Table Of Contents
Device Manager System Requirements
Upgrading the Switch Module Software
Finding the Software Version and Feature Set
Upgrading a Switch Module by Using the Device Manager or Network Assistant
Upgrading a Switch Module by Using the CLI
Recovering from a Software Failure
Minimum Cisco IOS Release for Major Features
IBM BladeCenter Advanced Management Module Limitations
Update to the Device Manager Online Help
Updates to the Switch Getting Started Guide
Update to the Switch Hardware Installation Guide
Updates to the Software Configuration Guide
Correction to the "Configuring STP" Chapter
Correction to the "Configuring Network Security with ACLs" Chapter
Correction to the "Unsupported Commands" Chapter
Updates to the System Message Guide
Obtaining Documentation, Obtaining Support, and Security Guidelines
Release Notes for Cisco Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter, Cisco IOS Release 12.2(58)SE1
Revised December 22, 2011
Note
Cisco IOS Release 12.2(58)SE images for all platforms were removed from Cisco.com because of a severe defect, CSCto62631. The solution for the defect is in Cisco IOS Release 12.2(58)SE1.
Cisco IOS Release 12.2(58)SE1 runs only on Catalyst Switch Module 3110G, 3110X, and 3012.
These release notes include important information about Cisco IOS Release 12.2(58)SE and any limitations, restrictions, and caveats that apply to it. Verify that these release notes are correct for your switch module:
•
•
•
You can download the switch module software from this site (registered Cisco.com users with a login password):
http://www.cisco.com/cisco/software/navigator.html
For the complete list of Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter documentation, see the "Related Documentation" section.
Contents
•
•
•
•
•
•
•
•
System Requirements
•
Hardware Supported
Table 1 Catalyst Switch Module Supported Hardware
Cisco IOS ReleaseCatalyst Switch Module 3110G
4 external 10/100/1000BASE-T Ethernet ports, 14 internal 1000BASE-X Ethernet downlink ports, 1 internal 100BASE-T Ethernet management port, 2 StackWise Plus ports
Cisco IOS Release 12.2(40)EX2
Catalyst Switch Module 3110X
1 external 10-Gigabit Ethernet module slot, 14 internal 1000BASE-X Ethernet downlink ports, 1 internal 100BASE-T Ethernet management port, 2 StackWise Plus ports
Note
Cisco IOS Release 12.2(40)EX2
Catalyst Switch Module 3012
4 external 10/100/1000BASE-T Ethernet ports, 14 internal 1000BASE-X Ethernet downlink ports, 1 internal 100BASE-T Ethernet management port
Cisco IOS Release 12.2(40)EX2
Cisco X2 transceiver modules
X2-10GB-SR
X2-10GB-LX4
X2-10GB-CX4X2-10GB-LR
X2-10GB-LRMNote
12.2(40)EX1
12.2(46)SE
SFP modules1
GLC-T
GLC-SX-MM
GLC-LH-SMNote
12.2(52)SE
Supports OneX (CVR-X2-SFP10G) and these SFP+ modules
(For the Catalyst Switch Modules 3110G and 3110X)
SFP-10G-SR
Only version 02 or later CX12 cables are supported:
SFP-H10GB-CU1M
SFP-H10GB-CU3M
SFP-H10GB-CU5M12.2(55)SE1
1 SFP = small form-factor pluggable
2 The CX1 cables are used with the OneX converters.
Table 2 lists the IBM BladeCenter supported blade enclosures. The switch module is for use only in listed IBM BladeCenter products.
Table 2 IBM BladeCenter Supported Switch Modules
BladeCenter E (BC-E)
Yes
Yes
Yes
BladeCenter T (BC-T)
Yes
Yes
Yes
BladeCenter H (BC-H)
Yes
Yes
Yes
BladeCenter HT (BCH-T)1
Yes
Yes
Yes
BladeCenter S (BC-S)
No
No
Yes
BladeCenter Multi-switch Interconnect Module (MSIM)
Yes2
Yes2
Yes
1 The Cisco Catalyst Switch modules are not supported in the MSIM-T module.
2 The advanced Management Module (aMM) firmware must use Version 1.42i or higher.
Device Manager System Requirements
•
•
Hardware Requirements
Table 3 Minimum Hardware Requirements
Intel Pentium II1
64 MB2
256
1024 x 768
Small
1 We recommend Intel Pentium 4.
2 We recommend 256-MB DRAM.
Software Requirements
•
•
The device manager verifies the browser version when starting a session and does not require a plug-in.
