-
Cisco ONS SDH TL1 Command Guide, Release 9.4
-
Preface
-
Document Roadmap, Release 9.4
-
Chapter 1, ACT Commands
-
Chapter 2, APPLY Commands
-
Chapter 3, ALW Commands
-
Chapter 4, CANC Commands and Messages
-
Chapter 5, CHG Commands
-
Chapter 6, CLR Commands
-
Chapter 7, COPY Commands
-
Chapter 8, CONN Commands
-
Chapter 9, DISC Commands
-
Chapter 10, DLT Commands
-
Chapter 11, ED Commands
-
Chapter 12, ENT Commands
-
Chapter 13, EX Commands
-
Chapter 14, INH Commands
-
Chapter 15, INIT Commands
-
Chapter 16, OPR Commands
-
Chapter 17, REPT Messages
-
Chapter 18, RLS Commands
-
Chapter 19, RMV Commands
-
Chapter 20, RST Commands
-
Chapter 21, RTRV Commands
-
Chapter 22, SCHED Commands
-
Chapter 23, SET Commands
-
Chapter 24, SW Commands
-
Chapter 25, Access Identifiers
-
Chapter 26, Conditions
-
Chapter 27, Modifiers
-
Feedback
Table Of Contents
21.26 RTRV-BULKROLL-<STM_TYPE>
21.56 RTRV-FFP-<MOD2DWDMPAYLOAD>
21.118 RTRV-PROTNSW-<MOD2DWDMPAYLOAD>
21.119 RTRV-PROTNSW-<STM_TYPE>
21.130 RTRV-RMONTH-<MOD2_RMON>
RTRV Commands
This chapter provides retrieve (RTRV) commands for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.
Note
All commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.
21.1 RTRV-CPS
This command can be used to retrieve Control Plane Service parameter. The user needs to specify only the source port to identify the CPS. ALL and group AID are allowed.
Usage Guidelines
•
•
•
•
•
•
•
Category
DWDM
Security
provisioning
Input Format
RTRV-CPS:[<TID>]:<SRC>:<CTAG>::[:CKTID=<CKTID>][:];
Input Example
RTRV-CPS::PCHAN-1-1-RX:8::;
Input Parameters
<SRC>
Source AID from the "CrossConnectId1" section.
<CKTID>
Circuit identification parameter can be used to filter this command
Output Format
SID DATE TIME
M CTAG COMPLD "<SRC>:<DSTADDR>,<DST>,<WCT>,<CPSTYPE>:[CKTID=<CKTID>],VALMODE=<VALMODE>,[VALZONE=<VALZONE>],[VALMODESEC=<VALMODESEC>],[VALZONESEC=<VALZONESEC>],CPSSTATUS=<CPSSTATUS>,ACTVALZONE=<ACTVALZONE>:<PST_PSTQ>,[<SSTQ>]";
Output Example
tcc232 2011-08-05 16:37:44
M 8 COMPLD "PCHAN-1-1-RX&PCHAN-1-1-TX:10.20.30.40,PCHAN-2-2-TX&PCHAN-2-2-RX,2WAY,ADD:CKTID=twoway_add-passive,VALMODE=FULL,VALZONE=RED,CPSSTATUS=INACTIVE,ACTVALZONE=UNKNOWN:OOS-MA,"
;
Output Parameters
<SRC>
Source access identifier from the "ALL" section. Listable.
<DSTADDR>
Identifies the destination node IP address.
<DST>
Destination AID from the "ALL" section.
<WCT>
Identifies the wavelength connection type.
•
A unidirectional connection from a source to a destination port. Deafult is 1WAY
•
A bidirectional connection between the two ports.
<CPSTYPE>
Identifies the type of CPS.
•
CPS End Point are client ports
•
CPS End Point are trunk ports
•
CPS Source End Point is an ADD port
•
Not applicable
•
Not applicable
<CKTID>
(Optional) Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Does not contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.
<VALMODE>
Identifies the validation mode.
•
No Optical validation is performed.
•
The optical validation is performed as indicated in VALZONE parameter.
<VALZONE>
Identifies the validation operate zone.
•
Not evaluated
•
Margin > 3 sigma
•
1 < margin < 3 sigma
•
0 < margin < 1 sigma
•
-3 < margin < 0 sigma
•
Margin < -3 sigma
CPSSTATUS
Identifies the Control Plane Service status.
•
CPS is not active
•
CPS is active
•
CPS activation is started
•
CPS deactivation is started
•
CPS circuit failed (i.e. link down, node down)
•
CPS trail failed (i.e. PSM working or protected is down or fail)
•
temporary reboot status at CPS restart
•
Not applicable
•
CPS repair is started (i.e. node IP changed)
ACTVALZONE
Identifies the actual validation operate zone.
•
Not evaluated
•
Margin > 3 sigma
•
1 < margin < 3 sigma
•
0 < margin < 1 sigma
•
-3 < margin < 0 sigma
•
Margin < -3 sigma
<VALMODESEC>
Identifies the validation mode for secondary circuit
<VALZONESEC>
Identifies the validation operate zone for secondary circuit
21.2 RTRV-HOP-CPS
(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve HOP Control Plane Service (RTRV-HOP-CPS) command is used to retrieve the HOPs route contraint of the Control Plane Services.
Usage Guidelines
•
•
•
•
•
•
•
Category
DWDM
Security
Provisioning
Input Format
RTRV-HOP-CPS:[<TID>]:<SRC>:<CTAG>::[<CIRCUITTYPE>],[<ROUTETYPE>],[<HOPTYPE>],[<HOPNODE>],[<HOPSIDE>][::];
Input Example
> RTRV-HOP-CPS::ALL:333;
tcc232 2011-08-02 16:27:24
M 333 COMPLD
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"
"VFAC-1-5-2:10.20.30.40,,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"
;
Input Parameters
<SRC>
Source AID from the "CrossConnectId1" section.
<CIRCUITTYPE>
Identifies the target circuit. Allowed values are PRIMARY, SECONDARY.
<ROUTETYPE>
Identifies the target circuit route. Allowed values are MAINROUTE and BRIDGEROUTE.
<POSITION>
Identifies the position of the hop in the item list. Default value is 0.
•
•
•
•
•
<HOPTYPE>
Type of hop constraint. Allowed values are STRICT, LOOSE, EXCLUDE
•
The next hop of the path must be the indicated node and side
•
The path must cross the indicated node and side
•
The path must exclude the indicated node
<HOPNODE>
IP address of the target node.
<HOPSIDE>
Hop constraint target WDM side.
Output Format
SID DATE TIME
M CTAG COMPLD
"<SRC>:<DSTADDR>,<DST>,<CIRCUITTYPE>,<ROUTETYPE>,<POSITION><HOPTYPE>,<HOPNODE>,<HOPSIDE>";
Output Example
tcc232 2011-08-02 16:27:24
M 333 COMPLD
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"
"VFAC-1-5-2:10.20.30.40,,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"
;
tcc232 2011-08-02 16:27:37
M 333 COMPLD
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"
"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"
;
Output Parameters
<SRC>
Source access identifier from the "ALL" section. Listable.
<DSTADDR>
Identifies the destination node IP address.
<DST>
Destination AID from the "ALL" section.
<CIRCUITTYPE>
Identifies the target circuit. Allowed values are PRIMARY,SECONDARY.
<ROUTETYPE>
Identifies the target circuit route. Allowed values are MAINROUTE, BRIDGEROUTE.
<POSITION>
Identifies the position of the hop in the item list.
<HOPTYPE>
Type of hop constraint. Allowed values are STRICT, LOOSE, EXCLUDE.
•
The next hop of the path must be the indicated node and side.
•
The path must cross the indicated node and side.
•
The path must exclude the indicated node.
<HOPNODE>
IP address of the target node.
<HOPSIDE>
Hop constraint target WDM side.
21.3 RTRV-<MOD1FCPAYLOAD>
(Cisco ONS 15454 SDH) The Retrieve 1GFC, 2GFC, 4 GFC, 5GIB, 8GFC, or 10 GFC (RTRV-<MOD1FCPAYLOAD>) command retrieves the attributes related with the Fibre Channel port. SeeTable 27-1 for supported modifiers by platform.
Usage Guidelines
None
Category
Ports
Security
Retrieve
Input Format
RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-1GFC:CISCO:FAC-6-1:888;
Input Parameters
<AID>
Access identifier from the FACILITY.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>,
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[SQUELCHMODE=<SQUELCHMODE>]:<PSTPSTQ>,[<SST>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-1-1:,,WORK,ACT:LINKRATE=1GFC,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,
NAME=\"FC PORT\",SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,
LOSSB=LR-1:LOCKED-ENABLED,MAINTENANCE",
SQUELCHMODE=SQUELCH:OOS-MA,DSBLD"
;
Table 21-1 Output Parameter Support
<AID>
Access identifier from the "FACILITY" section.
<ROLE>
(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.
•
The entity is a protection unit in the protection group.
•
The entity is a working unit in the protection group.
<STATUS>
(Optional) The port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.
•
The entity is the active unit in the shelf.
•
Status is unavailable.
•
The entity is the standby unit in the shelf.
<LINKRATE>
(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
The rate is unknown.
•
The Small Form-factor Pluggable (SFP) is not plugged into the Fibre Channel port so the link rate cannot be detected.
<LINKSTATE>
(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.
•
Monitored parameter with values equal to or greater than the level of LEV will be reported.
•
Monitored parameter with values equal or less than the value of LEV will be reported.
<LINKRCVRY>
(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
<DISTEXTN>
(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension)
•
Buffer to buffer flow control
•
No distance extension
LINKCREDITS
(Optional) Number of link credits. LINKCREDITS is an integer.
MFS
(Optional) Maximum frame size. MFS is an integer.
ENCAP
(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.
•
Generic framing procedure (GFP) frame mode
•
GFP transparent mode
•
High-level data link control (HDLC) frame mode
•
HDLC LAN extension frame mode
•
HDLC X.86 frame mode
<NAME>
(Optional) Identifies the port name. NAME is a string.
<SOAK>
(Optional) Locked-Automatic In Service to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.
<SOAKLEFT>
(Optional) Time remaining for the transition from Locked-Automatic In Service to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. The rules for SOAKLEFT are:
•
•
•
<FREQ>
(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1528.77
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach CX1
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
10 GE extended range
•
10 GE long range
•
10 GE short range
•
Reach VX
•
Reach ZX
<SQUELCHMODE>
Shuts down the far-end laser in response to certain defects.
•
Squelch is enabled.
•
No Squelch.
•
Squelch is disabled.
<PSTPSTQ>
Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the primary state (PST) and primary state qualifier (PSTQ).
