Table Of Contents
show diagnostic description module
show diagnostic ondemand setting
show event manager environment
show event manager event-types
show event manager history events
show event manager policy-state
show event manager system-policy
show hardware fabric-utilization
show hardware flow utilization
show logging ip access-list cache
Show Commands
This chapter describes the Cisco NX-OS system management show commands.
show checkpoint
To display the contents of the checkpoint file, use the show checkpoint command.
show checkpoint [name]
Syntax Description
name
(Optional) Name of the checkpoint file. The name can be any alphanumeric string up to 63 characters.
Defaults
None
Command Modes
Configuration mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the contents of the checkpoint file:
switch# show checkpoint stable
--------------------------------------------------------
Name: stableversion 4.0(2)power redundancy-mode combined forcelicense grace-periodfeature vrrpfeature tacacs+feature ospffeature pimfeature pim6feature msdpfeature eigrpfeature ripfeature isisfeature pbrfeature private-vlanfeature port-security
feature interface-vlanfeature dot1xfeature hsrpfeature lacpfeature glbp
feature dhcpfeature ctslogging level port-security 5logging level glbp 6snmp-server context foosnmp-server community <removed> group vdc-operatorsnmp-server community <removed> group network-adminsnmp-server community <removed> group vdc-adminrole feature-group name Xrole feature-group name xrole name xvlan policy denyvrf policy denypermit vrf xpermit vrf Xrole name Xusername adminbackup password 5 $1$Oip/C5Ci$oOdx7oJSlBCFpNRmQK4na. role vdc-operatorusername adminbackup role network-operatorusername admin password 5 $1$8GYeC4uW$4WfnImcvtAKI6Uet.ePD.1 role network-adminRelated Commands
show configuration session
To show information about the configuration sessions, use the show configuration session command.
show configuration session [name] [status] [summary]
Syntax Description
Defaults
Display information for all sessions
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about a configuration session. Each line represents a CLI command that Cisco NX-OS applies to the device when you commit the session.
switch# show configuration session myACLsconfig session name myACLs0001 ip access-list test10002 permit tcp any any0003 statisticsThis example shows how to display the status of a configuration session:
switch(config-s)# show configuration session statusSession Name : myACLSLast Action : NoneLast Action Status : SuccessLast Action Reason : -NA-Last Action Timestamp : 00:00:00 UTC Jan 01 1970This example shows how to display a summary of the configuration sessions:
switch(config-s)# show configuration session summaryName Session Owner Creation Time--------------------------------------------------------------------myACLS admin 21:34:39 UTC Apr 27 2008status admin 00:53:23 UTC Apr 29 2008a admin 01:47:30 UTC Apr 28 2008myACLs admin 00:56:46 UTC Apr 29 2008Number of active configuration sessions = 4switch(config-s)#Related Commands
show tech-support session-mgr
Shows detailed information about the configuration sessions for troubleshooting purposes.
show diagnostic bootup level
To display information about bootup diagnostics, use the show diagnostic bootup level command.
show diagnostic bootup level
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the bootup diagnostic level:
switch# show diagnostic bootup levelCurrent bootup diagnostic level: completeswitch#
Related Commands
show diagnostic content
To display information about the diagnostic test content for a module, use the show diagnostic content command.
show diagnostic content {number | all}
Syntax Description
number
Diagnostic content module number. The range is from 1 to 10.
all
Displays the test content for all tests on all modules.
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show diagnostic content command to display information about the tests configured on the module and the repeat interval time.
Examples
This example shows how to display information about the diagnostic test content for a module:
switch# show diagnostic content module 6Module 6: Supervisor module-1X (Active)Diagnostics test suite attributes:B/C/* - Bypass bootup level test / Complete bootup level test / NAP/* - Per port test / NAS/* - Only applicable to standby unit / NAD/N/* - Disruptive test / Non-disruptive test / NAH/* - Always enabled monitoring test / NAF/* - Fixed monitoring interval test / NAX/* - Not a health monitoring test / NAE/* - Sup to line card test / NAL/* - Exclusively run this test / NAT/* - Not an ondemand test / NAA/I/* - Monitoring is active / Monitoring is inactive / NATesting IntervalID Name Attributes (hh:mm:ss)____ __________________________________ ____________ _________________1) ManagementPortLoopback--------> C**D**X**T* -NA-2) EOBCPortLoopback--------------> C**D**X**T* -NA-3) ASICRegisterCheck-------------> ***N******A 00:00:204) USB---------------------------> C**N**X**T* -NA-5) CryptoDevice------------------> C**N**X**T* -NA-6) NVRAM-------------------------> ***N******A 00:00:307) RealTimeClock-----------------> ***N******A 00:05:008) PrimaryBootROM----------------> ***N******A 00:30:009) SecondaryBootROM--------------> ***N******A 00:30:0010) CompactFlash------------------> ***N******A 00:30:0011) ExternalCompactFlash----------> ***N******A 00:30:0012) PwrMgmtBus--------------------> ***N******A 00:00:3013) SpineControlBus---------------> ***N******A 00:00:3014) SystemMgmtBus-----------------> ***N******A 00:00:30switchshow diagnostic description module
To display information about a diagnostic test for a module, use the show diagnostic description nodule command.
show diagnostic description module slot test {test-ID | test-name | all}
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a diagnostic description for a module:
switch# show diagnostic description module 6 test 1ManagementPortLoopback :A bootup test that tests loopback on the management port ofthe moduleRelated Commands
show diagnostic ondemand setting
To display information about the ondemand diagnostic test for a module, use the show diagnostic ondemand setting command.
show diagnostic ondemand setting
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display diagnostic ondemand information:
switch# show diagnostic ondemand settingTest iterations = 1Action on test failure = continue until test failure limit reaches 1Related Commands
show diagnostic result
To display diagnostic test result for a module, use the show diagnostic result command.
show diagnostic result module {slot [test [test-id | test-name]] | all} [detail]
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display a diagnostic test result:
switch# show diagnostic result module 6 test 6 detailCurrent bootup diagnostic level: completeModule 6: Supervisor module-1X (Active)Diagnostic level at card bootup: completeTest results: (. = Pass, F = Fail, I = Incomplete,U = Untested, A = Abort, E = Error disabled)______________________________________________________________________6) NVRAM-------------------------> .Error code ------------------> DIAG TEST SUCCESSTotal run count -------------> 1574Last test execution time ----> Thu Jun 26 09:28:40 2008First test failure time -----> n/aLast test failure time ------> n/aLast test pass time ---------> Thu Jun 26 09:28:41 2008Total failure count ---------> 0Consecutive failure count ---> 0Last failure reason ---------> No failures yetswitch#show diagnostic simulation
To display information about a simulated diagnostic for a module, use the show diagnostic simulation command.
show diagnostic simulation module slot
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about simulated diagnostics:
switch# show diagnostic simulation module 6Card(6): Supervisor module-1X________________________________________________-NA-switch#Related Commands
show diagnostic status
To display the test status for all tests, use the show diagnostic status command.
show diagnostic status module slot
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the test status for all tests on a module:
switch# show diagnostic status module 6<BU>-Bootup Diagnostics, <HM>-Health Monitoring Diagnostics<OD>-OnDemand Diagnostics, <SCH>-Scheduled Diagnostics==============================================Card:(6) Supervisor module-1X==============================================Current running test Run by-NA- -NA-Currently Enqueued Test Run by-NA- -NA-switch#show diff rollback-patch
To display the differences between the source and destination, use the show diff rollback-patch command.
show diff rollback-patch {checkpoint name | running-config | startup-config} {checkpoint name | running-config | startup-config}
Syntax Description
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the differences between the stable checkpoint file and the running configuration.
switch# show diff rollback-patch checkpoint stable running-configswitch#Related Commands
show checkpoint
Displays the contents of the checkpoint file.
rollback running checkpoint
Implements a rollback for the configured checkpoint file.
show environment
To display information about the hardware environment status, use the show environment command.
show environment [clock | fan | power | temperature]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
You can use this command to display information about the status of the hardware on your device.
This command does not require a license.
