Table Of Contents

S Commands

sampler

save

scheduler

snmp-server community

snmp-server aaa-user cache-timeout

snmp-server contact

snmp-server context

snmp-server enable traps

snmp-server globalEnforcePriv

snmp-server host

snmp-server location

snmp-server mib community-map

snmp-server protocol enable

snmp-server tcp-session

snmp-server host filter_vrf

snmp-server host use_vrf

snmp-server user enforcePriv

snmp-server user

system cores

S Commands

---

This chapter describes the Cisco NX-OS system management commands that begin with the letter S, excluding the show commands.

sampler

To define a sampler and enter the sampler configuration mode, use the sampler global configuration mode command. To remove the sampler definition, use the no form of this command.

sampler name

no sampler name

Syntax Description

name	Name of the sampler.

Command Default

No samplers are defined.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

NetFlow sampling means that M out of N packets are sampled. When a packet is sampled and there is a NetFlow cache miss, a NetFlow cache entry is created for this flow. The first packet timestamp is updated and the statistics for the first packet are initialized (for example, the bytes are set to the number of bytes in the packet and packet count is set to one). If there is a NetFlow cache hit when the packet is sampled, then the cache for this flow is updated. This includes adding the number of bytes in the packet to the byte counter and incrementing the packet count by one.

Once you enter the sampler name command, you enter the sampler configuration mode, and the prompt changes to the following:

switch(config-flow-sampler)#

Within the sampler configuration mode, the following keywords and arguments are available to configure the flow monitor:

•description description—Provides a description for this sampler; maximum of 63 characters.

•exit—Exits from the current configuration mode.

•mode sample-num out-of packets—Configures the sampler mode. The valid values are as follows:

–sample-num—Number of samples per sampling. Range: 1 to 64.

–out-of—Specifies the samples per packet ratio.

–packets—Number of packets in each sampling. Range: 1 to 8192.

•no—Negates a command or sets its defaults.

This command does not require a license.

Examples

This example shows how to define a sampler and enter the sampler configuration mode:

switch(config)# sampler testsampler

switch(config-flow-sampler)#

This example shows how to configure the sampler mode:

switch(config)# sampler testsampler

switch(config-flow-sampler)# mode 24 out-of 1200

This example shows how to remove a sampler definition:

switch(config)# no sampler testsampler

switch(config-flow)#

Related Commands

Command	Description
flow exporter	Creates a flow exporter.
flow monitor	Creates a flow monitor.
flow record	Creates a flow record.

save

To save the current configuration session to a file, use the save command.

save location

Syntax Description

location

Location of the file. The location can be in bootflash:, slot0:, or volatile: The file name can be any alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to save a configuration session to a file in bootflash:

switch# configure session myACLs

switch(config-s)# save bootflash:sessions/myACLs 

Related Commands

Command	Description
delete	Deletes a file from a location.

scheduler

To schedule a maintenance job, use the scheduler command. To disable a job, use the no form of the command. Before using this command to configure a maintenance job, remote users must authenticate with the device using the scheduler aaa-authentication command.

scheduler {aaa-authentication [username username] password [0 | 7] password |
job name job-name | logfile size filesize | schedule name schedule-name}

no scheduler {aaa-authentication [username username] password [0 | 7] password |
job name job-name | logfile size filesize | schedule name schedule-name}

Syntax Description

aaa-authentication	Begins an AAA authentication exchange with a remote user.
password	Indicates the remote user is entering a password for authentication.
0	Indicates the password is in clear text.
7	Indicates the password is encrypted.
password	The remote user's password.
username username	Indicates the remote user is entering a username, and specifies the username.
logfile	Specifies a logfile configuration.
size filesize	Specifies the size of the logfile. The range is 16 to 1024 KB.
schedule	Defines a schedule for a job.
name schedule-name	Specifies the name of the schedule. The maximum length of the name is 31 characters.
job name job-name	Places you into Job Configuration mode for the specified job name. The maximum length of the name is 31 characters.
LINE	Specify the job configurations separated by semicolons.
end	Returns you to EXEC mode.
exit	Returns you to Global Configuration mode.