CNA Compatibility
Cisco IOS Release 12.2(40)EX2 and later is only compatible with Cisco Network Assistant 5.0 and later. You can download Network Assistant from this URL:
http://www.cisco.com/go/cna_doc
For more information about Cisco Network Assistant, see the Release Notes for Cisco Network Assistant on Cisco.com.
Upgrading the Switch Module Software
These are the procedures for downloading software. Before downloading software, read this section for important information:
•
•
•
•
•
Finding the Software Version and Feature Set
The Cisco IOS image is stored as a bin file in a directory that is named with the Cisco IOS release. A subdirectory contains the files needed for web management. The image is stored on the system board flash device (flash:).
You can use the show version privileged EXEC command to see the software version that is running on your switch module. The second line of the display shows the version.
Note
You can also use the dir filesystem: privileged EXEC command to see the directory names of other software images that you might have stored in flash memory.
Deciding Which Files to Use
The upgrade procedures in these release notes describe how to perform the upgrade by using a combined tar file. This file contains the Cisco IOS image file and the files needed for the embedded device manager. You must use the combined tar file to upgrade the switch module through the device manager. To upgrade the switch module through the command-line interface (CLI), use the tar file and the archive download-sw or archive download privileged EXEC command.
The universal software images support multiple feature sets. Use the software activation feature to deploy a software license and to enable a specific feature set. For information about software activation, see the Cisco Software Activation for IBM document on Cisco.com:
http://www.cisco.com/en/US/products/ps8741/products_installation_and_configuration_guides_list.html
Archiving Software Images
Before upgrading your switch module software, make sure that you have archived copies of the current Cisco IOS release and the Cisco IOS release from which you are upgrading. You should keep these archived images until you have upgraded all network devices to the new Cisco IOS image and until you have verified that the new Cisco IOS image works properly.
Cisco routinely removes old Cisco IOS versions from Cisco.com. See Product Bulletin 2863 for more information:
You can copy the bin software image file on the flash memory to the appropriate TFTP directory on a host by using the copy flash: tftp: privileged EXEC command.
Note
You can also configure the switch module as a TFTP server to copy files from one switch module to another without using an external TFTP server by using the tftp-server global configuration command. For more information about the tftp-server command, see the "Basic File Transfer Services Commands" section of the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2, at this URL:
http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_t1.html
Upgrading a Switch Module by Using the Device Manager or Network Assistant
You can upgrade switch module software by using the device manager or Network Assistant. For detailed instructions, click Help.
Note
Upgrading a Switch Module by Using the CLI
This procedure is for copying the combined tar file to the switch module. You copy the file to the switch module from a TFTP server and extract the files. You can download an image file and replace or keep the current image.
To download software, follow these steps:
Step 1
Step 2
a.
http://www.cisco.com/cisco/software/navigator.html
b.
c.
Download the image you identified in Step 1.
Step 3
For more information, see Appendix B in the software configuration guide for this release.
Step 4
Step 5
Switch# ping tftp-server-addressFor more information about assigning an IP address and default gateway to the switch module, see the software configuration guide for this release.
Step 6
Switch# archive download-sw /overwrite /reload tftp:[[//location]/directory]/image-name.tarThe /overwrite option overwrites the software image in flash memory with the downloaded one.
The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.
For //location, specify the IP address of the TFTP server.
For /directory/image-name.tar, specify the directory (optional) and the image to download. Directory and image names are case sensitive.
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch module:
Switch# archive download-sw /overwrite tftp://198.30.20.19/cbs31x0-universal-tar.image-name.tarYou can also download the image file from the TFTP server to the switch module and keep the current image by replacing the /overwrite option with the /leave-old-sw option.
Recovering from a Software Failure
For additional recovery procedures, see the "Troubleshooting" chapter in the software configuration guide for this release.
Installation Notes
You can assign IP information to your switch module by using the IBM advanced Management Module software and the switch module device manager Express Setup program, as described in the switch module getting started guide.
New Software Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Minimum Cisco IOS Release for Major Features
Table 5 lists the minimum software release (after the first release) required to support the major features of the Catalyst Switch Module 3110G, 3110X, and 3012. Features not listed are supported in all releases.
Limitations and Restrictions
You should review this section before you begin working with the switch module. These are known limitations that will not be fixed, and there is not always a workaround. Some features might not work as documented, and some features could be affected by recent changes to the switch module hardware or software.
