-
Cisco IOS XR System Management Command Reference for the Cisco CRS Router, Release 4.1
-
Preface
-
Boot Commands on the Cisco IOS XR Software
-
Bulk Content Downloader (BCDL) Commands on the Cisco IOS XR Software
-
Call Home Commands on the Cisco IOS XR Software
-
CDP Commands on the Cisco IOS XR Software
-
Clock Commands on the Cisco IOS XR Software
-
Configuration Management Commands on the Cisco IOS XR Software
-
Distributed Route Processor Commands on Cisco IOS XR Software
-
File System Commands on the Cisco IOS XR Software
-
Hardware Redundancy and Node Administration Commands on the Cisco IOS XR Software
-
Manageability Commands on the Cisco IOS XR Software
-
NTP Commands on the Cisco IOS XR Software
-
Process and Memory Management Commands on the Cisco IOS XR Software
-
Secure Domain Router Commands on the Cisco IOS XR Software
-
SNMP Server Commands on the Cisco IOS XR Software
-
Software Entitlement Commands on the Cisco IOS XR Software
-
Software Package Management Commands on the Cisco IOS XR Software
-
Terminal Services Commands on the Cisco IOS XR Software
-
Utility Commands on the Cisco IOS XR Software
-
Index
-
Feedback
Hardware Redundancy and Node Administration Commands on the Cisco IOS XR Software
This module describes the commands used to manage the hardware redundancy, power, and administrative status of the nodes on a router running Cisco IOS XR software.
- dsc serial
- env disable
- env power-supply disable
- fpd auto-upgrade
- hw-module boot override
- hw-module location
- hw-module power disable
- hw-module reset auto
- hw-module service maintenance-mode location
- hw-module service offline location
- hw-module subslot reload
- hw-module subslot shutdown
- redundancy switchover
- show dsc
- show environment
- show fpd package
- show hw-module fpd
- show hw-module subslot brief
- show hw-module subslot config
- show hw-module subslot counters
- show hw-module subslot errors
- show hw-module subslot plim-subblock
- show hw-module subslot registers
- show hw-module subslot status
- show inventory
- show led
- show operational
- show platform
- show redundancy
- show screddrv
- show version
- upgrade cpuctrlbits
- upgrade hw-module fpd
dsc serial
To define the serial ID for a rack, use the dsc serial command in administration configuration mode. To remove a serial ID entry from the designated shelf controller (DSC) table, use the no form of this command.
Syntax Description
serial_id Serial ID for a rack. The serial ID is included as an entry in the DSC table. Range is from 0 through 16 characters.
rack rack_num Identifies the rack whose ID you are configuring to be the serial ID .
Note For systems that include two line card chassis and one fabric chassis, the line card chassis IDs are 0 and 1, and the fabric chassis ID is F0.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The task ID was updated to system.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
For more information about identifying and selecting a DSC on your router, see Cisco IOS XR Getting Started Guide for the Cisco CRS Router.
Note
The serial ID is the hardware serial number that identifies the chassis.
Use the show running-config command to display and verify the defined serial ID for a rack.
Task ID
Examples
The following example shows how to define the serial ID for a rack:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# configure RP/0/RP0/CPU0:router(admin-config)# dsc serial TBC0610991700000 rack 1env disable
To disable environment monitoring on the chassis, use the env disable command in administration configuration mode. To reenable environment monitoring after it has been disabled, use the no form of this command.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.2
The env disable command was moved from the root-system task ID to the system task ID.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
By default, environment monitoring related to temperature and voltage is enabled on a router running Cisco IOS XR software. If environmental monitoring is disabled, you are not alerted if the router overheats.
Task ID
Examples
The following example shows how to disable environment monitoring with the env disable command:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# configure RP/0/RP0/CPU0:router(admin-config)# env disableenv power-supply disable
To disable power supply monitoring on the chassis, use the env power-supply disable command in administration configuration mode. To disable power supply monitoring, use the no form of this command.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The env power-supply command was moved from the root-system task ID to the system task ID.
The threshold {restart voltage | shutdown voltage} keywords and arguments were added to the env power-supply command.
Release 3.4.1
The threshold {restart voltage | shutdown voltage} keywords and arguments were removed, and the command was changed to env power-supply disable.
Power supply monitoring was enabled by default.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
fpd auto-upgrade
To enable the automatic upgrade of FPD images during a software upgrade, use the fpd auto-upgrade command in administration configuration mode. To disable automatic FPD upgrades, use the no form of this command.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
By default automatic upgrades of the FPD images are not performed during a software upgrade. Once the fpd auto-upgrade command is enabled, when you upgrade the software and an FPD upgrade is required, the FPD upgrade is done automatically before the router is rebooted. The automatic FPD upgrade works only if the FPD image is upgraded together with the mini installation PIE. For example, use the install add and install activate commands as shown here:
(admin)# install add comp-hfr-mini.pie hfr-fpd.pie hfr-mpls-p.pie (admin)# install activate disk0:/comp-hfr-mini.pie disk0:/hfr-fpd.piedisk0: hfr-mpls-p.pie
Task ID
Examples
Example
The following example shows how to enable automatic FPD upgrades:
RP/0/RP0/CPU0:router(admin-config)# fpd auto-upgradehw-module boot override
To place the standby RP into ROM Monitor mode so that you can update the ROMMON software in a single chassis system to a compatible ROM Monitor version, use the hw-module boot override command in administration configuration mode. To remove an RP from ROM Monitor mode, use the no form of this command.
Command History
Release
Modification
Release 3.3.0
This command was introduced.
Release 3.9.0
This command was deprecated.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note
This command is deprecated as of Cisco IOS XR Release 3.9.0.
Before you can upgrade a single-chassis system from a release of Cisco IOS XR software prior to Release 3.3.0, you need to first upgrade the ROM Monitor software to a compatible version. If you do not perform this upgrade in a single-chassis system, the standby RP fails to boot and an error message appears. To avoid boot failure, you need to use the hw-module boot override command to place the standby RP into ROM Monitor mode, and update the ROMMON software as required.
For ROM Monitor requirements, refer to the Software/Firmware Compatibility Matrix at the following URL:
http://www.cisco.com/web/Cisco_IOS_XR_Software/index.html
Use the show platform command to view a summary of the nodes in the router, including status information.
Task ID
Examples
The following example shows how to boot the standby RP to upgrade its ROMMON software to a more recent ROM Monitor version:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# configure RP/0/RP0/CPU0:router(admin-config)# hw-module boot overridehw-module location
To configure various hardware attributes for a specific node, or for all nodes installed in the router, use the hw-module location command in EXEC or administration EXEC mode.
EXEC Mode hw-module location node-id { maintenance-mode | reload path }
Administration EXEC Mode hw-module location node-id reload path
Syntax Description
node-id
Slot whose hardware attributes you want to configure. The node-id is expressed in the notation rack/slot/*.
Note Enter the show platform command to see the location of all nodes installed in the router.
maintenance-mode
Brings the node down and puts the node into maintenance mode.
reload
Resets power-cycle, reloads hardware, or both on a specific node.
path
Specific image you want to download onto the specific node or nodes. Replace path with the TFTP or disk path to the image you want to download.
Command History
Release
Modification
Release 3.3.0
This command was introduced.
Release 3.4.0
The maintenance-mode keyword was added in EXEC mode.
Release 4.1.0
The warm reload option was removed.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
To reset a specific node, or to put a node into maintenance mode, use the hw-module location command in EXEC mode.
To reset a specific node or all nodes, use the hw-module location command in administration EXEC mode.
Starting with Cisco IOS XR Release 4.0.1, it is recommended to use the partially qualified node ID in the hw-module location command. Specify an entire slot using the notation rack/slot/*.
Note
Before reloading nodes, we recommend using the cfs check command to check the sanity of the configuration file system and attempt to recover from internal inconsistencies. You need to enter the cfs check command on each secure domain router (SDR) that has nodes impacted by the reload.
Task ID
Task ID
Operations
root-lr
execute (in EXEC mode)
sysmgr
execute (in EXEC mode and administration EXEC mode)
Examples
The following example shows how to reset the hardware on a specific node from EXEC mode:
RP/0/RP0/CPU0:router # hw-module location 0/1/CPU0 reloadThe following example shows how to reset the hardware on a specific node from administration EXEC mode:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# hw-module location 0/3/CPU0 reloadhw-module power disable
To disable the node power-on feature on a specific line card, use the hw-module power disable command in administration configuration mode. To reenable the node power-on feature on a line card, use the no form of this command.