Defaults

None

Command Modes

Configuration mode
Job Configuration mode

Supported User Roles

Superuser
VDC administrator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

To use this command, the scheduler must already be enabled.

To enable the scheduler, use the feature scheduler command.

This command does not require a license.

---

Note The commands within a scheduler job must be entered in a single line separated by semicolons (;).

---

Examples

The following example shows how to schedule a job.

switch(config)# scheduler job name test-1

switch(config-job)# conf t;cdp timer 120;snmp community public rw

switch(config-job)# end

switch#

The following example shows how to specify the password for a remote user.

switch# config t

switch(config)# scheduler aaa-authentication password newpwd

The following example shows how to specify a clear text password for a remote user.

switch# config t

switch(config)# scheduler aaa-authentication password 0 newpwd

The following example shows how to specify an encrypted password for a remote user.

switch# config t

switch(config)# scheduler aaa-authentication password 7 newpwd2

The following example shows how to specify a name and authentication password for a remote user.

switch# config t

switch(config)# scheduler aaa-authentication username admin1 password newpwd3

Related Commands

Command	Description
feature scheduler	Enables the scheduler.
show scheduler	Displays scheduler information.

snmp-server community

To configure the Simple Network Management Protocol (SNMP) community string, use the snmp-server community command. To remove the community string, use the no form of this command.

snmp-server community name [group name | ro | rw]

no snmp-server community name [group name | ro | rw]

Syntax Description

name	SNMP community string. The name can be any alphanumeric string up to 32 characters.
group name	(Optional) Specifies the group name to which the community belongs. The name can be any alphanumeric string up to 32 characters.
ro	(Optional) Sets read-only access for this community.
rw	(Optional) Sets read-write access for this community.

Defaults

The default community access is read-only (ro).

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the snmp-server community command to configure read-only or read-write access to the SNMP agent on the device. You can optionally configure the community for an access group or user role. See the Cisco NX-OS Security Configuration Guide, Release 4.0(1) for more information on user roles.

This command does not require a license.

Examples

This example shows how to configure a read-only SNMP community:

switch# configure terminal

switch(config)# snmp-server community test ro

Related Commands

Command	Description
show snmp community	Displays information about SNMP communities.
show snmp group	Displays information about configured user roles.

snmp-server aaa-user cache-timeout

To configure the Simple Network Management Protocol (SNMP) time-out value for synchronized AAA users, use the snmp-server aaa-user cache-timeout command. To revert to default, use the no form of this command.

snmp-server aaa-user cache-timeout seconds]

no snmp-server aaa-user cache-timeout seconds]

Syntax Description

seconds

Timeout value, in seconds. The range is from 1 to 86400.

Defaults

3600 seconds.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure the AAA user synchronization timeout value:

switch# configure terminal

switch(config)# snmp-server aaa-user cache-timeout 6000

Related Commands

Command	Description
show snmp	Displays information about SNMP.

snmp-server contact

To configure the Simple Network Management Protocol (SNMP) contact information, use the snmp-server contact command. To remove the contact information, use the no form of this command.

snmp-server contact [contact-info]

no snmp-server contact [contact-info]

Syntax Description

contact-info

(Optional) SNMP contact information (sysContact). The name can be any alphanumeric string up to 255 characters.

Defaults

A zero-length string.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the snmp-server contact command to configure the SNMP sysContact variable.

This command does not require a license.