•
•
•
Cisco IOS Limitations
Unless otherwise noted, these limitations apply to the Catalyst Switch Module 3110G, 3110X, and 3012:
•
•
•
•
•
Access Control List
•
The workaround is to block traffic from the specific MAC address by using the mac address-table static mac-addr vlan vlan-id drop global configuration command. (CSCse73823)
Address Resolution Protocol
•
The workaround is to set the burst interval to more than 1 second. We recommend setting the burst interval to 3 seconds even if you are not experiencing this problem.(CSCse06827))
Bootloader
•
There is no workaround. It does not impact functionality. (CSCta72141)
Cisco X2 Transceiver Modules
•
The workaround is to use Cisco X2-10GB-LX4 transceiver modules with a version identification number of V03 or later. (CSCsh60076)
•
Configuration
•
PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 0, class 51, max_msg 128, total throttled 984323
-Traceback= 6625EC 5DB4C0 5DAA98 55CA80 A2F2E0 A268D8No workaround is necessary. Under normal conditions, the switch module generates this notification when snooping the next ARP packet. (CSCse47548)
•
The workaround is to not configure VLANs with protected ports as part of a fallback bridge group. (CSCsg40322)
•
The workaround is to stop the traffic in the direction in which it is not being forwarded, and then restart it after 2 seconds. You can also use the shutdown interface configuration command followed by the no shutdown command on the interface. (CSCsh04301)
•
15:50:11: %COMMON_FIB-4-FIBNULLHWIDB: Missing hwidb for fibhwidb Port-channel1 (ifindex 1632) -Traceback= A585C B881B8 B891CC 2F4F70 5550E8 564EAC 851338 84AF0C 4CEB50 859DF4 A7BF28 A98260 882658 879A58There is no workaround. (CSCsh12472)
•
The workaround is to enter the switchport access vlan dynamic interface configuration command separately on each port.(CSCsi26392)
•
show mls qos interfaceshow mls qos interface buffersshow mls qos interface policersshow mls qos interface queueingshow mls qos interface statisticsshow mac access-groupshow controllers ethernet-controllershow interfaces Gin/0/19 [all options]show idb allThere is no workaround. (CSCsk51772)
•
There is no workaround. (CSCso35380)
•
There is no workaround. (CSCso75068)
•
The workaround is to use the session stack-member-number privileged EXEC command. (CSCsz38090)
•
There is no workaround. (CSCtf34659)
HSRP
•
There is no workaround.(CSCth00938)
IEEE 802.1x Authentication
•
•
Use one of these workarounds (CSCsd90495):
–
–
•
–
–
Use one of these workarounds (CSCse04534):
–
–
Multicasting
•
–
–
–
The workaround is to not generate multicast packets with a TTL value of 0 or 1 or to disable multicast routing in the VLAN. (CSCeh21660)
•
–
–
–
There is no workaround. (CSCei08359)
•
The workaround is to not send RPF-failed multicast traffic, or make sure that the source IP address of the RPF-failed packet is reachable. (CSCsd28944)
•
There is no workaround. (CSCsd45753)
•
No workaround is necessary. The problem corrects itself when the rate or number of IGMP reports are reduced. (CSCse27757)
Quality of Service (QoS)
•
There is no workaround. (CSCeh18677)
•
There is no workaround. (CSCsc63334)
•
The workaround is to use a different name for the interface-level policy map. (CSCsd84001)
•
There is no workaround. (CSCsd72001)
•
There is no workaround. (CSCsg79627)
•
Use one of these workarounds:
–
–
•
01:01:32: %BIT-4-OUTOFRANGE: bit 1321 is not in the expected range of 0 to 1024There is no impact to switch functionality.
There is no workaround. (CSCtg32101)
RADIUS
•
There is no workaround. (CSCta05071)
Routing
•
The workaround is to not send traffic to unknown destinations. (CSCse97660)
SPAN and RSPAN
•
There is no workaround. This is a hardware limitation. (CSCei10129)
Stacking
•
There is no workaround. This is not a supported configuration. (CSCsj44478)
VLANs
•
The workaround is to remove unnecessary VLANs to reduce CPU utilization when many links are flapping. (CSCtl04815)
Device Manager Limitations
•
The workaround is to click Yes when you are prompted to accept the certificate. (CSCef45718)
IBM BladeCenter Advanced Management Module Limitations
•
See the IBM Retain database for more information.
SoL and cKVM
Serial over LAN (SoL) can be used to manage remote servers through the command-line interface (CLI) over a Telnet or Secure Shell (SSH) connection. A systems management controller is on each server, and the server serial ports are connected through an IP network. SoL is available even with no operating system on the server.
With concurrent Keyboard, Video, and Mouse (cKVM) support, an enhancement of standard KVM, you can access all servers at the same time. cKVM also uses systems management controller to send traffic.
