Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference, Release 4.2.x - Integrated Routing and Bridging Commands on the Cisco ASR 9000 Series Router [Cisco ASR 9000 Series Aggregation Services Routers]

Contents

Integrated Routing and Bridging Commands on the Cisco ASR 9000 Series Router

interface bvi

routed interface bvi

show interfaces bvi

Integrated Routing and Bridging Commands on the Cisco ASR 9000 Series Router

This module describes the commands to configure Integrated Routing and Bridging (IRB) on the Cisco ASR 9000 Series Router.

interface bvi
routed interface bvi
show interfaces bvi
interface bvi
To create a bridge-group virtual interface (BVI), use the interface bvi command in global configuration mode. To delete the BVI, use the no form of this command.

interface bvi identifier
no interface bvi identifier

Syntax Description

identifier
Number for the BVI interface from 1 to 65535.

Command Default

No BVI interface is configured.

Command Modes

Global configuration (config)

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The BVI is a virtual interface within the router that acts like a normal routed interface. The BVI does not support bridging itself, but acts as a gateway for the corresponding bridge-domain to a routed interface within the router.

Aside from supporting a configurable MAC address, a BVI supports only Layer 3 attributes, and has the following characteristics:

Uses a MAC address taken from the local chassis MAC address pool, unless overridden at the BVI interface.

Is configured as an interface type using the interface bvi command and uses an IPv4 or IPv6 address that is in the same subnet as the hosts on the segments of the bridged domain. The BVI also supports secondary addresses.

The BVI identifier is independent of the bridge-domain identifier. These identifiers do not need to correlate like they do in Cisco IOS software.

Is associated to a bridge group using the routed interface bvi command.

The following interface commands are supported on a BVI:
arp purge-delay

arp timeout

bandwidth (The default is 10 Gbps and is used as the cost metric for routing protocols for the BVI.)

ipv4

ipv6 (Supported on Gigabit Ethernet line cards only in Cisco IOS XR Release 4.1)

mac-address

mtu (The default is 1514 bytes.)

shutdown

The BVI supports IP helper addressing and secondary IP addressing.

To display bridge group, bridge-domain, interface status, line protocol state, and packet counters for the specified BVI, use the show l2vpn bridge domain interface bvi form of the show l2vpn bridge domain (VPLS) command. To display the reason that a BVI is down, you can use the detail keyword option.

Task ID

Task ID Operation

interface

read, write
Examples

The following example shows how to create a BVI interface and configure its IPv4 address:
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface bvi 50
RP/0/RSP0/CPU0:router(config-if)# ipv4 address 10.10.0.4 255.255.255.0
RP/0/RSP0/CPU0:router(config-if)# commit
Related Commands

Command
Description
routed interface bvi
Associates the specified bridge group virtual interface (BVI) as the routed interface for the interfaces assigned to the bridge domain.
show interfaces bvi
Displays interface status, line protocol state, and packet counters for the specified BVI.
show adjacency

show l2vpn bridge-domain (VPLS)
Display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains.
routed interface bvi
To associate the specified bridge group virtual interface (BVI) as the routed interface for the interfaces assigned to the bridge domain, use the routed interface bvi command in L2VPN bridge group bridge domain configuration mode. To remove the BVI as the routed interface for the interfaces assigned to the bridge domain, use the no form of this command.

routed interface bvi identifier
no routed interface bvi identifier

Syntax Description

identifier
Number for the BVI interface from 1 to 65535.

Command Default

No routed interface is configured.

Command Modes

L2VPN bridge group bridge domain configuration mode (config-l2vpn-bg-bd)

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Only one BVI can be configured in any bridge domain.

The same BVI can not be configured in multiple bridge domains.

Task ID

Task ID Operation

l2vpn

read, write
Examples

The following example shows association of a BVI interface numbered “50” on the bridge domain named “IRB”:
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group 10
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain IRB
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# routed interface bvi 50
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# commit
Related Commands

Command
Description
interface bvi
Creates a BVI interface.
l2vpn
Enters L2VPN configuration mode.
bridge group (VPLS)
Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
bridge-domain (VPLS)
Establishes a bridge domain and enters L2VPN bridge group bridge domain configuration mode.
show interfaces bvi
Displays interface status, line protocol state, and packet counters for the specified BVI.
show adjacency

show l2vpn bridge-domain (VPLS)
Display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains.
show interfaces bvi
To display interface status, line protocol state, and packet counters for the specified BVI, use the show interfaces bvi command in EXEC mode.

show interfaces bvi identifier [ accounting | brief | description | detail | location location ]

Syntax Description

identifier
Number for the BVI interface from 1 to 65535.

accounting
(Optional) Displays the number of packets of each protocol type that have been sent through the interface.

brief
(Optional) Displays summary information about the interface.

description
(Optional) Displays summary status information and the description for the interface.

detail
(Optional) Displays detailed information about the interface. This is the default.

location location
(Optional) Displays information the interface on the specified node. The location argument is entered in the rack/slot/module notation.

Command Default

Detailed information about the BVI interface is displayed.

