Table Of Contents
Change Card Settings
Before You Begin
NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards
NTP-D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards
NTP-D118 Modify Alarm Interface Controller-International Settings
NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection
NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards
NTP-D307 Change Card Service State
Change Card Settings
This chapter explains how to change line and threshold settings on Cisco ONS 15454 SDH cards.
Before You Begin
Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide as necessary.
Caution 
Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards—As needed, complete this procedure to change line and threshold settings for all electrical cards (E1-N-14, E1-42, E3-12, DS3i-N-12, and STM1E-12).
2. D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards—As needed, complete this procedure to change line and threshold settings for all optical (STM-N) cards.
3. D118 Modify Alarm Interface Controller-International Settings—As needed, complete this procedure to change external alarms and controls and/or orderwire settings.
4. D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection—As needed, complete this procedure to change the protection type on E-1 or DS-3 cards.
5. D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards—As needed, complete this procedure to change the FC_MR-4 card port and threshold settings.
6. D307 Change Card Service State—As needed, complete this procedure to change card service state.
NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards
Purpose
|
This procedure changes the line settings and performance monitoring (PM) parameter thresholds for electrical cards.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
NTP-D17 Install the Electrical Cards, page 2-9
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the electrical card settings. If you are already logged in, proceed to Step 2.
Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4 to preserve the existing database.
Step 3 Perform any of the following tasks as needed:
•DLP-D339 Change Line and Threshold Settings for E1-N-14 or E1-42 Cards, page 20-39
•DLP-D340 Change Line and Threshold Settings for the E3-12 Cards, page 20-44
•DLP-D341 Change Line and Threshold Settings for the DS3i-N-12 Cards, page 20-47
•DLP-D342 Change Line and Threshold Settings for the STM1E-12 Card, page 20-52
Step 4 When you are finished changing the card settings, complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Stop. You have completed this procedure.
NTP-D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards
Purpose
|
This procedure changes the line settings and the PM parameter thresholds for optical cards.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
NTP-D16 Install the STM-N Cards, page 2-7
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the STM-N card settings. If you are already logged in, proceed to Step 2.
Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Step 3 Perform any of the following tasks as needed:
•DLP-D170 Change Line Settings for STM-N Cards, page 18-28
•DLP-D343 Change SDH Threshold Settings for STM-N Cards, page 20-55
Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Stop. You have completed this procedure.
NTP-D118 Modify Alarm Interface Controller-International Settings
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the AIC-I card settings. If you are already logged in, proceed to Step 2.
Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Step 3 Perform any of the following tasks as needed:
•DLP-D208 Change External Alarms Using the AIC-I Card, page 19-5
•DLP-D209 Change External Controls Using the AIC-I Card, page 19-6
•DLP-D210 Change AIC-I Card Orderwire Settings, page 19-6
Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Stop. You have completed this procedure.
NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection
Purpose
|
This task converts E1-N-14 and DS3i-N-12 protect cards from 1:1 to 1:N protection.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
DLP-D71 Create a 1:1 Protection Group, page 17-61
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to convert the E1-N-14 and DS3i-N-12 cards from 1:1. If you are already logged in, proceed to Step 2.
Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Step 3 Perform any of the following tasks as needed:
•DLP-D176 Convert E1-N-14 Cards From 1:1 to 1:N Protection, page 18-31
•DLP-D177 Convert DS3i-N-12 Cards From 1:1 to 1:N Protection, page 18-32
Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Stop. You have completed this procedure.
NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards
Purpose
|
This procedure changes the line settings and PM parameter thresholds for FC_MR-4 cards.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
NTP-D286 Install the FC_MR-4 Cards, page 2-12
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the OC-N card settings. If you are already logged in, proceed to Step 2.
Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Step 3 Perform any of the following tasks as needed:
•DLP-D354 Change General Port Settings for the FC_MR-4 Card, page 20-61
•DLP-D355 Change Distance Extension Port Settings for the FC_MR-4 Card, page 20-63
•DLP-D356 Change Enhanced FC/FICON Port Settings for the FC_MR-4 Card, page 20-64
•DLP-D465 Create FC_MR-4 RMON Alarm Thresholds, page 21-45
•DLP-D466 Delete FC_MR-4 RMON Alarm Thresholds, page 21-49
Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.
Stop. You have completed this procedure.
NTP-D307 Change Card Service State
Purpose
|
This procedure changes card service state.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
Chapter 2, "Install Cards and Fiber-Optic Cable"
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the card service state.
Step 2 Click the Inventory tab.
Step 3 Click Admin State for the card you want to change, and choose an Admin state from the drop-down list: Unlocked or Locked,maintenance.
Step 4 Click Apply.
Step 5 If an error message opens indicating that the card state cannot be changed from its current state, click OK.
Table 11-1 lists possible card service state transitions based on the Admin State chosen. For more information about the enhanced state model and card state transitions, refer to the "Administrative and Service States" appendix of the Cisco ONS 15454 SDH Reference Manual.
Table 11-1 Cisco ONS 15454 SDH Card State Transitions
Admin State
|
Original Service State
|
Next Service State
|
Unlocked
|
Locked-disabled,maintenance & notInstalled
|
Unlocked-disabled,notInstalled
|
Unlocked
|
Locked-disabled,mismatchOfEquipment & maintenance
|
Unlocked-disabled,mismatchOfEquipment
|
Unlocked
|
Locked-enabled,maintenance
|
Unlocked-enabled
|
Locked, maintenance
|
Unlocked-disabled,mismatchOfEquipment
|
Locked-disabled,maintenance & notInstalled
|
Locked, maintenance
|
Unlocked-disabled,automaticInService & notInstalled
|
Locked-disabled,maintenance & notInstalled
|
Locked, maintenance
|
Unlocked-disabled,automaticInService & mismatchOfEquipment
|
Locked-disabled,mismatchOfEquipment & maintenance
|
Locked,maintenance
|
Unlocked-disabled,notInstalled
|
Locked-disabled,maintenance & notInstalled
|
Locked,maintenance
|
Unlocked-enabled
|
Locked-enabled,maintenance
|
Stop. You have completed this procedure.
Feedback
