Cisco ONS SDH TL1 Command Guide, Release 9.0
Chap 17: REPT commands
Download this chapter
Chap 17: REPT commandsChap 17: REPT commands
Download the complete book
Cisco ONS SDH TL1 Command Guide, Release 9.0Cisco ONS SDH TL1 Command Guide, Release 9.0 (PDF - 16 MB)
give_us_feedback

Table Of Contents

REPT Messages

17.1  REPT ALM <MOD2ALM>

17.2  REPT ALM BITS

17.3  REPT ALM COM

17.4  REPT ALM ENV

17.5  REPT ALM LMP

17.6  REPT ALM EQPT

17.7  REPT ALM SECU

17.8  REPT ALM SYNCN

17.9  REPT DBCHG

17.10  REPT EVT <MOD2ALM>

17.11  REPT EVT BITS

17.12  REPT EVT COM

17.13  REPT EVT ENV

17.14  REPT EVT EQPT

17.15  REPT EVT FXFR

17.16  REPT EVT IOSCFG

17.17  REPT EVT SECU

17.18  REPT EVT SESSION

17.19  REPT EVT SYNCN

17.20  REPT PM <MOD2>

17.21  REPT SW


REPT Messages

This chapter provides report (REPT) messages for the Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH.

17.1  REPT ALM <MOD2ALM>

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Report Alarm for 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, DS1, E100, E1000, E3, E4, EC1, ETH, FSTE, G1000, GFPOS, GIGE, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STM1, STM4, STM16, STM64, T1, T3, UDCDCC, UDCF, VC3,VC4,VC4-2c,VC4-3c,VC4-4c,VC4-8c,VC4-16c,VC4-64c, VC12, VCG, VT1, VT2, or WLEN (REPT ALM <MOD2ALM>) message reports an alarm condition against a facility, an RPR interface, or a path.

Note The E3, E4, ETH, FSTE, POS, STM1, STM4, STM 16, T3, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c, VC12, VCG, VT1, and VT2 are the only modifiers supported on the Cisco ONS 15310 MA SDH platform.

See Table 27-1 on page 27-1 for supported modifiers by platform.

Category

Fault

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM <MOD2ALM>
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],
[<DIRN>]:[<DESC>],[<AIDDET>]"
;

SID DATE TIME
** ATAG REPT ALM <MOD2ALM>
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],[
<DIRN>]:[<DESC>],[<AIDDET>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM STM4
"FAC-2-1:MJ,LOS,SA,08-01,14-25-59,,:\"LOSS OF SIGNAL\",STM4"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM STM4
"STM4-4-2-1:MJ,LOS,SA,08-01,14-25-59,,:\"LOSS OF SIGNAL\",STM4"
;

Table 17-1 REPT ALM <MOD2ALM Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.15  LINE" section on page 25-24.

Y

Y

Y

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared

Y

Y

Y

•CR

A critical alarm

Y

Y

Y

•MJ

A major alarm

Y

Y

Y

•MN

A minor alarm

Y

Y

Y

•NA

The condition is not alarmed

Y

Y

Y

•NR

The alarm is not reported

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed conditions (NA), and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting

Y

Y

Y

•SA

The condition is service affecting

Y

Y

Y

<OCRDAT>

(Optional) Date

Y

Y

Y

<OCRTM>

(Optional) Time

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<AIDDET>

(Optional) AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed. The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•32DMX-L

32-channel demultiplexer for L-band

Y

Y

N

•32WSS-L

32-channel wavelength switch selector for L-band

Y

Y

N

•AD-1B

Optical Add/Drop Multiplexer (OADM) 1-Band Filter

Y

Y

N

•AD-1C

OADM 1-Channel Filter

Y

Y

N

•AD-2C

OADM 2-Channel Filter

Y

Y

N

•AD-4B

OADM 4-Band Filter

Y

Y

N

•AD-4C

OADM 4-Channel Filter

Y

Y

N

•AICI

AIC-I card

Y

Y

N

•AIP

Alarm Indication Panel

Y

Y

N

•ALM-PWR

Alarm Power

Y

Y

Y

•ASAP-4

Any Service, Any Port (ASAP) carrier card with four pluggable interface module (PIM) slots.

Y

Y

N

•BP

The backplane of the NE

Y

Y

Y

•CE-MR-6

(ONS 15310 CL and ONS 15310 MA SDH) -Interface card which supports 10/100/1000MBPS ether facilities.

Y

Y

Y

•CE-100T-8

8-port 100T card

Y

Y

Y

•CE-1000-4

4-port GIGE mapper card

Y

Y

N

•CTX-2500

CTX 2500 card for ONS 15310 MA SDH

N

N

Y

•CRFT-TMG

Craft Timing

Y

Y

N

•DCC

The Data Communications Channel

Y

Y

Y

•DMX-32

Optical De/Multiplexed (DMX) 32 Channels

Y

Y

N

•DS3i-N-12

DS3i-N-12 card

Y

Y

N

•E1

E1 card

Y

Y

N

•E1-21-DS3-E3-3

(ONS 15310 MA SDH) E1, E3, DS3 card

N

N

Y

•E1-63-DS3-E3-3

(ONS 15310 MA SDH) E1, E3, DS3 card

N

N

Y

•E1-42

42-port E1 card

Y

Y

N

•E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

Y

Y

N

•E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E1N

E1N card

Y

Y

N

•E3

E3 card

Y

Y

N

•FILLER_CARD

Filler card

Y

Y

Y

•FMEC-155E-1TO1

FMEC card corresponding

     

•FMEC-SMZ-E1

FMEC card corresponding to E1 card

Y

Y

N

•FMEC-SMZ-E3

FMEC card corresponding to E3 card

Y

Y

N

•FTA

Fan Tray of the NE

Y

Y

N

•FTA1

Fan Tray 1 of the NE

Y

Y

N

•FTA2

Fan Tray 2 of the NE

Y

Y

N

•G1K-4

G1K-4 card

Y

Y

N

•MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

Y

Y

N

•ML100X-8

8-port 100T card with optical interface

Y

Y

N

•ML-100T-8

(Cisco ONS 15454 and Cisco ONS 15310 MA SDH) Exige/Elise mapper card

Y

N

Y

•ML-1000-2

(Cisco ONS 15454) Daytona 2-port GigE

Y

N

N

•ML-100T-12

((Cisco ONS 15454) Daytona) 12-port FSTE

Y

N

N

•MRC-12

!2-port

Y

Y

N

•MRC-2.5G-4

12G (4 * 2.5G) Muxponder card

Y

Y

N

•MRC-2.5G-12

12G (4 * 2.5G) Muxponder card

Y

Y

N

•MMU

Multiring mesh upgrade unit

Y

Y

N

•MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

Y

Y

N

•MUX-32

Optical Multiplexer (MUX) 32 Channels

Y

Y

N

•MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

Y

Y

N

•MXP-MR-10DME

10 Gbps datamux with enhanced FEC

Y

Y

N

•OPT-AMP-L

Optical preamplifier card for L-band

Y

Y

N

•OPT-BST

Optical booster amplifier

Y

Y

N

•OPT-BST-L

Optical booster for L-band

Y

Y

N

•OPT-PRE

Optical Preamplifier

Y

Y

N

•OPT-RAMP-C

Raman pump amplifier C-band

Y

N

N

•OSC-CSM

Optical Service Channel with Combiner/Separator Module

Y

Y

N

•OSCM

Optical Service Channel (OSC) Module

Y

Y

N

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-4

Pluggable interface module with 4 pluggable port module (PPM) slots

Y

Y

N

•PPM-1

Pluggable port module with 1 port SFP module

Y

Y

Y

•PSM

       

•SHELF

Shelf entity

Y

Y

Y

•STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-4

A four port STM4 card

Y

Y

N

•STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-SR-1

An interface card that supports one short range STM4 (622Mbps) optical facilities

Y

Y

N

•STM64-4

A four port STM64 card

Y

Y

N

•STM64-LR-1

An interface card that supports one or more STM64 optical facilities

Y

Y

N

•STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) asynchronous transfer mode (ATM) optical fibers

Y

Y

N

•STM1IR-STM1SH-
1310-8

An STM1 card that has 8 ports over the lower speed slot of the ONS 15454 SDH with XC-VXL-10G/XC-VXL-2.5G

Y

Y

N

•STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) packet-over-SDH (POS) optical facilities

Y

Y

N

•STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

Y

Y

Y

•STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

Y

Y

N

•STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

Y

Y

N

•STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

Y

Y

N

•TCC

Timing, Communications, and Control card

Y

Y

N

•TXP-MR-10G

10G Multirate Transponder card

Y

Y

N

•TXP-MR-2.5G

Multirate 2.5G Unprotected

Y

Y

N

•TXPP-MR-2.5G

Multirate 2.5G Protected

Y

Y

N

•UNKNOWN

Unknown equipment type

Y

Y

Y

•UNPROVISIONED

Unprovisioned equipment type

Y

Y

Y

•XC-VXC-10G

XC-VXC-10G cross-connect card

Y

Y

N

•XCVXL-10G

XC-VXL-10G cross-connect card

Y

Y

N

•XCVXL-2.5G

XC-VXL-2.5G cross-connect card

Y

Y

N


17.2  REPT ALM BITS

The Report Alarm Building Integrated Timing Supply (REPT ALM BITS) message reports an alarm condition on a BITS facility.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM BITS
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],
<DIRN>]:[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM BITS
"BITS-1:MJ,SYNC,SA,08-01,14-25-59,,:\"LOSS OF TIMING\""
;

Table 17-2 REPT ALM BITS Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.6  BITS" section on page 25-14.