Syntax Description
location node-id Identifies the node whose power-on feature you want to disable. The node-id argument is expressed in the rack/slot/module notation.
Command History
Release
Modification
Release 3.3.0
This command was introduced.
Release 3.9.0
The option to use this command without the disable keyword was removed.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show platform command to view a summary of the nodes in the router, including status information.
The hw-module power disable command is available for line cards only; it is not available for RP cards.
Task ID
Examples
The following example shows how to disable the node power-on feature on a line card:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# configure RP/0/RP0/CPU0:router(admin-config)# hw-module power disable location 0/0/CPU0hw-module reset auto
To reset a specific node, use the hw-module reset auto command in administration configuration mode. To disable the reset feature on a specific node, use the no form of this command.
Syntax Description
disable Disables the node reset feature on the specified node.
location node-id Identifies the node you want to reload. The node-id argument is entered in the rack/slot/module notation.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The hw-module reset auto command is used to reload Cisco IOS XR software on a specific node. The node reloads with the current running configuration and active software set for that node.
Task ID
Examples
The following example shows how to reload a node:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# configure RP/0/RP0/CPU0:router(admin-config)# hw-module reset auto location 0/2/CPU0 RP/0/RP0/CPU0:router# RP/0/RP0/CPU0:Apr 2 22:04:43.659 : shelfmgr[294]: %S HELFMGR-3-USER_RESET : Node 0/2/CPU0 is reset due to user reload requesthw-module service maintenance-mode location
To configure the router to take a specific node into maintenance mode in the event of disaster recovery, use the hw-module service maintenance-mode location command in global configuration mode. To reset this configuration, use the no form of the command.
hw-module service maintenance-mode location node-id
no hw-module service maintenance-mode location node-id
Syntax Description
node-id Location of the service card that you want to move into offline mode. The node-id argument is entered in the rack/slot/module notation.
Command Default
In case of disaster recovery, the router reloads a failed line card if MDR is unsuccessful, and does not put the line card in maintenance mode.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
In the event that a line card fails, the router attempts to restart all the processes on the line card without disrupting the traffic flow. This is called a Minimum Disruptive Restart (MDR). If the MDR does not recover the line card, the router reloads the line card. You can configure the router to place the line card into maintenance mode after an unsuccessful MDR, instead of reloading it. Use the hw-module service maintenance-mode location command to configure the router to take a specified line card into maintenance mode after an unsuccessful MDR, instead of reloading the line card.
Maintenance mode is a mode in which only the processes that are required for collecting useful data for debugging run.
Task ID
Examples
The following example shows how to move the card at 0/1/CPU0 into maintenance mode:
RP/0/RP0/CPU0:router# configure RP/0/RP0/CPU0:router(config)# hw-module service maintenance-mode location 0/1/CPU0hw-module service offline location
To configure offline mode as the role for a specific node, use the hw-module service offline location command in global configuration mode. To disable offline mode, use the no form of the command.
Syntax Description
node-id Location of the service card that you want to move into offline mode. The node-id argument is entered in the rack/slot/module notation.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Offline mode disables all configured service instances on a service card. If there is a service active on the service card, the service switches over to a standby location if a standby is configured.
Task ID
hw-module subslot reload
To reload Cisco IOS XR software on a specific subslot, use the hw-module subslot reload command in EXEC mode.
Syntax Description
subslot-id Specifies the subslot to be restarted. The subslot-id argument is entered in the rack/slot/subslot notation.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command reloads Cisco IOS XR software on the specified shared port adapter (SPA) and restarts the SPA interfaces. The SPA reloads with the current running configuration and active software set for the SPA.
Task ID
hw-module subslot shutdown
To administratively shut down a specific shared port adapter (SPA), use the hw-module subslot shutdown command in global configuration mode. To return a SPA to the up state, use the no form of this command.
hw-module subslot subslot-id shutdown [ powered | unpowered ]
no hw-module subslot subslot-id shutdown
Syntax Description
subslot-id Specifies the subslot to be shut down. The subslot-id argument is entered in the rack/slot/subslot notation.
powered (Optional) Retains power to the specified subslot.
unpowered (Optional) Powers down completely the specified subslot.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command administratively shuts down the SPA in the specified subslot. Subslots that are shut down still have power but cannot load or operate Cisco IOS XR software.
Task ID
redundancy switchover
To cause the primary (active) route processor (RP) to fail over to the redundant standby RP, use the redundancy switchover command in EXEC or administration EXEC mode. To disable the forced switchover, use the no form of this command.
Syntax Description
location node-id (Optional) Specifies the primary RP on which to force a switchover. The node-id argument is expressed in the rack/slot/module notation.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The redundancy switchover command was moved from the system task ID to the root-lr task ID.
Release 3.5.0
This command was supported in administration EXEC mode.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the redundancy switchover command to trigger a switchover from the primary RP to the standby RP. When the redundancy switchover command is issued, the running (committed) configuration is automatically saved and loaded during switchover, and the standby RP becomes the active primary RP, while the original primary RP becomes the standby RP.
Note
The redundancy switchover command can be used only if the standby RP is in the ready state. Use the show redundancy command to view the status of the RPs.
Task ID
Examples
The following example shows partial output for a successful redundancy switchover operation:
RP/0/RP0/CPU0:router# show redundancy Redundancy information for node 0/RP0/CPU0: ========================================== Node 0/RP0/CPU0 is in ACTIVE role Partner node (0/RP1/CPU0) is in STANDBY role Standby node in 0/RP1/CPU0 is ready Reload and boot info ---------------------- RP reloaded Tue Mar 28 09:02:26 2006: 5 hours, 41 minutes ago Active node booted Tue Mar 28 09:02:56 2006: 5 hours, 41 minutes ago Last switch-over Tue Mar 28 09:09:26 2006: 5 hours, 34 minutes ago Standby node boot Tue Mar 28 09:10:37 2006: 5 hours, 33 minutes ago Standby node last went not ready Tue Mar 28 09:25:49 2006: 5 hours, 18 minutes go Standby node last went ready Tue Mar 28 09:25:51 2006: 5 hours, 18 minutes ago There has been 1 switch-over since reload .... RP/0/RP0/CPU0:router# redundancy switchover Initializing DDR SDRAM...found 2048 MB Initializing ECC on bank 0 ... Turning off data cache, using DDR for first time Initializing NVRAM... Testing a portion of DDR SDRAM ...done Reading ID EEPROMs ... Initializing SQUID ... Initializing PCI ... PCI0 device[1]: Vendor ID 0x10ee Configuring MPPs ... Configuring PCMCIA slots ... --More--If the standby RP is not in the ready state, the switchover operation is not allowed. The following example shows output for a failed redundancy switchover attempt:
RP/0/RP0/CPU0:router# show redundancy This node (0/RP0/CPU0) is in ACTIVE role Partner node (0/RP1/CPU0) is in UNKNOWN role RP/0/RP0/CPU0:router# redundancy switchover Standby card not running; failover disallowed.show dsc
To display the current designated shelf controller (DSC) configuration for the shelf or for the system, enter the show dsc command in administration EXEC mode.
Syntax Description
all Displays DSC information from all available nodes in the system.
mine Displays information about the current node.
location node-id Displays DSC information for a specific node. The node-id is expressed in the rack/slot/module notation.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The node keyword was replaced by the location keyword.
The show dsc command was moved from the root-system task ID to the system task ID.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
For more information about identifying and selecting a DSC on your router, see Cisco IOS XR Getting Started Guide for the Cisco CRS Router.
Task ID
Examples
The following example shows sample output from the show dsc command with the mine keyword.
