Table Of Contents
Change Port Settings
Before You Begin
NTP-B88 Modify Line Settings and PM Parameter Thresholds for Electrical Ports
NTP-B89 Modify Line Settings and PM Parameter Thresholds for Optical Ports
NTP-B208 Change Card Service State
Change Port Settings
This chapter explains how to change transmission settings on electrical and optical ports for a Cisco ONS 15327.
Before You Begin
Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15327 Troubleshooting Guide as necessary.
Caution 
Changing card or port settings can be service-affecting. You should make all changes during a scheduled maintenance window.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. B88 Modify Line Settings and PM Parameter Thresholds for Electrical Ports—Complete as needed.
2. B89 Modify Line Settings and PM Parameter Thresholds for Optical Ports—Complete as needed.
3. B208 Change Card Service State—Complete as needed.
NTP-B88 Modify Line Settings and PM Parameter Thresholds for Electrical Ports
Purpose
|
This procedure changes the line and threshold settings for electrical ports.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-B60 Log into CTC" task on page 16-58 at the node where you want to change the card/port settings. If you are already logged in, continue with Step 2.
Step 2 Per site practice, complete the "NTP-B108 Back Up the Database" procedure on page 14-3 to preserve the existing database.
Step 3 Perform either of the following tasks as needed:
•DLP-B165 Change Line and Threshold Settings for the DS-1 Ports, page 17-51
•DLP-B166 Change Line and Threshold Settings for the DS-3 Ports, page 17-56
Step 4 When you are finished changing the port settings, complete the "NTP-B108 Back Up the Database" procedure on page 14-3 per site practice.
Stop. You have completed this procedure.
NTP-B89 Modify Line Settings and PM Parameter Thresholds for Optical Ports
Purpose
|
This procedure changes the line and threshold settings for optical card and port performance monitoring.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
NTP-B218 Install the Optical and Ethernet Cards, page 1-11
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-B60 Log into CTC" task on page 16-58 at the node where you want to change the card settings. If you are already logged in, continue with Step 2.
Step 2 Per site practice, complete the "NTP-B108 Back Up the Database" procedure on page 14-3 to preserve the existing database.
Step 3 Perform any of the following tasks as needed:
•DLP-B170 Change Line Settings for OC-N Cards, page 17-60
•DLP-B171 Change SONET Threshold Settings for OC-N Cards, page 17-62
•DLP-B172 Change an Optical Port to SDH, page 17-64
Step 4 Per site practice, complete the "NTP-B108 Back Up the Database" procedure on page 14-3.
Stop. You have completed this procedure.
NTP-B208 Change Card Service State
Purpose
|
This procedure changes the card service state.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
Chapter 1, "Install Hardware"
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-B60 Log into CTC" task on page 16-58 at the node where you want to change card service state.
Step 2 Click the Inventory tab.
Step 3 Click Admin State for the card you want to change, and choose an Admin state from the drop-down list: IS (In-Service) or OOS,MT (Out-of-Service,Maintenance).
Step 4 Click Apply.
Step 5 If an error message opens indicating that the card state cannot be changed from its current state, click OK.
Table 9-1 lists possible card service state transitions based on the Admin State chosen. For more information about the enhanced state model and card state transitions, refer to the "Administrative and Service States" appendix of the Cisco ONS 15327 Reference Manual.
Table 9-1 Cisco ONS 15327 Card State Transitions
Admin State
|
Original Service State
|
Next Service State
|
IS
|
OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous Management,Maintenance and Unequipped)
|
OOS-AU,UEQ
(Out-of-Service & Autonomous,Unequipped)
|
IS
|
OOS-AUMA,MEA & MT
(Out-of-Service and Autonomous Management,Mismatched Equipment and Maintenance)
|
OOS-AU,MEA
(Out-of-Service and Autonomous,Mismatched Equipment)
|
IS
|
OOS-MA,MT
(Out-of-Service and Management,Maintenance)
|
IS-NR
(In-Service and Normal)
|
OOS,MT
|
OOS-AU,MEA
(Out-of-Service and Autonomous,Mismatched Equipment)
|
OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous Management,Maintenance and Unequipped)
|
OOS,MT
|
OOS-AU,AINS & MEA
(Out-of-Service and Autonomous,Auto In-Service and Mismatched Equipment)
|
OOS-AUMA,MEA & MT
(Out-of-Service and Autonomous Management,Mismatched Equipment and Maintenance)
|
OOS,MT
|
OOS-AU,UEQ
(Out-of-Service and Autonomous,Unequipped)
|
OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous Management,Maintenance and Unequipped)
|
OOS,MT
|
IS-NR
(In-Service and Normal)
|
OOS-MA,MT
(Out-of-Service and Management,Maintenance)
|
Stop. You have completed this procedure.