Y

Y

Y

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed conditions (NA), and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions

Y

Y

Y

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting

Y

Y

Y

•SA

The condition is service affecting

Y

Y

Y

<OCRDAT>

(Optional) Date

Y

Y

Y

<OCRTM>

(Optional) Time

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y


17.3  REPT ALM COM

The Report Alarm Common (REPT ALM COM) message reports an alarm condition when an AID cannot be given, for example, a fan failure is reported using this message.

Usage Guidelines

None

Category

Fault

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM COM
"[<AID>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],
[<DIRN>]:[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM COM
"COM:MJ,FAN,NSA,08-01,14-25-59,,:\"FAN FAILURE\""
;

Table 17-3 REPT ALM COM Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

(Optional) Access identifier. Identifies the entity to which the command pertains. Indicates an alarm without AID. AID is a string.

Y

Y

Y

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed conditions (NA), and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting.

Y

Y

Y

•SA

The condition is service affecting.

Y

Y

Y

<OCRDAT>

(Optional) Date

Y

Y

Y

<OCRTM>

(Optional) Time

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y


17.4  REPT ALM ENV

The Report Alarm Environment (REPT ALM ENV) message reports a customer-defined condition on an environmental alarm input.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM ENV
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM ENV
"ENV-IN-1:MJ,OPENDR,08-01,14-25-59,\"OPEN DOOR\""
;

Table 17-4 REPT ALM ENV Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.11  ENV" section on page 25-20. Identifies an environmental input.

Y

Y

Y

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<ALMTYPE>

Abbreviated code identifying the alarm. The parameter type is ENV_ALM, which is the environmental alarm type.

Y

Y

Y

•AIRCOMPR

Air compressor failure

Y

Y

Y

•AIRCOND

Air conditioning failure

Y

Y

Y

•AIRDRYR

Air dryer failure

Y

Y

Y

•BATDSCHRG

Battery discharging

Y

Y

Y

•BATTERY

Battery failure

Y

Y

Y

•CLFAN

Cooling fan failure

Y

Y

Y

•CPMAJOR

Centralized power major failure

Y

Y

Y

•CPMINOR

Centralized power minor failure

Y

Y

Y

•ENGINE

Engine failure

Y

Y

Y

•ENGOPRG

Engine operating

Y

Y

Y

•ENGTRANS

Standby engine transfer

Y

Y

Y

•EXPLGS

Explosive gas

Y

Y

Y

•FIRDETR

Fire detector failure

Y

Y

Y

•FIRE

Fire

Y

Y

Y

•FLOOD

Flood

Y

Y

Y

•FUELLEAK

Fuel leak

Y

Y

Y

•FUSE

Fuse failure

Y

Y

Y

•GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

Y

Y

Y

•HATCH

Controlled Environment Vault (CEV) hatch fail

Y

Y

Y

•GEN

Generator failure

Y

Y

Y

•HIAIR

High airflow

Y

Y

Y

•HIHUM

High humidity

Y

Y

Y

•HITEMP

High temperature

Y

Y

Y

•HIWTR

High water

Y

Y

Y

•INTRUDER

Intrusion

Y

Y

Y

•LEVELCON

Level converter

Y

Y

Y

•LVDADSL

Secondary asymmetric digital subscriber line (ADSL) low voltage disconnect

Y

Y

Y

•LVDBYPAS

Low voltage disconnected bypass

Y

Y

Y

•LWBATVG

Low battery voltage

Y

Y

Y

•LWFUEL

Low fuel

Y

Y

Y

•LWHUM

Low humidity

Y

Y

Y

•LWPRES

Low cable pressure

Y

Y

Y

•LWTEMP

Low temperature

Y

Y

Y

•LWWTR

Low water

Y

Y

Y

•MISC

Miscellaneous

Y

Y

Y

•OPENDR

Open door

Y

Y

Y

•POWER

Commercial power failure

Y

Y

Y

•PUMP

Pump failure

Y

Y

Y

•PWR-48

48 V power supply failure

Y

Y

Y

•PWR-139

-139 V power converter

Y

Y

Y

•PWR-190

-190 V power converter

Y

Y

Y

•PWRMJ

Power supply major

Y

Y

Y

•PWRMN

Power supply minor

Y

Y

Y

•RECT

Rectifier failure

Y

Y

Y

•RECTHI

Rectifier high voltage

Y

Y

Y

•RECTLO

Rectifier low voltage

Y

Y

Y

•RINGGENMJ

Ringing generator major

Y

Y

Y

•RINGGENMN

Ringing generator minor

Y

Y

Y

•RTACADSL

AC or AC/rectifier power fail ADSL equipment

Y

Y

Y

•RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

Y

Y

Y

•RTACPWR

AC or AC/rectifier power fail DCL equipment

Y

Y

Y

•RTACPWRENG

Commercial AC fail, site equipped with standby engine

Y

Y

Y

•RTBAYPWR

AC power loss distributed power RT bay

Y

Y

Y

•RTRVENG

Retrieve standby engine, commercial AC restored

Y

Y

Y

•SMOKE

Smoke

Y

Y

Y

•TEMP

High-low temperature

Y

Y

Y

•TOXICGAS

Toxic gas

Y

Y

Y

•TREPEATER

T-repeater shelf

Y

Y

Y

•VENTN

Ventilation system failure

Y

Y

Y

<OCRDAT>

(Optional) Date.

Y

Y

Y

<OCRTM>

(Optional) Time.

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y


17.5  REPT ALM LMP

Note The REPT ALM LMP command does not apply to the Cisco ONS 15310 MA SDH platform.

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Report Alarm Link Management Protocol (REPT ALM LMP) autonomous message is used to report the LMP-FAIL alarms for the control channels and traffic engineering (TE) links.

Usage Guidelines

None

Category

Fault

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM LMP "[<AID>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],
[<DIRN>]:[<DESC>]"
;

Output Example

va454-5 1998-06-20 14:30:00
A 814.812 REPT ALM LMP
"CTRL-1:MJ,LMP-FAIL,NSA,08-01,14-25-59,,\"LMP Failure\","
;

Table 17-5 REPT ALM LMP Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

The LMP control channel AID value.

Y

Y

Y

•CTRL-ALL

Specifies all the control channels.

Y

Y

Y

•CTRL-{1-4}

Specifies an individual control channel.

Y

Y

Y

<NTFCNCDE>

The two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The condition is not reported.

Y

Y

Y

<CONDTYPE>

The condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454, ONS 15310-CL, or ONS 15600 shelf, whether or not the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, Not-Alarmed conditions (NA), and Not-Reported (NR) conditions. See Chapter 26, "" for a list of conditions.

Y

Y

Y

<SRVEFF>

Indicates the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting.

Y

Y

Y

•SA

The condition is service affecting.

Y

Y

Y

<OCRDAT>

(Optional) Date in YYYY-MM-DD format.

Y

Y

Y

<OCRTM>

(Optional) Time in HH:MM:SS format.

Y

Y

Y

<DESC>

Is a condition, alarm or event description.

Y

Y

Y


17.6  REPT ALM EQPT

The Report Alarm Equipment (REPT ALM EQPT) message reports an alarm condition against an equipment unit or slot.