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# show dsc mine Sun Jan 25 04:26:33.103 PST NODE ROLE PRIORITY TBEACON PRESENT SERIAL ID ============================================================================ 0/RP0/CPU0 DSC DEFAULT 300 YES TBA09160TBA ----------------------------------------------------------------------------The following example shows sample output from the show dsc command with the all keyword:
RP/0/RP0/CPU0:router#admin RP/0/RP0/CPU0:router(admin)#show dsc all NODE ROLE PRIORITY TBEACON PRESENT SERIAL ID ============================================================================ 0/RP0/CPU0 DSC DEFAULT 300 YES TBA09370035 ---------------------------------------------------------------------------- 0/RP1/CPU0 BACKUP DEFAULT 300 YES TBA09370035 ---------------------------------------------------------------------------- 0/4/CPU0 NON-DSC 65 300 YES TBA09370035 ---------------------------------------------------------------------------- 0/4/CPU1 NON-DSC 66 300 YES TBA09370035 ----------------------------------------------------------------------------show environment
To display environmental monitor parameters for the system, use the show environment command in EXEC mode or administration EXEC mode.
EXEC Mode: show environment [ all | last | leds | location { all | node-id } | table | temperatures | voltages ] [node-id]
Administration EXEC Mode: show environment [ all | fans | last | leds | location { all | node-id } | power-supply | table | temperatures | trace | voltages ] [node-id]
Syntax Description
all (Optional) Displays information for all environmental monitor parameters.
fans (Optional) Displays information about the fans.
last (Optional) Displays the environmental statistics at the time of the last shutdown.
leds (Optional) Displays monitor parameters for LEDs on all cards in the node.
location {all | node-id} (Optional) Displays all environmental monitor parameters for the specified location only.
power-supply (Optional) Displays power supply voltage and current information.
table (Optional) Displays environmental parameter ranges.
temperatures (Optional) Displays system temperature information.
trace (Optional) Displays trace data for environment monitoring.
voltages (Optional) Displays system voltage information.
node-id (Optional) Node whose information you want to display. The node-id argument is expressed in the rack/slot/module notation.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The optional node-id argument was supported.
The show environment command was moved from the root-system task ID to the system task ID.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show environment command displays information about the hardware that is installed in the system, including fans, LEDs, power supply voltage, and current information and temperatures.
Task ID
Examples
The following example shows sample output from the show environment command with the temperatures keyword:
RP/0/RP0/CPU0:router# show environment temperatures R/S/I Modules Inlet Exhaust Hotspot Temperature Temperature Temperature (deg C) (deg C) (deg C) 0/2/* host 31, 27 43, 45 48 cpu 31 fabricq0 46 fabricq1 44 ingressq 34 egressq 41 43 ingresspse 35 egresspse 42 plimasic 30, 31 42 0/RP1/* host 38 44 cpu 36 ingressq 42 fabricq0 43 0/SM0/* host 29, 29 41, 33The following example shows sample output from the show environment command with the temperatures keyword on the Cisco CRS Series Modular Services Card 140G:
RP/0/RP0/CPU0:router(admin)# show environment tempuratures location 0/0/cpu0 Thu Oct 28 10:45:05.852 UTC R/S/I Modules Inlet Exhaust Hotspot Temperature Temperature Temperature (deg C) (deg C) (deg C) 0/0/* host 33, 31 48, 45 47, 48, 52, 38, 57, 47, 35 cpu 52, 36 plimasic 34 46 44, 42Table 1 describes the significant fields shown in the display.
Table 2 show environment temperatures Field Descriptions Field
Description
R/S/I
Rack number, slot number, and interface for which information is displayed, in the format rack/slot/module.
Modules
Module for which temperature information is displayed.
Inlet Temperature (deg C)
Current temperature of the inlet sensor, in degrees Celsius.
Note The inlet temperature corresponds to the room air temperature entering the router.
Exhaust Temperature (deg C)
Current temperature of the exhaust sensor, in degrees Celsius.
Note The exhaust temperature corresponds to the air being exhausted from the router.
Hotspot Temperature (deg C)
Current temperature of the hotspot, in degrees Celsius.
The following example shows sample output from the show environment command the with the leds keyword:
RP/0/RP0/CPU0:router# show environment leds 0/2/*: Module (host) LED status says: OK 0/2/*: Module (plimasic) LED status says: OK 0/SM0/*: Module (host) LED status says: OKTable 2describes the significant fields shown in the display.
Table 3 show environment leds Field Descriptions Field
Description
rack_num/slot_num/*:
Rack number and slot number where the node resides.
Module (host) LED status says:
Current LED status of the specified node.
The following example shows sample output from the show environment command the with the power-supply keyword:
RP/0/RP0/CPU0:router(admin)# show env power-supply Thu Aug 5 00:18:29.492 DST Power Supply Voltage Current AC-REC AC-REC (V) (A) Zone 1: [A], [B] 54.965, 54.181 3.447, 4.073 Zone 2: [A], [B] 54.671, 54.083 8.983, 8.670 Zone 3: [A], [B] 55.063, 54.279 3.865, 4.073 Total Current: 33.111 A Total Power : 1804.049 WTable 3 describes the significant fields shown in the display.
Table 4 show environment power-supply Field Descriptions Field
Description
R/S/I
Rack number, slot number, and interface for which information is displayed, in the format PEM/Power Module/* (for example 0/PM0/*).
Modules
Module for which power information is displayed.
Capacity
Power capacity of each power module in Watts.
Status
Operational status of power modules.
Power Draw
Real (measured) power drawn from each power module.
Voltage
Real (measured) power module voltage.
Current
Real (measured) power module current draw.
Power Shelves Type
AC or DC.
Total Power Capacity
Sum of the power capacity of each of the modules installed in the chassis.
Usable Power Capacity
Sum of the power capacity of each of the powered and operational power modules installed in the chassis.
Supply Failure Protected Capacity
Protected power capacity of the chassis with power module redundancy (ASR 9010 AC 3+3, ASR 9010 DC 5+1, ASR 9006 AC 2+1, ASR 9010 DC 2+1).
Feed Failure Protected Capacity
Feed protected power capacity. This value applies to the ASR 9010 AC system only.
Worst Case Power Used
Sum of the estimated power draw of each of the load modules in the chassis. Load modules can be fan trays, RSPs and line cards.
Worst Case Power Available
Usable power capacity minus the worst case power used.
Supply Protected Capacity Available
Supply failure protected capacity minus the worst case power used.
Feed Protected Capacity Available
Feed failure protected capacity minus the worst case power used.
show fpd package
To display which shared port adapters (SPA) and SPA interface processors (SIPs) are supported with your current Cisco IOS XR software release, which field-programmable device (FPD) image you need for each SPA and SIP, and what the minimum hardware requirements are for the SPA and SIP modules, use the show fpd package command in administration EXEC mode.
Command History
Release
Modification
Release 3.4.1
The show fpd package command output was updated to display the ROMMON images.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
If there are multiple FPD images for your card, use the show fpd package command to determine which FPD image to use if you only want to upgrade a specific FPD type.
