Table Of Contents

Unsupported Commands in Cisco IOS Release 12.2(58)EZ

Access Control List Commands

Unsupported Global Configuration Commands

Unsupported Privileged EXEC Commands

ARP Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Boot Loader Commands

Unsupported Global Configuration Command

Unsupported User EXEC Command

Debug Commands

Embedded Event Manager Commands

Unsupported Applet Configuration Commands

Unsupported Global Configuration Commands

Unsupported Privileged EXEC Commands

HSRP Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

IEEE 802.1x Commands

Unsupported Interface Configuration Commands

Unsupported Privileged EXEC Commands

IGMP Snooping Commands

Unsupported Global Configuration Commands

Interface Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Unsupported Privileged EXEC Commands

IP Multicast Routing Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Unsupported Privileged EXEC Commands

IP Unicast Routing Commands

Unsupported BGP Router Configuration Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Unsupported Privileged EXEC or User EXEC Commands

Unsupported Route Map Commands

Unsupported VPN Configuration Commands

MAC Address Commands

Unsupported Global Configuration Commands

Unsupported Privileged EXEC Commands

Miscellaneous Commands

Unsupported Global Configuration Commands

Unsupported Privileged EXEC Commands

Unsupported show platform Commands

Unsupported User EXEC Commands

MSDP Commands

Unsupported Global Configuration Commands

Unsupported Privileged EXEC Commands

NetFlow Commands

Unsupported Global Configuration Commands

QoS Commands

Unsupported Global Configuration Command

Unsupported Interface Configuration Command

Unsupported policy-map Class Police Configuration Mode Command

RADIUS Commands

Unsupported Global Configuration Commands

SNMP Commands

Unsupported Global Configuration Commands

Spanning Tree Commands

Unsupported Global Configuration Command

Unsupported Interface Configuration Command

VLAN Commands

Unsupported Global Configuration Command

Unsupported User EXEC Commands

Unsupported VLAN Database Commands

Unsupported Commands in Cisco IOS Release 12.2(58)EZ

---

This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the CGR 2010 ESM switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode.

This appendix contains the following topics:

•Access Control List Commands

•ARP Commands

•Boot Loader Commands

•Debug Commands

•Embedded Event Manager Commands

•HSRP Commands

•IEEE 802.1x Commands

•IGMP Snooping Commands

•Interface Commands

•IP Multicast Routing Commands

•IP Unicast Routing Commands

•MAC Address Commands

•Miscellaneous Commands

•MSDP Commands

•NetFlow Commands

•QoS Commands

•RADIUS Commands

•SNMP Commands

•Spanning Tree Commands

•VLAN Commands

Access Control List Commands

Unsupported Global Configuration Commands

access-list rate-limit acl-index {precedence | mask prec-mask}

access-list dynamic extended

Unsupported Privileged EXEC Commands

access-enable [host] [timeout minutes]

access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]

clear access-template [access-list-number | name] [dynamic-name] [source] [destination].

ARP Commands

Unsupported Global Configuration Commands

arp ip-address hardware-address smds

arp ip-address hardware-address srp-a

arp ip-address hardware-address srp-b

Unsupported Interface Configuration Commands

arp probe

ip probe proxy

Boot Loader Commands

Unsupported Global Configuration Command

boot buffersize

Unsupported User EXEC Command

verify

Debug Commands

debug dot1x feature

debug platform cli-redirection main

debug platform configuration

debug qos

Embedded Event Manager Commands

Unsupported Applet Configuration Commands

no event interface name [interface-name] parameter [counter-name] entry-val [entry counter value] entry-op {gt | ge | eq | ne |lt | le} [entry-type {increment | rate | value] [exit-val [exit value] exit-op {gt | ge | eq | ne |lt | le} exit-type { increment | rate | value}][average-factor <average-factor-value>]

no trigger

tag

Unsupported Global Configuration Commands

no event manager directory user repository [url location]

event manager applet [applet-name] maxrun

Unsupported Privileged EXEC Commands

event manager update user policy [policy-filename | group [group name expression] ] | repository [url location]

Parameters are not supported for this command:

event manager run [policy name] |<paramater1>|... <paramater15>|

HSRP Commands

Unsupported Global Configuration Commands

interface Async

interface BVI

interface Dialer

interface Group-Async

interface Lex

interface Multilink

interface Virtual-Template

interface Virtual-Tokenring

Unsupported Interface Configuration Commands

mtu

standby mac-refresh seconds

standby use-bia

IEEE 802.1x Commands

Unsupported Interface Configuration Commands

dot1x credentials

---

Note The dot1x credentials profile global configuration command is still supported.

---

dot1x max-start

Unsupported Privileged EXEC Commands

clear eap sessions

dot1x re-authenticate

show eap

IGMP Snooping Commands

Unsupported Global Configuration Commands

ip igmp snooping source-only-learning

Interface Commands

Unsupported Global Configuration Commands

interface tunnel

Unsupported Interface Configuration Commands

power inline port priority high | low

transmit-interface type number

Unsupported Privileged EXEC Commands

show interfaces [interface-id | vlan vlan-id] [crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape]

IP Multicast Routing Commands

Unsupported Global Configuration Commands

All ip dvmrp commands

ip multicast-routing vrf vrf-name

ip pim accept-rp {address | auto-rp} [group-access-list-number]

ip pim message-interval seconds

ip pim register-rate-limit

Unsupported Interface Configuration Commands

frame-relay ip rtp header-compression [active | passive]

frame-relay map ip ip-address dlci [broadcast] compress

frame-relay map ip ip-address dlci rtp header-compression [active | passive]

All ip dvmrp commands

ip igmp helper-address ip-address

ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number

ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps

ip multicast ttl-threshold ttl-value (instead, use the ip multicast boundary access-list-number interface configuration command)

ip multicast use-functional

ip pim minimum-vc-rate pps

ip pim multipoint-signalling

ip pim nbma-mode

ip pim vc-count number

ip rtp compression-connections number

ip rtp header-compression [passive]

Unsupported Privileged EXEC Commands

clear ip rtp header-compression [type number]

clear ip dvmrp route commands

debug ip dvmrp commands

The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU.

debug ip pim atm

show frame-relay ip rtp header-compression [interface type number]

show ip dvmrp route commands

The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed.