IBM BladeCenter SoL and cKVM traffic is encapsulated and sent on one of the chassis switch modules via VLAN 4095 to the IBM management module. This traffic is sent separately from the server traffic. The IBM BladeCenter servers support VLAN 4095, SoL, and cKVM.
These limitations apply to all server facing ports on the Cisco Catalyst Switch Module CBS3110X, CBS3110G, and CBS3012:
•
There is no workaround
•
There is no workaround.
•
There is no workaround.
•
There is no workaround.
•
The workaround is to configure the proper load-balancing method that always forwards the SoL traffic to the active NIC.
•
•
On the Catalyst Switch Module 3110X only, port 14 is the collector port receiving SoL and cKVM traffic. In addition to the previous limitations, these also apply to this port:
•
•
Important Notes
Cisco IOS Notes
If the switch module requests information from the Cisco Secure Access Control Server (ACS) and the message exchange times out because the server does not respond, a message similar to this appears:
00:02:57: %RADIUS-4-RADIUS_DEAD: RADIUS server 172.20.246.206:1645,1646 is not responding.If this message appears, make sure that there is network connectivity between the switch module and the ACS. You should also make sure that the switch module has been properly configured as an AAA client on the ACS.
Device Manager Notes
•
•
•
•
From Microsoft Internet Explorer:
1.
2.
3.
4.
5.
•
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
•
If you change the HTTP port, you must include the new port number when you enter the IP address in the browser Location or Address field (for example, http://10.1.126.45:184 where 184 is the new HTTP port number). You should write down the port number through which you are connected. Use care when changing the switch module IP information.
If you are not using the default method of authentication (the enable password), you need to configure the HTTP server interface with the method of authentication used on the switch module.
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
If you use Internet Explorer Version 5.5 and select a URL with a nonstandard port at the end of the address (for example, www.cisco.com:84), you must enter http:// as the URL prefix. Otherwise, you cannot launch the device manager.
Open Caveats
•
When you make port security changes on an interface, such as configuring aging time, violations, or aging type, error messages and tracebacks might appear.
There is no workaround.
•
Unicast EIGRP packets destined for the switch are sent to the host queue instead of to the higher priority routing protocol queue.
Note
There is no workaround.
•
When a switch or switch stack running Multiple Spanning Tree (MST) is connected to a switch running Rapid Spanning Tree Protocol (RSTP), the MST switch acts as the root bridge and runs per-VLAN spanning tree (PVST) simulation mode on boundary ports connected to the RST switch. If the allowed VLAN on all trunk ports connecting these switches is changed to a VLAN other than VLAN 1 and the root port of the RSTP switch is shut down and then enabled, the boundary ports connected to the root port move immediately to the forward state without going through the PVST+ slow transition.
There is no workaround.
•
When a switch is using a DHCP server to assign IP addresses and an interface on the switch has RIP enabled, if the switch reloads, the interface loses some RIP configuration (specifically RIP authentication mode and RIP authentication key-chain). This does not happen when the IP address is statically configured on the interface. The problem occurs only when you configure RIP before an IP address is assigned by the DHCP server.
There is no workaround, but you can use an embedded event manager (EEM) script to add the interface configuration commands on the interface:
ip rip authentication mode
ip rip key-chain
•
When you configure a port to be in a dynamic VLAN by entering the switchport access vlan dynamic interface configuration command on it, the switch might reload when it processes ARP requests on the port.
The workaround is to configure static VLANs for these ports.
Resolved Caveats
•
On the Catalyst Switch Module 3012, the license boot level global configuration command shows ipbase and ipservices as available keywords. The ipservices keyword is not supported. The switch supports only the IP base image.
There is no workaround.
•
When you enter the show inventory command on a switch that has an X2 module, the output incorrectly reports the X2 module version ID (VID) as V01 even though the label has a higher VID.
There is no workaround.
•
When you reload a stack master, the ip vrf forwarding command does not appear in the running configuration, which causes AAA authentication to fail. This issue does not occur with standalone switches.
The workaround is to reenter the ip vrf forwarding command.
•
When the switch is reloaded, a static MAC entry is displayed in the running configuration, similar to the following:
mac address-table static 001e.f6ac.029d vlan 1002 interface GigabitEthernet4/0/19There is no workaround.
•
A Link Aggregation Control Protocol (LACP) bundle takes up to 70 seconds to form when NetFlow sampling is enabled.
The workaround is to disable NetFlow sampling.
•
When you configure a switch to send messages to a syslog server in a VPN Routing and Forwarding (VRF) instance, the messages are not sent to the server.