Task ID
Examples
The following example shows sample output from the show fpd package command:
RP/0/RP0/CPU0:Router# admin RP/0/RP0/CPU0:Router(admin)# show fpd package Thu Jun 24 10:58:49.319 UTC =============================== ================================================ Field Programmable Device Package ================================================ SW Min Req Min Req Card Type FPD Description Type Subtype Version SW Ver HW Vers ==================== ========================== ==== ======= =========== ======== ========= 1OC768-ITU/C OPTICS FIRMWARE 104B4 lc fpga2 104.04 0.0 0.0 ---------------------------------------------------------------------------------------------- 1OC768-DWDM-L OPTICS FIRMWARE 104B4 lc fpga2 104.04 0.0 0.0 ---------------------------------------------------------------------------------------------- 1OC768-DPSK/C OPTICS FIRMWARE 101B3 lc fpga2 101.03 0.0 0.0 ---------------------------------------------------------------------------------------------- 1OC768-DPSK/C-O OPTICS FIRMWARE 101B3 lc fpga2 101.03 0.0 0.0 ---------------------------------------------------------------------------------------------- 1OC768-DPSK/C-E OPTICS FIRMWARE 101B3 lc fpga2 101.03 0.0 0.0 ---------------------------------------------------------------------------------------------- CRS-ADVSVC-PLIM FPGA mCPU0 0.557 lc fpga2 0.557 0.0 0.0 FPGA sCPU0 0.557 lc fpga3 0.557 0.0 0.0 FPGA mCPU1 0.557 lc fpga4 0.557 0.0 0.0 FPGA sCPU1 0.557 lc fpga5 0.557 0.0 0.0 FPGA PLIM_SVC 0.41013 lc fpga1 0.41013 0.0 0.0 ---------------------------------------------------------------------------------------------- CRS1-SIP-800 JACKET FPGA swv6.0 lc fpga1 6.00 5.0 0.0 FPGA swv6.0 hwv80 lc fpga1 6.00 5.0 0.80 ---------------------------------------------------------------------------------------------- 8-10GBE FPGA swvA.0 lc fpga1 10.00 0.0 0.0 ---------------------------------------------------------------------------------------------- OC48-POS-16-ED FPGA PLIM_OC48 9.0 lc fpga1 9.00 0.0 0.0 ---------------------------------------------------------------------------------------------- 4-10GE SQUIRREL FPGA 10.0 lc fpga1 10.00 0.0 0.0 ---------------------------------------------------------------------------------------------- 42-1GE FPGA swv6.0 lc fpga1 6.00 0.0 0.0 FPGA swv6.0 hwv0.80 lc fpga1 6.00 0.0 0.80 ---------------------------------------------------------------------------------------------- 20-1GE-FLEX FPGA swv6.0 lc fpga1 6.00 0.0 0.0 FPGA swv6.0 hwv0.80 lc fpga1 6.00 0.0 0.80 ---------------------------------------------------------------------------------------------- 2-10GE-WL-FLEX FPGA swv6.0 lc fpga1 6.00 0.0 0.0 FPGA swv6.0 hwv0.80 lc fpga1 6.00 0.0 0.80 ---------------------------------------------------------------------------------------------- Route Processor ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- SC ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- RP ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Shelf Controller GE ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- RP ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Shelf Controller GE2 ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- DRP ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- DRP_B ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- S1S2S3 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- S1S3 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- S2 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Fabric HS123 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Fabric HS123 Star ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Fabric HS13 Star ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Fabric QQS123 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- LED ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- 40G-MSC ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- MSC_B ROMMONA swv1.54 asmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.52 0.0 0.0 ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- FP40 ROMMONA swv1.54 asmp lc rommonA 1.53 0.0 0.0 ROMMONA swv1.54 dsmp lc rommonA 1.53 0.0 0.0 ROMMONA swv1.54 sp lc rommonA 1.53 0.0 0.0 ROMMONB swv1.54 asmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 dsmp lc rommon 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- PSAL ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- Unknown ROMMONA swv1.54 sp lc rommonA 1.54 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- FAN ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- FC Fan Controller ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- LED ROMMONA swv1.54 sp lc rommonA 1.52 0.0 0.0 ROMMONB swv1.54 sp lc rommon 1.54 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-4XT3/E3 SPA E3 Subrate FPGA spa fpga2 1.04 0.0 0.0 SPA T3 Subrate FPGA spa fpga3 1.04 0.0 0.0 SPA I/O FPGA spa fpga1 1.00 0.0 0.0 SPA ROMMON spa rommon 2.12 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-2XT3/E3 SPA E3 Subrate FPGA spa fpga2 1.04 0.0 0.0 SPA T3 Subrate FPGA spa fpga3 1.04 0.0 0.0 SPA I/O FPGA spa fpga1 1.00 0.0 0.0 SPA ROMMON spa rommon 2.12 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-OC192POS SPA FPGA swv1.3 spa fpga1 1.03 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-8XOC12-POS SPA FPGA swv1.0 spa fpga1 1.00 0.0 0.5 ---------------------------------------------------------------------------------------------- SPA-4XOC3-POS SPA FPGA swv3.4 spa fpga1 3.04 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-OC192POS-XFP SPA FPGA swv1.2 spa fpga1 1.02 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-8X1GE SPA FPGA swv1.8 spa fpga1 1.08 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-2XOC48POS/RPR SPA FPGA swv1.0 spa fpga1 1.00 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-4XOC48POS/RPR SPA FPGA swv1.0 spa fpga1 1.00 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-10X1GE-V2 SPA FPGA swv1.10 spa fpga1 1.10 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-8X1GE-V2 SPA FPGA swv1.10 spa fpga1 1.10 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-5X1GE-V2 SPA FPGA swv1.10 spa fpga1 1.10 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-1X10GE-L-V2 SPA FPGA swv1.9 spa fpga1 1.09 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-1X10GE-WL-V2 SPA FPGA swv1.11 spa fpga1 1.11 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-1XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 1.03 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-2XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 1.03 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-3XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 1.03 0.0 0.0 ---------------------------------------------------------------------------------------------- SPA-1XOC12-ATM-V2 SPA FPGA swv1.2 spa fpga1 1.03 0.0 0.0 ----------------------------------------------------------------------------------------------
Note
In the show fpd package command output, the “subtype” column shows the FPDs that correspond with each SPA image. To upgrade a specific FPD with the upgrade hw-module fpd command, replace the fpga-type argument with the appropriate FPD from the “subtype” column, as shown in the following example:
RP/0/RP0/CPU0:router(admin)# upgrade hw-module fpd fpga2 location 0/3/1 reloadshow hw-module fpd
To display field-programmable device (FPD) compatibility for all modules or a specific module, use the show hw-module fpd command in the EXEC or administration EXE mode.
Syntax Description
location{node-id | all} Specifies the location of the module. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.
Command History
Release
Modification
Release 3.4.0
The show hw-module fpd command output was updated to display the ROMMON images.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
Examples
The following example shows how to display FPD compatibility for all modules in the router:
RP/0/RP0/CPU0:router# show hw-module fpd location all ===================================== ========================================== Existing Field Programmable Devices ========================================== HW Current SW Upg/ Location Card Type Version Type Subtype Inst Version Dng? ============ ======================== ======= ==== ======= ==== =========== ==== 0/1/CPU0 CRS1-SIP-800 0.96 lc fpga 0 2.0 No -------------------------------------------------------------------------------- 0/1/0 SPA-4XOC3-POS 1.0 spa fpga 0 3.4 No -------------------------------------------------------------------------------- 0/1/5 SPA-8X1GE 2.2 spa fpga 5 1.8 No -------------------------------------------------------------------------------- 0/6/CPU0 CRS1-SIP-800 0.96 lc fpga 0 2.0 No -------------------------------------------------------------------------------- 0/6/0 SPA-4XOC3-POS 1.0 spa fpga 0 3.4 No -------------------------------------------------------------------------------- 0/6/4 SPA-8XOC3-OC12-POS 1.1 spa fpga 4 0.5 Yes -------------------------------------------------------------------------------- 0/6/5 SPA-8X1GE 2.2 spa fpga 5 1.8 No -------------------------------------------------------------------------------- NOTES: 1. One or more FPD needs an upgrade or a downgrade. This can be accomplished using the "admin upgrade hw-module fpd" CLI.RP/0/RP0/CPU0:router# show hw-module fpd location 0/6/cpu0 Sun Apr 18 03:18:24.903 DST ===================================== ========================================== Existing Field Programmable Devices ========================================== HW Current SW Upg/ Location Card Type Version Type Subtype Inst Version Dng? ============ ======================== ======= ==== ======= ==== =========== ==== 0/6/CPU0 CRS1-SIP-800 0.96 lc fpga1 0 6.00 No lc rommonA 0 2.100 No lc rommon 0 2.100 No --------------------------------------------------------------------------------If the cards in the system do not meet the minimum requirements, the output contains a “NOTES” section that states how to upgrade the FPD image.
Related Commands
show hw-module subslot brief
To display summary information related to a specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot brief command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot brief command to obtain summary diagnostic information about a device on an interface on the SPA.
Task ID
Examples
The following example shows sample output for the show hw-module subslot brief command:
RP/0/RP0/CPU0:router# show hw-module subslot 0/1/0 brief Subslot 0/1/0 brief info: ----------------------- SPA inserted: YES SPA type: 4xOC3 POS SPA SPA operational state: READY SPA cfg admin up: YES
Table 7 show hw-module subslot config Field Descriptions Field
Description
SPA inserted
Indicates if a SPA is currently detected in the subslot.
SPA type
Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.
SPA operational state
Current state of the SPA module.
SPA cfg admin up
Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.
show hw-module subslot config
To display information related to configuration of the specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot config command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot config command to obtain diagnostic information about the configuration of an interface on the SPA.
