Guest

Cisco ONS 15454 Series Multiservice Provisioning Platforms

Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.6

 Feedback

Table Of Contents

Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.6

Cross Connections

DWDM (Cisco ONS 15454 only)

Environment

Environment Alarms and Controls

Equipment

Fault

File Transfer

IOS

Log

Network

Paths

Performance

Ports

Security

SONET Line Protection

Switch

Synchronization

System

Test Access

Testing

Trace

UCP (Cisco ONS 15454 only)

Path Protection Switching

VCAT


Quick Reference

Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.6



Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.


This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 and the Cisco ONS 15327, Release 4.6. Refer to the Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Guide, Release 4.6 for a complete description of TL1 commands.

TL1 commands conform to the following syntax:
a:b:c:d:e: ...z;
where:
"a" is the Command Code
"b" is the Target Identifier (TID)
"c" is the Access Identifier (AID) or the User Identifier (UID)
"d" is the Correlation Tag (CTAG)
"e: ...z;" are other positions required for various commands
The TID, AID, and CTAG route and control the TL1 command.
Other parameters provide additional information required to complete the action requested by the commanBLSR

Table 1 BLSR 

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];
Deletes the BLSR of the NE

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>][:];
Edits the BLSR attributes

ENT-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>,
MODE=<MODE>,[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,]
[SRVTM=<SRVTM>,]EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>,
[EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>];
Creates either a two-fiber or four-fiber BLSR

EX-SW-<OCN_BLSR>:[<TID>]:<AID>:<CTAG>::,[<SWITCHTYPE>][,<DIRECTION>];
Exercises the algorithm for switching from a working facility to a protection facility without actually performing a switch.

RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];
Retrieves all of the BLSR information of the network element (NE)
Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>]::[RINGID=<RINGID>,][NODEID=<NODEID>,][MODE=<MODE>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>,]
[EASTWORK=<EASTWORK>,][WESTWORK=<WESTWORK>,][EASTPROT=<EASTPROT>,]
[WESTPROT=<WESTPROT>]"
;

RTRV-TRC-<OCN_BLSR>:[<TID>]:<AID>:<CTAG>;
Retrieves the valid J1 expected trace string, received trace string, trace mode, C2 byte and STS bandwidth of the OCN port if the port has a BLSR.
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][EXPTRC=<EXPTRC>,][INCTRC=<INCTRC>,]
[TRCMODE=<TRCMODE>,][C2=<C2>]"
;


1 Cross Connections

Table 2 Cross Connections 

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::];
Deletes a cross-connection between STS or VT paths

ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>,]
[REMOVE=<REMOVE>]:[<PST>],[<SST>];
Edits the state of an STS or VT cross-connection

ENT-CRS-<PATH>:[<TID>]:<AID>,<DST>:<CTAG>::[<CCT>]::[<PST>],[<SST>];
Creates an STS or VT cross-connection with cross-connection types (CCT)

RTRV-CRS:[<TID>]:<AID>:<CTAG>:::[CRSTYPE=<CRSTYPE>][:];
Retrieves all the cross-connections based on the required CRSTYPE (for all STS connections)
Output format:

SID DATE TIME
M CTAG COMPLD
"<CROSSCONNECTID>,<CROSSCONNECTID1>:<CCT>,<MOD>::<PST>,[<SST>]"
;

RTRV-CRS-<PATH>:[<TID>]:<SRC>:<CTAG>[::::];
Retrieves any connections associated with the entered AID(s) or AID range
Output format:

SID DATE TIME
M CTAG COMPLD
"<CROSSCONNECTID>,<CROSSCONNECTID1>:<CCT>,<MOD>::<PST>,[<SST>]"
;


2 DWDM (Cisco ONS 15454 only)

Table 3 DWDM (Cisco ONS 15454 only) 

DLT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>[:::];
Deletes Y cable protection on client facilities

DLT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>;
Deletes an optical link between two optical connection points.

DLT-OSC:[<TID>]:<AID>:<CTAG>;
Deletes the OSC group of the NE

DLT-WLEN:[<TID>]:<AID>:<CTAG>[:::CMDMDE=<CMDMDE>];
Deletes the provisioned wavelength (WLEN)

ED-CLNT:[<TID>]:<AID>:<CTAG>:::[NAME=<PORTNAME>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>,][COMM=<COMM>,][MACADDR=<MACADDR>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][RLASER=<RLASER>,][SOAK=<SOAK>,][OSPF=<OSPF>]:[<PST>],[<SST>];
Edits client facility attributes

ED-DWDM:[<TID>]:<AID>:<CTAG>:::[PEERID=<PEERID>,][NAME=<NAME>,]
[TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,][PWL=<PWL>];
Edits an already pre-provisioned/provisioned MXP_2.5G_10G and TXP_MR_10G card

ED-FFP-CLNT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];
Edits a Y cable protection group on client facilities

ED-FFP-OCH::[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];
Edits the provisioning for the default protection group on the DWDM port of a TXP_MR_2.5G or TXPP_MR_2.5G card

ED-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>::::<PST>,[<SST>];
Edits an optical link

ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPWLEN=<EXPWLEN>,]
[VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,][SDBER=<SDBER>,]
[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,]
[COMM=<COMM>,][GCCRATE=<GCCRATE>,][OSDBER=<OSDBER>,][DWRAP=<DWRAP>,]
[FEC=<FEC>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,]
[SENDDUS=<SENDDUS>,][RLASER=<RLASER>,][SOAK=<SOAK>,][OSPF=<OSPF>]:[<PST>],
[<SST>];
Edits the attributes (service parameters) and state of an OCH facility

ED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPBAND=<EXPBAND>,]
[VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>]:[<PST>],[<SST>];
Edits the attributes (service parameters) and state of an OMS facility (R4.5 only)

ED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>];
Edits the OSC (Optical Service Channel) group attributes