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SST>
(Optional) Secondary state of the entity. The parameter type is secondary state (SST), which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.4 RTRV-<MOD1FICONPAYLOAD>
(Cisco ONS 15454 SDH) The Retrieve 1GFICON, 2GFICON, or 4GFICON (RTRV-MOD1FICONPAYLOAD>) command returns Fibre-Channel-specific settings for ports that have been configured to carry fiber connectivity (FICON) traffic using the ENT-FICON command. The MXP_MR_2.5G and MXPP_MR_2.5G cards only support the GFP-T frame type. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
None
Category
Ports
Security
Retrieve
Input Format
RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>;
Input Example
RTRV-1GFICON:CISCO:FAC-1-1:123;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[LINKRATE=<LINKRATE>],[LINKSTATE=<LINKSTATE>],
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>],
[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,<SST>"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-1-1:,,WORK,ACT:LINKRATE=1GFICON,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,NAME=\"FC PORT\",
SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,LOSSB=LR-1:LOCKED-ENABLED,
MAINTENANCE"
;
Table 21-2 Output Parameter Support
<AID>
Access identifier from the "FACILITY" section.
<ROLE>
(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.
•
The entity is a protection unit in the protection group.
•
The entity is a working unit in the protection group.
<STATUS>
(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.
•
The entity is the active unit in the shelf.
•
Status is unavailable.
•
The entity is the standby unit in the shelf.
<LINKRATE>
(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
The rate is unknown.
•
The SFP is not plugged into the Fibre Channel port, so the link rate cannot be detected.
<LINKSTATE>
(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.
•
Monitored parameter with values equal to or greater than the level of LEV will be reported.
•
Monitored parameter with values equal or less than the value of LEV will be reported.
<LINKRCVRY>
(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
<DISTEXTN>
(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension).
•
Buffer-to-buffer flow control
•
No distance extension
<LINKCREDITS>
(Optional) Number of link credits. LINKCREDITS is an integer.
<MFS>
(Optional) Maximum frame size. MFS is an integer.
<ENCAP>
(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.
•
GFP frame mode
•
GFP transparent mode
•
HDLC frame mode
•
HDLC LAN extension frame mode
•
HDLC X.86 frame mode
<NAME>
(Optional) Identifies the port name. NAME is a string.
<SOAK>
(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.
<SOAKLEFT>
(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:
•
•
•
<FREQ>
(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1528.77
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
(Optional) The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach CX1
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
10 GE extended range
•
10 GE long range
•
10 GE short range
•
Reach VX
•
Reach ZX
<PSTPSTQ>
Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SST>
Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.5 RTRV-<MOD2DWDMPAYLOAD>
(Cisco ONS 15454 SDH) The Retrieve D1VIDEO, DV6000, DVBASI, ETRCLO, HDTV, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, PASSTHRU, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G (RTRV-<MOD2DWDMPAYLOAD>) command retrieves the configuration parameter of a dense wavelength division multiplexing (DWDM) client. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
The command supports the modifier 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G.
Category
Ports
Security
Maintenance
Input Format
RTRV-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-SDSDI::VFAC-3-2-1:321;
Input Parameters
<AID>
Access identifier from the "FACILITY" section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.
Output Format
SID DATE TIME M CTAG COMPLD "<AIDUNIONID>,<AIDTYPE>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[LBCL=<LBCL>], [OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],[SQUELCHMODE=,SQUELCHMODE.]:<PSTPSTQ>,[<SST>]" ;
Output Example
TID-000 1998-06-20 14:30:00
M 321 COMPLD
"VFAC-3-2-1,SDSDI:,,WORK,ACT:NAME=\"NY PORT\",LBCL=10.0,OPT=10.0,OPR=10.0, FREQ=1550,LOSSB=LR-1,SQUELCHMODE=SQUELCH:OOS-AU,AINS" ;
Table 21-3 Output Parameter Support
<AIDUNIONID>
Access identifier from the "AidUnionId" section.
<AIDTYPE>
A type of access identifier. The parameter type is MOD2DWDMPAYLOAD, which is the payload types applicable to DWDM ports.
•
10-Gigabit Fibre Channel payload
•
10-Gigabit Ethernet
•
40-Gigabit Ethernet
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
D1Video payload
•
DV6000 payload
•
DVBASI payload
•
ETRCLO payload
•
Gigabit Ethernet payload
•
HDTV payload
•
ISC1 payload
•
ISC3 payload
•
Any pass-through (2R) payload
<ROLE>
(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit has in the protection group.
•
The entity is a protection unit in the protection group.
•
The entity is a working unit in the protection group.
<STATUS>
(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.
•
The entity is the active unit in the shelf.
•
Status is unavailable.
•
The entity is the standby unit in the shelf.
<NAME>
(Optional) Identifies the port name. NAME is a string.
<LBCL>
(Optional) Displays the current value of the laser current. LBCL is a float.
<OPT>
(Optional) Displays the current value of the transmitted optical power. OPT is a float.
<OPR>
(Optional) Displays the current value of the received optical power. OPR is a float.
<FREQ>
(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1528.77
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
(Optional) The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach CX1
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
10 GE extended range
•
10 GE long range
•
10 GE short range
•
Reach VX
•
Reach ZX
<SQUELCHMODE>
Shuts down the far-end laser in response to certain defects.
•
Squelch is enabled.
•
No Squelch.
•
ODU AIS.
<PSTPSTQ>
Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SST>
(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.6 RTRV-<MOD_RING>
(Cisco ONS 15454 SDH) The Retrieve Multiplex Section Shared Protection Ring (RTRV-<MOD_RING>) command retrieves the multiplex section-shared protection ring (MS-SPRing) information of the network element (NE). A two-fiber or four-fiber MS-SPRing can be retrieved.
Usage Guidelines
Error conditions:
•
•
•
•
•
•
Category
MS-SPRing
Security
Retrieve
Input Format
RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];
Input Example
RTRV-MSSPR:PETALUMA:ALL:123;
Input Parameters
<AID>
(Optional) Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. Only ALL, null or a list of MSSPR-# in AID are allowed. A null value is equivalent to ALL.
Output Format
SID DATE TIME
M CTAG COMPLD
"[<AID>]::[RINGID=<RINGID>],[NODEID=<NODEID>],[MODE=<MODE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>],
[EASTWORK=<EASTWORK>],[WESTWORK=<WESTWORK>],[EASTPROT=<EASTPROT>],
[WESTPROT=<WESTPROT>]"
;Output Example
•
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"MSSPR-43::RINGID=43,NODEID=3,MODE=4F,RVRTV=Y,RVTM=5.0,
SRVRTV=Y,SRVTM=5.0,EASTWORK=FAC-5-1,WESTWORK=FAC-6-1,
EASTPROT=FAC-12-1,WESTPROT=FAC-13-1"
;•
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"MSSPR-N12EF::RINGID=N12EF,NODEID=2,MODE=2F,RVRTV=Y,RVTM=5.0,
EASTWORK=FAC-5-1,WESTWORK=FAC-6-1"
;
Table 21-4 Output Parameter Support
<AID>
(Optional) Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE.
<RINGID>
(Optional) The MS-SPRing ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.
<NODEID>
(Optional) The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31. NODEID is a string.
<MODE>
(Optional) Mode with which the command is to be implemented. Identifies the MS-SPRing mode; either two-fiber or four-fiber. The parameter type is MSSPR_MODE, which is the MS-SPRing mode.
•
Two-fiber MS-SPRing
•
Four-fiber MS-SPRing
<RVRTV>
(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).
•
Does not revert service to original line after restoration.
•
Reverts service to original line after restoration.
<RVTM>
(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<SRVRTV>
(Optional) The span revertive mode for four-fiber MS-SPRing only. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
<SRVTM>
(Optional) The span revertive time for four-fiber MS-SPRing only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<EASTWORK>
(Optional) East working facility. AID from the "FACILITY" section.
<WESTWORK>
(Optional) West working facility. AID from the "FACILITY" section.
<EASTPROT>
(Optional) East protecting facility. AID from the "FACILITY" section.
<WESTPROT>
(Optional) West protecting facility. AID from the "FACILITY" section.
21.7 RTRV-<PATH>
(Cisco ONS 15454 SDH) The Retrieve VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (RTRV-<PATH>) command retrieves the attributes associated with an VC path. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
•
•
•
•
•
–
–
•
•
Sending this command while MSSPRPTHTYPE=PCA, whether there is MS-SPRing switch or not, the protection channel access (PCA) path J1/C2 data will be returned (if there is PCA circuit on the AID). Sending this command with a VC AID without circuits and no MS-SPRing switched on the VC, will return and error message.
•
•
•
•
•
Category
Paths
Security
Retrieve
Input Format
RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[MSSPRPTHTYPE=<MSSPRPTHTYPE>][:];
Input Example
Cisco ONS 15454 SDH
RTRV-VC4:FERNDALE:VC4-2-1-4:238:::MSSPRPTHTYPE=NON-PCA;
Table 21-5 Input Parameter Support
<AID>
Access identifier from the "CrossConnectId1" section.
<MSSPRPTHTYPE>
(Optional) The MS-SPRing path type (only if the port is on the MS-SPRing). Defaults to NON-PCA. Applicable only to VC-level paths in SDH. A null value defaults to NON-PCA. The parameter type is MSSPR_PTH_TYPE, which is the MS-SPRing path type only if the port is on the MS-SPRing.
•
The AID is on the working path, or the cross-connection card protection path.
•
The AID is on the MS-SPRing PCA path.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>],[SFBER=<SFBER>],[SDBER=<SDBER>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[HOLDOFFTIMER=<HOLDOFFTIMER>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>],[INCTRC=<INCTRC>],
[TRCMODE=<TRCMODE>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SNCPPTHSTATE=<SNCPPTHSTATE>],[C2=<C2>],
[MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PSTPSTQ>,[<SSTQ>]"
;Output Example
Cisco ONS 15454 SDH
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"VC4-2-1-4::LEVEL=VC4,SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
INCTRC="INCTRCSTRING",TRCMODE=AUTO,TACC=8,TAPTYPE=DUAL,
SNCPPTHSTATE=ACT,C2=0X04,
MSSPRPTHSTATE=PROTPTHACT:UNLOCKED-DISABLED,AUTOMATICINSERVICE";
Table 21-6 Output Parameter Support
<AID>
Access identifier from the "CrossConnectId1" section.
<LEVEL>
(Optional) The rate of the cross-connected channel. Applicable only to High-Order paths (VC4). The parameter type is PATH, which is the modifier for path commands.
•
Synchronous Transport Signal/Module Level-1 (51 Mbps)
•
Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)
•
Synchronous Transport Signal/Module Level-18 Concatenated (933 Mbps)
•
Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)
•
Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)
•
Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)
•
Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)
•
Synchronous Transport Signal/Module level-6 (310 Mbps)
•
Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)
•
Virtual Tributary 2. Virtual Channel 12
•
Virtual Tributary 1. Virtual Channel 11
<SFBER>
(Optional) A VC path signal failure threshold that only applies to SNCP. Applicable only to High-Order paths. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
(Optional) A VC path signal degrade threshold that only applies to SNCP. Applicable only High-Order paths. Defaults 1E-6. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<RVRTV>
(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).
•
Does not revert service to original line after restoration.