Task ID
Examples
The following example shows sample output for the show hw-module subslot config command:
RP/0/RP0/CPU0:router# show hw-module subslot 0/6/cpu0 config Thu Feb 19 00:33:02.921 PST Subslot 0/6/0 config info: ------------------------ SPA inserted: YES SPA cfg admin up: YES SPA cfg power up: YES Subslot 0/6/1 config info: ------------------------ SPA inserted: YES SPA cfg admin up: YES SPA cfg power up: YES Subslot 0/6/2 config info: ------------------------ SPA inserted: NO SPA cfg admin up: YES SPA cfg power up: NO Subslot 0/6/3 config info: ------------------------ SPA inserted: NO SPA cfg admin up: YES SPA cfg power up: NO Subslot 0/6/4 config info: ------------------------ SPA inserted: NO SPA cfg admin up: YES SPA cfg power up: NO Subslot 0/6/5 config info: ------------------------ SPA inserted: NO SPA cfg admin up: YES SPA cfg power up: NO
Table 8 show hw-module subslot config Field Descriptions Field
Description
SPA inserted
Indicates if a SPA is currently detected in the subslot.
SPA cfg admin up
Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.
SPA cfg power up
Indicates whether the subslot is currently configured as powered or not.
show hw-module subslot counters
To display statistics related to the processing of internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot counters command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot counters command to display statistics related to the processing by the specified internal hardware device.
Task ID
Examples
The following example shows sample output for the show hw-module subslot counters command:
RP/0/RP0/CPU0:router# show hw-module subslot 0/1/cpu0 counters Subslot 0/1/0 counts info: ------------------------ SPA inserted: YES SPA type: 8xGE SPA SPA operational state: READY SPA insertion time: Wed Jan 14 11:33:24 2009 SPA last time ready: Wed Jan 14 11:33:37 2009 SPA uptime [HH:MM:SS]: 852:54:24 Subslot 0/1/1 counts info: ------------------------ SPA inserted: YES SPA type: 5xGE SPA SPA operational state: READY SPA insertion time: Wed Jan 14 11:33:24 2009 SPA last time ready: Wed Jan 14 11:33:38 2009 SPA uptime [HH:MM:SS]: 852:54:23 --More--
Table 9 show hw-module subslot counters Field Descriptions Field
Description
SPA inserted
Indicates if a SPA is currently detected in the subslot.
SPA type
Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.
SPA operational state
Current state of the SPA module.
SPA insertion time
Time the SPA module was last physically inserted or power-cycled.
SPA last time ready
Time the SPA module last changed state to up or ready (the last time the module was loaded or reloaded).
SPA uptime
The time in service or amount of time since the module was last out of service due to a reload, power cycle, or configuration event.
The following example shows sample output for the show hw-module subslot counters command with the framer keyword:
RP/0/RP0/CPU0:router# show hw-module subslot counters framer SPA device framer index 0 subindex 0 info: Milan Framer counters: STREAM 0 Rx Bytes (48-bit) (#0x381fa078-0x883c): 163857232569448 Rx Good Bytes (48-bit) (#0x381fa080-0x8840): 1964924 Rx Good Packets (48-bit) (#0x381fa040-0x8820): 26234 Tx Byte Cnt Reg (48-bit) (#0x381fe070-0xa838): 9375380 Tx Good Bytes Cnt Reg (48-bit) (#0x381fe068-0xa834): 8909442 Tx Transmitted Packet Cnt Reg (48-bit) (#0x381fe040-0xa820): 114692show hw-module subslot errors
To display error information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot errors command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot errors command to display error information related to the specified internal hardware device on a SPA.
Task ID
Examples
The following example shows partial sample output for the show hw-module subslot errors command:
RP/0/RP0/CPU0:router# show hw-module subslot 0/1/0 errors Subslot 0/1/0 errors info: ------------------------ SPA inserted: YES SPA type: 4xOC3 POS SPA SPA operational state: READY SPA last reset reason: UNKNOWN SPA last failure reason: UNKNOWN Subslot 0/1/1 errors info: ------------------------ SPA inserted: YES SPA type: 1x10GE XFP SPA SPA operational state: READY SPA last reset reason: UNKNOWN SPA last failure reason: UNKNOWN Subslot 0/1/2 errors info: ------------------------ SPA inserted: NO Subslot 0/1/3 errors info: ------------------------ SPA inserted: NO Subslot 0/1/4 errors info: ------------------------ SPA inserted: YES SPA type: 4xOC48 POS/RPR HHSPA SPA operational state: READY SPA last reset reason: UNKNOWN SPA last failure reason: UNKNOWN Subslot 0/1/5 errors info: ------------------------ SPA inserted: YES SPA type: 8xGE SPA SPA operational state: READY SPA last reset reason: UNKNOWN SPA last failure reason: UNKNOWN --More--
Table 10 show hw-module subslot errors Field Descriptions Field
Description
Subslot */*/* errors info
SPA for which error information is being displayed. The location of the SPA is expressed in the rack/slot/module notation.
SPA inserted
Indication if a SPA is currently detected in the subslot.
SPA type
Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single-height, FHSPA—double-height), and optics type.
SPA operational state
Current operational state of the SPA module.
SPA last reset reason
Reason for the most recent reset of this SPA.
SPA last failure reason
Reason for the last failure on this SPA.
show hw-module subslot plim-subblock
To display SPA firmware information for a shared port adapter (SPA), use the show hw-module subslot plim-subblock command in EXEC mode.
Syntax Description
node-id (Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show hw-module subslot plim-subblock command to display SPA firmware information, both kernel and application information, as well as heartbeat and keepalive information. The show hw-module subslot plim-subblock command is mainly used for debugging purposes.
Task ID
Examples
The following example shows sample output for the show hw-module subslot plim-subblock command:
RP/0/0/CPU0:router# show hw-module subslot 0/5/0 plim-subblock Subslot 0/5/0 Plim Subblock Info: ------------------------------------- Firmware information: SPA v4.10.1, ifs-spa_ppc_iox.elf Application v3.44.0, spa_ct3_pat_apps_iox.tar.gz SPA keepalive information: Heartbeat check disabled : FALSE Keepalive seq 372638, seen 372637, Time since last ipc keep 1sshow hw-module subslot registers
To display register information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot registers command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the command to display the nodes on the router.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot registers command to display register information for the specified internal hardware device on the SPA.
Task ID
Examples
The following example shows sample output for the show hw-module subslot registers command:
RP/0/RP0/CPU0:router# show hw-module subslot 0/1/cpu0 registers Thu Feb 19 00:38:32.908 PST Subslot 0/1/0 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000A Subslot 0/1/1 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000A Subslot 0/1/2 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000A Subslot 0/1/3 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000A Subslot 0/1/4 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000A Subslot 0/1/5 registers info: --------------------------- SPA hardware ID : 0x0 SPA SW FPGA rev.: 0x1000Ashow hw-module subslot status
To display status information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot status command in EXEC mode.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.
Use the show hw-module subslot status command to obtain status information about an interface on the SPA.
Task ID
Examples
The following example shows sample output for the show hw-module subslot status command with the temperature-sensor option:
RP/0/RP0/CPU0:router# show hw-module subslot 0/2/CPU0 status temperature-sensor SPA device temperature-sensor index 0 subindex 0 info: DS1631 (0x0803c2e4) device status: temperature = 0x1c80 (28.5 degree C) SPA device temperature-sensor index 0 subindex 0 info: DS1631 (0x08063bec) device status: temperature = 0x1e00 (30.0 degree C)show inventory
To retrieve and display information about all the Cisco products that are installed in the router, use the show inventory command in EXEC or administration EXEC mode.
EXEC Modeshow inventory [ node-id | all | location { node-id | all } | raw ]
Administration EXEC Modeshow inventory [ node-id | all | chassis | fans | location { node-id | all } | power-supply | raw ]
Syntax Description
node-id (Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.
all (Optional) Displays inventory information for all the physical entities in the chassis.
location {node-id | all} (Optional) Displays inventory information for a specific node, or for all nodes in the chassis.
raw (Optional) Displays raw information about the chassis for diagnostic purposes.
chassis (Optional) Displays inventory information for the entire chassis.
fans (Optional) Displays inventory information for the fans.
power-supply (Optional) Displays inventory information for the power supply.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
If a Cisco entity is not assigned a product ID (PID), that entity is not retrieved or displayed.
Enter the show inventory command with the raw keyword to display every RFC 2737 entity installed in the router, including those without a PID, unique device identifier (UDI), or other physical identification.
Note
The raw keyword is primarily intended for troubleshooting problems with the show inventory command itself.