Examples
This example shows how to display information about the hardware environment:
switch# show environmentClock:----------------------------------------------------------Clock Model Hw Status----------------------------------------------------------A Clock Module -- NotSupported/NoneB Clock Module -- NotSupported/NoneFan:------------------------------------------------------Fan Model Hw Status------------------------------------------------------Fan1(sys_fan1) 0.0 OkFan2(sys_fan2) 0.0 OkFan3(fab_fan1) 0.0 OkFan4(fab_fan2) 0.0 OkFan_in_PS1 -- -- OkFan_in_PS2 -- -- OkFan_in_PS3 -- -- AbsentFan Air Filter : AbsentTemperature:--------------------------------------------------------------------Module Sensor MajorThresh MinorThres CurTemp Status(Celsius) (Celsius) (Celsius)--------------------------------------------------------------------2 Crossbar(s5) 105 95 40 Ok2 CTSdev1 (s6) 115 105 47 Ok2 CTSdev2 (s7) 115 105 51 Ok2 CTSdev3 (s8) 115 105 47 Ok2 CTSdev4 (s9) 115 105 48 Ok2 CTSdev5 (s10) 115 105 47 Ok2 CTSdev7 (s12) 115 105 50 Ok2 CTSdev8 (s13) 115 105 50 Ok2 CTSdev9 (s14) 115 105 48 Ok2 CTSdev10(s15) 115 105 48 Ok2 CTSdev11(s16) 115 105 46 Ok2 CTSdev12(s17) 115 105 45 Ok2 QEng1Sn1(s18) 115 105 43 Ok2 QEng1Sn2(s19) 115 105 42 Ok2 QEng1Sn3(s20) 115 105 39 Ok2 QEng1Sn4(s21) 115 105 40 Ok2 L2Lookup(s22) 115 105 43 Ok2 L3Lookup(s23) 120 110 54 OkPower Supply:Voltage: 50 Volts-----------------------------------------------------PS Model Power Power Status(Watts) (Amp)-----------------------------------------------------1 N7K-AC-6.0KW 0.00 0.00 Ok2 N7K-AC-6.0KW 6000.00 120.00 Ok3 ------------ 0.00 0.00 AbsentMod Model Power Power Power Power StatusRequested Requested Allocated Allocated(Watts) (Amp) (Watts) (Amp)--- ------------------- ------- ---------- --------- ---------- ----------2 N7K-M148GT-11 247.00 4.94 247.00 4.94 Powered-Up6 N7K-SUP1 210.00 4.20 210.00 4.20 Powered-UpXb1 N7K-C7010-FAB-1 123.50 2.47 123.50 2.47 Powered-UpPower Usage Summary:--------------------Power Supply redundancy mode: Non-Redundant(combined)Power Supply redundancy operational mode: Non-Redundant(combined)Total Power Capacity 6000.00 WPower reserved for Supervisor(s) 420.00 WPower reserved for Fan Module(s) 2184.00 WPower reserved for Fabric Module(s) 300.00 WPower currently used by Modules 247.00 W-------------Total Power Available 2849.00 W-------------This example shows how to display information about the power environment:
switch# show environment powerPower Supply:Voltage: 50 Volts-----------------------------------------------------PS Model Power Power Status(Watts) (Amp)-----------------------------------------------------1 FIORANO 0.00 0.00 Ok2 FIORANO 6000.00 120.00 Ok3 ------------ 0.00 0.00 AbsentMod Model Power Power Power Power StatusRequested Requested Allocated Allocated(Watts) (Amp) (Watts) (Amp)--- ------------------- ------- ---------- --------- ---------- ----------2 NURBURGRING 247.00 4.94 247.00 4.94 Powered-Up6 CATALUNYA 210.00 4.20 210.00 4.20 Powered-UpXb1 Estoril 123.50 2.47 123.50 2.47 Powered-UpPower Usage Summary:--------------------Power Supply redundancy mode: Non-Redundant(combined)Power Supply redundancy operational mode: Non-Redundant(combined)Total Power Capacity 6000.00 WPower reserved for Supervisor(s) 420.00 WPower reserved for Fan Module(s) 2184.00 WPower reserved for Fabric Module(s) 300.00 WPower currently used by Modules 247.00 W-------------Total Power Available 2849.00 W-------------Related Commands
show event manager environment
Use the show event manager environment command to display the name and value of Embedded Event Manager (EEM) environment variables.
show event manager environment {varname | all}
Syntax Description
{varname | all}
Displays information about the specified environment variable or all environment variables.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows all of the EEM environment variables:
switch# show event manager environment allswitch#show event manager event-types
Use the show event manager event-types command to view the Embedded Event Manager (EEM) event types.
show event manager event-types [detail | event-type-name] [module module]
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the details of the EEM event types:
switch# show event manager event-types detailswitch#show event manager history events
Use the show event manager history events command to display the Embedded Event Manager (EEM) events that have been triggered.
show event manager history events [detail] [maximum number] [severity severity]
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the EEM history events that have been triggered that were of severity 7:
switch# show event manager history events severity 7switch#show event manager policy
Use the show event manager policy command to view the registered Embedded Event Manager (EEM) policies.
show event manager policy [detail] [policy-name | inactive]
Syntax Description
detail
(Optional) View details of all policies.
policy-name
(Optional) Specify a policy-name policy to display.
inactive
(Optional) View only those policies that are inactive.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the EEM policies:
switch# show event manager policyswitch#show event manager policy-state
Use the show event manager policy-state command to view the state of the named Embedded Event Manager (EEM) policy.
show event manager policy-state name [module module]
Syntax Description
name
Specify the name of a policy to display its state.
module module
(Optional) View the policy state defined for a specific module. Select from module 1 to 10.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the state of an EEM policy:
switch# show event manager policy-state policy42switch#show event manager script
Use the show event manager script command to view the script policy of the Embedded Event Manager (EEM).
show event manager script system {all | script-name}
Syntax Description
name
Specify the name of a policy to display its state.
module module
(Optional) View the policy state defined for a specific module. Select from module 1 to 10.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows all the system scripts defined in the EEM:
switch# show event manager script system allswitch#show event manager system-policy
Use the show event manager system-policy command to view the system policies of the Embedded Event Manager (EEM).
show event manager system-policy [all]
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the EEM system policies:
switch# show event manager system-policyswitch#Related Commands
show flow exporter
To display Flexible NetFlow flow exporter status and statistics, use the show flow exporter command in Any mode.
show flow exporter [name exporter-name]
Syntax Description
name exporter-name
(Optional) Specifies the name of a flow exporter. The name can be any case-sensitive alphanumeric string up to 64 characters.
Command Default
Information for all flow exporters configured on the router is displayed.
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
This command does not require a license.
Examples
The following example displays the status and statistics for all of the flow exporters configured on the router:
switch# show flow exporterFlow Exporter NFC-DC-PHOENIX:Export Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverFlow exporter timeout:Export Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverFlow exporter test-exporter:Description: test server in San Jose CAExport Version 5Exporter StatisticsNumber of Flow Records Exported 0Number of Export Packets Sent 0Number of Export Bytes Sent 0Number of Destination Unreachable Events 0Number of No Buffer Events 0Number of Packets Dropped (No Route to Host) 0Number of Packets Dropped (other) 0Number of Packets Dropped (LC to RP Error) 0Number of Packets Dropped (Output Drops) 0Time statistics were last cleared: NeverThe output fields are self explanatory.
Related Commands
show flow interface
To display the Flexible NetFlow configuration and status for an interface, use the show flow interface command in Any mode.
show flow interface [interface-type number]
Syntax Description
interface-type number
(Optional) The type of interface that you want to view Flexible NetFlow accounting configuration information on.
Command Default
Information for the Flexible NetFlow accounting configuration on the interface is displayed.
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show flow interface command.
This command does not require a license.
Examples
The following example displays the Flexible NetFlow accounting configuration on interface Ethernet 0/0 and 0/1:
switch# show flow interface ethernet 1/0Interface Ethernet1/0FNF: monitor: NFC-DC-PHOENIXdirection: Outputtraffic(ip): onswitch# show flow interface ethernet 0/0Interface Ethernet0/0FNF: monitor: FLOW-MONITOR-1direction: Inputtraffic(ip): sampler SAMPLER-2#Table 1 describes the significant fields shown in the display.
Related Commands
show flow monitor
To display the status and statistics for a Flexible NetFlow flow monitor, use the show flow monitor command in Any mode.]
show flow monitor [name exporter-name]
Syntax Description
name exporter-name
(Optional) Specifies the name of a flow exporter. The name can be any case-sensitive alphanumeric string up to 64 characters.
Command Default
Information for all flow exporters configured on the router is displayed.
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
This command does not require a license.
Examples
The following example displays the status and statistics for a flow monitor:
switch# show flow monitor NFC-DC-PHOENIX statisticsCache type: NormalCache size: 4096Current entries: 4High Watermark: 6Flows added: 116Flows aged: 112- Active timeout ( 1800 secs) 0- Inactive timeout ( 15 secs) 112- Event aged 0- Watermark aged 0- Emergency aged 0Table 2 describes the significant fields shown in the display.
The following example displays the status for a flow monitor:
switch# show flow monitor NFC-DC-PHOENIXFlow Monitor NFC-DC-PHOENIX:Description: Used for basic traffic analysisFlow Record: netflow-originalFlow Exporter: EXP-DC-TOPEKAEXP-DC-PHOENIXCache:Type: normalStatus: allocatedSize: 4096 entries / 311316 bytesInactive Timeout: 15 secsActive Timeout: 1800 secsUpdate Timeout: 1800 secsTable 3 describes the significant fields shown in the display.