•
Reverts service to original line after restoration.
RVTM
(Optional) Revertive time. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
•
Disable an attribute.
•
Enable an attribute.
<HOLDOFFTIMER>
(Optional) Hold off timer. HOLDOFFTIMER is an integer.
<EXPTRC>
(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR and LF. Applicable to VC-level paths (VCn). Defaults to NULL when SNCP path is created. EXPTRC is a string.
<TRC>
(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. A null value defaults to the NE transmitting null characters (Hex 00). Applicable to VC-level paths (VCn). TRC is a string.
<INCTRC>
(Optional) The incoming path trace message contents. INCTRC is any combination of 64 characters. Applicable only to VC-level paths in (VCn). Defaults to Null when a SNCP path is created. INCTRC is a string.
<TRCMODE>
(Optional) Path trace mode. Applicable only to VC-level paths (VCn). Defaults to OFF when a SNCP path is created. The parameter type is TRCMODE, which is the trace mode.
•
Use the previously received path trace string as the expected string (not applicable to MXP_2.5G_10G and TXP_MR_10G cards).
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP detected.
•
Turn off path trace capability. Nothing will be reported.
<TACC>
(Optional) Test access. Indicates whether the digroup being provisioned is to be used as a test access digroup. Defaults to N.
<TAPTYPE>
(Optional) TAP type. The parameter type is TAPTYPE, which is the test access point type.
•
Dual facility access digroup (FAD).
•
Single FAD
<SNCPPTHSTATE>
(Optional) Indicates whether a given AID is the working or standby path of a SNCP cross-connect. The parameter type is STATUS, which is the status of the unit in the protection pair.
•
The entity is the active unit in the shelf.
•
Status is unavailable.
•
The entity is the standby unit in the shelf.
<C2>
(Optional) The C2 byte hex code. Applicable only to VC-level paths (VCn). The parameter type is C2_BYTE, which is the C2 byte hex code.
•
Unequipped
•
Equipped-Non Specific payload
•
VT-Structured VC-1 synchronous payload envelope (SPE)
•
Locked Virtual Tributary (VT) mode
•
Asynchronous Mapping for DS3
•
Asynchronous Mapping for DS4 North American (NA)
•
Mapping for asynchronous transfer mode (ATM)
•
Mapping for distributed queue dual bus (DQDB)
•
Asynchronous Mapping for fiber distributed data interface (FDDI)
•
High-level data link control (HDLC)-Over-SDH Mapping
•
VT-structured VC4-1 SPE with 1VTx payload defect
•
VT-structured VC4-1 SPE with 2VTx payload defects
•
VT-structured VC4-1 SPE with 3VTx payload defects
•
VT-structured VC4-1 SPE with 4VTx payload defects
•
VT-structured VC4-1 SPE with 5VTx payload defects
•
VT-structured VC4-1 SPE with 6VTx payload defects
•
VT-structured VC4-1 SPE with 7VTx payload defects
•
VT-structured VC4-1 SPE with 8VTx payload defects
•
VT-structured VC4-1 SPE with 9VTx payload defects
•
VT-structured VC4-1 SPE with 10VTx payload defects
•
VT-structured VC4-1 SPE with 11VTx payload defects
•
VT-structured VC4-1 SPE with 12VTx payload defects
•
VT-structured VC4-1 SPE with 13VTx payload defects
•
VT-structured VC4-1 SPE with 14VTx payload defects
•
VT-structured VC4-1 SPE with 15VTx payload defects
•
VT-structured VC4-1 SPE with 16VTx payload defects
•
VT-structured VC4-1 SPE with 17VTx payload defects
•
VT-structured VC4-1 SPE with 18VTx payload defects
•
VT-structured VC4-1 SPE with 19VTx payload defects
•
VT-structured VC4-1 SPE with 20VTx payload defects
•
VT-structured VC4-1 SPE with 21VTx payload defects
•
VT-structured VC4-1 SPE with 22VTx payload defects
•
VT-structured VC4-1 SPE with 23VTx payload defects
•
VT-structured VC4-1 SPE with 24VTx payload defects
•
VT-structured VC4-1 SPE with 25VTx payload defects
•
VT-structured VC4-1 SPE with 26VTx payload defects
•
VT-structured VC4-1 SPE with 27VTx payload defects
•
VT-structured VC4-1 SPE with 28VTx payload defects
•
O.181 Test Signal (TSS1 to TSS3) Mapping
•
Reserved. C2 is 0XFF if AIS-L is being generated by an optical card or cross-connect downstream.
<MSSPRPTHSTATE>
(Optional) The MS-SPRing path state only if the port is on the MS-SPRing. Applicable only to VC-level paths in SDH (VCn). The parameter type is MSSPR_PTH_STATE, which is the MS-SPRing path state only if the port is on the MS-SPRing.
•
Indicates that the MS-SPRing switched and its PCA path is in the active state.
•
Indicates that the MS-SPRing switched and its PCA path is in the standby state.
•
Indicates that the MS-SPRing switched and its protection path is in the active state.
•
Indicates that the MS-SPRing switched and its working path is in the active state.
•
Indicates that the MS-SPRing switched and its working path is in the standby state.
<PSTPSTQ>
Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and the PSTQ.
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SSTQ>
(Optional) Secondary state of the entity. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.8 RTRV-<STM_TYPE>
(Cisco ONS 15454 SDH) The Retrieve (STM1, STM4, STM16, STM64) command retrieves the attributes (such as service parameters) and the state of an STM facility. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
•
•
Category
Ports
Security
Retrieve
Input Format
RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-STM16:PENNGROVE:FAC-6-1:236;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
Output Format
Cisco ONS 15454 SDH
SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[RSDCC=<RSDCC>],[AREA=<AREA>],
[TMGREF=<TMGREF>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],
[PJMON=<PJMON>],[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],
[WVLEN=<WVLEN>],[RINGID=<RINGID>],[MSSPRTYPE=<MSSPRTYPE>],
[MUX=<MUX>],[UNIC=<UNIC>],[CCID=<CCID>],[NBRIX=<NBRIX>],[SOAK=<SOAK>],
[SOAKLEFT=<SOAKLEFT>],[SSMRCV=<SSMRCV>],[OSPF=<OSPF>],
[MSDCC=<MSDCC>],[NAME=<NAME>],[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>], [SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>], [FOREIGNIPADDRESS=<FOREIGNIPADDRESS>],
[SQUELCHMODE=<SQUELCHMODE>], <PSTPSTQ>,[<SSTQ>]"
;Output Example
Cisco ONS 15454 SDH
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1:,,WORK,ACT:RSDCC=Y,AREA=10.92.63.1,TMGREF=N,SYNCMSG=N,SENDDUS=N,
PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,WVLEN=1310.00,RINGID=43,
MSSPRTYPE=WESTWORK,MUX=E2,UNIC=Y,CCID=8,NBRIX=2,SOAK=52,
SOAKLEFT=12-25,SSMRCV=STU_SDH,OSPF=Y,MSDCC=Y,NAME=\"STM PORT\",
LBCL=10.0,OPT=10.0,OPR=10.0, EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCFORMAT=16-BYTE,ADMSSM=G811, SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=Y,
FOREIGNIPADDRESS=10.92.63.44,UNLOCKED-DISABLED,AUTOMATICINSERVICE";
Table 21-7 Output Parameter Support
<AID>
Access identifier from the "FACILITY" section.
<ROLE>
(Optional) An STM port role. The parameter type is SIDE, which is the role the unit is playing in the protection group.
•
The entity is a protection unit in the protection group.
•
The entity is the active unit in the shelf.
•
Status is unavailable.
•
The entity is the standby unit in the shelf.
<RSDCC>
(Optional) Indicates whether or not the regenerator section DCC (RS-DCC) is to be used. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<AREA>
(Optional) Area ID. Shows up only if the DCC is enabled. AREA is a string.
<TMGREF>
(Optional) The termination to be used, whether primary or secondary. Identifies if an STM port has a timing reference. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)
•
Disable an attribute.
•
Enable an attribute.
<SYNCMSG>
(Optional) Synchronization status message. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<SENDDUS>
(Optional) The facility will send the Do Not Use for Synchronization (DUS) value in 0x0f bit pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)
•
Disable an attribute.
•
Enable an attribute.
<PJMON>
(Optional) Identifies an STM port PJMON. Defaults to 0 (zero). PJMON is an integer. Set a valid VC4 number of the optical port.
Note
<SFBER>
(Optional) An STM port signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
(Optional) An STM port signal degrade threshold. Defaults 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<MODE>
(Optional) STM port mode. Defaults to SDH. The parameter type is OPTICAL_MODE, which is the facility's optical mode.
•
The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.
•
The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.
•
The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.
<WVLEN>
(Optional) An STM port wavelength, expressed in nanometers. For example, WVLEN=1310.00 means it operates at 1310 nm in the DWDM application. WVLEN is a float.
<RINGID>
(Optional) The MS-SPRing RINGID with which the port is connected. RINGID ranges from 0 to 9999. RINGID is an integer.
<MSSPRTYPE>
(Optional) The MS-SPRing type with which the port is connected. The parameter type is MSSPR_TYPE, which is the MS-SPRing type of an STM port.
•
The STM port is an east protecting port.
•
The STM port is an east working port.
•
The STM port is an west protecting port.
•
The STM port is an west working port.
<MUX>
(Optional) MS-SPRing extension byte. The parameter type is MUX_TYPE, which is the MS-SPRing extension byte.
•
E2 byte (orderwire)
•
F1 byte (user)
•
K3 byte
•
Z2 byte
<SOAK>
(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.
<SOAKLEFT>
(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:
•
•
•
<SSMRCV>
(Optional) Displays the quality of the individual port. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.
•
Do Not Use For Synchronization
•
G811 Standard
•
Reserved For Network Synchronization Use
•
G812T Standard
•
Synchronized, Traceability Unknown
•
G812TL Standard
•
Synchronous Equipment Timing Source
<OSPF>
(Optional) The Open Shortest Path First discovery. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
<MS-DCC>
(Optional) The line DCC connection on the port. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<NAME>
(Optional) Port Name. NAME is a string.
<LBCL>
(Optional) Displays the current value of the laser current. LBCL is a float.
<OPT>
(Optional) Displays the current value of the transmitted optical power. OPT is only displayed for DWDM cards. OPT is a float.
<OPR>
(Optional) Received optical power. OPR is a float.
<EXPTRC>
(Optional) Expected path trace content. EXPTRC is a string.
<TRC>
(Optional) Path trace message to be transmitted. TRC is a string.
<TRCMODE>
(Optional) Path trace mode. Applicable only to VC-level Paths in SDH (VCn). Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•
Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>
(Optional) Trace message size. The parameter type is TRCFORMAT, which is the trace format.
•
1 byte trace message
•
16 byte trace message
•
64 byte trace message
•
Enable an attribute
<ADMSSM>
(Optional) SSM selectable value. Only displayed when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.