If any of the Cisco products do not have an assigned PID, the output displays incorrect PIDs, and version ID (VID) and serial number (SN) elements may be missing.
For UDI compliance products, the PID, VID, and SN are stored in EEPROM and NVRAM. Use the show inventory command to display this information.
Task ID
Examples
The following example shows partial sample output from the show inventory command with the raw keyword:
RP/0/RP0/CPU0:router# show inventory raw Sun Jan 25 07:40:57.903 PST NAME: "0/1/*", DESCR: "Cisco CRS-1 Series Modular Services Card" PID: CRS-MSC , VID: V02, SN: SAD09280BS9 NAME: "0/1/* - cpu", DESCR: "cpu" PID: , VID: V00, SN: SAD093000JR NAME: "0/1/* - cpu - 1.6V_P0", DESCR: "Voltage Sensor" PID: , VID: N/A, SN: NAME: "0/1/* - cpu - 1.8V_A", DESCR: "Voltage Sensor" PID: , VID: N/A, SN: NAME: "0/1/* - cpu - 2.5V_A", DESCR: "Voltage Sensor" PID: , VID: N/A, SN: NAME: "0/1/* - cpu - 3.3V_A", DESCR: "Voltage Sensor" PID: , VID: N/A, SN: NAME: "0/1/* - cpu - 5V_A", DESCR: "Voltage Sensor" PID: , VID: N/A, SN: NAME: "0/1/* - cpu - Hotspot0", DESCR: "Temperature Sensor" PID: , VID: N/A, SN: --More--The following example shows partial sample output from the show inventory command:
RP/0/RP0/CPU0:router# show inventory Tue Apr 27 02:57:55.671 DST NAME: "0/6/*", DESCR: "Cisco CRS-1 Series Modular Services Card" PID: CRS-MSC , VID: V03, SN: SAD093702ES NAME: "0/PL6/*", DESCR: "Cisco Carrier Routing System SPA Interface Processor Card" PID: CRS1-SIP-800 , VID: V01, SN: SAD094203W2 NAME: "0/6/CPU0/129", DESCR: "CPU_PORT_1" PID: , VID: N/A, SN: NAME: "0/6/0", DESCR: "4-port OC3/STM1 POS Shared Port Adapter" PID: SPA-4XOC3-POS , VID: V01, SN: JAB093309MG NAME: "0/6/1", DESCR: "Cisco 1-Port 10GE LAN/WAN-PHY Shared Port Adapter" PID: SPA-1X10GE-WL-V2 , VID: V01, SN: JAE11474EVC NAME: "0/6/4", DESCR: "8-port OC12/STM4 POS Shared Port Adapters" PID: SPA-8XOC12-POS , VID: V01, SN: JAB094706L9 NAME: "0/6/5", DESCR: "8-port Gigabit Ethernet Shared Port Adapter" PID: SPA-8X1GE , VID: V01, SN: SAD093909GM NAME: "0/RP0/*", DESCR: "Cisco CRS-1 Series 8 Slots Route Processor" PID: CRS-8-RP , VID: V01, SN: SAD093507HX --More--Table 1 describes the significant fields shown in the display.
Table 13 show inventory Field Descriptions Field
Description
NAME
Hardware for which the inventory information is displayed. If you are displaying the chassis inventory, this field shows “chassis.” If you are displaying raw inventory, or all inventory information for all nodes in the chassis, this field shows the node name in partially qualified format. For a node, the NAME is expressed in rack/slot/module notation.
DESCR
Describes the chassis or the node.
Chassis descriptions provide the name of the chassis and its Gbps. Node descriptions provide the type of node and its software version.
A description value of “CPU_PORT_0” indicates a control Ethernet port on the CPU module.
PID
Physical model name of the chassis or node.
VID
Physical hardware revision of the chassis or node.
SN
Physical serial number for the chassis or node.
show led
To display LED information for the router, or for a specific LED location, use the show led command in EXEC or administration EXEC mode.
Syntax Description
location {node-id | all} (Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The show led command was moved from the root-system task ID to the system task ID.
The show led command was supported in administration EXEC mode.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Enter the show platform command to see the location of all nodes installed in the router.
Task ID
Examples
The following example sample output from the show led command with the all keyword:
RP/0/RP0/CPU0:router# show led location all LOCATION MESSAGE MODE STATUS ================================================== 0/1/* IOS XR DEFAULT UNLOCKED 0/4/* ACTVDRP DEFAULT UNLOCKED 0/6/* IOS XR DEFAULT UNLOCKED 0/RP0/* ACTV RP DEFAULT UNLOCKED 0/RP1/* STBYRDY DEFAULT UNLOCKEDshow operational
To display all operational data provided as XML schema, use the show operational command in EXEC or administration EXEC mode.
Syntax Description
mda-class Name of the management data API (MDA) class to output. To specify a class name in hierarchy, all classes must be specified from the top of the class to the specific class name that you are interested in. MDA classes are case-sensitive.
To view all available MDA classes, use the question mark (?) online help function.
descriptive Displays more descriptive information.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Although the show operational command uses the schema database, the command displays the information in a string format like the other show commands. No XML related setups or knowledge is required to use the command.
Task ID
Examples
The following example shows sample output from the show operational command. Not all the output is shown.
RP/0/RP0/CPU0:router# show operational BGP DefaultVRF GlobalProcessInfo descriptive [BGP DefaultVRF GlobalProcessInfo] InStandaloneMode: true[Standalone or Distributed mode] RouterID: 0.0.0.0[Router ID for the local system] ConfiguredRouterID: 0.0.0.0[Configured router ID] LocalAS: 10[Local autonomous system #] RestartCount: 1[No of times BGP has started] ISRedistributeIBGPToIGPsEnabled: false[Redistribute iBGP into IGPs enabled] IsFastExternalFalloverEnabled: true[Fast external fallover enabled] IsBestpathMissingMEDIsWorstEnabled: false[Bestpath: Treat missing MED as worst] . . . DefaultLocalPreference: 100[Default local preference] KeepAliveTime: 60[Default keepalive timer (seconds)] HoldTime: 180[Default hold timer (seconds)] GenericScanPeriod: 60[Period (in seconds) of generic scanner runs] . . . VrfIsActive: true[VRF state ] VrfName: "default"[Name of the VRF ]This example shows sample output from the show operational command where only the top-level MDA class is specified. Not all of the output is shown.
RP/0/RP0/CPU0:router# show operational Inventory Thu Feb 19 00:54:41.251 PST [Inventory] RackTable Rack/Number=0 SlotTable Slot/Number=0 CardTable Card/Number=0 PortSlotTable PortSlot/Number=0 Port BasicAttributes BasicInfo Description: CPU_PORT_0 VendorType: 1.3.6.1.4.1.9.12.3.1.10 Name: 0/0/SP/0 IsFieldReplaceableUnit: false CompositeClassCode: 983040 BasicAttributes BasicInfo Description: CE Port Slot VendorType: 1.3.6.1.4.1.9.12.3.1.5.115 Name: portslot 0/0/SP/0 IsFieldReplaceableUnit: false CompositeClassCode: 0 SensorTable Sensor/Number=0 BasicAttributes BasicInfo Description: Temperature Sensor VendorType: 1.3.6.1.4.1.9.12.3.1.8.42 Name: 0/0/* - host - Inlet0 CompositeClassCode: 720898 EnvironmentalMonitorPath: /admin/oper/inventory/ rack/0/entity/0/entity/0/entity/0/entity/0/attrib/ Sensor/Number=1 BasicAttributes BasicInfo Description: Temperature Sensor VendorType: 1.3.6.1.4.1.9.12.3.1.8.42 Name: 0/0/* - host - Inlet1 CompositeClassCode: 720898 EnvironmentalMonitorPath: /admin/oper/inventory/ rack/0/entity/0/entity/0/entity/0/entity/1/attrib/ Sensor/Number=2 BasicAttributes BasicInfo Description: Temperature Sensor VendorType: 1.3.6.1.4.1.9.12.3.1.8.42 Name: 0/0/* - host - Exhaust0 CompositeClassCode: 720898 --More--show platform
To display information and status for each node in the system, use the show platform command in EXEC or administration EXEC mode.
Syntax Description
node-id (Optional) Node for which to display information. The node-id argument is entered in the rack/slot/module notation.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The show platform command was first supported in administration EXEC mode.