Command Modes

EXEC (#)

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

interface

read
Examples

The following example shows sample output for the show interfaces bvi command:
RP/0/RSP0/CPU0:router# show interfaces bvi 50
Wed Feb 16 16:05:11.508 PST
BVI50 is up, line protocol is up 
  Interface state transitions: 3
  Hardware is Bridge-Group Virtual Interface, address is 0000.0000.0002
  Description: IRB Routed Example
  Internet address is 172.16.0.1/24
  MTU 9014 bytes, BW 10000000 Kbit (Max: 10000000 Kbit)
     reliability 255/255, txload 0/255, rxload 0/255
  Encapsulation ARPA,  loopback not set,
  ARP type ARPA, ARP timeout 04:00:00
  Last input 00:00:37, output 00:00:00
  Last clearing of "show interface" counters never
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     25643 packets input, 1641152 bytes, 0 total input drops
     0 drops for unrecognized upper-level protocol
     Received 0 broadcast packets, 25445 multicast packets
     208 packets output, 9472 bytes, 0 total output drops
     Output 8 broadcast packets, 0 multicast packets
Table 1 show interfaces bvi Field Descriptions
Field

Description

BVIx is

Displays the state of the specified BVI interface, where x is the number of the interface. The possible values are: administratively down, down, or up.

line protocol is

Displays the stateof the line protocol for the BVI interface. The possible values are: administratively down, down, or up.

Note
The line protocol state is not the same as the protocol state displayed in the show ip interfaces command, because it is the state of Layer 2 (media) rather than Layer 3 (IP protocol).

Interface state transitions:

Displays the number of times the interface has changed states.

Hardware is

Displays Bridge-Group Virtual Interface for a BVI.

address is

Layer 2 MAC address of the BVI.

Description:

Displays the description of the interface when configured.

Internet address is n.n.n.n/n

Layer 3 IP address of the BVI in dotted decimal format.

MTU

Displays the maximum transmission unit (MTU) for the interface. The MTU is the maximum packet size that can be transmitted over the interface.
1514 is the default.

BW x Kbit

Displays the current bandwidth of the interface in kilobits per second.

Max:

Displays the maximum bandwidth available on the interface in kilobits per second.

reliability

Displays the proportion of packets that are not dropped and do not have errors.

Note
The reliability is shown as a fraction of 255.

txload

Indicates the traffic flowing out of the interface as a proportion of the bandwidth.

Note
The txload is shown as a fraction of 255.

rxload

Indicates the traffic flowing into the interface as a proportion of the bandwidth.

Note
The rxload is shown as a fraction of 255.

Encapsulation

Layer 2 encapsulation on the interface.

loopback

Always displays “not set” for a BVI because loopbacks are not supported.

ARP type

Address Resolution Protocol (ARP) type used on the interface.

ARP timeout

ARP timeout in the format hours:mins:secs. This value is configurable using the arp timeout command.

Last input

Number of hours, minutes, and seconds since the last packet was successfully received by an interface and processed locally on the router. Useful for knowing when a dead interface failed.

output

Number of hours, minutes, and seconds since the last packet was successfully transmitted by the interface. Useful for knowing when a dead interface failed.

Last clearing of “show interface” counters

Time since the counters in this command were last cleared using the clear counters Exec command in hours:mins:secs.

5 minute input rate

Average number of bits and packets received per second in the last 5 minutes. If the interface is not in promiscuous mode, it senses network traffic that it sends and receives (rather than all network traffic).

Note
The 5-minute period referenced in the command output is a load interval that is configurable under the interface. The default value is 5 minutes.

Note
The 5-minute input should be used only as an approximation of traffic per second during a given 5-minute period. This rate is exponentially weighted average with a time constant of 5 minutes. A period of four time constants must pass before the average will be within two percent of the instantaneous rate of a uniform stream of traffic over that period.

5 minute output rate

Average number of bits and packets transmitted per second in the last 5 minutes. If the interface is not in promiscuous mode, it senses network traffic that it sends and receives (rather than all network traffic).

Note
The 5-minute period referenced in the command output is a load interval that is configurable under the interface. The default value is 5 minutes.

Note
The 5-minute output should be used only as an approximation of traffic per second during a given 5-minute period. This rate is exponentially weighted average with a time constant of 5 minutes. A period of four time constants must pass before the average will be within two percent of the instantaneous rate of a uniform stream of traffic over that period.

packets input

Number of packets received on the interface that were successfully delivered to higher layers.

bytes

Number of bytes received on the interface.

total input drops

Total number of valid packets that were dropped after they were received. This includes packets that were dropped due to configured quality of service (QoS) or access control list (ACL) policies. This does not include drops due to unknown Layer 3 protocol.

drops for unrecognized upper-level protocol

Total number of packets that could not be delivered because the necessary protocol was not configured on the interface.

Received x broadcast packets

Total number of Layer 2 broadcast packets received on the interface. This is a subset of the total input packet count.

multicast packets

Total number of Layer 2 multicast packets received on the interface. This is a subset of the total input packet count.

packets output

Number of packets sent from the interface.

bytes

Total number of bytes successfully sent from the interface.

total output drops

Number of packets that were dropped before being transmitted.

Output x broadcast packets

Number of Layer 2 broadcast packets transmitted on the interface. This is a subset of the total output packet count.

multicast packets

Total number of Layer 2 multicast packets received on the interface. This is a subset of the total output packet count.

Related Commands

Command
Description
interface bvi
Creates a BVI interface.
show l2vpn bridge-domain (VPLS)
Display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains.