

To display information about interfaces configured for the Enhanced Interior Gateway Routing Protocol (EIGRP), use the show ip eigrp interfaces command.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] interfaces [type instance] [brief] [detail]

Syntax Description

instance-tag	(Optional) The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
type	(Optional) Interface type. For more information, use the question mark (?) online help function.
instance	(Optional) Either a physical interface instance or a virtual interface instance. Specifying instance removes all entries learned through this interface from the neighbor table. The instance argument has the following syntax: •Physical interface instance. Naming notation is slot/port and a slash mark between values is required as part of the notation. •Virtual interface instance. The number range varies depending on the interface type. For more information about the syntax for the router, use the question mark (?) online help function.
brief	(Optional) Displays brief summary of EIGRP interface information.
detail	(Optional) Displays detailed EIGRP interface information.

Defaults

This command shows all interfaces for the default VRF if no VRF or no interface is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(3)	Added brief keyword.

Usage Guidelines

Use the show ip eigrp interfaces command to determine on which interfaces EIGRP is active and learn information about EIGRP related to those interfaces.

If you specify an interface, only that interface is displayed. Otherwise, all interfaces on which EIGRP is running are displayed.

If you specify an autonomous system, only the routing process for the specified autonomous system is displayed. Otherwise, all EIGRP processes are displayed.

This command requires the Enterprise Services license.

Examples

The following example shows how to display information about EIGRP interfaces:

switch# show ip eigrp interfaces

IP EIGRP interfaces for process 1 vrf default

                         Xmit Queue    Mean   Pacing Time   Multicast   Pending

Interface        Peers   Un/Reliable   SRTT   Un/Reliable   Flow Timer  Routes

e2/2               0         0/0          0      11/434          0          0

e2/20              1         0/0        337       0/10           0          0

e4/2               1         0/0         10       1/63         103          0

e3/2               1         0/0        330       0/16           0          0

switch#

Table 1-7 describes the significant fields shown in the display.

Table 1-7 show ip eigrp interfaces Field Descriptions 

Field	Description
Interface	Interface over which EIGRP is configured.
Peers	Number of directly connected EIGRP neighbors.
Xmit Queue Un/Reliable	Number of packets remaining in the unreliable and reliable transmit queues.
Mean SRTT	Mean smoothed round-trip time (SRTT) internal (in milliseconds).
Pacing Time Un/Reliable	Pacing time used to determine when EIGRP packets should be sent out the interface (unreliable and reliable packets).
Multicast Flow Timer	Maximum number of seconds in which the router sends multicast EIGRP packets.
Pending Routes	Number of routes in the packets in the transmit queue waiting to be sent.

The following example shows how to display more details about the EIGRP interfaces:

switch# show ip eigrp interfaces detail

IP-EIGRP interfaces for AS 1 vrf default

                        Xmit Queue   Mean   Pacing Time   Multicast    Pending

Interface        Peers  Un/Reliable  SRTT   Un/Reliable   Flow Timer   Routes

e 2/6              1        0/0         3       0/10          50           0

  Hello interval is 5 sec, hold time is 15 sec

  Next xmit serial <none>

  Un/reliable mcasts: 0/4  Un/reliable ucasts: 6/3

  Mcast exceptions: 0  CR packets: 0  ACKs suppressed: 1

  Retransmissions sent: 0  Out-of-sequence rcvd: 1

  Bandwidth percent is 50

  Authentication mode is not set

switch#

Table 1-8 describes the significant fields shown in the display.

Table 1-8 show ip eigrp interfaces detail Field Descriptions 

Field	Description
Hello interval	Hello packet transmission interval.
hold time	Hold time announced to neighbors. If neighbors do not get hello packets from the router for this period, neighbors declare that the neighbor relationship is down.
Next xmit serial	Next transmission serial number.
Un/reliable mcasts	Number of unreliable and reliable multicast packets sent on this interface.
Un/reliable ucasts	Number or unreliable and reliable unicast packets sent on this interface.
Mcast exceptions	Number of multicast exceptions (sequence TLVs).
CR packets	Number of packets sent with the conditional receive bit set.
ACKs suppresses	Number of ACK packets suppressed.
Retransmissions	Number of retransmissions sent on this interface.
Out-of-sequence rcvd	Number of packets received out of sequence.
Bandwidth percent	Configured percent of bandwidth.
Authentication	Mode of authentication.

Related Commands

Command	Description
show ip eigrp neighbors	Displays the neighbors discovered by EIGRP.

show ip eigrp neighbors

To display information about neighbors discovered by the Enhanced Interior Gateway Routing Protocol (EIGRP), use the show ip eigrp neighbors command.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] neighbors [detail] [interface-type interface-instance] [static]

Syntax Description

instance-tag	The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
detail	(Optional) Displays detailed EIGRP neighbor information.
interface-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
interface-instance	(Optional) Either a physical interface instance or a virtual interface instance. Specifying instance removes all entries learned through this interface from the neighbor table. The instance argument has the following syntax: •Physical interface instance. Naming notation is slot/port and a slash mark between values is required as part of the notation. •Virtual interface instance. The number range varies depending on the interface type. For more information about the syntax for the router, use the question mark (?) online help function.
static	(Optional) Displays static EIGRP interface information.

Defaults

This command displays all neighbors for the default VRF on all interfaces if no VRF or interface is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp neighbors command to determine when neighbors become active and inactive. This command is also useful for debugging certain types of transport problems.

This command requires the Enterprise Services license.

Examples

The following example shows how to display information about EIGRP neighbors:

switch# show ip eigrp neighbors

IP-EIGRP Neighbors for process 77 vrf default

Address                 Interface     Holdtime Uptime   Q      Seq  SRTT  RTO

                                      (secs)   (h:m:s)  Count  Num  (ms)  (ms)

192.0.2.28                 e1/3         13       0:00:41  0      11   4     20

192.0.2.2                  e4/4         14       0:02:01  0      10   12    24

switch#

Table 1-9 describes the significant fields shown in the display.

Table 1-9 show ip eigrp neighbors Field Descriptions 

Field	Description
process	Autonomous system number specified in the router configuration command.
vrf	VRF name.
Address	IP address of the EIGRP peer.
Interface	Interface on which the router is receiving hello packets from the peer.
Holdtime	Length of time (in seconds) that the Cisco NX-OS oftware waits to hear from the peer before declaring that the peer is down.
Uptime	Elapsed time (in hours, minutes, and seconds) since the local router first heard from this neighbor.
Q Count	Number of EIGRP packets (update, query, and reply) that the software waits to send.
Seq Num	Sequence number of the last update, query, or reply packet that was received from this neighbor.
SRTT	Smoothed round-trip time. This field indicates the number of milliseconds required for an EIGRP packet to be sent to this neighbor and for the local router to receive an acknowledgment of that packet.
RTO	Retransmission timeout (in milliseconds). This field indicates the amount of time that the software waits before resending a packet from the retransmission queue to a neighbor.