Examples

This example shows how to configure the SNMP contact:

switch# configure terminal

switch(config)# snmp-server contact Jane Smith@anyplace.com

Related Commands

Command	Description
show snmp	Displays information about SNMP.

snmp-server context

To configure the Simple Network Management Protocol (SNMP) context to logical network entity mapping, use the snmp-server context command. To remove the context, use the no form of this command.

snmp-server context context-name [instance instance-name] [vrf vrf-name] [topology topology-name]

no snmp-server context context-name [instance instance-name] [vrf vrf-name] [topology topology-name]

Syntax Description

context-name	SNMP context. The name can be any alphanumeric string up to 32 characters.
instance instance-name	(Optional) Specifies a protocol instance. The name can be any alphanumeric string up to 32 characters.
vrf vrf-name	(Optional) Specifies the virtual routing and forwarding (VRF) instance. The name can be any alphanumeric string up to 32 characters.
topology topology-name	(Optional) Specifies the topology. The name can be any alphanumeric string up to 32 characters.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(2)	This command was introduced.

Usage Guidelines

Use the snmp-server context command to map between SNMP contexts and logical network entities, such as protocol instances or VRFs.

Do not use the instance, vrf, or topology keywords to delete a context. If you use these keywords, you map the context to a zero-length string.

If you are using SNMPv2c, use the snmp-server mib community-map command to map an SNMPv2c community to an SNMP context and use the snmp-server context command to map this context to a logical network entity.

See the Cisco NX-OS Security Configuration Guide for more information on context mapping.

This command does not require a license.

Examples

This example shows how to map the public1 context to VRF red:

switch# configure terminal

switch(config)# snmp-server context public1 vrf red

Related Commands

Command	Description
show snmp context	Displays information about SNMP contexts.
snmp-server mib community-map	Maps an SNMPv2c community to an SNMP context.

snmp-server enable traps

To enable the Simple Network Management Protocol (SNMP) notifications, use the snmp-server enable traps command. To disable SNMP notifications, use the no form of this command.

snmp-server enable traps [aaa [server-state-change] | bgp | bridge [topologychange] [newroot] | callhome | eigrp | entity [fru] | license | link | ospf instance-tag [lsa | rate-limit rate] | port-security | snmp [authentication] | stp [inconsistency] [loop-consistency] [root-inconsistency]]

no snmp-server enable traps [aaa [server-state-change] | bgp | bridge [topologychange] [newroot] | callhome | eigrp | entity [fru] | license | link | ospf instance-tag [lsa | rate-limit rate] | port-security | snmp [authentication] | stp [inconsistency] [loop-consistency] [root-inconsistency]]

Syntax Description

aaa	(Optional) Enables AAA notifications.
server-state-change	(Optional) Enables the server-state-change AAA notification.
bgp	(Optional) Enable BGP notifications.
bridge	(Optional) Enable STP Bridge MIB notifications.
topologychange	(Optional) Enable STP topology change notifications.
newroot	(Optional) Enable STP new root bridge notifications.
callhome	(Optional) Enable Call Home notifications.
eigrp	(Optional) Enable EIGRP4-MIB notifications.
entity	(Optional) Enable ENTITY-MIB notifications.
fru	(Optional) Enable ENTITY-FRU-MIB notifications.
license	(Optional) Enable license notifications.
link	(Optional) Enable IF-MIB link notifications.
ospf instance-tag	(Optional) Enable Open Shortest Path First (OSPF) notifications.
lsa	(Optional) Enable OSPF LSA notifications.
rate-limit rate	(Optional) Enable rate limits on OSPF notifications. The range is from 2 to 60 seconds. The default is 10 seconds.
port-security	(Optional) Enable port security notifications.
snmp	(Optional) Enable general SNMP notifications.
authentication	(Optional) Enable SNMP authentication notifications.
stpx	(Optional) Enable STPX MIB notifications.
inconsistency	(Optional) Enables SNMP STPX MIB InconsistencyUpdate notifications.
loop-inconsistency	(Optional) Enables SNMP STPX MIB (Optional) Enables SNMP STPX MIB InconsistencyUpdate notifications.
root-inconsistency	(Optional) Enables SNMP STPX MIB RooInconsistencyUpdate notifications.