ED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,][CALTILT=<CALTILT>,][OSRI=<OSRI>,]
[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,]
[EXPGAIN=<EXPGAIN>]:[<PST>],[<SST>];
Edits the attributes (service parameters) and state of an OTS facility

ED-TRC-CLNT:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,]TRCLEVEL=<TRCLEVEL>,[TRCFORMAT=<TRCFORMAT>][:];
Edits trace-related attributes on client facilities

ED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,][TRCLEVEL=<TRCLEVEL>,][TRCFORMAT=<TRCFORMAT>][:];
Edits trace-related optical channel facilities

ED-WDMANS:[<TID>]:<AID>:<CTAG>:::[POWER-IN=<POWERIN>,]
[POWER-OUT=<POWEROUT>,][POWER-EXP=<POWEREXP>,]
[POWER-DROP=<POWERDROP>,][SYS-TYPE=<SYSTYPE>,][RING-TYPE=<RINGTYPE>];
Edits the optical node setup (AONS) application attributes

ED-WLEN:[<TID>]:<AID>:<CTAG>:::[SIZE=<SIZE>]:[<PST>],[<SST>];
Edits wavelength (WLEN) provisioning

ENT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>:::[PROTTYPE=<PROTTYPE>,]
[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];
Creates Y cable protection on client facilities

ENT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>::::<PST>,[<SST>];
Creates an optical link between two optical connection points

ENT-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>,
[EAST=<EAST>,][WEST=<WEST>];
Creates the OSC (optical service channel) group of the NE

ENT-WLEN:[<TID>]:<AID>:<CTAG>:::[SIZE=<SIZE>]:[<PST>],[<SST>];
Allocates a wavelength

OPR-LASER-OTS:[<TID>]:<AID>:<CTAG>;
Instructs a laser to be switched on

OPR-LNK:[<TID>]::<CTAG>;
Permits the optical link application inside the NE to calculate all the automatic optical links between end points which can be univocally identified by the NE

OPR-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>::<SC>[:];
Operates a Y cable protection switch request

OPR-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>[::];
Performs a protection switch on the trunk port of a TXPP_MR_2.5G card

OPR-WDMANS:[<TID>]::<CTAG>;
Operates the Automatic Optical Node Setup (AONS) application inside the NE to force a recompute of the value to be assigned to all VOAs representing the Optical Path inside the node

RLS-LASER-OTS:[<TID>]:<AID>:<CTAG>;
Instructs a laser to be switched off

RLS-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::];
Releases a Y cable protection switch on client facilities

RLS-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>[::];
Performs a protection switch on the trunk port of a TXPP_MR_2.5G card

RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<ALMTHR>[,,::];
Retrieves the alarm threshold values
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>"
;

RTRV-CLNT:[<TID>]:<AID>:<CTAG>;
Retrieves client facility attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],<STATUS>:[NAME=<PORTNAME>,][COMM=<COMM>,]
[SFBER=<SFBER>,][SDBER=<SDBER>,][ALSMODE=<ALSMODE>,]
[ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,][SYNCMSG=<SYNCMSG>,]
[SENDDUS=<SENDDUS>,][LSRSTAT=<LSRSTAT>,][CLEI=<CLEI>,][PN=<PARTNUM>,]
[SN=<SERIALNUM>,][VENDORREV=<VENDORREV>,][PLGTYPE=<PLGTYPE>,]
[MACADDR=<MACADDR>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,]
[OSPF=<OSPF>]:<PST>,[<SST>]"
;

RTRV-DWDM:[<TID>]:<AID>:<CTAG>;
Retrieves DWDM card-level attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<EQPTTYPE>,<EQUIP>,,[<STATUS>]:[PEERID=<PEERID>,][NAME=<NAME>,]
[TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,][CARDNAME=<CARDNAME>,]
[PWL=<PWL>,][TWL1=<TWL>,][TWL2=<TWL1>,][TWL3=<TWL2>,][TWL4=<TWL3>]:
[<PST>],[<SST>]"
;

RTRV-FFP-CLNT:[<TID>]:<AID>:<CTAG>[::::];
Retrieves Y cable protection on client facilities
Output format:

SID DATE TIME
M CTAG COMPLD
"<WORKAID>,<PROTAID>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]"
;

RTRV-FFP-OCH:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the protection group information for the TXP_MR_2.5G and TXPP_MR_2.5G trunk port
Output format:

SID DATE TIME
M CTAG COMPLD
"<WORK>,<PROTECT>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]"
;

RTRV-LNK:[<TID>]::<CTAG>;
Retrieves all the optical links created in the NE
Output format:

SID DATE TIME
M CTAG COMPLD
"<FROM>,<TO>::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,][RDIRN=<RDIRN>,]
[BAND=<BAND>,][WLEN=<WLEN>]:<PST>,[<SST>]"
;

RTRV-LNK-<MOD2O>:[<TID>]:<AID>:<CTAG>:::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,]
[RDIRN=<RDIRN>];
Retrieves any optical link associated with the entered AIDs or AID range
Output format:

SID DATE TIME
M CTAG COMPLD
"<FROM>,<TO>::[OLNKT=<OPTICALLINKTYPE>,][CTYPE=<CREATIONTYPE>,]
[RDIRN=<RDIRN>,][BAND=<BAND>,][WLEN=<WLEN>]:<PST>,[<SST>]"

;

RTRV-NE-WDMANS:[<TID>]::<CTAG>;
Retrieves the optical nodes setup (WDMANS) application ports involved in node setup regulation
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[REGULATED=<REGULATED>]"
;

RTRV-OCH:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (service parameters) and state of an OCH facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[RDIRN=<RDIRN>,][OPTYPE=<OPTICALPORTTYPE>,]
[OPWR=<POWER>,][EXPWLEN=<EXPWLEN>,][ACTWLEN=<ACTWLEN>,]
[ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,]
[VOAREFPWR=<VOAREFPWR>,][REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,][SDBER=<SDBER>,]
[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,]
[COMM=<COMM>,][GCCRATE=<GCCRATE>,][DWRAP=<DWRAP>,][FEC=<FEC>,]
[OSFBER=<OSFBER>,][OSDBER=<OSDBER>,][MACADDR=<MACADDR>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][LSRSTAT=<LSRSTAT>,]
[SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][OSPF=<OSPF>]:<PST>,[<SST>]"
;