•
Do Not Use For Synchronization
•
G811 Standard
•
Reserved For Network Synchronization Use
•
G812T Standard
•
Synchronized, Traceability Unknown
•
G812TL Standard
•
Synchronous Equipment Timing Source
<SENDDUSFF>
(Optional) Indicates that the facility will send the DUS value in 0xff bits pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute
•
Enable an attribute
<AISONLPBK>
(Optional) The parameter type is AIS_ON_LPBK, which indicates if AIS should be sent on loopback.
•
AIS is sent on facility loopback.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopback.
•
AIS is sent on terminal loopback.
<FREQ>
(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
(Optional) The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach CX1
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
10 GE extended range
•
10 GE long range
•
10 GE short range
•
Reach VX
•
Reach ZX
<FOREIGNFEND>
(Optional) Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF (disable or enabled an attribute).
•
Disable an attribute.
•
Enable an attribute.
<FOREIGNIP>
(Optional) The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGNIP is a string.
<SQUELCHMODE>
Shuts down the far-end laser in response to certain defects.
•
Squelch is enabled.
•
No Squelch
•
Generic AIS
<PSTPSTQ>
(Optional) Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SSTQ>
(Optional) The secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.9 RTRV-10GIGE
(Cisco ONS 15454 SDH) The Retrieve 10GIGE (RTRV-10GIGE) command retrieves the 10-Gbps-specific parameters for a port that has been configured to support the Gigabit Ethernet payload with the ENT-10GIGE command.
Usage Guidelines
None
Category
Ports
Security
Retrieve
Input Format
RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-10GIGE:TID:FAC-1-1:100;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[MACADDR=<MACADDR>],
[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,[<SST>]"
;Output Examples
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1:,,WORK,ACT:NAME=\"NY PORT\",MACADDR=00-0E-AA-BB-CC-FF,LBCL=10.0,
OPT=10.0,OPR=10.0,FREQ=1550,LOSSB=SX:Unlocked-Disabled,AutomaticInService"
;
Table 21-8 Output Parameter Support
<AID>
Access identifier from the "FACILITY" section.
<ROLE>
(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.
•
The entity is the standby unit in the shelf.
<NAME>
(Optional) Port name. NAME is a string.
<MACADDR>
(Optional) The MAC address for the 10 Gigabit Ethernet payload. MACADDR is a string.
<LBCL>
(Optional) Displays the current value of the laser current. LBCL is a float.
<OPT>
(Optional) Displays the current value of the transmitted optical power. OPT is a float.
<OPR>
(Optional) Displays the current value of the received optical power. OPR is a float.
<FREQ>
(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1528.77
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
(Optional) The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach CX1
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
10 GE extended range
•
10 GE long range
•
10 GE short range
•
Reach VX
•
Reach ZX
<PSTPSTQ>
Administrative state in the PSTPSTQ format. The parameter type is PSTPSTQ, which is the service state of the entity described by the PST and the PSTQ.
•
In service and normal
•
Out of service and autonomous
•
Out of service, autonomous and management
•
Out of service and management
<SST>
(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
21.10 RTRV-ALM-<MOD2ALM>
(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve Alarm for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, CHGRP, DS1, DS3I, DVBASI, E1, E100, E1000, E3, E4, EC1, ETH, FSTE, G1000, GFPOS, GIGE, HDLC, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, MSISC, OCH, OMS, OTS, OTU2, OTU3, POS, RPRIF, STM1E, VC3, VC4-4C, VC4-6C, VC4-8C, VC4-12C, VC4, VC4-16C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-16c, VC4-64c, VCG, VC11, VC12, WLEN, 3GVIDEO, HDSDI, ISC3STP1G, ISC3STP2G, OTU1, or SDSDI (RTRV-ALRM-<MOD2ALM>) command retrieves and sends the current status of alarm conditions. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
The command supports the modifier 3GVIDEO, OTU1, SDSDI, HDSDI, ISC3STP1G, and ISC3STP2G.
•
•
Category
Fault
Security
Retrieve
Input Format
RTRV-ALM-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],[<LOCN>],[<DIRN>][,];
Input Example
RTRV-ALM-OTU1::VFAC-5-3-1:1::MN,,NSA,NEND,RCV;
Table 21-9 Input Parameter Support
<AID>
Access identifier from the "AidUnionId" section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.
<NTFCNCDE>
(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
(Optional) Condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 for a list of conditions.
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"
;
Output Example
tcc2 2011-08-18 16:16:18
M 1 COMPLD
"VFAC-5-3-1,OTU1:MN,HI-RXPOWER,NSA,08-18,12-56-40,NEND,RCV:\"Facility High Rx power\","
;
Table 21-10 Output Parameter Support
<AID>
Access identifier from the "ALL" section.
<AIDTYPE>
(Optional) Type of access identifier. The parameter type is MOD2ALM, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
1-Gigabit ISC3 compatible
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Fibre Channel payload
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
Client facility for MXP/TXP cards
•
Channel group
•
DS3i-N-12 facility
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
E1 facility
•
E100 facility
•
E1000 facility
•
E3 facility
•
E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.
•
Fast Ethernet port facility
•
G1000 facility
•
Generic framing protocol over packet over SDH virtual port facility
•
Gigabit Ethernet port facility
•
1.5G HD-SDI video payload.
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
(ONS 15454) ML-Series two port Gigabit Ethernet card
•
MSISC
•
Optical channel
•
OCH termination
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port facility
•
270M SDI video payload.
•
STM1 facility
•
STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.
•
STM4 facility
•
STM16 facility
•
STM64 facility
•
VC11 path
•
VC12 path
•
VC3 path
•
VC38C path
•
VC44C path
•
VC464C path
•
VC48C path
•
VC4 path
•
VC416C path
•
VC42C path
•
VC43C path
•
T3 path
•
UDCDCC path
•
UCDF path
•
Virtual concatenation group alarm
•
Wavelength path provisioning
<NTFCNCDE>
Two-letter notification code. the parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See the Table 26-1 for a list of conditions.
<SRVEFF>
The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
<DESC>
(Optional) The condition description.
21.11 RTRV-ALMTYPE
(Cisco ONS 15454 SDH) The Retrieve Alarm Type command retrieves all system and user-defined alarm types.
Usage Guidelines
None
Category
System
Security
Retrieve
Input Format
RTRV-ALMTYPE:[<TID>]::<CTAG>;
Input Example
RTRV-ALMTYPE:CISCONODE::1;
Input Parameters
None.
Output Format
SID DATE TIME
M CTAG COMPLD
"<TYPEOFALM>,<ALMTYPE>"
;Output Examples
CISCONODE 2007-06-26 14:30:00
M 1 COMPLD
"SYSTEMDEFINED,AIRCOMPR"
;
21.12 RTRV-ALM-ALL
(Cisco ONS 15454 SDH) The Retrieve Alarm All (RTRV-ALM-ALL) command retrieves and sends the current status of all active alarm conditions. The alarm condition or severity to be retrieved is specified using the input parameters as a filter. To retrieve all the NE alarms, issue all of the following commands:
RTRV-ALM-ALL
RTRV-ALM-BITS
RTRV-ALM-ENV
RTRV-ALM-SYNCNUsage Guidelines
None
Category
Fault
Security
Retrieve
Input Format
RTRV-ALM-ALL:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],
[<CONDITION>],[<SRVEFF>],[<LOCN>],[<DIRN>],[,];Input Example
RTRV-ALM-ALL:COTATI:ALL:229::MN,PWRRESTART,NSA,NEND,RCV;
Table 21-12 Input Parameter Support
<AID>
Access identifier from the "ALL" section. A null value is equivalent to ALL. AID is a string.
<NTFCNCDE>
(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
<CONDITION>
(Optional) The type of alarm condition. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<LOCN>],[<DIRN>]:
[<DESC>],[<AIDDET>]";
Output Examples
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SLOT-2,EQPT:MN,PWRRESTART,NSA,08-01,14-25-59,NEND,RCV:\"POWER FAIL RESTART\", DS1-14"
;
Table 21-13 Output Parameter Support
<AID>
(Optional) Access identifier from the "ALL" section.
<AIDTYPE>
(Optional) Type of facility, link, or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
Building integrated timing supply (BITS) alarm
•
Channel group
•
Client facility for MXP/TXP cards
•
Common alarm
•
DS3i-N-12 facility
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
E1 facility
•
E3 facility
•
E100 facility
•
ETH facility
•
E1000 facility
•
E4 facility
•
ENV facility
•
EQPT facility
•
Fast Ethernet port facility
•
G1000 facility
•
Gigabit Ethernet port facility
•
High-level data link control (HDLC) frame mode.
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload
•
ISC-3 STP 2G video payload
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
(ONS 15454) ML-Series two port Gigabit Ethernet card
•
ML-Series 100T eight port Gigabit Ethernet card
•
MSISC
•
Optical channel
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port facility
•
Resilient Ethernet Protocol
•
STM1 facility
•
STM1E facility
•
STM4 facility
•
STM16 facility
•
STM64 facility
•
SYNCN facility
•
TCC facility
•
VC11 path
•
VC12 path
•
VC3 path
•
VC44C path
•
VC38C path
•
VC464C path
•
VC48C path
•
VC4 path
•
VC416C path
•
VC42C path
•
VC43C path
•
T3 path
•
UDCDCC path
•
UCDF path
•
Virtual concatenation group alarm
•
Wavelength path provisioning
<NTFCNCDE>
Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
<OCRDAT>
Date when the specific event or violation occurred, MM-DD.
<OCRTM>
Time when the specific event or violation occurred, HH-MM-SS.
<DESC>
(Optional) A condition description. DESC is a string.
<AIDDET>
(Optional) The supplementary equipment identification. AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed.
21.13 RTRV-ALM-BITS
(Cisco ONS 15454 SDH) The Retrieve Alarm Building Integrated Timing Supply (RTRV-ALM-BITS) command retrieves and sends the current status of alarm conditions associated with the BITS facility. The alarm condition or severity retrieved is specified using the input parameters as a filter.
Usage Guidelines
None
Category
Synchronization
Security
Retrieve
Input Format
RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];Input Example
Cisco ONS 15454 SDH
RTRV-ALM-BITS:ELVERANO:BITS-1:228::CR,LOS,SA;
Table 21-14 Input Parameter Support
<AID>
Access identifier from the "BITS" section.
<NTFCNCDE>
(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed
•
The alarm is not reported
<CONDTYPE>
(Optional) The condition type for an alarm or reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an Cisco ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCATION>],[<DIRECTION>]:[<DESC>],";
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BITS-1,BITS:CR,LOS,SA,08-01,14-25-59,,:\"LOSS OF SIGNAL\","
;
Table 21-15 Output Parameter Support
<AID>
Access identifier from the "BITS" section.