The following example displays the status and statistics for the flow monitor named NFC-DC-PHOENIX:
switch# show flow monitor NFC-DC-PHOENIX cacheCache type: NormalCache size: 4096Current entries: 8High Watermark: 10Flows added: 1560Flows aged: 1552- Active timeout ( 1800 secs) 24- Inactive timeout ( 15 secs) 1528- Event aged 0- Watermark aged 0- Emergency aged 0IP TOS: 0x00IP PROTOCOL: 6IPV4 SOURCE ADDRESS: 10.10.10.2IPV4 DESTINATION ADDRESS: 172.16.10.2TRNS SOURCE PORT: 20TRNS DESTINATION PORT: 20INTERFACE INPUT: Et0/0FLOW SAMPLER ID: 0ip source as: 0ip destination as: 0ipv4 next hop address: 172.16.7.2ipv4 source mask: /0ipv4 destination mask: /24tcp flags: 0x00interface output: Et1/0counter bytes: 198520counter packets: 4963timestamp first: 10564356timestamp last: 12154104Table 4 describes the significant fields shown in the display.
The following example displays the status and statistics the flow monitor named NFC-DC-PHOENIX in a table format:
switch# show flow monitor NFC-DC-PHOENIX cache format tableCache type: NormalCache size: 4096Current entries: 4High Watermark: 6Flows added: 90Flows aged: 86- Active timeout ( 1800 secs) 0- Inactive timeout ( 15 secs) 86- Event aged 0- Watermark aged 0- Emergency aged 0IP TOS IP PROT IPV4 SRC ADDR IPV4 DST ADDR TRNS SRC PORT TRNS DST PORT====== ======= =============== =============== ============= ==============0x00 1 10.251.10.1 172.16.10.2 0 020x00 1 10.251.10.1 172.16.10.2 0 204840xC0 17 172.16.6.1 224.0(1).0.9 520 52020x00 6 10.10.11.1 172.16.10.5 25 252switch#Related Commands
show flow record
To display the status and statistics for a Flexible NetFlow flow record, use the show flow record command.
show flow record [name record-name | netflow ipv4 record | netflow-original]
Syntax Description
name record-name
(Optional) Specifies name of a flow record that you previously configured.
netflow ipv4 record
(Optional) Configures the flow monitor to use one of the predefined records. See Table 5 for a listing of the available records and their definitions.
netflow-original
(Optional) Specifies the Flexible NetFlow implementation of original NetFlow with origin autonomous systems.
Command Default
Information for all flow exporters configured on the router is displayed.
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the show flow exporter command.
This command does not require a license.
Table 5 describes the keywords and descriptions for the record argument.
Table 5 Keywords and Descriptions for the record Argument
original-input
Traditional IPv4 input NetFlow.
original-output
Traditional IPv4 output NetFlow.
protocol-port
Protocol Ports record.
Examples
The following example displays the status and statistics the original input NetFlow record:
switch# show flow record netflow ipv4 original-inputFlow record ipv4 original-input:Description: Traditional IPv4 input NetFlowNo. of users: 0Template ID: 0Fields:match ipv4 source addressmatch ipv4 destination addressmatch ip protocolmatch ip tosmatch transport source-portmatch transport destination-portmatch interface inputcollect routing source ascollect routing destination ascollect routing next-hop address ipv4collect transport tcp flagscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime lastcollect interface outputswitch#Table 6 describes the significant fields shown in the display.
Related Commands
show flow timeout
To display the Flexible NetFlow flow cache timeout values, use the show flow timeout command in Any mode.
show flow timeout
Syntax Description
This command has no arguments or keywords.
Command Default
Information for the Flexible NetFlow accounting configuration on the interface is displayed.
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show flow timeout command.
This command does not require a license.
Examples
The following example displays the Flexible NetFlow flow cache timeout values:
switch# show flow timeoutFlow timeout valuesActive timeout: 1800 secondsInactive timeout: 15 secondsFast timeout: DisabledSession aging timeout: DisabledAggressive aging timeout: Disabledswitch#The fields in the output are self explanatory.
Related Commands
show hardware fabric-utilization
To display information fabric utilization, use the show hardware fabric-utilization command.
show hardware fabric-utilization [detail] [module slot-number]
Syntax Description
detail
(Optional) Displays detailed information about the fabric utilization.
module slot-number
(Optional) Displays information specific to a module.
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example displays the fabric utilization:
switch(config)# show hardware fabric-utilization-----------------------------Slot Direction Utilization-----------------------------2 ingress 3%2 egress 3%6 ingress 1%6 egress 1%The fields in the output are self explanatory.
show hardware flow aging
To display information about NetFlow hardware flow aging, use the show hardware flow aging command.
show hardware flow aging [vdc vdc-name] [detail] [module slot-number]
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow aging command.
This command does not require a license.
Examples
This example displays the NetFlow aging values for module 2:
switch(config)# show hardware flow aging module 2VDC(1) Aging Information (time unit is second):AgingType Enabled Timeout Period Threshold----------+----------+----------+----------+----------Active Yes 1800 360 N/AInactive Yes 15 3 N/AFast Yes 33 6 22Aggressive No 90 18 90Session No 2 5 N/Aswitch(config)#The fields in the output are self explanatory.
Related Commands
show hardware flow entry
To display information about NetFlow table entry, use the show hardware flow entry command.
show hardware flow entry address location type {ip | ipv6} [detail] [module slot-number]
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow entry command.
This command does not require a license.
Examples
This example displays the NetFlow table entry for module 2:
switch(config)# show hardware flow entry address 0x0 type ip module 2NT Entry Info (dev_id = 0, nt_entry_addr = 0x00000000):protocol = 0 (0=IPv4/IPMAC, 1=IPv6, 2=L2, 3=MPLS)profile_id = 0recir_id = 0is_routed = 0from_rp = 0lkup_dir = 0 (0=Ingress, 1=Egress)ilif(ovld_a) = 0x0elif(ovld_b) = 0x0tos(ovld_e) = 0l4_protocol = 0l4_hdr_vld = 0fragment = 0mpls = 0l4_info(ovld_d) = 0x00000000ipv4_sa(ovld_f) = 0.0.0.0ipv4_da(ovld_g) = 0.0.0.0ipmac = 0segment = 0hash_addr = 0x0icam = 0create_ts = 0sh_plc_idx/sampler_id = 0x0rdt_tbl_idx = 0x0ignr_aclo = 0ignr_qoso = 0ignr_acc = 0ignr_agg_qos = 0tcp_rdt_dst = 0copy_policy_idx = 0x0nf_acos = 0mark_en = 0nf_qos_mode = 0policer_param_idx = 0x0elam_trig = 0valid = 0sw_entry = 0profile_merged = 0fast_ag_en = 0sw_bits1 = 0dgt_mode = 0adj_ptr/dgt = 0x0ignr_qosi = 0ignr_acli = 0NS Entry Info (dev_id = 0, ns_entry_addr = 0x00000000):ack_after_fin = 0tcp_flag = 0x0 (URG=0, ACK=0, PSH=0, RST=0, SYN=0, FIN=0)mf_ls_ts = 0mf_bkt = 0nf_pkt_cnt = 0000000000nf_byte_cnt = 0000000000000nf_byte_cnt_excd = 0000000000000ls_used_ts = 0sw_prog/sticky_status = 0Related Commands
show hardware flow ip
To display information about NetFlow hardware IP flows, use the show hardware flow ip command.
show hardware flow ip [interface type number | monitor monitor-name | profile profile-id | vdc vdc-name | vlan vlan-name] [detail] [module module]
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow ip command.
This command does not require a license.
Examples
This example displays the NetFlow aging values for module 8:
switch(config)# show hardware flow ip module 8D - Direction; L4 Info - Protocol:Source Port:Destination PortIF - Interface: ()ethernet, (S)vi, (V)lan, (P)ortchannel, (T)unnelTCP Flags: Ack, Flush, Push, Reset, Syn, UrgentD IF SrcAddr DstAddr L4 Info PktCnt TCP Flags-+-----+---------------+---------------+---------------+----------+-----------I 8/26 007.002.000.002 007.001.000.002 000:00000:00000 0000421885 . . . . . .I 8/25 007.001.000.002 007.002.000.002 000:00000:00000 0000421900 . . . . . .O 8/25 007.002.000.002 007.001.000.002 000:00000:00000 0000422213 . . . . . .O 8/26 007.001.000.002 007.002.000.002 000:00000:00000 0000422228 . . . . . .switch(config)#Related Commands
show hardware flow sampler
To display information about sampled NetFlow hardware flows, use the show hardware flow sampler command.
show hardware flow sampler [all | count | index number | name sampler-name | vdc vdc_id] [detail] [module module]
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow sampler command.
This command does not require a license.