RTRV-OMS:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (service parameters) and state of an OMS facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,]
EXPBAND=<EXPBAND>,[ACTBAND=<ACTBAND>,][ILOSS=<ILOSS>,]
[VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,]
[VOAREFATTN=<VOAREFATTN>,][VOAREFPWR=<VOAREFPWR>,]
[REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][CHPOWER=<CHPOWER>]:<PST>,
[<SST>]"
;

RTRV-OSC:[<TID>]:<AID>:<CTAG>;
Retrieves all of the OSC (optical service channel) information of the NE
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[RINGID=<RINGID>,][NODEID=<NODEID>,][EAST=<EAST>,][WEST=<WEST>]"
;

RTRV-OTS:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (service parameters) and state of an OTS facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,]
[ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,]
[VOAREFPWR=<VOAREFPWR>,][LASERST=<LASERST>,][OSRI=<OSRI>,]
[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,]
[AMPLMODE=<AMPLMODE>,][GAIN=<GAIN>,][EXPGAIN=<EXPGAIN>,]
[REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][REFTILT=<REFTILT>,]
[CALTILT=<CALTILT>,][DCULOSS=<DCULOSS>,][AWGST=<AWGST>,]
[HEATST=<HEATST>]:<PST>,[<SST>]"
;

RTRV-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::::];
Retrieves protection switch status of client facilities
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<SC>,[<SWITCHTYPE>]"
;

RTRV-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>;
Retrieves protection switch status of a TXPP_MR_2.5G card
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<SW>,<SWTYPE>"
;

RTRV-TRC-CLNT:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::];
Retrieves the SONET J0 Section sent trace string, expected trace string, received trace string, trace mode, and the trace level for the client facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]"
;

RTRV-TRC-OCH:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::];
Retrieves the sent trace string, expected trace string, received trace string, trace mode, and the trace level for the SONET J0 Section, the TTI PATH and SECTION monitoring levels of the DWDM facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<CHANNEL>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]"
;

RTRV-WDMANS:[<TID>]:<AID>:<CTAG>;
Retrieves the automatic optical node setup (AONS) application attributes
Output format:

SID DATE TIME
M CTAG COMPLD

"<AID>::[POWER-IN=<POWERIN>,][POWER-OUT=<POWEROUT>,]
[POWER-EXP=<POWEREXP>,][POWER-DROP=<POWERDROP>,][SYS-TYPE=<SYSTYPE>,]
[APC-ENABLE=<APCENABLE>,][RING-TYPE=<RINGTYPE>]"
;

RTRV-WLEN:[<TID>]:<AID>:<CTAG>;
Retrieves the wavelength provisioning information
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[SIZE=<SIZE>]:[<PST>],[<SST>]"
;

SET-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<CONDTYPE>,<THLEV>[,,,];
Sets alarm thresholds on MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, TXPP_MR_2.5G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, MD-4, MUX-32, DMX-32, AD-1C, AD-2C, AD-4C, AD-1B, AD-4B facilities, ports and channels


3 Environment

Table 4 Environment 

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];
Retrieves attributes associated with an external control

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>]"
;

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];
Retrieves attributes associated with an environmental alarm

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]"
;

SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];
Sets attributes associated with an external control

SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::<NTFCNCDE>,<ALMTYPE>,<ALMMSG>;
Sets attributes associated with an external control


4 Environment Alarms and Controls

Table 5 Environment Alarms and Controls 

OPR-ACO-ALL:[<TID>]::<CTAG>;
Operates the cut-off of the office audible alarm indications without changing the local alarm indications

OPR-EXT-CONT:[<TID>]:<AID>:<CTAG>::[<CONTTYPE>],[<DURATION>];
Operates an external control and closes the external control contact

REPT ALM ENV
Reports a user-defined condition on an environmental alarm input

REPT EVT ENV
Reports a non-alarmed event against an environment alarm input

RLS-EXT-CONT:[<TID>]:<AID>:<CTAG>[::,];
Releases a forced contact state and returns the control of the contact to an automatic control state

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];
Retrieves the environmental alarms
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,,,[<DESC>]"
;

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>][,,,];
Retrieves the environmental conditions
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],,,,[<DESC>]"
;

RTRV-EXT-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];
Retrieves the control state of an external control
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>],<DUR>,[<CONTSTATE>]"
;


5 Equipment

Table 6 Equipment 

ALW-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::];
Allows automatic or manual switching on a duplex system containing duplexed or redundant equipment (Cisco ONS 15454 only)

ALW-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];
Allows automatic or manual switching of an equipment unit back to a protection status
(Cisco ONS 15454 only)

ALW-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];
Allows automatic or manual switching of an equipment unit back to a working status
(Cisco ONS 15454 only)

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::];
Deletes a card from the NE

ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,]
[PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>][:];
Edits the attributes for a given equipment slot in the NE

ENT-EQPT:[<TID>]:<AID>:<CTAG>::<AIDTYPE>:[PROTID=<PROTID>,]
[PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>][:];
Enters the card type and attributes for a given equipment slot in the NE

INH-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::];
Inhibits the automatic or manual switching on an NE containing duplex equipment
(Cisco ONS 15454 only)

INH-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];
Inhibits automatic or manual switching of an equipment unit to protection (Cisco ONS 15454 only)

INH-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];
Inhibits automatic or manual switching of an equipment unit back to the working unit
(Cisco ONS 15454 only)

REPT ALM EQPT
Reports an alarm condition against an equipment unit or slot

REPT EVT EQPT
Reports the occurrence of a non-alarmed event against an equipment unit or slot