The following example shows how to display detailed information about EIGRP neighbors:

switch# show ip eigrp neighbors detail 

IP-EIGRP neighbors for AS 1 vrf default

H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq

                                            (sec)         (ms)       Cnt Num

0   192.0.2.10               e1/5            14 01:00:52    3    200   0  10

   Version 12.4/1.2, Retrans: 0, Retries: 0, Prefixes: 3

switch#

Table 1-10 describes the significant fields shown in the display.

Table 1-10 show ip eigrp neighbors detail Field Descriptions 

Field	Description
Version	Version of EIGRP software running on the node and neighbor.
Retrans:	Number of retransmissions sent to this neighbor.
Retries:	Number of retransmissions sent to this neighbor since the last acknowledgement (ACK).
Prefixes	Number of prefixes learned from this neighbor.

Related Commands

Command	Description
clear ip eigrp neighbors	Clears neighbors for EIGRP.

show ip eigrp policy statistics

To display the policy statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP, use the show ip eigrp policy statistics command in any mode.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] policy statistics redistribute {bgp id | direct | eigrp id | isis id | ospf id | rip id | static}

Syntax Description

instance-tag	The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for EIGRP.
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for the Open Shortest Path First (OSPF) protocol.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(13	This command was removed and replaced by the show ip eigrp route-map statistics command.

Usage Guidelines

This command does not require a license.

Examples

The following example shows how to display policy statistics for EIGRP:

switch(config)# show ip eigrp policy statistics redistribute direct

C: No. of comparisons, M: No. of matches

route-map rmap1 permit 1

Total accept count for policy: 10

Total reject count for policy: 0

Related Commands

Related Commands

Command	Description
clear ip eigrp policy statistics	Clears policy statistics for EIGRP.
show ip eigrp traffic	Displays EIGRP traffic statistics.

show ip eigrp route-map statistics

To display the route redistribution statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP, use the show ip eigrp route-map statistics command in any mode.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] route-map statistics redistribute {bgp id | direct | eigrp id | isis id | ospf id | rip id | static}

Syntax Description

instance-tag	(Optional) Instance tag. The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for EIGRP.
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for the Open Shortest Path First (OSPF) protocol.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command replaces the show ip eigrp policy statistics command. This command does not require a license.

Examples

The following example shows how to display route-map statistics for EIGRP:

switch(config)# show ip eigrp route-map statistics redistribute direct

C: No. of comparisons, M: No. of matches

route-map rmap1 permit 1

Total accept count for policy: 10

Total reject count for policy: 0

Related Commands

Related Commands

Command	Description
clear ip eigrp route-map statistics	Clears route-map statistics for EIGRP.
show ip eigrp traffic	Displays EIGRP traffic statistics.

show ip eigrp topology

To display the Enhanced Interior Gateway Routing Protocol (EIGRP) topology table, use the show eigrp topology command.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] topology [ip-address/length] [active | all-links | detail-links | pending | summary | zero-successors]

Syntax Description

instance-tag	(Optional) Instance of EIGRP. The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.
ip-address/length	(Optional) IP address in four-part, dotted-decimal notation with a network mask indicated as a slash (/) and number. For example, /8 indicates that the first 8 bits of the mask are 1s, and the corresponding bits of the address are the network address.
active	(Optional) Displays only active entries in the EIGRP topology table.
all-links	(Optional) Displays all entries in the EIGRP topology table.
detail-links	(Optional) Displays detailed information for all entries in the EIGRP topology table.
pending	(Optional) Displays all entries in the EIGRP topology table that are waiting for an update from a neighbor or are waiting to reply to a neighbor.
summary	(Optional) Displays a summary of the EIGRP topology table.
zero-successors	(Optional) Displays available routes in the EIGRP topology table.

Defaults

This command displays information for the default VRF if no VRF is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp topology command to determine Diffusing Update Algorithm (DUAL) states and to debug possible DUAL problems.

When you use the show ip eigrp topology command without any keywords or arguments, Cisco NX-OS displays only routes that are feasible successors.

This command requires the Enterprise Services license.

Examples

This example shows how to display the EIGRP topology table. The EIGRP metrics for specified internal routes and external routes are displayed.

switch# show ip eigrp topology 10.2.1.0/24

IP-EIGRP (AS 1): Topology entry for 192.0.2.0/24

  State is Passive, Query origin flag is 1, 1 Successor(s), FD is 281600

  Routing Descriptor Blocks:

   192.0.2.22 (Ethernet 2/1), from 10.2.1.1, Send flag is 0x0

    Composite metric is (409600/128256), Route is External

    Vector metric:

      Minimum bandwidth is 10000 Kbit

      Total delay is 6000 microseconds

      Reliability is 255/255

      Load is 1/255

      Minimum MTU is 1500

      Hop count is 1

    External data:

      Originating router is 10.89.245.1 

      AS number of route is 0

      External protocol is Connected, external metric is 0

      Administrator tag is 0 (0x00000000)

switch#

This example show the all-links option:

switch(config)# show ip eigrp topology all-links 

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

       r - reply Status, s - sia Status 

P 3.3.3.0/24, 1 successors, FD is 130816, serno 58

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 2.2.2.0/24, 1 successors, FD is 130816, serno 57

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 1.1.1.0/24, 1 successors, FD is 130816, serno 56

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 192.168.6.0/24, 1 successors, FD is 2816, serno 25

        via Connected, Ethernet2/2

        via 192.168.5.2 (26112/2816), Ethernet2/1

P 6.6.6.0/24, 1 successors, FD is 128256, serno 24

        via Connected, loopback6

P 5.5.5.0/24, 1 successors, FD is 128256, serno 23

        via Connected, loopback5

P 4.4.4.0(1)/24, 1 successors, FD is 128256, serno 16

        via Connected, loopback4

P 192.168.5.0/24, 1 successors, FD is 25856, serno 1

        via Connected, Ethernet2/1

        via 192.168.6.2 (3072/2816), Ethernet2/2

This example shows more details:

switch(config)# show ip eigrp topology detail-links 

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

       r - reply Status, s - sia Status 

P 3.3.3.0/24, 1 successors, FD is 130816, serno 58

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 2.2.2.0/24, 1 successors, FD is 130816, serno 57