The workaround is to remove the VRF configuration.
•
When ports in an EtherChannel are linking up, the message
EC-5-CANNOT_BUNDLE2might appear. This condition is often self-correcting, indicated by the appearance ofEC-5-COMPATIBLEmessage following the first message. On occasion, the issue does not self-correct, and the ports may remain unbundled.The workaround is to reload the switch or to restore the EtherChannel bundle by shutting down and then enabling the member ports and the EtherChannel in this order:
–
–
–
–
•
A blade switch in a stack might repeatedly send faulty RPS messages, such as:
Jun 9 13:41:15: %PLATFORM_ENV-1-PWR_RPS: Redundant power supply faulty or in standby mode Jun 9 13:42:38: %PLATFORM_ENV-1-PWR_RPS: Redundant power supply faulty or in standby mode (switchB-2)There is no workaround.
•
When you connect a switch as a VLAN Trunk Protocol (VTP) client to a Catalyst 4000 switch configured as a VTP client or server and the VTP database contains more than 512 VLANs, the database is not correctly updated.
The workaround is to connect the VTP client directly to a Catalyst 6500 VTP server.
•
A host switch connected to a stack member switch can download a downloadable access control list (dACL) with more than 13 access control entries, but the dACL is not applied to an interface.
There is no workaround.
•
This message appears after inserting the CVR-X2-SFP converter module and the X2-10GB-SR transceiver modules in the10-Gigabit slots of the switch:
%GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port Te1/0/1 has bad crcThere is no workaround.
•
When a Catalyst 3750-E or 3560-E switch has a 10/100/1000BASE-TX SFP module installed in a TwinGig SFP Converter Module, and you configure the SFP module to send at 100 Mb/s, save the configuration, and reload the switch, the speed setting is not saved to the running configuration.
There is no workaround.
•
On a stack member, the show interface command output incorrectly displays a media-type setting.
There is no workaround. This is a cosmetic error and does not affect the functionality of the switch.
•
The switch does not generate SNMP traps when a power supply is disconnected.
There is no workaround.
•
Enabling the Cisco Discovery Protocol (CDP) on a tunnel interface causes the switch to fail when a a CDP packet is received on the interface.
Note
The workaround is to use the no cdp enable interface configuration command to disable CDP on the interface.
•
When a FlexLinks backup interface is configured on a member switch in a switch stack, the backup interface incorrectly shows that all VLANs are in the forwarding state.
The workaround is to use the show interface trunk interface configuration command to display the status of the backup link.
•
When a Cisco Catalyst Switch Module 3110G, 3110X, or 3012 is installed in an IBM BladeCenter H series chassis with a BladeCenter Multi-switch Interconnect Module (MSIM) in slot 7, 8, 9, or 10, the show platform chassis summary privileged EXEC command output shows the wrong switch slot ID number.
There is no workaround.
•
When you configure storm control with range command on two interfaces that belong to an EtherChannel group, this message appears:
%SYS-3-CPUHOG: Task is running for (2097)msecs, more than (2000)msecs (0/0), process = Virtual Exec.The workaround is to configure storm control on a port channel interface.
•
When MAC Authentication Bypass (MAB) is used in multi-authentication mode, a security violation occurs after successful authentication.
The workaround is to use a different authentication mode (single, multidomain or multihost).
•
The config.text.backup file is present after the switch is restored to the factory defaults.
There is no workaround.
•
When you enter the ipv6 traffic-filter interface configuration command, it might not filter traffic as expected, and it might allow traffic to pass through.
There is no workaround.
•
QoS ACL commands might appear differently in the running configuration after the master switch is reloaded or removed from the stack. The functionality of the commands remains the same.
There is no workaround.
•
When you disconnect the spanning tree protocol (STP) peer link, the STP port path cost configuration changes.
There is no workaround.
•
Two stacks that have members with fiber SFP modules are connected in a cross-stack EtherChannel with this configuration:
–
–
If a member in one stack is reloaded, this error message appears on a member switch port in the other stack and the port is error disabled.
%PLATFORM_PM-3-INTVLANINUSE: internal vlan-id 1012 allocated for interface Gi2/0/2 is still in use (3750-b-2)-Traceback= 173E7F0 198F40C 176DA04 1774E70 173FBDC 1744574 16C9C28 17C65C4 17C67D8 1BB7308 1BADD78 (3750-b-2)The workaround is to configure Layer 2 EtherChannels with SVIs and to use the EtherChannel Active mode.
