Table Of Contents
Cisco MC3810-IGX Interworking Commands
connect
Syntax Description
Defaults
Command Mode
Command History
Usage Guidelines
Examples
Related Commands
connect voice
Syntax Description
Defaults
Command Mode
Command History
Examples
Related Commands
encapsulation ftc-trunk
Syntax Description
Defaults
Command Mode
Command History
Examples
Related Commands
ftc-trunk frame-relay-dlci
Syntax Description
Defaults
Command Mode
Command History
Usage Guidelines
Examples
Related Commands
ftc-trunk management-dlci
Syntax Description
Defaults
Command Mode
Command History
Usage Guidelines
Examples
Related Commands
ftc-trunk management-protocol
Syntax Description
Defaults
Command Mode
Command History
Usage Guidelines
Examples
Related Commands
ftc-trunk voice-dlci
Syntax Description
Defaults
Command Mode
Command History
Usage Guidelines
Examples
Related Commands
Cisco MC3810-IGX Interworking Commands
This chapter describes the commands and command syntax used to configure Cisco MC3810-IGX Interworking on the Cisco MC3810.
The following are the Cisco MC3810-IGX Interworking commands:
•
connect
•connect voice
•encapsulation ftc-trunk
•ftc-trunk frame-relay-dlci
•ftc-trunk management-dlci
•ftc-trunk management-protocol
•ftc-trunk voice-dlci
connect
To configure a data connection that will travel over the FTC trunk to an IGX switch, use the connect global configuration command. To cancel the connection, use the no form of this command.
connect interface dlci dlci ftc-trunk connection-id cid
no connect interface dlci dlci ftc-trunk connection-id cid
Syntax Description
interface
|
Interface on the Cisco MC3810 on which the connection is configured.
|
dlci
|
DLCI for the connection.
|
ftc-trunk
|
Cisco MC3810 interface on which the FTC trunk was configured.
|
cid
|
Connection ID.
|
Defaults
No data connection over the FTC trunk is configured.
Command Mode
Global configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Usage Guidelines
When configuring a connection for an IP routing data connection over an FTC trunk, specify Switch0 for the local interface value.
When entering the DLCI value, do not use either of the following DLCIs:
•The DLCI that was assigned to the FTC management DLCI using the ftc-trunk management-dlci command
•The DLCI that was assigned to the FTC Frame Relay DLCI using the ftc-trunk frame-relay-dlci command.
Examples
The following example establishes a data connection on serial port 1:
connect Serial1 dlci 250 Serial0:0 connection-id 250
Related Commands
Command
|
Description
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
connect voice
To configure a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk, use the connect voice global configuration command. To disable the connection, use the no form of this command.
connect voice dial-peer-tag ftc-trunk connection-id cid
no connect voice dial-peer-tag ftc-trunk connection-id cid
Syntax Description
dlal-peer-tag
|
Voice dial-peer tag for the connection. Valid entries are 1 to 10000. The dial peer can be either a POTS dial peer or a VoFR dial peer.
|
ftc-trunk
|
Cisco MC3810 interface on which the FTC trunk was configured.
|
connection-id cid
|
Connection ID.
|
Defaults
No voice connection over the FTC trunk is configured.
Command Mode
Global configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Examples
The following example establishes a voice connection for dial peer 2 on serial port 0:
connect Voice2 Serial0:0 connection-id 50
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
encapsulation ftc-trunk
To enable FTC trunk encapsulation on a serial interface on the Cisco MC3810, use the encapsulation ftc-trunk interface configuration command. To disable FTC trunk encapsulation, use the no form of this command.
encapsulation ftc-trunk
no encapsulation ftc-trunk
Syntax Description
This command has no keywords or arguments.
Defaults
FTC trunk encapsulation is not enabled.
Command Mode
Interface configuration.