<AIDTYPE>
(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
BITS alarm
•
Channel group
•
Client facility for MXP/TXP cards
•
Common alarm
•
DS3i-N-12 facility
•
E1 facility
•
E3 facility
•
E100 facility
•
E1000 facility
•
E4 facility
•
ENV facility
•
EQPT facility
•
Fast Ethernet port facility
•
G1000 facility
•
Gigabit Ethernet port facility
•
High-level data link control (HDLC) frame mode.
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
Optical channel
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port facility
•
Resilient Ethernet Protocol
•
STM1 facility
•
STM1E facility
•
STM4 facility
•
STM16 facility
•
STM64 facility
•
SYNCN facility
•
TCC facility
•
VC11 path
•
VC12 path
•
VC3 path
•
VC44C path
•
VC38C path
•
VC464C path
•
VC48C path
•
VC4 path
•
VC416C path
•
VC42C path
•
VC43C path
<NTFCNCDE>
Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<LOCATION>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRECTION>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
<DESC>
(Optional) A condition description. DESC is a string.
21.14 RTRV-ALM-ENV
(Cisco ONS 15454 SDH) The Retrieve Alarm Environment (RTRV-ALM-ENV) command retrieves the environmental alarms.
Usage Guidelines
None
Category
Environment
Security
Retrieve
Input Format
RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];
Input Example
RTRV-ALM-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]";
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-IN-1:MJ,OPENDR,08-01,14-25-59,\"OPEN DOOR\""
;
Table 21-16 Output Parameter Support
<AID>
Access identifier from the "ENV" section.
<NTFCNCDE>
Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<ALMTYPE>
The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.
•
Air compressor failure
•
Air conditioning failure
•
Air dryer failure
•
Battery discharging
•
Battery failure
•
Cooling fan failure
•
Centralized power major failure
•
Centralized power minor failure
•
Engine failure
•
Engine operating
•
Standby engine transfer
•
Explosive gas
•
Fire detector failure
•
Fire
•
Flood
•
Fuel leak
•
Fuse failure
•
Explosive gas, toxic gas, ventilation fail or gas monitor fail
•
CEV hatch fail
•
Generator failure
•
High air flow
•
High humidity
•
High temperature
•
High water
•
Intrusion
•
Level converter
•
Secondary ADSL low voltage disconnect
•
Low voltage disconnect bypass
•
Low battery voltage
•
Low fuel
•
Low humidity
•
Low cable pressure
•
Low temperature
•
Low water
•
Miscellaneous
•
Open door
•
Commercial power failure
•
Pump failure
•
48 V power supply failure
•
-139 V power converter
•
-190 V power converter
•
Power supply major
•
Power supply minor
•
Rectifier failure
•
Rectifier high voltage
•
Rectifier low voltage
•
Ringing generator major
•
Ringing generator minor
•
AC or AC/rectifier power fail ADSL equipment
•
AC or AC/rectifier power fail DCL equipment critical site
•
AC or AC/rectifier power fail DCL equipment
•
Commercial AC fail, site equipped with standby engine
•
AC power loss distributed power RT bay
•
Retrieve standby engine, commercial AC restored
•
Smoke
•
High-low temperature
•
Toxic gas
•
T-repeater shelf
•
Ventilation system failure
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<DESC>
(Optional) A condition description. DESC is a string.
21.15 RTRV-ALM-EQPT
(Cisco ONS 15454 SDH) The Retrieve Alarm Equipment (RTRV-ALM-EQPT) command retrieves and sends the current status of alarm conditions associated with the equipment units. The alarm condition or severity to be retrieved is specified using the input parameters as a filter.
Usage Guidelines
None
Category
Equipment
Security
Retrieve
Input Format
RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];Input Example
RTRV-ALM-EQPT:TWOROCK:SLOT-1:227::MJ,HITEMP,NSA;
Table 21-17 Input Parameter Support
<AID>
Access identifier from the "EQPT" section.
<NTFCNCDE>
(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]";
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SLOT-3,EQPT:MJ,HITEMP,NSA,08-01,14-25-59,,:\"HI TEMPERATURE\","
;
Table 21-18 Output Parameter Support
<AID>
(Optional) Access identifier from the "EQPT" section.
<AIDTYPE>
(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
BITS alarm
•
Channel group
•
Client facility for MXP/TXP cards
•
Common alarm
•
DS3i-N-12 alarm
•
E1 alarm
•
(ONS 15310 MA SDH) E3 alarm
•
E100 alarm
•
E1000 alarm
•
E3 alarm
•
E4 alarm
•
ENV alarm
•
EQPT alarm
•
Fast Ethernet port alarm
•
G1000 alarm
•
Gigabit Ethernet port alarm
•
High-level data link control (HDLC) frame mode.
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
MSISC
•
Optical channel
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port alarm
•
Resilient Ethernet Protocol
•
STM1 alarm
•
STM1E alarm
•
STM4 alarm
•
STM16 alarm
•
STM64 alarm
•
SYNCN alarm
•
TCC alarm
•
VC11 alarm
•
VC12 alarm
•
VC3 alarm
•
VC44C alarm
•
VC38C alarm
•
VC464C alarm
•
VC48C alarm
•
VC4 alarm
•
VC416C alarm
•
VC42C alarm
•
VC43C alarm
<NTFCNCDE>
Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
<DESC>
(Optional) A condition description. DESC is a string.
21.16 RTRV-ALM-SYNCN
(Cisco ONS 15454 SDH) The Retrieve Alarm Synchronization (RTRV-ALM-SYNCN) command retrieves and sends the current status of alarm conditions associated with a synchronization facility. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter.
Usage Guidelines
None
Category
Synchronization
Security
Retrieve
Input Format
RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>],[<LOCN>],[<DIRN>];Input Example
RTRV-ALM-SYNCN:FULTON:SYNC-NE:226::CR,FAILTOSW,SA;
Table 21-19 Input Parameter Support
<AID>
Access identifier from the "SYNC_REF" section.
<NTFCNCDE>
(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.
•
The condition is non-service affecting.
•
The condition is service affecting.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]";
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SYNC-NE,SYNCN:CR,FAILTOSW,SA,
08-01,14-25-59,,:\"FAILURE TO SWITCH TO PROTECTION\","
;
Table 21-20 Output Parameter Support
<AID>
Access identifier from the "SYN" section.
<AIDTYPE>
(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gbps fiber connection
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
BITS alarm
•
Channel group
•
Client facility for MXP/TXP cards
•
Common alarm
•
DS3i-N-12 alarm
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
E1 alarm
•
E100 alarm
•
E1000 alarm
•
E3 alarm
•
E4 alarm
•
ENV alarm
•
EQPT alarm
•
Fast Ethernet port alarm
•
G1000 alarm
•
Gigabit Ethernet port alarm
•
High-level data link control (HDLC) frame mode.
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
MSISC
•
Optical channel
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port alarm
•
Resilient Ethernet Protocol
•
STM1 alarm
•
STM1E alarm
•
STM4 alarm
•
STM16 alarm
•
STM64 alarm
•
SYNCN alarm
•
TCC alarm
•
VC11 alarm
•
VC12 alarm
•
VC3 alarm
•
VC44C alarm
•
VC38C alarm
•
VC464C alarm
•
VC48C alarm
•
VC4 alarm
•
VC416C alarm
•
VC42C alarm
•
VC43C alarm
<NTFCNCDE>
Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
<DESC>
(Optional) A condition description. DESC is a string.
21.17 RTRV-ALMTH-<MOD2>
(Cisco ONS 15454 SDH) The Retrieve Alarm Threshold for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, D1VIDEO, DS1, DS3I, DV6000, DVBASI, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OTU3, STM1, STM4, STM16, STM64, GIGE, POS, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c, VC4-64c, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (RTRV-ALMTH-<MOD2>) command retrieves the alarm threshold values. The only applicable MOD2 values are OC3, OC12, OC48, OC192, OCH, OMS, and OTS.
Usage Guidelines
The command supports 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G modifiers.
Category
Fault
Security
Retrieve
Input Format
RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<ALMTHR>[,,::];
Input Example
RTRV-ALMTH-OTU1::VFAC-5-3-1:A::OPT-LOW;
Table 21-21 Input Parameter Support
<AID>
Access identifier from the "ALL" section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.
<ALMTHR>
Alarm threshold. Must not be null. The parameter type is ALM_THR, which is the alarm threshold list for MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, MD-4-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
•
ADD Power - High Degrade
•
ADD Power - High Failure
•
ADD Power - Low Degrade
•
ADD Power - Low Failure
•
Battery Voltage—Extremely High
•
Battery Voltage—Extremely Low
•
Battery Voltage—High
•
Battery Voltage—Low
•
Gain not reached—High Degrade Threshold
•
Gain not reached—High Failure Threshold
•
Gain not reached—Low Degrade Threshold
•
Gain not reached—Low Failure Threshold
•
Laser Bias Current in microA as a tenth of a percentage of the High Warning Threshold, Low Warning Threshold. Measured value 0.0%, 100.0%.
•
Receive power in 1tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Optical Power—High Degrade Threshold
•
Optical Power—High Failure Threshold
•
Optical Power—Low Degrade Threshold
•
Optical Power—Low Failure Threshold
•
VOA Attenuation—High Degrade Threshold
•
VOA Attenuation—High Failure Threshold
•
VOA Attenuation—Low Degrade Threshold
•
VOA Attenuation—Low Failure Threshold
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>";
Output Example
TCC2 2011-08-18 16:01:38
M A COMPLD
"VFAC-5-3-1,OTU1:OPT-LOW,,,-4.5,"
;
Table 21-22 Output Parameter Support
<AID>
Access identifier from the "ALL" section.
<MOD>
AID type. The parameter type is MOD2, which is the line/path modifier.
•
10-Gigabit Fibre Channel payload
•
10-Gigabit fiber connectivity payload
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
1-Gigabit ISC3 compatible
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
2-Gigabit ISC3 compatible
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
D1 video
•
DS1 line of a DS3XM card
•
DS3I line
•
DV6000
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
EC1 facility
•
ESCON
•
ETR_CLO
•
FSTE facility
•
G1000 facility
•
GFP over POS. Virtual ports partitioned using GFP's multiplexing capability.
•
Gigabit Ethernet
•
1.5G HD-SDI video payload.
•
HDTV
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
OC-3 facility
•
OC-12 facility
•
OC-48 facility
•
OC-192 facility
•
OC-768 facility
•
Optical Channel
•
OCH client connection
•
OCH network connection
•
OCH termination
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port
•
270M SDI video payload
•
STS1 path
•
STS3c path
•
STS6c path
•
STS9c path
•
STS18c path
•
STS12c path
•
STS24c path
•
STS36c path
•
STS48c path
•
STS192c path
•
T1/DS1 facility/line
•
T1/DS1 facility/line
•
VT1 path
•
VT2 path
<CONDTYPE>
Condition type for an alarm or a reported event. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
•
Battery Voltage—Extremely High
•
Battery Voltage—Extremely Low
•
Battery Voltage—High
•
Battery Voltage—Low
•
Gain not reached—High Degrade Threshold
•
Gain not reached—High Failure Threshold
•
Gain not reached—Low Degrade Threshold
•
Gain not reached—Low Failure Threshold
•
Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold Measured value [0.0%, 100.0%]
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Optical Power—High Degrade Threshold
•
Optical Power—High Failure Threshold
•
Optical Power—Low Degrade Threshold
•
Optical Power—Low Failure Threshold
•
VOA Attenuation—High Degrade Threshold
•
VOA Attenuation—High Failure Threshold
•
VOA Attenuation—Low Degrade Threshold
•
VOA Attenuation—Low Failure Threshold
<THLEVEL>
Threshold level. THLEVEL is a float.