•
After a switch starts and you install a Cisco Catalyst Switch Module 3110G, 3110X, or 3012 in an IBM BladeCenter H series chassis that has a BladeCenter Multi-switch Interconnect Module (MSIM) in slot 7, 8, 9, or 10, this message appears:
%Notice: Invalid Slot ID <slot>There is no workaround.
•
When a spanning-tree bridge protocol data unit (BPDU) is received on an 802.1Q trunk port and has a VLAN ID is greater than or equal to 4095, the spanning-tree lookup process fails.
There is no workaround.
•
On a switch running Protocol-Independent Multicast (PIM) and Source Specific Multicast (SSM), multicast traffic might not be sent to the correct port after the switch reloads.
The workaround is to enter the clear ip route privileged EXEC command or reconfigure PIM and SSM after a reload.
•
When a stack is running per-VLAN spanning-tree plus (PVST+) and you create a VLAN, the STP topology change resets the aging time for all members and ages out all the MAC addresses for the new VLAN. If a cookie for the new VLAN on the member is not created when the master sends the member an HRPC message to update the aging timer, the member changes the aging time for VLAN 1 to that set during the topology change.
After the topology change, the aging time for the new VLAN is reset to that before the STP topology changed. However, the aging time for VLAN 1 does not change. The MAC addresses learned on VLAN 1 and on the member switch ports age out before aging time for the new VLAN.
The workaround is to disable STP before creating a new VLAN in the stack.
•
When you enter the default interface, switchport, or no switchport interface configuration command on the switch, this message appears: EMAC phy access error, port 0, retrying......
There is no workaround.
•
On a switch running Cisco IOS Release 12.2(55)SE with the parser config cache interface global configuration command in the configuration, when you use the CISCO-MAC-NOTIFICATION-MIB to enable the SNMP MAC address notification trap, the trap is enabled, but the trap setting does not appear in the switch configuration.
The workaround is to remove the parser config cache interface command from the configuration.
•
The CPU usage on a standalone switch varies as the switch updates the running configuration.
There is no workaround.
•
When the switch stack elects a new stack master, by default the MAC address of the new master becomes the stack MAC address. Configuring a persistent MAC address sets a delay after stack master change before the stack master MAC address change. A timer value of 0 means that the MAC address of the current master is used indefinitely.
When you enter the stack-mac persistent timer 0 global configuration command on a stack and the master switch is not the original owner of the stack MAC address, ports on member switches do not go through Rapid Spanning Tree Protocol (STP) transitions directly into the forwarding state.
The workaround is to not use the stack-mac persistent timer 0 command on the switch stack.
•
When 802.1x MAC authentication bypass with multidomain authentication and critical VLAN are enabled on an interface on a switch running Cisco IOS Release 12.2(53)SE or later, if the switch loses connectivity with the AAA server, the switch might experience high CPU usage and show these messages:
AUTH-EVENT (Gi0/15) Received clear security violationAUTH-EVENT (Gi0/15) dot1x_is_mab_interested_in_mac: Still waiting for a MAC on port GigabitEthernet0/15There is no workaround.
•
Neighbor discovery fails for IPv6 hosts connected to the switch when the IPv6 MLD snooping feature is enabled globally on the switch.
The workaround is to disable IPv6 MLD snooping on the switch.
•
The port manager callback might cause more than 90% CPU usage for up to 20 minutes under these conditions:
–
–
The workaround is to disable VTP pruning.
•
The switch sends temperature trap messages when its temperature is between 58 and 60° C.
There is no workaround.
•
A switch running Cisco IOS Release 12.2(58)SE might reload if:
–
–
Use one of these workarounds:
–
–
–
Documentation Updates
Note
http://cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.
•
•
•
•
Update to the Device Manager Online Help
For Catalyst Switch Module 3110G and 3012, the physical LED behavior is different from the LED behavior on the device manager.
Updates to the Switch Getting Started Guide
When you launch Express Setup, you are prompted for the switch password. Enter the default password, cisco. The switch ignores text in the username field. Before you complete and exit Express Setup, you must change the password from the default password, cisco.
Update to the Switch Hardware Installation Guide
Catalyst Switch Module 3110X running Cisco IOS Release 12.2(52)SE or later ships with the Cisco TwinGig Converter Module (model CVR-X2-SFP) installed.
Updates to the Software Configuration Guide
Correction to the "Configuring STP" Chapter
In the "Displaying the Spanning-Tree Status" section of the "Configuring STP" chapter, this note should appear:
Note
Correction to the "Configuring Network Security with ACLs" Chapter
The "Creating a Numbered Extended ACL" section of the "Configuring Network Security with ACLs" chapter has an error. Contrary to the note in this section, ICMP echo-replies can be filtered.
