Table Of Contents

I Commands

install nexus1010

interface loopback

interface mgmt

ip address

I Commands

---

This chapter describes the Cisco Nexus 1010 commands that begin with the letter I.

install nexus1010

To install management software for the Cisco Nexus 1010, use the install nexus1010 command.

install nexus1010 {bootflash: path}

Syntax Description

bootflash:	Specifies a path from the bootflash directory.
path	Full path to the image file (.iso)

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Usage Guidelines

You can view the available installation image files by using the dir command. For example:

switch# dir bootflash:

n

      77824     Mar 27 06:02:44 2010  accounting.log

      16384     Mar 26 22:31:33 2010  lost+found/

       5023     Jan 18 00:23:37 2009  mts.log

   48346519     Jan 15 21:33:25 2001  nexus-1010-mzg.4.0.4.SP1.0.171.bin

       4096     Jan 15 21:27:11 2001  repository/

Usage for bootflash://

  308473856 bytes used

 3682906112 bytes free

 3991379968 bytes total

switch# cd repository

switch# dir

      77824     Jan 24 05:02:49 2001  accounting.log

        370     Jan 24 05:03:02 2001  cppa_mgr.log

      16384     Jan 15 21:33:09 2001  lost+found/

    1331914     Jan 15 21:33:21 2001  nexus-1010.4.0.4.SP1.0.197.iso

   20971008     Jan 15 21:33:22 2001  nexus-1010-4.0.4.SP1.0.171.iso

Usage for bootflash://

  308473856 bytes used

 3682906112 bytes free

 3991379968 bytes total

Nexus1010#

Examples

This example shows how to iinstall management software for the Cisco Nexus 1010:

switch# install nexus1010 bootflash:repository/nexus-1010.4.0.4.SP1.0.197.iso

cppa_mgr debug: Using URI: bootflash:/repository/nexus-1010.4.0.4.SP1.0.197.iso

Installing bootflash:/repository/nexus-1010.4.0.4.SP1.0.197.iso

.................................................................................

Installation complete.

Save configuration and restart for changes to take effect

switch# 

#

Related Commands

Command	Description
dir	Displays the contents of a directory or file.
copy running-config startup-config	Copies the running configuration to the startup configuration.

interface loopback

To create and configure a loopback interface, use the interface loopback command. To remove a loopback interface, use the no form of this command.

interface loopback number

no interface loopback number

Syntax Description

number

Identifying interface number. The range is from 0 to 1023.

Defaults

None

Command Modes

Global configuration (config)
Interface configuration (config-if)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Usage Guidelines

Use the interface loopback command to create or modify loopback interfaces.

Examples

This example shows how to create a loopback interface:

switch(config)# interface loopback 50

switch(config-if)#

Related Commands

Command	Description
show interface brief	Displays a short version of the interface configuration.
interface mgmt	Configure the management interface and enters interface configuration mode.

interface mgmt

To configure the management interface and enter interface configuration mode, use the interface management command.

interface mgmt0

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global configuration (config)
Interface configuration (config-if)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Usage Guidelines

Use the interface mgmt0 command to configure the management interface and to enter the interface configuration mode.

Examples

This example shows how to enter the interface configuration mode to configure the management interface:

switch(config)# interface mgmt0

switch(config-if)#

Related Commands

Command	Description
show interface brief	Displays a short version of the interface configuration.
interface loopback	Create and configures a loopback interface.

ip address

To create an IP route, use the ip address command. To remove an IP address, use the no form of this command.

ip address {address mask | prefix} {next-hop | next-hop-prefix | interface-type interface-number} [tag tag-value | preference]

no ip address {address mask | prefix} {next-hop | next-hop-prefix | interface-type interface-number} [secondary | tag tag-value | preference]

Syntax Description

address	IP address, in format A.B.C.D.
mask	IP network mask, in format A.B.C.D.
prefix	IP prefix and network mask length, in format A.B.C.D/LEN.
next-hop	IP next-hop address, in format A.B.C.D.
next-hop-prefix	IP next-hop prefix in format A.B.C.D./LEN.
interface-type	Interface type.
interface-number	Interface or subinterface number.
secondary	(Optional) Configures additional IP addresses on the interface.
tag	(Optional) Specifies a supply tag.
tag-value	Supply tag value. The range of valid values is from 0 to 4294967295. The default is 0.
preference	(Optional) Route preference.

Defaults

None

Command Modes

Global configuration (config)

Supported User Roles

network-admin

Command History

Release	Modification
4.0(4)SP1(1)	This command was introduced.

Examples

This example shows how to create an IP address:

switch(config)# configure terminal

switch(config)# ip address 209.165.200.225 255.255.255.224 x

switch(config)# 

Related Commands

Command	Description
show ip interface A.B.C.D.	Displays interfaces for local IP addresses.