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 1.1.1.0/24, 1 successors, FD is 130816, serno 56

        via 192.168.6.2 (130816/128256), Ethernet2/2

        via 192.168.5.2 (153856/128256), Ethernet2/1

P 192.168.6.0/24, 1 successors, FD is 2816, serno 25

        via Connected, Ethernet2/2

        via 192.168.5.2 (26112/2816), Ethernet2/1

P 6.6.6.0/24, 1 successors, FD is 128256, serno 24

        via Connected, loopback6

P 5.5.5.0/24, 1 successors, FD is 128256, serno 23

        via Connected, loopback5

P 4.4.4.0(1)/24, 1 successors, FD is 128256, serno 16

        via Connected, loopback4

P 192.168.5.0/24, 1 successors, FD is 25856, serno 1

        via Connected, Ethernet2/1

        via 192.168.6.2 (3072/2816), Ethernet2/2

This example shows a summary of the topology table:

switch(config)# show ip eigrp topology summary 

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Head serial 1, next serial 59

8 routes, 0 pending replies, 0 dummies

IP-EIGRP(0) enabled on 5 interfaces, 2 neighbors present on 2 interfaces

Quiescent interfaces:  Eth2/2 Eth2/1

This example shows the active entries in the topology table:

switch(config-if)# show ip eigrp topology active

IP-EIGRP Topology Table for AS(101)/ID(80.86.2.3) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

        r - reply Status, s - sia Status

A 8.3.2.0/24, 1 successors, FD is Inaccessible

     1 replies, active 00:00:04, query-origin: Local origin

         via Connected (Infinity/Infinity), loopback8

       Remaining replies:

          via 5.5.5.6, r, Ethernet2/6

This example shows zero-successors in the topology table:

switch(config-router)# show ip eigrp topology zero-successors

IP-EIGRP Topology Table for AS(101)/ID(10.1.48.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

        r - reply Status, s - sia Status

P 10.1.49.0/24, 0 successors, FD is Inaccessible

         via 5.5.5.5 (28416/28160), Ethernet2/6

This example shows pending entries:

switch(config)# show ip eigrp topology pending

IP-EIGRP Topology Table for AS(100)/ID(1.1.1.1) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

       r - reply Status, s - sia Status

P 6.6.6.0/24, 1 successors, FD is 130816, U

        via 192.168.5.1 (130816/128256), Ethernet2/1

P 5.5.5.0/24, 1 successors, FD is 130816, U

        via 192.168.5.1 (130816/128256), Ethernet2/1

P 4.4.4.0(1)/24, 1 successors, FD is 130816, U

        via 192.168.5.1 (130816/128256), Ethernet2/1

P 8.8.8.0/24, 1 successors, FD is 130816, U

        via 192.168.5.1 (130816/128256), Ethernet2/1

Table 1-11 describes the significant fields shown in the display.

Table 1-11 show ip eigrp topology Field Descriptions 

Field	Description
Query origin	Query origin state.
Successors	Number of feasible successors for this prefix.
FD	Feasible distance for this prefix.
10.2.1.1 (Gi0/0)	Next hop and interface from which this path was learned.
from 10.2.1.1	Information source for this path.
Send flag	Status of whether the sending of this prefix is pending to this neighbor.
Composite metric is...	The first number is the EIGRP metric that represents the cost to the destination. The second number is the EIGRP metric that this peer advertised.
Route is	Type of route (internal or external).
Vector Metric	Metric (bandwidth, delay, reliability, load, MTU, and hop count) advertised by the neighbor.
External Data	External information (originating router ID, AS number, external protocol, metric, and tag) advertised by the neighbor.

show ip eigrp traffic

To display the number of Enhanced Interior Gateway Routing Protocol (EIGRP) packets sent and received, use the show ip eigrp traffic command.

show ip eigrp [instance-tag] [vrf {vrf-name | *}] traffic

Syntax Description

instance-tag	(Optional) Instance of EIGRP. The instance tag can be any case-sensitive alphanumeric string up to 64 characters.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

This command displays information for the default VRF if no VRF is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp traffic command to find the number of packets sent and received by this EIGRP instance.

In addition, this command is useful in determining whether packets from one node are not reaching the neighboring node due to connectivity or configuration problems.

This command requires the Enterprise Services license.

Examples

The following example shows how to display the EIGRP traffic statistics:

switch# show ip eigrp traffic

IP-EIGRP Traffic Statistics for AS 1 vrf default

  Hellos sent/received: 736/797

  Updates sent/received: 6/6

  Queries sent/received: 0/1

  Replies sent/received: 1/0

  Acks sent/received: 6/6

  Input queue high water mark 0, 0 drops

  SIA-Queries sent/received: 0/0

  SIA-Replies sent/received: 0/0

Table 1-12 describes the significant fields shown in the display.

Table 1-12 show eigrp traffic Field Descriptions 

Field	Description
AS 1	Autonomous system number specified in the router eigrp command.
vrf default	VRF specified in the show command.
Hellos sent/received:	Number of hello packets sent and received.
Updates sent/received:	Number of update packets sent and received.
Queries sent/received:	Number of query packets sent and received.
Replies sent/received:	Number of reply packets sent and received.
Acks sent/received:	Number of acknowledgment packets sent and received.
Input queue high water mark	Maximum number of packets in the input queue and number of drops.
SIA-Queries sent/received	Number of Stuck-in-Active query packets sent and received.
SIA-Replies sent/received:	Number of Stuck-in-Active reply packets sent and received.

show ip fib

To display forwarding information, use the show ip fib command.

show ip fib {adjacency | interfaces | route} module slot

Syntax Description

adjacency	Displays the adjacency information.
interfaces	Displays the forwarding information for interfaces on a module.
route	(Optional) Displays the forwarding information for routes on a module.
module slot	Displays information for the module. The slot range depends on the hardware platform.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip fib command on the supervisor to view forwarding information on a module. Optionally, you can use the attach module command to attach to a module and use the show ip fib command on the module.

This command does not require a license.