In EXEC mode, the show platform command was moved from the root-system task ID to the system task ID.
Release 4.0.1
Support was added for the MSC-140G.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show platform command provides a summary of the nodes in the system, including node type and status.
Enter the show platform command in administration EXEC mode to display output for the entire system. Enter the show platform command in EXEC mode to display output for only those nodes that belong to the SDR on which the command is executed.
Task ID
Examples
The following example shows sample output from the show platform command:
RP/0/RP0/CPU0:router# show platform Node Type PLIM State Config State ----------------------------------------------------------------------------- 0/1/CPU0 MSC Jacket Card IOS XR RUN PWR,NSHUT,MON 0/1/0 MSC(SPA) 4XOC3-POS OK PWR,NSHUT,MON 0/1/5 MSC(SPA) 8X1GE OK PWR,NSHUT,MON 0/6/CPU0 MSC Jacket Card IOS XR RUN PWR,NSHUT,MON 0/6/0 MSC(SPA) 4XOC3-POS OK PWR,NSHUT,MON 0/6/4 MSC(SPA) 8XOC3/OC12-POS OK PWR,NSHUT,MON 0/6/5 MSC(SPA) 8X1GE OK PWR,NSHUT,MON 0/RP0/CPU0 RP(Active) N/A IOS XR RUN PWR,NSHUT,MON 0/RP1/CPU0 RP(Standby) N/A IOS XR RUN PWR,NSHUT,MONThis example shows sample output from the show platform command on the Cisco CRS Series Modular Services Card 140G:
RP/0/RP0/CPU0:router# show platform 0/3/* Thu Aug 26 15:37:34.263 UTC ********************************************************************** ********** Router is running in Dual Router configuration ********** ********************************************************************** Node Type PLIM State Config State --------------------------------------------------------------------------------------- 0/3/CPU0 MSC-140G 20-10GbE IOS XR RUN PWR,NSHUT,NMONThe following is sample output for the show platform command with the node-id argument:
RP/0/RP0/CPU0:router# show platform 0/1/0 Node Type PLIM State Config State ----------------------------------------------------------------------------- 0/1/0 MSC(SPA) 4XOC3-POS OK PWR,NSHUT,MON
This table describes the significant fields shown in the display.
Table 15 show platform Field DescriptionsField
Description
Node
Identifier of the node in the rack/slot/module notation.
Type
Type of node.
PLIM
Type of physical layer interface module currently supported on the module.
State
Current state of the specified node.
Config State
Current status of the specified node.
show redundancy
Syntax Description
location {node-id | all} (Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.
statistics (Optional) Displays redundancy statistics information.
summary (Optional) Displays a summary of all redundant node pairs in the router.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.5.0
The statistics and trace keywords were added.
Release 3.6.0
Nonstop routing (NSR) indication was added to the command display.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show redundancy command to display the redundancy status of the route processors (RPs). The show redundancy command also displays the boot and switchover history for the RPs. To view the nonstop routing (NSR) status of the standby RPs in the system, use the summary keyword.
Task ID
Examples
The following example shows sample output from the show redundancy command:
RP/0/RP0/CPU0:router# show redundancy location 0/rp0/cpu0 Node 0/RP0/CPU0 is in ACTIVE role Partner node (0/RP1/CPU0) is in STANDBY role Standby node in 0/RP1/CPU0 is ready Standby node in 0/RP1/CPU0 is NSR-ready Reload and boot info ---------------------- RP reloaded Mon Jul 30 19:27:42 2007: 2 weeks, 1 day, 13 hours, 40 minutes ago Active node booted Mon Jul 30 19:27:42 2007: 2 weeks, 1 day, 13 hours, 40 minutes ago Standby node boot Mon Jul 30 19:28:13 2007: 2 weeks, 1 day, 13 hours, 39 minutes ago Standby node last went not ready Mon Jul 30 20:27:00 2007: 2 weeks, 1 day, 12 hours, 41 minutes ago Standby node last went ready Mon Jul 30 20:27:00 2007: 2 weeks, 1 day, 12 hours, 41 minutes ago There have been 0 switch-overs since reload
Table 16 show redundancy Field Descriptions Field
Description
Node */*/* is in XXX role
Current role of the primary route processor, where (*/*/*) is the route processor ID in the format rack/slot/module, and XXX is the role of the route processor (active or standby).
In the example, this field shows that the node with the ID 0/RP0/CPU0 is in active role.
Partner node (*/*/*) is in XXX role
Current role of the secondary (or partner) route processor, where (*/*/*) is the route processor ID in the rack/slot/module format, and XXX is the role of the route processor (active or standby).
In the example, this field shows that the node with the ID 0/RP1/CPU0 is in standby role.
Standby node in (*/*/*) is ready
Current state of the standby node, where (*/*/*) is the standby route processor ID.
In the example, the standby node is ready.
Standby node in (*/*/*) is NSR-ready
Current state of the standby node regarding nonstop routing (NSR), where (*/*/*) is the standby route processor ID.
In the example, the standby node is NSR-ready.
Reload and boot info
General overview of the active and standby route processors’ reload and boot history.
The following sample output shows the status of the redundant RPs in the system. The status of the standby node is indicated in parentheses next to the node identifier. The nonstop routing (NSR) status is indicated following NSR. Possible values are Ready and Not ready.
RP/0/RP0/CPU0:router# show redundancy summary Active Node Standby Node ---------- ------------ 0/4/CPU0 N/A 0/4/CPU1 N/A 0/RP0/CPU0 0/RP1/CPU0 (Ready, NSR: Ready)show screddrv
To display system controller (SC) redundancy information, use the show screddrv command in EXEC mode.
Syntax Description
all (Optional) Displays redundancy details for the entire router.
standby (Optional) Displays detailed redundancy information for the standby node.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.0
No modification.
Release 3.2
No modification.
Release 3.3.0
The show screddrv command was moved from the root-system task ID to the system task ID.
The arbitration keyword was removed from the show screddrv command.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Enter the show screddrv command without any of the optional parameters to display summarized SC redundancy and arbitration information for the router.
Task ID
Examples
The following is sample output from the show screddrv command with the all keyword:
RP/0/RP0/CPU0:router# show screddrv all Redundancy Driver Info for slot 32: Slot=32 Role=active role State=ACTIVE STATE Prefer_slot=0 Registers: ICreg=[1], MSreg=[33], MPPReg=[c0005cc8] Tx error count=0 Rx error count=22 Comm Statistics=5632 SHOW REDDRV ARBITRATION is not supported.show version
To display the configuration of the system hardware, the software version, the names and sources of configuration files, and the boot images, use the show version command in EXEC mode.
Command History
Release
Modification
Release 2.0
This command was introduced.
Release 3.3.0
The show version command was moved from the sysmgr task ID to the basic-services task ID.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show version command displays a variety of system information, including hardware and software version, router uptime, boot settings (configuration register), and active software.
Task ID
Examples
This example shows partial output from the show version command:
RP/0/RP0/CPU0:router# show version Cisco IOS XR Software, Version 3.4.0 Copyright (c) 2006 by cisco Systems, Inc. ROM: System Bootstrap, Version 1.32(20050525:193559) [CRS-1 ROMMON], CRS-8_P1 uptime is 1 week, 22 hours, 27 minutes System image file is "disk0:hfr-os-mbi-3.3.90/mbihfr-rp.vm" cisco CRS-8/S (7457) processor with 4194304K bytes of memory. 7457 processor at 1197Mhz, Revision 1.2 16 Packet over SONET/SDH network interface(s) 16 SONET/SDH Port controller(s) 2 Ethernet/IEEE 802.3 interface(s) 16 GigabitEthernet/IEEE 802.3 interface(s) 2043k bytes of non-volatile configuration memory. 38079M bytes of hard disk. 1000592k bytes of ATA PCMCIA card at disk 0 (Sector size 512 bytes). 1000640k bytes of ATA PCMCIA card at disk 1 (Sector size 512 bytes). Package active on node 0/1/SP: hfr-diags, V 3.3.90[1I], Cisco Systems, at disk0:hfr-diags-3.3.90 Built on Mon Mar 27 12:29:00 UTC 2006 By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8 hfr-admin, V 3.3.90[1I], Cisco Systems, at disk0:hfr-admin-3.3.90 Built on Mon Mar 27 09:22:26 UTC 2006 By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8 hfr-base, V 3.3.90[1I], Cisco Systems, at disk0:hfr-base-3.3.90 Built on Mon Mar 27 09:13:04 UTC 2006 By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8 hfr-os-mbi, V 3.3.90[1I], Cisco Systems, at disk0:hfr-os-mbi-3.3.90 Built on Mon Mar 27 08:34:13 UTC 2006 By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8 --More--
Table 18 show version Field Descriptions Field
Description
Cisco IOS XR Software, Version #
Cisco IOS XR software version number currently running on the router.