Examples
This example displays the NetFlow sampler table utilization for module 2:
switch# show hardware flow sampler count module 2Sampler Table Utilization: about 0.00% (0/64)Related Commands
show hardware flow utilization
To display information about NetFlow hardware flow utilization, use the show hardware flow utilization command.
show hardware flow utilization [module module]
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must have already enabled traffic monitoring with Flexible NetFlow before you can use the show hardware flow utilization command.
This command does not require a license.
Examples
This example displays the NetFlow sampler table utilization for module 2:
switch# show hardware flow utilization module 2Flow Utilization: 0.00% (0/515090)Total number of flows = 0IPv4 flow creation failure = 0IPv6 flow creation failure = 0MPLS flow creation failure = 0L2 flow creation failure = 0IFE flow creation failure = 0OFE flow creation failure = 0IFE CF FIFO full failure = 0OFE CF FIFO full failure = 0IFE NT table full failure = 0OFE NT table full failure = 0NO freelist pointer failure = 0Hash Table(NH) page full failure = 0IPMAC lookup failure = 0L2 ACL deny = 0L3 ACL deny = 0IFE CF flow control = 0OFE CF flow control = 0Fast Aging failure = 0switch#Related Commands
show inventory
To display inventory information for the device hardware, use the show inventory command.
show inventory [chassis | clock | fans | module | power_supply]
Syntax Description
Defaults
Displays all hardware inventory information.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display configuration incompatibilities:
switch# show inventoryNAME: "Chassis", DESCR: "Nexus7000 C7010 (10 Slot) Chassis "PID: N7K-C7010 , VID: , SN: TBM11256507NAME: "Slot 2", DESCR: "10/100/1000 Mbps Ethernet Module"PID: N7K-M148GT-11 , VID: , SN: JAB104400P0NAME: "Slot 6", DESCR: "Supervisor module-1X"PID: N7K-SUP1 , VID: TBD , SN: JAB10380101NAME: "Slot 11", DESCR: "Fabric card module"PID: N7K-C7010-FAB-1 , VID: , SN: JAB104300HMNAME: "Slot 33", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Power Supply"PID: FIORANO , VID: , SN: DTH1117T005NAME: "Slot 34", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Power Supply"PID: N7K-AC-6.0KW , VID: , SN: DTH1117T009NAME: "Slot 36", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 37", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 38", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:NAME: "Slot 39", DESCR: "Nexus7000 C7010 (10 Slot) Chassis Fan Module"PID: , VID: V00, SN:show logging console
Use the show logging console command to display the console logging configuration.
show logging console
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the console logging configuration:
switch# show logging consoleswitch#Related Commands
show logging info
Use the show logging info command to display the logging configuration.
show logging info
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging configuration:
switch# show logging infoswitch#show logging ip access-list cache
Use the show logging ip access-list cache command to display information about the logging IP access list cache.
show logging ip access-list cache
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the logging IP access list cache:
switch# show logging ip access-list cacheswitch#Related Commands
show logging last
Use the show logging last command to display the last number lines of the logfile.
show logging last number
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the last 42 lines of the logfile:
switch# show logging last 42switch#show logging level
Use the show logging level command to display the facility logging severity level configuration.
show logging level [facility]
Syntax Description
facility
(Optional) Define the appropriate logging facility. The facilities are listed in the "System Message Logging Facilities" section on page 317.
Defaults
None
Command Modes
Global configuration
Supported User RolesSuper user
VDC administrator
VDC userCommand History
4.0(1)
This command was introduced.
4.0(2)
Added interface-vlan, netstack, private-vlan, and ipv6 keywords.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the port-channel logging severity level configuration:
switch# show logging level port-channelswitch#Related Commands
show logging logfile
Use the show logging logfile command to display the messages in the log file that were timestamped within the span entered. If you do not enter an end time, the current time is used.
show logging logfile [start-time yyyy mmm dd hh:mm:ss] [end-time yyyy mmm dd hh:mm:ss]
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the messages in the log file that were timestamped within the span shown:
switch# show logging logfile start-time 2008 mar 11 12:10:00switch#Related Commands
show logging loopback
Use the show logging loopback command to display the logging loopback configuration.
show logging loopback
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Global configuration
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging loopback configuration:
switch# show logging loopbackswitch#show logging module
Use the show logging module command to display the module logging configuration.
show logging module
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the module logging configuration:
switch# show logging moduleswitch#Related Commands
show logging monitor
Use the show logging monitor command to display the monitor logging configuration.
show logging monitor
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the monitor logging configuration:
switch# show logging monitorswitch#Related Commands
show logging nvram
Use the show logging nvram command to display the messages in the NVRAM log.
show logging nvram [last number-lines]
Syntax Description
last number-lines
(Optional) Enter a number of lines to display. The last number-lines is displayed. Specify from 1 to 100 lines.
Defaults
None
Command Modes
Global configuration
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the last 20 messages in the NVRAM log:
switch# show logging nvram last 20switch#show logging onboard
To display the onboard logging information based on the error type, use the show logging onboard command.
show logging onboard {boot-uptime | device-version | counter-stats | endtime | environmental-history | error-stats | exception-log | interrupt-stats | kernel-trace | module num | obfl-history | obfl-logs | stack-trace | starttime | status}
Syntax Description
Command Default
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
The date and time arguments for the starttime and endtime keywords are entered as the date month/day/year (mm/dd/yy), followed by a hyphen, and the time in 24-hour format in hours:minutes:seconds (HH:MM:SS). For example:
•
starttime 03/17/08-15:01:57
•
The valid values for file are as follows:
•
•
•
•
•
•
•
The valid values for type are as follows:
•
–
–
–
•
•
–
–
–
–
–
–
–
–
–
•
–
–
–
•
•
–
–
–
•
•
–
–
•
•
•
–
–
–
–
–
Use this command to view OBFL data from system hardware. The OBFL feature is enabled by default and records operating temperatures, hardware uptime, interrupts, and other important events and messages that can assist with diagnosing problems with hardware cards (or modules) installed in a Cisco router or switch. Data is logged to files stored in nonvolatile memory. When the onboard hardware is started up, a first record is made for each area monitored and becomes a base value for subsequent records.
The OBFL feature provides a circular updating scheme for collecting continuous records and archiving older (historical) records, ensuring accurate data about the system. Data is recorded in one of two formats: continuous information that displays a snapshot of measurements and samples in a continuous file, and summary information that provides details about the data being collected. The message "No historical data to display" is seen when historical data is not available.
This command does not require a license.
Examples
This example shows how to display the OBFL boot and uptime information:
switch# show logging onboard module 2 boot-uptimeSat Feb 29 18:11:38 2008: Boot Record----------------------------------------------------------------Boot Time..........: Sat Feb 29 18:11:38 2008Slot Number........: 2Serial Number......: JAB0912026UBios Version.......: v0.0.8(08/18/07)Alt Bios Version...: v0.0.8(08/18/07)Firmware Version...: 3.0(1) [build 3.0(0.291)]switch#Table 7 describes the significant fields shown in the display.
This example shows how to display the OBFL logging device information:
switch# show logging onboard module 2 device-versionDevice Version Records:------------------------------------------------------------------------Timestamp Device Name Instance Hardware SoftwareNum Version Version------------------------------------------------------------------------Sat Feb 29 18:11:38 2008 Stratosphere 0 1 1Sat Feb 29 18:11:38 2008 Stratosphere 1 1 1Sat Feb 29 18:11:38 2008 Skyline-asic 0 1 1Sat Feb 29 18:11:38 2008 Tuscany-asic 0 1 0Sat Feb 29 18:11:38 2008 X-Bus IO 0 6 0Sat Feb 29 18:11:38 2008 Power Mngmnt Epl 0 6 0Sat Feb 29 18:42:01 2008 Stratosphere 0 1 1Sat Feb 29 18:42:01 2008 Stratosphere 1 1 1Sat Feb 29 18:42:01 2008 Skyline-asic 0 1 1Sat Feb 29 18:42:01 2008 Tuscany-asic 0 1 0Sat Feb 29 18:42:01 2008 X-Bus IO 0 6 0Sat Feb 29 18:42:01 2008 Power Mngmnt Epl 0 6 0switch#Table 8 describes the significant fields shown in the display.
This example shows how to display the OBFL exception log information:
switch# show logging onboard module 2 exception-logSun Feb 24 00:12:35 2008 : Exception Log RecordDevice Id : 60Device Name : DEV_SKYLINE_NIDevice Error Code : f(H)Device Error Name : SKY_NI_ERR_BM_B1_3_BIST_FAILEDSys Error : Skyline ni module experienced an errorErrtype : NON-CATASTROPHICPhyPortLayer : Fibre ChannelPort(s) Affected : 13-18Error Description : Skyline BM B1_3 BIST for interface 2 timed out during initDSAP : 0UUID : 0Time : Sun Feb 24 00:11:25 2008switch#Table 9 describes the significant fields shown in the display.