Usage Guidelines

None

Category

Equipment

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM EQPT
"<AID>:<NTFCNCDE>,<CONDITION>,<SRVEFF>,[<OCRDAT>],[<OCRTM>,[<LOCN>],
[<DIRN>]:[<DESC>],[<AIDDET>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM EQPT
"SLOT-7:MJ,CONTR,NSA,08-01,14-25-59,,:\"CONTROLLER FAILURE\",TCC"
;

Cisco ONS 15600 SDH

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM EQPT
"SLOT-7:MJ,CONTR,NSA,08-01,14-25-59,NEND,RCV:\"CONTROLLER FAILURE\",TSC"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM EQPT
"SLOT-3:MJ,CONTR,NSA,08-01,14-25-59,NEND,RCV:\"CONTROLLER FAILURE\",CTX-2500"
;

Table 17-6 REPT ALM EQPT Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.12  EQPT" section on page 25-21. Equipment AID SLOT-{1-17}.

Y

Y

Y

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<CONDITION>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed conditions (NA), and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting.

Y

Y

Y

•SA

The condition is service affecting.

Y

Y

Y

<OCRDAT>

(Optional) Date

Y

Y

Y

<OCRTM>

(Optional) Time

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<AIDDET>

(Optional) AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed. The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•32DMX-L

3- channel demultiplexer for L-band

Y

Y

N

•32WSS-L

32-channel wavelength switch selector for L-band

Y

Y

N

•AD-1B

OADM 1-Band Filter

Y

Y

N

•AD-1C

OADM 1-Channel Filter

Y

Y

N

•AD-2C

OADM 2-Channel Filter

Y

Y

N

•AD-4B

OADM 4-Band Filter

Y

Y

N

•AD-4C

OADM 4-Channel Filter

Y

Y

N

•AICI

AIC-I card

Y

Y

N

•AIP

Alarm Indication Panel

Y

Y

N

•ALM-PWR

Alarm Power

Y

Y

Y

•ASAP-4

ASAP carrier card with four PIM slots

N

Y

N

•BP

The backplane of the NE

Y

Y

Y

•CE-100T-8

8-port 100T card

Y

Y

Y

•CE-1000-4

4-port GIGE mapper card

Y

Y

N

•CRFT-TMG

Craft Timing

Y

Y

N

•DCC

Data Communications Channel

Y

Y

Y

•DMX-32

Optical DMX 32 Channels

Y

Y

N

•DS3i-N-12

DS3i-N-12 card

Y

Y

N

•E1-21-DS3-E3-3

15310 MA SDH E1, E3, DS3 card

N

N

Y

•E1-63-DS3-E3-3

15310 MA SDH E1, E3, DS3 card

N

N

Y

•E1

E1 card

Y

Y

Y

•E1-42

42-port E1 card

Y

Y

N

•E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

Y

Y

N

•E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E1N

E1N card

Y

Y

N

•E3

E3 card

Y

Y

N

•FILLER_CARD

Filler card

Y

Y

Y

•FMEC-155E-1TO1

The equipment type for FMEC STM1E12 card

Y

N

N

•FMEC-SMZ-E1

FMEC card corresponding to E1 card

Y

Y

N

•FMEC-SMZ-E3

FMEC card corresponding to E3 card

Y

Y

N

•FTA

Fan Tray of the NE

Y

Y

N

•FTA1

Fan Tray 1 of the NE

Y

Y

N

•FTA2

Fan Tray 2 of the NE

Y

Y

N

•G1K-4

G1K-4 card

Y

Y

N

•MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

Y

Y

N

•ML100X-8

8-port 100X card with optical interface

Y

Y

N

•ML-100T-8

8-port 100T card with optical interface

Y

Y

N

•MMU

Multiring mesh upgrade unit

Y

Y

N

•MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

Y

Y

N

•MUX-32

Optical MUX 32 Channels

Y

Y

N

•MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

Y

Y

N

•MXP-MR-10DME

10 Gbps datamux with enhanced FEC

Y

Y

N

•OPT-AMP-L

Optical preamplifier for L-band

Y

Y

N

•OPT-BST

Optical booster amplifier

Y

Y

N

•OPT-BST-L

Optical booster for L-band

Y

Y

N

•OPT-PRE

Optical Preamplifier

Y

Y

N

•OPT-RAMP-C

Raman pump amplifier C-band

Y

N

N

•OSC-CSM

Optical Service Channel with Combiner/Separator Module

Y

Y

N

•OSCM

Optical Service Channel Module

Y

Y

N

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-4

Pluggable interface module with 4 PPM slots

Y

Y

N

•PPM-1

Pluggable port module with 1-port SFP module

Y

Y

Y

•PSM

       

•SHELF

Shelf entity

Y

Y

Y

•STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-4

A four port STM4 card

Y

Y

N

•STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-SR-1

An interface card that supports one short range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM64-4

A four port STM64 card

Y

Y

N

•STM64-LR-1

An interface card that supports one or more STM64 optical facilities

Y

Y

N

•STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) ATM optical fibers

Y

Y

N

•STM1IR-STM1SH-
1310-8

An STM1 card which has 8 ports over the lower speed slot of the ONS 15454 with XC-VXL-10G/XC-VXL-2.5G

Y

Y

N

•STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) POS optical facilities

Y

Y

N

•STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

Y

Y

Y

•STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

Y

Y

N

•STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

Y

Y

N

•STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

Y

Y

N

•TCC

Timing, Communications, and Control card

Y

Y

N

•TXP-MR-10G

10G Multirate Transponder card

Y

Y

N

•TXP-MR-2.5G

Multirate 2.5G Unprotected

Y

Y

N

•TXPP-MR-2.5G

Multirate 2.5G Protected

Y

Y

N

•UNKNOWN

Unknown equipment type

Y

Y

Y

•UNPROVISIONED

Unprovisioned equipment type

Y

Y

Y

•XC-VXC-10G

XC-VXC-10G cross-connect card

Y

Y

N

•XCVXL-10G

XC-VXL-10G cross-connect card

Y

Y

N

•XCVXL-2.5G

XC-VXL-2.5G cross-connect card

Y

Y

N


17.7  REPT ALM SECU

The Report Alarm Security (REPT ALM SECU) message reports the occurrence of an alarmed security event against the NE.

Usage Guidelines

Based on Telcordia TR-NWT-000835, the AID of the security alarm should be the Connection Identifier (CID), which is not currently supported.

The COM or UID is an acceptable substitute for the AID.

Note The INTRUSION-PSWD condition is the only condition that is reported as a standing condition instead of a transient condition. It defaults to NA and is reported by the REPT EVT SECU message. However, it can be reprovisioned to be reported at a higher severity. If the severity of this alarm is higher than NA, it is reported by the REPT ALM SECU message.

Category

Security

Security

Superuser

Output Format

SID DATE TIME
** ATAG REPT ALM SECU
"<AID>:<NOTIFCODE>,<SECUALMTYPE>"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM SECU
"COM:CR,INTRUSION-PSWD"
;

Table 17-7 REPT ALM SECU Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier. Identifies an entity with the condition. Defaults to COM. AID is a string.

Y

Y

Y

<NOTIFCODE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<SECUALMTYPE>

Security alarm type. It is a subset of the CONDITION type. In this release, the only allowable type is INTRUSION-PSWD. The parameter type is SECUALMTYPE, which is the security alarm type.

Y

Y

Y

•INTRUSION-PSWD

Condition raised after an invalid password is used during login. This condition is raised only if the password is used a specific number of times.

Y

Y

Y


17.8  REPT ALM SYNCN

The Report Alarm Synchronization (REPT ALM SYNCH) message reports an alarm condition against a synchronization reference.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT ALM SYNCN
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCN>],
[<DIRN>]:[<DESC>],
[<EQPTTYPE>]"
;

Output Example

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM SYNCN
"SYNC-NE:MJ,MAN,SA,08-01,14-25-59,,:\"MANUAL SWITCH\",TCC"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
** 100.100 REPT ALM SYNCN
"SYNC-NE:MJ,MAN,SA,08-01,14-25-59,,:\"MANUAL SWITCH\",CTX-2500"
;

Table 17-8 REPT ALM SYNCN Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.26  SYNC_REF" section on page 25-31. Identifies a synchronization reference with alarm condition.

Y

Y

Y

<NTFCNCDE>

Notification code. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

Y

Y

Y

•CL

The condition causing the alarm has cleared.

Y

Y

Y

•CR

A critical alarm.

Y

Y

Y

•MJ

A major alarm.

Y

Y

Y

•MN

A minor alarm.

Y

Y

Y

•NA

The condition is not alarmed.

Y

Y

Y

•NR

The alarm is not reported.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

Y

Y

Y

•NSA

The condition is non-service affecting.

Y

Y

Y

•SA

The condition is service affecting.