ROM
System bootstrap version number currently running on the router.
router uptime
Number of uninterrupted days, hours, minutes, and seconds the system has been up and running.
System image file is
Location and name of the system image file currently running on the router.
Packet over SONET/SDH network interface(s)
Number of Packet-over-SONET/SDH interfaces available on the current router.
SONET/SDH Port controller(s)
Number of SONET or SDH1 interfaces available on the current router.
Ethernet/IEEE 802.3 interface(s)
Number of Ethernet or IEEE 802.3 interfaces available on the current router.
GigabitEthernet/IEEE interface(s)
Number of Gigabit Ethernet or IEEE 802.3 interfaces available on the current router.
bytes of non-volatile configuration memory
Available volatile configuration memory, in bytes.
bytes of ATA PCMCIA card at disk 0
ATA PCMCIA2 available on the card in disk 0, in bytes.
Package active on node 0/1/SP
Details about the current software package that is running on the SP node in slot 1.
1 SDH = Synchronous Digital Hierarchy2 ATA PCMCIA = AT Attachment Personal Computer Memory Card Industry Associationupgrade cpuctrlbits
To upgrade the CPU controller bits on all nodes that are installed in the router or on a specific node, use the upgrade cpuctrlbits command in administration EXEC mode.
Syntax Description
all Upgrades the CPU controller bits on all nodes installed in the router.
location node-id Upgrades the CPU controller bits on a specific node. The node-id is expressed in the rack/slot/module notation.
Note Enter the show platform command to see the location of all nodes installed in the router.
bootflash (Optional) Uses the images located on the bootflash to upgrade the CPU controller on all nodes, or on the specified node.
disk0 (Optional) Uses the images located on disk0 to upgrade the CPU controller on all nodes, or on the specified node.
disk1 (Optional) Uses the images located on disk1 to upgrade the CPU controller on all nodes, or on the specified node.
internal (Optional) Uses the images located in the /pkg/bin.
Note This is the default location for the ROMMON image.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
The upgrade cpuctrlbits command was moved from the sysmgr task ID to the system task ID.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The upgrade cpuctrlbits command is only applicable to boards that use the Squid CPU controller, and not the Squirt controller. Use the internal keyword to determine which CPU controller is used in a specific card, as indicated in bold in the following example:
RP/0/RP0/CPU0:router# show controller cpuctrl internal Cpuctrl Internal Info for node 0/1/CPU0: Error Interrupts = 0 Spurious Error Interrupts = 0 PCI Error Overflows = 0 PCI PM Error Overflows = 0 PCIX Error Overflows = 0 Internal Access PCI Overflows = 0 Port Error Overflows = 0 Error Log Overflows = 0 cpuctrl Config Reg = 0x8357ffff cpuctrl Physical Offset = 0x80000000 cpuctrl Window Size = 0x40000000 cpuctrl Port Window Size = 0x04000000 cpuctrl SHMem Size = 0x00800000 cpuctrl SHMem Used = 0x00224fb0 cpuctrl version info: Squid FPGA v2.07 Fri Jan 23 16:21:01 2004 ykoren Cpuctrl Internal Info for node 0/4/CPU0: Error Interrupts = 0 Spurious Error Interrupts = 0 PCI Error Overflows = 0 PCI PM Error Overflows = 0 PCIX Error Overflows = 0 Internal Access PCI Overflows = 0 Port Error Overflows = 0 Error Log Overflows = 0 cpuctrl Config Reg = 0xffffffff cpuctrl Physical Offset = 0x80000000 cpuctrl Window Size = 0x40000000 cpuctrl Port Window Size = 0x04000000 cpuctrl SHMem Size = 0x00800000 cpuctrl SHMem Used = 0x00224fb0 cpuctrl version info: SQUIRT v3 . . .Task ID
Examples
This example shows how to upgrade the CPU controller bits on all nodes in a router:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# upgrade cpucrtlbits all Please do not power cycle, reload the router or reset any nodes until all upgrades are completed. Please check the syslog to make sure that all nodes are upgraded successfully. If you need to perform multiple upgrades, please wait for current upgrade to be completed before proceeding to another upgrade. Failure to do so may render the cards under upgrade to be unusable.upgrade hw-module fpd
To manually upgrade the current field-programmable device (FPD) image package on a module, use the upgrade hw-module fpd command in administration EXEC mode.
Syntax Description
all
Upgrades all FPD images on the selected module.
fabldr
Upgrades the fabric-downloader FPD image on the module.
fpga-type
Upgrades a specific field-programmable gate array (FPGA) image on the module. Use the show fpd package command to view all available FPGA images available for a specific module.
rommon
Upgrades the ROMMON image on the module.
force
(Optional) Forces the update of the indicated FPD image package on a shared port adapter (SPA) that meets the minimum version requirements. Without this option, the manual upgrade upgrades only incompatible FPD images.
location {node-id | all} Specifies the node for which to upgrade the FPD image. The node-id argument is expressed in the rack/slot/subslot notation. Use the all keyword to indicate all nodes.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
Support for multiple FPGA images was added.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
During the upgrade procedure, the module must be offline (shut down but powered).
Naming notation for the node-id argument is rack/slot/subslot; a slash between values is required as part of the notation.
- rack —Chassis number of the rack.
- slot —Physical slot number of the SPA interface processor (SIP).
- subslot —Subslot number of the SPA.
For more information about the syntax for the router, use the question mark (?) online help function.
When you start the FPD upgrade procedure or log into a router that is running the FPD upgrade procedure, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those is not recommended as it might cause HW programming failure and result in RMA of the hardware.If you enter administration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those is not recommended as it might cause HW programming failure and result in RMA of the hardware. Do you want to continue? [Confirm (y/n)]If you enter global configuration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, configuration change on those is not recommended as it might cause HW programming failure and result in RMA of the hardware. Do you want to continue? [Confirm (y/n)]When the FPD upgrade global timer expires, the following warning message displayed to the screen.
FPD upgrade has exceeded the maximum time window, the process will terminate now. Please check the status of the hardware and reissue the upgrade command if required.Task ID
Examples
The following example shows how to upgrade the default FPGA on a SPA:
RP/0/RP0/CPU0:router# admin RP/0/RP0/CPU0:router(admin)# upgrade hw-module fpd fpga force location 0/1/4 % RELOAD REMINDER: - The upgrade operation of the target module will not interrupt its normal operation. However, for the changes to take effect, the target module will need to be manually reloaded after the upgrade operation. This can be accomplished with the use of "hw-module <target> reload" command. - If automatic reload operation is desired after the upgrade, please use the "reload" option at the end of the upgrade command. - The output of "show hw-module fpd location" command will not display correct version information after the upgrade if the target module is not reloaded. Continue? [confirm] y SP/0/1/SP:Dec 22 05:41:17.920 : upgrade_daemon[125]: programming...with file /net/node0_RP1_CPU0/hfr-lc-3.3.83/fpd/ucode/fpga_gladiator_sw0.6.xsvf SP/0/1/SP:Dec 22 05:41:28.900 : upgrade_daemon[125]: ...programming... SP/0/1/SP:Dec 22 05:41:28.906 : upgrade_daemon[125]: ...it will take a while... SP/0/1/SP:Dec 22 05:41:29.004 : upgrade_daemon[125]: ...it will take a while... SP/0/1/SP:Dec 22 05:43:03.432 : upgrade_daemon[125]: ...programming... SP/0/1/SP:Dec 22 05:43:03.438 : upgrade_daemon[125]: ...it will take a while... Successfully upgraded spa fpga instance 4 on location 0/1/4.Related Commands
Command
Description
Displays the FPD compatibility for all modules or a specific module.
Displays which FPD image package is needed for the router to properly support the modules for the running Cisco IOS XR software release. Also indicates all available FPD images that are available for a specific module.