Examples

This example displays forwarding information for module 2:

switch# show ip fib route module 2

IPv4 routes for table default/base

------------------+------------------+---------------------

Prefix            | Next-hop         | Interface

------------------+------------------+---------------------

0.0.0.0/32          Drop               Null0

255.255.255.255/32  Receive            sup-eth1

Related Commands

Command	Description
show forwarding	Displays information about the FIB.

show ip fib distribution

To display forwarding distribution information, use the show ip fib distribution command.

show ip fib distribution [clients | state]

Syntax Description

clients	(Optional) Displays the forwarding distribution information for unicast clients.
state	(Optional) Displays the forwarding distribution state for unicast FIB.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays forwarding information for unicast clients:

switch# show ip fib distribution clients

id  pid    shmem-start  shmem-end  shmem-name

--  -----  -----------  ---------  ----------

 1  3646   0x64f70120  0x64fc0000  u6rib-ufdm

 2  3647   0x64b50120  0x64d50000  urib-ufdm

Related Commands

Command	Description
show forwarding distribution	Displays distribution information about the FIB.

show ip interface

To display IP information for an interface, use the show ip interface command.

show ip interface [type number] [brief][vrf vrf-name]

Syntax Description

type	(Optional) Interface type. Use ? to see the options.
number	(Optional) Interface number. Use ? to see the range.
brief	(Optional) Displays a summary of IP information.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays IP information for Ethernet 2/1:

switch# show ip interface ethernet 2/1 

Ethernet2/1, Interface status: protocol-down/link-down/admin-down, iod: 80,

  IP VRF context: "default"

  IP address: 192.0.2.1, IP subnet: 192.0.0.0/8

  IP broadcast address: 255.255.255.255

  IP multicast groups locally joined: none

  IP MTU: 1500 bytes (using link MTU)

  IP primary address route-preference: 0, tag: 0

  IP proxy ARP : disabled

  IP Local Proxy ARP : disabled

  IP multicast routing: disabled

  IP icmp redirects: enabled

  IP directed-broadcast: disabled

  IP icmp unreachables (except port): disabled

  IP icmp port-unreachable: enabled

  IP RP inbound packet-filtering policy: none

  IP RP outbound packet-filtering policy: none

  IP inbound packet-filtering policy: none

  IP outbound packet-filtering policy: none

  IP unicast reverse path forwarding: none

  IP unicast reverse path forwarding fail policy: none

  IP interface statistics last reset: never

  IP interface software stats: (sent/received/forwarded/originated/consumed)

    Unicast packets    : 0/0/0/0/0

    Unicast bytes      : 0/0/0/0/0

    Multicast packets  : 0/0/0/0/0

    Multicast bytes    : 0/0/0/0/0

    Broadcast packets  : 0/0/0/0/0

    Broadcast bytes    : 0/0/0/0/0

    Labeled packets    : 0/0/0/0/0

    Labeled bytes      : 0/0/0/0/0

Related Commands

Command	Description
show ipv6 interface	Displays IPv6 information about an interface.

show ip load-sharing

To display IP load sharing information, use the show ip load-sharing command.

show ip load-sharing

Syntax Description

This command has no arguments or keywords.

Command Modes

Any

Supported User Roles

Network Administrator
VDC Administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays IP load sharing information:

switch# show ip load-sharing

IPv4/IPv6 ECMP load sharing:

Universal-id (Random Seed): 2823428857

Load-share mode : address source-destination port source-destination Broadcast bytes    : 
0/0/0/0/0

    Labeled packets    : 0/0/0/0/0

    Labeled bytes      : 0/0/0/0/0

Related Commands

Command	Description
show ip load-sharing	Displays IP load sharing.

show ip mbgp

To display entries in the Multiprotocol Border Gateway Protocol (MBGP) table, use the show ip mbgp command.

show ip mbgp [p-addr | ip-prefix [longer-prefixes]] [received-paths] [regexp expression] [route-map map-name] [summary] [vrf vrf-name]

Syntax Description

ip-addr	(Optional)A network from the MBGP route table. The format is x.x.x.x.
ip-prefix	(Optional) A prefix from the the MBGP route table. The format is x.x.x.x/length.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
received-paths	(Optional) Displays paths stored for soft reconfiguration.
regexp expression	(Optional) Display information that matches the regular expression.
route-map map-name	(Optional) Displays routes that match the route map. The map name can be any case-sensitive alphanumeric string up to 64 characters.
summary	(Optional) Displays the summary of the routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the MBGP route table:

switch(config-router)# show ip mbgp

BGP routing table information for VRF default, address family IPv4 Multicast

Related Commands

Command	Description
clear ip mbgp	Clears entries in the MBGP route table.

show ip mbgp community

To display Multiprotocol Border Gateway Protocol (MBGP) routes that match a community, use the show ip mbgp community command.

show ip mbgp community [as-number] [internet] [no-advertise] [no-export] [no-export-subconfed] [exact-match]} [vrf vrf-name]

Syntax Description

as-number	AS number. The AS number can be a 16-bit integer or a 32-bit integer in the form of <higher 16-bit decimal number>.<lower 16-bit decimal number>.
internet	(Optional) Displays the internet community.
no-advertise	(Optional) Displays the no-advertise community.
no-export	(Optional) Displays the no-export community.
no-export-subconfed	(Optional) Displays the no-export-subconfed community.
exact-match	(Optional) Displays an exact match of the community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a community:

switch(config)# show ip mbgp community 

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip mbgp community-list

To display Multiprotocol Border Gateway Protocol (MBGP) routes that match a community list, use the show ip mbgp community-list command.

show ip mbgp community-list commlist-name [exact-match] [vrf vrf-name]

Syntax Description

commlist-name	Name of a community-list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a community list:

switch(config)# show ip mbgp community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip mbgp dampening

To display Multiprotocol Border Gateway Protocol (MBGP) dampening information, use the show ip mbgp dampening command.

show ip mbgp dampening {dampened-paths [regexp expression] | flap-statistics | history-paths [regexp expression] | parameters} [vrf vrf-name]

Syntax Description

ipv4	(Optional) Display MBGP information for IPv4 address family.
ipv6	(Optional) Display MBGP information for IPv4 address family.
unicast	Displays MBGP information for unicast address family.
multicast	Displays MBGP information for multicast address family.
all	(Optional) Display MBGP information for all address families.
dampened-paths	Display all dampened paths.
regexp expression	(Optional) Display information that matches the regular expression.
flap-statistics	Display flap statistics for routes.
history-paths	Display all history paths.
parameters	Display all dampening parameters.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays dampening information:

switch(config)# show ip mbgp dampening dampened-paths

show ip mbgp filter-list

To display Multiprotocol Border Gateway Protocol (MBGP) routes that match a filter list, use the show ip mbgp filter-list command.

show ip mbgp filter-list list-name [exact-match] [vrf vrf-name]

Syntax Description

list-name	Name of a filter-list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a filter list:

switch(config)# show ip mbgp filter-list test1

show ip mbgp flap-statistics

To display Multiprotocol Border Gateway Protocol (MBGP) flap statistics, use the show ip mbgp flap-statistics command.

show ip mbgp flap-statistics [prefix] [vrf vrf-name]