21.18 RTRV-ALMTH-EQPT
(Cisco ONS 15454 SDH) The Retrieve Alarm Threshold Equipment (RTRV-ALMTH-EQPT) command retrieves the alarm thresholds for the power level monitoring on an NE.
Usage Guidelines
None
Category
Equipment
Security
Retrieve
Input Format
RTRV-ALMTH-EQPT:[<TID>]:[<AID]>:<CTAG>::[<CONDTYPE>][,,::];
Input Examples
RTRV-ALMTH-EQPT:::1::BATV-HIGH;
RTRV-ALMTH-EQPT::SHELF-2:1::BATV-HIGH;
Table 21-23 Input Parameter Support
<AID>
(Optional) The node or shelf access identifier from the "SHELF" section. If omitted, it addresses the node or first shelf of the node.
<CONDTYPE>
Alarm threshold. A null value is equivalent to ALL. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
•
Battery Voltage—Extremely High
•
Battery Voltage—Extremely Low
•
Battery Voltage—High
•
Battery Voltage—Low
•
Gain not reached—High Degrade Threshold
•
Gain not reached—High Failure Threshold
•
Gain not reached—Low Degrade Threshold
•
Gain not reached—Low Failure Threshold
•
Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%]
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Optical Power—High Degrade Threshold
•
Optical Power—High Failure Threshold
•
Optical Power—Low Degrade Threshold
•
Optical Power—Low Failure Threshold
•
VOA Attenuation—High Degrade Threshold
•
VOA Attenuation—High Failure Threshold
•
VOA Attenuation—Low Degrade Threshold
•
VOA Attenuation—Low Failure Threshold
Output Format
SID DATE TIME
M CTAG COMPLD
"[<AID>],<MOD2B>:<CONDTYPE>,,,<DNFIELD>";
Output Examples
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SHELF-1,EQPT:BATV-HIGH,,,-52.0,"
;TID-000 1998-06-20 14:30:00
M 001 COMPLD
",EQPT:BATV-HIGH,,,-52.0,""
;
Table 21-24 Output Parameter Support
<AID>
(Optional) The node or shelf access identifier from the "SHELF" section. If omitted, it addresses the node or first shelf of the node.
<MOD2B>
Alarm type. The parameter type is MOD2B, which is the alarm type.
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
BITS alarm
•
Client facility for MXP/TXP cards
•
Common alarm
•
DS3i-N-12 alarm
•
E1 alarm
•
E100 alarm
•
E1000 alarm
•
E3 alarm
•
E4 alarm
•
ENV alarm
•
EQPT alarm
•
Fast Ethernet Port alarm
•
G1000 alarm
•
Gigabit Ethernet port alarm
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
Optical channel
•
Optical Multiplex Section
•
Optical Transport Section
•
POS port alarm
•
STM1 alarm
•
STM1E alarm
•
STM4 alarm
•
STM16 alarm
•
STM64 alarm
•
SYNCN alarm
•
TCC alarm
•
VC11 alarm
•
VC12 alarm
•
VC3 alarm
•
VC44C alarm
•
VC38C alarm
•
VC464C alarm
•
VC48C alarm
•
VC4 alarm
•
VC416C alarm
•
VC42C alarm
•
VC43C alarm
<CONDTYPE>
Alarm threshold. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
•
Battery Voltage—Extremely High
•
Battery Voltage—Extremely Low
•
Battery Voltage—High
•
Battery Voltage—Low
•
Gain not reached—High Degrade Threshold
•
Gain not reached—High Failure Threshold
•
Gain not reached—Low Degrade Threshold
•
Gain not reached—Low Failure Threshold
•
Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%].
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.
•
Optical Power—High Degrade Threshold
•
Optical Power—High Failure Threshold
•
Optical Power—Low Degrade Threshold
•
Optical Power—Low Failure Threshold
•
VOA Attenuation—High Degrade Threshold
•
VOA Attenuation—High Failure Threshold
•
VOA Attenuation—Low Degrade Threshold
•
VOA Attenuation—Low Failure Threshold
<DNFIELD>
DNFIELD is a float.
21.19 RTRV-ALS
(Cisco ONS 15454 SDH) The Retrieve Automatic Laser Shutoff (RTRV-ALS) command retrieves the ALS attributes of an STM facility and all the facilities that support the ALS feature. This command is used to retrieve the ALS parameter of the STM4, STM16, and STM64 ports on the MXP_2.5G_10E, TXP_MR_10E, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_2.5G_10G, and TXP_MR_10G cards.
Usage Guidelines
None
Category
Ports
Security
Retrieve
Input Format
RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-ALS:PENNGROVE:FAC-1-1:1;
Input Parameters
<AID>
Access identifier from the "AidUnionId" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>],[LSRSTAT=<LSRSTAT>],[OSRI=<OSRI>]";
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1,STM64::ALSMODE=DISABLED,ALSRCINT=100,ALSRCPW=2.0,LSRSTAT=UP:"
;
Table 21-25 Input Parameter Support
<AID>
Access identifier from the "AidUnionId" section.
<AIDTYPE>
Type of access identifier. The parameter type is MOD2, which is the line/path modifier.
•
10-Gigabit Fibre Channel payload
•
10-Gigabit fiber connectivity payload
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
1-Gigabit ISC3 compatible
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
2-Gigabit ISC3 compatible
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
D1 video
•
DS3i-N-12 line
•
DV6000
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
E1
•
E3
•
E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.
•
ESCON
•
ETRCLO
•
FSTE facility
•
G1000 facility
•
Generic Framing Protocol over Packet Over SDH. Virtual ports partitioned using GFP's multiplexing capability.
•
Gigabit Ethernet
•
HDTV
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gigabit ISC3 Peer
•
2-Gigabit ISC3 Peer
•
1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gigabit ISC1, ISC2, and ISC3 compatibility
•
Optical Channel
•
OCH client connection
•
OCH network connection
•
OCH termination
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
POS port
•
STM1 facility
•
STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card
•
STM4 facility
•
STM16 facility
•
STM64 facility
•
VC3 path
•
VC4-4C path
•
VC3-8C path
•
VC4-64C path
•
VC4-8C path
•
VC4 path
•
VC4-16C path
•
VC4-2C path
•
VC4-3C path
•
VC11 path
•
VC12 path
<ALSMODE>
(Optional) ALS is enabled or disabled. The parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.
•
Automatic
•
Disabled
•
Manual
•
Manual restart for test
<ALSRCINT>
(Optional) ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.
<ALSRCPW>
(Optional) ALS recovery pulse width. The range is 2.0 to 100.00 seconds, in increments of 100 ms. ALSRCPW is a float.
<LSRSTAT>
(Optional) Status of the laser. The parameter type is LASER_STATUS, which is the status of laser.
•
Laser is switched on but is working automatic power reduction.
•
Laser is switched off.
•
Laser is switched on.
<OSRI>
(Optional) OSRI enabled or disabled. Present only on a port where the safety is supported. Defaults to off. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
21.20 RTRV-APC
(Cisco ONS 15454 SDH) The Operate Amplifier Power Control (RTRV-APC) command retrieves the APC application attributes.
Usage Guidelines
None
Category
DWDM
Security
Maintenance
Input Format
RTRV-APC:[<TID>]::<CTAG>;
Input Example
RTRV-APC:PENNGROVE:WDMSIDE-A:114;
Input Parameters
None
Output Format
SID DATE TIME
M CTAG COMPLD
":[ROLE=<ROLE>],[APCENABLE=<APCENABLE>],[APCSTATE=<APCSTATE>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"::APCENABLE=Y,APCSTATE=WORKING"
;
21.21 RTRV-ATTR-CONT
(Cisco ONS 15454 SDH) The Retrieve Attribute Control (RTRV-ATTR-CONT) command retrieves and sends the attributes associated with an external control. These attributes are used when an external control is operated or released. To set these attributes, use the SET-ATTR-CONT command.
Usage Guidelines
None
Category
Environment
Security
Retrieve
Input Format
RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];
Input Example
RTRV-ATTR-CONT:CISCO:ENV-OUT-2:123::AIRCOND;
Table 21-27 Input Parameter Support
<AID>
Access identifier from the "ENV" section. Identifies the external control for which attributes are being set.
<CONTTYPE>
(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.
•
Air conditioning
•
Engine
•
Fan
•
Generator
•
Heat
•
Light
•
Miscellaneous
•
Sprinkler
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-OUT-2:AIRCOND"
;
Table 21-28 Output Parameter Support
<AID>
Access identifier from the "ENV" section. Identifies the external control for which attributes are being set.
<CONTTYPE>
(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.
•
Air conditioning
•
Engine
•
Fan
•
Generator
•
Heat
•
Light
•
Miscellaneous
•
Sprinkler
21.22 RTRV-ATTR-ENV
(Cisco ONS 15454 SDH) The Retrieve Attribute Environment (RTRV-ATTR-ENV) command retrieves the attributes associated with an environmental alarm.
Usage Guidelines
None
Category
Environment
Security
Retrieve
Input Format
RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];
Input Example
RTRV-ATTR-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;
Table 21-29 Input Parameter Support
<AID>
Access identifier from the "ENV" section.
<NTFCNCDE>
(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<ALMTYPE>
(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.
•
Air compressor failure
•
Air conditioning failure
•
Air dryer failure
•
Battery discharging
•
Battery failure
•
Cooling fan failure
•
Centralized power major failure
•
Centralized power minor failure
•
Engine failure
•
Engine operating
•
Standby engine transfer
•
Explosive gas
•
Fire detector failure
•
Fire
•
Flood
•
Fuel leak
•
Fuse failure
•
Explosive gas, toxic gas, ventilation fail or gas monitor fail
•
CEV hatch fail
•
Generator failure
•
High air flow
•
High humidity
•
High temperature
•
High water
•
Intrusion
•
Level converter
•
Secondary ADSL low voltage disconnect
•
Low voltage disconnect bypass
•
Low battery voltage
•
Low fuel
•
Low humidity
•
Low cable pressure
•
Low temperature
•
Low water
•
Miscellaneous
•
Open door
•
Commercial power failure
•
Pump failure
•
48 V power supply failure
•
-139 V power converter
•
-190 V power converter
•
Power supply major
•
Power supply minor
•
Rectifier failure
•
Rectifier high voltage
•
Rectifier low voltage
•
Ringing generator major
•
Ringing generator minor
•
AC or AC/rectifier power fail ADSL equipment
•
AC or AC/rectifier power fail DCL equipment critical site
•
AC or AC/rectifier power fail DCL equipment
•
Commercial AC fail, site equipped with standby engine
•
AC power loss distributed power RT bay
•
Retrieve standby engine, commercial AC restored
•
Smoke
•
High-low temperature
•
Toxic gas
•
T-repeater shelf
•
Ventilation system failure
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-IN-1:MJ,OPENDR,\"OPEN DOOR\""
;
Table 21-30 Output Parameter Support
<AID>
Access identifier from the "ENV" section.