Y

Y

Y

<OCRDAT>

(Optional) Date

Y

Y

Y

<OCRTM>

(Optional) Time

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<EQPTTYPE>

(Optional) The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•10GE-XP

(ONS 15454) 2 x 10 Gbps. muxponder/L2 ethernet switch card

Y

Y

Y

•32-DMX

(ONS 15454) 32 channel optical demultiplexer

Y

Y

Y

•32-DMX-L

(ONS 15454) 32 channel optical demultiplexer for L-band

Y

Y

Y

•32-DMX-O

(ONS 15454) 32 channel unidirectional optical demultiplexer
This overrides the old equipment type DMX-32 present in the 4.6 and earlier releases.

Y

Y

Y

•32-MUX-O

(ONS 15454) 32 channel unidirectional optical multiplexer
This overrides the old equipment type MUX-32 present in the 4.6 and earlier releases.

Y

Y

Y

•32-WSS

(ONS 15454) 32 channel optical wavelength selective switch for C Band

Y

Y

Y

•40-DMX-C

(ONS 15454) 40 channel optical demultiplexer for C Band

Y

Y

Y

•40-MUX-C

(ONS 15454) 40 channel optical multiplexer for C Band

Y

Y

Y

•40-WSS-C

(ONS 15454) 40 channel optical wavelength switch selector for C Band

Y

Y

Y

•40-WXC-C

(ONS 15454) 40 channel optical wavelength cross-connect/wavelength router for C Band

Y

Y

Y

•AD-1B

(ONS 15454) Optical add/drop multiplexed (OADM) 1 band filter

Y

Y

Y

•AD-1C

(ONS 15454) Optical add/drop multiplexed (OADM) 1 channel filter

Y

Y

Y

•AD-2C

(ONS 15454) Optical add/drop multiplexed (OADM) 2 channels filter

Y

Y

Y

•AD-4B

(ONS 15454) Optical add/drop multiplexed (OADM) 4 bands filter

Y

Y

Y

•AD-4C

(ONS 15454) Optical add/drop multiplexed (OADM) 4 channels filter

Y

Y

Y

•ADM-10G

(ONS 15454) 16 x OC3/OC12/OC48/GIGE and OC192/Trunk ADM 10 Gbps card

Y

Y

Y

•AIC

(ONS 15454) AIC card

Y

Y

Y

•AICI

(ONS 15454) AICI Card

Y

Y

Y

•ASAP-4

(ONS 15600) Any service any port (ASAP) carrier card with four PIM slots

Y

Y

Y

•CE-1000-4

(ONS 15454) Modena mapper card

Y

Y

Y

•CE-100T-8

(ONS 15454, ONS 15310-CL, ONS 15310-MA) Exige/Elise mapper card

Y

Y

Y

•CE-MR-10

(ONS 15454, ONS 15454 SDH) Lotus20g ce2 card

Y

Y

Y

•CTX-2500

(ONS 15310-MA)CTX card

N

N

Y

•CXC

(ONS 15600) Cross connect card

Y

Y

Y

•DS1-28-DS3-EC1-3

(ONS 15310-MA) DS1-28-DS3-EC1-3 card

Y

Y

Y

•DS1-84-DS3-EC1-3

(ONS 15310-MA) DS1-84-DS3-EC1-3 card

Y

Y

Y

•DS1-E1-56

(ONS 15454) DS1-E1-56 card

Y

Y

Y

•DS1I

(ONS 15454) DS1I card

Y

Y

Y

•DS1N

(ONS 15454) DS1N card

Y

Y

Y

•DS3

(ONS 15454) DS3 card

Y

Y

Y

•E1-21-DS3-E3-3

E1-21-DS3-E3-3

N

N

Y

•E1-63-DS3-E3-3

E1-63-DS3-E3-3

N

N

Y

•FMEC-155E-1TO1

FMEC card

Y

Y

N

•CE-100T-8

CE-100T-8

Y

Y

Y

•OPT-RAMP-C

Raman pump amplifier C-band

Y

N

N

•OSCM

(ONS 15454) Optical service channel (OSC) module

Y

Y

Y

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-1

(ONS 15600) 1-port pluggable interface module

Y

Y

Y

•PIM-4

(ONS 15600) 4-port pluggable interface module

Y

Y

Y

•PPM-1

(ONS 15454, ONS 15600, ONS 15310-CL, ONS 15310-MA) Pluggable port module with one SFP port

Y

Y

Y

•PSM

       

•SSXC

(ONS 15600) Cross connect card

Y

Y

Y

•STM1E-12

(ONS 15454 SDH) STM1E-12 card

Y

Y

Y

•TCC

(ONS 15454) TCC card

Y

Y

N

•TXP-MR-10E

(ONS 15454) Skane 10G multirate transponder card with enhanced FEC

Y

Y

Y

•TXP-MR-10G

(ONS 15454) Skane 10G multirate transponder card

Y

Y

Y

•TXP-MR-2.5G

(ONS 15454) Rockwell multirate 2.5G unprotected

Y

Y

Y

•TXPP-MR-2.5G

(ONS 15454) Rockwell multirate 2.5G protected

Y

Y

Y

•XC

(ONS 15454) XC card

Y

Y

Y

•XC10G

(ONS 15454) XC10G card

Y

Y

Y

•XCVT

(ONS 15454) XCVT card

Y

Y

Y

•XCVXC-10G

(ONS 15454) XCVXC-10G card

Y

Y

Y

•XCVXC-2.5G

(ONS 15454) XCVXC-2.5G card

Y

Y

Y

•XCVXL-10G

(ONS 15454) XCVXL-10G card

Y

Y

Y

•XCVXL-2.5G

(ONS 15454) XCVXL-2.5G card

Y

Y

Y


17.9  REPT DBCHG

The Report Database Change (REPT DBCHG) message reports any changes on the NE that result from:

•TL1 provisioning commands or their graphical user interface (GUI) equivalents containing the verbs: ALW, DLT, ED, ENT, INH, INIT, OPR, RLS, SET, and SW (for example, DLT-EQPT, ENT-CRS-VC3).

•External event such as a board insertion.

When secondary state is changed from AutomaticInService state to any other state, no REPT DBCHG messages are generated.

Usage Guidelines

•The REPT DBCHG is turned off by default. To turn REPT DBCHG on, you must issue the ALW-MSG-DBCHG command.

•<SOURCE> and <USERID> are optional string parameters with a maximum length of 20 characters.

•<COMMAND> is a string parameter with a maximum length of 20 characters.

•<AID> is a string parameter with a maximum length of 64 characters. Any excess characters will be truncated.

•REPT DBCHG messages will be generated every time a roll is performed. A cross-connect delete and add REPT DBCHG message will not be sent every time a roll is performed.

Category

Log

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT DBCHG
"TIME=<TIME>,DATE=<DATE>,[SOURCE=<SOURCE>],[USERID=<USERID>],
DBCHGSEQ=<DBCHGSEQ>:<COMMAND>:[<AID>]:::[<PSTPSTQ>,],<SST>"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100 REPT DBCHG
"TIME=14-35-46,DATE=99-07-28,SOURCE=123,USERID=CISCO15,DBCHGSEQ=456:
ENT-CRS-VC4:VC4-4-1-2-6-4:::Locked-Enabled, AutomaticInService"
;

Table 17-9 REPT DBCHG Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<TIME>

The time of the message triggered by the NE.

Y

Y

Y

<DATE>

The date of the message triggered by the NE.

Y

Y

Y

<SOURCE>

(Optional) An input-command CTAG if present. SOURCE is a string.

Y

Y

Y

<USERID>

(Optional) The user name or user identifier. USERID is a string.

Y

Y

Y

<DBCHGSEQ>

Identifier or range of identifiers to be retrieved. It is a sequential number of the DBCHGSEQ message. DBCHSEQ is an integer

Y

Y

Y

<COMMAND>

The input command or substitute. COMMAND is a string.

Y

Y

Y

<AID>

Access identifier. AID is a string.

Y

Y

Y

•Unlocked-Disabled

Out of service and autonomous

Y

Y

Y

•Locked-Disabled

Out of service and autonomous and management

Y

Y

Y

•Locked-Enabled

Out of service and management

Y

Y

Y

<SST>

Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

Y

•AutomaticInService

Automatic in service

Y

Y

Y

•Disabled

Disabled

Y

Y

Y

•Loopback

Loopback

Y

Y

Y

•MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

Y

•Maintenance

Maintenance mode

Y

Y

Y

•OutOfGroup

Out of group

Y

Y

Y

•SoftwareDownload

Software downloading

Y

Y

Y

•Unassigned

Unassigned

Y

Y

Y

•NotInstalled

Unequipped

Y

Y

Y


17.10  REPT EVT <MOD2ALM>

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Report Event for 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, DS1, E100, E1000, E3, E4, EC1, ETH, FSTE, G1000, GFPOS, GIGE, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STM1,STM4,STM16,STM64, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c,VC4-64c, VC12, VCG, VT1, VT2, WLEN, or RPRIF (REPT EVT <MOD2ALM>) message reports the occurrence of a nonalarmed event. In Software Release 5.0 and later, REPT EVT <MOD2ALM> can report the remote monitoring (RMON)-managed threshold crossing alarm. See Table 27-1 on page 27-1 for supported modifiers by platform.