Defaults

License and SNMP authentication notifications are enabled.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(2)	Added OSPF rate-limit keyword.
4.0(3)	Added eigrp keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to enable BGP notifications:

switch# configure terminal

switch(config) snmp-server enable traps bgp

Related Commands

Command	Description
show snmp trap	Displays the enable or disable state of all SNMP notifications.

snmp-server globalEnforcePriv

To globally enforce privacy for all Simple Network Management Protocol (SNMP) users, use the snmp-server globalEnforcePriv command in configuration mode. To disable global privacy, use the no form of the command.

snmp-server globalEnforcePriv

no snmp-server globalEnforcePriv

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the snmp-server globalEnforcePriv command to enforce privacy on all SNMP users.

This command does not require a license.

Examples

This example shows how to globally enforce privacy for all SNMP contact:

switch# configure terminal

switch(config)# snmp-server contact Jane Smith@anyplace.com

Related Commands

Command	Description
show snmp	Displays information about SNMP.

snmp-server host

To configure a host receiver for Simple Network Management Protocol (SNMP) notifications, use the snmp-server host command. To remove the specified host, use the no form of the command.

snmp-server host host-address [traps | informs] [version {1 | 2c | 3 [auth | noauth | priv]}] community-string [udp-port port]

no snmp-server host host-address [traps | informs] [version {1 | 2c | 3 [auth | noauth | priv]}] community-string [udp-port port]

Syntax Description

host-address	Specifies the name or IP address of the host (the targeted recipient).
traps	Sends SNMP traps to this host.
informs	Sends SNMP informs to this host.
version	Specifies the version of the Simple Network Management Protocol (SNMP) used to send the traps. Version 3 is the most secure model, as it allows packet encryption with the priv keyword.
1	SNMPv1 (default). This option is not available with informs.
2c	SNMPv2C.
3	SNMPv3 has three optional keywords (auth, no auth (default), or priv).
auth	Enables Message Digest 5 (MD5) and Secure Hash Algorithm (SHA) packet authentication
noauth	Specifies the noAuthNoPriv security level.
priv	Enables Data Encryption Standard (DES) packet encryption (privacy).
community-string	Sends a password-like community string with the notification operation.
udp-port port	Specifies the port UDP port of the host to use. The range is from 0 to 65535. The default is 162.

Defaults

Sends SNMP traps.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example configures the recipient of an SNMP notification.

switch# config terminal

switch(config)# snmp-server host 10.1.1.1 traps version 2c abcddsfsf udp-port 500

Related Commands

Command	Description
show snmp	Displays SNMP information.
snmp-server host filter_vrf	Sends only notifications on the specified VRF to the host receiver.
snmp-server host use_vrf	Configures Cisco NX-OS to send notifications on the specified VRF to communicate with an SNMP hose receiver.

snmp-server location

To configure the device location used by the Simple Network Management Protocol (SNMP), use the snmp-server location command. To remove the location, use the no form of the command.

snmp-server location [location]

no snmp-server location [location]

Syntax Description

location

(Optional) Specifies system location. The location can be any alphanumeric string up to 255 characters.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to set the SNMP location:

switch# config terminal

switch(config)# snmp-server location SanJose

Related Commands

Command	Description
show snmp	Displays information about SNMP.

snmp-server mib community-map

To configure the Simple Network Management Protocol (SNMP) version 2c community to context mapping, use the snmp-server mib community-map command. To remove the community to context mapping, use the no form of this command.

snmp-server mib community-map community-string context context-name

no snmp-server mib community-map community-string context context-name

Syntax Description

community-string	SNMP community string. The string can be any alphanumeric string up to 32 characters.
context context-name	Specifies the SNMP context. The name can be any alphanumeric string up to 32 characters.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(2)	This command was introduced.

Usage Guidelines

Use the snmp-server mib community-map command to map between SNMPv2c communities and SNMP contexts. Use the snmp-server context command to map this context to a logical network entity.

See the Cisco NX-OS Security Configuration Guide, Release 4.0(1) for more information on context mapping.

This command does not require a license.