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>][,,,];
Retrieves and sends the current status of alarm conditions associated with the equipment units
Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]"
;

RTRV-ALMTH-EQPT:[<TID>]::<CTAG>::<ALMTHR>[,,::];
Retrieves the alarm thresholds for the power level monitoring
Output format:

SID DATE TIME
M CTAG COMPLD
",<MOD2B>:<ALMTHR>,,,<DNFIELD>"
;

RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];
Retrieves the equipment conditions
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::];
Retrieves protection group information and status information for all cards
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>,]
[PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,]
[CARDNAME=<CARDNAME>,][IOSCFG=<IOSCFG>]:[<PST>],[<SST>]"
;

SW-DX-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>][,];
Switches an XC/XCVT/XC10G card with the mate card within the NE (Cisco ONS 15454 only)

SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<PROTID>],[<DIRN>];
Performs an equipment unit protection switch (Cisco ONS 15454 only)

SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>];
Switches the protected working unit back to the working unit (Cisco ONS 15454 only)


6 Fault

Table 7 Fault 

REPT ALM <MOD2ALM>
Reports an alarm condition against a facility or a path

REPT ALM COM
Reports an alarm condition when an AID cannot be given

REPT EVT <MOD2ALM>
Reports the occurrence of a non-alarmed event

REPT EVT COM
Reports a non-alarmed event against an NE when there is no AID associated with it

RTRV-ALM-ALL:[<TID>]::<CTAG>::[<NTFCNCDE>],[<CONDITION>],[<SRVEFF>][,,,];
Retrieves and sends the current status of all active alarm conditions
Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>],[<AIDDET>]"
;

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];
Retrieves the current standing condition and/or state associated with an entity
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-COND-ALL:[<TID>]::<CTAG>::[<TYPEREQ>][,,,];
Retrieves the current standing condition for all entities
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;


7 File Transfer

Table 8 File Transfer 

APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>];
Activates or reverts a software load during a software upgrade or downgrade

COPY-RFILE:[<TID>]:[<SRC>]:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>,]
[DEST=<DEST>,][OVWRT=<OVWRT>,][FTTD=<FTTD>];
Downloads a new software package from the location specified by the FTP URL

REPT EVT FXFR
Reports the FTP software download status of the start, completion and completed percentage


8 IOS

Table 9 IOS 

COPY-IOSCFG:[<TID>]:<AID>:<CTAG>::SRC=<SRC>,DEST=<DEST>;
Uploads startup IOS configuration files from the network to the node and downloads startup IOS configuration files from the node to the network (ML-series Ethernet cards) (Cisco ONS 15454 only)

REPT EVT IOSCFG
Reports the status of copying the IOS configuration file when the COPY-IOSCFG command is issued (Cisco ONS 15454 only)


9 Log

Table 10 Log 

ALW-MSG-DBCHG:[<TID>]::<CTAG>[::,,];
Enables REPT DBCHG

INH-MSG-DBCHG:[<TID>]::<CTAG>[::,,];
Disables REPT DBCHG

REPT DBCHG
Reports any changes on the NE that result from certain TL1 commands or an external event

RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>;
Retrieves the alarm log of the NE
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<ALMNUMBER>:CURRENT=<CURRENT>,[PREVIOUS=<PREVIOUS>,]
<CONDITION>,<SRVEFF>,[TIME=<OCRTIME>,][DATE=<OCRDAT>]:<ALMDESCR>"
;


10 Network

Table 11 Network 

RTRV-MAP-NETWORK:[<TID>]::<CTAG>;
Retrieves all the NE attributes which are reachable from the GNE
Output format:

SID DATE TIME
M CTAG COMPLD
"<IPADDR>,<NODENAME>,<PRODUCT>"
;

RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>;
Retrieves the IP address and node name of the NEs that have the DCC connection with this NE
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<IPADDR>,<NODENAME>"
;


11 Paths

Table 12 Paths 

ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SWPDIP=<SWPDIP>,]
[HOLDOFFTIMER=<HOLDOFFTIMER>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>]:[<PST>],[<SST>];
Edits the attributes associated with an STS or VT path

RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[BLSRPTHTYPE=<BLSRPTHTYPE>][:];
Retrieves the attributes associated with an STS or VT path
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,]
[EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,]
[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][UPSRPTHSTATE=<UPSRPTHSTATE>,][C2=<C2>,]
[BLSRPTHSTATE=<BLSRPTHSTATE>]:[<PST>],[<SST>]"
;

RTRV-STS:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes associated with an STS path based on the granularity level of NE/SLOT-specific STSs
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,]
[EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,]
[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][UPSRPTHSTATE=<UPSRPTHSTATE>,]
[C2=<C2>,][BLSRPTHSTATE=<BLSRPTHSTATE>]:[<PST>],[<SST>]"
;


12 Performance

Table 13 Performance 

ALW-PMREPT-ALL:[<TID>]::<CTAG>;
Resumes processing all the PM reports that are inhibited

INH-PMREPT-ALL:[<TID>]::<CTAG>;
Inhibits all scheduled PM reporting

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>],
[<TMPER>][,,];
Initializes the performance monitoring (PM) registers

REPT PM <MOD2>
Reports of performance monitoring statistics as a result of schedule created by SCHED-PMREPT

RTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],[<LOCN>],
[<DIRN>],[<TMPER>],[<DATE>],[<TIME>];
Retrieves the values of PM parameters for a specified card type
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],[<DIRN>],
[<TMPER>],[<MONDAT>],[<MONTM>]"
;

RTRV-PMMODE-<STS_PATH>:[<TID>]:<SRC>:<CTAG>::<LOCN>;
Retrieves the PM mode that has been previously set in the NE data collection
Output format:

SID DATE TIME
M CTAG COMPLD
"<CROSSCONNECTID>:[<LOCN>],<MODETYPE>"
;