Note The E1, E3, E4, ETH, FSTE, POS, STM1,STM4,STM16, T1, T3, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c, VC12, VCG, are the only supported modifiers on the Cisco ONS 15310 MA SDH platform.

Usage Guidelines

None

Category

Fault

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT <MOD2ALM>
"<AID>:<CONDTYPE>,[<CONDEFF>],,,[<LOCN>],[<DIRN>],[<MONVAL>],[<THLEV>],
[<TMPER>]:[<DESC>],[<AIDDET>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT STM16
"FAC-5-1:WKSWPR,TC,,,FEND,,12,13,15-MIN:\"WORKING SWITCH TOPROTECTION\",
STM16"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT STM16
"STM16-4-1-1:WKSWPR,TC,,,FEND,,12,13,15-MIN:\"WORKING SWITCH TOPROTECTION\",
STM16"
;

Table 17-10 REPT EVT <MOD2ALM> Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.1  ALL" section on page 25-1.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1for a list of conditions.

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<LOCN>

(Optional) Location associated with a particular command in reference to the entity identified by the AID. The parameter type is LOCATION, which is the location where the action is to take place.

Y

Y

Y

•FEND

Action occurs on the Far End of the facility.

Y

Y

Y

•NEND

Action occurs on the Near End of the facility.

Y

Y

Y

<DIRN>

Direction relative to the entity identified by the AID. Direction of PM relative to the entity identified by the AID. The parameter type is DIRECTION (transmit and receive directions).

Y

Y

Y

•BTH

Both transmit and receive directions

Y

Y

Y

•RCV

Receive direction only

Y

Y

Y

•TRMT

Transmit direction only

Y

Y

Y

<MONVAL>

(Optional) Monitored value. Value to which the register identified by MONTYPE is to be initialized to or the measured value of a monitored parameter. The value is in the form of numeric counts or rates. MONVAL is a float.

Y

Y

Y

<THLEV>

(Optional) Threshold level. THLEV is a float.

Y

Y

Y

<TMPER>

(Optional) Accumulation time period for performance counters. The parameter type is TMPER, which is the accumulation time period for the performance management center.

Y

Y

Y

•1-DAY

Performance parameter accumulation interval length; every 24-hours. For SDH PM data only one day of history data is available. For RMON managed PM data seven days of history data are available.

Y

Y

Y

•1-HR

Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available.

Y

Y

Y

•1-MIN

Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available.

Y

Y

Y

•15-MIN

Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length.

Y

Y

Y

•RAW-DATA

Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs.

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<AIDDET>

(Optional) AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed. The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•32DMX-L

32 channels demultiplexer for L-band

Y

Y

Y

•32WSS-L

32 channels wavelength switch selector for L-band

Y

Y

Y

•AD-1B

OADM 1-Band Filter

Y

Y

Y

•AD-1C

OADM 1-Channel Filter

Y

Y

Y

•AD-2C

OADM 2-Channel Filter

Y

Y

Y

•AD-4B

OADM 4-Band Filter

Y

Y

Y

•AD-4C

OADM 4-Channel Filter

Y

Y

Y

•AICI

AIC-I card

Y

Y

Y

•AIP

Alarm Indication Panel

Y

Y

Y

•ALM-PWR

Alarm Power

Y

Y

Y

•ASAP-4

ASAP carrier card with four PIM slots

Y

Y

Y

•BP

The backplane of the NE

Y

Y

Y

•CE-100T-8

8-port 100T card

Y

Y

Y

•CE-1000-4

4-port GIGE mapper card

Y

Y

Y

•CRFT-TMG

Craft Timing

Y

Y

Y

•DCC

Data Communications Channel

Y

Y

Y

•DMX-32

Optical DMX 32 Channels

Y

Y

Y

•DS3i-N-12

DS3i-N-12 card

Y

Y

Y

•E1-21-DS3-E3-3

ONS 15310 MA SDH E1, E3, DS3 card

Y

Y

Y

•E1-63-DS3-E3-3

ONS 15310 MA SDH E1, E3, DS3 card

Y

Y

Y

•E1

E1 card

Y

Y

Y

•E1-42

42-port E1 card

Y

Y

Y

•E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

Y

Y

Y

•E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

Y

Y

Y

•E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

Y

Y

Y

•E1N

E1N card

Y

Y

Y

•E3

E3 card

Y

Y

Y

•FILLER_CARD

Filler card

Y

Y

Y

•FMEC-SMZ-E1

FMEC card corresponding to E1 card

Y

Y

Y

•FMEC-SMZ-E3

FMEC card corresponding to E3 card

Y

Y

Y

•FTA

Fan Tray of the NE

Y

Y

Y

•FTA1

Fan Tray 1 of the NE

Y

Y

Y

•FTA2

Fan Tray 2 of the NE

Y

Y

Y

•G1K-4

G1K-4 card

Y

Y

Y

•MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

Y

Y

Y

•ML100X-8

8-port 100T card with optical interface

Y

Y

Y

•ML-100T-8

(Cisco ONS 15454 and Cisco ONS 15310 MA SDH) Exige/Elise mapper card

Y

Y

Y

•MMU

Multiring mesh upgrade unit

Y

Y

Y

•MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

Y

Y

Y

•MUX-32

Optical MUX 32 Channels

Y

Y

Y

•MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

Y

Y

N

•MXP-MR-10DME

10 Gbps datamux with enhanced FEC

Y

Y

Y

•OPT-AMP-L

Optical preamplifier for L-band

Y

Y

Y

•OPT-BST

Optical booster amplifier

Y

Y

Y

•OPT-BST-L

Optical booster for L-band

Y

Y

Y

•OPT-PRE

Optical Preamplifier

Y

Y

Y

•OPT-RAMP-C

Raman Pump Amplifier C Band

Y

N

N

•OSC-CSM

Optical Service Channel with Combiner/Separator Module

Y

Y

Y

•OSCM

Optical Service Channel Module

Y

Y

Y

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-4

Pluggable interface module with 4 PPM slots

Y

Y

Y

•PPM-1

Pluggable port module with 1-port SFP module

Y

Y

Y

•PSM

       

•SHELF

Shelf entity

Y

Y

Y

•STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-4

A four port STM4 card

Y

Y

Y

•STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-SR-1

An interface card that supports one short range STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM64-4

A four port STM64 card

Y

Y

Y

•STM64-LR-1

An interface card that supports one or more STM64 optical facilities

Y

Y

Y

•STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) ATM optical fibers

Y

Y

Y

•STM1IR-STM1SH-
1310-8

An STM1 card which has 8 ports over the lower speed slot of the ONS 15454 SDH with XC-VXL-10G/XC-VXL-2.5G

Y

Y

Y

•STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) POS optical facilities

Y

Y

Y

•STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

Y

Y

Y

•STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

Y

Y

Y

•STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

Y

Y

Y

•STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

Y

Y

Y

•STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

Y

Y

Y

•STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

Y

Y

Y

•TCC

Timing, Communications, and Control card

Y

Y

Y

•TXP-MR-10G

10G Multirate Transponder card

Y

Y

Y

•TXP-MR-2.5G

Multirate 2.5G Unprotected

Y

Y

Y

•TXPP-MR-2.5G

Multirate 2.5G Protected

Y

Y

Y

•UNKNOWN

Unknown equipment type

Y

Y

Y

•UNPROVISIONED

Unprovisioned equipment type

Y

Y

Y

•XC-VXC-10G

XC-VXC-10G cross-connect card

Y

Y

Y

•XCVXL-10G

XC-VXL-10G cross-connect card

Y

Y

Y

•XCVXL-2.5G

XC-VXL-2.5G cross-connect card

Y

Y

Y


17.11  REPT EVT BITS

The Report Event Building Integrated Timing Supply (REPT EVT BITS) message reports a nonalarmed event against a BITS facility.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Output Format

SID DATE TIME
** ATAG REPT EVT BITS
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,[<LOCN>],[<DIRN>]:[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT BITS
"BITS-1:SSM-STU,TC,,,,,,,:\"SYNCHRONIZED - TRACEABILITY UNKNOWN\""
;

Table 17-11 REPT EVT BITS Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.6  BITS" section on page 25-14.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

 

17.12  REPT EVT COM

The Report Event Common (REPT EVT COM) message reports a nonalarmed event against an NE when there is no AID associated with it.