Syntax Description

prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the flap statistics:

switch(config)# show ip mbgp flap-statistics

show ip mbgp history-paths

To display Multiprotocol Border Gateway Protocol (MBGP) history paths, use the show ip mbgp history-paths command.

show ip mbgp history-paths [regexp expression] [vrf vrf-name]

Syntax Description

regexp expression	(Optional) Display information that matches the regular expression.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays BGP history path information:

switch(config)# show ip mbgp history-paths

show ip mbgp neighbors

To display Multiprotocol Border Gateway Protocol (MBGP) neighbors, use the show ip mbgp neighbors command.

show ip mbgp neighbors [addr | prefix] [vrf vrf-name]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
prefix	(Optional) IPv4 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the MBGP neighbors:

switch(config)# show ip mbgp neighbors

show ip mbgp nexthop

To display Multiprotocol Border Gateway Protocol (MBGP) next hop information, use the show ip mbgp nexthop command.

show ip mbgp nexthop addr [vrf vrf-name]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP next-hop information:

switch(config)# show ip mbgp nexthop 192.0.2.1

Related Commands

Command	Description
show ip bgp nexhop	Displays BGP information.

show ip mbgp nexthop-database

To display Multiprotocol Border Gateway Protocol (MBGP) next-hop database, use the show ip mbgp nexthop-database command.

show ip mbgp nexthop-database [vrf vrf-name]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays the BGP next-hop database:

switch(config)# show ip mbgp nexthop-database

Related Commands

Command	Description
show ip bgp nexhop-database	Displays BGP information.

show ip mbgp prefix-list

To display Multiprotocol Border Gateway Protocol (MBGP) routes that match a prefix list, use the show ip mbgp prefix-list command.

show ip mbgp prefix-list list-name [exact-match] [vrf vrf-name]

Syntax Description

list-name	Name of a prefix list. The commlist-name can be any case-sensitive alphanumeric string up to 64 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive alphanumeric string up to 64 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example displays routes that match a prefix list:

switch(config)# show ip mbgp prefix-list test1

Related Commands

Command	Description
show ip bgp prefix-list	Displays BGP routes that match a prefix list.

show ip ospf

To display general information about Open Shortest Path First (OSPF) routing instances, use the show ip ospf command.

show ip ospf [instance-tag] [vrf vrf-name]

Syntax Description

instance-tag	(Optional) Instance tag. Use this tag to display OSPF information about a specific OSPF instance. The instance-tag argument can be any alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf command to display information about one or more OSPF instances.

This command requires the Enterprise Services license.

Examples

The following example shows how to display information about one specific OSPF instance:

switch# show ip ospf 201

 Routing Process 201 with ID 192.0.2.15 vrf default

 Stateful High Availability enabled

 Graceful-restart is configured

  Notify period: 15, grace period: 60, state: Inactive

  Last graceful restart exit status: (null)

 Supports only single TOS(TOS0) routes

 Supports opaque LSA

 Reference Bandwidth is 40000 Mbps

 Initial SPF schedule delay 200.000 msecs,

  minimum inter SPF delay of 1000.000 msecs,

  maximum inter SPF delay of 5000.000 msecs

 Minimum hold time for Router LSA throttle 5000.000 ms

 Minimum hold time for Network LSA throttle 5000.000 ms

 Minimum LSA arrival 1000.000 msec

 Maximum paths to destination 8

 Number of external LSAs 0, checksum sum 0

 Number of opaque AS LSA 0, checksum sum 0

 Number of areas is 2, 2 normal, 0 stub, 0 nssa

 Number of active areas is 0, 0 normal, 0 stub, 0 nssa

   Area BACKBONE(0) (Inactive)

        Area has existed for 1w0d

        Interfaces in this area: 1 Active interfaces: 0

        No authentication available

        SPF calculation has run 3 times

         Last SPF ran for 0.000132s

        Area ranges are

        Number of LSAs: 0, checksum sum 0

   Area (10) (Inactive)

        Area has existed for 1w0d

        Interfaces in this area: 1 Active interfaces: 0

        No authentication available

        SPF calculation has run 3 times

         Last SPF ran for 0.000035s

        Area ranges are

        Number of LSAs: 0, checksum sum 0

Table 1-13 describes the significant fields shown in the display.

Table 1-13 show ip ospf Field Descriptions 

Field	Description
Routing Process...	OSPF instance tag and OSPF router ID.
Stateful High Availability	Status of stateful restart capability.
Graceful-restart	Status of graceful restart configuration.
grace period	Number of seconds that OSPF has to trigger a graceful restart.
Last graceful restart exit status	Exit status for last graceful restart.
Supports...	Number of types of service supported (Type 0 only).
Reference Bandwidth	Bandwidth used for cost calculation.
Initial SPF schedule delay	Delay time of SPF calculations.
Minimum LSA arrival	Minimum interval between link-state advertisements.
Number of...	Number and type of link-state advertisements that have been received.
Number of areas is...	Number and type of areas configured for the router.

show ip ospf border-routers

To display the Open Shortest Path First (OSPF) routing table entries to an Area Border Router (ABR) and Autonomous System Boundary Router (ASBR), use the show ip ospf border-routers command.

show ip ospf [instance-tag] [vrf vrf-name] border-routers

Syntax Description

instance-tag	(Optional) Instance tag. Use this tag to display OSPF information about a specific OSPF instance. The instance-tag argument can be any alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf border-routers command to display information on ABRs. and ASBRs.

This command requires the Enterprise Services license.

Examples

The following example shows how to display information about border routers:

switch# show ip ospf border-routers

OSPF Process ID p1, vrf default Internal Routing Table

Codes: i - Intra-area route, I - Inter-area route

i 40.40.40.40 [10], ABR, Area 0.0.0.0, SPF 71 via

             192.0.2.1, Ethernet2/1

i 60.60.60.60 [20], ABR, Area 0.0.0.0, SPF 71 via

             192.0.2.1, Ethernet2/1

i 40.40.40.40 [10], ABR, Area 0.0.0.1, SPF 71 via

             192.0.2.1, Ethernet2/2

i 60.60.60.60 [20], ABR, Area 0.0.0.1, SPF 71 via

             192.0.2.1, Ethernet2/2

Table 1-14 describes the significant fields shown in the display.