RTRV-PMSCHED-<MOD2>:[<TID>]:<AID>:<CTAG>;
Retrieves the PM reporting schedule that was set for the NE by SCHED-PMREPT
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],,
[<MONLEV>],<LOCN>,,[<TMPER>],[<TMOFST>],[<INHMODE>]"
;

RTRV-PMSCHED-ALL:[<TID>]::<CTAG>;
Retrieves all the PM reporting schedules that were set for the NE by SCHED-PMREPT
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],,
[<MONLEV>],<LOCN>,,[<TMPER>],<TMOFST>,[<INHMODE>]"
;

RTRV-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<LOCN>],<TMPER>[::];
Retrieves the current threshold level of one or more monitored parameters
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,[<LOCN>],,<THLEV>,[<TMPER>]"
;

RTRV-TH-ALL:[<TID>]::<CTAG>::[<MONTYPE>],[<LOCATION>],[<TMPER>][::];
Retrieves the current threshold level of all monitored parameters
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>:<MONTYPE>,<LOCATION>,,<THLEV>,<TMPER>"
;

SCHED-PMREPT-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<REPTINVL>],
[<REPTSTATM>],[<NUMREPT>],,[<MONLEV>],[<LOCN>],,[<TMPER>],[<TMOFST>];
Schedules/reschedules the NE to report the performance monitoring data for a line facility or for an STS/VT path periodically, using an automatic REPT PM message

SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LOCN>],,[<TMPER>];
Sets the threshold for PM and sets the alarm thresholds for the MXP_2.5G_10G and TXP_MR_10G cards


13 Ports

Table 14 Ports 

ED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>,][AREA=<AREA>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][MUX=<MUX>,][SOAK=<SOAK>,][OSPF=<OSPF>,]
[LDCC=<LDCC>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>,][RLASER=<RLASER>]:[<PST>],[<SST>];
Edits the attributes and state of an OC-N facility

ED-DS1:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>];
Edits the test access attributes for DS1 access on a DS3XM card (Cisco ONS 15454 only)

ED-EC1:[<TID>]:<AID>:<CTAG>:::[PJMON=<PJMON>,][LBO=<LBO>,][SOAK=<SOAK>,]
[SFBER=<SFBER>,][SDBER=<SDBER>]:[<PST>],[<SST>];
Edits the attributes of an EC1 (Cisco ONS 15454 only)

ED-FC:[<TID>]:<AID>:<CTAG>:::[PAYLOAD=<PAYLOAD>,][LINKRCVRY=<LINKRCVRY>]:
[<PST>],[<SST>];

Edits the attributes related with the fiber channel facility

ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>,][FLOW=<FLOW>,]
[LOWMRK=<LOWMRK>,][HIWMRK=<HIWMRK>]:[<PST>],[<SST>];
Edits the attributes related to a G1000 port

ED-T1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,]
[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,][SFBER=<SFBER>,]
[SDBER=<SDBER>]:[<PST>],[<SST>];
Edits the attributes related a DS1/T1 port

ED-T3:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,]
[INHFELPBK=<INHFELPBK>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,]
[SFBER=<SFBER>,][SDBER=<SDBER>]:[<PST>],[<SST>];
Edits the attributes related to a DS3/T3 port

RMV-<MOD2_IO>:[<TID>]:<AID>:<CTAG>::[<CMDMODE>],[<PST>],[<SST>];
Removes a facility from service

RST-<MOD2_IO>:[<TID>]:<AID>:<CTAG>[::];
Provisions a facility in service

RTRV-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes and state of an OC-N facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>,][AREA=<AREA>,][TMGREF=<TMGREF>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][WVLEN=<WVLEN>,][RINGID=<RINGID>,]
[BLSRTYPE=<BLSRTYPE>,][MUX=<MUX>,][UNIC=<UNIC>,][CCID=<CCID>,]
[NBRIX=<NBRIX>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SSMRCV=<SSMRCV>,]
[OSPF=<OSPF>,][LDCC=<LDCC>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>]:<PST>,[<SST>]"
;

RTRV-DS1:[<TID>]:<SRC>:<CTAG>[::::];
Retrieves the test access attributes on a DS1 layer of DS3XM card (Cisco ONS 15454 only)
Output format:

SID DATE TIME
M CTAG COMPLD
"<DS1AID>::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>]"
;

RTRV-EC1:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the facility status of an EC1 card (Cisco ONS 15454 only)
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[PJMON=<PJMON>,][LBO=<LBO>,][RXEQUAL=<RXEQUAL>,][SOAK=<SOAK>,]
[SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,][SDBER=<SDBER>]:<PST>,[<SST>]"
;

RTRV-FC:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes related with the fiber channel port
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::PAYLOAD=<PAYLOAD>,LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>,
LINKRCVRY=<LINKRCVRY>:<PST>,[<SST>"
;

RTRV-FSTE:[<TID>]:<AID>:<CTAG>;
Retrieves the front end port information of the ML100T-12 Ethernet card
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,]
[MTU=<MTU>,][FLOWCTRL=<FLOWCTRL>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>]"
;

RTRV-G1000:[<TID>]:<AID>:<CTAG>;
Retrieves the G1000 facilities configuration
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[MFS=<MFS>,][FLOW=<FLOW>,][LAN=<LAN>,][OPTICS=<OPTICS>,]
[TRANS=<TRANS>,][TPORT=<TPORT>,][LOWMRK=<LOWMRK>,]
[HIWMRK=<HIWMRK>]:[<PST>],[<SST>]"
;

RTRV-GIGE:[<TID>]:<AID>:<CTAG>;
Retrieves the front end port information for the ML1000-2 Ethernet card
Output format:

SID DATE TIME
M CTAG COMPLD
"AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>,]
[FLOWCTRL=<FLOWCTRL>,][OPTICS=<OPTICS>,][DUPLEX=<DUPLEX>,]
[SPEED=<SPEED>]"
;

RTRV-POS:[<TID>]:<AID>:<CTAG>;
Retrieves the back end port information for the ML-series Ethernet cards when the back end port is working in POS mode
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>]"
;