Usage Guidelines

None

Category

Fault

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT COM
"[<AID>]:<CONDTYPE>,[<CONDEFF>],,,,,,[<LOCN>],[<DIRN>]:[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT COM
"COM:CLDRESTART,TC,,,,,,,:\"COLD RESTART\","
;

Table 17-12 REPT EVT COM Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

(Optional) Access identifier. Identifies the entity to which the command pertains. AID is a string.

Y

Y

Y

<CONDTYPE>

(Optional) Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<CONDEFF>

The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y


17.13  REPT EVT ENV

The Report Event Environment (REPT EVT ENV) message reports the occurrence of a nonalarmed event against an environment alarm input.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT ENV
"<AID>:<ALMTYPE>,[<CONDEFF>],,,,,,[<LOCN>],[<DIRN>]:[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT ENV
"ENV-IN-2:OPENDR,TC,,,,,,,:\"OPEN DOOR\""
;

Table 17-13 REPT EVT ENV Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.11  ENV" section on page 25-20. Identifies an environmental input.

Y

Y

Y

<ALMTYPE>

Abbreviated code identifying the alarm. The parameter type is ENV_ALM, which is the environmental alarm type.

Y

Y

Y

•AIRCOMPR

Air compressor failure

Y

Y

Y

•AIRCOND

Air conditioning failure

Y

Y

Y

•AIRDRYR

Air dryer failure

Y

Y

Y

•BATDSCHRG

Battery discharging

Y

Y

Y

•BATTERY

Battery failure

Y

Y

Y

•CLFAN

Cooling fan failure

Y

Y

Y

•CPMAJOR

Centralized power major failure

Y

Y

Y

•INTRUDER

Intrusion

Y

Y

Y

•LEVELCON

Level converter

Y

Y

Y

•LVDADSL

Secondary ADSL low voltage disconnect

Y

Y

Y

•LVDBYPAS

Low voltage disconnect bypass

Y

Y

Y

•LWBATVG

Low battery voltage

Y

Y

Y

•LWFUEL

Low fuel

Y

Y

Y

•LWHUM

Low humidity

Y

Y

Y

•LWPRES

Low cable pressure

Y

Y

Y

•LWTEMP

Low temperature

Y

Y

Y

•LWWTR

Low water

Y

Y

Y

•MISC

Miscellaneous

Y

Y

Y

•OPENDR

Open door

Y

Y

Y

•POWER

Commercial power failure

Y

Y

Y

•PUMP

Pump failure

Y

Y

Y

•PWR-48

48 V power supply failure

Y

Y

Y

•PWR-139

-139 V power converter

Y

Y

Y

•PWR-190

-190 V power converter

Y

Y

Y

•PWRMJ

Power supply major

Y

Y

Y

•PWRMN

Power supply minor

Y

Y

Y

•RECT

Rectifier failure

Y

Y

Y

•RECTHI

Rectifier high voltage

Y

Y

Y

•RECTLO

Rectifier low voltage

Y

Y

Y

•RINGGENMJ

Ringing generator major

Y

Y

Y

•RINGGENMN

Ringing generator minor

Y

Y

Y

•RTACADSL

AC or AC/rectifier power fail ADSL equipment

Y

Y

Y

•RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

Y

Y

Y

•RTACPWR

AC or AC/rectifier power fail DCL equipment

Y

Y

Y

•RTACPWRENG

Commercial AC fail, site equipped with standby engine

Y

Y

Y

•RTBAYPWR

AC power loss distributed power RT bay

Y

Y

Y

•RTRVENG

Retrieve standby engine, commercial AC restored

Y

Y

Y

•SMOKE

Smoke

Y

Y

Y

•TEMP

High-low temperature

Y

Y

Y

•TOXICGAS

Toxic gas

Y

Y

Y

•TREPEATER

T-repeater shelf

Y

Y

Y

•VENTN

Ventilation system failure

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y


17.14  REPT EVT EQPT

The Report Event Equipment (REPT EVT EQPT) message reports the occurrence of a nonalarmed event against an equipment unit or slot.

Usage Guidelines

None

Category

Equipment

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT EQPT
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,[<LOCN>],[<DIRN>]:[<DESC>],[<AIDDET>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT EQPT
"SLOT-7:PLUGIN,TC,,,,,,,:\"EQUIPMENT PLUG-IN\",TCC"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT EQPT
"SLOT-3:PLUGIN,TC,,,,,,,:\"EQUIPMENT PLUG-IN\",CTX-2500"
;

Table 17-14 REPT EVT EQPT Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.12  EQPT" section on page 25-21. Equipment AID SLOT-{1-17}.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<AIDDET>

(Optional) AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed. The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•32DMX-L

32-channel demultiplexer for L-band

Y

Y

Y

•32WSS-L

32-channel wavelength switch selector for L-band

Y

Y

Y

•AD-1B

OADM 1-Band Filter

Y

Y

Y

•AD-1C

OADM 1-Channel Filter

Y

Y

Y

•AD-2C

OADM 2-Channel Filter

Y

Y

Y

•AD-4B

OADM 4-Bans Filter

Y

Y

Y

•AD-4C

OADM 4-Channel Filter

Y

Y

Y

•AICI

AIC-I card

Y

Y

Y

•AIP

Alarm Indication Panel

Y

Y

Y

•ALM-PWR

Alarm Power

Y

Y

Y

•ASAP-4

ASAP carrier card with four PIM slots

Y

Y

Y

•BP

The backplane of the NE

Y

Y

Y

•CE-100T-8

8-port 100T card

Y

Y

Y

•CE-1000-4

4-port GIGE mapper card

Y

Y

Y

•CRFT-TMG

Craft Timing

Y

Y

Y

•DCC

Data Communications Channel

Y

Y

Y

•DMX-32

Optical DMX 32 Channels

Y

Y

Y

•DS3i-N-12

DS3i-N-12 card

Y

Y

Y

•E1-21-DS3-E3-3

ONS 15310 MA SDH E1, E3, DS3 card

Y

Y

Y

•E1-63-DS3-E3-3

ONS 15310 MA SDH E1, E3, DS3 card

Y

Y

Y

•E1

E1 card

Y

Y

Y

•E1-42

42-port E1 card

Y

Y

N

•E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

Y

Y

N

•E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E1N

E1N card

Y

Y

N

•E3

E3 card

Y

Y

N

•FILLER_CARD

Filler card

Y

Y

Y

•FMEC-155E-1TO1

The equipment type for FMEC STM1E12 card

Y

N

N

•FMEC-SMZ-E1

FMEC card corresponding to E1 card

Y

Y

N

•FMEC-SMZ-E3

FMEC card corresponding to E3 card

Y

Y

N

•FTA

Fan Tray of the NE

Y

Y

N

•FTA1

Fan Tray 1 of the NE

Y

Y

N

•FTA2

Fan Tray 2 of the NE

Y

Y

N

•G1K-4

G1K-4 card

Y

Y

N

•MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

Y

Y

N

•ML100X-8

8-port 100T card with optical interface

Y

Y

N

•MMU

Multiring mesh upgrade unit

Y

Y

N

•MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

Y

Y

N

•MUX-32

Optical MUX 32 Channels

Y

Y

N

•MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

Y

Y

N

•MXP-MR-10DME

10 Gbps datamux with enhanced FEC

Y

Y

N

•OPT-AMP-L

Optical preamplifier for L-band

Y

Y

N

•OPT-BST

Optical booster amplifier

Y

Y

N

•OPT-BST-L

Optical booster for L-band

Y

Y

N

•OPT-PRE

Optical Preamplifier

Y

Y

N

•OPT-RAMP-C

Raman Pump Amplifier C Band

Y

N

N

•OSC-CSM

Optical Service Channel with Combiner/Separator Module

Y

Y

N

•OSCM

Optical Service Channel Module

Y

Y

N

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-4

Pluggable interface module with 4 PPM slots

Y

Y

N

•PPM-1

Pluggable port module with 1-port SFP module

Y

Y

Y

•PSM

       

•SHELF

Shelf entity

Y

Y

N

•STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-4

A four port STM4 card

Y

Y

N

•STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-SR-1

An interface card that supports one short range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM64-4