Table 1-14 show ip ospf border-routers Field Descriptions 

Field	Description
40.40.40.40	Router ID of the destination.
[10]	Cost of using this route.
ABR	Router type of the destination; the type is either an ABR, ASBR, or both.
Area	Area ID of the area from which this route is learned.
SPF 71	Internal number of the shortest path first (SPF) calculation that installs this route.
via 192.0.2.1	Next hop toward the destination.
Ethernet2/1	Interface type for the outgoing interface.

show ip ospf database

To display the Open Shortest Path First (OSPF) database for a specific router, use the show ip ospf database command.

show ip ospf [instance-tag] [vrf vrf-name] database [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database asbr-summary [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database database-summary

show ip ospf [instance-tag] [vrf vrf-name] database external [ext_tag value] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database network [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database nssa-external [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database opaque-area [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database opaque-as [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database opaque-link [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database router [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

show ip ospf [instance-tag] [vrf vrf-name] database summary [area-id] [link-state-id] [adv-router ip-address | self-originated] [detail]

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
area-id	(Optional) Area number used to define the particular area. Specify as either an IP address or a number from 0 to 4294967295.
link-state-id	(Optional) Portion of the Internet environment that is being described by the advertisement. The value entered depends on the advertisement's link-state type. Specify in the form of an IP address.
adv-router ip-address	(Optional) Displays all the link-state advertisements (LSAs) of the specified router.
self-originate	(Optional) Displays self-originated LSAs (from the local router).
asbr-summary	(Optional) Displays information about the autonomous system boundary router summary LSAs.
database-summary	(Optional) Displays each type of LSA for each area in the database, and the total number of LSAs.
external	(Optional) Displays information about the external LSAs.
ext_tag value	(Optional) Displays information based on an external tag. The range is from 1 to 4294967295.
network	(Optional) Displays information about the network LSAs.
nssa-external	(Optional) Displays information about the not-so-stubby area (NSSA) external LSAs.
opaque-area	(Optional) Displays information about the opaque area LSAs.
opaque-as	(Optional) Displays information about the opaque AS LSAs.
opaque-link	(Optional) Displays information about the opaque link-local LSAs.
router	(Optional) Displays information about the router LSAs.
summary	(Optional) Displays information about the summary LSAs.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the ip ospf database command to display information about different OSPF LSAs.

When the link state advertisement is describing a network, the link-state-id argument can take one of two forms:

•The network's IP address (such as Type 3 summary link advertisements and autonomous system external link advertisements).

•A derived address obtained from the link state ID. (Note that masking a network links advertisement's link state ID with the network's subnet mask yields the network's IP address.)

•When the link state advertisement is describing a router, the link state ID is always the described router's OSPF router ID.

•When an autonomous system external advertisement (LS Type = 5) is describing a default route, its link state ID is set to Default Destination (0.0.0.0).

This command requires the Enterprise Services license.

Examples

The following example shows how to display the OSPF database:

Router# show ip ospf database

OSPF Router with ID (50.50.50.50) (Process ID p1)

                Router Link States (Area 0)

Link ID         ADV Router      Age        Seq#       Checksum Link Count

40.40.40.40     40.40.40.40     930        0x80000004 0x2ea1   3

50.50.50.50     50.50.50.50     935        0x80000002 0x8b52   1

60.60.60.60     60.60.60.60     943        0x800003c5 0x9854   2

                Network Link States (Area 0)

Link ID         ADV Router      Age        Seq#       Checksum

209.165.201.3   60.60.60.60     944        0x80000001 0x7179

192.0.2.1       50.50.50.50     935        0x80000001 0x516a

                Summary Network Link States (Area 0)

Link ID         ADV Router      Age        Seq#       Checksum

209.165.201.1   40.40.40.40     929        0x80000001 0x2498

209.165.201.1   50.50.50.50     928        0x80000001 0x5b2f

209.165.201.1   60.60.60.60     1265       0x800003c3 0xf49b

192.0.2.0       40.40.40.40     943        0x80000001 0x53f3

192.0.2.0       50.50.50.50     935        0x80000001 0x26f8

192.0.2.0       60.60.60.60     930        0x80000001 0x7b51

Table 1-15 describes the significant fields shown in the display.

Table 1-15 show ip ospf database Field Descriptions 

Field	Description
Link ID	Router ID number.
ADV Router	Advertising router's ID.
Age	Link state age.
Seq#	Link state sequence number (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the link state advertisement.
Link count	Number of interfaces detected for the router.

The following example shows how to display a summary of autonomous system border routers:

Router# show ip ospf database asbr-summary

OSPF Router with id(192.168.239.66) (Process ID 300)

                Displaying Summary ASB Link States(Area 0.0.0.0)

	LS age: 1463

	Options: (No TOS-capability)

	LS Type: Summary Links(AS Boundary Router)

	Link State ID: 172.16.245.1 (AS Boundary Router address)

	Advertising Router: 172.16.241.5

	LS Seq Number: 80000072

	Checksum: 0x3548

	Length: 28

	Network Mask: 0.0.0.0 TOS: 0  Metric: 1

Table 1-16 describes the significant fields shown in the display.

Table 1-16 show ip ospf database asbr-summary Field Descriptions 

Field	Description
OSPF Router with id	Router ID number.
Process ID	OSPF process ID.
LS age	Link state age.
Options	Type of service options (Type 0 only).
LS Type	Link state type.
Link State ID	Link state ID (autonomous system boundary router).
Advertising Router	Advertising router's ID.
LS Seq Number	Link state sequence (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the link state advertisement.
Length	Length in bytes of the link state advertisement.
Network Mask	Network mask implemented.
TOS	Type of service.
Metric	Link state metric.

The following example shows how to display information about external links:

Router# show ip ospf database external

OSPF Router with id(192.168.239.66) (Autonomous system 300)

                   Displaying AS External Link States

LS age: 280

Options: (No TOS-capability)

LS Type: AS External Link

Link State ID: 10.105.0.0 (External Network Number)

Advertising Router: 172.16.70.6

LS Seq Number: 80000AFD

Checksum: 0xC3A

Length: 36

Network Mask: 255.255.0.0

     		Metric Type: 2 (Larger than any link state path)

     		TOS: 0

     		Metric: 1

     		Forward Address: 0.0.0.0

     		External Route Tag: 0

Table 1-17 describes the significant fields shown in the display.

Table 1-17 show ip ospf database external Field Descriptions 

Field	Description
OSPF Router with id	Router ID number.
Autonomous system	OSPF autonomous system number (OSPF process ID).
LS age	Link state age.
Options	Type of service options (Type 0 only).
LS Type	Link state type.
Link State ID	Link state ID (external network number).
Advertising Router	Advertising router's ID.
LS Seq Number	Link state sequence number (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the LSA.
Length	Length in bytes of the link state advertisement.
Network Mask	Network mask implemented.
Metric Type	External type.
TOS	Type of service.
Metric	Link state metric.
Forward Address	Forwarding address. Data traffic for the advertised destination will be forwarded to this address. If the forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the advertisement's originator.
External Route Tag	External route tag; a 32-bit field attached to each external route. This field is not used by the OSPF protocol itself.