Correction to the "Unsupported Commands" Chapter
The "Miscellaneous" section of the "Unsupported Commands" chapter should include the logging discriminator global configuration command.
Updates to the System Message Guide
New System Messages
Error Message IP-3-SBINIT: Error initializing [chars] subblock data structure. [chars]Explanation The subblock data structure was not initialized. [chars] is the structure identifier.
Recommended Action No action is required.
Error Message VLMAPLOG-6-ARP: vlan [dec] (port [chars]) denied arp ip [inet] -> [inet], [dec] packet[chars]Explanation A packet from the virtual LAN (VLAN) that matches the VLAN access-map (VLMAP) log criteria was detected. The first [dec] is the VLAN number, the first [chars] is the port name, the first [inet] is the source IP address, the second [inet] is the destination IP address, the second [dec] denotes the number of packets, and the second [chars] represents the letter "s" to indicate more than one packet.
Recommended Action No action is required.
Error Message VLMAPLOG-6-L4: vlan [dec] (port [chars]) denied [chars] [inet]([dec]) -> [inet]([dec]), [dec] packet[chars]Explanation A packet from the VLAN that matches the VLMAP log criteria was detected. The first [dec] is the VLAN number, the first [chars] is the port name, the second [chars] is the protocol, the first [inet] is the source IP address, the second [dec] is the source port, the second [inet] is the destination IP address, the third [dec] is the destination port, the fourth [dec] denotes the number of packets, and the third [chars] represents the letter "s" to indicate more than one packet.
Recommended Action No action is required.
Error Message VLMAPLOG-6-IGMP: vlan [dec] (port [chars]) denied igmp [inet] -> [inet] ([dec]), [dec] packet[chars]Explanation A packet from the VLAN that matches the VLMAP log criteria was detected. The first [dec] is the VLAN number, the first [chars] is the port name, the first [inet] is the source IP address, the second [inet] is the destination IP address, the second [dec] is the Internet Group Management Protocol (IGMP) message type, the third [dec] denotes the number of packets, and the second [chars] represents the letter "s" to indicate more than one packet.
Recommended Action No action is required.
Error Message VLMAPLOG-6-ICMP: vlan [dec] (port [chars]) denied icmp [inet] -> [inet] ([dec]/[dec]), [dec] packet[chars]Explanation A packet from the VLAN that matches the VLMAP log criteria was detected. The first [dec] is the VLAN number, the first [chars] is the port name, the first [inet] is the source IP address, the second [inet] is the destination IP address, the second [dec] is the Internet Control Message Protocol (ICMP) message type, the third [dec] is the ICMP message code, the fourth [dec] denotes the number of packets, and the second [chars] represents the letter "s" to indicate more than one packet.
Recommended Action No action is required.
Error Message VLMAPLOG-6-IP: vlan [dec] (port [chars]) denied ip protocol=[dec] [inet] -> [inet], [dec] packet[chars]Explanation A packet from the VLAN that matches the VLMAP log criteria was detected. The first [dec] is the VLAN number, the first [chars] is the port name, the second [dec] is the protocol number, the first [inet] is the source IP address, the second [inet] is the destination IP address, the third [dec] denotes the number of packets, and the second [chars] represents the letter "s" to indicate more than one packet.
Recommended Action No action is required.
Error Message AUTHMGR-7-STOPPING: Stopping '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars]Explanation The authentication process has been stopped. The first [chars] is the authentication method, [enet] is the Ethernet address of the host, the second [chars] is the interface for the host, and the third [chars] is the session ID.
Recommended Action No action is required.
Error Message AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client ([chars]) on Interface [chars] AuditSessionID [chars]Explanation All available authentication methods have been tried. The first [chars] is the client identifier, the second [chars]s is the interface for the client, and the third [chars] is the session ID.
Recommended Action No action is required.
Modified System Messages
Error Message AUTHMGR-5-MACMOVE: MAC address ([enet]) moved from Interface [chars] to Interface [chars]Explanation The client moved to a new interface but did not log off from the first interface. [enet] is the MAC address of the client, the first [chars] is the earlier interface, and the second [chars] is the newer interface.
Recommended Action No action is required.
Error Message AUTHMGR-5-MACREPLACE: MAC address ([enet]) on Interface [chars] is replaced by MAC ([enet])Explanation A new client has triggered a violation that caused an existing client to be replaced. The first [enet] is the first client, [chars] is the interface, the second [enet] is the new client.
Recommended Action No action is required.