A four-port STM64 card

Y

Y

N

•STM64-LR-1

An interface card that supports one or more STM64 optical facilities

Y

Y

N

•STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) ATM optical fibers

Y

Y

N

•STM1IR-STM1SH-
1310-8

An STM1 card which has 8 ports over the lower speed slot of the ONS 15454 SDH with XC-VXL-10G/XC-VXL-2.5G

Y

Y

N

•STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) POS optical facilities

Y

Y

N

•STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

Y

Y

Y

•STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

Y

Y

N

•STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

Y

Y

N

•STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

Y

Y

N

•TCC

Timing, Communications, and Control card

Y

Y

Y

•TXP-MR-10G

10G Multirate Transponder card

Y

Y

Y

•TXP-MR-2.5G

Multirate 2.5G Unprotected

Y

Y

Y

•TXPP-MR-2.5G

Multirate 2.5G Protected

Y

Y

Y

•UNKNOWN

Unknown equipment type

Y

Y

Y

•UNPROVISIONED

Unprovisioned equipment type

Y

Y

Y

•XC-VXC-10G

XC-VXC-10G cross-connect card

Y

Y

Y

•XCVXL-10G

XC-VXL-10G cross-connect card

Y

Y

Y

•XCVXL-2.5G

XC-VXL-2.5G cross-connect card

Y

Y

Y


17.15  REPT EVT FXFR

Note The REPT EVT FXFR message command does not apply to the Cisco ONS 15310 MA SDH platform.

The Report Event Software Download (REPT EVT FXFR) message reports the FTP software download status of the start, completion, and completed percentage.

Usage Guidelines

•The FXFR_RSLT is only sent when the FXFR_STATUS is COMPLD.

•The PRCNT_XFRD is only sent when the FXFR_STATUS is IP or COMPLD.

Category

File Transfer

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT FXFR
"<FILENAME>,<FXFR_STATUS>,[<FXFR_RSLT>],[<PRCNT_XFRD>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT FXFR
"NEW.PKG,COMPLD,SUCCESS,21215147"
;

Table 17-15 REPT EVT FXFR Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<FILENAME>

When a package is being transferred between the FTP server and the controller cards, the filename field will contain the string ACTIVE. Following this transfer, if there is a second controller card on the NE, the file will be copied over to the second card during which time REPT EVT FXFR messages will be generated with a filename of STANDBY. FILENAME is a string.

Y

Y

N/A

<FXFR_STATUS>

The status of the file transfer: Start, IP (in progress), or COMPLD. The parameter type is TX_STATUS, which is the status of the file transfer.

Y

Y

N/A

•COMPLD

The file transmission is completed.

Y

Y

N/A

•IP

The file transmission is in progress.

Y

Y

N/A

•START

The file transmission is started.

Y

Y

N/A

<FXFR_RSLT>

(Optional) The result of the file transfer: Success or Failure. The parameter type is TX_RSLT, which is the result of the file transfer.

Y

Y

N/A

•FAILURE

A failed result

Y

Y

N/A

•SUCCESS

A successful result

Y

Y

N/A

<PRCNT_XFRD>

(Optional) The percentage transfer complete. PRCNT_XFRD is a string.

Y

Y

N/A


17.16  REPT EVT IOSCFG

The Report Event Cisco IOS Configuration File (REPT EVT IOSCFG) message reports the status of copying the Cisco IOS configuration file when the COPY-IOSCFG command is issued.

Usage Guidelines

•You can identify if this message is caused by a Cisco IOS configuration file downloading, uploading or merging by looking at the SRC and DEST field in the message. Refer to the COPY-IOSCFG command for more details.

•There is no success/failure in the message to indicate the success or failure of the merge process when merging the startup Cisco IOS configuration file to the running configuration file.

Category

File Transfer

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT IOSCFG
"<AID>:<SRC>,<DEST>,<STATUS>,[<RESULT>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT IOSCFG
"SLOT-1:STARTUP,IOS-CONFIG-FILE-IN-NETWORK,COMPLD,SUCCESS"
;

Table 17-16 REPT EVT IOSCFG Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.12  EQPT" section on page 25-21. Slot AID for the equipment.

Y

Y

Y

<SRC>

Source access identifier. Specifies where the Cisco IOS config file is copied from. SRC is a string.

Y

Y

Y

<DEST>

Destination. Specifies where the Cisco IOS config file is copied to. DEST is a string.

Y

Y

Y

<STATUS>

The status of COPY-IOSCFG: Start, IP, or COMPLD. The parameter type is TX_STATUS, which is the status of the file transfer.

Y

Y

Y

•COMPLD

The file transmission is completed.

Y

Y

Y

•IP

The file transmission is in progress.

Y

Y

Y

•START

The file transmission is started.

Y

Y

Y

<RESULT>

(Optional) The result of the file transfer: Success or Failure. the parameter type is TX_RSLT, which is the result of the file transfer.

Y

Y

Y

•FAILURE

A failed result

Y

Y

Y

•SUCCESS

A successful result

Y

Y

Y


17.17  REPT EVT SECU

The Report Event Security (REPT-EVT-SECU) message reports the occurrence of a nonalarmed security event against the NE. Based on Telcordia TR-NWT-000835.

Usage Guidelines

•The AID of the security alarm should be the CID, which is not supported in this release. The COM or UID is an acceptable substitute for the AID here. CIDs will be supported in a future release.

•For the rule of single failure, single message/alarm, the security alarm will not be reported as REPT ALM COM, because it is reported as REPT ALM SECU.

•Because the NE sends this security message as a transient message, to make all TL1 autonomous messages consistent, the TL1 agent reports the security message into REPT EVT SECU.

•This message is inhibited by default. A Superuser will have to issue the ALW-MSG-SECU to see this message.

Category

Security

Security

Superuser

Output Format

SID DATE TIME
A ATAG REPT EVT SECU
"<AID>:<DNFIELD>,[<CONDEFF>],,,[<LOCN>],[<DIRN>],,,:<SECURITY>:<DNFIELD1>"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT SECU
"COM:LOGIN-FAILURE-PSWD,TC,,,,,,,:\"SECURITY:
INVALID LOGIN - PASSWORD - SEE AUDIT LOG\""
;

Table 17-17 REPT EVT SECU Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier. Identifies an entity with the condition. Defaults to COM. AID is a string.

Y

Y

Y

<DNFIELD>

String.

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

•RCV

Receive direction only

Y

Y

Y

•TRMT

Transmit direction only

Y

Y

Y

<SECURITY>

The category of condition. SECURITY is a string.

Y

Y

Y

<DNFIELD1>

DNFIELD1 is a string.

Y

Y

Y


17.18  REPT EVT SESSION

The Report Event Session (REPT EVT SESSION) message reports a nonalarmed event related to establishing a session with the NE.

Usage Guidelines

The WARN field might contain different information depending on the type of session-related event.

•If the password aging feature has not been enabled (or the feature is enabled but the password is not close to expiring):

/*USER <UID> LOGGED IN <IP/SERIAL PORT*/

•If the forced password feature is enforced and the user is logging in for the first time (or the password has expired):

/*PLEASE CHANGE PASSWORD BEFORE CONTINUING*/

•If a session is terminated for any reason (except a user timeout), the reason for the session termination is indicated in the warning (<WARN>).

Category

Security

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT SESSION
"<AID>:<EXP>,<PCN>"
"<WARN>"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT SESSION
"TCCP:YES,5-DAY"
"/* USER TERRI LOGGED IN TO TCCP */"
;

Table 17-18 REPT EVT SESSION Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier. Identifies the NE with which a session is established. AID is a string.

Y

Y

Y

<EXP>

Indicates whether the password is alive (for example, no password updating is required at the moment), expired, or is about to expire. the parameter type is YES_NO, which indicates whether the user's password is about to expire, the user is logged into the NE or the user is locked out of the NE.

Y

Y

Y

•NO

No

Y

Y

Y

•YES

Yes

Y

Y

Y

<PCN>

The number of days still remaining before the existing password expires. PCN is a string. PCN appears only if EXP=YES and one of the following conditions exists:

•The warning period has not been exhausted

•The user is a new user establishing a session for the first time and the forced password change policy has been activated.

Y

Y

Y

<WARN>

Free format text containing additional information about the security event. WARN is a string.

Y

Y

Y


17.19  REPT EVT SYNCN

The Report Event Synchronization (REPT EVT SYNCN) message reports the occurrence of a non-alarmed event against a synchronization entity.