The following example shows how to display a summary of the OSPF database:

Router# show ip ospf database database-summary

OSPF Router with ID (100.0.0.1) (Process ID 1)

Area 0 database summary

  LSA Type      Count    Delete   Maxage

  Router        3        0        0

  Network       0        0        0

  Summary Net   0        0        0

  Summary ASBR  0        0        0

  Type-7 Ext    0        0        0

    Self-originated Type-7  0

Opaque Link     0        0        0

  Opaque Area   0        0        0

  Subtotal      3        0        0

Process 1 database summary

  LSA Type      Count    Delete   Maxage

  Router        3        0        0

  Network       0        0        0

  Summary Net   0        0        0

  Summary ASBR  0        0        0

  Type-7 Ext    0        0        0

  Opaque Link   0        0        0

  Opaque Area   0        0        0

  Type-5 Ext    0        0        0

      Self-originated Type-5  200

Opaque AS       0        0        0

  Total       203        0        0

Table 1-18 describes the significant fields shown in the display.

Table 1-18 show ip ospf database database-summary Field Descriptions 

Field	Description
Area 0 database summary	Area number.
Count	Count of LSAs of the type identified in the first column.
Router	Number of router link state advertisements in that area.
Network	Number of network link state advertisements in that area.
Summary Net	Number of summary link state advertisements in that area.
Summary ASBR	Number of summary autonomous system boundary router (ASBR) link state advertisements in that area.
Type-7 Ext	Type-7 LSA count.
Self-originated Type-7	Self-originated Type-7 LSA.
Opaque Link	Type-9 LSA count.
Opaque Area	Type-10 LSA count.
Subtotal	Sum of LSAs for that area.
Delete	Number of link state advertisements that are marked "Deleted" in that area.
Maxage	Number of link state advertisements that are marked "Maxaged" in that area.
Process 1 database summary	Database summary for the process.
Count	Count of LSAs of the type identified in the first column.
Router	Number of router link state advertisements in that process.
Network	Number of network link state advertisements in that process.
Summary Net	Number of summary link state advertisements in that process.
Summary ASBR	Number of summary autonomous system boundary router (ASBR) link state advertisements in that process.
Type-7 Ext	Type-7 LSA count.
Opaque Link	Type-9 LSA count.
Opaque Area	Type-10 LSA count.
Type-5 Ext	Type-5 LSA count.
Self-Originated Type-5	Self-originated Type-5 LSA count.
Opaque AS	Type-11 LSA count.
Total	Sum of LSAs for that process.

show ip ospf interface

To display Open Shortest Path First (OSPF)-related interface information, use the show ip ospf interface command.

show ip ospf interface [instance-tag] [vrf vrf-name] [interface-type interface-number] [brief]

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.
brief	(Optional) Displays brief overview information for OSPF interfaces, states, addresses, masks, and areas on the router.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf interface command to display the OSPF status for the interface.

This command requires the Enterprise Services license.

Examples

The following example shows how to display OSPF information for Ethernet interface 1/2:

switch# show ip ospf interface ethernet 1/2

Ethernet1/2 is up, line protocol is up

   IP address 192.0.2.1, Process ID 201 vrf default, area 10

   State UP, Network type BROADCAST, cost 65535

   Index 2, Transmit delay 1 sec, Router Priority 1

   No designated router on this network

   No backup designated router on this network

   0 Neighbors, flooding to 0, adjacent with 0

   Timer intervals: Hello 10, Dead 40, Wait 40, Retransmit 5

   Simple authentication

   Number of link LSAs: 0, checksum sum 0

Table 1-19 describes the significant fields shown in the display.

Table 1-19 show ip ospf interface Field Descriptions 

Field	Description
Ethernet	Status of physical link and operational status of protocol.
IP Address	Interface IP address, subnet mask, and area address.
vrf	Virtual routing and forwarding (VRF) instance.
Transmit Delay	Transmit delay, interface state, and router priority.
designated router	Designated router ID and interface IP address.
backup designated router	Backup designated router ID and interface IP address.
Timer intervals	Configuration of timer intervals.
Hello	Number of seconds until next hello packet is sent out this interface.

show ip ospf lsa-content-changed-list

To display a list of all link-state advertisements (LSAs) with changed content, use the show ip ospf lsa-content-changed-list command.

show ip ospf lsa-content-changed-list neighbor-id interface-type interface-number

Syntax Description

neighbor id	Router ID for the neighbor.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

The following example shows how to display a list of LSAs that changed for Ethernet 2/1:

Router# show ip ospf lsa-content-changed-list 192.0.2.2 ethernet 2/1 

Table 1-21 describes the significant fields shown in the displays.

Table 1-20 show ip ospf lsa-content-changed-list Field Descriptions 

Field	Description

show ip ospf memory

To display the memory usage statistics for the Open Shortest Path First (OSPF) protocol, use the show ip ospf memory command.

show ip ospf memory

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(3)	This command was removed.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

The following example shows how to display the memory statistics for OSPF:

Router# show ip ospf memory 

 OSPF Process ID sd, Memory statistics

  Process memory: 2096 KB

  Byte usage:    needed 0, overhead 192, using 192 bytes

  Allocations:   current 6, created 6, failed 0, free 0

  Bitfields:     current 30, created 30, failed 0, free 0, using 248010 bytes

  Slabs:         current 2, created 2, failed 0, free 0, using 80 bytes

  Index failure: Interface 0, Neighbor 0

  Slab Memory

  OSPF vertex slab

  Alloc 1, max allocs 1, total allocs 1, total frees 0

  Total block allocs 1, total block frees 0, max blocks 1

  Bytes (size/allocated) 68/69720

  OSPF IPv4 prefix routes slab

  Alloc 0, max allocs 0, total allocs 0, total frees 0

  Total block allocs 0, total block frees 0, max blocks 0

  Bytes (size/allocated) 188/64

  OSPF router routes slab

  Alloc 0, max allocs 0, total allocs 0, total frees 0

  Total block allocs 0, total block frees 0, max blocks 0

  Bytes (size/allocated) 100/64

  OSPF IPv4 next-hops slab

  Alloc 1, max allocs 1, total allocs 1, total frees 0

  Total block allocs 1, total block frees 0, max blocks 1

  Bytes (size/allocated) 32/262232

show ip ospf neighbors

To display Open Shortest Path First (OSPF)-neighbor information on a per-interface basis, use the show ip ospf neighbor command.

show ip ospf [instance-tag] [vrf vrf-name] neighbors [interface-type interface-number] [neighbor-id] [detail] [summary]

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
area-id	(Optional) Area number used to define the particular area. Specify as an IP address or a number from 0 to 4294967295.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.
neighbor-id	(Optional) Router ID of the neighbor. Specify as an IP address.
detail	(Optional) Displays all neighbors given in detail (lists all neighbors).
summary	(Optional) Displays a summary of the neighbors.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf neighbors command to display information about all or some of the neighbors for this OSPF instance.