RTRV-T1:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the DS1 facilities configuration
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][TACC=<TAP>,]
[TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,]
[SDBER=<SDBER>]:<PST>,[<SST>]"
;

RTRV-T3:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the facilities properties of a DS3 and DS3XM card
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,]
[INHFELPBK=<INHFELPBK>,][TACC=<TAP>,][TAPTYPE=<TAPTYPE>,]
[SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,]
[SDBER=<SDBER>]:<PST>,[<SST>]"
;


14 Security

Table 15 Security 

ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Sets up a session with the NE

ALW-MSG-SECU:[<TID>]::<CTAG>;
Allows REPT EVT SECU and REPT ALM SECU

ALW-USER-SECU:[<TID>]::<CTAG>::<UID>;
Enables a user ID that has been disabled (e.g., via the INH-USER-SECU command) so the user can establish a session with the NE

CANC
Reports the occurrence of a session timeout event
Output format:

SID DATE TIME
A ATAG CANC
"<UID>"
;

CANC-USER:[<TID>]:<USERID>:<CTAG>;
Logs a user out of an active session with the NE

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>;
Deletes a user; can only be performed by a Superuser

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;
Edits the command security level of a particular command

ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>;
Allows a user to change his or her own password

ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:];
Edits a user's privileges, password, or ID and can only be performed by a Superuser

ENT-USER-SECU:[<TID>]:<UID>:<CTAG>::<PID>,,<UAP>[:];
Adds a user account; can only be performed by a Superuser

INH-MSG-SECU:[<TID>]::<CTAG>;
Inhibits the REPT EVT SECU and REPT ALM SECU messages

INH-USER-SECU:[<TID>]::<CTAG>::<UID>;
Disables (without deleting) a userid, so the user is denied access to the NE

REPT ALM SECU
Reports the occurrence of an alarmed security event against the NE

REPT EVT SECU
Reports the occurrence of a non-alarmed security event against the NE

REPT EVT SESSION
Reports a non-alarmed event related to establishing a session with the NE

RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;
Retrieves the current command security level of the command specified in the AID field
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<CAP>"
;

RTRV-DFLT-SECU:[<TID>]:<AID>:<CTAG>;
Retrieves the system-wide default values associated with several security parameters
Output format:

SID DATE TIME
M CTAG COMPLD
"<NE>:PAGE=<PAGE>,PCND=<PCND>,MXINV=<MXINV>,DURAL=<DURAL>,
TMOUT=<TMOUT>,UOUT=<UOUT>,PFRCD=<PFRCD>,POLD=<POLD>,PINT=<PINT>,
LOGIN=<LOGIN>,PRIVLVL=<UAP>"
;

RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>;
Retrieves the security information of a specified user or list of users
Output format:

SID DATE TIME
M CTAG COMPLD
"<UID>:,<PRIVILEGE>:LOGGEDIN=<LOGGEDIN>,[NUMSESSIONS=<NUMSESS>,]
[LOCKEDOUT=<LOCKEDOUT>,][DISABLED=<DISABLED>]"
;

SET-ATTR-SECUDFLT:[<TID>]::<CTAG>::[PAGE=<PAGE>,][PCND=<PCND>,]
[MXINV=<MXINV>,][DURAL=<DURAL>,][TMOUT=<TMOUT>,][UOUT=<UOUT>,]
[PFRCD=<PFRCD>,][POLD=<POLD>,][PINT=<PINT>,][LOGIN=<LOGIN>,][PRIVLVL=<UAP>];
Sets the system-wide default values associated with several security parameters


15 SONET Line Protection

Table 16 SONET Line Protection 

DLT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::];
Deletes an OCN facility protection group in a 1+1 architecture

ED-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];
Edits the optical facility protection

ENT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>:::[PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];
Creates an optical 1+1 protection

OPR-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>::<SW>,[<SWITCHTYPE>]
[:<DIRECTION>];
Initiates a SONET line protection switch request

RLS-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::<DIRECTION>];
Releases a SONET line protection switch request

RTRV-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the optical facility protection information
Output format:

SID DATE TIME
M CTAG COMPLD
"<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,]
[PSDIRN=<PSDIRN>]"
;

RTRV-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the switching state of a SONET line specified in the AID
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<SC>,[<SWITCHTYPE>]"
;


16 Switch

Table 17 Switch 

RTRV-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>[::::];
Retrieves the switching state of a SONET path protection STS path specified in the AID
Output format:

SID DATE TIME
M CTAG COMPLD
"<CROSSCONNECTID>:<SC>,[<SWITCHTYPE>]"
;


17 Synchronization

Table 18 Synchronization 

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,]
[SYNCMSG=<SYNCMSG>,][AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,]
[IMPEDANCE=<IMPEDANCE>][:<PST>];
Edits the BITS reference attributes

ED-NE-SYNCN:[<TID>]::<CTAG>:::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,]
[QRES=<QRES>,][RVRTV=<RVRTV>,][RVTM=<RVTM>];
Edits the synchronization attributes of the NE

ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>,][SEC=<SEC>,][THIRD=<THIRD>][:];
Edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock

OPR-SYNCNSW:[<TID>]:[<AID>]:<CTAG>::<SWITCHTO>,[<SC>];
Initiates a switch to the reference specified by the synchronization reference number if the reference supplied is valid

REPT ALM BITS
Reports an alarm condition on a BITS facility

REPT ALM SYNCN
Reports an alarm condition against a synchronization reference

REPT EVT BITS
Reports the occurrence of a non-alarmed event against a BITS facility

REPT EVT SYNCN
Reports the occurrence of a non-alarmed event against a synchronization entity

RLS-SYNCNSW:[<TID>]:[<AID>]:<CTAG>;
Releases the previous synchronization reference provided by the OPR-SYNCNSW command

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,];
Retrieves and sends the current status of alarm conditions associated with the BITS facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]"
;