Examples

This example shows how to map the public community to the public1 context:

switch# configure terminal

switch(config)# snmp-server mib community-map public context public1

Related Commands

Command	Description
show snmp community	Displays information about SNMP communities.
show snmp context	Displays information about SNMP contexts.
snmp-server context	Maps an SNMP context to a logical network entity.

snmp-server protocol enable

To enable the Simple Network Management Protocol (SNMP), use the snmp-server protocol enable command. To disable the SNMP protocol, use the no form of this command.

snmp-server protocol enable

no snmp-server protocol enable

Syntax Description

This command has no arguments or keywords.

Defaults

Enabled

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

Use the no snmp protocol enable command to disable the SNMP protocol and close any TCP or UDP ports associated with the protocol.

This command does not require a license.

Examples

This example shows how disable the SNMP protocol:

switch# configure terminal

switch(config)# no snmp-server protocol enable

snmp-server tcp-session

To enable one time authentication for Simple Network Management Protocol (SNMP) over a TCP session, use the snmp-server tcp-session command. To disable one time authentication for SNMP over a TCP session, use the no form of the command.

snmp-server tcp-session [auth]

no snmp-server tcp-session [auth]

Syntax Description

auth	Enables one time authentication for SNMP over a TCP session.

Command Default

One time authentication for SNMP over a TCP session is enabled.

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example enables one time authentication for SNMP over a TCP session.

switch# config t

switch(config)# snmp-server tcp-session auth

Related Commands

Command	Description
show snmp	Displays information about SNMP.

snmp-server host filter_vrf

To configure an Simple Network Management Protocol (SNMP) host receiver to gather notifications that occur on a specific virtual routing and forwarding (VRF) instance, use the snmp-server host filter_vrf command. To remove the VRF filter, use the no form of the command.

snmp-server host host-address filter_vrf vrf-name [udp-port port]

no snmp-server host host-address filter_vrf vrf-name [udp-port port]

Syntax Description

host-address	Specifies the name or IP address of the host (the targeted recipient).
vrf-name	Name of the VRF. The name can be any alphanumeric string up to 63 characters.
udp-port port	Specifies the port UDP port of the host to use. The range is from 0 to 65535. The default is 162.

Defaults

None

Command Modes

Global configuration

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example configures the host receiver to receive notifications from the red VRF.

switch# config terminal

switch(config)# snmp-server host 10.1.1.1 filter_vrf red

Related Commands

Command	Description
show snmp	Displays SNMP information.
snmp-server host	Configures an SNMP hose receiver.
snmp-server host use_vrf	Configures Cisco NX-OS to send notifications on the specified VRF to communicate with an SNMP hose receiver.

snmp-server host use_vrf

To configure the device to communicate with an Simple Network Management Protocol (SNMP) host receiver on a specific virtual routing and forwarding (VRF) instance, use the snmp-server host use command. To return to default, use the no form of the command.

snmp-server host host-address use_vrf vrf-name [udp-port port]

no snmp-server host host-address use_vrf vrf-name [udp-port port]

Syntax Description

host-address	Specifies the name or IP address of the host (the targeted recipient).
vrf-name	Name of the VRF. The name can be any alphanumeric string up to 63 characters.
udp-port port	Specifies the port UDP port of the host to use. The range is from 0 to 65535. The default is 162.

Defaults

None

Command Modes

Global configuration

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example configures Cisco NX-OS to communicate with the host receiver on the blue VRF.

switch# config terminal

switch(config)# snmp-server host 10.1.1.1 use_vrf blue

Related Commands

Command	Description
show snmp	Displays SNMP information.
snmp-server host	Configures an SNMP hose receiver.
snmp-server host filter_vrf	Sends only notifications on the specified VRF to the host receiver.

snmp-server user enforcePriv

To enforce privacy for an Simple Network Management Protocol (SNMP) user, use the snmp-server user enforcePriv command. To revert to factory defaults, use the no form of the command.

snmp-server user username enforcePriv

no snmp-server user username enforcePriv

Syntax Description

username

Name of user. The name can be any case-sensitive alphanumeric string up to 32 characters.