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Examples
To configure FTC trunk encapsulation on serial interface 1 on the Cisco MC3810, enter the following commands:
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
ftc-trunk frame-relay-dlci
To map the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810, use the ftc-trunk frame-relay-dlci interface configuration command. To remove the FTC Frame Relay DLCI from the interface, use the no form of this command.
ftc-trunk frame-relay-dlci dlci [remote-frame-relay-dlci dlci]
no ftc-trunk frame-relay-dlci dlci [remote-frame-relay-dlci dlci]
Syntax Description
dlci
|
Specifies the Frame Relay DLCI for the IGX switch.
|
remote-frame-relay-dlci dlci
|
(Optional) Specifies the remote Frame Relay DLCI if there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same.
|
Defaults
No FTC trunk Frame Relay DLCI is configured.
Command Mode
Interface configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Usage Guidelines
Do not enter the same DLCI that was assigned to the FTC management DLCI using the ftc-trunk management-dlci command.
Examples
The following example configures DLCI 200 as the FTC trunk Frame Relay DLCI:
ftc-trunk frame-relay-dlci 200
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
To map the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810, use the ftc-trunk management-dlci interface configuration command. To remove the FTC management DLCI from the interface, use the no form of this command.
ftc-trunk management-dlci dlci [remote-management-dlci dlci]
no ftc-trunk management-dlci dlci [remote-management-dlci dlci]
Syntax Description
dlci
|
Specifies the Frame Relay DLCI for the IGX switch.
|
remote-management-dlci dlci
|
(Optional) Specifies the remote management DLCI if there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same.
|
Defaults
No FTC trunk management DLCI is configured.
Command Mode
Interface configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Usage Guidelines
The DLCI (or the remote DLCI if configured) must match the DLCI on the IGX switch configured using the IGX addad command.
Examples
The following example configures DLCI 100 as the FTC trunk management DLCI:
ftc-trunk management-dlci 100
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
To select the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI, use the ftc-management-protocol interface configuration command. To restore the default value, use the no form of this command.
ftc-trunk management-protocol {normal | inverted}
no ftc-trunk management-protocol {normal | inverted}
Syntax Description
normal
|
Normal mode.
|
inverted
|
Inverted mode.
|
Defaults
Normal mode is enabled.
Command Mode
Interface configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Usage Guidelines
Use normal mode when the Cisco MC3810 is connected directly to the IGX switch. When two Cisco MC3810 concentrators are connected back-to-back, use inverted mode on one concentrator and normal mode on the other concentrator.
This command is available only when the ftc-trunk management-dlci command is configured.
Examples
The following example configures the FTC trunk management protocol to normal mode:
ftc-trunk management-dlci 100
ftc-trunk management-protocol normal
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk voice-dlci
|
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810.
|
ftc-trunk voice-dlci
To map the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810, use the ftc-trunk voice-dlci interface configuration command. To remove the FTC voice DLCI from the interface, use the no form of this command.
ftc-trunk voice-dlci dlci [remote-voice-dlci dlci]
no ftc-trunk voice-dlci dlci [remote-voice-dlci dlci]
Syntax Description
dlci
|
Specifies the Frame Relay DLCI for the IGX switch.
|
remote-voice-dlci dlci
|
(Optional) Specifies the remote voice DLCI If there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same.
|
Defaults
No FTC trunk voice DLCI is configured.
Command Mode
Interface configuration
Command History
Release
|
Modification
|
12.0(2) T
|
This command was first introduced.
|
Usage Guidelines
Do not enter the same DLCI that was assigned to the FTC management DLCI using the ftc-trunk management-dlci command.
Examples
The following example configures the FTC trunk voice DLCI:
Related Commands
Command
|
Description
|
connect
|
Configures a data connection that will travel over the FTC trunk to an IGX switch.
|
connect voice
|
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk.
|
encapsulation ftc-trunk
|
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface.
|
ftc-trunk frame-relay-dlci
|
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810.
|
ftc-trunk management-dlci
|
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810.
|
ftc-trunk management-protocol
|
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI.
|