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>][,,,];
Retrieves and sends the current status of alarm conditions associated with a synchronization facility
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]"
;

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the BITS configuration command
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][SYNCMSG=<SYNCMSG>,]
[AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,][IMPEDANCE=<IMPEDANCE>]:
[<PST>]"
;

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];
Retrieves the standing condition on BITS
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];
Retrieves the synchronization condition
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],
[<OCRDAT>],[<OCRTM>],,,[<DESC>]"
;

RTRV-NE-SYNCN:[<TID>]::<CTAG>[::::];
Retrieves the synchronization attributes of the NE
Output format:

SID DATE TIME
M CTAG COMPLD
"::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,][QRES=<QRES>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>]"
;

RTRV-SYNCN:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<REF>,<REFVAL>,[<PROTECTSTATUS>],[<QREF>],[<STATUS>]"
;


18 System

Table 19 System 

ALW-MSG-ALL:[<TID>]::<CTAG>[::,,];
Allows REPT ALM and REPT EVT autonomous messages to be transmitted

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];
Edits the date and the time

ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>,][IPADDR=<IPADDR>,]
[IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,][IIOPPORT=<IIOPPORT>,][NTP=<NTP>]
[ETHIPADDR=<ETHIPADDR>,][ETHIPMASK=<ETHIPMASK>];
Edits the general node attributes of an NE

INH-MSG-ALL:[<TID>]::<CTAG>[::,,];
Inhibits REPT ALM and REPT EVT autonomous messages from being transmitted

INIT-SYS:[<TID>]:<AID>:<CTAG>[::];
Initializes the specified card and its associated subsystem(s)

RTRV-HDR:[<TID>]::<CTAG>;
Retrieves the header of a TL1 response message

RTRV-INV:[<TID>]:<AID>:<CTAG>[::::];
Retrieves a listing of the equipment inventory
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[PLUGTYPE=<PLUGTYPE>,][PN=<PN>,][HWREV=<HWREV>,]
[FWREV=<FWREV>,][SN=<SN>,][CLEI=<CLEI>,][TWL1=<TWL>,][TWL2=<TWL1>,]
[TWL3=<TWL2>,][TWL4=<TWL3>,][PLUGINVENDORID=<PLUGINVENDORID>,]
[PLUGINPN=<PLUGINPN>,][PLUGINHWREV=<PLUGINHWREV>,]
[PLUGINFWREV=<PLUGINFWREV>,][PLUGINSN=<PLUGINSN>,]
[ILOSSREF=<ILOSSREF>,][PID=<PID>,][VID=<VID>,][FPGA=<FPGA>]"
;

RTRV-NE-GEN:[<TID>]::<CTAG>;
Retrieves the general NE attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"[IPADDR=<IPADDR>,][IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,]
[IIOPPORT=<IIOPPORT>,][NTP=<NTP>,][ETHIPADDR=<ETHIPADDR>,]
[ETHIPMASK=<ETHIPMASK>,][NAME=<NAME>,][SWVER=<SWVER>,][LOAD=<LOAD>,]
[PROTSWVER=<PROTSWVER>,][PROTLOAD=<PROTLOAD>,][DEFDESC=<DEFDESC>,]
[PLATFORM=<PLATFORM>]"
;

RTRV-NE-PATH:[<TID>]::<CTAG>[::::];
Retrieves the general NE attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"[PDIP=<PDIP>]"
;

RTRV-TOD:[<TID>]::<CTAG>;
Retrieves the system date and time at the instant the command is executed
Output format:

SID DATE TIME
M CTAG COMPLD
"<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,<TMTYPE>"
;

SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,
<SECOND>,[<DIFFERENCE>][:DST=<DST>];
Sets the system date and time for the NE


19 Test Access

Table 20 Test Access 

CHG-ACCMD-<MOD_TACC>:[<TID>]:<TAP>:<CTAG>::<MD>;
Changes the test access mode for the circuit being tested

CONN-TACC-<MOD_TACC>:[<TID>]:<SRC>:<CTAG>::<TAP>:MD=<MD>;
Connects the STS or VT defined by AID to the STS specified by the TAP number
Output format:

SID DATE TIME
M CTAG COMPLD
"<TAP>"
;

DISC-TACC:[<TID>]:<TAP>:<CTAG>;
Disconnects the TAP and puts the connection back to its original state

RTRV-TACC:[<TID>]:<TAP>:<CTAG>;
Retrieves details associated with a TAP
Output format:

SID DATE TIME
M CTAG COMPLD
"<TAP>:<TACC_AIDA>,<TACC_AIDB>,[<MD>],[<CROSSCONNECTID1>],
[<CROSSCONNECTID2>]"
;


20 Testing

Table 21 Testing 

OPR-LPBK-<MOD2>:[<TID>]:<AID>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>];
Operates a signal loopback on an I/O card or on a cross-connect

RLS-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>];
Releases a signal loopback on an I/O card or on a cross-connect


21 Trace

Table 22 Trace 

RTRV-PTHTRC-<STS_PATH>:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>][:<LOCN>];
Retrieves the contents of the SONET path trace message that is transported in the J1 byte of the SONET STS path
Output format:

SID DATE TIME
M CTAG COMPLD
"<TRACMSG>"
;


22 UCP (Cisco ONS 15454 only)

Table 23 UCP 

DLT-UCP-CC:[<TID>]:<AID>:<CTAG>[::::];
Deletes a UCP IP control channel

DLT-UCP-IF:[<TID>]:<AID>:<CTAG>[::::];
Deletes a UCP interface

DLT-UCP-NBR:[<TID>]:<AID>:<CTAG>[::::];
Deletes a UCP neighbor

ED-UCP-CC:[<TID>]:<AID>:<CTAG>:::[LOCALIPCC=<LOCALIPCC>,]
[REMOTEIPCC=<REMOTEIPCC>,][LMPHELLOINT=<LMPHELLOINT>,]
[LMPHELLODEADINT=<LMPHELLODEADINT>,][MTU=<MTU>,]
[CRCMD=<CRCMD>][:];
Edits UCP IP control channel attributes