This example shows how to display the OBFL history information:
switch# show logging onboard module 2 obfl-historyOBFL history records:---------------------Sat Feb 29 30 18:09:57 2008 : OBFL all logs clearedSat Feb 29 18:47:53 2008 : OBFL miscellaneous-error logs clearedSat Feb 29 20:07:45 2008 : OBFL miscellaneous-error logs clearedswitch#The show logging onboard obfl-history command displays the following information:
•
•
•
This example shows how to display the OBFL kernel stack trace information:
switch# show logging onboard module 2 stack-trace==================== STACK TRACE ====================Logging time: Sat Feb 29 19:47:38 2008watchdog timeout: process swapper (0), jiffies 0x169bbStack: c0006e98 c001721c d195f5b4 c0005424 c0005500 c0003e90 c0005a2c c0005a40c0001a88 c01bf610 c0000394Call Trace:print_stack2_buf + 0x50kernel_thread + 0xb94klm_cctrl + 0x4554ppc_irq_dispatch_handler + 0x190do_IRQ + 0x3cret_from_intercept + 0x0probe_irq_mask + 0x494probe_irq_mask + 0x4a8transfer_to_handler + 0x15csoftnet_data + 0x2b0Registers:NIP: C0005A20 XER: 00000000 LR: C0005A2C SP: C01AA120 REGS: c01aa070 TRAP: 0500Tainted: PFMSR: 00009000 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 00DEAR: C0029B40, ESR: C01F0000MCSRR0: 00000000, MCSRR1: 00000000, MCAR: 00000000MCSR: 00000000 MCAR: 00000000 MCPSUMR: 00000000TASK = c01a8190[0] 'swapper' Last syscall: 120last math 00000000 last altivec 00000000 last spe 00000000GPR00: 00000000 C01AA120 C01A8190 00000000 00000032 C8F1DE28 D1010A9F 00000000GPR08: 0000180F C01FA39C D1010AA3 C01B8D18 24044244 1003A44C 0FFF6700 10049000GPR16: 0FFAE1B0 0FFFAC90 00000000 00000000 00000000 00000000 00000000 00000001GPR24: 00000000 00000000 00001160 007FFEAB 007FFE00 C01F0000 C01F0000 00000000·The show logging onboard stack-trace command displays the following information:
•
•
•
•
•
•
This example shows how to display the OBFL error statistics:
switch# show logging onboard module 2 error-stats----------------------------OBFL Data forModule: 2----------------------------------------------------------------------------------------------------------ERROR STATISTICS INFORMATION FOR DEVICE ID 80 DEVICE Eureka------------------------------------------------------------------------------| | Time Stamp |In|PortError Stat Counter Name | Count |MM/DD/YY HH:MM:SS|st|Rang| | |Id|e------------------------------------------------------------------------------PB2_TX FlwCtrl from conn. ASIC > pe|0x1 |02/04/08 17:07:28|00|riod Intr | | | |PB2_TX FlwCtrl from conn. ASIC > pe|0x1 |02/06/08 10:54:44|00|riod Intr | | | |------------------------------------------------------------------------------ERROR STATISTICS INFORMATION FOR DEVICE ID 81 DEVICE Lamira------------------------------------------------------------------------------| | Time Stamp |In|PortError Stat Counter Name | Count |MM/DD/YY HH:MM:SS|st|Rang| | |Id|e------------------------------------------------------------------------------NF2 Interrupt - NH HIT error |0x1 |02/06/08 10:54:44|00|switch#Table 9 describes the significant fields shown in the display.
Related Commands
clear logging onboard
Clears the OBFL entries in the persistent log.
hw-module logging onboard
Enables or disabled OBFL entries based on the error type.
show logging onboard
Use the show logging onboard command to display the onboard failure logs (OBFL).
show logging onboard {boot-uptime | device-version | endtime time [options] | environmental-history | error-stats [port number] | exception-log | interrupt-stats | module module [options] | obfl-history | obfl-logs | stack-trace | starttime time [options] | status}
Syntax Description
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to show the OBFL from March 10, 2008 at 3:45 PM:
switch# show logging onboard starttime 03/10/08-15:45:00switch#show logging server
Use the show logging server command to display the syslog server configuration.
show logging server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the syslog server configuration:
switch# show logging serverswitch#Related Commands
show logging session status
Use the show logging session status command to display the logging session status.
show logging session status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging session status:
switch# show logging session statusswitch#show logging status
Use the show logging status command to display the logging status.
show logging status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging status:
switch# show logging statusswitch#show logging timestamp
Use the show logging timestamp command to display the logging timestamp configuration.
show logging timestamp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the logging timestamp configuration:
switch# show logging timestampswitch#Related Commands
show logging level ntp
To display the Network Time Protocol syslog logging level, use the show logging level ntp command.
show logging level ntp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how display the NTP logging level:
switch(config)# show logging-level ntpRelated Commands
show module
To display module information, use the show module command.
show module [slot {bandwidth-fairness | recovery-steps} | uptime | xbar [xbar-slot]]
Syntax Description
Defaults
Displays module information for all I/O modules and supervisor modules in the chassis.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information for all modules in the chassis:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------2 48 10/100/1000 Mbps Ethernet Module N7K-M148GT-11 ok6 0 Supervisor module-1X N7K-SUP1 active *Mod Sw Hw World-Wide-Name(s) (WWN)--- -------------- ------ --------------------------------------------------2 4.0(2) 0.407 --6 4.0(2) 0.311 --Mod MAC-Address(es) Serial-Num--- -------------------------------------- ----------2 00-19-07-6c-4d-a8 to 00-19-07-6c-4d-dc JAB104400P06 00-19-07-6c-1a-78 to 00-19-07-6c-1a-80 JAB10380101* this terminal sessionThis example shows how to display information for a specific module:
switch# show module 2Mod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------2 48 10/100/1000 Mbps Ethernet Module N7K-M148GT-11 okMod Sw Hw World-Wide-Name(s) (WWN)--- -------------- ------ --------------------------------------------------2 4.0(2) 0.407 --Mod MAC-Address(es) Serial-Num--- -------------------------------------- ----------2 00-19-07-6c-4d-a8 to 00-19-07-6c-4d-dc JAB104400P0This example shows how to display information for the fabric modules:
switch# show module xbarXbar Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------1 0 Xbar N7K-C7010-FAB-1 okXbar Sw Hw World-Wide-Name(s) (WWN)--- -------------- ------ --------------------------------------------------1 NA 0.203 --Xbar MAC-Address(es) Serial-Num--- -------------------------------------- ----------1 NA JAB104300HM* this terminal sessionRelated Commands
show hardware
Displays information about the hardware.
show inventory
Displays hardware inventory information.
show ntp peer-status
To do display the status of the Network Time Protocol peers, use the show ntp peer-status command.
show ntp peer-status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the peer status for NTP:
switch(config)# show ntp peer-statusRelated Commands
show ntp peers
To display information about Network Time Protocol (NTP) peers, use the show ntp peers command.
show ntp peers
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example displays information about NTP peers:
switch(config)# show ntp peersRelated Commands
how ntp source
To display information about the Network Time Protocol source, use the show ntp source command.
show ntp source
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example displays the NTP source information:
switch(config)# show ntp sourceRelated Commands
show ntp statistics
To display Network Time Protocol (NTP) statistics, use the show ntp statistics command.
show ntp statistics {io | local | memory | peer {ipaddr address | name name1 [..namen]}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example displays statistics for NTP:
switch(config)# show ntp statistics localRelated Commands
show processes
To display the process information for a device, use the show processes command.
show processes [vdc vdc-number]
Syntax Description
Defaults
Displays information for all processes in the local device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
You can specify another VDC only from the default VDC.
This command does not require a license.
Examples
This example shows how to display the process information for a device:
switch# show processesPID State PC Start_cnt TTY Type Process----- ----- -------- ----------- ---- ---- -------------1 S b7f9e468 1 - O init2 S 0 1 - O migration/03 S 0 1 - O ksoftirqd/04 S 0 1 - O desched/05 S 0 1 - O migration/16 S 0 1 - O ksoftirqd/17 S 0 1 - O desched/18 S 0 1 - O events/09 S 0 1 - O events/110 S 0 1 - O khelper15 S 0 1 - O kthread...This example shows how to display the process information for another VDC:
switch# show processes vdc 2PID State PC Start_cnt TTY Type Process----- ----- -------- ----------- ---- ---- -------------1 S b7f9e468 1 - O init2 S 0 1 - O migration/03 S 0 1 - O ksoftirqd/04 S 0 1 - O desched/05 S 0 1 - O migration/16 S 0 1 - O ksoftirqd/17 S 0 1 - O desched/18 S 0 1 - O events/09 S 0 1 - O events/110 S 0 1 - O khelper15 S 0 1 - O kthread...show processes cpu
To display the CPU utilization information for processes on the device, use the show processes cpu command.
show processes cpu
Syntax Description
This command has no arguments or keywords.