<NTFCNCDE>
(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<ALMTYPE>
(Optional) The alarm type for the environmental alarm. The parameter type is ENV_ALM, which is the environmental alarm type.
•
Air compressor failure
•
Air conditioning failure
•
Air dryer failure
•
Battery discharging
•
Battery failure
•
Cooling fan failure
•
Centralized power major failure
•
Centralized power minor failure
•
Engine failure
•
Engine operating
•
Standby engine transfer
•
Explosive gas
•
Fire detector failure
•
Fire
•
Flood
•
Fuel leak
•
Fuse failure
•
Explosive gas, toxic gas, ventilation fail or gas monitor fail
•
CEV hatch fail
•
Generator failure
•
High air flow
•
High humidity
•
High temperature
•
High water
•
Intrusion
•
Level converter
•
Secondary ADSL low voltage disconnect
•
Low voltage disconnect bypass
•
Low battery voltage
•
Low fuel
•
Low humidity
•
Low cable pressure
•
Low temperature
•
Low water
•
Miscellaneous
•
Open door
•
Commercial power failure
•
Pump failure
•
48 V power supply failure
•
-139 V power converter
•
-190 V power converter
•
Power supply major
•
Power supply minor
•
Rectifier failure
•
Rectifier high voltage
•
Rectifier low voltage
•
Ringing generator major
•
Ringing generator minor
•
AC or AC/rectifier power fail ADSL equipment
•
AC or AC/rectifier power fail DCL equipment critical site
•
AC or AC/rectifier power fail DCL equipment
•
Commercial AC fail, site equipped with standby engine
•
AC power loss distributed power RT bay
•
Retrieve standby engine, commercial AC restored
•
Smoke
•
High-low temperature
•
Toxic gas
•
T-repeater shelf
•
Ventilation system failure
<DESC>
(Optional) Alarm description. DESC is a string.
21.23 RTRV-AUDIT-LOG
(Cisco ONS 15454 SDH) The Retrieve Audit Log (RTRV-AUDIT-LOG) command retrieves the contents of the audit log stored in the NE. Audit records contain information for user operations such as login, logout, change of provisioning parameters and other changes a user might make when connected to the NE. Audit records do not store operations related to parameter retrieval.
Usage Guidelines
None
Category
Log
Security
Superuser
Input Format
RTRV-AUDIT-LOG:[<TID>]::<CTAG>;
Input Example
RTRV-AUDIT-LOG:::1;
Input Parameters
None
Output Format
SID DATE TIME
M CTAG COMPLD
" <ENTRYNUM>,<OCRDAT>,<OCRTM>,<TASKID>,<TXSTATUS>,<DESCRIPTION>"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"17172,2004-10-05,09-52-44, TPROVMGR,COMPLD,\"DESCRIPTION\""
;
21.24 RTRV-AUTO
(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve Auto (RTRV-AUTO) command retrieves the AUTO ports provisioned. Port bandwidth changes to OC3/OC12/OC48 as per the incoming signal when auto sense is enabled. Default being OC48 when auto sense is disabled.
Usage Guidelines
None
Category
DWDM
Security
Provisioning
Input Format
RTRV-AUTO:[<TID>]:<AID>:<CTAG>;
Input Example
RTRV-AUTO:CISCO:VFAC-2-1-1:1;
Input Parameters
None that require description
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,[DETECTEDPAYLOAD=<DETECTEDPAYLOAD>],[AUTOSENSE=<AUTOSENSE>]"
;
Output Example
M 1 COMPLD
"VFAC-15-1-1,DETECTEDPAYLOAD=OC48,AUTOSENSE=N"
;
Output Parameters
21.25 RTRV-BITS
(Cisco ONS 15454 SDH) The Retrieve Building Integrated Timing Supply (RTRV-BITS) command retrieves the BITS configuration command.
Usage Guidelines
None
Category
Synchronization
Security
Retrieve
Input Format
RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-BITS:SONOMA:BITS-1:782;
Input Parameters
<AID>
Access identifier from the "BITS" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[IMPEDANCE=<IMPEDANCE>],[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>]:[<PST>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BITS-1::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,AISTHRSHLD=G811,
SABIT=BYTE-4,IMPEDANCE=120-OHM,BITSFAC=E1,ADMSSM=G811:UNLOCKED"
;
Table 21-32 Input Parameter Support
<AID>
Access identifier from the "BITS" section.
<LINECDE>
(Optional) Line code. The parameter type is LINE_CODE (line code).
•
Line code value is AMI.
•
Line code value is B8ZS (bipolar with eight-zero substitution).
•
Line Code HDB3. Only applicable to SDH E1 signal.
<FMT>
(Optional) Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.
•
SDH E1 CRCMF frame format
•
SDH E1 CRC frame format
•
SDH E1 MF frame format
•
SDH E1 unframed format
•
SDH E1 framed format
<LBO>
(Optional) BIS line build out settings. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line buildout).
•
BITS line buildout range is 0 to 133.
•
BITS line buildout range is 134 to 266.
•
BITS line buildout range is 267 to 399.
•
BITS line buildout range is 400 to 533.
•
BITS line buildout range is 534 to 655.
<SYNCMSG>
(Optional) Indicates if the BITS facility supports synchronization status message. Default is on (Y). The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<AISTHRSHLD>
(Optional) Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.
•
Do Not Use For Synchronization
•
ITU-T G.811 Standard
•
Reserved For Network Synchronization Use
•
ITU-T G.812T Standard
•
Synchronized, Traceability Unknown
•
ITU-T G.812TL Standard
•
Synchronous Equipment Timing Source
<SABIT>
(Optional) When the frame format selection is E1, SABIT is the BIT used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).
•
SABIT is BYTE-4.
•
SABIT is BYTE-5.
•
SABIT is BYTE-6.
•
SABIT is BYTE-7.
•
SABIT is BYTE-8.
<IMPEDANCE>
(Optional) When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port. The parameter type is IMPEDANCE, which is the terminal impedance of the BITS-IN port.
•
Impedance of 120 ohm
•
Impedance of 75 ohm
<BITSFAC>
(Optional) BITS facility settings. The parameter type is BITS_FAC, which is the BITS facility rate. 64 k and 6 MHz are only applicable to SDH.
•
2 MHz rate
•
64 K rate
•
6 MHz rate
•
E1 rate
<ADMSSM>
(Optional) SSM selectable. Only applicable to BITS-IN when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.
•
Do Not Use For Synchronization
•
ITU-T G.811 Standard
•
Reserved For Network Synchronization Use
•
ITU-T G.812T Standard
•
Synchronized, Traceability Unknown
•
ITU-T G.812TL Standard
•
Synchronous Equipment Timing Source
<PST>
(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
21.26 RTRV-BULKROLL-<STM_TYPE>
(Cisco ONS 15454 SDH) The Retrieve Bulkroll for STM4, STM64, STM1, or STM16 (RTRV-BULKROLL-STM_TYPE>) command retrieves roll data parameters on a line. See Table 27-1 for supported modifiers by platform.
Usage Guidelines
None
Category
Bridge and Roll
Security
Retrieve
Input Format
RTRV-BULKROLL-<OCN_TYPE>:[<TID>]:<SRC>:<CTAG>:::[CRSTYPE=<CRSTYPE>];
Input Example
RTRV-BULKROLL-STM4:CISCO:FAC-3-1:1:::VC3;
Input Parameters
<SRC>
Source AID from the "FACILITY" section.
<CRSTYPE>
One of the values: VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC12
Output Format
SID DATE TIME
M CTAG COMPLD
"<FROM>:RFROM=<RFROM>,RTO=<RTO>,RMODE=<RMODE>,VLDSIG=<VLDSIG>"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"VC4-3-1-1:RFROM=VC4-3-1-1,RTO=VC4-5-1-1,RMODE=AUTO,VLDSIG=Y"
;
Table 21-33 Output Parameter Support
<FROM>
One of the endpoints. Access identifier from the "FACILITY" section for line level rolling and bulk rolling.
<RFROM>
The termination point of the existing cross-connect that is to be rolled. AID is from the "VC" section.
<RTO>
The the termination point that will become a leg of the new cross-connection. AID is from the "VC" section.
<RMODE>
(Optional) The rolling mode of operation. The parameter type is RMODE, which specifies the roll mode.
•
Automatic. When a valid signal is available, the roll under AUTO mode will automatically delete the previous endpoint.
•
Manual. Enter the corresponding delete roll/bulkroll command to delete the previous endpoint.
<VLDSIG>
(Optional) The rolling mode of operation. The parameter type is ON_OFF (disable or enable an attribute).
•
Disable an attribute.
•
Enable an attribute.
21.27 RTRV-BWP-ETH
(Cisco ONS 15454SDH)
This command is used to retrieve a BandWidth Profile entry in BWP DB. The BWP DB is a collection of BWP used in a Network Element.
Usage Guidelines
The "ALL" AID is supported by this command.
If the AID is invalid, an IIAC (Invalid AID) error message is returned.
Category
Ethernet
Security
Retrieve
Input Format
RTRV-BWP-ETH:[<TID>]:<AID>:<CTAG>[::::];
Input Example
RTRV-BWP-ETH:ROCKS:BWP-10000:1;
Input Parameter
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>::[NAME=<NAME>],[CIR=<CIR>],[CBS=<CBS>],[PBS=<PBS>],[PIR=<PIR>],[CFMSTATE=<CFM_STATE>]:";
;
Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BWP-10000::NAME="MyBWP",CIR=10,CBS=1M,PBS=1M,PIR=20,CFMSTATE=Y:";
;Output Parameters
21.28 RTRV-CFM
(Cisco ONS 15454 SDH) The Retrieve Connectivity Fault Management (RTRV-CFM) command retrieves the Connectivity Fault Management (CFM) protocol state at the port level.
Usage Guidelines
•
•
Category
Port
Security
Retrieve
Input Format
RTRV-CFM:[<TID>]:<AID>:<CTAG>;
Input Example
RTRV-CFM:454-156:ETH-1-1-1:1;
Input Parameter
Table 21-36
<AID>
Access identifier from the "ETH" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>,<STATE>"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ETH-7-1-1,STATE=ENABLE"
;
Table 21-37 Output Parameter Support
<AID>
Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the "ETH" section.
<CFM_STATE>
Indicates whether the CFM is enabled or disabled on the port.
•
Indicates the CFM is enabled on the port.
•
Indicates the CFM is disabled on the port.