Error Message EOU-6-IDENTITY_MATCH: IP=[inet]| PROFILE=EAPoUDP| POLICYNAME=[chars]| AUDITSESSID=[chars]Explanation The router has found the specifed host under the Extensible Authentication Protocol over User Datagram Protocol (EAPoUDP) identity profile. [inet] is the host IP address, the first [chars] is the enforced policy, and the second [chars] is the session ID.
Recommended Action If you do not want the host to be exempt from authentication, remove its entry from the EAPoUDP identity profile.
Error Message EOU-5-RESPONSE_FAILS: Received an EAP failure response from AAA for host=[inet]| AUDITSESSID=[chars]Explanation The router received an EAP failure response from authentication, authorization, and accounting (AAA). The host credentials were not validated. [inet] is the host, and [chars] is the session ID.
Recommended Action Check for causes of unsuccessful AAA validation of host credentials.
Error Message EOU-6-SESSION: IP=[inet]| HOST=[chars]| Interface=[chars]| AUDITSESSID=[chars]Explanation An entry for the host was created or deleted on the specified interface. [inet] is the host IP address, the first [chars] is the host identifier, the second [chars] is the interface, and the third [chars] is the session ID.
Recommended Action No action is required.
Error Message EOU-4-VERSION_MISMATCH: HOST=[inet]| Version=[dec]| AUDITSESSID=[chars]Explanation A mismatch in the EAPoUDP versions was detected from the host. [inet] is the host identifier, [dec] is the EAPoUDP version, and [chars] is the session ID.
Recommended Action Check EAPoUDP versions on peers.
Error Message EOU-6-POSTURE: IP=[inet]| HOST=[chars]| Interface=[chars]|AUDITSESSID=[chars]Explanation The posture validation status for the host. [inet] is the host IP address, the first [chars] is the host identfier, the second [chars] is the host interface, and the third [chars] is the session ID.
Recommended Action No action is required.
Error Message EOU-6-AUTHTYPE: IP=[inet]| AuthType=[chars]| AUDITSESSID=[chars]Explanation The authentication type for the host. [inet] is the host IP address, the first [chars] is the authentication type, and the second [chars] is the session ID.
Recommended Action No action is required.
Error Message EOU-4-UNKN_EVENT_ERR: UNKNOWN Event for HOST=[inet]| Event=[dec]| AUDITSESSID=[chars]Explanation Unknown message for the EAPoUDP process. [inet] is the host identifier, [dec] is the event identifier, and [chars] is the session ID.
Recommended Action File a DDTS with Cisco.
Error Message EOU-5-AAA_DOWN: AAA unreachable. METHODLIST=[chars]| HOST=[inet]| POLICY=[chars].| AUDITSESSID=[chars]Explanation The AAA servers defined by the method list cannot be reached by the host and the applied policy. The first [chars] is the method list identifer, [inet] is the host identifier, the second [chars] is the policy, and the third [chars] is the session ID.
Recommended Action Check the possible causes for unreachable AAA servers.
Error Message MAB-5-FAIL: Authentication failed for client ([chars]) on Interface [chars] AuditSessionID [chars]Explanation Authentication was unsuccessful. The first [chars] is the client, the second [chars] is the interface, and the third [chars] is the session ID.
Recommended Action No action is required.
Error Message MAB-5-SUCCESS: Authentication successful for client ([chars]) on Interface [chars] AuditSessionID [chars]Explanation Authentication was successful. The first [chars] is the client, the second [chars] is the interface, and the third [chars] is the session ID.
Recommended Action No action is required.
Deleted System Messages
Error Message IP-3-STCKYARPOVR: Attempt to overwrite Sticky ARP entry: [inet], hw: [enet] by hw: [enet]\n", MSGDEF_LIMIT_FASTExplanation Multiple stations are configured with the same IP address in a private VLAN. (This could be a case of IP address theft.) [inet] is the IP address that is configured, the first [enet] is the original MAC address associated with the IP address, and the second [enet] is the MAC address that triggered this message.
Recommended Action Change the IP address of one of the two systems.
Related Documentation
User documentation in HTML format includes the latest documentation updates and might be more current than the complete book PDF available on Cisco.com.
For more information about the switch module, see these documents on Cisco.com:
http://www.cisco.com/en/US/products/ps8741/tsd_products_support_series_home.html•
•
•
•
•
•
•
For more information about the IBM BladeCenter enclosure, see the IBM documentation:
http://www-03.ibm.com/systems/bladecenter/These compatibility matrix documents are available from this Cisco.com site:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html•
For other information about related products, see these documents:
•
•
•
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2011 Cisco Systems, Inc. All rights reserved.