This command requires the Enterprise Services license.

Examples

The following example shows how to display the summary information about the neighbor that matches the neighbor ID:

Router# show ip ospf neighbors 10.199.199.137

Neighbor 10.199.199.137, interface address 192.0.2.37

    In the area 0.0.0.0 via interface Ethernet2/1

    Neighbor priority is 1, State is FULL

    Options 2

    Dead timer due in 0:00:32

    Link State retransmission due in 0:00:04

 Neighbor 10.199.199.137, interface address 209.165.201.189

    In the area 0.0.0.0 via interface Ethernet4/3

    Neighbor priority is 5, State is FULL

    Options 2

    Dead timer due in 0:00:32

    Link State retransmission due in 0:00:03

The following example shows how to display the neighbors that match the neighbor ID on an interface:

Router# show ip ospf neighbors ethernet 2/1 10.199.199.137

Neighbor 10.199.199.137, interface address 192.0.2.37

    In the area 0.0.0.0 via interface Ethernet2/1

    Neighbor priority is 1, State is FULL

    Options 2

    Dead timer due in 0:00:37

    Link State retransmission due in 0:00:04

The following example shows how to display detailed information about OSPF neighbors:

Router# show ip ospf neighbors detail

Neighbor 192.168.5.2, interface address 10.225.200.28

    In the area 0 via interface GigabitEthernet1/0/0

    Neighbor priority is 1, State is FULL, 6 state changes

    DR is 10.225.200.28 BDR is 10.225.200.30

    Options is 0x42

    LLS Options is 0x1 (LR), last OOB-Resync 00:03:08 ago

    Dead timer due in 00:00:36

    Neighbor is up for 00:09:46

   Index 1/1, retransmission queue length 0, number of retransmission 1

    First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)

    Last retransmission scan length is 1, maximum is 1

    Last retransmission scan time is 0 msec, maximum is 0 msec

Table 1-21 describes the significant fields shown in the displays.

Table 1-21 show ip ospf neighbor detail Field Descriptions 

Field	Description
Neighbor	Neighbor router ID.
interface address	IP address of the interface.
In the area	Area and interface through which the OSPF neighbor is known.
Neighbor priority	Router priority of the neighbor.
State	OSPF state.
state changes	Number of state changes since the neighbor was created.This value can be reset using the clear ip ospf counters neighbor command.
DR is	Router ID of the designated router for the interface.
BDR is	Router ID of the backup designated router for the interface.
Options	Hello packet options field contents. (E-bit only. Possible values are 0 and 2; 2 indicates the area is not a stub; 0 indicates the area is a stub.)
LLS Options..., last OOB-Resync	Link-Local Signalling and out-of-band (OOB) link-state database resynchronization performed hours:minutes:seconds ago (NSF information). The field indicates the last successful out-of-band resynchronization with the NSF-capable router.
Dead timer due in	Expected time before Cisco NX-OS declares the neighbor dead.
Neighbor is up for	Number of hours:minutes:seconds since the neighbor went into a two-way state.
Index	Neighbor location in the area-wide and autonomous system-wide retransmission queue.
retransmission queue length	Number of elements in the retransmission queue.
number of retransmission	Number of times that update packets have been resent during flooding.
First	First memory location of the flooding details.
Next	Next memory location of the flooding details.
Last retransmission scan length	Number of link state advertisements (LSAs) in the last retransmission packet.
maximum	Maximum number of LSAs sent in any retransmission packet.
Last retransmission scan time	Time taken to build last retransmission packet.
maximum	Maximum time taken to build any retransmission packet.

show ip ospf policy statistics area

To display Open Shortest Path First (OSPF) policy statistics for an area, use the show ip ospf policy statistics area command.

show ip ospf [instance-tag] [vrf vrf-name] policy statistics area area id filter-list {in | out}

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
area area-id	Specifies the area number used to define the particular area. Specify as an IP address or a number from 0 to 4294967295.
filter-list	Filters prefixes between OSPF areas.
in	Displays policy statistics for incoming routes.
out	Displays policy statistics for outgoing routes.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf policy statistics area command to display information about the filter lists applied to an area.

This command requires the Enterprise Services license.

Examples

The following example shows how to display policy statistics for OSPF:

switch# show ip ospf policy statistics area 201

show ip ospf policy statistics redistribute

To display Open Shortest Path First (OSPF) policy statistics, use the show ip ospf policy statistics redistribute command.

show ip ospf [instance-tag] [vrf vrf-name] policy statistics redistribute {bgp id | direct | eigrp id | isis id | ospf id | rip id | static}

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP).
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for OSPF.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an autonomous system number. The range is from 1 to 65535. For the isis. ospf, and rip keywords, an instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf policy statistics redistribute command to display redistribution statistics.

This command requires the Enterprise Services license.

Examples

The following example shows how to display policy statistics for redistributed routes:

switch# show ip ospf policy statistics redistribute

show ip ospf request-list

To display a list of all link-state advertisements (LSAs) requested by a router, use the show ip ospf request-list command.

show ip ospf request-list neighbor-id interface interface-number

Syntax Description

neighbor-id	Router ID of the neighbor. Specify as an IP address.
interface-type	Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf request-list command to troubleshoot Open Shortest Path First (OSPF) routing operations.

This command requires the Enterprise Services license.

Examples

The following example shows how to display a list of all LSAs requested by a router:

Router# show ip ospf request-list 40.40.40 ethernet 2/1

 OSPF Process ID p1

 Neighbor 40.40.40.40, interface Ethernet2/1, address 192.0.2.1

 1 LSAs on request-list

  Type  LS ID           ADV RTR          Seq NO      Age    Checksum

   1  192.0.2.12      192.0.2.12          0x8000020D  8      0x6572

Table 1-22 describes the significant fields shown in the displays.

Table 1-22 show ip ospf request-list Field Descriptions 

Field	Description
Type	LSA type.
LS ID	IP address of the neighbor router.
ADV RTR	IP address of the advertising router.
Seq NO	Packet sequence number of the LSA.
Age	Age, in seconds, of the LSA.
Checksum	Checksum number of the LSA.

show ip ospf retransmission-list

To display a list of all link-state advertisements (LSAs) waiting to