Defaults
Displays information for all processes in the local device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the CPU utilization information for the processes:
switch# show processes cpuPID Runtime(ms) Invoked uSecs 1Sec Process----- ----------- -------- ----- ----- -----------1 286 315748 0 0 init2 302 636268 0 0 migration/03 1586 72636726 0 0 ksoftirqd/04 502 1345165 0 0 desched/05 1956 559740 3 0 migration/16 2218 457761883 0 0 ksoftirqd/17 2325 1469647 1 0 desched/18 1158 794795 1 0 events/09 1258 721210 1 0 events/110 62 2779 22 0 khelper15 0 30 25 0 kthread24 0 2 5 0 kacpid102 201 286 704 0 kblockd/0103 276 516 535 0 kblockd/1116 0 5 17 0 khubd...show processes log
To display the contents of the process log, use the show processes log command.
show processes log [details | pid process-id | vdc-all]
Syntax Description
Defaults
Displays summary information for all processes on the device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display summary information from the process log:
switch# show processes logVDC Process PID Normal-exit Stack Core Log-create-time--- --------------- ------ ----------- ----- ----- ---------------1 aclmgr 3632 N Y N Thu Mar 13 21:37:07 20081 aclmgr 4182 N Y N Wed Mar 12 13:45:38 20081 aclmgr 4205 N Y N Wed Mar 12 13:45:38 20081 adjmgr 4333 N N N Sat Nov 24 06:25:20 20071 arbiter 4332 N Y N Mon Nov 19 10:14:42 20071 arp 3870 N Y N Sat Dec 22 12:02:46 20071 clis 10005 N Y N Sat Nov 24 03:46:13 20071 clis 10268 N N N Fri Dec 14 09:13:53 20071 clis 1040 N Y N Fri Nov 16 13:34:30 2007...This example shows how to display detailed information from the process log:
switch# show processes log details======================================================Service: aclmgrDescription: ACL MgrStarted at Thu Mar 13 20:34:35 2008 (507163 us)Stopped at Thu Mar 13 20:37:07 2008 (664205 us)Uptime: 2 minutes 32 secondsStart type: SRV_OPTION_RESTART_STATELESS (23)Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)System image name: n7000-s1-dk9.4.0.1.gbinSystem image version: 4.0(1) S7PID: 3632Exit code: signal 11 (core dumped)CWD: /var/sysmgr/workVirtual Memory:CODE 08048000 - 0811CCF4DATA 0811DCF4 - 0811EBE8BRK 08121000 - 08259000STACK BFFFE270TOTAL 47244 KBRegister Set:EBX B7D64CD0 ECX 00000001 EDX 00000001ESI 41170040 EDI 00000000 EBP BFFFD1C8EAX 00000401 XDS C010007B XES 0000007BEAX FFFFFFFF (orig) EIP B7D5BEF2 XCS 00000073EFL 00010292 ESP BFFFD1C0 XSS 0000007BStack: 4272 bytes. ESP BFFFD1C0, TOP BFFFE2700xBFFFD1C0: B7D5BEE0 B7D64CD0 BFFFD1D8 B7D5C381 .....L..........0xBFFFD1D0: B7D2614C FF000226 BFFFD218 B7D232BA La..&........2..0xBFFFD1E0: B5542014 B7D25DE0 000007DE B5542014 . T..]....... T.0xBFFFD1F0: B7D08918 B7D2614C FF000226 08241A54 ....La..&...T.$.0xBFFFD200: B5542014 41170034 08241A54 B7D2614C . T.4..AT.$.La..0xBFFFD210: FF000226 BFFFD2D0 BFFFD278 B7D138CE &.......x....8..0xBFFFD220: 08246A04 08230074 BFFFD2D0 B7D5A24D .j$.t.#.....M...0xBFFFD230: B7D6369A 00002000 00000004 00000000 .6... ..........0xBFFFD240: 0000C005 00002000 BFFFD278 B7D3CF90 ..... ..x..........This example shows how to display detailed information from the process log for a specific process:
switch# show processes pid 3632======================================================Service: arpDescription: Address Resolution Protocol (ARPStarted at Sat Dec 22 12:02:19 2007 (216828 us)Stopped at Sat Dec 22 12:02:44 2007 (496964 us)Uptime: 25 secondsStart type: SRV_OPTION_RESTART_STATELESS (23)Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)System image version: 4.0(0.788) S16PID: 3912Exit code: signal 11 (core dumped)Threads: 3906 3905 4066 3917 3884 3870CWD: /var/sysmgr/workVirtual Memory:CODE 08048000 - 08071474DATA 08072474 - 08074794BRK 08075000 - 080DE000STACK BFFFEB80TOTAL 107908 KBRegister Set:EBX B7EF4264 ECX B53F45CA EDX B8009B1EESI B601C003 EDI B53F45C8 EBP B53F4578EAX B8009B1E XDS 0000007B XES 0000007BEAX FFFFFFFF (orig) EIP B7EDF9AB XCS 00000073EFL 00010286 ESP B53F4560 XSS 0000007BStack: 2688 bytes. ESP B53F4560, TOP BFFFEB800xB53F4560: B601C003 00000001 F1EC838D B7EF4264 ............dB..0xB53F4570: 00000000 00000000 B53F45D8 B7EE0C0D .........E?.....0xB53F4580: B601C003 B53F45CA B53F45C8 B53F45C0 .....E?..E?..E?.0xB53F4590: 00000001 B53F45C4 00000000 00000001 .....E?............This example shows how to display process log information for all VDCs on the physical device:
switch# show processes log vdc-allVDC Process PID Normal-exit Stack Core Log-create-time--- --------------- ------ ----------- ----- ----- ---------------1 aclmgr 3632 N Y N Thu Mar 13 21:37:07 20081 aclmgr 4182 N Y N Wed Mar 12 13:45:38 20081 aclmgr 4205 N Y N Wed Mar 12 13:45:38 20081 adjmgr 4333 N N N Sat Nov 24 06:25:20 20071 arbiter 4332 N Y N Mon Nov 19 10:14:42 20071 arp 3870 N Y N Sat Dec 22 12:02:46 20071 clis 10005 N Y N Sat Nov 24 03:46:13 20071 clis 10268 N N N Fri Dec 14 09:13:53 20071 clis 1040 N Y N Fri Nov 16 13:34:30 20071 clis 10486 N Y N Fri Nov 16 14:58:59 20071 clis 10646 N Y N Fri Nov 16 14:59:45 2007...show processes memory
To display the memory allocation information for processes, use the show processes memory command.
show processes memory [shared]
Syntax Description
Defaults
Displays memory allocated to the processes.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about memory allocation for processes:
switch# show processes memoryPID MemAlloc StackBase/Ptr Process----- -------- ----------------- ----------------1 147456 bffffda0/bffff890 init2 0 0/0 migration/03 0 0/0 ksoftirqd/04 0 0/0 desched/05 0 0/0 migration/16 0 0/0 ksoftirqd/17 0 0/0 desched/18 0 0/0 events/09 0 0/0 events/110 0 0/0 khelper15 0 0/0 kthread24 0 0/0 kacpid...This example shows how to display information about shared memory allocation for processes:
switch# show processes memory sharedComponent Shared Memory Size Used Available ReferenceAddress (kbytes) (kbytes) (kbytes) Countsmm 0X60000000 1024 3 1021 115cli 0X60110000 24576* 13991 10585 84am 0X61920000 14336* 14 14322 7urib 0X62730000 32768* 648 32120 25u6rib-ufdm 0X64740000 320* 188 132 2urib-redist 0X647A0000 4096* 0 4096 25icmpv6 0X64BB0000 2048 0 2048 2ip 0X64DC0000 8192 65 8127 23urib-ufdm 0X655D0000 2048* 0 2048 2u6rib 0X657E0000 16384* 507 15877 12ipv6 0X667F0000 8192 2 8190 9u6rib-notify 0X67000000 2048* 681 1367 12rpm 0X67210000 2048 6 2042 11mrib 0X67420000 40960 2 40958 3mrib-mfdm 0X69C30000 5120 0 5120 2m6rib 0X6A140000 10240 2 10238 3m6rib-mfdm 0X6AB50000 2048 10 2038 2igmp 0X6AD60000 8192 0 8192 2bgp 0X6B570000 8192 182 8010 1Shared memory totals - Size: 189 MB, Used: 16 MB, Available: 173 MBFree Physical Memory: 0 MB kernel, 0 MB userRelated Commands
show processes
Displays process information.
show startup-config
Displays the startup-configuration.
show redundancy status
To show detailed information about redundancy, use the show redundancy status command.
