Table Of Contents

V Commands

virtual-service-blade

virtual-service-blade-type name

virtual-service-blade-type new

vlan

V Commands

---

This chapter describes the Cisco Nexus 1010 commands that begin with the letter V.

virtual-service-blade

To enter virtual service blade configuration mode and configure a virtual service, use the virtual-service-blade command. To remove a virtual service configuration, use the no form of this command.

virtual-service-blade name

no virtual-service-blade name

Syntax Description

name	User identifier that is a case-sensitive, alphanumeric character string with a maximum of 80 characters. The name cannot contain spaces or special characters.

Defaults

None

Command Modes

Global configuration (config)

Supported User Roles

network-admin

Usage Guidelines

When you use the no form of the command, you do not enter virtual service blade configuration mode.

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Examples

This example shows how to enter virtual service blade configuration mode and configure the virtual service named vsb1:

switch# configure terminal

switch(config)# virtual-service-blade vsb1 

switch(config-vsb-config)# 

This example shows how to remove the virtual service configuration named vsb1:

switch# configure terminal

switch(config)# no virtual-service-blade vsb1

switch(config)# 

Related Commands

Command	Description
virtual-service-blade-type name	Specifies the virtual service type to add to a virtual service.
virtual-service-blade-type new	Specifies the name of the software image file to add to a virtual service.
show virtual-service-blade	Displays information about virtual service blades.
show virtual-service-blade-type summary	Displays information about the virtual service types and the virtual services belonging to that type.

virtual-service-blade-type name

To specify the virtual service type to add to a virtual service, use the virtual-service-blade-type name command.

virtual-service-blade-type name type-name

Syntax Description

type-name

Name of an existing virtual service type.

Defaults

None

Command Modes

Virtual service blade configuration (config-vsb-config)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Examples

This example shows how to specify the VSM-3 virtual service type:

switch(config-vsb-config)# virtual-service-blade-type name vsm-3

switch(config-vsb-config)#

Related Commands

Command	Description
virtual-service-blade-type new	Specifies the name of the software image file to add to a virtual service.
virtual-service-blade	Places you in virtual service blade configuration mode and configures a virtual service.
show virtual-service-blade	Displays information about virtual service blades.
show virtual-service-blade-type summary	Displays information about the virtual service types and the virtual services belonging to that type.

virtual-service-blade-type new

To specify the name of the software image file to add to a virtual service, use the virtual-service-blade-type new command.

virtual-service-blade-type new iso-file-name

Syntax Description

iso-file-name

Name of the new ISO software image file in the bootflash repository folder.

Defaults

None

Command Modes

Virtual service blade configuration (config-vsb-config)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Examples

This example shows how to specify nexus-1010.4.0.4.SV1.3.51.iso as the software image file to add to the virtual service:

switch(config-vsb-config)# virtual-service-blade-type new nexus-1010.4.0.4.SV1.3.51.iso

switch(config-vsb-config)#

Related Commands

Command	Description
virtual-service-blade-type name	Specifies the virtual service type to add to a virtual service.
virtual-service-blade	Places you in virtual service blade configuration mode and configures a virtual service.
show virtual-service-blade	Displays information about virtual service blades.
show virtual-service-blade-type summary	Displays information about the virtual service types and the virtual services belonging to that type.

vlan

To create a VLAN and enter the VLAN configuration mode, use the vlan command. To remove a VLAN, use the no form of this command.

vlan {id | dot1Q tag native}

no vlan {id | dot1Q tag native}

Syntax Description

id	VLAN identification number. The range is from 1 to 4094.
dot1Q tag native	Not supported in Cisco Nexus 1010.

Defaults

The default VLAN is VLAN 1.

Command Modes

Global configuration (config)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Usage Guidelines

Specify a VLAN range by using a dash. For example, 1-9 or 20-30.

The dot1Q option is not supported in Cisco Nexus 1010.

Examples

This example shows how to create a VLAN and enter the VLAN configuration mode:

switch# configure terminal

switch(config)# vlan 10

switch(config-vlan)# 

This example shows how to remove a VLAN:

switch# configure terminal

switch(config)# no vlan 10

switch(config)# 

Related Commands

Command	Description
exit	Exits a configuration mode.
interface vlan	Applies the interface and VLAN ID to a virtual service.