ED-UCP-IF:[<TID>]:<AID>:<CTAG>:::[TNATYPE=<TNATYPE>,]
[TNAADDR=<TNAADDR>,][CORENETWORKID=<CORENETWORKID>][:];
Edits UCP interface attributes

ED-UCP-NBR:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>,][HELLOEN=<HELLOEN>,]
[HELLOINT=<HELLOINT>,][REFREDEN=<REFREDEN>][:];
Edits a UCP neighbor

ED-UCP-NODE:[<TID>]::<CTAG>:::[NODEID=<NODEID>,][INITRETRY=<INITRETRY>,]
[MAXRETRY=<MAXRETRY>,][RESTARTTM=<RESTARTTM>,][RECOVTM=<RECOVTM>,]
[RXMTINT=<RXMTINT>,][RFRSHINT=<RFRSHINT>,][RESVTIMEOUT=<RESVTIMEOUT>,]
[RESVCONFTIMEOUT=<RESVCONFTIMEOUT>,][SOURCEDIP=<SOURCEDIP>,]
[DESTINATIONDIP=<DESTINATIONDIP>][:];
Edits a UCP node level attributes

ENT-UCP-CC:[<TID>]:[<AID>]:<CTAG>:::NBRIX=<NBRIX>,CCTYPE=<CCTYPE>,
[PORT=<PORT>,][LOCALCCID=<LOCALCCID>,][LOCALIPCC=<LOCALIPCC>,]
[REMOTCCID=<REMOTECCID>,][REMOTEIPCC=<REMOTEIPCC>,]
[LMPHELLOINT=<LMPHELLOINT>,][LMPHELLODEADINT=<LMPHELLODEADINT>,]
[MTU=<MTU>,][CRCMD=<CRCMD>,][TUNMD=<TUNMD>][:];
Creates a UCP IP control channel

ENT-UCP-IF:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][CCID=<CCID>,]
[LOCALIFID=<LOCALIFID>,][REMOTEIFID=<REMOTEIFID>,][TNATYPE=<TNATYPE>,]
[TNAADDR=<TNAADDR>,][CORENETWORKID=<CORENETWORKID>][:];
Creates a UCP interface

ENT-UCP-NBR:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][NODEID=<NODEID>,]
NAME=<NAME>,[NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,]
[REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>][:];
Creates a UCP neighbor

REPT ALM UCP
Reports an alarm condition against a UCP object

REPT EVT UCP
Reports the occurrence of a non-alarmed event against a UCP object

RTRV-ALM-UCP:[<TID>]:<AID >:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,];
Retrieves and sends the current status of all active alarm conditions against a UCP object
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]"
;

RTRV-COND-UCP:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];
Retrieves the current standing condition against a UCP object
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-UCP-CC:[<TID>]:[<AID >]:<CTAG>[::::];
Retrieves UCP IP control channel attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>]::NBRIX=<NBRIX>,CCTYPE=<CCTYPE>,[PORT=<PORT>,]
LOCALCCID=<LOCALCCID>,LOCALIPCC=<LOCALIPCC>,
REMOTECCID=<REMOTECCID>,[REMOTEIPCC=<REMOTEIPCC>,]
LMPHELLOINT=<LMPHELLOINT>,OPERLMPHELLOINT=<OPERLMPHELLOINT>,
LMPHELLODEADINT=<LMPHELLODEADINT>,
OPERLMPHELLODEADINT=<OPERLMPHELLODEADINT>,
[TUNMD=<TUNMD>,][MTU=<MTU>,][CRCMD=<CRCMD>]"
;

RTRV-UCP-IF:[<TID>]:[<AID>]:<CTAG>[::::];
Retrieves UCP interface attributes
Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>]::NBRIX=<NBRIX>,CCID=<CCID>,LOCALIFID=<LOCALIFID>,
REMOTEIFID=<REMOTEIFID>,TNATYPE=<TNATYPE>,
TNAADDR=<TNAADDR>,CORENETWORKID=<CORENETWORKID>"
;

RTRV-UCP-NBR:[<TID>]:[<AID>]:<CTAG>[::::];
Retrieves a UCP neighbor
Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[NBRIX=<NBRIX>,][NODEID=<NODEID>,][NAME=<NAME>,]
[NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,]
[REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>]"
;

RTRV-UCP-NODE:[<TID>]::<CTAG>[::::];
Retrieves UCP node-level attributes
Output formats:

SID DATE TIME
M CTAG COMPLD
"::[NODEID=<NODEID>,][INITRETRY=<INITRETRY>,][MAXRETRY=<MAXRETRY>,]
[RESTARTTM=<RESTARTTM>,][RECOVTM=<RECOVTM>,][RXMTINT=<RXMTINT>,]
[RFRSHINT=<RFRSHINT>,][RESVTIMEOUT=<RESVTIMEOUT>,]
[RESVCONFTIMEOUT=<RESVCONFTIMEOUT>,]
[SOURCEDIP=<SOURCEDIP>,][DESTINATIONDIP=<DESTINATIONDIP>]"
;


23 Path Protection Switching

Table 24 Path Protection Switching 

REPT SW
Reports the autonomous switching of a unit in a duplex equipment pair to standby and its mate to the active state


24 VCAT

Table 25 VCAT 

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:];
Deletes a virtual concatenated group (VCG) object

ENT-VCG:[<TID>]:<SRC>:<CTAG>:::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,[CCT=<CCT>,
[LCAS=<LCAS>][:];
Creates a VCG object

RTRV-VCG:[<TID>]:<SRC>:<CTAG>[::::];
Retrieves all of the attributes provisioned for a VCG
Output format:

SID DATE TIME
M CTAG COMPLD
"<SRC>::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,CCT=<CCT>,LCAS=<LCAS>"
;