show redundancy status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example displays redundancy information:
switch# show tech-support ascii-cfgRedundancy mode---------------administrative: HAoperational: NoneThis supervisor (sup-6)-----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with no standbyOther supervisor (sup-5)------------------------Redundancy state: Not presentSupervisor state: N/AInternal state: N/ASystem start time: Fri Aug 15 15:55:19 2008System uptime: 3 days, 23 hours, 57 minutes, 22 secondsKernel uptime: 4 days, 0 hours, 1 minutes, 39 secondsActive supervisor uptime: 3 days, 23 hours, 57 minutes, 22 secondssshow rmon
To display the configuration or onboard logs, use the show rmon command.
show rmon {alarms | events | hcalarms | logs | status}
Syntax Description
Defaults
None
Command Modes
Any mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the configured RMON alarms:
switch# show rmon alarmsAlarm 20 is active, owned by testMonitors 1.3.6.1.2.1.2.2.1.16.30 every 30 second(s)Taking delta samples, last value was 17Rising threshold is 15, assigned to event 1Falling threshold is 0, assigned to event 0On startup enable rising or falling alarmThis example shows how to display the configured RMON events:
switch# show rmon eventsEvent 4 is active, owned by administrator@london_op_centerDescription is WARNING(4)Event firing causes log and trap to community public, last fired 03:32:43This example shows how to display the configured high-capacity RMON alarms:
switch# show rmon hcalarmsHigh Capacity Alarm 1 is active, owned by cseSysCPUUtilization.0@testMonitors 1.3.6.1.4.1.9.9.305.1.1.1.0 every 10 second(s)Taking absolute samples, last value was 0Rising threshold is 60, assigned to event 4Falling threshold is 59, assigned to event 4On startup enable rising alarmThis example shows how to display RMON configuration and logged information:
switch# show rmon statusMaximum allowed 32 bit or 64 bit alarms : 512Number of 32 bit alarms configured : 0Number of 64 bit hcalarms configured : 0switch#Related Commands
rmon alarm
Configures the 32-bit RMON alarm.
rmon event
Configures an RMON event.
rmon hcalarm
Configures the 64-bit RMON alarm.
show running-config eem
Use the show running-config eem command to view the Embedded Event Manager (EEM) running configuration.
show running-config eem
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the Embedded Event Manager (EEM) running configuration:
switch# show running-config eemversion 4.0(1)event manager applet oir-appletevent manager applet gold-match#show scheduler
To display information about scheduled maintenance jobs, use the show scheduler command.
show scheduler {config | internal [mem-stats] | job [name jobname] | logfile | schedule [name schedulename]}
Syntax Description
Defaults
None
Command Modes
Any
Command History
Usage Guidelines
To use this command, the scheduler must already be enabled.
To enable the scheduler, use the feature scheduler command.
Examples
The following example displays the scheduler configuration.
switch# show scheduler configconfig terminalfeature schedulerscheduler logfile size 16endconfig terminalscheduler job name test-1endconfig terminalscheduler job name testendconfig terminalscheduler job name test1endconfig terminalscheduler job name test2endswitch#The following example displays the specified scheduler timetable.
switch# show scheduler schedule name testSchedule Name : test------------------------------------User Name : adminSchedule Type : Run once on Tue Aug 10 09:48:00 2008Last Execution Time: Tue Aug 10 09:48:00 2008-----------------------------------------------Job Name Status-----------------------------------------------addMem Success (0)The following example displays internal memory statistics for the scheduler.
switch# show scheduler internal mem-statsPrivate Mem stats for UUID : Malloc track Library(103) Max types: 5--------------------------------------------------------------------------------TYPE NAME ALLOCS BYTESCURR MAX CURR MAX0 MT_MEM_other 0 0 0 01 MT_MEM_mtrack_default 0 0 0 02 MT_MEM_mtrack_hdl 4 4 2440 24403 MT_MEM_mtrack_info 108 162 1728 25924 MT_MEM_mtrack_lib_name 162 216 7233 9644--------------------------------------------------------------------------------Total bytes: 11401 (11k)--------------------------------------------------------------------------------Private Mem stats for UUID : Non mtrack users(0) Max types: 54--------------------------------------------------------------------------------TYPE NAME ALLOCS BYTESCURR MAX CURR MAX0 [r-xp]/isan/lib/convert/libsysstr.so 0 0 0 01 [r-xp]/isan/lib/convert/libvdb.so 0 0 0 02 [r-xp]/isan/plugin/0/isan/bin/scheduler 0 0 0 03 [r-xp]/isan/plugin/0/isan/lib/libaaa.so 0 0 0 04 [r-xp]/isan/plugin/0/isan/lib/libaaacon 0 0 0 05 [r-xp]/isan/plugin/0/isan/lib/libaccoun 0 1 0 466 [r-xp]/isan/plugin/0/isan/lib/libacfg.s 0 0 0 07 [r-xp]/isan/plugin/0/isan/lib/libavl.so 2 2 36 368 [r-xp]/isan/plugin/0/isan/lib/libbmp.so 0 0 0 09 [r-xp]/isan/plugin/0/isan/lib/libcmd.so 0 0 0 010 [r-xp]/isan/plugin/0/isan/lib/libcmdpat 0 0 0 011 [r-xp]/isan/plugin/0/isan/lib/libconfch 0 0 0 012 [r-xp]/isan/plugin/0/isan/lib/libdll_ob 0 0 0 013 [r-xp]/isan/plugin/0/isan/lib/libdlwrap 0 0 0 014 [r-xp]/isan/plugin/0/isan/lib/libexec.s 0 0 0 015 [r-xp]/isan/plugin/0/isan/lib/libfileut 0 0 0 016 [r-xp]/isan/plugin/0/isan/lib/libfm.so. 0 0 0 017 [r-xp]/isan/plugin/0/isan/lib/libif_ind 0 0 0 018 [r-xp]/isan/plugin/0/isan/lib/libipconf 0 0 0 019 [r-xp]/isan/plugin/0/isan/lib/libiputil 0 0 0 020 [r-xp]/isan/plugin/0/isan/lib/liblogfla 0 0 0 021 [r-xp]/isan/plugin/0/isan/lib/libmtrack 0 0 0 022 [r-xp]/isan/plugin/0/isan/lib/libmts.so 3 4 528 54023 [r-xp]/isan/plugin/0/isan/lib/libnetcfg 0 0 0 024 [r-xp]/isan/plugin/0/isan/lib/libpfm_in 0 0 0 025 [r-xp]/isan/plugin/0/isan/lib/libpss.so 74 74 50240 5024026 [r-xp]/isan/plugin/0/isan/lib/libschedc 0 0 0 027 [r-xp]/isan/plugin/0/isan/lib/libsdwrap 0 0 0 028 [r-xp]/isan/plugin/0/isan/lib/libsecuri 0 0 0 029 [r-xp]/isan/plugin/0/isan/lib/libstartu 0 0 0 030 [r-xp]/isan/plugin/0/isan/lib/libsyserr 0 0 0 031 [r-xp]/isan/plugin/0/isan/lib/libsysmgr 0 0 0 032 [r-xp]/isan/plugin/0/isan/lib/libsysmgr 0 0 0 033 [r-xp]/isan/plugin/0/isan/lib/libsysmgr 0 0 0 034 [r-xp]/isan/plugin/0/isan/lib/libtecla. 0 0 0 035 [r-xp]/isan/plugin/0/isan/lib/liburi_ma 0 0 0 036 [r-xp]/isan/plugin/0/isan/lib/liburifs. 0 0 0 037 [r-xp]/isan/plugin/0/isan/lib/liburipar 0 0 0 038 [r-xp]/isan/plugin/0/isan/lib/liburiuti 0 0 0 039 [r-xp]/isan/plugin/0/isan/lib/libutils. 2 3 42 67040 [r-xp]/isan/plugin/0/isan/lib/libvsh.so 0 0 0 041 [r-xp]/isan/plugin/0/isan/lib/libvsh_ut 0 0 0 042 [r-xp]/lib/ld-2.3.3.so 0 1 0 8343 [r-xp]/lib/libncurses.so.5.4 0 0 0 044 [r-xp]/lib/tls/libc-2.3.3.so 1 2 15 36745 [r-xp]/lib/tls/libdl-2.3.3.so 0 0 0 046 [r-xp]/lib/tls/libpthread-2.3.3.so 0 0 0 047 [r-xp]/lib/tls/librt-2.3.3.so 0 0 0 048 [r-xp]/usr/lib/libcrack.so.2 0 0 0 049 [r-xp]/usr/lib/libcrypto.so.0.9.7 0 0 0 050 [r-xp]/usr/lib/libglib-2.0.so.0.600.1 3 3 1096 109651 [r-xp]/usr/lib/libposixtime.so.1.0.0 0 0 0 052 [r-xp]/usr/lib/libz.so.1.2.1.1 0 0 0 053 [rwxp]0xbffeb000-0xbffff000 0 0 0 0--------------------------------------------------------------------------------Total bytes: 51957 (50k)--------------------------------------------------------------------------------Private Mem stats for UUID : libsdwrap(115) Max types: 22--------------------------------------------------------------------------------TYPE NAME ALLOCS BYTESCURR MAX CURR MAX0 LIBSDWRAP_SYSLOG_FLTR_CMI 0 0 0 01 LIBSDWRAP_DBG_ELEM_ARRAY 1 1 1016 10162 LIBSDWRAP_HIST_EVT_T 1 1 96 963 LIBSDWRAP_DBG_PSS_BUF 0 0 0 04 LIBSDWRAP_DBG_SHOW_BUF 0 0 0 05 LIBSDWRAP_HIST_SHOW_BUF 0 0 0 06 LIBSDWRAP_DBGDUMP_BUF 0 0 0 07 LIBSDWRAP_HIST_HDL 0 0 0 08 LIBSDWRAP_HIST_INSTHDLPTR 0 0 0 09 LIBSDWRAP_HIST_INST_HDL 0 0 0 010 LIBSDWRAP_HIST_FILESAVE_BUF 0 0 0 011 LIBSDWRAP_HIST_REC 0 0 0 012 LIBSDWRAP_HIST_LOG_TMPBUF 0 0 0 013 LIBSDWRAP_FILE_BUF 0 0 0 014 LIBSDWRAP_FILE_DBGFLAGS_BUF 0 0 0 015 LIBSDWRAP_FILE_EVLOG_BUF 0 0 0 016 LIBSDWRAP_FILE_VTYFLAGS 0 0 0 017 LIBSDWRAP_HIST_EVTBUF 0 0 0 018 LIBSDWRAP_SYS_PSSBUF 0 0 0 019 LIBSDWRAP_SYS_SHOW_BUF 0 0 0 0--------------------------------------------------------------------------------Total bytes: 1112 (1k)--------------------------------------------------------------------------------Private Mem stats for UUID : scheduler(224) Max types: 16--------------------------------------------------------------------------------TYPE NAME ALLOCS BYTESCURR MAX CURR MAX0 Log Buffer 1 1 16392 163921 Log Entry Header 0 0 0 02 Log Entry 0 0 0 03 Log Data 0 0 0 04 Job Status 0 0 0 05 Pss Configuration Key 4 4 192 1926 Pss Job Header 4 4 80 807 Pss Job Data 0 0 0 08 Pss Schedule Data 0 0 0 09 Schedule Response 0 0 0 010 Job Response 0 0 0 011 Logs Response 0 0 0 012 Script Data 0 0 0 013 Job Process Entry 0 0 0 014 Schedule Data 0 0 0 015 Sync Message 0 0 0 0--------------------------------------------------------------------------------Total bytes: 16664 (16k)--------------------------------------------------------------------------------Grand total bytes: 81134 (79k)switch#Related Commands