21.29 RTRV-CHGRP
(Cisco ONS 15454 SDH) The Retrieve Channel Group (RTRV-CHGRP) command retrieves the layer 2 channel group information of GE_XP and 10GE_XP ethernet cards.
Category
Channel Group
Security
Retrieve
Input Format
RTRV-CHGRP:[<TID>]:<aid>:<CTAG>[::::];
Input Example
RTRV-CHGRP::CHGRP-1-2:1;
Input Parameters
<AID>
Access identifier from the "CHGRP" section.
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:[LACPMODE=<LACPMODE>],[HASHINGALGO=<HASHINGALGO>],[NIMODE=<NIMODE>],[MACLEARNING=<MACLEARNING>],[INGRESSCOS=<INGRESSCOS>],[ETHERCETYPE=<ETHERCETYPE>],[ETHERSTYPE=>ETHERSTYPE>],[BPDU=<BPDU>],[QNQMODE=<QNQMODE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],[SPEED=<SPEED>],[EXPSPEED=<EXPSPEED>],[CIR=<CIR>,[CBS=<CBS>],[EBS=<EBS>]:<PST>,[<SST>]"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"CHGRP-1-1:LACPMODE=ACTIVE,HASHINGALGO=HASHING_SA_DA_VLAN_INCOMING_PORT,NIMODE=UNI,MACLEARNING=N,INGRESSCOS=0,ETHERCETYPE=8100,ETHERSTYPE
=8100,BPDU=Y,QNQMODE=SELECTIVE,MTU=9700,FLOWCTRL=ASYMMETRIC,
SPEED=AUTO,EXPSPEED=AUTO,CIR=100,CBS=4K,EBS=4K:OOS-MA,DSBLD"
;
Table 21-38 Output Parameter Support
<AID>
Access identifier from the "CHGRP" section.
<NIMODE>
Identifies the Ethernet Network Interface Mode.
•
(Default) Network-Network Interface Mode
•
User-Network Interface Mode
<LACPMODE>
LACP mode values
•
Manual mode of LACP
•
Active mode of LACP
•
Passive mode of LACP
<HASHINGALGO>
Hashing algorithm value
•
The Hashing Algorithm value is HASHING_SA_VLAN_INCOMING_PORT.
•
The Hashing Algorithm is HASHING_DA_VLAN_INCOMING_PORT.
•
The Hashing Algorithm is HASHING_SA_DA_VLAN_INCOMING_PORT.
•
The Hashing Algorithm is HASHING_SRC_IP_TCP_UDP.
•
The Hashing Algorithm is HASHING_DST_IP_TCP_UDP
•
The Hashing Algorithm is HASHING_SRC_DST_IP_TCP_UDP.
<MTU>
(Optional) Maximum transport unit. The parameter type is MTU_TYPE, which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.
•
10004. Indicates jumbo size.
•
1500
•
1548
•
9600. Indicates jumbo size.
•
64
•
9700. Indicates jumbo size.
<ATTACH >
Ethernet AID for the front end CE-MR-6 cards. Ethernet AID for the ethernet port on GE_XP and 10GE_XP card.
<DETACH>
To remove or detach the port.
<SPEED>
(Optional) The parameter type is ETHER_SPEED, which indicates Ethernet speed. Defaults to AUTO.
•
100 Megabits per second
•
10 Gigabits per second
•
10 Megabits per second
•
1 Gigabit per second
•
40 Gigabit per second
•
Enable auto negotiation with full duplex.
<EXPSPEED>
(Optional) Ethernet speed. The parameter type is ETHER_SPEED, which is the Ethernet speed.
•
100 Megabits per second
•
10 Gigabits per second
•
10 Megabits per second
•
1 Gigabit per second
•
Auto
<CIR>
Ingress committed information rate. The value ranges from 0 to 100. The default value is 100.
<CBS>
Ingress committed burst bucket size.
•
4 Kbit bucket size
•
16 Kbit bucket size
•
32 Kbit bucket size
•
64 Kbit bucket size
•
128 Kbit bucket size
•
256 Kbit bucket size
•
512 Kbit bucket size
•
1 Mbit bucket size
•
2 Mbit bucket size
•
4 Mbit bucket size
•
8 Mbit bucket size
•
16 Mbit bucket size
•
16 Kbit bucket size
<EBS>
Ingress excess burst bucket size.
<MACLEARNING>
MAC Address Learning Mode. This activates the MAC address learning on the interface to avoid packet broadcasting.
•
Enables the MAC learning on the interface.
•
Disables the MAC learning on the interface.
<INGRESSCOS>
Identifies the COS value set in the S-VLAN tag.
•
Set a Cos value
•
Use the Customer COS
•
The COS will be provisioned on CVLAN basis (QinQ selective mode)
<ETHERCETYPE>
Identifies a customer foreseen Ethernet type. If the customer uses a non-standard Ethernet type, the incoming packets will be accepted only if the CE-VLAN Ethernet type matches this parameter.
<ETHERSTYPE>
Identifies a customer foreseen Ethernet type. If the customer uses a non-standard Ethernet type, the incoming packets will be accepted only if the CE-VLAN Ethernet type matches this parameter.
<BPDU>
BPDU (Bridge Protocol Data Unit) management mode; Drop/Passthrough BPDU tagged packets.
•
Enables the BPDU tag.
•
Disables the BPDU tag.
<QNQMODE>
This is used to represent the QinQ mode operations.
•
The S-VLAN tag is added only on specified CE-VLANs. The other packets are dropped.
•
The S-VLAN tag is always performed where all packets having the S-VLAN-ID identified by TRNSPSVLAN parameter are allowed.
<TRNSPSVLAN>
VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.
<NAME>
(Optional) NAME is a string. User-assigned port name.
21.30 RTRV-CMD-SECU
(Cisco ONS 15454 SDH) The Retrieve Command Security (RTRV-CMD-SECU) command retrieves the current command security level of the command specified in the AID field.
Usage Guidelines
None
Category
Security
Security
Superuser
Input Format
RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;
Input Example
RTRV-CMD-SECU::INIT-REG:1;
Input Parameters
Output Format
SID DATE TIME
M CTAG COMPLD
"<AID>:<CAP>"
;Output Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
"INIT-REG:PROV"
;
21.31 RTRV-COND-<MOD2ALM>
(Cisco ONS 15454 SDH) The Retrieve Condition for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, CHGRP, DS1, DS3I, DVBASI, E1, E100, E1000, E3, E4, EC1, FSTE, G1000, ETH, GFPOS, GIGE, HDLC, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, MSISC, OCH, OMS, OTS, OTU2, OTU3, POS, RPRIF, STM1, STM4, STM16, STM64, STM1E, VC3, VC4-4C, VC4-6C, VC4-64C, VC4-8C, VC4-12C, VC4, VC4-16C, VC4-2C, VC4-3C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c,VC4-64c, VC11, VC12, VCG, VC11, VC12, WLEN, 3GVIDEO, HDSDI, ISC3STP1G, ISC3STP2G, OTU1, or SDSDI (RTRV-COND-<MOD2ALM>) command retrieves the current standing condition and state associated with an entity.
Usage Guidelines
The command supports the modifiers 3GVIDEO, OTU1, SDSDI, HDSDI, ISC3STP1G, and ISC3STP2G.
See Table 27-1 for supported modifiers by platform.
Category
Fault
Security
Retrieve
Input Format
RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];
Input Example
Cisco ONS 15454 SDH
RTRV-COND-OTU1::VFAC-14-3-1:1::OTUK-IAE;
Table 21-40 Input Parameter Support
<AID>
Access identifier from the "ALL" section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.
<TYPEREQ>
(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
•
Action occurs on the near end of the facility.
<DIRN>
The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.
•
Both transmit and receive directions
•
Receive direction only
Output Format
SID DATE TIME
M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"
;
Output Example
tcc2 2011-08-18 16:11:55
M 1 COMPLD
"VFAC-14-3-1,OTU1:MN,OTUK-IAE,NSA,08-18,12-58-24,NEND,RCV,\"OTUK: INCOMING ALIGNMENT ERROR\""
;
Table 21-41 Output Parameter Support
<AID>
Access identifier from the "ALL" section
<AIDTYPE>
(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2ALM—alarm type
•
1-Gigabit Fibre Channel payload
•
1-Gigabit fiber connectivity payload
•
1-Gigabit ISC3 compatible
•
2-Gigabit Fibre Channel payload
•
2-Gigabit fiber connectivity payload
•
3G-SDI video payload.
•
4-Gigabit Fibre Channel payload
•
4-Gigabit fiber connectivity payload
•
40-Gigabit Ethernet
•
5Gbps InfiniBand (IB_5G) payload
•
8-Gigabit Fibre Channel payload
•
Client facility for MXP/TXP cards
•
Channel group
•
DS3i-N-12 alarm
•
Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload
•
E1 alarm
•
E100 alarm
•
E1000 alarm
•
E3 alarm
•
E4 frame. Only applicable to STM1E port 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode
•
ETH facility
•
Fast Ethernet port alarm
•
G1000 alarm
•
Generic framing protocol over packet over SDH virtual port alarm
•
Gigabit Ethernet port alarm
•
1.5G HD-SDI video payload.
•
High-level data link control (HDLC) frame mode.
•
InterSystem Channel, a protocol defined by IBM (ISC1) payload
•
1-Gbps ISC3 Peer
•
2-Gbps ISC3 Peer
•
1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode
•
ISC-3 STP 1G video payload.
•
ISC-3 STP 2G video payload.
•
1-Gbps ISC1, ISC2, and ISC3 compatibility
•
MSISC
•
Optical channel
•
OCH termination
•
Optical Multiplex Section
•
Optical Transport Section
•
Optical Transport Unit Level 1
•
Optical Transport Unit Level 3
•
POS port alarm
•
Resilient Ethernet Protocol
•
270M SDI video payload.
•
STM1 alarm
•
STM1E facility, only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.
•
STM4 alarm
•
STM16 alarm
•
STM64 alarm
•
VC11 alarm
•
VC12 alarm
•
VC3 alarm
•
VC38C alarm
•
VC44C alarm
•
VC464C alarm
•
VC48C alarm
•
VC4 alarm
•
VC416C alarm
•
VC42C alarm
•
VC43C alarm
•
UDCDCC alarm
•
UCDF alarm
•
Virtual concatenation group alarm
•
Wavelength path provisioning
<NTFCNCDE>
(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.
•
The condition causing the alarm has cleared.
•
A critical alarm.
•
A major alarm.
•
A minor alarm.
•
The condition is not alarmed.
•
The alarm is not reported.
<TYPEREP>
The condition itself. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.
<SRVEFF>
(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.
•
The condition is non-service affecting.
•
The condition is service affecting.
<OCRDAT>
(Optional) Date when the specific event or violation occurred, MM-DD.
<OCRTM>
(Optional) Time when the specific event or violation occurred, HH-MM-SS.
<LOCN>
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.
•
Action occurs on the far end of the facility.