The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardware-switched, the command has no effect because the CPU does not receive the packet and cannot display it.

show ip pim vc [group-address | name] [type number]

show ip rtp header-compression [type number] [detail]

IP Unicast Routing Commands

Unsupported BGP Router Configuration Commands

address-family vpnv4

default-information originate

neighbor advertise-map

neighbor allowas-in

neighbor default-originate

neighbor description

network backdoor

table-map

Unsupported Global Configuration Commands

ip accounting-list ip-address wildcard

ip as-path access-list

ip accounting-transits count

ip cef accounting [per-prefix] [non-recursive]

ip cef traffic-statistics [load-interval seconds] [update-rate seconds]]

ip flow-aggregation

ip flow-cache

ip flow-export

ip gratuitous-arps

ip local

ip prefix-list

ip reflexive-list

router egp

router-isis

router iso-igrp

router mobile

router odr

router static

Unsupported Interface Configuration Commands

dampening

ip load-sharing [per-packet]

ip accounting

ip load-sharing [per-packet]

ip mtu bytes

ip ospf dead-interval minimal hello-multiplier multiplier

ip verify

ip unnumbered type number

All ip security commands

Unsupported Privileged EXEC or User EXEC Commands

clear ip accounting [checkpoint]

clear ip bgp address flap-statistics

clear ip bgp prefix-list

debug ip cef stats

show cef [drop | not-cef-switched]

show ip accounting [checkpoint] [output-packets | access-violations]

show ip bgp dampened-paths

show ip bgp inconsistent-as

show ip bgp regexp regular expression

show ip prefix-list regular expression

show ipv6 (all)

Unsupported Route Map Commands

match route-type for policy-based routing (PBR)

set as-path {tag | prepend as-path-string}

set automatic-tag

set dampening half-life reuse suppress max-suppress-time

set default interface interface-id [interface-id.....]

set interface interface-id [interface-id.....]

set ip default next-hop ip-address [ip-address.....]

set ip destination ip-address mask

set ip precedence value

set ip qos-group

set metric-type internal

set origin

set metric-type internal

set tag tag-value

Unsupported VPN Configuration Commands

All

MAC Address Commands

Unsupported Global Configuration Commands

mac-address-table aging-time

mac-address-table notification

mac-address-table static

Unsupported Privileged EXEC Commands

show mac-address-table

show mac-address-table address

show mac-address-table aging-time

show mac-address-table count

show mac-address-table dynamic

show mac-address-table interface

show mac-address-table multicaset

show mac-address-table notification

show mac-address-table static

show mac-address-table vlan

show mac address-table multicast

---

Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.

---

Miscellaneous Commands

Unsupported Global Configuration Commands

exception crashinfo

errdisable detect cause dhcp-rate-limit

errdisable recovery cause dhcp-rate-limit

errdisable recovery cause unicast flood

l2protocol-tunnel global drop-threshold

memory reserve critical

power inline consumption default wattage

service compress-config

Unsupported Privileged EXEC Commands

archive config

file verify auto

remote command all

show archive config

show archive log

show cable-diagnostics prbs

show power inline

test cable-diagnostics prbs

stack-mac persistent timer

track object-number rtr

Unsupported show platform Commands

show platform ip unicast vrf {compaction | tcam-label}

show platform ipv6 unicast

show platform tb

Unsupported User EXEC Commands

verify

MSDP Commands

Unsupported Global Configuration Commands

ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)

Unsupported Privileged EXEC Commands

show access-expression

show exception

show location

show pm LINE

show smf [interface-id]

show subscriber-policy [policy-number]

show template [template-name]

NetFlow Commands

Unsupported Global Configuration Commands

ip flow-aggregation cache

ip flow-cache entries

ip flow-export

QoS Commands

Unsupported Global Configuration Command

priority-list

Unsupported Interface Configuration Command

priority-group

Unsupported policy-map Class Police Configuration Mode Command

conform-color class-map police configuration

RADIUS Commands

Unsupported Global Configuration Commands

aaa authentication feature default enable

aaa authentication feature default line

aaa nas port extended

authentication command bounce-port ignore

authentication command disable-port ignore

radius-server attribute nas-port

radius-server configure

radius-server extended-portnames

SNMP Commands

Unsupported Global Configuration Commands

snmp-server enable informs

snmp-server ifindex persist

Spanning Tree Commands

Unsupported Global Configuration Command

spanning-tree pathcost method {long | short}

spanning-tree transmit hold-count

Unsupported Interface Configuration Command

spanning-tree stack-port

VLAN Commands

Unsupported Global Configuration Command

vlan internal allocation policy {ascending | descending}

Unsupported User EXEC Commands

show running-config vlan

show vlan ifindex

vlan database

Unsupported VLAN Database Commands

vtp

vlan