scheduler
Configures maintenance jobs.
feature scheduler
Enables the scheduler feature for scheduling maintenance jobs.
show snmp
To display Simple Network Management Protocol (SNMP) information, use the show snmp command.
show snmp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP information:
switch(config)# show snmpsys contact:sys location: anyplace, Anywhere0 SNMP packets input0 Bad SNMP versions0 Unknown community name0 Illegal operation for community name supplied0 Encoding errors0 Number of requested variables0 Number of altered variables0 Get-request PDUs0 Get-next PDUs0 Set-request PDUs0 SNMP packets output0 Too big errors0 No such name errors0 Bad values errors0 General errorsCommunity Group / Access--------- ---------------Comm2 network-admintestCommunity vdc-operatorcom3 vdc-admin______________________________________________________________SNMP USERS______________________________________________________________User Auth Priv(enforce) Groups____ ____ _____________ ______foo md5 aes-128(no) network-operatorvdc-adminnetwork-adminUser3 md5 no network-operatoradmin md5 des(no) network-adminuser1 md5 des(no) vdc-admin______________________________________________________________NOTIFICATION TARGET USERS (configured for sending V3 Inform)______________________________________________________________User Auth Priv____ ____ ____foo md5 no(EngineID 11:22:33:44:55)foo sha no(EngineID 33:0:33:22:33)SNMP Tcp Authentication Flag : Enabled.Related Commands
show snmp community
To display the Simple Network Management Protocol (SNMP) community strings, use the show snmp community command.
show snmp community
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
Use the show snmp community command to display a list of SNMP communities configured on a device.
In Cisco NX-OS Release 4.0(2) and later releases, the show snmp-community command displays any SNMP contexts that are mapped to SNMPv2c communities.
This command does not require a license.
Examples
This example shows how to display the SNMP community strings and any associated SNMP contexts:
switch# show snmp communityCommunity Group / Access context--------- -------------- -------testCommunity vdc-operator contextBComm2 network-admincom3 vdc-adminRelated Commands
snmp-server community
Configures SNMP community strings.
snmp-server mib community-map
Maps SNMP community strings to SNMP contexts.
show snmp context
To display the Simple Network Management Protocol (SNMP) context mapping, use the show snmp context command.
show snmp context
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP context mapping:
switch# show snmp context-------------------------------------------------------------------Context [Protocol instance, VRF, Topology]-------------------------------------------------------------------contextB instance1,vrf1,topo1-------------------------------------------------------------------rRelated Commands
show startup-config eem
Use the show startup-config eem command to view the Embedded Event Manager (EEM) start-up configuration.
show startup-config eem
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User RolesSuper user
VDC administrator
VDC userCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows the Embedded Event Manager (EEM) start-up configuration:
switch# show startup-config eemswitch#show snmp engineID
To display the Simple Network Management Protocol (SNMP) engine ID, use the show snmp engineID command.
show snmp engineID
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP engineID:
switch(config)# show snmp engineIDLocal SNMP engineID: [Hex] 80000009030005300A0B0C[Dec] 128:000:000:009:003:000:005:048:010:011:012Related Commands
show snmp group
To display the Simple Network Management Protocol (SNMP) groups, use the show snmp group command.
show snmp group
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP groups:
switch(config)# show snmp grouprole: network-admindescription: Predefined network admin role has access to all commandson the switch-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit read-writerole: network-operatordescription: Predefined network operator role has access to all readcommands on the switch-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit readrole: vdc-admindescription: Predefined vdc admin role has access to all commands withina VDC instance-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit read-writerole: vdc-operatordescription: Predefined vdc operator role has access to all read commandswithin a VDC instance-------------------------------------------------------------------Rule Perm Type Scope Entity-------------------------------------------------------------------1 permit readRelated Commands
show snmp host
To display the Simple Network Management Protocol (SNMP) host notification receivers, use the show snmp host command.
show snmp host
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP hosts:
switch(config)# show snmp host-------------------------------------------------------------------Host Port Version Level Type SecName-------------------------------------------------------------------192.0.2.1 33 v1 noauth trap Comm2-------------------------------------------------------------------192.0.2.2 162 v3 auth trap comm3Use VRF: Blue-------------------------------------------------------------------192.0.2.10 162 v3 auth trap testCommunityFilter VRF: Red-------------------------------------------------------------------Related Commands
show snmp trap
To display the Simple Network Management Protocol (SNMP) notification enable status, use the show snmp trap command.
show snmp trap
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP notification enable status:
switch(config)# show snmp trapTrap type Enabled--------- -------aaa server state-change Nocallhome Noentity fru Yeslicense Yessnmp authentication Novrrp Nolink Nobridge topologychange Nobridge newroot Nostpx inconsistency Nostpx loop-inconsistency Nostpx root-inconsistency NoRelated Commands
show snmp user
To display the Simple Network Management Protocol (SNMP) users, use the show snmp user command.
show snmp user [username [engineID id]]
Syntax Description
Defaults
Displays all users.
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP users:
switch(config)# show snmp user______________________________________________________________SNMP USERS______________________________________________________________User Auth Priv(enforce) Groups____ ____ _____________ ______foo md5 aes-128(no) network-operatorvdc-adminnetwork-adminUser3 md5 no network-operatoradmin md5 des(no) network-adminuser1 md5 des(no) vdc-admin______________________________________________________________NOTIFICATION TARGET USERS (configured for sending V3 Inform)______________________________________________________________User Auth Priv____ ____ ____foo md5 no(EngineID 11:22:33:44:55)Related Commands
show snmp sessions
To display the current Simple Network Management Protocol (SNMP) sessions, use the show snmp sessions command.
show snmp sessions
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operator
vdc-admin
vdc-operatorCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the SNMP sessions:
switch(config)# show snmp sessionsRelated Commands
show sprom
To display the contents of the serial PROM (SPROM) on the device, use the show sprom command.
show sprom {all | backplane bp-number | clock clock-number | cmp | fan fan-number | module slot | powersupply ps-number | stby-sup | sup | xbar xbar-number}
Syntax Description
Defaults
Displays summary information for all processes on the device.
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
network-operator
vdc-operatorComman