Usage Guidelines

None

Categories

Synchronization

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT EVT SYNCN
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,[<LOCN>],[<DIRN>]:[<DESC>],[<AIDDET>]"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT SYNCN
"SYNC-NE:SWTOINT,SC,,,,,,,:\"SWITCH TO INTERNAL CLOCK\",TCC";

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
A 100.100 REPT EVT SYNCN
"SYNC-NE:SWTOINT,SC,,,,,,,:\"SWITCH TO INTERNAL CLOCK\",CTX-2500";

;

Table 17-19 REPT EVT SYNCN Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.1  ALL" section on page 25-1.

Y

Y

Y

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 on page 26-1 for a list of conditions.

Y

Y

Y

<CONDEFF>

(Optional) The effect of the event on the condition of the NE. The parameter type is COND_EFF, which is the state of the condition upon the affected unit.

Y

Y

Y

•CL

Standing condition cleared

Y

Y

Y

•SC

Standing condition raised

Y

Y

Y

•TC

Transient condition

Y

Y

Y

<DESC>

(Optional) Condition description.

Y

Y

Y

<AIDDET>

(Optional) AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed. The parameter type is EQPT_TYPE, which is the type of equipment being provisioned into a slot.

Y

Y

Y

•32DMX-L

32-channel demultiplexer for L-band

Y

Y

Y

•32WSS-L

32-channel wavelength switch selector for L-band

Y

Y

Y

•AD-1B

OADM 1-Band Filter

Y

Y

Y

•AD-1C

OADM 1-Channel Filter

Y

Y

Y

•AD-2C

OADM 2-Channel Filter

Y

Y

Y

•AD-4B

OADM 4-Bans Filter

Y

Y

Y

•AD-4C

OADM 4-Channel Filter

Y

Y

Y

•AICI

AIC-I card

Y

Y

Y

•AIP

Alarm Indication Panel

Y

Y

Y

•ALM-PWR

Alarm Power

Y

Y

Y

•ASAP-4

ASAP carrier card with four PIM slots

Y

Y

Y

•BP

The backplane of the NE

Y

Y

Y

•CE-100T-8

8-port 100T card

Y

Y

Y

•CE-1000-4

4-port GIGE mapper card

Y

Y

Y

•CRFT-TMG

Craft Timing

Y

Y

N

•DCC

Data Communications Channel

Y

Y

N

•DMX-32

Optical DMX 32 Channels

Y

Y

N

•DS3i-N-12

DS3i-N-12 card

Y

Y

N

•E1-21-DS3-E3-3

ONS 15310 MA SDH E1,E3, DS3

N

N

Y

•E1-63-DS3-E3-3

ONS 15310 MA SDH E1,E3, DS3

N

N

Y

•E1

E1 card

Y

Y

Y

•E1-42

42-port E1 card

Y

Y

N

•E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

Y

Y

N

•E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

Y

Y

N

•E1N

E1N card

Y

Y

N

•E3

E3 card

Y

Y

Y

•FILLER_CARD

Filler card

Y

Y

Y

•FMEC-SMZ-E1

FMEC card corresponding to E1 card

Y

Y

N

•FMEC-SMZ-E3

FMEC card corresponding to E3 card

Y

Y

N

•FTA

Fan Tray of the NE

Y

Y

N

•FTA1

Fan Tray 1 of the NE

Y

Y

N

•FTA2

Fan Tray 2 of the NE

Y

Y

N

•G1K-4

G1K-4 card

Y

Y

N

•MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

Y

Y

N

•ML100X-8

8-port 100T card with optical interface

Y

Y

N

•MMU

Multiring mesh upgrade unit

Y

Y

N

•MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

Y

Y

N

•MUX-32

Optical MUX 32 Channels

Y

Y

N

•MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

Y

Y

N

•MXP-MR-10DME

10 Gbps datamux with enhanced FEC

Y

Y

N

•OPT-AMP-L

Optical preamplifier for L-band

Y

Y

N

•OPT-BST

Optical booster amplifier

Y

Y

N

•OPT-BST-L

Optical booster for L-band

Y

Y

N

•OPT-PRE

Optical Preamplifier

Y

Y

N

•OPT-RAMP-C

Raman pump amplifier C-band

Y

N

N

•OSC-CSM

Optical Service Channel with Combiner/Separator Module

Y

Y

N

•OSCM

Optical Service Channel Module

Y

Y

N

•OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

Y

N

N

•PIM-4

Pluggable interface module with 4 PPM slots

Y

Y

N

•PPM-1

Pluggable port module with 1-port SFP module

Y

Y

N

•PSM

Protection unit

Y

N

N

•SHELF

Shelf entity

Y

Y

N

•STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

Y

Y

Y

•STM4-4

A four port STM4 card

Y

Y

N

•STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM4-SR-1

An interface card that supports one short range STM4 (622 Mbps) optical facilities

Y

Y

N

•STM64-4

A four-port STM64 card

Y

Y

N

•STM64-LR-1

An interface card that supports one or more STM64 optical facilities

Y

Y

N

•STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

Y

Y

Y

•STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

Y

Y

N

•STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) ATM optical fibers

Y

Y

N

•STM1IR-STM1SH-
1310-8

An STM1 card which has 8 ports over the lower speed slot of the ONS 15454 SDH with XC-VXL-10G/XC-VXL-2.5G

Y

Y

N

•STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) POS optical facilities

Y

Y

N

•STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

Y

Y

Y

•STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

Y

Y

N

•STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

Y

Y

N

•STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

Y

Y

N

•STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

Y

Y

N

•TCC

Timing, Communications, and Control card

Y

Y

Y

•TXP-MR-10G

10G Multirate Transponder card

Y

Y

Y

•TXP-MR-2.5G

Multirate 2.5G Unprotected

Y

Y

Y

•TXPP-MR-2.5G

Multirate 2.5G Protected

Y

Y

Y

•UNKNOWN

Unknown equipment type

Y

Y

Y

•UNPROVISIONED

Unprovisioned equipment type

Y

Y

Y

•XC-VXC-10G

XC-VXC-10G cross-connect card

Y

Y

Y

•XCVXL-10G

XC-VXL-10G cross-connect card

Y

Y

Y

•XCVXL-2.5G

XC-VXL-2.5G cross-connect card

Y

Y

Y


17.20  REPT PM <MOD2>

The Report Performance Monitoring for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1, E3, E4, ESCON, ETRCLO, ETH, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, STS36C, VC4, VC416C, VC42C, VC43C, or VC12 (REPT PM <MOD2>) message reports autonomous monitoring statistics as a result of the schedule created by SCHED-PMREPT.

Note The E1, E3, E4, ETH, FSTE, STM1, STM4, STM16, POS, T3, VC3, VC44C, VC48C, VC4, VC416C, VC42C, VC43C, and VC12 are the only modifiers supported on the Cisco ONS 15310 MA SDH platform.

Usage Guidelines

See Table 27-1 on page 27-1 for supported modifiers by platform.

Note Autonomous performance monitoring (Auto PM) report will have all PM paths reported without any filtering. If a particular parameter is not applicable to that card or circuit, then the value of MONVAL and VLDTY will be NA.

Category

Performance

Security

Retrieve

Output Format

SID DATE TIME
A ATAG REPT PM <MOD2>
"<AID>:<MONTYPE>,<MONVAL>,<VLDTY>,<lSTM>,<DIRN>,<TMPER>,<MONDAT>,
<MONTM>"
;

Output Example

TID-000 1998-06-20 14:30:00
A 100 REPT PM 10GFC
"FAC-3-1:CVL,10,PRTL,NEND,BTH,15-MIN,05-25,14-46"
;

Cisco ONS 15310 MA SDH

TID-000 1998-06-20 14:30:00
A 100 REPT PM E3
"E3-5-1:CVL,10,PRTL,NEND,BTH,15-MIN,05-25,14-46"
;

Table 17-20 REPT PM <MOD2> Command - Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "25.1  ALL" section on page 25-1.

Y

Y

Y

<MONTYPE>

Monitored type. The parameter type is ALL_MONTYPE, which is the monitoring type list.

Y

Y

Y

•AISSP

Alarm Indication Signal Seconds—Path

Y

Y

Y

•ALL

All possible values

Y

Y

Y

•BBEP

SDH Background Block Errors Path

Y

Y

Y

•BBE-PM

OTN—Background Block Errors—Path Monitor Point

Y

Y

Y

•BBER

SDH Background Block Error Ratio

Y

Y

Y

•BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as one tenth of a percentage.

Y

Y

Y

•BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as one tenth of a percentage

Y

Y

Y

•BBE-SM

OTN—Background Block Errors—Section Monitor Point

Y

Y

Y

•BIEC

FEC—Bit Errors Corrected

Y

Y

Y

•CGV

8B10B—Code Group Violations

Y

Y

Y

•