Defaults

None

Command Modes

Global configuration

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example enforces privacy for the user joe.

switch# config terminal

switch(config)# snmp-server user joe enforcePriv

Related Commands

Command	Description
role name	Configures role profiles used as SNMP group names.
show snmp	Displays SNMP information.
snmp-server user	Configures SNMP user information.

snmp-server user

To configure the Simple Network Management Protocol (SNMP) user information, use the snmp-server user command. To disable the configuration or to revert to factory defaults, use the no form of the command.

snmp-server user username [group-name] [auth {md5 | sha} password [priv [aes-128] password] [localizedkey] [engineID id]

no snmp-server user username [group-name] [auth {md5 | sha} password [priv [aes-128] password] [localizedkey] [engineID id]

Syntax Description

username	Name of user. The name can be any case-sensitive alphanumeric string up to 32 characters.
group-name	(Optional) Name of group. The name can be any case-sensitive alphanumeric string up to 32 characters.
auth	(Optional) Sets authentication parameters for the user.
md5	Uses MD5 algorithm for authentication.
sha	Uses SHA algorithm for authentication.
password	User password. The password can be any case-sensitive alphanumeric string up to 64 characters. If you configure the localizedkey keyword, the password can be any case-sensitive alphanumeric string up to 130 characters
priv	(Optional) Sets encryption parameters for the user.
aes-128	(Optional) Sets 128-byte AES algorithm for privacy.
engineID id	Configures the SNMP Engine ID for a notification target user. The engineID format is a 12-digit colon-separated decimal number.
localizedkey	Sets passwords in localized key format. If you configure this keyword, the password can be any case-sensitive alphanumeric string up to 130 characters.

Defaults

None

Command Modes

Global configuration

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the snmp-server user command to configure user authentication and privacy settings for SNMP. If you use the localizedkey keyword, you cannot port the SNMP user configuration across devices as the user password contains information on the engine ID of the device. If you copy a configuration file into the device, the passwords may not be set correctly if the configuration file was generated at a different device. We recommend that you explicitly configure passwords after copying the configuration into the device.

SNMP Version 3 is the most secure model, as it allows packet encryption with the priv keyword.

To assign multiple roles to a user, configure multiple snmp-server user username group-name commands. The group-name argument is defined by the role name command.

If you are configuring an SNMP notification target user, use the engineID keyword to configure the SNMP engine ID for this user.

This command does not require a license.

Examples

This example sets the user authentication information for user jane.

switch# config terminal

switch(config)# snmp-server user jane network-admin auth sha abcd1234

This example sets multiple roles for user sam.

switch# config terminal

switch(config)# snmp-server user sam network-admin 

switch(config)# snmp-server user sam testrole 

This example sets the user authentication and privacy information for user Juan.

switch# config terminal

switch(config)# snmp-server user Juan network-admin auth sha abcd1234 priv abcdefgh

This example sets the user authentication and SNMP engine ID for a notification target user.

switch# config terminal

switch(config)# snmp-server user notifUser network-admin auth sha abcd1234 engineID 
00:12:00:00:09:03:00:05:48:00:74:30

Related Commands

Command	Description
role name	Configures role profiles used as SNMP group names.
show snmp	Displays SNMP information.
snmp-server host	Configures SNMP server host information.

system cores

To configure the destination for the system core, use the system cores command. To revert to the default, use the no form of this command.

system cores {slot0:[path] | tftp:/server//[path/]}filename

no system cores

Syntax Description

slot0:	Specifies the slot0: external file system.
path/	(Optional) Directory path to the file. The directory names in the path are case sensitive.
tftp:	Specifies a TFTP server.
/server//	Name or IPv4 address of TFTP server. The server name is case sensitive.
filename	Name for the core file. The name is alphanumeric, case sensitive, and has a maximum of 32 characters.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure a core file:

switch# configure terminal

switch(config)# system cores slot0:core_file

This example shows how to disable system core logging:

switch# configure terminal

switch(config)# no system cores

Related Commands

Command	Description
clear system cores	Clears the core file.
show system cores	Displays the core filename.